This document provides instructions for removing and installing engine components on a Caterpillar 329D L & 329D LN Excavator, including:
- Removing and installing inlet and exhaust valves
- Removing and installing inlet and exhaust valve guides
- Removing and installing inlet and exhaust valve seat inserts
- Removing the engine oil filter base and oil cooler
- Disassembling the engine oil filter base
The document contains detailed step-by-step instructions and illustrations for each procedure. Safety notices are provided throughout to warn technicians of potential injury risks.
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a Caterpillar C7 engine. It describes:
1) Using various tools to compress springs and remove components like retainers, springs, and valves.
2) Cleaning parts and lubricating valves before installation.
3) Tapping guides into place using drivers and ensuring proper protrusion heights.
4) Extracting old seat inserts and pressing in new ones at a lowered temperature.
Caterpillar Cat 329DLN Excavator (Prefix SCY) Service Repair Manual (SCY00001...f8usiedkdmm
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a Caterpillar C7 engine. It describes:
1) Using various tools to compress springs and remove components like valves, guides, and seats in a specific order.
2) Cleaning all parts to prevent damage and installing new components like valves, guides, and seats in the reverse order of removal using press tools.
3) Notes that proper assembly prevents injury and contaminants cause premature wear.
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a Caterpillar C7 engine. It describes:
1) Using various tools to compress springs and remove components like retainers, springs, and valves.
2) Cleaning parts and lubricating valves before installation.
3) Tapping guides into place using drivers and ensuring proper heights above the cylinder head.
4) Extracting old seat inserts and pressing new ones in at the proper depths.
Caterpillar Cat 329DLN Excavator (Prefix SCY) Service Repair Manual (SCY00001...paws21610697
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a Caterpillar C7 engine. It describes:
1) Using various tools to compress springs and remove components like retainers, springs, and valves.
2) Cleaning and lubricating parts before installing in reverse order.
3) Precautions to take like ensuring parts are clean and wearing protective equipment when working with springs.
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a Caterpillar C7 engine. It describes:
1) Using various tools to compress springs and remove components like retainers, springs, and valves.
2) Cleaning and lubricating parts before installing in reverse order.
3) Precautions to take like ensuring parts are clean and wearing protective equipment when working with springs.
Caterpillar Cat 329DLN Excavator (Prefix SCY) Service Repair Manual (SCY00001...f7djidksmd3e
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a Caterpillar C7 engine. It describes:
1) Using various tools to compress springs and remove components like valves, guides, and seats in a specific order.
2) Cleaning all parts to prevent damage and installing new components like seats with presses.
3) Lubricating and placing components in the proper order before using tools to fully seat them.
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a Caterpillar C7 engine. It describes:
1) Using various tools to compress springs and remove components like retainers, springs, and valves.
2) Cleaning parts and lubricating valves before installation.
3) Tapping guides into place using drivers and ensuring proper protrusion heights.
4) Extracting old seat inserts and pressing in new ones at a lowered temperature.
Caterpillar Cat 329DLN Excavator (Prefix SCY) Service Repair Manual (SCY00001...uddksemd8ud
This document provides instructions for removing the engine oil filter base and oil cooler from a Caterpillar 329D LN excavator. The key steps are:
1. Drain engine oil and coolant from the systems before removal to contain fluids.
2. For a remote-mounted filter base, use a strap wrench to remove the oil filter, then remove bolts and the filter base.
3. For an engine-mounted base, drain the cooling system, then remove hoses and bolts to separate the oil cooler from the engine.
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a Caterpillar C7 engine. It describes:
1) Using various tools to compress springs and remove components like retainers, springs, and valves.
2) Cleaning parts and lubricating valves before installation.
3) Tapping guides into place using drivers and ensuring proper protrusion heights.
4) Extracting old seat inserts and pressing in new ones at a lowered temperature.
Caterpillar Cat 329DLN Excavator (Prefix SCY) Service Repair Manual (SCY00001...f8usiedkdmm
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a Caterpillar C7 engine. It describes:
1) Using various tools to compress springs and remove components like valves, guides, and seats in a specific order.
2) Cleaning all parts to prevent damage and installing new components like valves, guides, and seats in the reverse order of removal using press tools.
3) Notes that proper assembly prevents injury and contaminants cause premature wear.
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a Caterpillar C7 engine. It describes:
1) Using various tools to compress springs and remove components like retainers, springs, and valves.
2) Cleaning parts and lubricating valves before installation.
3) Tapping guides into place using drivers and ensuring proper heights above the cylinder head.
4) Extracting old seat inserts and pressing new ones in at the proper depths.
Caterpillar Cat 329DLN Excavator (Prefix SCY) Service Repair Manual (SCY00001...paws21610697
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a Caterpillar C7 engine. It describes:
1) Using various tools to compress springs and remove components like retainers, springs, and valves.
2) Cleaning and lubricating parts before installing in reverse order.
3) Precautions to take like ensuring parts are clean and wearing protective equipment when working with springs.
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a Caterpillar C7 engine. It describes:
1) Using various tools to compress springs and remove components like retainers, springs, and valves.
2) Cleaning and lubricating parts before installing in reverse order.
3) Precautions to take like ensuring parts are clean and wearing protective equipment when working with springs.
Caterpillar Cat 329DLN Excavator (Prefix SCY) Service Repair Manual (SCY00001...f7djidksmd3e
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a Caterpillar C7 engine. It describes:
1) Using various tools to compress springs and remove components like valves, guides, and seats in a specific order.
2) Cleaning all parts to prevent damage and installing new components like seats with presses.
3) Lubricating and placing components in the proper order before using tools to fully seat them.
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a Caterpillar C7 engine. It describes:
1) Using various tools to compress springs and remove components like retainers, springs, and valves.
2) Cleaning parts and lubricating valves before installation.
3) Tapping guides into place using drivers and ensuring proper protrusion heights.
4) Extracting old seat inserts and pressing in new ones at a lowered temperature.
Caterpillar Cat 329DLN Excavator (Prefix SCY) Service Repair Manual (SCY00001...uddksemd8ud
This document provides instructions for removing the engine oil filter base and oil cooler from a Caterpillar 329D LN excavator. The key steps are:
1. Drain engine oil and coolant from the systems before removal to contain fluids.
2. For a remote-mounted filter base, use a strap wrench to remove the oil filter, then remove bolts and the filter base.
3. For an engine-mounted base, drain the cooling system, then remove hoses and bolts to separate the oil cooler from the engine.
This document provides instructions for removing the engine oil filter base and oil cooler from a Caterpillar 329D LN excavator. The key steps are:
1. Drain engine oil and coolant from the systems before removal to contain fluids.
2. For a remote-mounted filter base, use a strap wrench to remove the oil filter, then remove bolts and the filter base.
3. For an engine-mounted base, drain the cooling system, then remove hoses and bolts to separate the oil cooler from the engine.
Caterpillar Cat 329DLN Excavator (Prefix SCY) Service Repair Manual (SCY00001...jdjkskmikdkmd
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a Caterpillar C7 engine. It describes:
1) Using various tools to compress springs and remove components like valves, guides, and seats in a specific order.
2) Cleaning all parts to prevent damage and installing new components like valves, guides, and seats in the reverse order of removal using press tools.
3) The document contains warnings about safety and preventing injury when working with springs under pressure.
This document provides instructions for removing the engine oil filter base and oil cooler from a Caterpillar 329D LN excavator. The key steps are:
1. Drain engine oil and coolant from the systems before removal to contain fluids.
2. For a remote-mounted filter base, use a strap wrench to remove the oil filter, then remove bolts and the filter base.
3. For an engine-mounted base, drain the cooling system, then remove hoses and bolts to separate the oil cooler from the engine.
This document provides instructions for removing the engine oil filter base and oil cooler from a Caterpillar 329D LN excavator. The key steps are:
1. Drain engine oil and coolant from the systems before removal to contain fluids.
2. For a remote-mounted filter base, use a strap wrench to remove the oil filter, then remove bolts and the filter base.
3. For an engine-mounted base, drain the cooling system, then remove hoses and bolts to separate the oil cooler from the engine.
This document provides instructions for removing the engine oil filter base and oil cooler from a Caterpillar 329D LN excavator. The key steps are:
1. Drain engine oil and coolant from the systems before removal to contain fluids.
2. For a remote-mounted filter base, use a strap wrench to remove the oil filter, then remove bolts and the filter base.
3. For an engine-mounted base, drain the cooling system, then remove hoses and bolts to separate the oil cooler from the engine.
This document provides instructions for removing the engine oil filter base and oil cooler from a Caterpillar 329D LN excavator. The key steps are:
1. Drain engine oil and coolant from the systems before removal to contain fluids.
2. For a remote-mounted filter base, use a strap wrench to remove the oil filter, then remove bolts and the filter base.
3. For an engine-mounted base, drain the cooling system, then remove hoses and bolts to separate the oil cooler from the engine.
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a Caterpillar C7 engine. It describes:
1) Using various tools to compress springs and remove components like retainers, springs, and valves.
2) Cleaning parts and lubricating valves before installation.
3) Tapping guides into place using drivers and ensuring proper protrusion heights.
4) Extracting old seat inserts and pressing new ones in at a lowered temperature.
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a Caterpillar C7 engine. It describes:
1) Using various tools to compress springs and remove components like retainers, springs, and valves.
2) Cleaning and lubricating parts before installing valves, guides, and seats in the proper order and orientation.
3) Precautions to take like ensuring parts are clean and wearing protective equipment when working with spring-loaded components.
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a Caterpillar C7 engine. It describes:
1) Using various tools to compress springs and remove components like valves, guides, and seats in a specific order.
2) Cleaning all parts to prevent damage and installing new components like seats with presses.
3) Lubricating and placing components in the proper order before using tools to fully seat them.
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a Caterpillar C7 engine. It describes:
1) Using various tools to compress springs and remove components like retainers, springs, and valves.
2) Cleaning and lubricating parts before installing valves, guides, and seats in the proper order and orientation.
3) Precautions to take like ensuring parts are clean and wearing protective equipment when working with spring-loaded components.
The document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator, including:
1. Removing and installing the front cover, which involves removing bolts and installing a new gasket.
2. Removing the front housing, which requires supporting the engine, removing bolts, and removing the housing.
3. Installing the front housing, which involves cleaning, applying primer and sealant, positioning the housing, and installing bolts.
This document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator. It includes procedures for removing and installing the front cover, front housing, camshaft idler gear, valve mechanism cover, valve mechanism cover base, rocker shaft and pushrods. The document provides illustrations and specifies required tools for each procedure. Safety notices are included to keep parts clean and contain fluids.
The document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator, including:
1. Removing and installing the front cover, which involves removing bolts and installing a new gasket.
2. Removing the front housing, which requires supporting the engine, removing bolts, and removing the housing.
3. Installing the front housing, which involves cleaning, applying primer and sealant, positioning the housing, and installing bolts.
This document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator. It includes procedures for removing and installing the front cover, front housing, camshaft idler gear, valve mechanism cover, valve mechanism cover base, rocker shaft and pushrods. The document provides illustrations and specifies required tools for each procedure. Safety notices are included to keep parts clean and contain fluids.
This document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator. It includes procedures for removing and installing the front cover, front housing, camshaft idler gear, valve mechanism cover, valve mechanism cover base, rocker shaft and pushrods. The document provides illustrations and specifies any required tools for each procedure. Technicians are instructed to keep all parts clean and free of contaminants to prevent premature wear during reassembly.
This document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator. It includes procedures for removing and installing the front cover, front housing, camshaft idler gear, valve mechanism cover, valve mechanism cover base, rocker shaft and pushrods. The document provides illustrations and specifies required tools for each procedure. Safety notices are included to keep parts clean and contain fluids.
The document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator, including:
1. Removing and installing the front cover, which involves removing bolts and installing a new gasket.
2. Removing the front housing, which requires supporting the engine, removing bolts, and removing the housing.
3. Installing the front housing, which involves cleaning, applying primer and sealant, positioning the housing, and installing bolts.
This document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator. It includes procedures for removing and installing the front cover, front housing, camshaft idler gear, valve mechanism cover, valve mechanism cover base, rocker shaft and pushrods. The document provides illustrations and specifies required tools for each procedure. Safety notices are included to keep parts clean and contain fluids.
Caterpillar cat 324 d ln excavator (prefix kjr) service repair manual (kjr000...ifoseidkkd
The document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator, including:
1. Removing and installing the front cover, which involves removing bolts and installing a new gasket.
2. Removing the front housing, which requires supporting the engine, removing bolts, and removing the housing.
3. Installing the front housing, which involves cleaning, applying primer and sealant, positioning the housing, and installing bolts.
The document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator, including:
1. Removing and installing the front cover, which involves removing bolts and installing a new gasket.
2. Removing the front housing, which requires supporting the engine, removing bolts, and removing the housing.
3. Installing the front housing, which involves cleaning, applying primer and sealant, positioning the housing, and installing bolts.
Caterpillar Cat 336F L Excavator (Prefix KCS) Service Repair Manual (KCS00001...cnp692569
The document provides instructions for removing and installing various components of a Caterpillar C9.3 engine, including the combustion head, ARD nozzle heater relay, ARD fuel solenoid valve, exhaust manifold, and exhaust elbow. The procedures include removing fasteners and connectors, loosening clamps, and installing replacement parts in the reverse order of removal while applying sealants and lubricants and torquing fasteners to the specified values. Safety precautions are provided regarding working on hot engine components and with flammable liquids.
1. The document provides step-by-step instructions for disassembling the travel motor of a 336F excavator.
2. It describes removing 27 components and parts from the travel motor in a specific sequence using various tools.
3. Special care must be taken when removing springs and components under pressure to avoid injury from released forces.
More Related Content
Similar to Caterpillar Cat 329DLN Excavator (Prefix SCY) Service Repair Manual (SCY00001 and up).pdf
This document provides instructions for removing the engine oil filter base and oil cooler from a Caterpillar 329D LN excavator. The key steps are:
1. Drain engine oil and coolant from the systems before removal to contain fluids.
2. For a remote-mounted filter base, use a strap wrench to remove the oil filter, then remove bolts and the filter base.
3. For an engine-mounted base, drain the cooling system, then remove hoses and bolts to separate the oil cooler from the engine.
Caterpillar Cat 329DLN Excavator (Prefix SCY) Service Repair Manual (SCY00001...jdjkskmikdkmd
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a Caterpillar C7 engine. It describes:
1) Using various tools to compress springs and remove components like valves, guides, and seats in a specific order.
2) Cleaning all parts to prevent damage and installing new components like valves, guides, and seats in the reverse order of removal using press tools.
3) The document contains warnings about safety and preventing injury when working with springs under pressure.
This document provides instructions for removing the engine oil filter base and oil cooler from a Caterpillar 329D LN excavator. The key steps are:
1. Drain engine oil and coolant from the systems before removal to contain fluids.
2. For a remote-mounted filter base, use a strap wrench to remove the oil filter, then remove bolts and the filter base.
3. For an engine-mounted base, drain the cooling system, then remove hoses and bolts to separate the oil cooler from the engine.
This document provides instructions for removing the engine oil filter base and oil cooler from a Caterpillar 329D LN excavator. The key steps are:
1. Drain engine oil and coolant from the systems before removal to contain fluids.
2. For a remote-mounted filter base, use a strap wrench to remove the oil filter, then remove bolts and the filter base.
3. For an engine-mounted base, drain the cooling system, then remove hoses and bolts to separate the oil cooler from the engine.
This document provides instructions for removing the engine oil filter base and oil cooler from a Caterpillar 329D LN excavator. The key steps are:
1. Drain engine oil and coolant from the systems before removal to contain fluids.
2. For a remote-mounted filter base, use a strap wrench to remove the oil filter, then remove bolts and the filter base.
3. For an engine-mounted base, drain the cooling system, then remove hoses and bolts to separate the oil cooler from the engine.
This document provides instructions for removing the engine oil filter base and oil cooler from a Caterpillar 329D LN excavator. The key steps are:
1. Drain engine oil and coolant from the systems before removal to contain fluids.
2. For a remote-mounted filter base, use a strap wrench to remove the oil filter, then remove bolts and the filter base.
3. For an engine-mounted base, drain the cooling system, then remove hoses and bolts to separate the oil cooler from the engine.
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a Caterpillar C7 engine. It describes:
1) Using various tools to compress springs and remove components like retainers, springs, and valves.
2) Cleaning parts and lubricating valves before installation.
3) Tapping guides into place using drivers and ensuring proper protrusion heights.
4) Extracting old seat inserts and pressing new ones in at a lowered temperature.
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a Caterpillar C7 engine. It describes:
1) Using various tools to compress springs and remove components like retainers, springs, and valves.
2) Cleaning and lubricating parts before installing valves, guides, and seats in the proper order and orientation.
3) Precautions to take like ensuring parts are clean and wearing protective equipment when working with spring-loaded components.
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a Caterpillar C7 engine. It describes:
1) Using various tools to compress springs and remove components like valves, guides, and seats in a specific order.
2) Cleaning all parts to prevent damage and installing new components like seats with presses.
3) Lubricating and placing components in the proper order before using tools to fully seat them.
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a Caterpillar C7 engine. It describes:
1) Using various tools to compress springs and remove components like retainers, springs, and valves.
2) Cleaning and lubricating parts before installing valves, guides, and seats in the proper order and orientation.
3) Precautions to take like ensuring parts are clean and wearing protective equipment when working with spring-loaded components.
The document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator, including:
1. Removing and installing the front cover, which involves removing bolts and installing a new gasket.
2. Removing the front housing, which requires supporting the engine, removing bolts, and removing the housing.
3. Installing the front housing, which involves cleaning, applying primer and sealant, positioning the housing, and installing bolts.
This document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator. It includes procedures for removing and installing the front cover, front housing, camshaft idler gear, valve mechanism cover, valve mechanism cover base, rocker shaft and pushrods. The document provides illustrations and specifies required tools for each procedure. Safety notices are included to keep parts clean and contain fluids.
The document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator, including:
1. Removing and installing the front cover, which involves removing bolts and installing a new gasket.
2. Removing the front housing, which requires supporting the engine, removing bolts, and removing the housing.
3. Installing the front housing, which involves cleaning, applying primer and sealant, positioning the housing, and installing bolts.
This document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator. It includes procedures for removing and installing the front cover, front housing, camshaft idler gear, valve mechanism cover, valve mechanism cover base, rocker shaft and pushrods. The document provides illustrations and specifies required tools for each procedure. Safety notices are included to keep parts clean and contain fluids.
This document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator. It includes procedures for removing and installing the front cover, front housing, camshaft idler gear, valve mechanism cover, valve mechanism cover base, rocker shaft and pushrods. The document provides illustrations and specifies any required tools for each procedure. Technicians are instructed to keep all parts clean and free of contaminants to prevent premature wear during reassembly.
This document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator. It includes procedures for removing and installing the front cover, front housing, camshaft idler gear, valve mechanism cover, valve mechanism cover base, rocker shaft and pushrods. The document provides illustrations and specifies required tools for each procedure. Safety notices are included to keep parts clean and contain fluids.
The document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator, including:
1. Removing and installing the front cover, which involves removing bolts and installing a new gasket.
2. Removing the front housing, which requires supporting the engine, removing bolts, and removing the housing.
3. Installing the front housing, which involves cleaning, applying primer and sealant, positioning the housing, and installing bolts.
This document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator. It includes procedures for removing and installing the front cover, front housing, camshaft idler gear, valve mechanism cover, valve mechanism cover base, rocker shaft and pushrods. The document provides illustrations and specifies required tools for each procedure. Safety notices are included to keep parts clean and contain fluids.
Caterpillar cat 324 d ln excavator (prefix kjr) service repair manual (kjr000...ifoseidkkd
The document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator, including:
1. Removing and installing the front cover, which involves removing bolts and installing a new gasket.
2. Removing the front housing, which requires supporting the engine, removing bolts, and removing the housing.
3. Installing the front housing, which involves cleaning, applying primer and sealant, positioning the housing, and installing bolts.
The document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator, including:
1. Removing and installing the front cover, which involves removing bolts and installing a new gasket.
2. Removing the front housing, which requires supporting the engine, removing bolts, and removing the housing.
3. Installing the front housing, which involves cleaning, applying primer and sealant, positioning the housing, and installing bolts.
Similar to Caterpillar Cat 329DLN Excavator (Prefix SCY) Service Repair Manual (SCY00001 and up).pdf (20)
Caterpillar Cat 336F L Excavator (Prefix KCS) Service Repair Manual (KCS00001...cnp692569
The document provides instructions for removing and installing various components of a Caterpillar C9.3 engine, including the combustion head, ARD nozzle heater relay, ARD fuel solenoid valve, exhaust manifold, and exhaust elbow. The procedures include removing fasteners and connectors, loosening clamps, and installing replacement parts in the reverse order of removal while applying sealants and lubricants and torquing fasteners to the specified values. Safety precautions are provided regarding working on hot engine components and with flammable liquids.
1. The document provides step-by-step instructions for disassembling the travel motor of a 336F excavator.
2. It describes removing 27 components and parts from the travel motor in a specific sequence using various tools.
3. Special care must be taken when removing springs and components under pressure to avoid injury from released forces.
This document provides instructions for disassembling and assembling the travel motor of a 336F excavator. The disassembly process involves 30 steps to remove all components of the travel motor. The assembly process reverses the disassembly with 27 steps and requires various tools to reinstall components in the proper order and orientation. Precautions are outlined to prevent injury from spring forces.
The document provides instructions for removing and installing various components of a Caterpillar C9.3 engine, including the combustion head, ARD nozzle heater relay, ARD fuel solenoid valve, exhaust manifold, and exhaust elbow. The procedures include removing parts in the specified order, cleaning components, installing new gaskets and O-rings, and torquing fasteners to the specified values. Safety precautions are provided regarding working on hot engine components and with flammable liquids.
This document provides instructions for disassembling the travel motor on 336F and 336F L Excavator models. It outlines 27 steps to fully disassemble the travel motor, including removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals, and other internal parts. Precautions are provided to safely release stored energy from springs. Detailed illustrations accompany each step to ensure correct disassembly. Required tools are listed.
Caterpillar Cat 336E L HVG Excavator (Prefix RBS) Service Repair Manual (RBS0...cnp692569
The document provides instructions for installing and removing components related to the rear power take-off (RPTO) system on a Caterpillar C9.3 engine. The removal procedure includes removing the crankshaft rear seal, various bolts and gears, thrust washers, dowels, bearings, seals and the PTO shaft. The installation procedure specifies cleaning and lubricating parts before reinstalling components in reverse order, applying thread lock to bolts and torquing to specification.
Caterpillar Cat 336E L Excavator (Prefix YEP) Service Repair Manual (YEP00001...cnp692569
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing seals, bearings, springs and other components from the motor housing. The assembly process details installing these components in reverse order and applying lubricant or threadlock where specified. Proper torque values are listed for fasteners. The instructions note to mark components' orientations before removal to aid reinstallation.
Caterpillar Cat 336E L Excavator (Prefix KED) Service Repair Manual (KED00001...cnp692569
1. The document provides assembly instructions for a travel motor on an excavator. It details 28 steps to assemble the travel motor, including installing seals, springs, pistons, and other components.
2. Removal and installation instructions are provided for the final drive and travel motor assembly. 10 steps are outlined for removal, including draining oil, removing hoses and fittings, and using lifting tools. 13 steps are given for installation, with torque specifications for the reinstallation bolts.
3. Disassembly instructions for the final drive include removing the cover, plate, and links using lifting brackets and forcing bolts.
Caterpillar Cat 336E L Excavator (Prefix GTJ) Service Repair Manual (GTJ00001...cnp692569
The document provides instructions for disassembling and assembling a travel motor. It details 28 steps for travel motor assembly, including installing seals, springs, pistons and other components. Removal of the final drive and travel motor requires draining fluids, removing bolts and hoses, and lifting out the assembly. Reinstallation requires cleaning, applying sealant to bolts, and torquing bolts to the specified values.
The document provides instructions for installing and removing components related to the rear power take-off (RPTO) system on a Caterpillar C9.3 engine. The removal procedure includes removing the crankshaft rear seal, various bolts and gears, thrust washers, dowels, bearings, seals and the PTO shaft. The installation procedure specifies cleaning and lubricating parts before reinstalling components in reverse order, applying thread locking compound to bolts, and torquing bolts to the specified values.
This document provides instructions for disassembling and assembling the travel motor of a 336E excavator. It outlines 27 steps for disassembly, removing components like the head, springs, plates, seals and bearings. It then outlines 17 steps for assembly, replacing these components in reverse order and noting specifics like lubrication, torque settings and alignment marks. Tools required are listed.
1. The document provides assembly instructions for a travel motor on an excavator. It details 28 steps to assemble the travel motor, including installing seals, springs, pistons, and other components.
2. Removal and installation instructions are provided for the final drive and travel motor assembly of an excavator. The procedure includes disconnecting hoses, removing mounting bolts, and lifting out the assembly.
3. Disassembly instructions are given for a final drive, including removing the cover, plate, and installing lifting brackets to remove internal components. Detailed diagrams accompany each step.
The document provides instructions for disassembling and assembling a travel motor. It details 28 steps for disassembling the travel motor, removing components like seals, springs, and plates. It then lists 13 steps for reassembling the travel motor and tightening components like bolts, hoses, and covers to the specified torques.
Caterpillar Cat 336D2 L Excavator (Prefix ZCT) Service Repair Manual (ZCT0000...cnp692569
This document provides disassembly and assembly instructions for the main hydraulic pump on a 336D2 L excavator. It lists over 50 steps to fully disassemble the pump by removing covers, valves, springs, seals, gears, and other components. The corresponding assembly section lists the steps to reinstall all components in reverse order, noting requirements for special tools and heating/pressing some bearings and seals back into place. Precautions are included for releasing spring forces to avoid injury.
Caterpillar Cat 336D2 L Excavator (Prefix YCF) Service Repair Manual (YCF0000...cnp692569
The document provides instructions for disassembling and assembling a piston pump (hydraulic fan) for Caterpillar 336D2 and 336D2 L excavators. The disassembly procedure involves removing 30 parts in 8 steps, taking precautions for spring-loaded parts. The assembly procedure reinstalls the parts in 30 steps, heating and cooling certain parts, using tools to install retaining rings and measure end play, and filling the hydraulic system.
Caterpillar Cat 336D2 L Excavator (Prefix XBH) Service Repair Manual (XBH0000...cnp692569
This document provides instructions for installing and removing the final drive and travel motor, and disassembling and assembling the swivel, on Caterpillar 336D2 and 336D2 L excavators. The procedures include using various tools to lift heavy components, installing and tightening bolts, replacing O-rings and seals, and checking for leaks during assembly. Cleanliness is emphasized to prevent contamination.
Caterpillar Cat 336D2 L Excavator (Prefix WDC) Service Repair Manual (WDC0000...cnp692569
The document provides instructions for assembling and disassembling components of a piston motor (hydraulic fan) and hydraulic lockout control on excavator models 336D2 and 336D2 L. It describes 17 steps for assembling the piston motor, including installing bearings, seals, springs, and retaining rings. It also describes removing and disassembling the hydraulic lockout control into individual parts and reassembling it. Safety precautions are provided for parts under spring tension.
Caterpillar Cat 336D2 L Excavator (Prefix WBC) Service Repair Manual (WBC0000...cnp692569
The document provides instructions for removing and installing valve guides, valve seat inserts, an engine oil filter base, and oil cooler on a Caterpillar C9 engine. The removal procedures describe using various tools to remove the components from the cylinder head and engine. The installation sections explain cleaning and lubricating parts before reinstalling them using specific tools and following the correct procedure.
Caterpillar Cat 336D2 L Excavator (Prefix TLY) Service Repair Manual (TLY0000...cnp692569
The document provides instructions for disassembling and assembling a piston pump. It includes 30 steps for assembly, beginning with cleaning parts and ending by filling the hydraulic system with oil. The 3 steps for disassembly are: 1) removing bolts and the head, 2) removing internal components like pistons and bearings, and 3) using tools to remove the rotating group and bearing cone. Protective equipment is recommended as parts are under spring pressure.
Caterpillar Cat 336D2 L Excavator (Prefix LAM) Service Repair Manual (LAM0000...cnp692569
This document provides instructions for removing and installing the unit injector hydraulic pump on a Caterpillar C9 engine. The removal process involves disconnecting fuel lines and electrical connections, removing mounting bolts, and taking out the O-ring seal. Installation is the reverse of removal, and includes cleaning parts, applying a new O-ring seal, reinstalling mounting bolts, and reconnecting fuel lines and electrical connections. Proper cleaning and containment of fluids is emphasized. Both non-dual and dual tapered roller bearing pump types are covered.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 329D LN EXCAVATOR SCY
Configuration: 329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02228289
Inlet and Exhaust Valves - Remove and Install
SMCS - 1105-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1
Start By:
a. Remove the cylinder head assembly. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engi...
2020/4/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g01127720
The valve spring keepers can be thrown from the valve when the valve
spring compressor is released. Ensure that the valve spring keepers are
properly installed on the valve stem. To help prevent personal injury,
keep away from the front of the valve spring keepers and valve springs
during the installation of the valves.
Note: The following components of the exhaust valves are different from the components of
the inlet valves: spring retainer (5), valve spring (4) and valve (2).
1. Use Tooling (A) to compress valve spring (4). Remove retainer locks (6).
2. Remove Tooling (A). Remove spring retainer (5), valve spring (4), and washer (3).
3. Remove valve seal (1) and valve (2).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1
NOTICE
2/4
329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engi...
2020/4/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01127720
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
1. Lubricate valve (2) with clean engine oil. Install valve (2) in the cylinder head assembly.
Install new valve seal (1) against the valve guide.
2. Place the following items on the valve stem: washer (3), valve spring (4) and spring retainer
(5).
Note: A small amount of grease can be used to hold the retainer locks in position during
installation.
3. Use Tooling (A) to compress valve spring (4). Install retainer locks (6).
End By:
3/4
329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engi...
2020/4/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. a. Install the cylinder head assembly. Refer to Disassembly and Assembly, "Cylinder Head -
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Apr 23 13:20:05 UTC+0800 2020
4/4
329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engi...
2020/4/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 329D LN EXCAVATOR SCY
Configuration: 329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i06201017
Inlet and Exhaust Valve Guides - Remove and Install
SMCS - 1104-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7793 Valve Guide Driver 1
B 9U-6895 Valve Guide Driver 1
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engi...
2020/4/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 1 g01124395
1. Use Tooling (A) to remove the inlet valve guides from the cylinder head assembly. Use
Tooling (B) to remove the exhaust valve guides from the cylinder head assembly.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1U-7793 Valve Guide Driver 1
B 9U-6895 Valve Guide Driver 1
C 1U-7792 Guide Collar 1
D 149-4008 Guide Collar 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3
329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engi...
2020/4/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 2 g01124397
Note: Position the valve guides and tap on the top of the valve guides in order to start the
valve guides into the cylinder head assembly.
1. Use Tooling (A) and Tooling (C) to install inlet valve guides (1) . Install inlet valve guides
(1) until the protrusion is 23.0 ± 0.50 mm (0.90 ± 0.020 inch) above the cylinder head
assembly.
2. Use Tooling (B) and Tooling (D) to install the exhaust valve guides. Install the exhaust
valve guides until the protrusion is 24.05 ± 0.5 mm (1.0 ± 0.02 inch) above the cylinder
head assembly.
End By: Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Apr 23 13:21:01 UTC+0800 2020
3/3
329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engi...
2020/4/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 329D LN EXCAVATOR SCY
Configuration: 329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02954230
Inlet and Exhaust Valve Seat Inserts - Remove and Install
SMCS - 1103-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1)
6V-4194 Valve Seat Extractor(2)
1
165-5647 Valve Seat Extractor(3)
1
6V-4804 Handle 1
6V-4192 Shaft 1
6V-4199 Lifting Bracket 1
(1)
Part of the 166-7441 Valve Seat Extractor Tool Group
(2)
Use for removal of the exhaust valve seats
(3)
Use for removal of the inlet valve seats
Start By:
a. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engi...
2020/4/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 1 g01124436
1. Use Tooling (A) to remove valve seat inserts (1).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
B
149-6115 Installer 1
133-9306 Valve Guide 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3
329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engi...
2020/4/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 2 g01475612
1. Lower the temperature of new valve seat inserts (1).
2. Use Tooling (B) and a suitable press to install the new valve seat inserts in the cylinder
head.
Note: Do not machine the prefinished valve seat inserts in order to correct the valve stem
projection. An excessive valve stem projection indicates that the valve seat insert is not
seated or material was not cleaned from the bottom of the counterbore.
End By:
a. Install the inlet valves and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Apr 23 13:21:56 UTC+0800 2020
3/3
329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engi...
2020/4/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 329D LN EXCAVATOR SCY
Configuration: 329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02301129
Engine Oil Filter Base and Oil Cooler - Remove
SMCS - 1306-011; 1378-012
Removal Procedure
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Remote Mounted Engine Oil Filter Base
1/3
329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engi...
2020/4/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench As 1
Illustration 1 g01152338
1. Use Tooling (A) to remove engine oil filter (1) .
2. Remove bolts (2) and engine oil filter base (3) .
Engine Mounted Engine Oil Filter Base
1. Drain the coolant from the cooling system into a suitable container for storage or disposal.
Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change".
2/3
329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engi...
2020/4/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 2 g01152340
2. Disconnect hose assemblies (4) .
3. Disconnect hose assembly (5) .
4. Remove bolts (6) and engine oil filter base (7) .
5. Remove oil cooler (8) and the gasket from the engine.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Apr 23 13:22:52 UTC+0800 2020
3/3
329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engi...
2020/4/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 329D LN EXCAVATOR SCY
Configuration: 329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02301168
Engine Oil Filter Base - Disassemble
SMCS - 1306-015
Disassembly Procedure
Start By:
A. Remove the engine oil filter base and the oil cooler. Refer to Disassembly and Assembly,
"Engine Oil Filter Base and Oil Cooler - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Remote Mounted Engine Oil Filter Base
1/3
329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engi...
2020/4/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 1 g01152353
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove oil filter bypass valve (2) from engine oil filter base (1) .
Engine Mounted Engine Oil Filter Base
2/3
329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engi...
2020/4/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 2 g01152356
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove adapter (3) and the O-ring seals from engine oil filter base (4) .
2. Remove oil filter bypass valve (5) and oil filter bypass valve (6) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Apr 23 13:23:48 UTC+0800 2020
3/3
329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engi...
2020/4/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 329D LN EXCAVATOR SCY
Configuration: 329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02301184
Engine Oil Filter Base - Assemble
SMCS - 1306-016
Assembly Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Engine Mounted Engine Oil Filter Base
Table 1
Required Tools
Tool Part Number Part Description Qty
A 155-0695 Thread Lock Compound 1
1/3
329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engi...
2020/4/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 1 g01152356
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
1. Install oil filter bypass valve (6) and oil filter bypass valve (5) in engine oil filter base (4) .
2. Apply Tooling (A) to the threads of adapter (3). Install the O-ring seals and adapter (3).
Tighten adapter (3) to a torque of 150 ± 20 N·m (110 ± 15 lb ft).
Remote Mounted Engine Oil Filter Base
2/3
329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engi...
2020/4/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 2 g01152353
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
1. Install oil filter bypass valve (2) in engine oil filter base (1) .
End By: Install the engine oil filter base and the oil cooler. Refer to Disassembly and Assembly,
"Engine Oil Filter Base and Oil Cooler - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Apr 23 13:24:44 UTC+0800 2020
3/3
329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engi...
2020/4/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 329D LN EXCAVATOR SCY
Configuration: 329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02301151
Engine Oil Filter Base and Oil Cooler - Install
SMCS - 1306-012; 1378-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Engine Mounted Engine Oil Filter Base
1/3
329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engi...
2020/4/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 1 g01152340
1. Position the gasket and oil cooler (8) on the engine.
2. Install engine oil filter base (7) and bolts (6) .
3. Connect hose assembly (5) .
4. Connect hose assemblies (4) .
5. Fill the cooling system. Refer to Operation and Maintenance Manual, "Cooling System
Coolant - Change".
Remote Mounted Engine Oil Filter Base
2/3
329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engi...
2020/4/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Illustration 2 g01152338
1. Position engine oil filter base (3) and install bolts (2) .
2. Install engine oil filter (1) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Apr 23 13:25:39 UTC+0800 2020
3/3
329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engi...
2020/4/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 329D LN EXCAVATOR SCY
Configuration: 329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02301238
Engine Oil Pump - Remove
SMCS - 1304-011
Removal Procedure
Start By:
A. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engi...
2020/4/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 1 g01152440
1. Remove bracket (5) .
2. Remove pickup tube (4) and the gasket from engine oil pump (1) .
3. Remove outlet elbow (3) and the O-ring seals from engine oil pump (1) .
4. Remove bolts (2) and engine oil pump (1) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Apr 23 13:26:35 UTC+0800 2020
2/2
329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engi...
2020/4/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...