This document provides instructions for disassembling the final drive on a Caterpillar 329D2 L excavator. The process involves:
1. Removing the final drive and separating it from the track assembly and travel motor.
2. Lifting the final drive and disassembling it into components like the cover, carrier assembly, ring gears, and main housing.
3. Using tools like pins, bolts, and lifting devices to separate each part while taking care to mark orientations and support heavy components.
4. Disassembling internal components of the carrier assembly and housing such as planetary gears, shafts, seals, and bearings.
Caterpillar Cat 329D2L Excavator (Prefix WDT) Service Repair Manual (WDT00001...shudun96087
The document provides instructions for disassembling the final drive of a 329D2L excavator in 3 steps:
1. Remove the final drive assembly from the excavator and disassemble it into its main components including the cover, carrier assembly, ring gears, and main housing.
2. Further disassemble the carrier assembly and housing components to separate individual parts like planetary gears, shafts, seals, and bearings.
3. Use the required tools to lift, support, and remove each part, noting weight and orientation details to aid reassembly.
Caterpillar Cat 329D2L Excavator (Prefix WDT) Service Repair Manual (WDT00001...cnp692569
This document provides instructions for disassembling the final drive of a 329D2 L excavator. It begins by removing the final drive assembly and cleaning it. Then various parts like the cover, carrier assembly, ring gears, and housing are removed using specialized tools. Each step provides illustrations and notes cleaning requirements and part weights to aid with the disassembly process. The overall process is described in 33 steps and is intended to fully disassemble the final drive for repair or replacement of components.
Caterpillar Cat 329D2L Excavator (Prefix WDT) Service Repair Manual (WDT00001...kesi7153062
The document provides instructions for disassembling the final drive of a 329D2 L excavator. It describes:
1) Removing the final drive assembly and placing it on a repair stand.
2) Removing the cover by lifting it off with brackets and removing bolts and plugs.
3) Disassembling the internal components of the final drive which includes removing gears, shafts, washers, seals and housings using various tools.
Caterpillar cat 325 c excavator (prefix jld) service repair manual (jld00001 ...fhsejkdkmen
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and disassemble components of the final drive such as gears, carriers, shafts, and housings. Cleanliness is emphasized throughout. The assembly procedure is a reversal of the disassembly steps and involves applying sealants and lubricants to components before reinstalling them.
Caterpillar Cat 325C and 325C L Excavator (Prefix JLD) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for disassembling and removing the final drive from a 325C excavator. It lists the required tools and gives step-by-step details on removing the final drive housing, gears, carrier assemblies, and other components. Alignment marks should be made and weights of parts noted. Care must be taken due to the weights involved, with the final drive assembly weighing approximately 688 pounds and other parts ranging from 70 to 220 pounds.
Caterpillar cat 325 c l excavator (prefix jld) service repair manual (jld0000...fhsejkdkmen
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and disassemble components of the final drive such as gears, carriers, shafts, and housings. Cleanliness is emphasized throughout. The assembly procedure is a reversal of the disassembly steps and involves applying sealants and lubricants to components before reinstalling them.
Caterpillar Cat 325C and 325C L Excavator (Prefix JLD) Service Repair Manual ...zan2736ban
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and disassemble components of the final drive such as gears, carriers, shafts, and housings. Cleanliness is emphasized throughout. The assembly procedure is a reversal of the disassembly steps and involves applying sealants and lubricants to components before reinstalling them.
The document provides instructions for disassembling and removing the final drive from a 325C excavator. It lists the required tools and gives step-by-step details on removing the final drive housing, gears, carrier assemblies, and other components. Alignment marks should be made and weights of parts provided, as some components like the housing weigh over 100kg. Care must be taken when using tools to separate components and remove retaining rings, seals, and bearings from inside the final drive assembly.
Caterpillar Cat 329D2L Excavator (Prefix WDT) Service Repair Manual (WDT00001...shudun96087
The document provides instructions for disassembling the final drive of a 329D2L excavator in 3 steps:
1. Remove the final drive assembly from the excavator and disassemble it into its main components including the cover, carrier assembly, ring gears, and main housing.
2. Further disassemble the carrier assembly and housing components to separate individual parts like planetary gears, shafts, seals, and bearings.
3. Use the required tools to lift, support, and remove each part, noting weight and orientation details to aid reassembly.
Caterpillar Cat 329D2L Excavator (Prefix WDT) Service Repair Manual (WDT00001...cnp692569
This document provides instructions for disassembling the final drive of a 329D2 L excavator. It begins by removing the final drive assembly and cleaning it. Then various parts like the cover, carrier assembly, ring gears, and housing are removed using specialized tools. Each step provides illustrations and notes cleaning requirements and part weights to aid with the disassembly process. The overall process is described in 33 steps and is intended to fully disassemble the final drive for repair or replacement of components.
Caterpillar Cat 329D2L Excavator (Prefix WDT) Service Repair Manual (WDT00001...kesi7153062
The document provides instructions for disassembling the final drive of a 329D2 L excavator. It describes:
1) Removing the final drive assembly and placing it on a repair stand.
2) Removing the cover by lifting it off with brackets and removing bolts and plugs.
3) Disassembling the internal components of the final drive which includes removing gears, shafts, washers, seals and housings using various tools.
Caterpillar cat 325 c excavator (prefix jld) service repair manual (jld00001 ...fhsejkdkmen
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and disassemble components of the final drive such as gears, carriers, shafts, and housings. Cleanliness is emphasized throughout. The assembly procedure is a reversal of the disassembly steps and involves applying sealants and lubricants to components before reinstalling them.
Caterpillar Cat 325C and 325C L Excavator (Prefix JLD) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for disassembling and removing the final drive from a 325C excavator. It lists the required tools and gives step-by-step details on removing the final drive housing, gears, carrier assemblies, and other components. Alignment marks should be made and weights of parts noted. Care must be taken due to the weights involved, with the final drive assembly weighing approximately 688 pounds and other parts ranging from 70 to 220 pounds.
Caterpillar cat 325 c l excavator (prefix jld) service repair manual (jld0000...fhsejkdkmen
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and disassemble components of the final drive such as gears, carriers, shafts, and housings. Cleanliness is emphasized throughout. The assembly procedure is a reversal of the disassembly steps and involves applying sealants and lubricants to components before reinstalling them.
Caterpillar Cat 325C and 325C L Excavator (Prefix JLD) Service Repair Manual ...zan2736ban
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and disassemble components of the final drive such as gears, carriers, shafts, and housings. Cleanliness is emphasized throughout. The assembly procedure is a reversal of the disassembly steps and involves applying sealants and lubricants to components before reinstalling them.
The document provides instructions for disassembling and removing the final drive from a 325C excavator. It lists the required tools and gives step-by-step details on removing the final drive housing, gears, carrier assemblies, and other components. Alignment marks should be made and weights of parts provided, as some components like the housing weigh over 100kg. Care must be taken when using tools to separate components and remove retaining rings, seals, and bearings from inside the final drive assembly.
Caterpillar Cat 325C L Excavator (Prefix JLD) Service Repair Manual (JLD00001...f8uesjdkdmdm
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and disassemble components of the final drive such as gears, carriers, shafts, and housings. Cleanliness is emphasized throughout. The assembly procedure is largely the reverse of the disassembly steps and involves applying sealants and lubricants before reinstalling components.
Caterpillar cat 325 c l excavator (prefix jld) service repair manual (jld0000...ikdkkdmdmdm
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and disassemble components of the final drive such as gears, carriers, shafts, and housings. Cleanliness is emphasized throughout. The assembly procedure is a reversal of the disassembly steps and involves applying sealants and lubricants to components before reinstalling them.
Caterpillar Cat 325C L Excavator (Prefix JLD) Service Repair Manual (JLD00001...f7fujksekmdm8u
The document provides instructions for disassembling and removing the final drive from a 325C excavator. It lists the required tools and gives step-by-step details on removing the final drive housing, gears, shafts, and other components. Alignment marks should be made and weights of parts provided, as the components must be reinstalled in their original locations. Careful cleaning is important to prevent dirt from entering the mechanism during disassembly.
The document provides instructions for disassembling and removing the final drive from a 325C excavator. It lists the required tools and gives step-by-step details on removing the final drive housing, gears, carrier assemblies, and other components. Alignment marks should be made and weights of parts provided, as some components like the housing weigh over 100kg. Care must be taken during disassembly to prevent dirt from entering internal mechanisms.
Caterpillar cat 325 c excavator (prefix jld) service repair manual (jld00001 ...ikdkkdmdmdm
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and disassemble components of the final drive such as gears, carriers, shafts, and housings. Cleanliness is emphasized throughout. The assembly procedure is a reversal of the disassembly steps and involves applying sealants and lubricants to components before reinstalling them.
Caterpillar Cat 325C L Excavator (Prefix JLD) Service Repair Manual (JLD00001...f8sejdkdmdijd
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and disassemble components of the final drive such as gears, carriers, shafts, and housings. Cleanliness is emphasized throughout. The assembly procedure is largely the reverse of the disassembly steps and involves applying sealants and lubricants before reinstalling components.
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and install components like gears, carriers, seals, and housings. Cleanliness is emphasized and O-rings, gaskets, and seals should always be replaced. The assembly procedure is the reverse of the disassembly with tools and compounds used to install specific parts correctly.
Caterpillar Cat 325C and 325C L Excavator (Prefix JLD) Service Repair Manual ...fujkskemdmdm4r
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and install components like gears, carriers, seals, and housings. Cleanliness is emphasized and O-rings, gaskets, and seals should always be replaced. The assembly procedure is the reverse of the disassembly with notes to apply lubricants and check parts for wear.
The document provides instructions for disassembling and removing the final drive from a 325C excavator. It lists the required tools and gives step-by-step details on removing the final drive housing, gears, shafts, and other components. Alignment marks should be made and weights of parts provided, as the components must be reinstalled in their original locations. Careful cleaning is important to prevent dirt from entering the mechanism during disassembly.
Caterpillar Cat 325C L Excavator (Prefix JLD) Service Repair Manual (JLD00001...ufs89eodkdmdm
The document provides instructions for disassembling and removing the final drive from a 325C excavator. It lists the required tools and gives step-by-step details on removing the final drive housing, gears, carrier assemblies, and other components. Alignment marks should be made and weights of parts noted. Care must be taken due to the weights involved, with the final drive assembly weighing approximately 688 pounds and other parts ranging from 70 to 220 pounds.
Caterpillar Cat 325C L Excavator (Prefix JLD) Service Repair Manual (JLD00001...jdkskmmdmd1
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and install components like gears, carriers, seals, and housings. Cleanliness is emphasized throughout and O-rings, gaskets, and seals should always be replaced. The assembly procedure is the reverse of the disassembly with notes to apply lubricants and check parts for wear.
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and install components like gears, carriers, seals, and housings. Cleanliness is emphasized and O-rings, gaskets, and seals should always be replaced. The assembly procedure is the reverse of the disassembly with notes to apply lubricants and check parts for wear.
Caterpillar Cat 325C and 325C L Excavator (Prefix JLD) Service Repair Manual ...fskekkdmdmdm3e
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and install components like gears, carriers, seals, and housings. Cleanliness is emphasized and O-rings, gaskets, and seals should always be replaced. The assembly procedure is the reverse of the disassembly with notes to apply lubricants and check parts for wear.
Caterpillar Cat 325C L Excavator (Prefix JLD) Service Repair Manual (JLD00001...jdkskmdmdm
The document provides instructions for disassembling and removing the final drive from a 325C excavator. It lists the required tools and gives step-by-step details on removing the final drive housing, gears, carrier assemblies, and other components. Alignment marks should be made and weights of parts noted. Care must be taken due to the weights involved, with the final drive assembly weighing approximately 688 pounds and other parts ranging from 70 to 220 pounds.
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and install components like gears, carriers, seals, and housings. Cleanliness is emphasized and O-rings, gaskets, and seals should always be replaced. The assembly procedure is the reverse of the disassembly with notes to apply lubricants and check parts for wear.
Caterpillar Cat 325C L Excavator (Prefix JLD) Service Repair Manual (JLD00001...pwg56547003
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and disassemble components of the final drive such as gears, carriers, shafts, and housings. Cleanliness is emphasized throughout. The assembly procedure is a reversal of the disassembly steps and involves applying sealants and lubricants to components before reinstalling them.
Caterpillar Cat 390F L Excavator (Prefix MGF) Service Repair Manual (MGF00001...uddksemd8ud
This document provides instructions for disassembling and assembling the travel motor on a 390F L Excavator. It describes 40 steps to disassemble the various components of the travel motor including removing seals, springs, pistons, plates, and bearings. It then describes the assembly process in reverse, providing details on cleaning parts and applying lubricant before reinstalling components in the proper order and orientation.
The document provides instructions for removing and installing a piston pump used for hoist and steering functions on a Caterpillar 725C articulated truck. The removal process involves taking off the cab, then disconnecting hydraulic lines and electrical connectors from the pump. Individual components are then removed from the pump housing in reverse order of the installation instructions. Proper safety precautions and cleaning of parts is emphasized during disassembly and reassembly.
The document provides instructions for disassembling and assembling the freewheel stator of a torque converter. It lists 35 steps for disassembly, removing components like bolts, valves, sensors, gears, bearings and seals. It then lists 29 steps for assembly, installing these components in reverse order. Cleanliness is emphasized throughout to prevent dirt from entering components. Various tools are required, including link brackets, eyebolts and retaining ring pliers.
Caterpillar Cat 390F Mobile Hydraulic Excavator (Prefix B37) Service Repair M...uddksemd8ud
This document provides instructions for disassembling and assembling the travel motor on a 390F Hydraulic Excavator. The disassembly procedure involves 40 steps to remove components like the head, relief valves, spools, pistons, and seals. The assembly procedure reverses the disassembly steps and involves installing components in the correct order and orientation, with notes about cleaning, marking, and applying lubricant to parts. Precautions are provided regarding spring-loaded components.
Caterpillar Cat 390F L Excavator (Prefix TYE) Service Repair Manual (TYE00001...uddksemd8ud
This document provides instructions for disassembling and assembling the travel motor of a 390F L Excavator. It describes 40 steps for disassembly, including removing covers, pistons, springs, seals and other components. It then describes 36 steps for reassembly, including installing seals, bearings, pistons, springs and covers. Precise alignment marks are required for accurate reassembly. Cleanliness is critical and tools are needed to remove and install certain parts.
This document provides assembly instructions for a final drive in 29 steps. It lists required tools and parts. Key steps include: installing bearings and seals; determining bearing preload using shims; assembling carrier assemblies with planetary gears; and installing ring gears, covers, and bolts. Proper cleaning, lubrication and torque specifications are noted throughout assembly.
More Related Content
Similar to Caterpillar Cat 329D2L Excavator (Prefix WDT) Service Repair Manual (WDT00001 and up).pdf
Caterpillar Cat 325C L Excavator (Prefix JLD) Service Repair Manual (JLD00001...f8uesjdkdmdm
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and disassemble components of the final drive such as gears, carriers, shafts, and housings. Cleanliness is emphasized throughout. The assembly procedure is largely the reverse of the disassembly steps and involves applying sealants and lubricants before reinstalling components.
Caterpillar cat 325 c l excavator (prefix jld) service repair manual (jld0000...ikdkkdmdmdm
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and disassemble components of the final drive such as gears, carriers, shafts, and housings. Cleanliness is emphasized throughout. The assembly procedure is a reversal of the disassembly steps and involves applying sealants and lubricants to components before reinstalling them.
Caterpillar Cat 325C L Excavator (Prefix JLD) Service Repair Manual (JLD00001...f7fujksekmdm8u
The document provides instructions for disassembling and removing the final drive from a 325C excavator. It lists the required tools and gives step-by-step details on removing the final drive housing, gears, shafts, and other components. Alignment marks should be made and weights of parts provided, as the components must be reinstalled in their original locations. Careful cleaning is important to prevent dirt from entering the mechanism during disassembly.
The document provides instructions for disassembling and removing the final drive from a 325C excavator. It lists the required tools and gives step-by-step details on removing the final drive housing, gears, carrier assemblies, and other components. Alignment marks should be made and weights of parts provided, as some components like the housing weigh over 100kg. Care must be taken during disassembly to prevent dirt from entering internal mechanisms.
Caterpillar cat 325 c excavator (prefix jld) service repair manual (jld00001 ...ikdkkdmdmdm
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and disassemble components of the final drive such as gears, carriers, shafts, and housings. Cleanliness is emphasized throughout. The assembly procedure is a reversal of the disassembly steps and involves applying sealants and lubricants to components before reinstalling them.
Caterpillar Cat 325C L Excavator (Prefix JLD) Service Repair Manual (JLD00001...f8sejdkdmdijd
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and disassemble components of the final drive such as gears, carriers, shafts, and housings. Cleanliness is emphasized throughout. The assembly procedure is largely the reverse of the disassembly steps and involves applying sealants and lubricants before reinstalling components.
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and install components like gears, carriers, seals, and housings. Cleanliness is emphasized and O-rings, gaskets, and seals should always be replaced. The assembly procedure is the reverse of the disassembly with tools and compounds used to install specific parts correctly.
Caterpillar Cat 325C and 325C L Excavator (Prefix JLD) Service Repair Manual ...fujkskemdmdm4r
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and install components like gears, carriers, seals, and housings. Cleanliness is emphasized and O-rings, gaskets, and seals should always be replaced. The assembly procedure is the reverse of the disassembly with notes to apply lubricants and check parts for wear.
The document provides instructions for disassembling and removing the final drive from a 325C excavator. It lists the required tools and gives step-by-step details on removing the final drive housing, gears, shafts, and other components. Alignment marks should be made and weights of parts provided, as the components must be reinstalled in their original locations. Careful cleaning is important to prevent dirt from entering the mechanism during disassembly.
Caterpillar Cat 325C L Excavator (Prefix JLD) Service Repair Manual (JLD00001...ufs89eodkdmdm
The document provides instructions for disassembling and removing the final drive from a 325C excavator. It lists the required tools and gives step-by-step details on removing the final drive housing, gears, carrier assemblies, and other components. Alignment marks should be made and weights of parts noted. Care must be taken due to the weights involved, with the final drive assembly weighing approximately 688 pounds and other parts ranging from 70 to 220 pounds.
Caterpillar Cat 325C L Excavator (Prefix JLD) Service Repair Manual (JLD00001...jdkskmmdmd1
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and install components like gears, carriers, seals, and housings. Cleanliness is emphasized throughout and O-rings, gaskets, and seals should always be replaced. The assembly procedure is the reverse of the disassembly with notes to apply lubricants and check parts for wear.
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and install components like gears, carriers, seals, and housings. Cleanliness is emphasized and O-rings, gaskets, and seals should always be replaced. The assembly procedure is the reverse of the disassembly with notes to apply lubricants and check parts for wear.
Caterpillar Cat 325C and 325C L Excavator (Prefix JLD) Service Repair Manual ...fskekkdmdmdm3e
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and install components like gears, carriers, seals, and housings. Cleanliness is emphasized and O-rings, gaskets, and seals should always be replaced. The assembly procedure is the reverse of the disassembly with notes to apply lubricants and check parts for wear.
Caterpillar Cat 325C L Excavator (Prefix JLD) Service Repair Manual (JLD00001...jdkskmdmdm
The document provides instructions for disassembling and removing the final drive from a 325C excavator. It lists the required tools and gives step-by-step details on removing the final drive housing, gears, carrier assemblies, and other components. Alignment marks should be made and weights of parts noted. Care must be taken due to the weights involved, with the final drive assembly weighing approximately 688 pounds and other parts ranging from 70 to 220 pounds.
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and install components like gears, carriers, seals, and housings. Cleanliness is emphasized and O-rings, gaskets, and seals should always be replaced. The assembly procedure is the reverse of the disassembly with notes to apply lubricants and check parts for wear.
Caterpillar Cat 325C L Excavator (Prefix JLD) Service Repair Manual (JLD00001...pwg56547003
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and disassemble components of the final drive such as gears, carriers, shafts, and housings. Cleanliness is emphasized throughout. The assembly procedure is a reversal of the disassembly steps and involves applying sealants and lubricants to components before reinstalling them.
Similar to Caterpillar Cat 329D2L Excavator (Prefix WDT) Service Repair Manual (WDT00001 and up).pdf (16)
Caterpillar Cat 390F L Excavator (Prefix MGF) Service Repair Manual (MGF00001...uddksemd8ud
This document provides instructions for disassembling and assembling the travel motor on a 390F L Excavator. It describes 40 steps to disassemble the various components of the travel motor including removing seals, springs, pistons, plates, and bearings. It then describes the assembly process in reverse, providing details on cleaning parts and applying lubricant before reinstalling components in the proper order and orientation.
The document provides instructions for removing and installing a piston pump used for hoist and steering functions on a Caterpillar 725C articulated truck. The removal process involves taking off the cab, then disconnecting hydraulic lines and electrical connectors from the pump. Individual components are then removed from the pump housing in reverse order of the installation instructions. Proper safety precautions and cleaning of parts is emphasized during disassembly and reassembly.
The document provides instructions for disassembling and assembling the freewheel stator of a torque converter. It lists 35 steps for disassembly, removing components like bolts, valves, sensors, gears, bearings and seals. It then lists 29 steps for assembly, installing these components in reverse order. Cleanliness is emphasized throughout to prevent dirt from entering components. Various tools are required, including link brackets, eyebolts and retaining ring pliers.
Caterpillar Cat 390F Mobile Hydraulic Excavator (Prefix B37) Service Repair M...uddksemd8ud
This document provides instructions for disassembling and assembling the travel motor on a 390F Hydraulic Excavator. The disassembly procedure involves 40 steps to remove components like the head, relief valves, spools, pistons, and seals. The assembly procedure reverses the disassembly steps and involves installing components in the correct order and orientation, with notes about cleaning, marking, and applying lubricant to parts. Precautions are provided regarding spring-loaded components.
Caterpillar Cat 390F L Excavator (Prefix TYE) Service Repair Manual (TYE00001...uddksemd8ud
This document provides instructions for disassembling and assembling the travel motor of a 390F L Excavator. It describes 40 steps for disassembly, including removing covers, pistons, springs, seals and other components. It then describes 36 steps for reassembly, including installing seals, bearings, pistons, springs and covers. Precise alignment marks are required for accurate reassembly. Cleanliness is critical and tools are needed to remove and install certain parts.
This document provides assembly instructions for a final drive in 29 steps. It lists required tools and parts. Key steps include: installing bearings and seals; determining bearing preload using shims; assembling carrier assemblies with planetary gears; and installing ring gears, covers, and bolts. Proper cleaning, lubrication and torque specifications are noted throughout assembly.
Caterpillar Cat 365B L MH EXCAVATOR (Prefix CTY) Service Repair Manual (CTY00...uddksemd8ud
This document provides assembly instructions for a final drive in 29 steps. It lists required tools and parts. Key steps include: installing bearings and seals; determining bearing preload using shims; assembling carrier assemblies with planetary gears; and installing ring gears, covers, and bolts. Proper cleaning, lubrication and torque specifications are noted throughout assembly.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3176C engine. It describes removing components like sensors, tubes, and manifolds. It instructs to clean mating surfaces and inspect for damage. The correct cylinder head gasket must be installed along with new seals. Bolts are tightened in a specific sequence to the proper torques. Removed components are reinstalled in reverse order.
This document provides instructions for disassembling and assembling the travel motor on a 352F excavator. The disassembly procedure involves removing 17 components from the travel motor housing including the head assembly, brake housing, rotating group, barrel assembly, pistons, and bearings. The assembly procedure instructs installing the components in reverse order.
Caterpillar Cat 345C L Mobile Hydraulic Excavator (Prefix M3E) Service Repair...uddksemd8ud
The document provides instructions for disassembling and assembling a travel motor. Key steps include removing the head, brake piston, rotating group, and seals. Components must be cleaned and any worn parts replaced with new ones. Proper identification and orientation of parts is important for correct reassembly, which involves installing seals, spacers, pistons and other components in the correct order. Contamination of hydraulic systems must be avoided during the process.
This document provides instructions for disassembling and assembling the travel motor of a 336E excavator. The disassembly process involves removing 27 different components of the travel motor including the head, springs, brake piston, plates, and seals. The assembly process reverses the disassembly steps and includes lubricating components and ensuring proper alignment of parts. Tools such as an eyebolt, retaining ring pliers, and bearing puller are required to complete the process.
The document provides instructions to remove the rear power take-off (RPTO) from a Caterpillar C9.3 engine. The steps are:
1. Remove the flywheel housing to access the RPTO.
2. Disconnect the drive shaft from the RPTO and remove retaining bolts.
3. Lift the RPTO straight up to remove.
Caterpillar Cat 340F L LRE Excavator (Prefix YBF) Service Repair Manual (YBF0...uddksemd8ud
This document provides the disassembly and assembly procedures for the travel motor on a 340F L LRE excavator. It includes 27 steps to disassemble the travel motor by removing components like the head, springs, plates, seals and bearings. The 27 steps to assemble list installing these same components in reverse order and include notes about lubrication, alignment and torque specifications. Required tools are listed for both procedures.
The document provides instructions for disassembling a piston motor (hydraulic fan) with the following key steps:
1. Remove the head and internal components like seals, plates, and bearings.
2. Extract the pistons, retainer, and bearings from the housing.
3. Use specialty tools to remove the retaining ring and springs, allowing removal of the swashplate and shaft.
Proper safety precautions and cleaning of parts is emphasized before disassembly.
The document provides instructions for removing and installing an engine oil filter base on a 336D LN excavator. It describes:
1) Removing various connectors, seals, valves, and plugs from the engine oil filter base during disassembly.
2) Assembling the engine oil filter base by installing plugs, seals, valves, and connectors in reverse order of removal.
3) Installing the engine oil filter base on the engine using guide studs and bolts, and reconnecting hoses.
The document provides instructions for installing a fuel injection pump on a Caterpillar 330 excavator engine:
1. Install alignment tools and spacers to hold the fuel injection pump and rack in position. Lubricate seals and install the pump, securing it with a bushing.
2. Use a measurement tool to check that the rack has the proper travel of 15.70 mm after installation.
3. Repeat the process to install the remaining fuel injection pumps and reinstall the cover.
The document provides instructions for installing a cylinder head on a Caterpillar 330 excavator engine. It describes:
1. Cleaning the cylinder head and ensuring it is free of contaminants before installation.
2. Attaching the cylinder head to the cylinder block using bolts in the specified tightening sequence and torque.
3. Reinstalling related components like the exhaust manifold, fuel injection lines, and valve train once the cylinder head is secured.
The summary highlights the key steps of cleaning the cylinder head, attaching it to the engine block, and reinstalling additional parts. It is provided in 3 sentences as requested.
Caterpillar Cat 330D N Hydraulic Excavator (Prefix RAS) Service Repair Manual...uddksemd8ud
The document provides instructions for removing and disassembling the swivel component of a 330D L hydraulic excavator. It lists required tools and outlines a 15 step procedure for removing the swivel that includes disconnecting hydraulic lines, removing bolts and other fasteners, and using lifting devices. A 7 step procedure is then given for disassembling the swivel once it is removed, which involves cleaning it, positioning it on a repair stand, and separating its outer housing from the rotor using bolts and other tools.
Caterpillar Cat 330D L Hydraulic Excavator (Prefix RAS) Service Repair Manual...uddksemd8ud
The document provides instructions for removing and disassembling the swivel component of a 330D L hydraulic excavator. It begins with preparing the hydraulic system by releasing pressure and applying vacuum. The swivel is then removed by disconnecting hoses, removing bolts and lifting it off. For disassembly, the swivel is cleaned and secured on a repair stand. Bolts, seals and housing components are then removed to separate the rotor from the outside housing.
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C MH excavator.
2) It lists 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) It then lists 28 steps for assembly in reverse order, providing details on installing components and applying sealant or lubricant.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 329D2 L EXCAVATOR WDT
Configuration: 329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
326D2, 329D2 and 330D2 Excavators Machine Systems
Media Number -UENR6134-08 Publication Date -01/09/2018 Date Updated -12/09/2018
i05453056
Final Drive - Remove
SMCS - 4050-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8S-7611 Handle As 2
8S-7615 Pin As 2
283-1495 Stand Assembly 2
B 439-3939 Link Bracket As 2
C
154-6184 Forcing Bolt (M 20) 2
154-6185(1)
Forcing Bolt (M 24) 2
(1)
For Use on 329 and 330 sales models
Start By:
a. Separate the track assembly.
b. Remove the travel motor.
1/3
329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine(SEB...
2020/4/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00489826
Typical Example
Note: Adjust the height of Tooling (A) so that there is sufficient clearance between the
sprocket and the track for the removal of the final drive.
1. Lift the side of the machine in order to install Tooling (A) under the frame, as shown.
Illustration 2 g00712767
2. Fasten Tooling (B) and a suitable lifting device to final drive (1), as shown. Put a slight
lifting tension on the final drive.
Illustration 3 g00712737
2/3
329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine(SEB...
2020/4/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Note: Mark the orientation of bolt holes (2) for the travel motor for installation purposes.
3. Remove bolts (3) and the washers from the final drive.
Illustration 4 g00712749
4. Use Tooling (C) in order to remove the final drive from the frame.
5. Carefully remove final drive (1). The weight of final drive (1) and the sprocket is
approximately 312 kg (688 lb).
6. Remove Tooling (C) from the frame.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Apr 30 08:38:20 UTC+0800 2020
3/3
329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine(SEB...
2020/4/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 329D2 L EXCAVATOR WDT
Configuration: 329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
326D2, 329D2 and 330D2 Excavators Machine Systems
Media Number -UENR6134-08 Publication Date -01/09/2018 Date Updated -12/09/2018
i02606369
Final Drive - Disassemble
SMCS - 4050-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 138-7573 Link Bracket 2
C 154-6181 Forcing Screw 1
D 138-7574 Link Bracket 2
E
5F-7366 Forcing Screw 1
1P-5546 Crossblock 1
1U-9889 Crossblock 1
1P-0520 Driver Group 1
6V-7888 Puller Leg 2
1H-3112 Puller Assembly 1
1P-5551 Adjustable Screw Assembly 1
F 1U-8846 Gasket Sealant 1
Start By:
a. Remove the final drive. Refer to Disassembly and Assembly, "Final Drive - Remove".
1/11
329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine(SEB...
2020/4/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of
the component should be thoroughly cleaned. This will prevent dirt from entering the
internal mechanism.
1. Put an alignment mark across the sections of the final drive for assembly purposes. The
parts must be reinstalled in the part's original locations.
Illustration 1 g00708089
2. Fasten the final drive to Tooling (A), as shown. The combined weight of the final drive and
final drive sprocket is approximately 312 kg (688 lb).
3. Remove bolts (1) and the washers that hold the cover in position.
Illustration 2 g00708090
4. Remove the setscrews from the cover. Fasten Tooling (B) and a suitable lifting device to
cover (2), as shown. The weight of cover (2) is approximately 32 kg (70 lb). Remove cover
(2).
2/11
329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine(SEB...
2020/4/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 3 g00708091
5. Remove thrust plate (3) from cover (2).
6. Remove plugs (4) from cover (2).
Illustration 4 g00708235
7. Remove O-ring seals (5) from both plugs (4) that were in the cover.
Illustration 5 g00708092
8. Remove spacer (6) from carrier assembly (7).
9. Remove sun gear (8) from carrier assembly (7).
3/11
329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine(SEB...
2020/4/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. 10. Remove carrier assembly (7) by lifting the carrier assembly straight up. The weight of
carrier assembly (7) is approximately 14 kg (30 lb).
Illustration 6 g01304883
11. Disassemble carrier assembly (7), as follows.
a. Drive spring pin (10) into planetary shaft (9) with a hammer and a punch.
Illustration 7 g00708144
b. Remove planetary shaft (9) with spring pin (10) from the carrier assembly.
c. Remove spring pin (10) from planetary shaft (9) with a hammer and a punch.
4/11
329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine(SEB...
2020/4/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 8 g00708218
d. Remove thrust washers (11) and planetary gear (13) from the carrier assembly.
e. Remove bearing (12) from planetary gear (13).
12. Repeat Steps 11.a through 11.e in order to remove the remaining planetary gears from the
carrier assembly.
Illustration 9 g00708162
13. Remove sun gear (14) from carrier assembly (15).
Illustration 10 g00708325
14. Remove spacer (16).
5/11
329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine(SEB...
2020/4/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 11 g00708184
Note: It will be necessary to pry ring gears (17) away from main housing (18) in order to
install the lifting slings.
15. Fasten a suitable lifting device to ring gears (17), as shown. Remove the ring gears from
main housing (18). The weight of ring gears (17) is approximately 45 kg (100 lb).
Illustration 12 g00708360
16. Use a screwdriver or a chisel in order to separate the two ring gears (17).
Note: The two ring gears are held together with Tooling (F). It may be necessary to heat the
ring gears in order to soften the sealant. Do not heat over 135 °C (275 °F) for more than
thirty minutes.
6/11
329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine(SEB...
2020/4/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 13 g00708172
17. Position a 12.7 mm (0.50 inch) shackle under carrier assembly (15).
18. Fasten a suitable lifting device to the shackle.
19. Slowly lift carrier assembly (15) from the final drive. The weight of carrier assembly (15) is
approximately 39 kg (85 lb).
20. Disassemble carrier assembly (15), as follows.
Illustration 14 g00708175
a. Drive spring pin (20) into planetary shaft (19) with a hammer and a punch.
7/11
329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine(SEB...
2020/4/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 15 g00708370
Illustration 16 g00708220
b. Remove planetary shaft (19) with spring pin (20) from the carrier assembly.
c. Remove spring pin (20) from planetary shaft (19) with a hammer and a punch.
d. Remove thrust washers (21) and planetary gear (23) from the carrier assembly.
e. Remove bearings (22) from planetary gear (23).
21. Repeat Steps 20.a through 20.e in order to remove the remaining planetary gears from the
carrier.
Illustration 17 g00708186
22. Remove O-ring seal (24) from main housing (18).
8/11
329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine(SEB...
2020/4/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 18 g00708187
23. Remove bolts (25) from gear (26).
Illustration 19 g00708202
24. Use Tooling (C) in order to remove gear (26) from main housing (18).
Note: The motor housing will separate from the main housing (18) once gear (26) is
removed. Make sure that the motor housing is supported.
Illustration 20 g00708211
25. Remove shims (27) from the main housing.
9/11
329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine(SEB...
2020/4/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 21 g00708212
26. Fasten Tooling (D) and a suitable lifting device to main housing (18), as shown.
27. Use a hammer and a punch in order to separate main housing (18) and the final drive
sprocket from the motor housing (28). The combined weight of main housing (18) and the
final drive sprocket is approximately 82 kg (180 lb).
Illustration 22 g00708214
28. Remove Duo-Cone seal (29) from motor housing (28).
29. Remove alignment pins (30).
10/11
329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine(S...
2020/4/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 23 g00708215
Illustration 24 g00708216
30. Remove Duo-Cone seal (31) from main housing (18).
31. Use Tooling (E) in order to remove bearings (32) and (33) from the main housing.
32. If necessary, remove the final drive sprocket from the main housing.
33. Refer to Disassembly and Assembly, "Final Drive Sprocket - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Apr 30 08:39:16 UTC+0800 2020
11/11
329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine(S...
2020/4/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 329D2 L EXCAVATOR WDT
Configuration: 329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
326D2, 329D2 and 330D2 Excavators Machine Systems
Media Number -UENR6134-08 Publication Date -01/09/2018 Date Updated -12/09/2018
i03508206
Final Drive - Disassemble
SMCS - 4050-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 138-7573 Link Bracket 2
C 1P-1863 Retaining Ring Pliers 1
D 138-7575 Link Bracket 3
E 4C-8359 Eyebolt 2
F 138-7574 Link Bracket 2
G 138-7576 Link Bracket 2
Start By:
a. Start by removing the final drive. Refer to Disassembly and Assembly, "Final Drive -
Remove".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of
the component should be thoroughly cleaned. This will prevent dirt from entering the
internal mechanism.
1. Put an alignment mark across the sections of the final drive for assembly purposes. The
parts must be reinstalled to the original locations.
1/12
329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine(SEB...
2020/4/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 1 g00892878
2. Use Tooling (G) and a suitable lifting device to position the final drive assembly onto
Tooling (A). The weight of the final drive assembly is approximately 550 kg (1200 lb).
3. Remove bolts (1).
Illustration 2 g00892883
4. Use Tooling (B) and a suitable lifting device to remove cover (2). The weight of cover (2) is
approximately 32 kg (70 lb).
Illustration 3 g00892888
2/12
329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine(SEB...
2020/4/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. 5. Remove bolts (3) and gear (4). Check plate (6). Replace plate (6) if plate (6) is worn.
Remove plugs (5) from cover (2).
Illustration 4 g00892906
6. Remove O-ring seals (7) from plugs (5).
Illustration 5 g00892930
7. Remove gear (8) and spacer (9).
Illustration 6 g00892965
3/12
329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine(SEB...
2020/4/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 8. Use Tooling (C) to remove retaining ring (10). Remove washer (11) and gear (12). Remove
bearing assembly (13) and washer (14).
9. Repeat Step 8 for the other two gear assemblies.
Illustration 7 g00892968
10. Remove retaining ring (15).
Illustration 8 g00892975
11. Remove carrier assembly (16).
4/12
329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine(SEB...
2020/4/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 9 g01389804
12. Use a suitable press to remove the shafts from carrier assembly (16).
Illustration 10 g00892977
13. Remove gear (17) and spacer (18).
Illustration 11 g00892997
5/12
329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine(SEB...
2020/4/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. 14. Use Tooling (D) and a suitable lifting device to remove planetary carrier (19). The weight of
planetary carrier (19) is approximately 48 kg (105 lb).
Illustration 12 g00893019
15. Remove retaining ring (21). Lift planetary carrier (19) off sun gear (20).
Illustration 13 g00896860
16. Drive spring pin (23) into planetary shaft (22).
Illustration 14 g00893043
6/12
329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine(SEB...
2020/4/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. 17. Remove planetary shaft (22). Use a suitable punch to remove spring pin (23) from planetary
shaft (22).
Illustration 15 g00896863
18. Remove washers (24) and bearing (25) from planetary gear (26).
19. Repeat Steps 16 through 18 for the other two planetary gears.
Illustration 16 g01842853
20. Remove gear (27). Remove spacer (27A).
Illustration 17 g01842974
7/12
329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine(SEB...
2020/4/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. 21. Use two people to remove carrier assembly (28). The weight of carrier assembly (28) is
approximately 38 kg (85 lb).
Illustration 18 g01843140
22. Drive spring pin (30) into shaft (29).
Illustration 19 g00893658
23. Remove shaft (29). Use a suitable punch to remove spring pin (30) from shaft (29).
Illustration 20 g00893674
24. Remove washers (31) and bearings (32) from planetary gear (33).
8/12
329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine(SEB...
2020/4/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. 25. Repeat Steps 22 through 24 for the other three planetary gears.
Illustration 21 g01208300
26. Fasten Tooling (E) and a suitable lifting device to ring gear (34), as shown. Remove ring
gear (34) from sprocket housing (35). The weight of ring gear (34) is approximately 66 kg
(146 lb).
Illustration 22 g01208542
27. Remove O-ring seal (36) from sprocket housing (35).
Illustration 23 g01208553
9/12
329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine(SEB...
2020/4/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. 28. Remove bolts (37) from coupling gear (38).
Illustration 24 g01208572
29. Install suitable forcing bolts (39) in coupling gear (38). Tighten the forcing bolts evenly in
order to loosen coupling gear (38). Remove the coupling gear from the motor housing.
Illustration 25 g01208578
Illustration 26 g01208625
30. Remove shims (40) from the motor housing.
10/12
329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine(S...
2020/4/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Note: Inner cones and outer bearing cones (42) are a slip fit on the motor housing. While
you remove sprocket housing (35) from the motor housing, inner bearing cone (42) may
stay with the sprocket housing or the inner bearing cone may stay on the motor housing.
31. Fasten Tooling (F) and a suitable lifting device to sprocket housing (35). Separate the
sprocket housing from the motor housing. The weight of sprocket housing (35) is
approximately 109 kg (240 lb).
Illustration 27 g01208626
32. Remove the locating pins from the motor housing.
33. Remove Duo-Cone seal (41) from the motor housing.
34. If inner bearing cone (42) remained on the motor housing, then remove the inner bearing
cone.
Illustration 28 g01208633
35. Remove Duo-Cone seal (43) from the sprocket housing.
36. If inner bearing cone (42) remained on the sprocket housing, then remove the inner bearing
cone.
37. Remove the bearing cups from the sprocket housing.
Thu Apr 30 08:40:12 UTC+0800 2020
11/12
329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine(S...
2020/4/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...