This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 320 excavator models. It describes the required tools and gives a step-by-step process including removing clips and pins, sliding tubes, and removing/installing parts like the governor, linkage, and seals using special tools. References are provided for more information on governors and linkage inspection procedures.
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 320 excavator models. It describes the required tools and gives a step-by-step process including removing clips and pins, sliding tubes, and removing/installing parts like the governor, linkage, and seals using special tools. References are provided for more information on governors and linkage inspection procedures.
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 320 excavator models. The removal procedure involves disconnecting tubes, clips, pins and bolts to separate the governor and linkage. The installation procedure specifies cleaning and lubricating parts, then reversing the removal steps and using various tools to properly position, connect and adjust the governor and linkage. Proper torque specifications are provided for bolts. References are made to other documents for additional information.
Caterpillar cat 320 a excavator (prefix 3 rk) service repair manual (3rk00001...fujsekfsmemm
This document provides instructions for removing and installing a governor and fuel injection control linkage on a 320-A excavator engine. The removal process involves disconnecting tubes, removing clips and pins connecting the governor. The installation involves cleaning and lubricating seals, installing the governor with new seals and pins, and connecting it to the control linkage. Special tools are required for tasks like inserting pins. References are provided for additional information on governors, linkages and engine components.
Caterpillar cat 320 l excavator (prefix 4 bk) service repair manual (4bk00001...ujfjjskkekmem
This document provides instructions for removing and installing a governor from a 320 L EXCAVATOR engine. The removal procedure involves disconnecting control cables, removing clips and tubes, and using special tools to remove the governor. The installation procedure outlines cleaning and lubricating parts, placing the governor back in position, reconnecting control links and tubes, and adjusting settings. Precise use of various specialty tools is required to properly complete the process.
Caterpillar cat 320 track type excavator (prefix 1 tl) service repair manual ...ufuusefjjsekkm
This document provides instructions for removing and installing a governor on a Caterpillar 320L excavator engine. It begins by listing the required tools. The removal procedure involves 11 steps that include disconnecting cables, removing clips and pins, and taking out bolts and seals. The installation procedure reverses these steps, applying lubricant to new seals and ensuring proper pin and clip installation. References are provided for additional information on governor calibration and inspection.
This document provides instructions for removing and installing a governor and fuel injection control linkage on an excavator engine. The removal procedure involves disconnecting cables, removing clips and pins, and taking off bolts. The installation involves applying lubricant to seals, placing parts in position, installing clips, pins and bolts using various specialized tools, and setting adjustments. Precautions are given to keep parts clean and ensure free movement of components.
Caterpillar cat 320 n track type excavator (prefix 2dl) service repair manual...ddkkddm
This document provides instructions for removing and installing valve stem seals on Caterpillar 320, 320L, and 320N track-type excavators. The procedure involves using a seal pick tool to remove the old seals from the valve guides and install new seals. Technicians are instructed to keep all parts clean and coat the new seals with engine oil during installation.
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. The procedure involves using specialty tools to compress the valve springs so that the valves, springs, and related components can be safely accessed and removed or installed one piston at a time. Proper tool use and safety precautions are emphasized to avoid injury from released spring forces.
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 320 excavator models. It describes the required tools and gives a step-by-step process including removing clips and pins, sliding tubes, and removing/installing parts like the governor, linkage, and seals using special tools. References are provided for more information on governors and linkage inspection procedures.
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 320 excavator models. The removal procedure involves disconnecting tubes, clips, pins and bolts to separate the governor and linkage. The installation procedure specifies cleaning and lubricating parts, then reversing the removal steps and using various tools to properly position, connect and adjust the governor and linkage. Proper torque specifications are provided for bolts. References are made to other documents for additional information.
Caterpillar cat 320 a excavator (prefix 3 rk) service repair manual (3rk00001...fujsekfsmemm
This document provides instructions for removing and installing a governor and fuel injection control linkage on a 320-A excavator engine. The removal process involves disconnecting tubes, removing clips and pins connecting the governor. The installation involves cleaning and lubricating seals, installing the governor with new seals and pins, and connecting it to the control linkage. Special tools are required for tasks like inserting pins. References are provided for additional information on governors, linkages and engine components.
Caterpillar cat 320 l excavator (prefix 4 bk) service repair manual (4bk00001...ujfjjskkekmem
This document provides instructions for removing and installing a governor from a 320 L EXCAVATOR engine. The removal procedure involves disconnecting control cables, removing clips and tubes, and using special tools to remove the governor. The installation procedure outlines cleaning and lubricating parts, placing the governor back in position, reconnecting control links and tubes, and adjusting settings. Precise use of various specialty tools is required to properly complete the process.
Caterpillar cat 320 track type excavator (prefix 1 tl) service repair manual ...ufuusefjjsekkm
This document provides instructions for removing and installing a governor on a Caterpillar 320L excavator engine. It begins by listing the required tools. The removal procedure involves 11 steps that include disconnecting cables, removing clips and pins, and taking out bolts and seals. The installation procedure reverses these steps, applying lubricant to new seals and ensuring proper pin and clip installation. References are provided for additional information on governor calibration and inspection.
This document provides instructions for removing and installing a governor and fuel injection control linkage on an excavator engine. The removal procedure involves disconnecting cables, removing clips and pins, and taking off bolts. The installation involves applying lubricant to seals, placing parts in position, installing clips, pins and bolts using various specialized tools, and setting adjustments. Precautions are given to keep parts clean and ensure free movement of components.
Caterpillar cat 320 n track type excavator (prefix 2dl) service repair manual...ddkkddm
This document provides instructions for removing and installing valve stem seals on Caterpillar 320, 320L, and 320N track-type excavators. The procedure involves using a seal pick tool to remove the old seals from the valve guides and install new seals. Technicians are instructed to keep all parts clean and coat the new seals with engine oil during installation.
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. The procedure involves using specialty tools to compress the valve springs so that the valves, springs, and related components can be safely accessed and removed or installed one piston at a time. Proper tool use and safety precautions are emphasized to avoid injury from released spring forces.
The document provides instructions for removing the fuel injection pump from a Caterpillar 320D L excavator with a C6.4 engine. It lists the required tools and safety notices, then gives a step-by-step procedure involving disconnecting fuel lines and harness assemblies, removing mounting hardware, and taking off the pump while keeping identification marks aligned for installation. Cleanliness is emphasized throughout to prevent contaminants from entering the system.
Caterpillar cat 320 l track type excavator (prefix 2dl) service repair manual...ddkkddm
This document provides instructions for installing and removing various engine components on Caterpillar 320, 320L, and 320N track-type excavators, including:
- Removing and installing inlet and exhaust valve seals
- Removing the engine oil filter base
- Installing the engine oil filter base
- Removing the engine oil cooler
- Disassembling the engine oil cooler
- Reassembling the engine oil cooler
- Installing the engine oil cooler
The summaries provide the main steps and components involved in each procedure.
This document provides instructions for connecting a separated track on a 320D LN excavator. It describes using hydraulic tools and pins to lift the track into position and connect the master pin. Cleanliness is important to prevent dirt from entering during reassembly. The track must be positioned correctly and tools are needed if the pin cannot be manually installed.
Caterpillar cat 320 d2 l excavator (prefix gba) service repair manual (gba000...ddkkddm
This document provides instructions for removing the fuel injector from a Caterpillar 320D2 excavator engine. It lists the required tools which include a fuel injector puller and capping kit. The procedure involves disconnecting fuel lines from the injector, plugging the injector, removing mounting bolts and clamps, and using a puller tool to remove the fuel injector from the engine. Care must be taken to contain any fluids and ensure all parts are clean.
Caterpillar cat 320 d2 l excavator (prefix dnp) service repair manual (dnp000...ddkkddm
The document provides instructions for assembling and installing the swing drive on a 320D2 excavator. It describes 22 steps to assemble components like bearings, gears, housings and seals. The final step is to install the assembled swing drive and refer to other instructions for installing the swing motor.
This document provides instructions for removing the fuel injector from a Caterpillar 320D2 excavator engine. It lists the required tools which include a fuel injector puller and capping kit. The procedure involves disconnecting fuel lines from the injector, plugging the injector, removing mounting bolts and clamps, and using a puller tool to remove the fuel injector from the engine. Care must be taken to contain any fluids and ensure all parts are clean.
The document provides instructions for assembling and installing the swing drive on a 320D2 excavator. It describes 22 steps to assemble components like bearings, gears, housings and seals. The final step is to install the assembled swing drive and refer to other instructions for installing the swing motor.
Caterpillar cat 320 d ln excavator (prefix wbn) service repair manual (wbn000...ddkkddm
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D LN excavator with a C6.4 engine. It describes the required tools and safety precautions, and gives a step-by-step process for compressing the valve springs, removing old parts, and installing new parts in their proper positions and orientations. The document also provides specifications for inspecting valve components to ensure proper dimensions are met.
Caterpillar cat 320 d l excavator (prefix kgf) service repair manual (kgf0000...ddkkddm
This document provides instructions for disassembling and assembling the travel motor of a 320D L excavator. The disassembly process includes 27 steps to remove components like the head, fittings, seals, brake piston, plates, and barrel assembly. The assembly section outlines 13 steps including installing seals, keys, cam plate, springs, and piston shoe assemblies back into the barrel assembly and body of the travel motor. Special notices are provided regarding alignment marks, pressing components, and engaging the cam plate during assembly.
Caterpillar cat 320 d l excavator (prefix dhk) service repair manual (dhk0000...ddkkddm
This document provides instructions for removing and installing a boom cylinder on a 320D excavator. It includes:
1) Detailed steps to remove the boom cylinder such as releasing hydraulic pressure, removing mounting bolts and pins, and lifting the cylinder off the machine.
2) Information on required tools and torque specifications for reassembly.
3) The installation procedure which reverses the removal steps such as lifting the cylinder back into place, reinstalling pins and bolts, and reconnecting hydraulic lines.
Safety precautions are provided to relieve hydraulic pressure before disassembling cylinders. Torque specifications are included for correct reassembly.
Caterpillar cat 320 d l excavator (prefix a9f) service repair manual (a9f0000...ddkkddm
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. The procedure involves using specialty tools to compress the valve springs so that the valves, springs, and related components can be safely accessed and removed or installed one at a time. Proper cleaning and inspection of parts is emphasized to prevent premature wear. The work must be done with the pistons positioned correctly to avoid parts falling into the cylinders.
Caterpillar cat 320 d excavator (prefix kgf) service repair manual (kgf00001 ...ddkkddm
This document provides instructions for disassembling and assembling the travel motor of a 320D L Excavator. The disassembly process includes 27 steps to remove components like the head, fittings, seals, brake piston, plates, and barrel assembly. The assembly section outlines 13 steps including installing seals, keys, cam plate, springs, and piston shoe assemblies back into the barrel assembly and travel motor body. Special care must be taken to align parts and not allow components to separate during disassembly and assembly.
Caterpillar cat 320 d excavator (prefix dhk) service repair manual (dhk00001 ...ddkkddm
This document provides instructions for removing and installing the boom cylinder on a 320D and 320D L excavator. The procedure involves releasing hydraulic pressure, removing attachment points, and using lifting devices to maneuver the heavy cylinder. Special tools are required to remove pins connecting the cylinder. Torque specifications are provided for reinstallation. Safety precautions are described, such as relieving pressure before disassembly to avoid injury.
Caterpillar cat 320 track type excavator (prefix 2 dl) service repair manual ...ddkkddm
This document provides instructions for removing and installing valve stem seals on Caterpillar 320, 320L, and 320N track-type excavators. The procedure involves using a seal pick tool to remove the old seals from the valve guides and install new seals. Technicians are instructed to keep all parts clean and coat the new seals with engine oil during installation.
Caterpillar cat 320 s excavator (prefix 4 zj) service repair manual (4zj00460...ddkkddm
1. The document provides instructions for removing and installing final drives on 320-series excavators. It describes disconnecting hydraulic lines, removing mounting bolts, and using lifting tools to remove the final drives from the excavator.
2. Detailed steps are given for disassembling the final drives, including removing gears, carriers, seals, and other components. Alignment marks should be made for reassembly.
3. Reassembly involves cleaning parts, applying threadlock and lubricant, and torquing bolts to specification. Seals and bearings must be installed correctly to prevent damage.
Caterpillar cat 320 n excavator (prefix 4 zj) service repair manual (4zj00460...ddkkddm
1. The document provides instructions for removing and installing final drives on 320-series excavators. It describes disconnecting hydraulic lines, removing mounting bolts, and using hoists to lift heavy components like the final drive, ring gear, and carrier assemblies.
2. Detailed steps are given for disassembling the final drive components, including removing planetary gears, sun gears, and thrust washers. Special tools and alignment marks are used to aid reassembly.
3. Reassembly involves cleaning components, applying threadlock and anti-seize compound, and adjusting bearing preload with shims to achieve the correct specifications. Duo-Cone seals must be installed without damage to provide sealing between housings.
Caterpillar cat 320 n excavator (prefix 3 xk) service repair manual (3xk00822...ddkkddm
This document provides instructions for removing and installing a fuel injection control linkage on Caterpillar 320 excavator models. The removal procedure involves taking out the rocker shaft and pushrods, then removing clips and a clevis pin connecting the governor to the linkage. Installation requires reattaching the linkage with bolts and setting brackets, then inserting the clevis pin and clip using special tools. Compressing injector springs with another tool is also part of the installation process.
Caterpillar cat 320 l excavator (prefix 4 zj) service repair manual (4zj00460...ddkkddm
This document provides instructions for removing and installing final drives on 320-series excavators. It outlines the steps to release hydraulic pressure, remove the final drive housing, and disassemble/reassemble the internal components. The process involves removing 20 bolts, hydraulic lines, and using lifting tools to maneuver heavy internal parts like carriers, gears, and housings weighing up to 82 kg. Proper cleaning, lubrication, and torque specifications are noted to ensure correct reassembly.
Caterpillar cat 320 l excavator (prefix 3 xk) service repair manual (3xk00822...ddkkddm
This document provides instructions for removing and installing a fuel injection control linkage on Caterpillar 320 excavator models. The removal procedure involves taking out the rocker shaft and pushrods, then removing clips and a clevis pin connecting the governor to the linkage. Installation requires reattaching the linkage with bolts and setting brackets, then inserting the clevis pin and clip using special tools. Compressing injector springs with another tool is also part of the installation process.
The document provides instructions for disassembling and assembling the travel motor of a 320 GC excavator. It lists the required tools and parts. The disassembly process involves removing plugs and seals from the motor housing. Springs must be released carefully due to risk of injury. The brake piston is then unseated using air pressure before internal components of the motor can be accessed and replaced. The assembly procedure reverses the disassembly steps.
The document provides instructions for removing the fuel injection pump from a Caterpillar 320D L excavator with a C6.4 engine. It lists the required tools and safety notices, then gives a step-by-step procedure involving disconnecting fuel lines and harness assemblies, removing mounting hardware, and taking off the pump while keeping identification marks aligned for installation. Cleanliness is emphasized throughout to prevent contaminants from entering the system.
Caterpillar cat 320 l track type excavator (prefix 2dl) service repair manual...ddkkddm
This document provides instructions for installing and removing various engine components on Caterpillar 320, 320L, and 320N track-type excavators, including:
- Removing and installing inlet and exhaust valve seals
- Removing the engine oil filter base
- Installing the engine oil filter base
- Removing the engine oil cooler
- Disassembling the engine oil cooler
- Reassembling the engine oil cooler
- Installing the engine oil cooler
The summaries provide the main steps and components involved in each procedure.
This document provides instructions for connecting a separated track on a 320D LN excavator. It describes using hydraulic tools and pins to lift the track into position and connect the master pin. Cleanliness is important to prevent dirt from entering during reassembly. The track must be positioned correctly and tools are needed if the pin cannot be manually installed.
Caterpillar cat 320 d2 l excavator (prefix gba) service repair manual (gba000...ddkkddm
This document provides instructions for removing the fuel injector from a Caterpillar 320D2 excavator engine. It lists the required tools which include a fuel injector puller and capping kit. The procedure involves disconnecting fuel lines from the injector, plugging the injector, removing mounting bolts and clamps, and using a puller tool to remove the fuel injector from the engine. Care must be taken to contain any fluids and ensure all parts are clean.
Caterpillar cat 320 d2 l excavator (prefix dnp) service repair manual (dnp000...ddkkddm
The document provides instructions for assembling and installing the swing drive on a 320D2 excavator. It describes 22 steps to assemble components like bearings, gears, housings and seals. The final step is to install the assembled swing drive and refer to other instructions for installing the swing motor.
This document provides instructions for removing the fuel injector from a Caterpillar 320D2 excavator engine. It lists the required tools which include a fuel injector puller and capping kit. The procedure involves disconnecting fuel lines from the injector, plugging the injector, removing mounting bolts and clamps, and using a puller tool to remove the fuel injector from the engine. Care must be taken to contain any fluids and ensure all parts are clean.
The document provides instructions for assembling and installing the swing drive on a 320D2 excavator. It describes 22 steps to assemble components like bearings, gears, housings and seals. The final step is to install the assembled swing drive and refer to other instructions for installing the swing motor.
Caterpillar cat 320 d ln excavator (prefix wbn) service repair manual (wbn000...ddkkddm
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D LN excavator with a C6.4 engine. It describes the required tools and safety precautions, and gives a step-by-step process for compressing the valve springs, removing old parts, and installing new parts in their proper positions and orientations. The document also provides specifications for inspecting valve components to ensure proper dimensions are met.
Caterpillar cat 320 d l excavator (prefix kgf) service repair manual (kgf0000...ddkkddm
This document provides instructions for disassembling and assembling the travel motor of a 320D L excavator. The disassembly process includes 27 steps to remove components like the head, fittings, seals, brake piston, plates, and barrel assembly. The assembly section outlines 13 steps including installing seals, keys, cam plate, springs, and piston shoe assemblies back into the barrel assembly and body of the travel motor. Special notices are provided regarding alignment marks, pressing components, and engaging the cam plate during assembly.
Caterpillar cat 320 d l excavator (prefix dhk) service repair manual (dhk0000...ddkkddm
This document provides instructions for removing and installing a boom cylinder on a 320D excavator. It includes:
1) Detailed steps to remove the boom cylinder such as releasing hydraulic pressure, removing mounting bolts and pins, and lifting the cylinder off the machine.
2) Information on required tools and torque specifications for reassembly.
3) The installation procedure which reverses the removal steps such as lifting the cylinder back into place, reinstalling pins and bolts, and reconnecting hydraulic lines.
Safety precautions are provided to relieve hydraulic pressure before disassembling cylinders. Torque specifications are included for correct reassembly.
Caterpillar cat 320 d l excavator (prefix a9f) service repair manual (a9f0000...ddkkddm
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. The procedure involves using specialty tools to compress the valve springs so that the valves, springs, and related components can be safely accessed and removed or installed one at a time. Proper cleaning and inspection of parts is emphasized to prevent premature wear. The work must be done with the pistons positioned correctly to avoid parts falling into the cylinders.
Caterpillar cat 320 d excavator (prefix kgf) service repair manual (kgf00001 ...ddkkddm
This document provides instructions for disassembling and assembling the travel motor of a 320D L Excavator. The disassembly process includes 27 steps to remove components like the head, fittings, seals, brake piston, plates, and barrel assembly. The assembly section outlines 13 steps including installing seals, keys, cam plate, springs, and piston shoe assemblies back into the barrel assembly and travel motor body. Special care must be taken to align parts and not allow components to separate during disassembly and assembly.
Caterpillar cat 320 d excavator (prefix dhk) service repair manual (dhk00001 ...ddkkddm
This document provides instructions for removing and installing the boom cylinder on a 320D and 320D L excavator. The procedure involves releasing hydraulic pressure, removing attachment points, and using lifting devices to maneuver the heavy cylinder. Special tools are required to remove pins connecting the cylinder. Torque specifications are provided for reinstallation. Safety precautions are described, such as relieving pressure before disassembly to avoid injury.
Caterpillar cat 320 track type excavator (prefix 2 dl) service repair manual ...ddkkddm
This document provides instructions for removing and installing valve stem seals on Caterpillar 320, 320L, and 320N track-type excavators. The procedure involves using a seal pick tool to remove the old seals from the valve guides and install new seals. Technicians are instructed to keep all parts clean and coat the new seals with engine oil during installation.
Caterpillar cat 320 s excavator (prefix 4 zj) service repair manual (4zj00460...ddkkddm
1. The document provides instructions for removing and installing final drives on 320-series excavators. It describes disconnecting hydraulic lines, removing mounting bolts, and using lifting tools to remove the final drives from the excavator.
2. Detailed steps are given for disassembling the final drives, including removing gears, carriers, seals, and other components. Alignment marks should be made for reassembly.
3. Reassembly involves cleaning parts, applying threadlock and lubricant, and torquing bolts to specification. Seals and bearings must be installed correctly to prevent damage.
Caterpillar cat 320 n excavator (prefix 4 zj) service repair manual (4zj00460...ddkkddm
1. The document provides instructions for removing and installing final drives on 320-series excavators. It describes disconnecting hydraulic lines, removing mounting bolts, and using hoists to lift heavy components like the final drive, ring gear, and carrier assemblies.
2. Detailed steps are given for disassembling the final drive components, including removing planetary gears, sun gears, and thrust washers. Special tools and alignment marks are used to aid reassembly.
3. Reassembly involves cleaning components, applying threadlock and anti-seize compound, and adjusting bearing preload with shims to achieve the correct specifications. Duo-Cone seals must be installed without damage to provide sealing between housings.
Caterpillar cat 320 n excavator (prefix 3 xk) service repair manual (3xk00822...ddkkddm
This document provides instructions for removing and installing a fuel injection control linkage on Caterpillar 320 excavator models. The removal procedure involves taking out the rocker shaft and pushrods, then removing clips and a clevis pin connecting the governor to the linkage. Installation requires reattaching the linkage with bolts and setting brackets, then inserting the clevis pin and clip using special tools. Compressing injector springs with another tool is also part of the installation process.
Caterpillar cat 320 l excavator (prefix 4 zj) service repair manual (4zj00460...ddkkddm
This document provides instructions for removing and installing final drives on 320-series excavators. It outlines the steps to release hydraulic pressure, remove the final drive housing, and disassemble/reassemble the internal components. The process involves removing 20 bolts, hydraulic lines, and using lifting tools to maneuver heavy internal parts like carriers, gears, and housings weighing up to 82 kg. Proper cleaning, lubrication, and torque specifications are noted to ensure correct reassembly.
Caterpillar cat 320 l excavator (prefix 3 xk) service repair manual (3xk00822...ddkkddm
This document provides instructions for removing and installing a fuel injection control linkage on Caterpillar 320 excavator models. The removal procedure involves taking out the rocker shaft and pushrods, then removing clips and a clevis pin connecting the governor to the linkage. Installation requires reattaching the linkage with bolts and setting brackets, then inserting the clevis pin and clip using special tools. Compressing injector springs with another tool is also part of the installation process.
The document provides instructions for disassembling and assembling the travel motor of a 320 GC excavator. It lists the required tools and parts. The disassembly process involves removing plugs and seals from the motor housing. Springs must be released carefully due to risk of injury. The brake piston is then unseated using air pressure before internal components of the motor can be accessed and replaced. The assembly procedure reverses the disassembly steps.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320 L EXCAVATOR 3XK
Configuration: 320, 320 L, 320 N AND 320 S EXCAVATORS 3XK00822-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01928381
Governor - Remove
SMCS - 1264-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 136-4149 Governor Pliers(1)
1
(1)
This tool is part of the 128-8822 Fuel System and Governor Tool Group.
Start By:
a. Remove the fuel shutoff solenoid. Refer to Disassembly and Assembly, "Fuel Shutoff
Solenoid - Remove and Install".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/5(W)
w
2019/12/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
3. Illustration 1 g00613041
1. Disconnect the governor control cable.
2. Remove oil tube assembly (1). Remove tube assembly (2) and tube assembly for fuel ratio
control (3), if equipped. Plug and cap all connections.
Illustration 2 g00613071
3. Remove clip (4).
2/5(W)
w
2019/12/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
4. Illustration 3 g00655975
4. Use Tooling (A) to slide tube assembly (5) into the cylinder head.
Illustration 4 g00613149
5. Remove the clip and use Tooling (A) to remove the clevis pin (6).
Note: Clevis pin (6) must stay with the governor in order to be adjusted.
3/5(W)
w
2019/12/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
5. Illustration 5 g00613563
6. Remove bolts (7) and the washers that hold the governor in position.
Illustration 6 g00673182
7. Remove the governor from the engine.
Illustration 7 g00673180
8. Remove O-ring seal (3) on the governor.
Illustration 8 g00672742
4/5(W)
w
2019/12/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
6. 9. Remove the O-ring seal and tube assembly (5) from the cylinder head.
Illustration 9 g00672733
10. Remove O-ring seal (2) on the tube assembly (5).
Illustration 10 g00673178
11. Remove O-ring seal (1) from the cylinder head.
Note: For more information on the governor, refer to Service Manual, SENR6454, "3114, 3116, &
3126 Engine Governors". The Service Manual, SENR6454 requires the use of a 1U-7326
Governor Calibration Bench. For information on reusability of components in the governor, refer
to Guideline For Reusable Parts And Salvage Operations, SEBF8434, "3100 Governor Inspection
and General Information for Mechanical Governor Groups Used in 3114, 3116, and 3126 Engines
Equipped with Mechanical Unit Injectors (MUI)".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Dec 29 15:10:10 UTC+0800 2019
5/5(W)
w
2019/12/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
7. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320 L EXCAVATOR 3XK
Configuration: 320, 320 L, 320 N AND 320 S EXCAVATORS 3XK00822-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01928419
Governor - Install
SMCS - 1264-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 136-4149 Governor Pliers(1)
1
B
128-8827 Pin(1)
1
1U-7523 Pin Pilot(1)
1
(1)
This tool is part of the 128-8822 Governor Tool Group.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For more information on the governor, refer to Service Manual, SENR6454, "3114, 3116, &
3126 Engine Governors". The Service Manual, SENR6454 requires the use of a 1U-7326
Governor Calibration Bench. For information on reusability of components in the governor, refer
to Guideline For Reusable Parts And Salvage Operations, SEBF8434, "3100 Governor Inspection
and General Information for Mechanical Governor Groups Used in 3114, 3116, and 3126 Engines
Equipped with Mechanical Unit Injectors (MUI)".
1/5(W)
w
2019/12/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
8. Illustration 1 g00673178
1. Apply lubricant to the new O-ring seal (1). Install new O-ring seal (1) in the cylinder head.
Illustration 2 g00672733
2. Apply lubricant to the new O-ring seal (2). Install new O-ring seal (2) on the tube assembly
(5).
Illustration 3 g00672742
3. Install the O-ring seal and tube assembly (5) in the cylinder head.
2/5(W)
w
2019/12/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
9. Illustration 4 g00673180
4. Apply lubricant to the new O-ring seal (3). Install new O-ring seal (3) on the governor.
Illustration 5 g00673182
5. Place the governor in position on the engine.
Illustration 6 g00613563
6. Install the washers and bolts (7) that hold the governor in place.
3/5(W)
w
2019/12/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
10. Illustration 7 g00672755
7. Install clevis pin (6) in Tooling (B).
Illustration 8 g00672752
8. Use Tooling (B) to install clevis pin (6) and the clip.
9. Check the fuel setting adjustment. Refer to Testing and Adjusting, SENR5118.
4/5(W)
w
2019/12/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
11. Illustration 9 g00655975
10. Use Tooling (A) to slide tube assembly (5) into the governor.
Illustration 10 g00613071
11. Install clip (4).
Illustration 11 g00613041
12. Install oil tube assembly (1). Install tube assembly (2) and tube assembly for fuel ratio
control (3), if equipped. Plug and cap all connections.
13. Install the governor control cable.
End By:
a. Install the fuel shutoff solenoid. Refer to Disassembly and Assembly, "Fuel Shutoff
Solenoid - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Dec 29 15:11:06 UTC+0800 2019
5/5(W)
w
2019/12/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320 L EXCAVATOR 3XK
Configuration: 320, 320 L, 320 N AND 320 S EXCAVATORS 3XK00822-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01928445
Fuel Injection Control Linkage - Remove
SMCS - 1298-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 136-4149 Governor Pliers 1
Start By:
a. Remove the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrod - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3(W)
w
2019/12/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
13. Illustration 1 g00613071
1. Remove clip (4). Clip (4) is located between the governor and the cylinder head.
Illustration 2 g00655975
2. Use Tooling (A) to slide tube assembly (5) into the cylinder head.
Illustration 3 g00613149
2/3(W)
w
2019/12/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
14. 3. Remove the clip and use Tooling (A) to remove the clevis pin (6). Clevis pin (6) connects
the governor to the control lever of the fuel injection control linkage.
Note: Clevis pin (6) must stay with the governor in order to be adjusted.
Illustration 4 g00630566
4. Remove bolts (1) and remove fuel injection control linkage (2). Control lever (3) connects
the fuel injection control linkage (2) to the governor.
Note: For information on the inspection procedure for control lever (3), refer to Special
Instruction, REHS0601, "Inspection and Modification of the 102-7459 Fuel Injection
Control Linkage and the 4P-9048 Fuel Injection Control Linkage".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Dec 29 15:12:01 UTC+0800 2019
3/3(W)
w
2019/12/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320 L EXCAVATOR 3XK
Configuration: 320, 320 L, 320 N AND 320 S EXCAVATORS 3XK00822-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines, IT18F
Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01928573
Fuel Injection Control Linkage - Install
SMCS - 1298-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 136-4149 Governor Pliers(1)
1
B
128-8827 Pin(1)
1
1U-7523 Pin Pilot(1)
1
C 1U-6675 Spring Compressor(1)
6
D 128-8822 Fuel System and Governor Tool Gp 1
(1)
This tool is part of the 128-8822 Governor Tool Group.
1/4(W)
w
2019/12/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
16. Illustration 1 g00661331
Note: For information on the inspection procedure for control lever (3), refer to Special Instruction,
REHS0601, "Inspection and Modification of the 102-7459 Fuel Injection Control Linkage and the 4P
-9048 Fuel Injection Control Linkage".
1. Loosen setscrews (4) on each bracket.
2. Install fuel control linkage (2) and install bolts (1). Use the following sequence in order to tighten the
bolts.
3. Tighten bracket (A) and (D) to a torque of 12 ± 3 N·m (106 ± 27 lb in).
4. Tighten brackets (B) and (C) to a torque of 12 ± 3 N·m (106 ± 27 lb in).
5. Position brackets (B) and (C) in order to allow free rotation of the fuel control rod.
6. Use a 2.5 mm (0.10 inch) wrench to tighten setscrews (4). Tighten the setscrews to a torque of
3.5 ± 0.2 N·m (31 ± 2 lb in). Do not overtighten the setscrews. Ensure that the control rod rotates
freely.
7. The control rod should rotate freely when a force of 4.4 N (1 lb) or less is applied to control lever
(3).
Illustration 2 g00750163
8. Rotate the unit injectors in order to engage the injector rack bar (5) with the fuel injection control
linkage (2).
Note: If the unit injectors are not installed, refer to the Disassembly and Assembly, "Unit Injector -
Install".
2/4(W)
w
2019/12/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
17. 9. Install Tooling (C) on the unit injectors and compress the springs.
Note: For the procedure to install Tooling (C), refer to Tool Operating Manual, NEHS0610, "Using
the 128-8822 Tool Group on 3114, 3116, and 3126 Engines with Mechanical Unit Injectors (MUI)".
Illustration 3 g00672755
10. Install clevis pin (6) in Tooling (B). Clevis pin (6) attaches the control lever (3) to the governor.
Illustration 4 g00672752
11. Use Tooling (B) to install clevis pin (6) and the clip.
12. Use Tooling (D) to set the unit injector synchronization.
Note: For the procedure to use Tooling (D), refer to Tool Operating Manual, NEHS0610, "Using the
128-8822 Tool Group on 3114, 3116, and 3126 Engines with Mechanical Unit Injectors (MUI)".
13. Remove Tooling (C) from the unit injectors.
3/4(W)
w
2019/12/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
18. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
19. Illustration 5 g00655975
14. Use Tooling (A) to slide tube assembly (5) into the governor.
Illustration 6 g00613071
15. Install clip (4).
End By:
a. Install the rocker arm assemblies and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrod - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Dec 29 15:12:57 UTC+0800 2019
4/4(W)
w
2019/12/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320 L EXCAVATOR 3XK
Configuration: 320, 320 L, 320 N AND 320 S EXCAVATORS 3XK00822-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i05919358
Unit Injector - Remove
SMCS - 1290-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-0302 Bar 1
Start By:
A. Remove the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrod - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/3(W)
w
2019/12/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
21. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00775441
2/3(W)
w
2019/12/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
22. Illustration 2 g00625237
1. Remove fuel injector hold-down bolt (1) .
Note: Do not pry on the injector hold-down bracket. Damage to the unit injector could
occur. The unit injector has a notch on the opposite side of the rack. This notch is used for
prying the unit injector loose. Some fuel injector racks move freely when the spring is not
compressed. Do not move the fuel injector rack without compressing the fuel injector spring
slightly. Damage may occur to the unit injector.
2. Use Tooling (A) to loosen the unit injector. Rotate the unit injector in order to disengage
injector rack bar (3) from fuel injection control linkage (2) .
3. Remove the unit injector. Ensure that two O-ring seals are on the unit injector.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Dec 29 15:13:53 UTC+0800 2019
3/3(W)
w
2019/12/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...