The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and install components like gears, carriers, seals, and housings. Cleanliness is emphasized and O-rings, gaskets, and seals should always be replaced. The assembly procedure is the reverse of the disassembly with notes to apply lubricants and check parts for wear.
Caterpillar cat 325 c excavator (prefix jld) service repair manual (jld00001 ...fjkskedmme
The document provides instructions for disassembling a final drive component from an excavator. It lists the required tools and gives step-by-step instructions to remove the final drive housing, gears, shafts, seals, and other internal parts. Detailed illustrations accompany each step. Disassembly involves removing retaining rings, gears, shafts, bearings, seals, and other parts from the housing using various tools, including a press, hammer, and pullers. Cleanliness is emphasized to prevent dirt from entering during disassembly.
Caterpillar cat 325 c excavator (prefix jld) service repair manual (jld00001 ...fjskeazqkkdmme
This document provides instructions for disassembling and assembling the final drive on 325C and 325C L excavator models. It gives detailed steps for removing the final drive unit from the machine and then disassembling it into individual components. These include removing gears, carriers, shafts, seals, and other parts. Precautions are outlined regarding cleanliness and lubrication. Required tools are listed. The assembly procedure then provides mirrored instructions for reassembling the final drive unit.
Caterpillar cat 325 c l excavator (prefix jld) service repair manual (jld0000...fjkskedmme
The document provides instructions for disassembling a final drive component from an excavator. It lists the required tools and gives step-by-step instructions to remove the final drive housing, gears, shafts, seals, and other internal parts. Detailed illustrations accompany each step. Disassembly involves removing retaining rings, gears, shafts, bearings, seals, and other parts from the housing using various tools, with attention to cleanliness and proper part labeling.
Caterpillar cat 325 c l excavator (prefix jld) service repair manual (jld0000...fjskeazqkkdmme
This document provides instructions for disassembling and assembling the final drive on 325C and 325C L excavator models. It gives detailed steps for removing the final drive from the machine, disassembling the internal components, and assembling the components back into the final drive housing. The procedures involve removing retaining rings, gears, shafts, seals, and other parts. Special tools are required and cleanliness is important when disassembling and assembling. Weights of removed parts are provided to assist with lifting.
Caterpillar Cat 325C and 325C L Excavator (Prefix BMM) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions to disassemble a final drive assembly. Key steps include:
1. Marking the final drive for alignment and removing it from the machine.
2. Removing the cover, gears, spacers, and carrier assemblies.
3. Disassembling the carrier assemblies by pressing out pins and removing gears and bearings.
4. Removing the ring gears from the main housing after lifting with slings.
Caterpillar Cat 325C and 325C L Excavator (Prefix BMM) Service Repair Manual ...zan2736ban
The document provides instructions to disassemble a final drive assembly. Key steps include:
1. Marking the final drive for alignment and removing it from the machine.
2. Removing the cover, gears, spacers, and carrier assemblies.
3. Disassembling the carrier assemblies by pressing out pins and removing gears and bearings.
4. Removing the ring gears from the main housing after lifting with slings.
This document provides instructions for disassembling and assembling components of a C27 Industrial Engine, including:
1. Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2. Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3. Removing and installing the valve mechanism cover base by removing tubes, harnesses, bolts, and installing seals and components.
This document provides instructions for disassembling and assembling axle shaft assemblies and brake groups for a 938F wheel loader. It describes removing and installing the front and rear axle housing groups. The procedures are the same for both groups. Key steps include removing retaining rings, planetary carrier assemblies, seals, and applying shop air to remove brake pistons. New seals and lubrication with SAE 30 oil are required for reassembly.
Caterpillar cat 325 c excavator (prefix jld) service repair manual (jld00001 ...fjkskedmme
The document provides instructions for disassembling a final drive component from an excavator. It lists the required tools and gives step-by-step instructions to remove the final drive housing, gears, shafts, seals, and other internal parts. Detailed illustrations accompany each step. Disassembly involves removing retaining rings, gears, shafts, bearings, seals, and other parts from the housing using various tools, including a press, hammer, and pullers. Cleanliness is emphasized to prevent dirt from entering during disassembly.
Caterpillar cat 325 c excavator (prefix jld) service repair manual (jld00001 ...fjskeazqkkdmme
This document provides instructions for disassembling and assembling the final drive on 325C and 325C L excavator models. It gives detailed steps for removing the final drive unit from the machine and then disassembling it into individual components. These include removing gears, carriers, shafts, seals, and other parts. Precautions are outlined regarding cleanliness and lubrication. Required tools are listed. The assembly procedure then provides mirrored instructions for reassembling the final drive unit.
Caterpillar cat 325 c l excavator (prefix jld) service repair manual (jld0000...fjkskedmme
The document provides instructions for disassembling a final drive component from an excavator. It lists the required tools and gives step-by-step instructions to remove the final drive housing, gears, shafts, seals, and other internal parts. Detailed illustrations accompany each step. Disassembly involves removing retaining rings, gears, shafts, bearings, seals, and other parts from the housing using various tools, with attention to cleanliness and proper part labeling.
Caterpillar cat 325 c l excavator (prefix jld) service repair manual (jld0000...fjskeazqkkdmme
This document provides instructions for disassembling and assembling the final drive on 325C and 325C L excavator models. It gives detailed steps for removing the final drive from the machine, disassembling the internal components, and assembling the components back into the final drive housing. The procedures involve removing retaining rings, gears, shafts, seals, and other parts. Special tools are required and cleanliness is important when disassembling and assembling. Weights of removed parts are provided to assist with lifting.
Caterpillar Cat 325C and 325C L Excavator (Prefix BMM) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions to disassemble a final drive assembly. Key steps include:
1. Marking the final drive for alignment and removing it from the machine.
2. Removing the cover, gears, spacers, and carrier assemblies.
3. Disassembling the carrier assemblies by pressing out pins and removing gears and bearings.
4. Removing the ring gears from the main housing after lifting with slings.
Caterpillar Cat 325C and 325C L Excavator (Prefix BMM) Service Repair Manual ...zan2736ban
The document provides instructions to disassemble a final drive assembly. Key steps include:
1. Marking the final drive for alignment and removing it from the machine.
2. Removing the cover, gears, spacers, and carrier assemblies.
3. Disassembling the carrier assemblies by pressing out pins and removing gears and bearings.
4. Removing the ring gears from the main housing after lifting with slings.
This document provides instructions for disassembling and assembling components of a C27 Industrial Engine, including:
1. Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2. Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3. Removing and installing the valve mechanism cover base by removing tubes, harnesses, bolts, and installing seals and components.
This document provides instructions for disassembling and assembling axle shaft assemblies and brake groups for a 938F wheel loader. It describes removing and installing the front and rear axle housing groups. The procedures are the same for both groups. Key steps include removing retaining rings, planetary carrier assemblies, seals, and applying shop air to remove brake pistons. New seals and lubrication with SAE 30 oil are required for reassembly.
This document provides instructions for removing and installing various components of a C27 Industrial Engine, including:
1. Removing the front gear group by removing bolts and gear assemblies.
2. Removing the front housing by removing covers, dampers, brackets, and bolts to detach the housing.
3. Removing the rear housing by removing elbow assemblies, bolts connecting the oil pan, and disconnecting hose assemblies.
1) The document provides instructions for removing and installing various components of a Caterpillar C9.3 industrial engine, including disconnecting snap-to-connect fittings, removing and installing a muffler, and removing and installing a fuel priming pump and fuel filter base.
2) The procedures include illustrations showing the components and numbered steps for disassembly and reassembly. Safety warnings are provided at the beginning regarding relieving pressures before disconnection.
3) Torque specifications and required tools are listed for relevant installation steps.
This document provides instructions for removing and installing various fuel system components on a Caterpillar C9 Industrial Engine, including:
- Removing and installing the fuel priming pump
- Removing and installing the fuel filter base
- Removing a unit injector from the engine cylinder head
The procedures describe draining fluids, using specialty tools to remove and install parts, cleaning components, lubricating seals, and torquing bolts to the specified values. Technicians are advised to take precautions to prevent spills and contamination when working on the fuel system.
This document provides instructions for disassembling and assembling components of a 938F wheel loader transmission. It describes removing the transmission from the vehicle and then disassembling it into individual parts like shafts, gears, seals, and clutches. The multi-step process includes using various tools to compress springs, remove snap rings, and disassemble interconnected sub-assemblies. Reassembly follows the reverse order and includes inspecting parts for wear and replacing as needed.
This document provides instructions for removing and installing an engine oil filter base and oil cooler from a Caterpillar C9 Industrial Engine. It describes:
- Draining the coolant from the cooling system before removal
- Using a strap wrench to remove the oil filter
- Disconnecting hoses and removing bolts to take off the oil filter base and oil cooler
- Cleaning and installing replacement parts in the reverse order
This document provides instructions for removing and installing various engine components on a Caterpillar C27 Industrial Engine, including:
1) Valves, springs, and related parts using specialized tools to compress springs.
2) Valve guides using a driver tool and ensuring proper height.
3) Valve seat inserts using an extractor tool and driver to install new inserts.
4) The engine oil filter base and related internal parts, noting any spring pressure hazards.
Caterpillar Cat 345D L Excavator (Prefix EEH) Service Repair Manual (EEH00001...jdkskmmdmd1
This document provides instructions for disassembling and assembling the final drive components of a 345D L Excavator. It describes removing 28 components in 28 steps, including the final drive cover, carrier assemblies, ring gear, and sprocket housing. Reassembly is described in 21 steps, beginning with installing bearing cups into the sprocket housing and ending by attaching the coupling to the motor housing. Tools required are listed.
This document provides instructions for removing and installing various engine components on a C27 Industrial Engine, including:
1) Inlet and exhaust valves, springs, and related parts.
2) Inlet and exhaust valve guides.
3) Inlet and exhaust valve seat inserts.
4) The engine oil filter base.
The procedures describe the required tools and provide illustrations showing the parts. Safety notices are included regarding spring-loaded components.
Caterpillar Cat 345C L Excavator (Prefix TBA) Service Repair Manual (TBA00001...jdkskmmdmd1
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, and brake piston. Identification marks should be made on parts for reassembly. To assemble, the document instructs reversing the 31 disassembly steps and notes that parts must be cleaned and reinstalled in their original locations and orientations.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual (KFH00001...jdkskmmdmd1
1. The document provides instructions for removing and installing the rear gear group and flywheel on a C13 engine.
2. It details the required tools and presents a step-by-step process with illustrations for disassembling, inspecting, and reassembling each component.
3. Special attention is given to bearing installation and torque specifications for fasteners.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1. Valves, valve guides, and valve seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2. The engine oil filter base, oil cooler, and oil pump. It emphasizes cleaning parts and contains fluids properly during removal and installation.
3. Safety precautions are provided, such as wearing protective equipment when working with spring-loaded parts and ensuring contaminants are avoided. Numerical sequences and specifications are given for installing certain parts correctly.
The document provides instructions for disassembling and assembling a travel motor. It is a 31 step process that includes removing components like the head, brake piston, disks, and seals. Tools required are listed. Cleanliness is emphasized to prevent contamination of hydraulic systems. Used parts should be replaced with new ones and marks made to ensure correct reinstallation of parts.
Massey Ferguson 1652 COMPACT TRACTORS Parts Catalogue Manual.pdfjdkskmmdmd1
This document is a table of contents for the engine, fuel, and exhaust systems of Massey Ferguson 1648, 1652, and 1655 compact tractors. It contains 91 pages listing component part numbers and references for the engine, fuel injection, cooling, exhaust, and related systems. The pages are organized by component and sub-components.
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, pins, plates, seals, pistons, disks, and bearings. The assembly procedure reverses the disassembly process in 30 steps and provides notes about cleaning parts, applying lubricant, and ensuring proper orientation of components like washers. Tools required are listed for both procedures.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...jdkskmmdmd1
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, including:
- Removing the rear gear group which involves taking out multiple gears, covers, seals, and bearings.
- Removing the flywheel which requires lifting equipment due to its weight and removing the ring gear.
- Installing the rear gear group and flywheel components in reverse order, noting specific requirements like matching dimensions and applying threadlocker to bolts.
Caterpillar Cat 345C L Hydraulic Excavator (Prefix ESD) Service Repair Manual...jdkskmmdmd1
The document provides instructions for disassembling a travel motor. It lists 31 steps to remove parts like the head, plates, seals, pins, and piston assemblies. Proper cleaning and identification of parts is emphasized to ensure correct reassembly. Tools required are listed in a table.
Caterpillar Cat 345C L Excavator (Prefix BWY) Service Repair Manual (BWY00001...jdkskmmdmd1
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, port plate, brake piston, disks, and rotating group. The assembly procedure reverses the disassembly with 13 steps like installing seals, spacers, washers, and plugs. Proper cleaning, identification of parts, and use of recommended tools are emphasized to avoid contamination and ensure correct assembly.
Massey Ferguson MF 840 COMBINES Parts Catalogue Manual.pdfjdkskmmdmd1
The document contains parts lists and diagrams for Massey Ferguson MF 840/845 combines. It lists over 50 individual parts for the engine and accessories, including the cylinder block, crankshaft, cylinder head, rocker arm assembly and other components. Each part is given an item number, part number, quantity, description and any relevant comments. Diagrams illustrate the layout and components of the engine systems.
Massey Ferguson MF 845 COMBINES Parts Catalogue Manual.pdfjdkskmmdmd1
The document contains parts lists and diagrams for Massey Ferguson MF 840/845 combines. It lists over 50 individual parts for the engine and related systems, including the cylinder block, crankshaft, cylinder head, rocker arm assembly, and other parts. Each part is given an item number, part number, quantity, description, and sometimes additional comments. Diagrams illustrate the layout and components of the engine and related systems.
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. Detailed steps are provided for each part along with accompanying illustrations. Similarly, the assembly section lists 28 steps to reinstall each part in reverse order, noting proper lubrication and torque specifications. Tools required are also outlined.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
This document provides instructions for removing and installing various components of a C27 Industrial Engine, including:
1. Removing the front gear group by removing bolts and gear assemblies.
2. Removing the front housing by removing covers, dampers, brackets, and bolts to detach the housing.
3. Removing the rear housing by removing elbow assemblies, bolts connecting the oil pan, and disconnecting hose assemblies.
1) The document provides instructions for removing and installing various components of a Caterpillar C9.3 industrial engine, including disconnecting snap-to-connect fittings, removing and installing a muffler, and removing and installing a fuel priming pump and fuel filter base.
2) The procedures include illustrations showing the components and numbered steps for disassembly and reassembly. Safety warnings are provided at the beginning regarding relieving pressures before disconnection.
3) Torque specifications and required tools are listed for relevant installation steps.
This document provides instructions for removing and installing various fuel system components on a Caterpillar C9 Industrial Engine, including:
- Removing and installing the fuel priming pump
- Removing and installing the fuel filter base
- Removing a unit injector from the engine cylinder head
The procedures describe draining fluids, using specialty tools to remove and install parts, cleaning components, lubricating seals, and torquing bolts to the specified values. Technicians are advised to take precautions to prevent spills and contamination when working on the fuel system.
This document provides instructions for disassembling and assembling components of a 938F wheel loader transmission. It describes removing the transmission from the vehicle and then disassembling it into individual parts like shafts, gears, seals, and clutches. The multi-step process includes using various tools to compress springs, remove snap rings, and disassemble interconnected sub-assemblies. Reassembly follows the reverse order and includes inspecting parts for wear and replacing as needed.
This document provides instructions for removing and installing an engine oil filter base and oil cooler from a Caterpillar C9 Industrial Engine. It describes:
- Draining the coolant from the cooling system before removal
- Using a strap wrench to remove the oil filter
- Disconnecting hoses and removing bolts to take off the oil filter base and oil cooler
- Cleaning and installing replacement parts in the reverse order
This document provides instructions for removing and installing various engine components on a Caterpillar C27 Industrial Engine, including:
1) Valves, springs, and related parts using specialized tools to compress springs.
2) Valve guides using a driver tool and ensuring proper height.
3) Valve seat inserts using an extractor tool and driver to install new inserts.
4) The engine oil filter base and related internal parts, noting any spring pressure hazards.
Caterpillar Cat 345D L Excavator (Prefix EEH) Service Repair Manual (EEH00001...jdkskmmdmd1
This document provides instructions for disassembling and assembling the final drive components of a 345D L Excavator. It describes removing 28 components in 28 steps, including the final drive cover, carrier assemblies, ring gear, and sprocket housing. Reassembly is described in 21 steps, beginning with installing bearing cups into the sprocket housing and ending by attaching the coupling to the motor housing. Tools required are listed.
This document provides instructions for removing and installing various engine components on a C27 Industrial Engine, including:
1) Inlet and exhaust valves, springs, and related parts.
2) Inlet and exhaust valve guides.
3) Inlet and exhaust valve seat inserts.
4) The engine oil filter base.
The procedures describe the required tools and provide illustrations showing the parts. Safety notices are included regarding spring-loaded components.
Caterpillar Cat 345C L Excavator (Prefix TBA) Service Repair Manual (TBA00001...jdkskmmdmd1
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, and brake piston. Identification marks should be made on parts for reassembly. To assemble, the document instructs reversing the 31 disassembly steps and notes that parts must be cleaned and reinstalled in their original locations and orientations.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual (KFH00001...jdkskmmdmd1
1. The document provides instructions for removing and installing the rear gear group and flywheel on a C13 engine.
2. It details the required tools and presents a step-by-step process with illustrations for disassembling, inspecting, and reassembling each component.
3. Special attention is given to bearing installation and torque specifications for fasteners.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1. Valves, valve guides, and valve seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2. The engine oil filter base, oil cooler, and oil pump. It emphasizes cleaning parts and contains fluids properly during removal and installation.
3. Safety precautions are provided, such as wearing protective equipment when working with spring-loaded parts and ensuring contaminants are avoided. Numerical sequences and specifications are given for installing certain parts correctly.
The document provides instructions for disassembling and assembling a travel motor. It is a 31 step process that includes removing components like the head, brake piston, disks, and seals. Tools required are listed. Cleanliness is emphasized to prevent contamination of hydraulic systems. Used parts should be replaced with new ones and marks made to ensure correct reinstallation of parts.
Massey Ferguson 1652 COMPACT TRACTORS Parts Catalogue Manual.pdfjdkskmmdmd1
This document is a table of contents for the engine, fuel, and exhaust systems of Massey Ferguson 1648, 1652, and 1655 compact tractors. It contains 91 pages listing component part numbers and references for the engine, fuel injection, cooling, exhaust, and related systems. The pages are organized by component and sub-components.
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, pins, plates, seals, pistons, disks, and bearings. The assembly procedure reverses the disassembly process in 30 steps and provides notes about cleaning parts, applying lubricant, and ensuring proper orientation of components like washers. Tools required are listed for both procedures.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...jdkskmmdmd1
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, including:
- Removing the rear gear group which involves taking out multiple gears, covers, seals, and bearings.
- Removing the flywheel which requires lifting equipment due to its weight and removing the ring gear.
- Installing the rear gear group and flywheel components in reverse order, noting specific requirements like matching dimensions and applying threadlocker to bolts.
Caterpillar Cat 345C L Hydraulic Excavator (Prefix ESD) Service Repair Manual...jdkskmmdmd1
The document provides instructions for disassembling a travel motor. It lists 31 steps to remove parts like the head, plates, seals, pins, and piston assemblies. Proper cleaning and identification of parts is emphasized to ensure correct reassembly. Tools required are listed in a table.
Caterpillar Cat 345C L Excavator (Prefix BWY) Service Repair Manual (BWY00001...jdkskmmdmd1
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, port plate, brake piston, disks, and rotating group. The assembly procedure reverses the disassembly with 13 steps like installing seals, spacers, washers, and plugs. Proper cleaning, identification of parts, and use of recommended tools are emphasized to avoid contamination and ensure correct assembly.
Massey Ferguson MF 840 COMBINES Parts Catalogue Manual.pdfjdkskmmdmd1
The document contains parts lists and diagrams for Massey Ferguson MF 840/845 combines. It lists over 50 individual parts for the engine and accessories, including the cylinder block, crankshaft, cylinder head, rocker arm assembly and other components. Each part is given an item number, part number, quantity, description and any relevant comments. Diagrams illustrate the layout and components of the engine systems.
Massey Ferguson MF 845 COMBINES Parts Catalogue Manual.pdfjdkskmmdmd1
The document contains parts lists and diagrams for Massey Ferguson MF 840/845 combines. It lists over 50 individual parts for the engine and related systems, including the cylinder block, crankshaft, cylinder head, rocker arm assembly, and other parts. Each part is given an item number, part number, quantity, description, and sometimes additional comments. Diagrams illustrate the layout and components of the engine and related systems.
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. Detailed steps are provided for each part along with accompanying illustrations. Similarly, the assembly section lists 28 steps to reinstall each part in reverse order, noting proper lubrication and torque specifications. Tools required are also outlined.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR JLD
Configuration: 325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
325C Excavator Machine Systems
Media Number -RENR5367-11 Publication Date -01/01/2012 Date Updated -17/02/2017
i05453056
Final Drive - Remove
SMCS - 4050-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8S-7611 Handle As 2
8S-7615 Pin As 2
283-1495 Stand Assembly 2
B 439-3939 Link Bracket As 2
C
154-6184 Forcing Bolt (M 20) 2
154-6185(1)
Forcing Bolt (M 24) 2
(1)
For Use on 329 and 330 sales models
Start By:
a. Separate the track assembly.
b. Remove the travel motor.
1/3
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. Illustration 1 g00489826
Typical Example
Note: Adjust the height of Tooling (A) so that there is sufficient clearance between the
sprocket and the track for the removal of the final drive.
1. Lift the side of the machine in order to install Tooling (A) under the frame, as shown.
Illustration 2 g00712767
2. Fasten Tooling (B) and a suitable lifting device to final drive (1), as shown. Put a slight
lifting tension on the final drive.
Illustration 3 g00712737
2/3
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Note: Mark the orientation of bolt holes (2) for the travel motor for installation purposes.
3. Remove bolts (3) and the washers from the final drive.
Illustration 4 g00712749
4. Use Tooling (C) in order to remove the final drive from the frame.
5. Carefully remove final drive (1). The weight of final drive (1) and the sprocket is
approximately 312 kg (688 lb).
6. Remove Tooling (C) from the frame.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jul 8 00:51:28 UTC+0800 2020
3/3
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR JLD
Configuration: 325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
325C Excavator Machine Systems
Media Number -RENR5367-11 Publication Date -01/01/2012 Date Updated -17/02/2017
i04758849
Final Drive - Disassemble
SMCS - 4050-015
Disassembly Procedure (227-6116)
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 138-7573 Link Bracket 2
C 1P-1863 Retaining Ring Pliers 1
D 194-3878 Spanner Socket 1
E 138-7574 Link Bracket 2
F
5F-7366 Forcing Screw 1
1P-5546 Crossblock 1
1U-9889 Crossblock 1
1P-0520 Driver Group 1
6V-7888 Puller Leg 2
1H-3112 Puller Assembly 1
1P-5551 Adjustable Screw Assembly 1
G
1U-7600 Slide Hammer Puller Gp 1
8T-0266 Bolt 1
1/13
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Start By:
A. Remove the final drive. Refer to Disassembly and Assembly, "Final Drive - Remove".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of
the component should be thoroughly cleaned. This will prevent dirt from entering the
internal mechanism.
Note: Some of the images that are in this procedure do not show the sprocket assembly that
is attached to the final drive housing. If necessary, the weights that are given include the
weight of the sprocket assembly.
1. Put an alignment mark across the sections of the final drive for assembly purposes. The
parts must be reinstalled in the part's original locations.
Illustration 1 g00708089
2. Fasten the final drive to Tooling (A), as shown. The weight of the final drive assembly is
approximately 312 kg (688 lb).
3. Remove bolts (1) and the washers that hold the cover in position.
Illustration 2 g00708090
2/13
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. 4. Remove the setscrews from the cover. Fasten Tooling (B) and a suitable lifting device to
cover (2), as shown. Remove the cover. The weight of the cover is approximately 32 kg (70
lb).
Illustration 3 g00879362
5. Remove bolts (3). Remove gear (5). Check plate (6). Replace plate (6) if wear is shown.
Remove plugs (4) from cover (2) .
Illustration 4 g00879365
6. Remove O-ring seal (7) from plugs (4) .
3/13
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Illustration 5 g00780428
7. Remove gear (8). Remove spacer (9) .
Illustration 6 g00780432
8. Remove retaining ring (10) with Tooling (C). Remove washer (11). Remove gear (12).
Remove bearing assembly (13). Remove second washer (11) .
9. Repeat Step 8 for the remaining two gear assemblies.
4/13
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Illustration 7 g00781401
10. Remove retaining ring (14) .
Illustration 8 g00781407
11. Remove carrier assembly (15) .
Illustration 9 g01389593
12. Use a suitable press in order to remove the shafts from carrier assembly (15) .
5/13
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. 16. Disassemble carrier assembly (19), as follows.
a. Drive spring pin (20) into planetary shaft (21) with a hammer and a punch.
Illustration 13 g00781476
b. Remove planetary shaft (21) .
c. Remove spring pin (20) from planetary shaft (21) with a hammer and a punch.
Illustration 14 g00781516
d. Remove thrust washers (22) and planetary gear (24) from the carrier assembly.
e. Remove bearing (23) from planetary gear (24) .
17. Repeat Steps 16.a through 16.e for the other two planetary.
7/13
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. Illustration 15 g00781529
18. Remove gear (25). Remove spacer (26) .
Illustration 16 g00781559
19. Remove carrier assembly (27) .
20. Use two people to remove carrier assembly (27). The weight of the carrier assembly is
approximately 38 kg (85 lb).
21. Disassemble carrier assembly (27), as follows.
8/13
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Illustration 17 g00781719
a. Drive spring pin (29) into planetary shaft (28) with a hammer and a punch.
Illustration 18 g00781601
b. Remove planetary shaft (28) .
c. Remove spring pin (29) from planetary shaft (28) with a hammer and a punch.
Illustration 19 g00781607
d. Remove thrust washers (30) and planetary gear (32) from the carrier assembly.
e. Remove two bearings (31) from the planetary gear.
22. Repeat Steps 21.a through 21.e for the other two planetary gears.
9/13
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Illustration 20 g00781730
23. Use two people to remove gear (33). The weight of gear is approximately 41 kg (90 lb).
Illustration 21 g00781807
24. Remove O-ring seal (34) .
Illustration 22 g01147650
25. Remove bolts (35A) and plates (35B) .
10/13
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engi...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Illustration 23 g01147651
26. Use Tooling (G) to remove dowel (37) from stopper plate (35) .
Illustration 24 g01147759
27. Secure Tooling (D) to stopper plate (35). Use Tooling (D) to remove stopper plate (35) .
11/13
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engi...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Illustration 25 g01147930
28. Use Tooling (E) and a suitable lifting device to remove housing (36). The weight of housing
(36) is approximately 100 kg (220 lb).
Illustration 26 g01147951
29. Remove Duo-Cone seal (39A) from housing (38) .
Illustration 27 g01147975
12/13
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engi...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Illustration 28 g01147934
30. Remove Duo-Cone seal (39B) from housing (36) .
31. Use Tooling (F) in order to remove bearings (40) and (41) from housing (36) .
32. If necessary, remove the final drive sprocket from the sprocket housing. Refer to
Disassembly and Assembly, "Final Drive Sprocket - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jul 8 00:52:24 UTC+0800 2020
13/13
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engi...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR JLD
Configuration: 325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
325C Excavator Machine Systems
Media Number -RENR5367-11 Publication Date -01/01/2012 Date Updated -17/02/2017
i04758848
Final Drive - Assemble
SMCS - 4050-016
Assembly Procedure (227-6116)
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 138-7573 Link Bracket 2
C 1P-1863 Retaining Ring Pliers 1
D
194-3878 Spanner Wrench As 1
194-3884 Spacer 1
E 138-7574 Link Bracket 2
H 6V-7030 Micrometer Depth Gauge Group 1
J FT-2770 Leak Down Test Tool 1
K 1U-6396 O-Ring Assembly Compound 1
L 5P-3931 Anti-Seize Compound 1
M 1U-8846 Gasket Sealant 1
N 8T-0531 Duo-Cone Seal Installer As 1
P 5P-3931 Anti-Seize Compound 1
Q 240-1886 Drill Fixture Gp 1
R 9S-3263 Thread Lock Compound 1
1/19
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Note: Cleanliness is an important factor. Before assembly, clean all parts thoroughly in cleaning
fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be
deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or
damaged, use new parts for replacement. All disassembly and all assembly procedures must be
performed on a clean work surface and in a clean hydraulic area. Keep cleaned parts covered and
protected at all times.
Note: O-ring seals, gaskets, and seals should always be replaced. A used O-ring seal may not have
the same sealing properties as a new O-ring. Use Tooling (K) during the assembly procedure.
Note: Apply a light film of hydraulic oil to all components before assembly.
Note: Some of the images that are in this procedure do not show the sprocket assembly that is
attached to the final drive housing. If necessary, the weights that are given include the weight of
the sprocket assembly.
Illustration 1 g01147975
1. Apply Tooling (P) to the outer diameter of the bearings.
2. Use a suitable press to Install bearings (40) and (41). Make sure that bearing (41) and
bearing (40) contact the counterbore in housing (36) .
3. Use Tooling (N) to install Duo-Cone seal (39B) .
2/19
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. Illustration 2 g01147981
4. Use Tooling (N) to install Duo-Cone seal (39A) onto housing (38).
Illustration 3 g01147930
5. Use Tooling (E) and a suitable lifting device to install housing (36) onto housing (38). The
weight of housing (36) is approximately 100 kg (220 lb).
6. Remove Tooling (E) from housing (36) .
3/19
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. Illustration 4 g01147724
7. Install stopper plate (35). Do not tighten stopper plate assembly (35) at this time.
Note: Stopper plate (35) will secure housing (36) to housing (38) .
8. Install Tooling (E) and a suitable lifting device to housing (36). The combined weight of
housing assembly (36) and (38) is approximately 120 kg (265 lb). Install housing assembly
(36) and (38) in a suitable press.
9. Remove stopper plate (35) .
Illustration 5 g01147727
10. Assemble Tooling (D), as shown.
Illustration 6 g01147731
11. Install Tooling (D) into housing (36), as shown.
12. Apply a force of 4000 kg (8818 lb) to the top of Tooling (D). Rotate housing (36) in order to
seat the bearings.
13. Reduce the force on the top of Tooling (D) to 1000 kg (2205 lb).
4/19
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Illustration 7 g01147737
14. Use Tooling (H) to take a measurement in three locations. Average the three measurements
and record the average measurement as Dimension (W) .
15. Remove Tooling (D) .
16. Separate Tooling (D) .
Illustration 8 g01147743
17. Use a micrometer in order to measure the thickness at three locations of the spacer from
Tooling (D). Record the average measurement as Dimension (X) .
5/19
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Illustration 9 g01147742
18. Use a micrometer in order to measure the thickness at three locations of stopper plate (35).
Record the average measurement as Dimension (Y) .
19. Subtract Dimension (X) from Dimension (Y) and record this figure as Dimension (Z) .
Illustration 10 g01147724
20. Install stopper plate (35) onto housing (38). Do not tighten stopper plate (35) at this time.
Stopper plate (35) will secure the final drive assembly while the final drive assembly is
repositioned onto Tooling (A) .
21. Use Tooling (E) and a suitable lifting device to reposition the final drive assembly onto
Tooling (A). The combined weight of housing assembly (36) and (38) is approximately 120
kg (265 lb).
22. Secure the final drive assembly to Tooling (A) .
6/19
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Illustration 11 g01148004
23. Secure the spanner socket from Tooling (D) to stopper plate (35) .
24. In order to determine the final bearing preload, add Dimension (W) to Dimension (Z) and
record this figure as Dimension (V) .
25. Use Tooling (H) to measure the distance in three locations.
26. Tighten stopper plate (35) until the average of the measurements is equal to Dimension (V) .
27. Remove Tooling (D) .
Illustration 12 g01372092
28. Install Tooling (Q) and a suitable vacuum onto stopper plate (35) .
7/19
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
25. Illustration 13 g01147789
29. Use a suitable drill and Tooling (Q) in order to drill a hole to the depth of 15 mm (0.6 inch)
in the stopper palte and in housing (38) .
Illustration 14 g01147796
30. Install dowel (37) .
Illustration 15 g01147650
8/19
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
26. 31. Apply Tooling (R) on bolts (35A). Install plate (35B) and bolts (35A) .
32. Repeat Steps 28 through 31 for the opposite side of stopper plate (35) .
Illustration 16 g00781807
33. Install O-ring seal (34) on housing (36) .
Illustration 17 g00781730
34. Install gear (33) on housing (36).
9/19
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
27. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
28. Illustration 18 g00781719
35. Assemble carrier assembly (27), as follows.
Illustration 19 g00781607
a. Use a deburring tool in order to remove the metal burr from the openings in the
carrier.
b. Install two bearings (31) in planetary gear (32) .
c. Install thrust washers (30) and planetary gear (32) in the carrier assembly.
d. Install planetary shaft (28) in the carrier assembly.
e. Align the split in spring pin (29) to the top or to the bottom. Make a stake mark on
each side of the spring pin hole in the carrier. Each stake mark should be
approximately 1.50 mm (0.059 inch) from the outside diameter of the spring pin hole.
10/19
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engi...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
29. Illustration 20 g00903073
f. Drive spring pin (29) into planetary shaft (28) with a hammer and a punch.
36. Repeat Steps 35.a through 35.e in order to install the other two planetary gears in the carrier.
Illustration 21 g00781559
37. Use two people to install carrier assembly (27) in gear (33). The weight of carrier assembly
(27) is approximately 38 kg (85 lb).
11/19
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engi...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...