This document provides instructions for removing and installing various engine components on a Caterpillar 329D L and 329D LN excavator, including:
- Removing and installing the engine oil pan, which involves draining the oil, removing bolts and the pan, cleaning surfaces, applying sealant, and reinstalling with new bolts and gasket.
- Removing and installing piston cooling jets by removing and replacing bolts to hold the jets in place.
- Procedures for removing pistons and connecting rods by identifying parts, removing caps and bolts, and pushing components out of the engine block.
Caterpillar cat 304 e2cr mini hydraulic excavator (prefix kc4) service repair...ufjjskekkmed
This document provides instructions for removing and installing various engine components on a Caterpillar 304E2CR Mini Hydraulic Excavator including:
- Crankshaft rear seal carrier
- Flywheel housing
- Crankshaft pulley
- Crankshaft front seal
- Idler gear
- Housing (front)
- Valve mechanism cover
The procedures provide detailed illustrations and steps for removal and installation of each component, including any required tools and torque specifications. Safety and maintenance notes are also included.
Caterpillar cat 329 d2 and 329d2l excavator (prefix thw) service repair manua...udjfjjsekekkem
The document provides instructions for removing and installing a flywheel on a C7.1 engine used in 329D2 and 329D2L excavators. The flywheel removal procedure involves removing mounting bolts using guide studs for support, then inspecting the flywheel and ring gear. The flywheel installation procedure specifies cleaning and heating the ring gear, positioning the flywheel using guide studs and lifting devices, and tightening mounting bolts to the specified torque. A separate section provides instructions for removing the crankshaft rear seal, which involves using a Torx socket to remove mounting screws and discarding the sealed assembly.
The document provides instructions for removing and installing a turbocharger and fuel injection pump gear on a Caterpillar 320D2 excavator. The removal steps include disconnecting hoses, removing bolts and tubes, and taking out the turbocharger. The installation involves cleaning parts, installing new seals, placing the gear on the pump shaft, locking the pump, and reconnecting all tubes and hoses. The process is completed by lubricating the gears.
Caterpillar cat 312 d excavator (prefix kes) service repair manual (kes00001 ...fksjksmmde
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312D excavator with a C4.2 engine. It describes how to remove the electric starting motor, flywheel, ring gear, and housing bolts. It then explains how to install the housing using a link bracket and driver group, and reinstall the flywheel and starting motor.
The document provides instructions for removing and installing the engine oil pump on a Caterpillar C7.1 engine. It describes removing the oil pan, suction pipe, brackets, and bolts to detach the pump. Instructions are given to disassemble the pump components if needed. Reinstallation involves cleaning parts, installing gaskets and dowels, and tightening bolts in the specified sequence and torque. Technicians are advised to replace the entire pump assembly if any parts are worn or damaged.
Caterpillar cat 320 d lrr excavator (prefix dhe) service repair manual (dhe00...fjsekdmmeed
This document provides instructions for removing, disassembling, assembling, and installing the engine oil pump and water pump on a Caterpillar 320D LRR excavator with a C6.4 engine. The oil pump removal process involves taking off the front housing cover and various gears. The water pump removal requires removing the belt and pump pulley. Both pumps are disassembled by removing mounting components using various tools. Reassembly follows the reverse order and procedures provide guidance on cleaning, inspection and installation of seals.
Caterpillar cat 323 d excavator (prefix zmf) service repair manual (zmf00001 ...fjskksmem
The document provides instructions for removing and installing various engine components on a Caterpillar 323D excavator. It describes in detail how to remove and install the crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The procedures involve using various tools to remove fasteners and other parts, taking care to keep components clean and ensure proper alignment of gears.
Caterpillar cat 304 cr mini hydraulic excavator (prefix nad) service repair m...fikskkdmmd1
This document provides instructions for disassembling a travel motor on a 304CR Mini Hydraulic Excavator. The disassembly procedure involves 27 steps and includes removing plates, barrels, pistons, gears, seals, and other components. Special tools are required and precautions around fluid containment and cleanliness are noted. Detailed illustrations accompany each step.
Caterpillar cat 304 e2cr mini hydraulic excavator (prefix kc4) service repair...ufjjskekkmed
This document provides instructions for removing and installing various engine components on a Caterpillar 304E2CR Mini Hydraulic Excavator including:
- Crankshaft rear seal carrier
- Flywheel housing
- Crankshaft pulley
- Crankshaft front seal
- Idler gear
- Housing (front)
- Valve mechanism cover
The procedures provide detailed illustrations and steps for removal and installation of each component, including any required tools and torque specifications. Safety and maintenance notes are also included.
Caterpillar cat 329 d2 and 329d2l excavator (prefix thw) service repair manua...udjfjjsekekkem
The document provides instructions for removing and installing a flywheel on a C7.1 engine used in 329D2 and 329D2L excavators. The flywheel removal procedure involves removing mounting bolts using guide studs for support, then inspecting the flywheel and ring gear. The flywheel installation procedure specifies cleaning and heating the ring gear, positioning the flywheel using guide studs and lifting devices, and tightening mounting bolts to the specified torque. A separate section provides instructions for removing the crankshaft rear seal, which involves using a Torx socket to remove mounting screws and discarding the sealed assembly.
The document provides instructions for removing and installing a turbocharger and fuel injection pump gear on a Caterpillar 320D2 excavator. The removal steps include disconnecting hoses, removing bolts and tubes, and taking out the turbocharger. The installation involves cleaning parts, installing new seals, placing the gear on the pump shaft, locking the pump, and reconnecting all tubes and hoses. The process is completed by lubricating the gears.
Caterpillar cat 312 d excavator (prefix kes) service repair manual (kes00001 ...fksjksmmde
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312D excavator with a C4.2 engine. It describes how to remove the electric starting motor, flywheel, ring gear, and housing bolts. It then explains how to install the housing using a link bracket and driver group, and reinstall the flywheel and starting motor.
The document provides instructions for removing and installing the engine oil pump on a Caterpillar C7.1 engine. It describes removing the oil pan, suction pipe, brackets, and bolts to detach the pump. Instructions are given to disassemble the pump components if needed. Reinstallation involves cleaning parts, installing gaskets and dowels, and tightening bolts in the specified sequence and torque. Technicians are advised to replace the entire pump assembly if any parts are worn or damaged.
Caterpillar cat 320 d lrr excavator (prefix dhe) service repair manual (dhe00...fjsekdmmeed
This document provides instructions for removing, disassembling, assembling, and installing the engine oil pump and water pump on a Caterpillar 320D LRR excavator with a C6.4 engine. The oil pump removal process involves taking off the front housing cover and various gears. The water pump removal requires removing the belt and pump pulley. Both pumps are disassembled by removing mounting components using various tools. Reassembly follows the reverse order and procedures provide guidance on cleaning, inspection and installation of seals.
Caterpillar cat 323 d excavator (prefix zmf) service repair manual (zmf00001 ...fjskksmem
The document provides instructions for removing and installing various engine components on a Caterpillar 323D excavator. It describes in detail how to remove and install the crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The procedures involve using various tools to remove fasteners and other parts, taking care to keep components clean and ensure proper alignment of gears.
Caterpillar cat 304 cr mini hydraulic excavator (prefix nad) service repair m...fikskkdmmd1
This document provides instructions for disassembling a travel motor on a 304CR Mini Hydraulic Excavator. The disassembly procedure involves 27 steps and includes removing plates, barrels, pistons, gears, seals, and other components. Special tools are required and precautions around fluid containment and cleanliness are noted. Detailed illustrations accompany each step.
The document provides step-by-step instructions for disassembling the final drive of a 329DL excavator. It begins by removing the final drive assembly and placing it on a repair stand. Key steps include removing the cover, gears, shafts, carriers, and planetary gears. Tools needed are listed. Detailed illustrations accompany each step to show how to remove each component. Cleanliness is emphasized to prevent dirt from entering during disassembly.
Caterpillar cat 938 g ii wheel loader (prefix phn) service repair manual (phn...fjsjjekdkme
The document provides instructions for disassembling and assembling the transmission oil pump and relief valve (transmission hydraulic control) for a Caterpillar 938G II wheel loader. It includes detailed steps and illustrations for removing parts like gears, bearings, seals and covers. Tools required are also listed. The document is from a Caterpillar service manual and aims to guide maintenance technicians in properly servicing these components.
Caterpillar cat 312 d l excavator (prefix xgk) service repair manual (xgk0000...pfiskdmjekm
This document provides instructions for removing and installing the crankshaft pulley and front seal on a Caterpillar C4.2 engine. It describes:
1) Using various tools like pullers and sockets to remove the pulley nut, washer, and pulley.
2) Removing the wear sleeve from the pulley if needed by tapping with a chisel.
3) Heating the wear sleeve and installing it on the pulley with a driver group.
4) Reinstalling the pulley, washer, and nut and tightening to the specified torque.
Caterpillar cat 312 d excavator (prefix lrk) service repair manual (lrk00001 ...fksjksmmde
The document provides instructions for removing and installing the valve mechanism cover base on a Caterpillar C4.2 engine. It describes:
1) Removing clips, disconnecting harnesses, and loosening nuts to detach the electronic unit injectors from the cover base.
2) Installing a new gasket, positioning the cover base, and reattaching the electronic unit injectors by connecting harnesses and tightening nuts.
3) The document is part of a service manual for repairing a 312D Excavator with a C4.2 engine. It contains detailed steps and illustrations for the removal and installation process.
Caterpillar cat 329 d2 and 329d2l excavator (prefix rga) service repair manua...udjfjjsekekkem
This document provides instructions for disassembling and assembling the swing motor of a Caterpillar 329D2 excavator. The disassembly procedure involves removing 27 parts in a specific order, taking care with spring-loaded components. The assembly procedure similarly involves installing the 27 parts in reverse order and also notes that O-rings, gaskets, and seals should be replaced and components should be cleaned before assembly. Torque specifications and required tools are provided for referenced steps.
Caterpillar cat 312 b excavator (prefix 2kw) service repair manual (2kw00001 ...fjsekksmemm
The document provides instructions for removing and installing the valve mechanism cover on a 3054 engine. The key steps are:
1. Remove all bolts securing the valve mechanism cover to the cylinder head.
2. Remove the valve mechanism cover and gasket.
3. Install a new gasket and valve mechanism cover, securing it with the bolts. Tighten the bolts to the specified torque.
The instructions emphasize keeping parts clean and containing fluids to prevent contamination.
Caterpillar cat 272 d skid steer loader (prefix b5w) service repair manual (b...fujsekkskemm
This document provides instructions for removing and installing various components of a C3.8 engine, including the fuel injection pump, electronic unit injectors, turbocharger, mass air flow pressure sensor, and exhaust gas recirculation valve. The procedures include using specific tools, applying anti-seize compound to bolts, and torquing fasteners to the specified values. Cautions are provided about working on high pressure fuel systems and properly purging fuel before disassembly.
Caterpillar cat 246 d skid steer loader (prefix hmr) service repair manual (h...fjjsefkkertsemme
This document provides instructions for removing and installing a fuel injection pump on a 246D Skid Steer Loader powered by a C3.3B engine. The procedure involves disconnecting fuel lines, removing mounting bolts and nuts, and cleaning components. When installing, new gasket shims are used and bolts are tightened to the specified torques. Special care must be taken when removing the spring-loaded fuel injection pump.
Caterpillar cat 304 e2cr mini hydraulic excavator (prefix gc5) service repair...ufjsjjkksemme
The document provides instructions for removing and installing various engine components on a 304E2 CR Mini Hydraulic Excavator including:
- Exhaust gas recirculation valve
- Exhaust manifold
- Diesel particulate filter
- Inlet manifold
The procedures describe removing mounting bolts and disconnecting sensors/lines before removing the components, and installing in the reverse order while applying anti-seize compound and torquing bolts to the specified values. Safety precautions are provided to prevent burns from hot components.
Caterpillar cat 311 b track type excavator (prefix 2ls) service repair manual...fjskefkemms
This document provides instructions for servicing components of a 311B excavator engine, including:
1) Instructions for assembling the rocker shaft, including the components and installation steps.
2) Instructions for installing the rocker shaft and pushrods, including torque specifications.
3) Instructions for removing the cylinder head, including removal steps and safety notices.
Caterpillar Cat 329D L Excavator (Prefix EBM) Service Repair Manual (EBM00001...shudun96087
1) The document provides instructions for removing and installing pistons and connecting rods on a Caterpillar C7 engine.
2) Key steps include removing the cylinder head, oil pump, and piston cooling jets before removing the pistons and connecting rods. Pistons and connecting rods must be kept with their respective caps and cylinders.
3) Reassembly involves pressing in new connecting rod bearings, installing piston rings, inserting the piston and pin, and reinstalling the components. Proper identification and orientation is important for correct reassembly.
1) The document provides instructions for removing and installing pistons and connecting rods on a Caterpillar C7 engine.
2) Key steps include removing the cylinder head, oil pump, and piston cooling jets before removing the pistons and connecting rods. Pistons and connecting rods must be kept with their respective caps and cylinders.
3) Reassembly involves pressing in new connecting rod bearings, installing piston rings, inserting the piston and pin, and reinstalling the components. Proper identification and orientation is important for correct reassembly.
The document provides instructions for removing and installing pistons and connecting rods on a Caterpillar C7 engine. Key steps include:
1. Marking connecting rods and caps before removal to ensure proper reinstallation.
2. Removing bolts and caps to separate connecting rods from pistons.
3. Reassembling pistons and connecting rods, ensuring components are installed in their original locations and orientations. Proper ring installation and bearing fitting are critical.
Caterpillar Cat 329D L Excavator (Prefix EBM) Service Repair Manual (EBM00001...yfbr995309
1) The document provides instructions for removing and installing pistons and connecting rods on a Caterpillar C7 engine.
2) Key steps include removing the cylinder head, oil pump, and piston cooling jets before removing the pistons and connecting rods. Pistons and connecting rods must be kept with their identifying marks and installed in the original locations.
3) Reassembly involves pressing in new connecting rod bearings, installing piston rings, inserting the piston and pin with retaining rings, and reinstalling the components. Proper clearances and orientation are checked during assembly.
Caterpillar Cat 329D L Excavator (Prefix EBM) Service Repair Manual (EBM00001...kesi7153062
1) The document provides instructions for removing and installing pistons and connecting rods on a Caterpillar C7 engine.
2) Key steps include removing the cylinder head, oil pump, and piston cooling jets before removing the pistons and connecting rods. Pistons and connecting rods must be kept with their identifying marks and installed in the original locations.
3) Reassembly involves pressing new bearings into the connecting rods, installing piston rings, and reinstalling the pistons and connecting rods back into the engine.
1) The document provides instructions for removing and installing pistons and connecting rods on a Caterpillar C7 engine.
2) Key steps include removing the cylinder head, oil pump, and piston cooling jets before removing the pistons and connecting rods. Pistons and connecting rods must be kept with their identifying marks and installed in the original locations.
3) Reassembly involves pressing in new connecting rod bearings, installing piston rings, inserting the piston and pin with retaining rings, and reinstalling the components in reverse order. Proper heating and cooling procedures are specified for the connecting rod bearings.
Caterpillar Cat 329DLN Excavator (Prefix SCY) Service Repair Manual (SCY00001...shudun96087
This document provides instructions for removing the engine oil filter base and oil cooler from a Caterpillar 329D L and 329D LN excavator. The procedure involves using a strap wrench to remove the engine oil filter. Then remove bolts to detach the oil filter base and oil cooler. Safety precautions are outlined such as keeping parts clean and containing fluids. Tools required are listed.
This document provides instructions for removing and installing engine components on a Caterpillar 329D L & 329D LN Excavator, including:
- Removing and installing inlet and exhaust valves
- Removing and installing inlet and exhaust valve guides
- Removing and installing inlet and exhaust valve seat inserts
- Removing the engine oil filter base and oil cooler
- Disassembling the engine oil filter base
The document contains detailed step-by-step instructions and illustrations for each procedure. Safety notices are provided throughout to warn technicians of potential injury risks.
This document provides instructions for removing and installing engine components on a 329D L & 329D LN Excavator including:
- Removing and installing inlet and exhaust valves
- Removing and installing inlet and exhaust valve guides
- Removing and installing inlet and exhaust valve seat inserts
- Removing the engine oil filter base and oil cooler
- Disassembling the engine oil filter base
The document contains detailed step-by-step instructions and illustrations for each procedure. Safety notices are provided throughout to warn technicians of potential injury risks.
This document provides instructions for removing and installing engine components on a 329D L & 329D LN Excavator including:
- Removing and installing inlet and exhaust valves
- Removing and installing inlet and exhaust valve guides
- Removing and installing inlet and exhaust valve seat inserts
- Removing the engine oil filter base and oil cooler
- Disassembling the engine oil filter base
The document contains detailed step-by-step instructions and illustrations for each procedure. Safety notices are provided throughout to warn technicians of potential injury risks.
Caterpillar Cat 329DLN Excavator (Prefix SCY) Service Repair Manual (SCY00001...cnp692569
This document provides instructions for removing and installing engine components on a Caterpillar 329D L & 329D LN Excavator, including:
- Removing and installing inlet and exhaust valves
- Removing and installing inlet and exhaust valve guides
- Removing and installing inlet and exhaust valve seat inserts
- Removing the engine oil filter base and oil cooler
- Disassembling the engine oil filter base
The document contains detailed step-by-step instructions and illustrations for each procedure. Safety notices are provided throughout to warn technicians of potential injury risks.
Caterpillar Cat 329DLN Excavator (Prefix SCY) Service Repair Manual (SCY00001...kesi7153062
This document provides instructions for removing and installing engine components on a 329D L & 329D LN Excavator including:
- Removing and installing inlet and exhaust valves
- Removing and installing inlet and exhaust valve guides
- Removing and installing inlet and exhaust valve seat inserts
- Removing the engine oil filter base and oil cooler
- Disassembling the engine oil filter base
The document contains detailed step-by-step instructions and illustrations for each procedure. Safety notices are provided throughout to warn technicians of potential injury risks.
The document provides step-by-step instructions for disassembling the final drive of a 329DL excavator. It begins by removing the final drive assembly and placing it on a repair stand. Key steps include removing the cover, gears, shafts, carriers, and planetary gears. Tools needed are listed. Detailed illustrations accompany each step to show how to remove each component. Cleanliness is emphasized to prevent dirt from entering during disassembly.
Caterpillar cat 938 g ii wheel loader (prefix phn) service repair manual (phn...fjsjjekdkme
The document provides instructions for disassembling and assembling the transmission oil pump and relief valve (transmission hydraulic control) for a Caterpillar 938G II wheel loader. It includes detailed steps and illustrations for removing parts like gears, bearings, seals and covers. Tools required are also listed. The document is from a Caterpillar service manual and aims to guide maintenance technicians in properly servicing these components.
Caterpillar cat 312 d l excavator (prefix xgk) service repair manual (xgk0000...pfiskdmjekm
This document provides instructions for removing and installing the crankshaft pulley and front seal on a Caterpillar C4.2 engine. It describes:
1) Using various tools like pullers and sockets to remove the pulley nut, washer, and pulley.
2) Removing the wear sleeve from the pulley if needed by tapping with a chisel.
3) Heating the wear sleeve and installing it on the pulley with a driver group.
4) Reinstalling the pulley, washer, and nut and tightening to the specified torque.
Caterpillar cat 312 d excavator (prefix lrk) service repair manual (lrk00001 ...fksjksmmde
The document provides instructions for removing and installing the valve mechanism cover base on a Caterpillar C4.2 engine. It describes:
1) Removing clips, disconnecting harnesses, and loosening nuts to detach the electronic unit injectors from the cover base.
2) Installing a new gasket, positioning the cover base, and reattaching the electronic unit injectors by connecting harnesses and tightening nuts.
3) The document is part of a service manual for repairing a 312D Excavator with a C4.2 engine. It contains detailed steps and illustrations for the removal and installation process.
Caterpillar cat 329 d2 and 329d2l excavator (prefix rga) service repair manua...udjfjjsekekkem
This document provides instructions for disassembling and assembling the swing motor of a Caterpillar 329D2 excavator. The disassembly procedure involves removing 27 parts in a specific order, taking care with spring-loaded components. The assembly procedure similarly involves installing the 27 parts in reverse order and also notes that O-rings, gaskets, and seals should be replaced and components should be cleaned before assembly. Torque specifications and required tools are provided for referenced steps.
Caterpillar cat 312 b excavator (prefix 2kw) service repair manual (2kw00001 ...fjsekksmemm
The document provides instructions for removing and installing the valve mechanism cover on a 3054 engine. The key steps are:
1. Remove all bolts securing the valve mechanism cover to the cylinder head.
2. Remove the valve mechanism cover and gasket.
3. Install a new gasket and valve mechanism cover, securing it with the bolts. Tighten the bolts to the specified torque.
The instructions emphasize keeping parts clean and containing fluids to prevent contamination.
Caterpillar cat 272 d skid steer loader (prefix b5w) service repair manual (b...fujsekkskemm
This document provides instructions for removing and installing various components of a C3.8 engine, including the fuel injection pump, electronic unit injectors, turbocharger, mass air flow pressure sensor, and exhaust gas recirculation valve. The procedures include using specific tools, applying anti-seize compound to bolts, and torquing fasteners to the specified values. Cautions are provided about working on high pressure fuel systems and properly purging fuel before disassembly.
Caterpillar cat 246 d skid steer loader (prefix hmr) service repair manual (h...fjjsefkkertsemme
This document provides instructions for removing and installing a fuel injection pump on a 246D Skid Steer Loader powered by a C3.3B engine. The procedure involves disconnecting fuel lines, removing mounting bolts and nuts, and cleaning components. When installing, new gasket shims are used and bolts are tightened to the specified torques. Special care must be taken when removing the spring-loaded fuel injection pump.
Caterpillar cat 304 e2cr mini hydraulic excavator (prefix gc5) service repair...ufjsjjkksemme
The document provides instructions for removing and installing various engine components on a 304E2 CR Mini Hydraulic Excavator including:
- Exhaust gas recirculation valve
- Exhaust manifold
- Diesel particulate filter
- Inlet manifold
The procedures describe removing mounting bolts and disconnecting sensors/lines before removing the components, and installing in the reverse order while applying anti-seize compound and torquing bolts to the specified values. Safety precautions are provided to prevent burns from hot components.
Caterpillar cat 311 b track type excavator (prefix 2ls) service repair manual...fjskefkemms
This document provides instructions for servicing components of a 311B excavator engine, including:
1) Instructions for assembling the rocker shaft, including the components and installation steps.
2) Instructions for installing the rocker shaft and pushrods, including torque specifications.
3) Instructions for removing the cylinder head, including removal steps and safety notices.
Caterpillar Cat 329D L Excavator (Prefix EBM) Service Repair Manual (EBM00001...shudun96087
1) The document provides instructions for removing and installing pistons and connecting rods on a Caterpillar C7 engine.
2) Key steps include removing the cylinder head, oil pump, and piston cooling jets before removing the pistons and connecting rods. Pistons and connecting rods must be kept with their respective caps and cylinders.
3) Reassembly involves pressing in new connecting rod bearings, installing piston rings, inserting the piston and pin, and reinstalling the components. Proper identification and orientation is important for correct reassembly.
1) The document provides instructions for removing and installing pistons and connecting rods on a Caterpillar C7 engine.
2) Key steps include removing the cylinder head, oil pump, and piston cooling jets before removing the pistons and connecting rods. Pistons and connecting rods must be kept with their respective caps and cylinders.
3) Reassembly involves pressing in new connecting rod bearings, installing piston rings, inserting the piston and pin, and reinstalling the components. Proper identification and orientation is important for correct reassembly.
The document provides instructions for removing and installing pistons and connecting rods on a Caterpillar C7 engine. Key steps include:
1. Marking connecting rods and caps before removal to ensure proper reinstallation.
2. Removing bolts and caps to separate connecting rods from pistons.
3. Reassembling pistons and connecting rods, ensuring components are installed in their original locations and orientations. Proper ring installation and bearing fitting are critical.
Caterpillar Cat 329D L Excavator (Prefix EBM) Service Repair Manual (EBM00001...yfbr995309
1) The document provides instructions for removing and installing pistons and connecting rods on a Caterpillar C7 engine.
2) Key steps include removing the cylinder head, oil pump, and piston cooling jets before removing the pistons and connecting rods. Pistons and connecting rods must be kept with their identifying marks and installed in the original locations.
3) Reassembly involves pressing in new connecting rod bearings, installing piston rings, inserting the piston and pin with retaining rings, and reinstalling the components. Proper clearances and orientation are checked during assembly.
Caterpillar Cat 329D L Excavator (Prefix EBM) Service Repair Manual (EBM00001...kesi7153062
1) The document provides instructions for removing and installing pistons and connecting rods on a Caterpillar C7 engine.
2) Key steps include removing the cylinder head, oil pump, and piston cooling jets before removing the pistons and connecting rods. Pistons and connecting rods must be kept with their identifying marks and installed in the original locations.
3) Reassembly involves pressing new bearings into the connecting rods, installing piston rings, and reinstalling the pistons and connecting rods back into the engine.
1) The document provides instructions for removing and installing pistons and connecting rods on a Caterpillar C7 engine.
2) Key steps include removing the cylinder head, oil pump, and piston cooling jets before removing the pistons and connecting rods. Pistons and connecting rods must be kept with their identifying marks and installed in the original locations.
3) Reassembly involves pressing in new connecting rod bearings, installing piston rings, inserting the piston and pin with retaining rings, and reinstalling the components in reverse order. Proper heating and cooling procedures are specified for the connecting rod bearings.
Caterpillar Cat 329DLN Excavator (Prefix SCY) Service Repair Manual (SCY00001...shudun96087
This document provides instructions for removing the engine oil filter base and oil cooler from a Caterpillar 329D L and 329D LN excavator. The procedure involves using a strap wrench to remove the engine oil filter. Then remove bolts to detach the oil filter base and oil cooler. Safety precautions are outlined such as keeping parts clean and containing fluids. Tools required are listed.
This document provides instructions for removing and installing engine components on a Caterpillar 329D L & 329D LN Excavator, including:
- Removing and installing inlet and exhaust valves
- Removing and installing inlet and exhaust valve guides
- Removing and installing inlet and exhaust valve seat inserts
- Removing the engine oil filter base and oil cooler
- Disassembling the engine oil filter base
The document contains detailed step-by-step instructions and illustrations for each procedure. Safety notices are provided throughout to warn technicians of potential injury risks.
This document provides instructions for removing and installing engine components on a 329D L & 329D LN Excavator including:
- Removing and installing inlet and exhaust valves
- Removing and installing inlet and exhaust valve guides
- Removing and installing inlet and exhaust valve seat inserts
- Removing the engine oil filter base and oil cooler
- Disassembling the engine oil filter base
The document contains detailed step-by-step instructions and illustrations for each procedure. Safety notices are provided throughout to warn technicians of potential injury risks.
This document provides instructions for removing and installing engine components on a 329D L & 329D LN Excavator including:
- Removing and installing inlet and exhaust valves
- Removing and installing inlet and exhaust valve guides
- Removing and installing inlet and exhaust valve seat inserts
- Removing the engine oil filter base and oil cooler
- Disassembling the engine oil filter base
The document contains detailed step-by-step instructions and illustrations for each procedure. Safety notices are provided throughout to warn technicians of potential injury risks.
Caterpillar Cat 329DLN Excavator (Prefix SCY) Service Repair Manual (SCY00001...cnp692569
This document provides instructions for removing and installing engine components on a Caterpillar 329D L & 329D LN Excavator, including:
- Removing and installing inlet and exhaust valves
- Removing and installing inlet and exhaust valve guides
- Removing and installing inlet and exhaust valve seat inserts
- Removing the engine oil filter base and oil cooler
- Disassembling the engine oil filter base
The document contains detailed step-by-step instructions and illustrations for each procedure. Safety notices are provided throughout to warn technicians of potential injury risks.
Caterpillar Cat 329DLN Excavator (Prefix SCY) Service Repair Manual (SCY00001...kesi7153062
This document provides instructions for removing and installing engine components on a 329D L & 329D LN Excavator including:
- Removing and installing inlet and exhaust valves
- Removing and installing inlet and exhaust valve guides
- Removing and installing inlet and exhaust valve seat inserts
- Removing the engine oil filter base and oil cooler
- Disassembling the engine oil filter base
The document contains detailed step-by-step instructions and illustrations for each procedure. Safety notices are provided throughout to warn technicians of potential injury risks.
This document provides instructions for installing a fuel injection pump gear on a 320D2 excavator. The steps include:
1. Ensuring the crankshaft and camshaft are locked in position using special tools
2. Aligning the timing marks on the fuel pump gear, camshaft gear, and crankshaft gear
3. Installing the fuel pump gear and tightening the nut while removing backlash
4. Unlocking the fuel injection pump and installing plugs and seals
5. Checking gear backlash and installing the front cover
The document provides instructions for removing a side-mounted turbocharger from a Caterpillar 320D2 excavator engine. The steps include disconnecting hoses and tube assemblies from the turbocharger, removing the exhaust out tube assembly and elbow if necessary, and removing the banjo bolt from a tube assembly. Plugs and caps must be used to seal any open ports during removal.
This document provides instructions for installing a fuel injection pump gear on a 320D2 excavator. The steps include:
1. Ensuring the crankshaft and camshaft are locked in position using special tools
2. Aligning the timing marks on the fuel pump gear, camshaft gear, and crankshaft gear
3. Installing the fuel pump gear and tightening the nut while removing backlash
4. Unlocking the fuel injection pump and installing plugs and seals
5. Checking gear backlash and installing the front cover
This document provides instructions for installing a fuel injection pump gear on a 320D2 excavator. The steps include:
1. Ensuring the crankshaft and camshaft are locked in position using special tools
2. Aligning the timing marks on the fuel pump gear, camshaft gear, and crankshaft gear
3. Installing the fuel pump gear and tightening the nut while removing backlash
4. Unlocking the fuel injection pump and installing plugs and seals
5. Checking gear backlash and installing the front cover
This document provides instructions for installing a fuel injection pump gear on a 320D2 excavator. The steps include:
1. Ensuring the number one piston is at top dead center and locking the crankshaft and camshaft positions.
2. Installing the fuel pump gear on the fuel injection pump shaft and checking timing marks are aligned.
3. Installing a washer, nut and tightening to specified torques to secure the gear.
4. Unlocking the fuel injection pump and installing plugs and seals.
This document provides instructions for removing and installing a side-mounted turbocharger on a Caterpillar C7.1 engine. The steps include disconnecting hoses and tube assemblies from the turbocharger, removing bolts, and removing the turbocharger unit from the engine. New seals, washers, and bolts are used when reinstalling the turbocharger.
The document provides instructions for removing and installing a fuel injection pump gear on a Caterpillar 320D2 excavator engine. Key steps include:
1. Using tools to lock the crankshaft and camshaft in position.
2. Ensuring timing marks are aligned and gears mesh correctly before installing the fuel pump gear.
3. Tightening the nut on the fuel pump gear shaft and checking backlash is within specifications.
4. Unlocking the fuel injection pump and removing locking tools before starting the engine.
The document provides instructions for removing and installing a fuel injection pump gear on a Caterpillar 320D2 excavator engine. Key steps include:
1. Using tools to lock the crankshaft and camshaft in position.
2. Ensuring timing marks are aligned and gears mesh correctly before installing the fuel pump gear.
3. Tightening the nut on the fuel pump gear shaft and checking backlash is within specifications.
4. Unlocking the fuel injection pump and removing locking tools before starting the engine.
Similar to Caterpillar cat 329 d ln excavator (prefix ebm) service repair manual (ebm00001 and up) (20)
Caterpillar cat 320 n track type excavator (prefix 2dl) service repair manual...ddkkddm
This document provides instructions for removing and installing valve stem seals on Caterpillar 320, 320L, and 320N track-type excavators. The procedure involves using a seal pick tool to remove the old seals from the valve guides and install new seals. Technicians are instructed to keep all parts clean and coat the new seals with engine oil during installation.
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. The procedure involves using specialty tools to compress the valve springs so that the valves, springs, and related components can be safely accessed and removed or installed one piston at a time. Proper tool use and safety precautions are emphasized to avoid injury from released spring forces.
The document provides instructions for removing the fuel injection pump from a Caterpillar 320D L excavator with a C6.4 engine. It lists the required tools and safety notices, then gives a step-by-step procedure involving disconnecting fuel lines and harness assemblies, removing mounting hardware, and taking off the pump while keeping identification marks aligned for installation. Cleanliness is emphasized throughout to prevent contaminants from entering the system.
Caterpillar cat 320 l track type excavator (prefix 2dl) service repair manual...ddkkddm
This document provides instructions for installing and removing various engine components on Caterpillar 320, 320L, and 320N track-type excavators, including:
- Removing and installing inlet and exhaust valve seals
- Removing the engine oil filter base
- Installing the engine oil filter base
- Removing the engine oil cooler
- Disassembling the engine oil cooler
- Reassembling the engine oil cooler
- Installing the engine oil cooler
The summaries provide the main steps and components involved in each procedure.
This document provides instructions for connecting a separated track on a 320D LN excavator. It describes using hydraulic tools and pins to lift the track into position and connect the master pin. Cleanliness is important to prevent dirt from entering during reassembly. The track must be positioned correctly and tools are needed if the pin cannot be manually installed.
Caterpillar cat 320 d2 l excavator (prefix gba) service repair manual (gba000...ddkkddm
This document provides instructions for removing the fuel injector from a Caterpillar 320D2 excavator engine. It lists the required tools which include a fuel injector puller and capping kit. The procedure involves disconnecting fuel lines from the injector, plugging the injector, removing mounting bolts and clamps, and using a puller tool to remove the fuel injector from the engine. Care must be taken to contain any fluids and ensure all parts are clean.
Caterpillar cat 320 d2 l excavator (prefix dnp) service repair manual (dnp000...ddkkddm
The document provides instructions for assembling and installing the swing drive on a 320D2 excavator. It describes 22 steps to assemble components like bearings, gears, housings and seals. The final step is to install the assembled swing drive and refer to other instructions for installing the swing motor.
This document provides instructions for removing the fuel injector from a Caterpillar 320D2 excavator engine. It lists the required tools which include a fuel injector puller and capping kit. The procedure involves disconnecting fuel lines from the injector, plugging the injector, removing mounting bolts and clamps, and using a puller tool to remove the fuel injector from the engine. Care must be taken to contain any fluids and ensure all parts are clean.
The document provides instructions for assembling and installing the swing drive on a 320D2 excavator. It describes 22 steps to assemble components like bearings, gears, housings and seals. The final step is to install the assembled swing drive and refer to other instructions for installing the swing motor.
Caterpillar cat 320 d ln excavator (prefix wbn) service repair manual (wbn000...ddkkddm
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D LN excavator with a C6.4 engine. It describes the required tools and safety precautions, and gives a step-by-step process for compressing the valve springs, removing old parts, and installing new parts in their proper positions and orientations. The document also provides specifications for inspecting valve components to ensure proper dimensions are met.
Caterpillar cat 320 d l excavator (prefix kgf) service repair manual (kgf0000...ddkkddm
This document provides instructions for disassembling and assembling the travel motor of a 320D L excavator. The disassembly process includes 27 steps to remove components like the head, fittings, seals, brake piston, plates, and barrel assembly. The assembly section outlines 13 steps including installing seals, keys, cam plate, springs, and piston shoe assemblies back into the barrel assembly and body of the travel motor. Special notices are provided regarding alignment marks, pressing components, and engaging the cam plate during assembly.
Caterpillar cat 320 d l excavator (prefix dhk) service repair manual (dhk0000...ddkkddm
This document provides instructions for removing and installing a boom cylinder on a 320D excavator. It includes:
1) Detailed steps to remove the boom cylinder such as releasing hydraulic pressure, removing mounting bolts and pins, and lifting the cylinder off the machine.
2) Information on required tools and torque specifications for reassembly.
3) The installation procedure which reverses the removal steps such as lifting the cylinder back into place, reinstalling pins and bolts, and reconnecting hydraulic lines.
Safety precautions are provided to relieve hydraulic pressure before disassembling cylinders. Torque specifications are included for correct reassembly.
Caterpillar cat 320 d l excavator (prefix a9f) service repair manual (a9f0000...ddkkddm
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. The procedure involves using specialty tools to compress the valve springs so that the valves, springs, and related components can be safely accessed and removed or installed one at a time. Proper cleaning and inspection of parts is emphasized to prevent premature wear. The work must be done with the pistons positioned correctly to avoid parts falling into the cylinders.
Caterpillar cat 320 d excavator (prefix kgf) service repair manual (kgf00001 ...ddkkddm
This document provides instructions for disassembling and assembling the travel motor of a 320D L Excavator. The disassembly process includes 27 steps to remove components like the head, fittings, seals, brake piston, plates, and barrel assembly. The assembly section outlines 13 steps including installing seals, keys, cam plate, springs, and piston shoe assemblies back into the barrel assembly and travel motor body. Special care must be taken to align parts and not allow components to separate during disassembly and assembly.
Caterpillar cat 320 d excavator (prefix dhk) service repair manual (dhk00001 ...ddkkddm
This document provides instructions for removing and installing the boom cylinder on a 320D and 320D L excavator. The procedure involves releasing hydraulic pressure, removing attachment points, and using lifting devices to maneuver the heavy cylinder. Special tools are required to remove pins connecting the cylinder. Torque specifications are provided for reinstallation. Safety precautions are described, such as relieving pressure before disassembly to avoid injury.
Caterpillar cat 320 track type excavator (prefix 2 dl) service repair manual ...ddkkddm
This document provides instructions for removing and installing valve stem seals on Caterpillar 320, 320L, and 320N track-type excavators. The procedure involves using a seal pick tool to remove the old seals from the valve guides and install new seals. Technicians are instructed to keep all parts clean and coat the new seals with engine oil during installation.
Caterpillar cat 320 s excavator (prefix 4 zj) service repair manual (4zj00460...ddkkddm
1. The document provides instructions for removing and installing final drives on 320-series excavators. It describes disconnecting hydraulic lines, removing mounting bolts, and using lifting tools to remove the final drives from the excavator.
2. Detailed steps are given for disassembling the final drives, including removing gears, carriers, seals, and other components. Alignment marks should be made for reassembly.
3. Reassembly involves cleaning parts, applying threadlock and lubricant, and torquing bolts to specification. Seals and bearings must be installed correctly to prevent damage.
Caterpillar cat 320 s excavator (prefix 3 xk) service repair manual (3xk00822...ddkkddm
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 320 excavator models. It describes the required tools and gives a step-by-step process including removing clips and pins, sliding tubes, and removing/installing parts like the governor, linkage, and seals using special tools. References are provided for more information on governors and linkage inspection procedures.
Caterpillar cat 320 n excavator (prefix 4 zj) service repair manual (4zj00460...ddkkddm
1. The document provides instructions for removing and installing final drives on 320-series excavators. It describes disconnecting hydraulic lines, removing mounting bolts, and using hoists to lift heavy components like the final drive, ring gear, and carrier assemblies.
2. Detailed steps are given for disassembling the final drive components, including removing planetary gears, sun gears, and thrust washers. Special tools and alignment marks are used to aid reassembly.
3. Reassembly involves cleaning components, applying threadlock and anti-seize compound, and adjusting bearing preload with shims to achieve the correct specifications. Duo-Cone seals must be installed without damage to provide sealing between housings.
Caterpillar cat 320 n excavator (prefix 3 xk) service repair manual (3xk00822...ddkkddm
This document provides instructions for removing and installing a fuel injection control linkage on Caterpillar 320 excavator models. The removal procedure involves taking out the rocker shaft and pushrods, then removing clips and a clevis pin connecting the governor to the linkage. Installation requires reattaching the linkage with bolts and setting brackets, then inserting the clevis pin and clip using special tools. Compressing injector springs with another tool is also part of the installation process.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
Automotive Engine Valve Manufacturing Plant Project Report.pptxSmith Anderson
The report provides a complete roadmap for setting up an Automotive Engine Valve. It covers a comprehensive market overview to micro-level information such as unit operations involved, raw material requirements, utility requirements, infrastructure requirements, machinery and technology requirements, manpower requirements, packaging requirements, transportation requirements, etc.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 329D LN EXCAVATOR EBM
Configuration: 329D L & 329D LN Excavators EBM00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i05954439
Engine Oil Pan - Remove and Install
SMCS - 1302-010
Removal Procedure
Start By:
A. Remove the engine.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/3
329D L & 329D LN Excavators EBM00001-UP (MACHINE) POWERED BY C7 En...
2020/4/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. 1. Drain the engine oil into a suitable container for storage or disposal. Refer to Operation and
Maintenance Manual, "Engine Oil and Filter - Change" for the correct draining and filling
procedures.
Illustration 1 g01153839
Note: Do not pry or gouge the sealing surface of the engine oil pan. Use a rubber mallet to
tap lightly on the engine oil pan, if necessary.
2. Remove bolts (2) . Remove engine oil pan (1) and the gasket.
Installation Procedure
Table 1
Tool Part number Part Description Qty
A - Loctite 598 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3
329D L & 329D LN Excavators EBM00001-UP (MACHINE) POWERED BY C7 En...
2020/4/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 2 g03737518
1. Apply a bead of Tooling (A) to the areas shown in Illustration 2.
Illustration 3 g03738044
2. Position a new gasket and engine oil pan (1) on the cylinder block.
3. Install bolts (2) .
4. Tighten bolts (2) to a torque of 31 ± 3 N·m (23 ± 2 lb ft). Tighten the four bolts (2) in the
center and move outward in the direction shown in Illustration 3.
5. Repeat Step 4.
1. Fill the engine with engine oil to the correct level. Refer to Operation and Maintenance
Manual, "Engine Oil and Filter - Change" for the correct draining and filling procedures.
End By: Install the engine.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Apr 21 15:55:26 UTC+0800 2020
3/3
329D L & 329D LN Excavators EBM00001-UP (MACHINE) POWERED BY C7 En...
2020/4/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 329D LN EXCAVATOR EBM
Configuration: 329D L & 329D LN Excavators EBM00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02232665
Piston Cooling Jets - Remove and Install
SMCS - 1331-010
Removal Procedure
Start By:
a. Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
329D L & 329D LN Excavators EBM00001-UP (MACHINE) POWERED BY C7 En...
2020/4/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 1 g00987444
1. Remove bolt (2) and piston cooling jet (1) from each cylinder.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3
329D L & 329D LN Excavators EBM00001-UP (MACHINE) POWERED BY C7 En...
2020/4/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 2 g00987444
1. Position piston cooling jet (1) in the cylinder block. Install bolt (2). Tighten bolt (2) to a
torque of 28 ± 7 N·m (21 ± 5 lb ft).
End By:
a. Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump -
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Apr 21 15:56:23 UTC+0800 2020
3/3
329D L & 329D LN Excavators EBM00001-UP (MACHINE) POWERED BY C7 En...
2020/4/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 329D LN EXCAVATOR EBM
Configuration: 329D L & 329D LN Excavators EBM00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02232678
Pistons and Connecting Rods - Remove
SMCS - 1225-011
Removal Procedure
Start By:
a. Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
b. Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump -
Remove".
c. Remove the piston cooling jets. Refer to Disassembly and Assembly, "Piston Cooling Jets -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
329D L & 329D LN Excavators EBM00001-UP (MACHINE) POWERED BY C7 En...
2020/4/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 1 g01126088
1. Turn the crankshaft until the connecting rod caps are at the bottom center.
2. Place a identification mark on the connecting rod and connecting rod cap (2). The number
should match the cylinder number.
3. Remove bolts (1) and connecting rod cap (2).
2/3
329D L & 329D LN Excavators EBM00001-UP (MACHINE) POWERED BY C7 En...
2020/4/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 2 g01126089
4. Remove the lower half of connecting rod bearing (4) from connecting rod cap (2).
5. Push the piston and the connecting rod away from the crankshaft. Remove the upper half of
connecting rod bearing (4) from connecting rod (3).
6. Remove the piston and connecting rod (3) from the cylinder block.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Apr 21 15:57:21 UTC+0800 2020
3/3
329D L & 329D LN Excavators EBM00001-UP (MACHINE) POWERED BY C7 En...
2020/4/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 329D LN EXCAVATOR EBM
Configuration: 329D L & 329D LN Excavators EBM00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02232839
Pistons and Connecting Rods - Disassemble
SMCS - 1225-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 4C-3601 Piston Ring Expander 1
B 1P-1861 Retaining Ring Pliers 1
Start By:
a. Remove the pistons and the connecting rods. Refer to Disassembly and Assembly, "Pistons
and Connecting Rods - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
329D L & 329D LN Excavators EBM00001-UP (MACHINE) POWERED BY C7 En...
2020/4/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 1 g01126141
1. Use Tooling (B) to remove retaining ring (2).
2. Remove piston pin (5) and separate piston (1) from connecting rod (3).
3. Use Tooling (A) to remove piston rings (4).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Apr 21 15:58:18 UTC+0800 2020
2/2
329D L & 329D LN Excavators EBM00001-UP (MACHINE) POWERED BY C7 En...
2020/4/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 329D LN EXCAVATOR EBM
Configuration: 329D L & 329D LN Excavators EBM00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02233056
Pistons and Connecting Rods - Assemble
SMCS - 1225-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 4C-3601 Piston Ring Expander 1
B 1P-1861 Retaining Ring Pliers 1
C
5P-8639 Hydraulic Press (CONNECTING ROD BEARING) 1
8F-0024 Hose As 1
1P-2375 Quick Connect Coupler 1
1P-2376 Quick Connect Coupler 1
4C-9751 Spacer 1
4C-9749 Bushing Adapter 1
4C-9750 Bushing Adapter 1
9U-6600 Hand Hydraulic Pump 1
Note: Prior to removal from the engine, the pistons and connecting rod assemblies were marked.
The components must be reassembled together. The components must be installed in the original
location in the engine. Do not interchange any of the components.
NOTICE
1/4
329D L & 329D LN Excavators EBM00001-UP (MACHINE) POWERED BY C7 En...
2020/4/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01126305
2/4
329D L & 329D LN Excavators EBM00001-UP (MACHINE) POWERED BY C7 En...
2020/4/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 2 g01126306
1. Use Tooling (C) to remove the old bearing and install the new bearing (6) at the same time.
The adapter of Tooling (C) should make full contact with the surfaces of connecting rod (3).
Note: Orient the bearing joint within 12 ± 5 degrees of either Location (X).
NOTICE
The connecting rod must be heated for the installation of the piston pin
bearing. Do not use a torch.
a. Raise the temperature of connecting rod (3) along Length (Y).
(Y) Maximum Length for heating the connecting rod ... 75 ± 5 mm (3.0 ± 0.2 inch)
b. Allow the connecting rod and the bearing to cool to room temperature.
Illustration 3 g01126141
2. Use the following procedure to install piston rings (4).
a. Position the spring for the oil control ring in the oil ring groove in the piston body
assembly.
b. Position the oil control ring over the spring. Position the oil control ring so that the
gap is 180 degrees from the joint in the spring. Use Tooling (A) to install the oil
control ring on the piston.
c. Use Tooling (A) to install the intermediate piston ring with the side that has the
identification “UP-2” toward the top of the piston.
3/4
329D L & 329D LN Excavators EBM00001-UP (MACHINE) POWERED BY C7 En...
2020/4/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. d. Use Tooling (A) to install the top piston ring with the side that has the identification
“UP-1” toward the top of the piston.
e. Position piston rings (4) so the gaps are 120 degrees from each other.
3. Check the clearance between the ends of piston rings (4). Refer to Specifications, "Piston
And Rings".
4. Position piston (1) on connecting rod (3). Apply clean engine oil to piston pin (5) and install
the piston pin. Use Tooling (B) to install retaining ring (2). Make sure that the retaining
rings are fully seated in the grooves of the piston assembly.
End By:
a. Install the pistons and the connecting rods. Refer to Disassembly and Assembly, "Pistons
and Connecting Rods - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Apr 21 15:59:15 UTC+0800 2020
4/4
329D L & 329D LN Excavators EBM00001-UP (MACHINE) POWERED BY C7 En...
2020/4/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 329D LN EXCAVATOR EBM
Configuration: 329D L & 329D LN Excavators EBM00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i04805646
Pistons and Connecting Rods - Install
SMCS - 1225-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 173-5529 Piston Ring Compressor 1
B 4C-5593 Anti-Seize Compound 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Apply clean engine oil to the pistons, the piston rings, and the cylinder bore.
1/4
329D L & 329D LN Excavators EBM00001-UP (MACHINE) POWERED BY C7 En...
2020/4/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 1 g00954373
2. Position the piston rings so that the end gaps are located 120 degrees from each other.
Install Tooling (A) in order to compress the piston rings.
Note: Install the piston and connecting rod so that the forging number on the connecting rod
points toward the flywheel end of the engine.
3. With the number one crankshaft throw at the bottom center, install the piston and
connecting rod in the engine. Ensure that the proper piston and connecting rod are in the
corresponding cylinder with the bearing retainer notch toward the right side of the engine.
4. Line up the piston and the connecting rod with the crankshaft. Use a soft faced hammer and
tap the piston into the cylinder bore until Tooling (A) comes off the piston.
2/4
329D L & 329D LN Excavators EBM00001-UP (MACHINE) POWERED BY C7 En...
2020/4/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 2 g01126089
Illustration 3 g01126088
5. Before connecting rod (3) comes in contact with the crankshaft, install the upper half of
connecting rod bearing (4) . Ensure that the bearing tab engages with the slot in connecting
rod (3) .
6. Apply clean engine oil to the surface of the upper half of connecting rod bearing (4) . Use a
soft faced hammer in order to tap the piston into the cylinder bore while you guide
connecting rod (3) onto the crankshaft.
7. Place the lower half of connecting rod bearing (4) in corresponding connecting rod cap (2) .
Ensure that the bearing tab engages with the groove in connecting rod cap (2) .
8. Apply clean engine oil to the surface of the lower half of connecting rod bearing (4) . Install
connecting rod bearing cap (2) on connecting rod (3) . Ensure that the number on
connecting rod cap (2) matches the number on connecting rod (3) . Ensure that the numbers
are on the same side.
9. Lubricate the new connecting rod bolts with Tooling (B) .
10. Install new bolts (1) . Tighten bolts (1) to a torque of 70 ± 5 N·m (52 ± 4 lb ft).
Note: Refer to Truck Engine News, SEBD6775, "New Fractured Connecting Rod Has Been
Released " for the proper torque procedure on Reman Connecting Rods.
3/4
329D L & 329D LN Excavators EBM00001-UP (MACHINE) POWERED BY C7 En...
2020/4/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. 11. Place an index mark on each bolt. Tighten each bolt (1) for an additional 120 ± 5 degrees
(1/3 turn).
End By:
a. Install the piston cooling jets. Refer to the Disassembly and Assembly Manual, "Piston
Cooling Jets - Remove and Install".
b. Install the engine oil pump. Refer to the Disassembly and Assembly Manual, "Engine Oil
Pump - Install".
c. Install the cylinder head. Refer to the Disassembly and Assembly Manual, "Cylinder Head -
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Apr 21 16:00:11 UTC+0800 2020
4/4
329D L & 329D LN Excavators EBM00001-UP (MACHINE) POWERED BY C7 En...
2020/4/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 329D LN EXCAVATOR EBM
Configuration: 329D L & 329D LN Excavators EBM00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02233237
Connecting Rod Bearings - Remove
SMCS - 1219-011
Removal Procedure
Start By:
A. Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
329D L & 329D LN Excavators EBM00001-UP (MACHINE) POWERED BY C7 En...
2020/4/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 1 g01126410
1. Turn the crankshaft until the connecting rod bearing caps are accessible.
2. Place an identification mark on connecting rod (3) and connecting rod bearing cap (2). The
number should match the cylinder number.
3. Remove bolts (1) and connecting rod bearing cap (2) from connecting rod (3). Remove the
lower half of connecting rod bearing (4) from connecting rod bearing cap (2) .
4. Push the connecting rod away from the crankshaft. Remove the upper half of connecting rod
bearing (4) from connecting rod (3) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Apr 21 16:01:08 UTC+0800 2020
2/2
329D L & 329D LN Excavators EBM00001-UP (MACHINE) POWERED BY C7 En...
2020/4/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 329D LN EXCAVATOR EBM
Configuration: 329D L & 329D LN Excavators EBM00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i03744497
Connecting Rod Bearings - Install
SMCS - 1219-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 4C-5593 Anti-Seize Compound -
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
329D L & 329D LN Excavators EBM00001-UP (MACHINE) POWERED BY C7 En...
2020/4/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 1 g01126410
Note: Install the connecting rod bearings dry when clearance checks are performed. Refer to
Disassembly and Assembly, "Bearing Clearance - Check". Apply clean engine oil on the
connecting rod bearings for final assembly.
1. Install a new lower half of connecting rod bearing (4) in connecting rod bearing cap (2) .
2. Install a new upper half of connecting rod bearing (4) in connecting rod (3) .
3. Pull connecting rod (3) onto the crankshaft.
4. Lubricate the new connecting rod bolts with Tooling (A) .
5. Install connecting rod bearing cap (2) and bolts (1) . Ensure that the number on the side of
connecting rod bearing cap (2) is on the same side as the number on connecting rod (3) .
6. Tighten bolts (1) to a torque of 70 ± 5 N·m (52 ± 4 lb ft).
7. Place an index mark on each bolt. Tighten each bolt (1) for an additional 120 ± 5 degrees
(1/3 turn).
End By: Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump -
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Apr 21 16:02:05 UTC+0800 2020
2/2
329D L & 329D LN Excavators EBM00001-UP (MACHINE) POWERED BY C7 En...
2020/4/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 329D LN EXCAVATOR EBM
Configuration: 329D L & 329D LN Excavators EBM00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02304516
Crankshaft Main Bearings - Remove
SMCS - 1203-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 2P-5518 Main Bearing Tool 1
Start By:
a. Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
329D L & 329D LN Excavators EBM00001-UP (MACHINE) POWERED BY C7 En...
2020/4/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 1 g00988316
1. Remove bolts (1) that hold crankshaft main bearing cap (2). Remove crankshaft main
bearing cap (2).
2. Remove the lower half of the crankshaft main bearing from crankshaft main bearing cap (2).
2/4
329D L & 329D LN Excavators EBM00001-UP (MACHINE) POWERED BY C7 En...
2020/4/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Illustration 2 g00988318
NOTICE
If the crankshaft is turned in the wrong direction, the tab of the
crankshaft main bearing will be pushed between the crankshaft and
the cylinder block. this can cause damage to either or both the
crankshaft and the cylinder block.
3. Use the following steps in order to remove the upper half of crankshaft main bearings:
a. Turn the crankshaft until Tooling (A) can be installed in the crankshaft journal. Install
Tooling (A).
b. Turn the crankshaft in order to remove the upper half of the crankshaft main bearing.
Tooling (A) must first contact the crankshaft main bearing opposite the tab end of the
crankshaft main bearing. In order to get the tab out first, the crankshaft must be turned
in the correct direction.
c. Check the condition of the crankshaft main bearings. Refer to the Guideline For
Reusable Parts, SEBF8009, "Main and Connecting Rod Bearings" or refer to the
Guideline For Reusable Parts, SEBV0544, "Engine Bearings and Crankshafts".
3/4
329D L & 329D LN Excavators EBM00001-UP (MACHINE) POWERED BY C7 En...
2020/4/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...