The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and disassemble components of the final drive such as gears, carriers, shafts, and housings. Cleanliness is emphasized throughout. The assembly procedure is a reversal of the disassembly steps and involves applying sealants and lubricants to components before reinstalling them.
Caterpillar cat 325 c excavator (prefix jld) service repair manual (jld00001 ...fjkskedmme
The document provides instructions for disassembling a final drive component from an excavator. It lists the required tools and gives step-by-step instructions to remove the final drive housing, gears, shafts, seals, and other internal parts. Detailed illustrations accompany each step. Disassembly involves removing retaining rings, gears, shafts, bearings, seals, and other parts from the housing using various tools, including a press, hammer, and pullers. Cleanliness is emphasized to prevent dirt from entering during disassembly.
Caterpillar cat 325 c l excavator (prefix bmm) service repair manual (bmm0000...fjkskedmme
The document provides step-by-step instructions to disassemble a final drive assembly for 325C and 325C L excavators. It begins by removing the final drive from the machine and securing it to a repair stand. Various gears, seals, bearings and housings are then removed through 32 numbered steps. Cleanliness is emphasized to prevent dirt from entering components. Tools required are listed in a table.
Caterpillar cat 328 d lcr excavator (prefix gtn) service repair manual (gtn00...fjsekdmmeed
The document provides instructions for disassembling the final drive of a 328D LCR excavator. It lists the required tools and presents a step-by-step process to remove parts such as gears, shafts, bearings, seals, and housings. Detailed illustrations accompany each step to show how to properly disassemble the various components using specialized tools like link brackets, forcing bolts, and pullers. The goal is to fully separate all parts of the final drive assembly for maintenance or repair purposes.
Caterpillar cat 328 d lcr excavator (prefix mkr) service repair manual (mkr00...fjsekdmmeed
The document provides instructions for disassembling the final drive of a 328D LCR excavator. It lists the required tools and gives step-by-step instructions to remove parts like the final drive cover, gears, carrier assemblies, planetary gear assemblies, and ring gear. Detailed illustrations are provided to show how to remove each component, and notes on weights and cleaning are included. The overall process involves using various tools to remove fasteners and separate the final drive into its individual parts.
Caterpillar cat 345 c l hydraulic excavator (prefix gcl) service repair manua...hhfjksekmm
The document provides step-by-step instructions for disassembling the final drive of a 345C excavator. It begins by having the reader remove the final drive and coupling. They are then instructed to disassemble the multiple internal components of the final drive including the carrier assemblies, planetary gears, and sprocket housing. Detailed illustrations accompany each step to show how to remove over 30 individual parts like retainers, shafts, seals and gears from the final drive.
This document provides instructions for disassembling and assembling the travel motor of 326D2 and 326D2 L excavators. The disassembly procedure involves removing 28 different components of the travel motor including the head, port plate, bearings, brake piston, plates, friction discs, and seals. The assembly procedure instructs putting the travel motor back together in the reverse order and notes the importance of cleanliness, applying lubricant to parts, and ensuring correct alignment of components.
Caterpillar cat 326 d2 l excavator (prefix jfl) service repair manual (jfl000...fjsekdmmeed
This document provides instructions for disassembling and assembling the travel motor of an excavator model 326D2 L. The disassembly procedure involves removing 28 different components of the travel motor in sequential order, including the head, port plate, springs, brake piston, plates, seals, and housing cover. The assembly procedure instructs installing these same components in reverse order, noting that all seals and gaskets must be replaced and components cleaned before assembly. Proper alignment and torque specifications are identified.
1) The document provides disassembly instructions for the final drive on 325 and 325L excavators. It describes removing over 30 parts in multiple steps, requiring various tools.
2) Key steps include removing the final drive cover, ring gear, carrier assemblies, planetary gears, seals, and bearings from the main housing. Detailed illustrations supplement each step.
3) Cleanliness is important during disassembly to prevent dirt from entering the mechanism. Parts must be reinstalled in their original locations and orientations.
Caterpillar cat 325 c excavator (prefix jld) service repair manual (jld00001 ...fjkskedmme
The document provides instructions for disassembling a final drive component from an excavator. It lists the required tools and gives step-by-step instructions to remove the final drive housing, gears, shafts, seals, and other internal parts. Detailed illustrations accompany each step. Disassembly involves removing retaining rings, gears, shafts, bearings, seals, and other parts from the housing using various tools, including a press, hammer, and pullers. Cleanliness is emphasized to prevent dirt from entering during disassembly.
Caterpillar cat 325 c l excavator (prefix bmm) service repair manual (bmm0000...fjkskedmme
The document provides step-by-step instructions to disassemble a final drive assembly for 325C and 325C L excavators. It begins by removing the final drive from the machine and securing it to a repair stand. Various gears, seals, bearings and housings are then removed through 32 numbered steps. Cleanliness is emphasized to prevent dirt from entering components. Tools required are listed in a table.
Caterpillar cat 328 d lcr excavator (prefix gtn) service repair manual (gtn00...fjsekdmmeed
The document provides instructions for disassembling the final drive of a 328D LCR excavator. It lists the required tools and presents a step-by-step process to remove parts such as gears, shafts, bearings, seals, and housings. Detailed illustrations accompany each step to show how to properly disassemble the various components using specialized tools like link brackets, forcing bolts, and pullers. The goal is to fully separate all parts of the final drive assembly for maintenance or repair purposes.
Caterpillar cat 328 d lcr excavator (prefix mkr) service repair manual (mkr00...fjsekdmmeed
The document provides instructions for disassembling the final drive of a 328D LCR excavator. It lists the required tools and gives step-by-step instructions to remove parts like the final drive cover, gears, carrier assemblies, planetary gear assemblies, and ring gear. Detailed illustrations are provided to show how to remove each component, and notes on weights and cleaning are included. The overall process involves using various tools to remove fasteners and separate the final drive into its individual parts.
Caterpillar cat 345 c l hydraulic excavator (prefix gcl) service repair manua...hhfjksekmm
The document provides step-by-step instructions for disassembling the final drive of a 345C excavator. It begins by having the reader remove the final drive and coupling. They are then instructed to disassemble the multiple internal components of the final drive including the carrier assemblies, planetary gears, and sprocket housing. Detailed illustrations accompany each step to show how to remove over 30 individual parts like retainers, shafts, seals and gears from the final drive.
This document provides instructions for disassembling and assembling the travel motor of 326D2 and 326D2 L excavators. The disassembly procedure involves removing 28 different components of the travel motor including the head, port plate, bearings, brake piston, plates, friction discs, and seals. The assembly procedure instructs putting the travel motor back together in the reverse order and notes the importance of cleanliness, applying lubricant to parts, and ensuring correct alignment of components.
Caterpillar cat 326 d2 l excavator (prefix jfl) service repair manual (jfl000...fjsekdmmeed
This document provides instructions for disassembling and assembling the travel motor of an excavator model 326D2 L. The disassembly procedure involves removing 28 different components of the travel motor in sequential order, including the head, port plate, springs, brake piston, plates, seals, and housing cover. The assembly procedure instructs installing these same components in reverse order, noting that all seals and gaskets must be replaced and components cleaned before assembly. Proper alignment and torque specifications are identified.
1) The document provides disassembly instructions for the final drive on 325 and 325L excavators. It describes removing over 30 parts in multiple steps, requiring various tools.
2) Key steps include removing the final drive cover, ring gear, carrier assemblies, planetary gears, seals, and bearings from the main housing. Detailed illustrations supplement each step.
3) Cleanliness is important during disassembly to prevent dirt from entering the mechanism. Parts must be reinstalled in their original locations and orientations.
Claas arion 640 c (type a20) tractor service repair manualikdkkdmdmdm
1) The document provides instructions for inspecting, measuring, and removing/refitting various cylinder head and valve components of an Arion 630-610 C engine, including the cylinder head, valves, rockers, turbocharger, alternator, fan hub, and exhaust manifold.
2) Specified values are provided for dimensions, clearances, and torque specifications to use when inspecting wear limits and refitting components.
3) Detailed steps and diagrams illustrate the procedures, such as marking parts for refitting, measuring valve and guide diameters, checking spring tension, and loosening bolts in a particular order for removal.
Claas arion 640 (type a19) tractor service repair manualikdkkdmdmdm
The document provides instructions for inspecting, removing, and refitting various components of the cylinder head and valves for an Arion 640-510 engine, including:
- Inspecting valve bridges, rocker pins, rockers, and measuring valve shrinkage, cylinder head flatness, and thickness.
- Procedures for removing and refitting the alternator, fan hub, turbocharger, exhaust manifold, EGR cooler, thermostat cover, and cylinder head cover.
- Specifications are provided for valve guides, springs, valves, and clearances between components.
Claas arion 630 c (type a20) tractor service repair manualikdkkdmdmdm
1) The document provides instructions for inspecting, measuring, and removing/refitting various cylinder head and valve components of an Arion 630-610 C engine, including the cylinder head, valves, rockers, turbocharger, alternator, fan hub, and exhaust manifold.
2) Specified values are provided for dimensions, clearances, and torque specifications to use when inspecting wear limits and refitting components.
3) Detailed steps and diagrams illustrate the procedures, such as marking parts for refitting, measuring valve and guide diameters, checking spring tension, and loosening bolts in a particular order for removal.
Claas arion 630 (type a19) tractor service repair manualikdkkdmdmdm
The document provides instructions for inspecting, removing, and refitting various components of the cylinder head and valves for an Arion 640-510 engine, including the cylinder head cover, rockers, valves, guides, springs, manifold, thermostat cover, and more. Dimensions and specifications are provided for clearances, diameters, wear limits, tensions, and torques. Images and part labels accompany each section.
Claas arion 620 c (type a20) tractor service repair manualikdkkdmdmdm
- The document provides instructions for inspecting and servicing various components of the cylinder head and valves for an Arion 630-610 C engine, including the rocker assembly, valves, springs, guides, seats, and cylinder head.
- The procedures include measuring component dimensions and clearances, checking for wear limits, removing and refitting parts, and adjusting the valve rockers. Tolerances and specifications are provided for inspecting parts and determining whether replacement is needed.
- The valve rockers are adjusted with the engine cold, using tools to position cylinder 1 at top dead center of compression and checking/adjusting rocker clearance for the appropriate valves.
Claas arion 620 (type a19) tractor service repair manualikdkkdmdmdm
The document provides instructions for inspecting, removing, and refitting various components of the cylinder head and valves for an Arion 640-510 engine, including:
- Inspecting valve bridges, rocker pins, rockers, and measuring valve shrinkage, cylinder head flatness, and thickness.
- Procedures for removing and refitting the alternator, fan hub, turbocharger, exhaust manifold, EGR cooler, thermostat cover, and cylinder head cover.
- Specifications are provided for valve guides, springs, valves, and clearances between components.
Claas arion 610 c (type a20) tractor service repair manualikdkkdmdmdm
- The document provides instructions for inspecting, measuring, removing, and refitting various components of the cylinder head and valves for an Arion 630-610 C engine, including the cylinder head, valves, rocker assembly, turbocharger, exhaust manifold, thermostat cover, and cylinder head cover.
- Specific measurements and tolerances are provided for components like the valve guides, springs, seats, and stems.
- The procedure for adjusting the valve rockers is described, which should be done on a cold engine with specific pistons at top dead center.
Claas arion 610 (type a19) tractor service repair manualikdkkdmdmdm
1) The document provides instructions for inspecting, measuring, and removing/refitting various components of the cylinder head and valves of an Arion 640-510 engine, including the valve bridges, rocker pins, rockers, valves, springs, cylinder head, guides, seats, and turbocharger.
2) Dimensions and specifications are provided for comparing wear limits and clearances. Instructions specify cleaning, marking, and replacing worn parts.
3) Procedures are described for removing and refitting the alternator, viscous coupling, fan hub, and turbocharger, noting torque specifications for fasteners.
Claas arion 600 c (type a20) tractor service repair manualikdkkdmdmdm
- The document provides instructions for inspecting and servicing various components of the cylinder head and valves for an Arion 630-610 C engine, including the rocker assembly, valves, springs, guides, seats, and cylinder head.
- The procedures include measuring component dimensions and clearances, checking for wear limits, removing and refitting parts, and adjusting the valve rockers. Tolerances and specifications are provided for inspecting parts and determining whether replacement is needed.
- The valve rockers are adjusted with the engine cold, using tools to position cylinder 1 at top dead center of compression and checking/adjusting rocker clearance for the specified valves.
Claas arion 600 (type a19) tractor service repair manualikdkkdmdmdm
1) The document provides instructions for inspecting, measuring, and removing/refitting various components of the cylinder head and valves of an Arion 640-510 engine, including the valve bridges, rocker pins, rockers, valves, springs, cylinder head, guides, seats, and turbocharger.
2) Dimensions and specifications are provided for comparing wear limits and clearances. Instructions specify cleaning, marking, and replacing worn parts.
3) The removal and refitting process for several accessories is described, including the alternator, viscous coupling, fan hub, and turbocharger. Torque specifications and notes about thread direction are included.
Claas arion 540 510 (type a18) tractor service repair manualikdkkdmdmdm
The document provides instructions for servicing components of the cylinder head and valves for an Arion 640-510 engine. It describes how to inspect, measure, and replace various parts including the cylinder head, valves, valve guides, springs, rockers, and related components. Procedures are outlined for removing and refitting the cylinder head cover, thermostat cover and manifold, exhaust manifold, turbocharger, and other parts. Tolerances and specifications are provided to check wear limits and clearances.
The helical drive pinion is supported by two tapered bearings mounted opposite each other within the rear axle housing. Its position is adjusted via shims located between the handbrake casing and housing. The bearings are preloaded by shims fitted between the bearing cone and thrust washer.
To service the drive pinion, the tractor must be uncoupled between the gearbox and rear axle. Then various components like the PTO clutch and four-wheel drive shaft must be removed to access the drive pinion. The nut securing the drive pinion is then removed along with other components to separate the drive pinion from the handbrake casing.
Proper adjustment of the drive pinion position
The document provides information on the technology of various non-moving and moving parts of an engine, including the engine block, wet liner, cylinder head, valves, piston rings, balance shaft, and other components. It describes features such as the cavity for the oil cooler in the engine block, slope of the upper flange between the liner and block, cross-flow design of the cylinder head, and helical groove on the valve guides for lubrication. Tightening torques are also provided for various engine fasteners.
Caterpillar cat 325 d excavator (prefix cyw) service repair manual (cyw00001 ...ikdkkdmdmdm
The document provides step-by-step instructions for assembling a hydraulic pump. It lists 61 steps involving the installation of gaskets, seals, pins, plates, pistons, shafts, bearings, covers, and other components into the pump housing in the correct order and orientation. Special tools and safety precautions are noted. The process concludes by installing the completed pump control and connecting fittings.
Caterpillar cat 325 c l excavator (prefix jld) service repair manual (jld0000...ikdkkdmdmdm
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and disassemble components of the final drive such as gears, carriers, shafts, and housings. Cleanliness is emphasized throughout. The assembly procedure is a reversal of the disassembly steps and involves applying sealants and lubricants to components before reinstalling them.
Caterpillar cat 325 c l excavator (prefix jlc) service repair manual (jlc0000...ikdkkdmdmdm
The document provides instructions for removing and installing a crankshaft wear sleeve and crankshaft gear on a 325C excavator. It describes using various tools to distort and remove the existing wear sleeve and install a new one. It also explains how to position a woodruff key and heat the crankshaft gear before installing it on the crankshaft. The document provides step-by-step instructions and illustrations for the procedures.
Caterpillar cat 325 c l excavator (prefix bmm) service repair manual (bmm0000...ikdkkdmdmdm
The document provides instructions to disassemble a final drive assembly. Key steps include:
1. Marking the final drive for alignment and removing it from the machine.
2. Removing the cover, gears, carriers, and housing components using various tools.
3. Disassembling the internal gears and carriers into individual parts like shafts, pins, washers.
4. Cleaning parts thoroughly before inspection and replacement of any worn components.
Caterpillar cat 325 c l excavator (prefix bkw) service repair manual (bkw0000...ikdkkdmdmdm
This document provides instructions for disassembling and assembling the final drive of a 325C excavator. The disassembly procedure involves removing over 30 individual parts from the final drive housing. The assembly procedure instructs technicians to clean all parts thoroughly, apply lubricants, and install parts in the reverse order of disassembly. Technicians are advised to replace all seals and gaskets during assembly and to measure bearing clearances at specific steps.
Caterpillar cat 325 c l excavator (prefix amh) service repair manual (amh0000...ikdkkdmdmdm
The document provides instructions for removing and installing various engine components on a Caterpillar 3126B engine, including:
- Camshaft removal which requires removing the lifter group and front cover before removing the camshaft, camshaft retainer plate, and bolts.
- Camshaft bearing removal using a special tool and noting the oil hole orientation for installation.
- Engine oil pan removal by draining the oil, removing bolts and drain plug, and cleaning the mating surfaces before installing with a new gasket using sealant on the joints.
Caterpillar cat 325 c fm excavator (prefix y4p) service repair manual (y4p000...ikdkkdmdmdm
This document provides instructions for disassembling and assembling the final drive of a 325C FM excavator. It lists the required tools and presents step-by-step procedures with illustrations. The procedures include removing components such as sprockets, gears, seals, and bearings. A special bench is used to remove the locknut requiring hydraulic pressure up to 2000 psi. Reassembly follows the reverse order of disassembly.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Claas arion 640 c (type a20) tractor service repair manualikdkkdmdmdm
1) The document provides instructions for inspecting, measuring, and removing/refitting various cylinder head and valve components of an Arion 630-610 C engine, including the cylinder head, valves, rockers, turbocharger, alternator, fan hub, and exhaust manifold.
2) Specified values are provided for dimensions, clearances, and torque specifications to use when inspecting wear limits and refitting components.
3) Detailed steps and diagrams illustrate the procedures, such as marking parts for refitting, measuring valve and guide diameters, checking spring tension, and loosening bolts in a particular order for removal.
Claas arion 640 (type a19) tractor service repair manualikdkkdmdmdm
The document provides instructions for inspecting, removing, and refitting various components of the cylinder head and valves for an Arion 640-510 engine, including:
- Inspecting valve bridges, rocker pins, rockers, and measuring valve shrinkage, cylinder head flatness, and thickness.
- Procedures for removing and refitting the alternator, fan hub, turbocharger, exhaust manifold, EGR cooler, thermostat cover, and cylinder head cover.
- Specifications are provided for valve guides, springs, valves, and clearances between components.
Claas arion 630 c (type a20) tractor service repair manualikdkkdmdmdm
1) The document provides instructions for inspecting, measuring, and removing/refitting various cylinder head and valve components of an Arion 630-610 C engine, including the cylinder head, valves, rockers, turbocharger, alternator, fan hub, and exhaust manifold.
2) Specified values are provided for dimensions, clearances, and torque specifications to use when inspecting wear limits and refitting components.
3) Detailed steps and diagrams illustrate the procedures, such as marking parts for refitting, measuring valve and guide diameters, checking spring tension, and loosening bolts in a particular order for removal.
Claas arion 630 (type a19) tractor service repair manualikdkkdmdmdm
The document provides instructions for inspecting, removing, and refitting various components of the cylinder head and valves for an Arion 640-510 engine, including the cylinder head cover, rockers, valves, guides, springs, manifold, thermostat cover, and more. Dimensions and specifications are provided for clearances, diameters, wear limits, tensions, and torques. Images and part labels accompany each section.
Claas arion 620 c (type a20) tractor service repair manualikdkkdmdmdm
- The document provides instructions for inspecting and servicing various components of the cylinder head and valves for an Arion 630-610 C engine, including the rocker assembly, valves, springs, guides, seats, and cylinder head.
- The procedures include measuring component dimensions and clearances, checking for wear limits, removing and refitting parts, and adjusting the valve rockers. Tolerances and specifications are provided for inspecting parts and determining whether replacement is needed.
- The valve rockers are adjusted with the engine cold, using tools to position cylinder 1 at top dead center of compression and checking/adjusting rocker clearance for the appropriate valves.
Claas arion 620 (type a19) tractor service repair manualikdkkdmdmdm
The document provides instructions for inspecting, removing, and refitting various components of the cylinder head and valves for an Arion 640-510 engine, including:
- Inspecting valve bridges, rocker pins, rockers, and measuring valve shrinkage, cylinder head flatness, and thickness.
- Procedures for removing and refitting the alternator, fan hub, turbocharger, exhaust manifold, EGR cooler, thermostat cover, and cylinder head cover.
- Specifications are provided for valve guides, springs, valves, and clearances between components.
Claas arion 610 c (type a20) tractor service repair manualikdkkdmdmdm
- The document provides instructions for inspecting, measuring, removing, and refitting various components of the cylinder head and valves for an Arion 630-610 C engine, including the cylinder head, valves, rocker assembly, turbocharger, exhaust manifold, thermostat cover, and cylinder head cover.
- Specific measurements and tolerances are provided for components like the valve guides, springs, seats, and stems.
- The procedure for adjusting the valve rockers is described, which should be done on a cold engine with specific pistons at top dead center.
Claas arion 610 (type a19) tractor service repair manualikdkkdmdmdm
1) The document provides instructions for inspecting, measuring, and removing/refitting various components of the cylinder head and valves of an Arion 640-510 engine, including the valve bridges, rocker pins, rockers, valves, springs, cylinder head, guides, seats, and turbocharger.
2) Dimensions and specifications are provided for comparing wear limits and clearances. Instructions specify cleaning, marking, and replacing worn parts.
3) Procedures are described for removing and refitting the alternator, viscous coupling, fan hub, and turbocharger, noting torque specifications for fasteners.
Claas arion 600 c (type a20) tractor service repair manualikdkkdmdmdm
- The document provides instructions for inspecting and servicing various components of the cylinder head and valves for an Arion 630-610 C engine, including the rocker assembly, valves, springs, guides, seats, and cylinder head.
- The procedures include measuring component dimensions and clearances, checking for wear limits, removing and refitting parts, and adjusting the valve rockers. Tolerances and specifications are provided for inspecting parts and determining whether replacement is needed.
- The valve rockers are adjusted with the engine cold, using tools to position cylinder 1 at top dead center of compression and checking/adjusting rocker clearance for the specified valves.
Claas arion 600 (type a19) tractor service repair manualikdkkdmdmdm
1) The document provides instructions for inspecting, measuring, and removing/refitting various components of the cylinder head and valves of an Arion 640-510 engine, including the valve bridges, rocker pins, rockers, valves, springs, cylinder head, guides, seats, and turbocharger.
2) Dimensions and specifications are provided for comparing wear limits and clearances. Instructions specify cleaning, marking, and replacing worn parts.
3) The removal and refitting process for several accessories is described, including the alternator, viscous coupling, fan hub, and turbocharger. Torque specifications and notes about thread direction are included.
Claas arion 540 510 (type a18) tractor service repair manualikdkkdmdmdm
The document provides instructions for servicing components of the cylinder head and valves for an Arion 640-510 engine. It describes how to inspect, measure, and replace various parts including the cylinder head, valves, valve guides, springs, rockers, and related components. Procedures are outlined for removing and refitting the cylinder head cover, thermostat cover and manifold, exhaust manifold, turbocharger, and other parts. Tolerances and specifications are provided to check wear limits and clearances.
The helical drive pinion is supported by two tapered bearings mounted opposite each other within the rear axle housing. Its position is adjusted via shims located between the handbrake casing and housing. The bearings are preloaded by shims fitted between the bearing cone and thrust washer.
To service the drive pinion, the tractor must be uncoupled between the gearbox and rear axle. Then various components like the PTO clutch and four-wheel drive shaft must be removed to access the drive pinion. The nut securing the drive pinion is then removed along with other components to separate the drive pinion from the handbrake casing.
Proper adjustment of the drive pinion position
The document provides information on the technology of various non-moving and moving parts of an engine, including the engine block, wet liner, cylinder head, valves, piston rings, balance shaft, and other components. It describes features such as the cavity for the oil cooler in the engine block, slope of the upper flange between the liner and block, cross-flow design of the cylinder head, and helical groove on the valve guides for lubrication. Tightening torques are also provided for various engine fasteners.
Caterpillar cat 325 d excavator (prefix cyw) service repair manual (cyw00001 ...ikdkkdmdmdm
The document provides step-by-step instructions for assembling a hydraulic pump. It lists 61 steps involving the installation of gaskets, seals, pins, plates, pistons, shafts, bearings, covers, and other components into the pump housing in the correct order and orientation. Special tools and safety precautions are noted. The process concludes by installing the completed pump control and connecting fittings.
Caterpillar cat 325 c l excavator (prefix jld) service repair manual (jld0000...ikdkkdmdmdm
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and disassemble components of the final drive such as gears, carriers, shafts, and housings. Cleanliness is emphasized throughout. The assembly procedure is a reversal of the disassembly steps and involves applying sealants and lubricants to components before reinstalling them.
Caterpillar cat 325 c l excavator (prefix jlc) service repair manual (jlc0000...ikdkkdmdmdm
The document provides instructions for removing and installing a crankshaft wear sleeve and crankshaft gear on a 325C excavator. It describes using various tools to distort and remove the existing wear sleeve and install a new one. It also explains how to position a woodruff key and heat the crankshaft gear before installing it on the crankshaft. The document provides step-by-step instructions and illustrations for the procedures.
Caterpillar cat 325 c l excavator (prefix bmm) service repair manual (bmm0000...ikdkkdmdmdm
The document provides instructions to disassemble a final drive assembly. Key steps include:
1. Marking the final drive for alignment and removing it from the machine.
2. Removing the cover, gears, carriers, and housing components using various tools.
3. Disassembling the internal gears and carriers into individual parts like shafts, pins, washers.
4. Cleaning parts thoroughly before inspection and replacement of any worn components.
Caterpillar cat 325 c l excavator (prefix bkw) service repair manual (bkw0000...ikdkkdmdmdm
This document provides instructions for disassembling and assembling the final drive of a 325C excavator. The disassembly procedure involves removing over 30 individual parts from the final drive housing. The assembly procedure instructs technicians to clean all parts thoroughly, apply lubricants, and install parts in the reverse order of disassembly. Technicians are advised to replace all seals and gaskets during assembly and to measure bearing clearances at specific steps.
Caterpillar cat 325 c l excavator (prefix amh) service repair manual (amh0000...ikdkkdmdmdm
The document provides instructions for removing and installing various engine components on a Caterpillar 3126B engine, including:
- Camshaft removal which requires removing the lifter group and front cover before removing the camshaft, camshaft retainer plate, and bolts.
- Camshaft bearing removal using a special tool and noting the oil hole orientation for installation.
- Engine oil pan removal by draining the oil, removing bolts and drain plug, and cleaning the mating surfaces before installing with a new gasket using sealant on the joints.
Caterpillar cat 325 c fm excavator (prefix y4p) service repair manual (y4p000...ikdkkdmdmdm
This document provides instructions for disassembling and assembling the final drive of a 325C FM excavator. It lists the required tools and presents step-by-step procedures with illustrations. The procedures include removing components such as sprockets, gears, seals, and bearings. A special bench is used to remove the locknut requiring hydraulic pressure up to 2000 psi. Reassembly follows the reverse order of disassembly.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR JLD
Configuration: 325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
325C Excavator Machine Systems
Media Number -RENR5367-11 Publication Date -01/01/2012 Date Updated -17/02/2017
i05453056
Final Drive - Remove
SMCS - 4050-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8S-7611 Handle As 2
8S-7615 Pin As 2
283-1495 Stand Assembly 2
B 439-3939 Link Bracket As 2
C
154-6184 Forcing Bolt (M 20) 2
154-6185(1)
Forcing Bolt (M 24) 2
(1)
For Use on 329 and 330 sales models
Start By:
a. Separate the track assembly.
b. Remove the travel motor.
1/3
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. Illustration 1 g00489826
Typical Example
Note: Adjust the height of Tooling (A) so that there is sufficient clearance between the
sprocket and the track for the removal of the final drive.
1. Lift the side of the machine in order to install Tooling (A) under the frame, as shown.
Illustration 2 g00712767
2. Fasten Tooling (B) and a suitable lifting device to final drive (1), as shown. Put a slight
lifting tension on the final drive.
Illustration 3 g00712737
2/3
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Note: Mark the orientation of bolt holes (2) for the travel motor for installation purposes.
3. Remove bolts (3) and the washers from the final drive.
Illustration 4 g00712749
4. Use Tooling (C) in order to remove the final drive from the frame.
5. Carefully remove final drive (1). The weight of final drive (1) and the sprocket is
approximately 312 kg (688 lb).
6. Remove Tooling (C) from the frame.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jul 8 00:51:28 UTC+0800 2020
3/3
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR JLD
Configuration: 325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
325C Excavator Machine Systems
Media Number -RENR5367-11 Publication Date -01/01/2012 Date Updated -17/02/2017
i04758849
Final Drive - Disassemble
SMCS - 4050-015
Disassembly Procedure (227-6116)
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 138-7573 Link Bracket 2
C 1P-1863 Retaining Ring Pliers 1
D 194-3878 Spanner Socket 1
E 138-7574 Link Bracket 2
F
5F-7366 Forcing Screw 1
1P-5546 Crossblock 1
1U-9889 Crossblock 1
1P-0520 Driver Group 1
6V-7888 Puller Leg 2
1H-3112 Puller Assembly 1
1P-5551 Adjustable Screw Assembly 1
G
1U-7600 Slide Hammer Puller Gp 1
8T-0266 Bolt 1
1/13
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Start By:
A. Remove the final drive. Refer to Disassembly and Assembly, "Final Drive - Remove".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of
the component should be thoroughly cleaned. This will prevent dirt from entering the
internal mechanism.
Note: Some of the images that are in this procedure do not show the sprocket assembly that
is attached to the final drive housing. If necessary, the weights that are given include the
weight of the sprocket assembly.
1. Put an alignment mark across the sections of the final drive for assembly purposes. The
parts must be reinstalled in the part's original locations.
Illustration 1 g00708089
2. Fasten the final drive to Tooling (A), as shown. The weight of the final drive assembly is
approximately 312 kg (688 lb).
3. Remove bolts (1) and the washers that hold the cover in position.
Illustration 2 g00708090
2/13
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. 4. Remove the setscrews from the cover. Fasten Tooling (B) and a suitable lifting device to
cover (2), as shown. Remove the cover. The weight of the cover is approximately 32 kg (70
lb).
Illustration 3 g00879362
5. Remove bolts (3). Remove gear (5). Check plate (6). Replace plate (6) if wear is shown.
Remove plugs (4) from cover (2) .
Illustration 4 g00879365
6. Remove O-ring seal (7) from plugs (4) .
3/13
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Illustration 5 g00780428
7. Remove gear (8). Remove spacer (9) .
Illustration 6 g00780432
8. Remove retaining ring (10) with Tooling (C). Remove washer (11). Remove gear (12).
Remove bearing assembly (13). Remove second washer (11) .
9. Repeat Step 8 for the remaining two gear assemblies.
4/13
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Illustration 7 g00781401
10. Remove retaining ring (14) .
Illustration 8 g00781407
11. Remove carrier assembly (15) .
Illustration 9 g01389593
12. Use a suitable press in order to remove the shafts from carrier assembly (15) .
5/13
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. 16. Disassemble carrier assembly (19), as follows.
a. Drive spring pin (20) into planetary shaft (21) with a hammer and a punch.
Illustration 13 g00781476
b. Remove planetary shaft (21) .
c. Remove spring pin (20) from planetary shaft (21) with a hammer and a punch.
Illustration 14 g00781516
d. Remove thrust washers (22) and planetary gear (24) from the carrier assembly.
e. Remove bearing (23) from planetary gear (24) .
17. Repeat Steps 16.a through 16.e for the other two planetary.
7/13
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. Illustration 15 g00781529
18. Remove gear (25). Remove spacer (26) .
Illustration 16 g00781559
19. Remove carrier assembly (27) .
20. Use two people to remove carrier assembly (27). The weight of the carrier assembly is
approximately 38 kg (85 lb).
21. Disassemble carrier assembly (27), as follows.
8/13
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Illustration 17 g00781719
a. Drive spring pin (29) into planetary shaft (28) with a hammer and a punch.
Illustration 18 g00781601
b. Remove planetary shaft (28) .
c. Remove spring pin (29) from planetary shaft (28) with a hammer and a punch.
Illustration 19 g00781607
d. Remove thrust washers (30) and planetary gear (32) from the carrier assembly.
e. Remove two bearings (31) from the planetary gear.
22. Repeat Steps 21.a through 21.e for the other two planetary gears.
9/13
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Illustration 20 g00781730
23. Use two people to remove gear (33). The weight of gear is approximately 41 kg (90 lb).
Illustration 21 g00781807
24. Remove O-ring seal (34) .
Illustration 22 g01147650
25. Remove bolts (35A) and plates (35B) .
10/13
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engi...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Illustration 23 g01147651
26. Use Tooling (G) to remove dowel (37) from stopper plate (35) .
Illustration 24 g01147759
27. Secure Tooling (D) to stopper plate (35). Use Tooling (D) to remove stopper plate (35) .
11/13
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engi...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Illustration 25 g01147930
28. Use Tooling (E) and a suitable lifting device to remove housing (36). The weight of housing
(36) is approximately 100 kg (220 lb).
Illustration 26 g01147951
29. Remove Duo-Cone seal (39A) from housing (38) .
Illustration 27 g01147975
12/13
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engi...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Illustration 28 g01147934
30. Remove Duo-Cone seal (39B) from housing (36) .
31. Use Tooling (F) in order to remove bearings (40) and (41) from housing (36) .
32. If necessary, remove the final drive sprocket from the sprocket housing. Refer to
Disassembly and Assembly, "Final Drive Sprocket - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jul 8 00:52:24 UTC+0800 2020
13/13
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engi...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR JLD
Configuration: 325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
325C Excavator Machine Systems
Media Number -RENR5367-11 Publication Date -01/01/2012 Date Updated -17/02/2017
i04758848
Final Drive - Assemble
SMCS - 4050-016
Assembly Procedure (227-6116)
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 138-7573 Link Bracket 2
C 1P-1863 Retaining Ring Pliers 1
D
194-3878 Spanner Wrench As 1
194-3884 Spacer 1
E 138-7574 Link Bracket 2
H 6V-7030 Micrometer Depth Gauge Group 1
J FT-2770 Leak Down Test Tool 1
K 1U-6396 O-Ring Assembly Compound 1
L 5P-3931 Anti-Seize Compound 1
M 1U-8846 Gasket Sealant 1
N 8T-0531 Duo-Cone Seal Installer As 1
P 5P-3931 Anti-Seize Compound 1
Q 240-1886 Drill Fixture Gp 1
R 9S-3263 Thread Lock Compound 1
1/19
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Note: Cleanliness is an important factor. Before assembly, clean all parts thoroughly in cleaning
fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be
deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or
damaged, use new parts for replacement. All disassembly and all assembly procedures must be
performed on a clean work surface and in a clean hydraulic area. Keep cleaned parts covered and
protected at all times.
Note: O-ring seals, gaskets, and seals should always be replaced. A used O-ring seal may not have
the same sealing properties as a new O-ring. Use Tooling (K) during the assembly procedure.
Note: Apply a light film of hydraulic oil to all components before assembly.
Note: Some of the images that are in this procedure do not show the sprocket assembly that is
attached to the final drive housing. If necessary, the weights that are given include the weight of
the sprocket assembly.
Illustration 1 g01147975
1. Apply Tooling (P) to the outer diameter of the bearings.
2. Use a suitable press to Install bearings (40) and (41). Make sure that bearing (41) and
bearing (40) contact the counterbore in housing (36) .
3. Use Tooling (N) to install Duo-Cone seal (39B) .
2/19
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. Illustration 2 g01147981
4. Use Tooling (N) to install Duo-Cone seal (39A) onto housing (38).
Illustration 3 g01147930
5. Use Tooling (E) and a suitable lifting device to install housing (36) onto housing (38). The
weight of housing (36) is approximately 100 kg (220 lb).
6. Remove Tooling (E) from housing (36) .
3/19
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. Illustration 4 g01147724
7. Install stopper plate (35). Do not tighten stopper plate assembly (35) at this time.
Note: Stopper plate (35) will secure housing (36) to housing (38) .
8. Install Tooling (E) and a suitable lifting device to housing (36). The combined weight of
housing assembly (36) and (38) is approximately 120 kg (265 lb). Install housing assembly
(36) and (38) in a suitable press.
9. Remove stopper plate (35) .
Illustration 5 g01147727
10. Assemble Tooling (D), as shown.
Illustration 6 g01147731
11. Install Tooling (D) into housing (36), as shown.
12. Apply a force of 4000 kg (8818 lb) to the top of Tooling (D). Rotate housing (36) in order to
seat the bearings.
13. Reduce the force on the top of Tooling (D) to 1000 kg (2205 lb).
4/19
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Illustration 7 g01147737
14. Use Tooling (H) to take a measurement in three locations. Average the three measurements
and record the average measurement as Dimension (W) .
15. Remove Tooling (D) .
16. Separate Tooling (D) .
Illustration 8 g01147743
17. Use a micrometer in order to measure the thickness at three locations of the spacer from
Tooling (D). Record the average measurement as Dimension (X) .
5/19
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Illustration 9 g01147742
18. Use a micrometer in order to measure the thickness at three locations of stopper plate (35).
Record the average measurement as Dimension (Y) .
19. Subtract Dimension (X) from Dimension (Y) and record this figure as Dimension (Z) .
Illustration 10 g01147724
20. Install stopper plate (35) onto housing (38). Do not tighten stopper plate (35) at this time.
Stopper plate (35) will secure the final drive assembly while the final drive assembly is
repositioned onto Tooling (A) .
21. Use Tooling (E) and a suitable lifting device to reposition the final drive assembly onto
Tooling (A). The combined weight of housing assembly (36) and (38) is approximately 120
kg (265 lb).
22. Secure the final drive assembly to Tooling (A) .
6/19
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Illustration 11 g01148004
23. Secure the spanner socket from Tooling (D) to stopper plate (35) .
24. In order to determine the final bearing preload, add Dimension (W) to Dimension (Z) and
record this figure as Dimension (V) .
25. Use Tooling (H) to measure the distance in three locations.
26. Tighten stopper plate (35) until the average of the measurements is equal to Dimension (V) .
27. Remove Tooling (D) .
Illustration 12 g01372092
28. Install Tooling (Q) and a suitable vacuum onto stopper plate (35) .
7/19
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
25. Illustration 13 g01147789
29. Use a suitable drill and Tooling (Q) in order to drill a hole to the depth of 15 mm (0.6 inch)
in the stopper palte and in housing (38) .
Illustration 14 g01147796
30. Install dowel (37) .
Illustration 15 g01147650
8/19
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
26. 31. Apply Tooling (R) on bolts (35A). Install plate (35B) and bolts (35A) .
32. Repeat Steps 28 through 31 for the opposite side of stopper plate (35) .
Illustration 16 g00781807
33. Install O-ring seal (34) on housing (36) .
Illustration 17 g00781730
34. Install gear (33) on housing (36).
9/19
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
27. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
28. Illustration 18 g00781719
35. Assemble carrier assembly (27), as follows.
Illustration 19 g00781607
a. Use a deburring tool in order to remove the metal burr from the openings in the
carrier.
b. Install two bearings (31) in planetary gear (32) .
c. Install thrust washers (30) and planetary gear (32) in the carrier assembly.
d. Install planetary shaft (28) in the carrier assembly.
e. Align the split in spring pin (29) to the top or to the bottom. Make a stake mark on
each side of the spring pin hole in the carrier. Each stake mark should be
approximately 1.50 mm (0.059 inch) from the outside diameter of the spring pin hole.
10/19
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engi...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
29. Illustration 20 g00903073
f. Drive spring pin (29) into planetary shaft (28) with a hammer and a punch.
36. Repeat Steps 35.a through 35.e in order to install the other two planetary gears in the carrier.
Illustration 21 g00781559
37. Use two people to install carrier assembly (27) in gear (33). The weight of carrier assembly
(27) is approximately 38 kg (85 lb).
11/19
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engi...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...