This document provides instructions for disassembling the final drive on a 329D2L excavator. The steps include:
1. Removing the final drive assembly and placing it on a repair stand.
2. Removing the cover and gears/plates inside.
3. Dismantling the internal components of the final drive assembly, which includes removing planetary gears, bearings, seals, and housing pieces.
Caterpillar Cat 329D2L Excavator (Prefix WDT) Service Repair Manual (WDT00001...shudun96087
The document provides instructions for disassembling the final drive of a 329D2L excavator in 3 steps:
1. Remove the final drive assembly from the excavator and disassemble it into its main components including the cover, carrier assembly, ring gears, and main housing.
2. Further disassemble the carrier assembly and housing components to separate individual parts like planetary gears, shafts, seals, and bearings.
3. Use the required tools to lift, support, and remove each part, noting weight and orientation details to aid reassembly.
Caterpillar Cat 329D2L Excavator (Prefix WDT) Service Repair Manual (WDT00001...cnp692569
This document provides instructions for disassembling the final drive of a 329D2 L excavator. It begins by removing the final drive assembly and cleaning it. Then various parts like the cover, carrier assembly, ring gears, and housing are removed using specialized tools. Each step provides illustrations and notes cleaning requirements and part weights to aid with the disassembly process. The overall process is described in 33 steps and is intended to fully disassemble the final drive for repair or replacement of components.
Caterpillar Cat 329D2L Excavator (Prefix WDT) Service Repair Manual (WDT00001...kesi7153062
The document provides instructions for disassembling the final drive of a 329D2 L excavator. It describes:
1) Removing the final drive assembly and placing it on a repair stand.
2) Removing the cover by lifting it off with brackets and removing bolts and plugs.
3) Disassembling the internal components of the final drive which includes removing gears, shafts, washers, seals and housings using various tools.
Caterpillar cat 325 c excavator (prefix jld) service repair manual (jld00001 ...fhsejkdkmen
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and disassemble components of the final drive such as gears, carriers, shafts, and housings. Cleanliness is emphasized throughout. The assembly procedure is a reversal of the disassembly steps and involves applying sealants and lubricants to components before reinstalling them.
Caterpillar Cat 325C and 325C L Excavator (Prefix JLD) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for disassembling and removing the final drive from a 325C excavator. It lists the required tools and gives step-by-step details on removing the final drive housing, gears, carrier assemblies, and other components. Alignment marks should be made and weights of parts noted. Care must be taken due to the weights involved, with the final drive assembly weighing approximately 688 pounds and other parts ranging from 70 to 220 pounds.
Caterpillar cat 325 c l excavator (prefix jld) service repair manual (jld0000...fhsejkdkmen
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and disassemble components of the final drive such as gears, carriers, shafts, and housings. Cleanliness is emphasized throughout. The assembly procedure is a reversal of the disassembly steps and involves applying sealants and lubricants to components before reinstalling them.
Caterpillar Cat 325C and 325C L Excavator (Prefix JLD) Service Repair Manual ...zan2736ban
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and disassemble components of the final drive such as gears, carriers, shafts, and housings. Cleanliness is emphasized throughout. The assembly procedure is a reversal of the disassembly steps and involves applying sealants and lubricants to components before reinstalling them.
The document provides instructions for disassembling and removing the final drive from a 325C excavator. It lists the required tools and gives step-by-step details on removing the final drive housing, gears, carrier assemblies, and other components. Alignment marks should be made and weights of parts provided, as some components like the housing weigh over 100kg. Care must be taken when using tools to separate components and remove retaining rings, seals, and bearings from inside the final drive assembly.
Caterpillar Cat 329D2L Excavator (Prefix WDT) Service Repair Manual (WDT00001...shudun96087
The document provides instructions for disassembling the final drive of a 329D2L excavator in 3 steps:
1. Remove the final drive assembly from the excavator and disassemble it into its main components including the cover, carrier assembly, ring gears, and main housing.
2. Further disassemble the carrier assembly and housing components to separate individual parts like planetary gears, shafts, seals, and bearings.
3. Use the required tools to lift, support, and remove each part, noting weight and orientation details to aid reassembly.
Caterpillar Cat 329D2L Excavator (Prefix WDT) Service Repair Manual (WDT00001...cnp692569
This document provides instructions for disassembling the final drive of a 329D2 L excavator. It begins by removing the final drive assembly and cleaning it. Then various parts like the cover, carrier assembly, ring gears, and housing are removed using specialized tools. Each step provides illustrations and notes cleaning requirements and part weights to aid with the disassembly process. The overall process is described in 33 steps and is intended to fully disassemble the final drive for repair or replacement of components.
Caterpillar Cat 329D2L Excavator (Prefix WDT) Service Repair Manual (WDT00001...kesi7153062
The document provides instructions for disassembling the final drive of a 329D2 L excavator. It describes:
1) Removing the final drive assembly and placing it on a repair stand.
2) Removing the cover by lifting it off with brackets and removing bolts and plugs.
3) Disassembling the internal components of the final drive which includes removing gears, shafts, washers, seals and housings using various tools.
Caterpillar cat 325 c excavator (prefix jld) service repair manual (jld00001 ...fhsejkdkmen
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and disassemble components of the final drive such as gears, carriers, shafts, and housings. Cleanliness is emphasized throughout. The assembly procedure is a reversal of the disassembly steps and involves applying sealants and lubricants to components before reinstalling them.
Caterpillar Cat 325C and 325C L Excavator (Prefix JLD) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for disassembling and removing the final drive from a 325C excavator. It lists the required tools and gives step-by-step details on removing the final drive housing, gears, carrier assemblies, and other components. Alignment marks should be made and weights of parts noted. Care must be taken due to the weights involved, with the final drive assembly weighing approximately 688 pounds and other parts ranging from 70 to 220 pounds.
Caterpillar cat 325 c l excavator (prefix jld) service repair manual (jld0000...fhsejkdkmen
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and disassemble components of the final drive such as gears, carriers, shafts, and housings. Cleanliness is emphasized throughout. The assembly procedure is a reversal of the disassembly steps and involves applying sealants and lubricants to components before reinstalling them.
Caterpillar Cat 325C and 325C L Excavator (Prefix JLD) Service Repair Manual ...zan2736ban
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and disassemble components of the final drive such as gears, carriers, shafts, and housings. Cleanliness is emphasized throughout. The assembly procedure is a reversal of the disassembly steps and involves applying sealants and lubricants to components before reinstalling them.
The document provides instructions for disassembling and removing the final drive from a 325C excavator. It lists the required tools and gives step-by-step details on removing the final drive housing, gears, carrier assemblies, and other components. Alignment marks should be made and weights of parts provided, as some components like the housing weigh over 100kg. Care must be taken when using tools to separate components and remove retaining rings, seals, and bearings from inside the final drive assembly.
Caterpillar Cat 325C L Excavator (Prefix JLD) Service Repair Manual (JLD00001...f8uesjdkdmdm
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and disassemble components of the final drive such as gears, carriers, shafts, and housings. Cleanliness is emphasized throughout. The assembly procedure is largely the reverse of the disassembly steps and involves applying sealants and lubricants before reinstalling components.
Caterpillar cat 325 c l excavator (prefix jld) service repair manual (jld0000...ikdkkdmdmdm
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and disassemble components of the final drive such as gears, carriers, shafts, and housings. Cleanliness is emphasized throughout. The assembly procedure is a reversal of the disassembly steps and involves applying sealants and lubricants to components before reinstalling them.
Caterpillar Cat 325C L Excavator (Prefix JLD) Service Repair Manual (JLD00001...f7fujksekmdm8u
The document provides instructions for disassembling and removing the final drive from a 325C excavator. It lists the required tools and gives step-by-step details on removing the final drive housing, gears, shafts, and other components. Alignment marks should be made and weights of parts provided, as the components must be reinstalled in their original locations. Careful cleaning is important to prevent dirt from entering the mechanism during disassembly.
The document provides instructions for disassembling and removing the final drive from a 325C excavator. It lists the required tools and gives step-by-step details on removing the final drive housing, gears, carrier assemblies, and other components. Alignment marks should be made and weights of parts provided, as some components like the housing weigh over 100kg. Care must be taken during disassembly to prevent dirt from entering internal mechanisms.
Caterpillar cat 325 c excavator (prefix jld) service repair manual (jld00001 ...ikdkkdmdmdm
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and disassemble components of the final drive such as gears, carriers, shafts, and housings. Cleanliness is emphasized throughout. The assembly procedure is a reversal of the disassembly steps and involves applying sealants and lubricants to components before reinstalling them.
Caterpillar Cat 325C L Excavator (Prefix JLD) Service Repair Manual (JLD00001...f8sejdkdmdijd
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and disassemble components of the final drive such as gears, carriers, shafts, and housings. Cleanliness is emphasized throughout. The assembly procedure is largely the reverse of the disassembly steps and involves applying sealants and lubricants before reinstalling components.
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and install components like gears, carriers, seals, and housings. Cleanliness is emphasized and O-rings, gaskets, and seals should always be replaced. The assembly procedure is the reverse of the disassembly with tools and compounds used to install specific parts correctly.
Caterpillar Cat 325C and 325C L Excavator (Prefix JLD) Service Repair Manual ...fujkskemdmdm4r
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and install components like gears, carriers, seals, and housings. Cleanliness is emphasized and O-rings, gaskets, and seals should always be replaced. The assembly procedure is the reverse of the disassembly with notes to apply lubricants and check parts for wear.
The document provides instructions for disassembling and removing the final drive from a 325C excavator. It lists the required tools and gives step-by-step details on removing the final drive housing, gears, shafts, and other components. Alignment marks should be made and weights of parts provided, as the components must be reinstalled in their original locations. Careful cleaning is important to prevent dirt from entering the mechanism during disassembly.
Caterpillar Cat 325C L Excavator (Prefix JLD) Service Repair Manual (JLD00001...ufs89eodkdmdm
The document provides instructions for disassembling and removing the final drive from a 325C excavator. It lists the required tools and gives step-by-step details on removing the final drive housing, gears, carrier assemblies, and other components. Alignment marks should be made and weights of parts noted. Care must be taken due to the weights involved, with the final drive assembly weighing approximately 688 pounds and other parts ranging from 70 to 220 pounds.
Caterpillar Cat 325C L Excavator (Prefix JLD) Service Repair Manual (JLD00001...jdkskmmdmd1
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and install components like gears, carriers, seals, and housings. Cleanliness is emphasized throughout and O-rings, gaskets, and seals should always be replaced. The assembly procedure is the reverse of the disassembly with notes to apply lubricants and check parts for wear.
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and install components like gears, carriers, seals, and housings. Cleanliness is emphasized and O-rings, gaskets, and seals should always be replaced. The assembly procedure is the reverse of the disassembly with notes to apply lubricants and check parts for wear.
Caterpillar Cat 325C and 325C L Excavator (Prefix JLD) Service Repair Manual ...fskekkdmdmdm3e
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and install components like gears, carriers, seals, and housings. Cleanliness is emphasized and O-rings, gaskets, and seals should always be replaced. The assembly procedure is the reverse of the disassembly with notes to apply lubricants and check parts for wear.
Caterpillar Cat 325C L Excavator (Prefix JLD) Service Repair Manual (JLD00001...jdkskmdmdm
The document provides instructions for disassembling and removing the final drive from a 325C excavator. It lists the required tools and gives step-by-step details on removing the final drive housing, gears, carrier assemblies, and other components. Alignment marks should be made and weights of parts noted. Care must be taken due to the weights involved, with the final drive assembly weighing approximately 688 pounds and other parts ranging from 70 to 220 pounds.
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and install components like gears, carriers, seals, and housings. Cleanliness is emphasized and O-rings, gaskets, and seals should always be replaced. The assembly procedure is the reverse of the disassembly with notes to apply lubricants and check parts for wear.
Caterpillar Cat 325C L Excavator (Prefix JLD) Service Repair Manual (JLD00001...pwg56547003
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and disassemble components of the final drive such as gears, carriers, shafts, and housings. Cleanliness is emphasized throughout. The assembly procedure is a reversal of the disassembly steps and involves applying sealants and lubricants to components before reinstalling them.
This document provides instructions for removing and installing cylinder heads on a Caterpillar 3176C engine. The removal procedure involves removing various components like sensors, tubes, and manifolds to access the cylinder head. Thirteen steps are outlined to remove the cylinder head, which weighs 135 kg. The installation procedure involves cleaning surfaces, inspecting for damage, selecting the correct gasket, and torquing 26 bolts to secure the cylinder head. Proper cleaning and installation of gaskets and seals is emphasized to prevent leaks.
Caterpillar Cat 345B Series II Excavator (Prefix ALB) Service Repair Manual (...f7djidksmd3e
This document provides assembly instructions for a travel motor on an excavator model 345B Series II. It outlines 31 steps to assemble components like the head, housing, plates, seals, and more. Technicians are advised to clean all parts thoroughly, replace all O-rings and seals, and ensure components are reinstalled in their original locations and orientations. Proper assembly helps prevent contamination and failures.
Caterpillar Cat 345C HCR Material Handler EXCAVATOR (Prefix MTE) Service Repa...f7djidksmd3e
This document provides instructions for removing and installing the rear gear group and flywheel on a C13 engine. It outlines:
1) The required tools and removal procedure for the rear gear group which involves removing bolts, seals, gears, bushings and bearings.
2) The installation procedure for the rear gear group which specifies cleaning, applying lubricant and torque specifications for installing the components in reverse order of removal.
3) The removal procedure for the flywheel which requires attaching lifting equipment and removing bolts and ring gear.
4) The installation procedure for the flywheel which involves heating components, applying threadlocker and torque specifications.
Caterpillar Cat 345B L Series II Excavator (Prefix ALB) Service Repair Manual...f7djidksmd3e
This document provides assembly instructions for a travel motor on an excavator model 345B Series II. It outlines 31 steps to assemble components like the head, housing, plates, seals, and pins. Special tools are required for tasks like installing seals. Technicians are advised to clean all parts, replace all seals and O-rings, and correct any conditions that caused prior failures.
Caterpillar Cat 345B L Excavator (Prefix 9GS) Service Repair Manual (9GS00001...f7djidksmd3e
This document provides instructions for removing and installing cylinder heads on 345B and 345B L excavator models. The removal procedure involves removing various components to access the cylinder head such as the valve cover, rocker arms, and sensors. The cylinder head is then removed using lifting equipment due to its weight of 135 kg. The installation procedure specifies cleaning surfaces, installing new gaskets and seals, and tightening head bolts to the proper specification. Special tools and repair kits are listed for tasks such as tapping threads and installing Helicoil inserts if head bolt threads are damaged.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3176C engine. It describes removing components like sensors, tubes, and manifolds. It instructs to clean mating surfaces, select the correct gasket, and install the head using a lifting device. Detailed steps are given for tightening the head bolts in a specific sequence and torque pattern to properly secure the cylinder head.
More Related Content
Similar to Caterpillar Cat 329D2L Excavator (Prefix WDT) Service Repair Manual (WDT00001 and up).pdf
Caterpillar Cat 325C L Excavator (Prefix JLD) Service Repair Manual (JLD00001...f8uesjdkdmdm
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and disassemble components of the final drive such as gears, carriers, shafts, and housings. Cleanliness is emphasized throughout. The assembly procedure is largely the reverse of the disassembly steps and involves applying sealants and lubricants before reinstalling components.
Caterpillar cat 325 c l excavator (prefix jld) service repair manual (jld0000...ikdkkdmdmdm
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and disassemble components of the final drive such as gears, carriers, shafts, and housings. Cleanliness is emphasized throughout. The assembly procedure is a reversal of the disassembly steps and involves applying sealants and lubricants to components before reinstalling them.
Caterpillar Cat 325C L Excavator (Prefix JLD) Service Repair Manual (JLD00001...f7fujksekmdm8u
The document provides instructions for disassembling and removing the final drive from a 325C excavator. It lists the required tools and gives step-by-step details on removing the final drive housing, gears, shafts, and other components. Alignment marks should be made and weights of parts provided, as the components must be reinstalled in their original locations. Careful cleaning is important to prevent dirt from entering the mechanism during disassembly.
The document provides instructions for disassembling and removing the final drive from a 325C excavator. It lists the required tools and gives step-by-step details on removing the final drive housing, gears, carrier assemblies, and other components. Alignment marks should be made and weights of parts provided, as some components like the housing weigh over 100kg. Care must be taken during disassembly to prevent dirt from entering internal mechanisms.
Caterpillar cat 325 c excavator (prefix jld) service repair manual (jld00001 ...ikdkkdmdmdm
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and disassemble components of the final drive such as gears, carriers, shafts, and housings. Cleanliness is emphasized throughout. The assembly procedure is a reversal of the disassembly steps and involves applying sealants and lubricants to components before reinstalling them.
Caterpillar Cat 325C L Excavator (Prefix JLD) Service Repair Manual (JLD00001...f8sejdkdmdijd
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and disassemble components of the final drive such as gears, carriers, shafts, and housings. Cleanliness is emphasized throughout. The assembly procedure is largely the reverse of the disassembly steps and involves applying sealants and lubricants before reinstalling components.
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and install components like gears, carriers, seals, and housings. Cleanliness is emphasized and O-rings, gaskets, and seals should always be replaced. The assembly procedure is the reverse of the disassembly with tools and compounds used to install specific parts correctly.
Caterpillar Cat 325C and 325C L Excavator (Prefix JLD) Service Repair Manual ...fujkskemdmdm4r
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and install components like gears, carriers, seals, and housings. Cleanliness is emphasized and O-rings, gaskets, and seals should always be replaced. The assembly procedure is the reverse of the disassembly with notes to apply lubricants and check parts for wear.
The document provides instructions for disassembling and removing the final drive from a 325C excavator. It lists the required tools and gives step-by-step details on removing the final drive housing, gears, shafts, and other components. Alignment marks should be made and weights of parts provided, as the components must be reinstalled in their original locations. Careful cleaning is important to prevent dirt from entering the mechanism during disassembly.
Caterpillar Cat 325C L Excavator (Prefix JLD) Service Repair Manual (JLD00001...ufs89eodkdmdm
The document provides instructions for disassembling and removing the final drive from a 325C excavator. It lists the required tools and gives step-by-step details on removing the final drive housing, gears, carrier assemblies, and other components. Alignment marks should be made and weights of parts noted. Care must be taken due to the weights involved, with the final drive assembly weighing approximately 688 pounds and other parts ranging from 70 to 220 pounds.
Caterpillar Cat 325C L Excavator (Prefix JLD) Service Repair Manual (JLD00001...jdkskmmdmd1
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and install components like gears, carriers, seals, and housings. Cleanliness is emphasized throughout and O-rings, gaskets, and seals should always be replaced. The assembly procedure is the reverse of the disassembly with notes to apply lubricants and check parts for wear.
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and install components like gears, carriers, seals, and housings. Cleanliness is emphasized and O-rings, gaskets, and seals should always be replaced. The assembly procedure is the reverse of the disassembly with notes to apply lubricants and check parts for wear.
Caterpillar Cat 325C and 325C L Excavator (Prefix JLD) Service Repair Manual ...fskekkdmdmdm3e
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and install components like gears, carriers, seals, and housings. Cleanliness is emphasized and O-rings, gaskets, and seals should always be replaced. The assembly procedure is the reverse of the disassembly with notes to apply lubricants and check parts for wear.
Caterpillar Cat 325C L Excavator (Prefix JLD) Service Repair Manual (JLD00001...jdkskmdmdm
The document provides instructions for disassembling and removing the final drive from a 325C excavator. It lists the required tools and gives step-by-step details on removing the final drive housing, gears, carrier assemblies, and other components. Alignment marks should be made and weights of parts noted. Care must be taken due to the weights involved, with the final drive assembly weighing approximately 688 pounds and other parts ranging from 70 to 220 pounds.
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and install components like gears, carriers, seals, and housings. Cleanliness is emphasized and O-rings, gaskets, and seals should always be replaced. The assembly procedure is the reverse of the disassembly with notes to apply lubricants and check parts for wear.
Caterpillar Cat 325C L Excavator (Prefix JLD) Service Repair Manual (JLD00001...pwg56547003
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and disassemble components of the final drive such as gears, carriers, shafts, and housings. Cleanliness is emphasized throughout. The assembly procedure is a reversal of the disassembly steps and involves applying sealants and lubricants to components before reinstalling them.
Similar to Caterpillar Cat 329D2L Excavator (Prefix WDT) Service Repair Manual (WDT00001 and up).pdf (16)
This document provides instructions for removing and installing cylinder heads on a Caterpillar 3176C engine. The removal procedure involves removing various components like sensors, tubes, and manifolds to access the cylinder head. Thirteen steps are outlined to remove the cylinder head, which weighs 135 kg. The installation procedure involves cleaning surfaces, inspecting for damage, selecting the correct gasket, and torquing 26 bolts to secure the cylinder head. Proper cleaning and installation of gaskets and seals is emphasized to prevent leaks.
Caterpillar Cat 345B Series II Excavator (Prefix ALB) Service Repair Manual (...f7djidksmd3e
This document provides assembly instructions for a travel motor on an excavator model 345B Series II. It outlines 31 steps to assemble components like the head, housing, plates, seals, and more. Technicians are advised to clean all parts thoroughly, replace all O-rings and seals, and ensure components are reinstalled in their original locations and orientations. Proper assembly helps prevent contamination and failures.
Caterpillar Cat 345C HCR Material Handler EXCAVATOR (Prefix MTE) Service Repa...f7djidksmd3e
This document provides instructions for removing and installing the rear gear group and flywheel on a C13 engine. It outlines:
1) The required tools and removal procedure for the rear gear group which involves removing bolts, seals, gears, bushings and bearings.
2) The installation procedure for the rear gear group which specifies cleaning, applying lubricant and torque specifications for installing the components in reverse order of removal.
3) The removal procedure for the flywheel which requires attaching lifting equipment and removing bolts and ring gear.
4) The installation procedure for the flywheel which involves heating components, applying threadlocker and torque specifications.
Caterpillar Cat 345B L Series II Excavator (Prefix ALB) Service Repair Manual...f7djidksmd3e
This document provides assembly instructions for a travel motor on an excavator model 345B Series II. It outlines 31 steps to assemble components like the head, housing, plates, seals, and pins. Special tools are required for tasks like installing seals. Technicians are advised to clean all parts, replace all seals and O-rings, and correct any conditions that caused prior failures.
Caterpillar Cat 345B L Excavator (Prefix 9GS) Service Repair Manual (9GS00001...f7djidksmd3e
This document provides instructions for removing and installing cylinder heads on 345B and 345B L excavator models. The removal procedure involves removing various components to access the cylinder head such as the valve cover, rocker arms, and sensors. The cylinder head is then removed using lifting equipment due to its weight of 135 kg. The installation procedure specifies cleaning surfaces, installing new gaskets and seals, and tightening head bolts to the proper specification. Special tools and repair kits are listed for tasks such as tapping threads and installing Helicoil inserts if head bolt threads are damaged.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3176C engine. It describes removing components like sensors, tubes, and manifolds. It instructs to clean mating surfaces, select the correct gasket, and install the head using a lifting device. Detailed steps are given for tightening the head bolts in a specific sequence and torque pattern to properly secure the cylinder head.
This document provides instructions for removing and installing cylinder heads on 345B and 345B L excavator models. The removal procedure involves removing various components to access the cylinder head such as the valve cover, rocker arms, and pushrods. Specific bolts and sensors must then be removed from the cylinder head. The installation procedure specifies cleaning surfaces, installing new gaskets and seals, and tightening head bolts to the proper torque. Special tools and repair kits are listed for tasks such as removing fuel filters and repairing damaged cylinder block threads.
Caterpillar Cat 345B II MH EXCAVATOR (Prefix APB) Service Repair Manual (APB0...f7djidksmd3e
The document provides instructions to disassemble a swing drive for a 345B II MH excavator. Key steps include:
1. Draining the oil and removing covers and gears to access the internal components.
2. Using punches and hammers to remove pins holding planetary gears to disassemble the carrier assembly.
3. Removing the ring gear, carrier assembly, and other internal parts which require multiple people due to weights over 35 kg.
The purpose is to fully disassemble the swing drive to facilitate repair or replacement of internal components.
Caterpillar Cat 345B II EXCAVATOR (Prefix FEE) Service Repair Manual (FEE0000...f7djidksmd3e
This document provides instructions for assembling the swing drive of a 345B II excavator. Key steps include:
1. Cleaning and inspecting all parts before assembly.
2. Applying anti-seize compound and grease to bearings and installing them into the swing drive housing along with the pinion shaft and bearing cage.
3. Heating and pressing bearings onto the pinion shaft and installing the assembly into the swing drive housing using a press.
4. Temporarily installing bolts to hold the bearing cage aligned with the housing. The instructions provide details on lubricants to use and proper positioning of parts.
The document provides instructions for disassembling a piston motor (hydraulic fan) with the following key steps:
1. Remove the head and internal components like seals, plates, and bearings.
2. Extract the pistons, retainer, and bearings from the housing.
3. Use specialty tools to remove the retaining ring and springs, allowing removal of the swashplate and shaft.
Proper safety precautions and cleaning of parts is emphasized before disassembly.
Caterpillar Cat 336E L HVG Excavator (Prefix RBS) Service Repair Manual (RBS0...f7djidksmd3e
The document provides instructions to remove the rear power take-off (RPTO) from a Caterpillar C9.3 engine. The steps are:
1. Remove the flywheel housing.
2. Remove the rear cover and gasket.
3. Remove the rear power take-off (RPTO) and O-ring seal.
This document provides instructions for disassembling and assembling the travel motor on Caterpillar 345B and 345B L Excavator models. It lists required tools and parts and provides 32 numbered steps to fully disassemble the travel motor by removing components like brackets, covers, pistons, plates, seals, and housing pieces. Illustrations accompany each step to show how to position the motor and parts for disassembly and reassembly. Safety notices are also included to handle parts and fluids properly.
Caterpillar Cat 340D2 L Excavator (Prefix HHK) Service Repair Manual (HHK0000...f7djidksmd3e
The document provides instructions for disassembling the final drive of an excavator model 340D2 L. It describes 25 steps to remove components such as gears, shafts, seals, bearings and housings. Various tools are required including link brackets and forcing bolts to compress springs. Personal protective equipment is recommended as parts can be propelled by released spring forces. The total weight of the final drive assembly is approximately 550 kg.
Caterpillar Cat 340F L LRE Excavator (Prefix YBF) Service Repair Manual (YBF0...f7djidksmd3e
This document provides the disassembly and assembly procedures for the travel motor on a 340F L LRE excavator. It includes 27 steps to disassemble the travel motor by removing components like the head, springs, plates, seals and bearings. The 27 steps to assemble list installing these same components in reverse order and include notes about lubrication, alignment and torque specifications. Required tools are listed for both procedures.
The document provides instructions for removing and installing an engine oil filter base on a 336D LN excavator. It describes:
1) Removing various connectors, seals, valves, and plugs from the engine oil filter base during disassembly.
2) Assembling the engine oil filter base by installing the parts in reverse order of removal.
3) Installing the engine oil filter base on the engine, including attaching hoses and bolts.
The document provides instructions for installing a rear power take-off (RPTO) on a C9.3 engine. The procedure involves installing various components like a bearing, thrust washer, dowels, adapter assembly, idler gear and shaft. Tools like guide studs and driver groups are required. Torque specifications and the correct sequence are important to properly install the RPTO.
This document provides instructions for disassembling and assembling the travel motor of a 336E excavator. The disassembly process involves removing 27 different components of the travel motor including the head, springs, brake piston, plates, and seals. The assembly process reverses the disassembly steps and provides details on lubricating parts and ensuring proper alignment of components like the cam plate and brake piston. Special tools are required for tasks like removing the rotating assembly and installing seals and bearings.
The document provides instructions for installing a cylinder head on a Caterpillar 330 excavator engine. It describes:
1. Cleaning the cylinder head and ensuring it is free of contaminants before installation.
2. Attaching the cylinder head to the cylinder block using bolts in the specified tightening sequence and torque.
3. Reinstalling related components like the exhaust manifold, fuel injection lines, and valve train once the cylinder head is secured.
The summary highlights the key steps of cleaning the cylinder head, attaching it to the engine block, and reinstalling additional parts. It is provided in 3 sentences as requested.
The document provides instructions for installing and removing a turbocharger on a Caterpillar 330 excavator engine:
1) To remove the turbocharger, loosen clamps and bolts holding the oil supply/drain tubes and housing. Remove the turbocharger and check seals.
2) To install the turbocharger, position it on the exhaust manifold with new gaskets. Attach the oil tubes and housing with bolts and clamps.
3) The instructions also cover removing and installing the exhaust manifold, which involves removing nuts and studs, checking gaskets, and attaching the manifold.
Caterpillar Cat 330D N Hydraulic Excavator (Prefix RAS) Service Repair Manual...f7djidksmd3e
The document provides instructions for removing and disassembling the swivel component of a 330D L hydraulic excavator. It lists required tools and outlines a 15 step procedure for removing the swivel that includes disconnecting hoses, removing bolts and other fasteners, and using lifting devices. A 7 step disassembly procedure is also provided which involves cleaning, positioning, and separating the swivel's outer housing and rotor components using bolts, washers, and specialized tooling. Personal protective equipment is recommended when handling fluids.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 329D2 L EXCAVATOR WDT
Configuration: 329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
326D2, 329D2 and 330D2 Excavators Machine Systems
Media Number -UENR6134-08 Publication Date -01/09/2018 Date Updated -12/09/2018
i05453056
Final Drive - Remove
SMCS - 4050-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8S-7611 Handle As 2
8S-7615 Pin As 2
283-1495 Stand Assembly 2
B 439-3939 Link Bracket As 2
C
154-6184 Forcing Bolt (M 20) 2
154-6185(1)
Forcing Bolt (M 24) 2
(1)
For Use on 329 and 330 sales models
Start By:
a. Separate the track assembly.
b. Remove the travel motor.
1/3
329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine(SEB...
2020/4/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00489826
Typical Example
Note: Adjust the height of Tooling (A) so that there is sufficient clearance between the
sprocket and the track for the removal of the final drive.
1. Lift the side of the machine in order to install Tooling (A) under the frame, as shown.
Illustration 2 g00712767
2. Fasten Tooling (B) and a suitable lifting device to final drive (1), as shown. Put a slight
lifting tension on the final drive.
Illustration 3 g00712737
2/3
329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine(SEB...
2020/4/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Note: Mark the orientation of bolt holes (2) for the travel motor for installation purposes.
3. Remove bolts (3) and the washers from the final drive.
Illustration 4 g00712749
4. Use Tooling (C) in order to remove the final drive from the frame.
5. Carefully remove final drive (1). The weight of final drive (1) and the sprocket is
approximately 312 kg (688 lb).
6. Remove Tooling (C) from the frame.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Apr 30 08:38:20 UTC+0800 2020
3/3
329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine(SEB...
2020/4/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 329D2 L EXCAVATOR WDT
Configuration: 329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
326D2, 329D2 and 330D2 Excavators Machine Systems
Media Number -UENR6134-08 Publication Date -01/09/2018 Date Updated -12/09/2018
i02606369
Final Drive - Disassemble
SMCS - 4050-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 138-7573 Link Bracket 2
C 154-6181 Forcing Screw 1
D 138-7574 Link Bracket 2
E
5F-7366 Forcing Screw 1
1P-5546 Crossblock 1
1U-9889 Crossblock 1
1P-0520 Driver Group 1
6V-7888 Puller Leg 2
1H-3112 Puller Assembly 1
1P-5551 Adjustable Screw Assembly 1
F 1U-8846 Gasket Sealant 1
Start By:
a. Remove the final drive. Refer to Disassembly and Assembly, "Final Drive - Remove".
1/11
329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine(SEB...
2020/4/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of
the component should be thoroughly cleaned. This will prevent dirt from entering the
internal mechanism.
1. Put an alignment mark across the sections of the final drive for assembly purposes. The
parts must be reinstalled in the part's original locations.
Illustration 1 g00708089
2. Fasten the final drive to Tooling (A), as shown. The combined weight of the final drive and
final drive sprocket is approximately 312 kg (688 lb).
3. Remove bolts (1) and the washers that hold the cover in position.
Illustration 2 g00708090
4. Remove the setscrews from the cover. Fasten Tooling (B) and a suitable lifting device to
cover (2), as shown. The weight of cover (2) is approximately 32 kg (70 lb). Remove cover
(2).
2/11
329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine(SEB...
2020/4/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 3 g00708091
5. Remove thrust plate (3) from cover (2).
6. Remove plugs (4) from cover (2).
Illustration 4 g00708235
7. Remove O-ring seals (5) from both plugs (4) that were in the cover.
Illustration 5 g00708092
8. Remove spacer (6) from carrier assembly (7).
9. Remove sun gear (8) from carrier assembly (7).
3/11
329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine(SEB...
2020/4/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. 10. Remove carrier assembly (7) by lifting the carrier assembly straight up. The weight of
carrier assembly (7) is approximately 14 kg (30 lb).
Illustration 6 g01304883
11. Disassemble carrier assembly (7), as follows.
a. Drive spring pin (10) into planetary shaft (9) with a hammer and a punch.
Illustration 7 g00708144
b. Remove planetary shaft (9) with spring pin (10) from the carrier assembly.
c. Remove spring pin (10) from planetary shaft (9) with a hammer and a punch.
4/11
329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine(SEB...
2020/4/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 8 g00708218
d. Remove thrust washers (11) and planetary gear (13) from the carrier assembly.
e. Remove bearing (12) from planetary gear (13).
12. Repeat Steps 11.a through 11.e in order to remove the remaining planetary gears from the
carrier assembly.
Illustration 9 g00708162
13. Remove sun gear (14) from carrier assembly (15).
Illustration 10 g00708325
14. Remove spacer (16).
5/11
329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine(SEB...
2020/4/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 11 g00708184
Note: It will be necessary to pry ring gears (17) away from main housing (18) in order to
install the lifting slings.
15. Fasten a suitable lifting device to ring gears (17), as shown. Remove the ring gears from
main housing (18). The weight of ring gears (17) is approximately 45 kg (100 lb).
Illustration 12 g00708360
16. Use a screwdriver or a chisel in order to separate the two ring gears (17).
Note: The two ring gears are held together with Tooling (F). It may be necessary to heat the
ring gears in order to soften the sealant. Do not heat over 135 °C (275 °F) for more than
thirty minutes.
6/11
329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine(SEB...
2020/4/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 13 g00708172
17. Position a 12.7 mm (0.50 inch) shackle under carrier assembly (15).
18. Fasten a suitable lifting device to the shackle.
19. Slowly lift carrier assembly (15) from the final drive. The weight of carrier assembly (15) is
approximately 39 kg (85 lb).
20. Disassemble carrier assembly (15), as follows.
Illustration 14 g00708175
a. Drive spring pin (20) into planetary shaft (19) with a hammer and a punch.
7/11
329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine(SEB...
2020/4/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 15 g00708370
Illustration 16 g00708220
b. Remove planetary shaft (19) with spring pin (20) from the carrier assembly.
c. Remove spring pin (20) from planetary shaft (19) with a hammer and a punch.
d. Remove thrust washers (21) and planetary gear (23) from the carrier assembly.
e. Remove bearings (22) from planetary gear (23).
21. Repeat Steps 20.a through 20.e in order to remove the remaining planetary gears from the
carrier.
Illustration 17 g00708186
22. Remove O-ring seal (24) from main housing (18).
8/11
329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine(SEB...
2020/4/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 18 g00708187
23. Remove bolts (25) from gear (26).
Illustration 19 g00708202
24. Use Tooling (C) in order to remove gear (26) from main housing (18).
Note: The motor housing will separate from the main housing (18) once gear (26) is
removed. Make sure that the motor housing is supported.
Illustration 20 g00708211
25. Remove shims (27) from the main housing.
9/11
329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine(SEB...
2020/4/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 21 g00708212
26. Fasten Tooling (D) and a suitable lifting device to main housing (18), as shown.
27. Use a hammer and a punch in order to separate main housing (18) and the final drive
sprocket from the motor housing (28). The combined weight of main housing (18) and the
final drive sprocket is approximately 82 kg (180 lb).
Illustration 22 g00708214
28. Remove Duo-Cone seal (29) from motor housing (28).
29. Remove alignment pins (30).
10/11
329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine(S...
2020/4/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 23 g00708215
Illustration 24 g00708216
30. Remove Duo-Cone seal (31) from main housing (18).
31. Use Tooling (E) in order to remove bearings (32) and (33) from the main housing.
32. If necessary, remove the final drive sprocket from the main housing.
33. Refer to Disassembly and Assembly, "Final Drive Sprocket - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Apr 30 08:39:16 UTC+0800 2020
11/11
329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine(S...
2020/4/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 329D2 L EXCAVATOR WDT
Configuration: 329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
326D2, 329D2 and 330D2 Excavators Machine Systems
Media Number -UENR6134-08 Publication Date -01/09/2018 Date Updated -12/09/2018
i03508206
Final Drive - Disassemble
SMCS - 4050-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 138-7573 Link Bracket 2
C 1P-1863 Retaining Ring Pliers 1
D 138-7575 Link Bracket 3
E 4C-8359 Eyebolt 2
F 138-7574 Link Bracket 2
G 138-7576 Link Bracket 2
Start By:
a. Start by removing the final drive. Refer to Disassembly and Assembly, "Final Drive -
Remove".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of
the component should be thoroughly cleaned. This will prevent dirt from entering the
internal mechanism.
1. Put an alignment mark across the sections of the final drive for assembly purposes. The
parts must be reinstalled to the original locations.
1/12
329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine(SEB...
2020/4/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 1 g00892878
2. Use Tooling (G) and a suitable lifting device to position the final drive assembly onto
Tooling (A). The weight of the final drive assembly is approximately 550 kg (1200 lb).
3. Remove bolts (1).
Illustration 2 g00892883
4. Use Tooling (B) and a suitable lifting device to remove cover (2). The weight of cover (2) is
approximately 32 kg (70 lb).
Illustration 3 g00892888
2/12
329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine(SEB...
2020/4/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. 5. Remove bolts (3) and gear (4). Check plate (6). Replace plate (6) if plate (6) is worn.
Remove plugs (5) from cover (2).
Illustration 4 g00892906
6. Remove O-ring seals (7) from plugs (5).
Illustration 5 g00892930
7. Remove gear (8) and spacer (9).
Illustration 6 g00892965
3/12
329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine(SEB...
2020/4/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 8. Use Tooling (C) to remove retaining ring (10). Remove washer (11) and gear (12). Remove
bearing assembly (13) and washer (14).
9. Repeat Step 8 for the other two gear assemblies.
Illustration 7 g00892968
10. Remove retaining ring (15).
Illustration 8 g00892975
11. Remove carrier assembly (16).
4/12
329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine(SEB...
2020/4/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 9 g01389804
12. Use a suitable press to remove the shafts from carrier assembly (16).
Illustration 10 g00892977
13. Remove gear (17) and spacer (18).
Illustration 11 g00892997
5/12
329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine(SEB...
2020/4/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. 14. Use Tooling (D) and a suitable lifting device to remove planetary carrier (19). The weight of
planetary carrier (19) is approximately 48 kg (105 lb).
Illustration 12 g00893019
15. Remove retaining ring (21). Lift planetary carrier (19) off sun gear (20).
Illustration 13 g00896860
16. Drive spring pin (23) into planetary shaft (22).
Illustration 14 g00893043
6/12
329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine(SEB...
2020/4/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. 17. Remove planetary shaft (22). Use a suitable punch to remove spring pin (23) from planetary
shaft (22).
Illustration 15 g00896863
18. Remove washers (24) and bearing (25) from planetary gear (26).
19. Repeat Steps 16 through 18 for the other two planetary gears.
Illustration 16 g01842853
20. Remove gear (27). Remove spacer (27A).
Illustration 17 g01842974
7/12
329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine(SEB...
2020/4/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. 21. Use two people to remove carrier assembly (28). The weight of carrier assembly (28) is
approximately 38 kg (85 lb).
Illustration 18 g01843140
22. Drive spring pin (30) into shaft (29).
Illustration 19 g00893658
23. Remove shaft (29). Use a suitable punch to remove spring pin (30) from shaft (29).
Illustration 20 g00893674
24. Remove washers (31) and bearings (32) from planetary gear (33).
8/12
329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine(SEB...
2020/4/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. 25. Repeat Steps 22 through 24 for the other three planetary gears.
Illustration 21 g01208300
26. Fasten Tooling (E) and a suitable lifting device to ring gear (34), as shown. Remove ring
gear (34) from sprocket housing (35). The weight of ring gear (34) is approximately 66 kg
(146 lb).
Illustration 22 g01208542
27. Remove O-ring seal (36) from sprocket housing (35).
Illustration 23 g01208553
9/12
329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine(SEB...
2020/4/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. 28. Remove bolts (37) from coupling gear (38).
Illustration 24 g01208572
29. Install suitable forcing bolts (39) in coupling gear (38). Tighten the forcing bolts evenly in
order to loosen coupling gear (38). Remove the coupling gear from the motor housing.
Illustration 25 g01208578
Illustration 26 g01208625
30. Remove shims (40) from the motor housing.
10/12
329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine(S...
2020/4/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Note: Inner cones and outer bearing cones (42) are a slip fit on the motor housing. While
you remove sprocket housing (35) from the motor housing, inner bearing cone (42) may
stay with the sprocket housing or the inner bearing cone may stay on the motor housing.
31. Fasten Tooling (F) and a suitable lifting device to sprocket housing (35). Separate the
sprocket housing from the motor housing. The weight of sprocket housing (35) is
approximately 109 kg (240 lb).
Illustration 27 g01208626
32. Remove the locating pins from the motor housing.
33. Remove Duo-Cone seal (41) from the motor housing.
34. If inner bearing cone (42) remained on the motor housing, then remove the inner bearing
cone.
Illustration 28 g01208633
35. Remove Duo-Cone seal (43) from the sprocket housing.
36. If inner bearing cone (42) remained on the sprocket housing, then remove the inner bearing
cone.
37. Remove the bearing cups from the sprocket housing.
Thu Apr 30 08:40:12 UTC+0800 2020
11/12
329D2 L Excavators WDT00001-UP (MACHINE) POWERED BY C7.1 Engine(S...
2020/4/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...