The document provides instructions for disassembling a travel motor. It describes 28 steps to remove components such as the head, springs, seals, plates, pistons, bearings, and housing. Tools include an adapter, bolts, nuts, threaded rods, retaining ring pliers, a bearing puller, eyebolts, and a push-puller plate. Safety precautions are provided to avoid injury from released spring forces during disassembly.
Caterpillar cat 374 f l excavator (prefix mfl) service repair manual (mfl0000...fjkskedmme
This document provides instructions for disassembling and assembling the final drive on a 374F L Excavator. The disassembly process involves removing over 30 individual parts in a specific sequence, including carrier assemblies, gears, shafts, seals, and housings. The assembly process reverses the disassembly steps and provides details on installing new seals, applying thread locking compounds, and lifting components into place using specialized tools. Precise following of the step-by-step instructions is required to correctly take apart and rebuild the final drive transmission.
Caterpillar cat 323 e l excavator (prefix tdw) service repair manual (tdw0000...fjskefkemms
This document provides assembly and disassembly instructions for a swing drive on excavator models 323E L, 323E LN, and 323E SA. It includes 21 steps for disassembly and 18 steps for assembly. Key steps include using retaining ring pliers and pullers to remove gears, carriers, shafts, and seals from the housing. Assembly involves pressing components back into place, applying threadlocker, and torquing bolts to specifications. The document provides detailed illustrations and lists required tools for each step.
Caterpillar cat 330 f excavator (prefix hbt) service repair manual (hbt00001 ...fjskekdmjekm
This document provides instructions for removing and installing a front cover on a 330F excavator engine. The key steps are:
1. Remove the crankshaft pulley, fan if equipped, and front seal from the front cover.
2. Remove bolts from the front cover and housing, then remove the cover and gasket.
3. Clean the cover, housing, and install a new gasket. Use guide studs to position the cover and hand tighten bolts.
4. Align the cover and tighten the bolts. Install a new front seal. Reinstall the pulley, fan if equipped.
The document provides instructions for disassembling and assembling a travel motor. It lists 28 steps for disassembly, removing components like the head, port plate, springs, brake piston, plates and discs. It then lists 23 steps for assembly, installing components in reverse order like the brake piston, plates and discs, cam plate, seals and covers. Special tools are listed and safety notices are provided throughout regarding cleaning, handling springs, and aligning parts.
Caterpillar cat 319 d l excavator (prefix rjp) service repair manual (rjp0000...fjkskedmme
The document provides instructions for disassembling and assembling a final drive on a 319D L and 319D LN excavator. The disassembly procedure involves removing 33 individual parts from the final drive including the cover, carrier assembly, ring gears, and main housing. The assembly procedure instructs installing 31 of the parts back into the final drive in reverse order and provides details on properly preloading the bearings and determining the correct shim thickness.
Caterpillar cat 330 l excavator (prefix 8fk) service repair manual (8fk00001 ...fjsjekdmmeme
This document provides instructions for removing and installing a cylinder head on a 330L excavator with a 3306 engine. The key steps are:
1. Remove components attached to the cylinder head like the exhaust manifold, fuel lines, and rocker shaft.
2. Remove the cylinder head bolts and lifting the heavy cylinder head off the engine.
3. Clean the mating surfaces and install a new gasket before reinstalling the cylinder head and torquing the bolts in the specified sequence.
4. Reinstall the removed components like the rocker shaft after installing the new cylinder head.
Caterpillar cat 330 d l mobile hydraulic excavator (prefix h3d) service repai...hhjsekmdmm
This document provides instructions for removing and installing the rear gear group and crankshaft rear seal on a 330D L excavator. The removal procedure involves using various tools to remove bolts, gears, bushings, bearings, and covers. Precautions are listed to keep parts clean and prevent damage. The installation procedure specifies how to position gears, bearings, seals and other components, applying threadlock and noting torque specifications. Dimensions and angles are provided to ensure proper installation of bearings.
Caterpillar cat 320 d lrr excavator (prefix gmx) service repair manual (gmx00...fjkskedmme
This document provides instructions for removing and installing various engine components on a Caterpillar 320D RR excavator, including:
- Removing and installing the flywheel using various tools
- Removing and installing the crankshaft rear seal
- Removing and installing the flywheel housing
- Removing and installing the crankshaft pulley
The summaries provide an overview of the component being worked on and refer the user to the detailed instructions and illustrations in the document.
Caterpillar cat 374 f l excavator (prefix mfl) service repair manual (mfl0000...fjkskedmme
This document provides instructions for disassembling and assembling the final drive on a 374F L Excavator. The disassembly process involves removing over 30 individual parts in a specific sequence, including carrier assemblies, gears, shafts, seals, and housings. The assembly process reverses the disassembly steps and provides details on installing new seals, applying thread locking compounds, and lifting components into place using specialized tools. Precise following of the step-by-step instructions is required to correctly take apart and rebuild the final drive transmission.
Caterpillar cat 323 e l excavator (prefix tdw) service repair manual (tdw0000...fjskefkemms
This document provides assembly and disassembly instructions for a swing drive on excavator models 323E L, 323E LN, and 323E SA. It includes 21 steps for disassembly and 18 steps for assembly. Key steps include using retaining ring pliers and pullers to remove gears, carriers, shafts, and seals from the housing. Assembly involves pressing components back into place, applying threadlocker, and torquing bolts to specifications. The document provides detailed illustrations and lists required tools for each step.
Caterpillar cat 330 f excavator (prefix hbt) service repair manual (hbt00001 ...fjskekdmjekm
This document provides instructions for removing and installing a front cover on a 330F excavator engine. The key steps are:
1. Remove the crankshaft pulley, fan if equipped, and front seal from the front cover.
2. Remove bolts from the front cover and housing, then remove the cover and gasket.
3. Clean the cover, housing, and install a new gasket. Use guide studs to position the cover and hand tighten bolts.
4. Align the cover and tighten the bolts. Install a new front seal. Reinstall the pulley, fan if equipped.
The document provides instructions for disassembling and assembling a travel motor. It lists 28 steps for disassembly, removing components like the head, port plate, springs, brake piston, plates and discs. It then lists 23 steps for assembly, installing components in reverse order like the brake piston, plates and discs, cam plate, seals and covers. Special tools are listed and safety notices are provided throughout regarding cleaning, handling springs, and aligning parts.
Caterpillar cat 319 d l excavator (prefix rjp) service repair manual (rjp0000...fjkskedmme
The document provides instructions for disassembling and assembling a final drive on a 319D L and 319D LN excavator. The disassembly procedure involves removing 33 individual parts from the final drive including the cover, carrier assembly, ring gears, and main housing. The assembly procedure instructs installing 31 of the parts back into the final drive in reverse order and provides details on properly preloading the bearings and determining the correct shim thickness.
Caterpillar cat 330 l excavator (prefix 8fk) service repair manual (8fk00001 ...fjsjekdmmeme
This document provides instructions for removing and installing a cylinder head on a 330L excavator with a 3306 engine. The key steps are:
1. Remove components attached to the cylinder head like the exhaust manifold, fuel lines, and rocker shaft.
2. Remove the cylinder head bolts and lifting the heavy cylinder head off the engine.
3. Clean the mating surfaces and install a new gasket before reinstalling the cylinder head and torquing the bolts in the specified sequence.
4. Reinstall the removed components like the rocker shaft after installing the new cylinder head.
Caterpillar cat 330 d l mobile hydraulic excavator (prefix h3d) service repai...hhjsekmdmm
This document provides instructions for removing and installing the rear gear group and crankshaft rear seal on a 330D L excavator. The removal procedure involves using various tools to remove bolts, gears, bushings, bearings, and covers. Precautions are listed to keep parts clean and prevent damage. The installation procedure specifies how to position gears, bearings, seals and other components, applying threadlock and noting torque specifications. Dimensions and angles are provided to ensure proper installation of bearings.
Caterpillar cat 320 d lrr excavator (prefix gmx) service repair manual (gmx00...fjkskedmme
This document provides instructions for removing and installing various engine components on a Caterpillar 320D RR excavator, including:
- Removing and installing the flywheel using various tools
- Removing and installing the crankshaft rear seal
- Removing and installing the flywheel housing
- Removing and installing the crankshaft pulley
The summaries provide an overview of the component being worked on and refer the user to the detailed instructions and illustrations in the document.
Caterpillar cat 319 d l excavator (prefix wbj) service repair manual (wbj0000...fjkskedmme
The document provides instructions for disassembling and assembling a final drive component of a 319D LN excavator. It includes 33 steps for disassembly, removing components like the cover, carrier assembly, ring gears, and seals. The assembly section has 13 steps, including preloading the bearings to determine the correct shim thickness, installing seals and pins, and attaching the main housing to the motor housing. Precise cleaning and use of replacement parts is emphasized throughout.
Caterpillar cat 330 d excavator (prefix nbd) service repair manual (nbd00001 ...hhjsekmdmm
The document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive. Key components that are disassembled include the drive housing, planetary gear assemblies, ring gear, carrier assemblies, and individual planet gears. Tools required include link brackets and forcing bolts to remove components. Safety notes are provided to clean parts before disassembly and have two people assist with heavier components.
Caterpillar cat 320 d rr excavator (prefix yds) service repair manual (yds000...fjkskedmme
This document provides instructions for disassembling and assembling the travel motor on a 320D RR excavator. It lists the required tools and parts. The disassembly procedure involves removing 25 components from the travel motor in a specific sequence. The assembly procedure instructs putting the travel motor back together in the reverse order and provides important notes to ensure proper installation.
Caterpillar cat 390 f excavator (prefix hng) service repair manual (hng00001 ...fjskefksemer
This document provides instructions for removing and installing the front gear group of a C18 engine. The removal procedure involves removing 14 bolts, plates, gears and seals. Special care must be taken to mark gear orientations and not turn the crankshaft during removal. The installation procedure describes cleaning components, applying thread lock compound, installing 14 gears, plates and seals in the correct order and orientation, and adjusting backlash between gears. Proper removal and installation is important to avoid engine damage.
Caterpillar cat 950 f wheel loader (prefix 4dj) service repair manual (4dj000...ifkkdmdmdm
This document provides step-by-step instructions for disassembling the transmission of a 950F Wheel Loader model. It lists 79 steps to remove various transmission components including the torque converter, transmission control valve, carrier assemblies, planetary gears, clutches, seals, and housing components. Detailed diagrams accompany each step to illustrate the proper procedure and required tooling.
Caterpillar cat 325 f excavator (prefix ndj) service repair manual (ndj00001 ...hfjsekekmmd
The document provides instructions for disassembling and assembling the travel motor of a 325F excavator. It includes 30 steps for disassembly, removing components like the spring, spool, relief valve, head assembly, housing assembly and more. The 31 steps for assembly include installing seals, springs, pistons, cam plate, barrel assembly and ensuring proper alignment of components. Special tools and precautions are noted to properly release spring forces and prevent damage during assembly.
Caterpillar cat 374 d l excavator (prefix pax) service repair manual (pax0000...fjkskedmme
The document provides instructions for disassembling and assembling components of a 374D L excavator travel motor and final drive system. It describes 17 steps to disassemble the final drive, including removing the final drive cover, ring gear, sun gears, carrier assemblies, planetary gears and shafts. Tools required include a transmission repair stand, link brackets, hydraulic wrench, hex bit socket and forcing bolts. Marks must be made to indicate original part locations for reassembly.
Caterpillar cat 325 d mobile hyd power unit (prefix c3n) service repair manua...fikkskmmdm
The document provides instructions for removing and installing an alternator from an engine that is still installed in a machine. The procedure involves:
1. Disconnecting the positive battery terminal to prevent wiring damage.
2. Removing the belt from the alternator pulley.
3. Removing bolts securing the alternator and removing it from the engine.
4. Installing the new alternator using the securing bolts and adjusting the belt tension.
Caterpillar cat 320 d lrr excavator (prefix fxk) service repair manual (fxk00...fjkskedmme
This document provides instructions for removing and installing the crankshaft and crankshaft gear on Caterpillar 3064 and 3066 engines. It outlines the required tools and step-by-step procedures for removing components like the main bearings, connecting rod caps, and crankshaft. Instructions are provided for checking clearances and installing each part in reverse order. Proper cleaning and lubrication of parts is emphasized to prevent premature wear.
Caterpillar cat 318 f l excavator (prefix hcp) service repair manual (hcp0000...fjkskedmme
This document provides instructions for disassembling and assembling the travel motor of a 318F L Excavator. It lists the required tools and presents 31 steps for disassembly, including removing components like the springs, spools, caps, and head assembly. It then lists 29 steps for assembly, instructing technicians to install these components in reverse order. Safety warnings are provided throughout to avoid injury from spring forces. The document is intended to guide maintenance technicians through a complete travel motor overhaul.
Caterpillar cat 329 e excavator (prefix k2l) service repair manual (k2l00001 ...fikkskmmdm
This document provides instructions for disassembling and assembling the travel motor of a 329E Mobile Hydraulic Power Unit. It lists 28 steps for disassembly, removing components like the head, brake piston, rotating assembly, and seals. It then lists 23 steps for assembly, reinstalling those components in reverse order while noting proper lubrication and alignment of parts. Tools required are also listed.
The document provides instructions for disassembling and assembling the travel motor of a 320 GC excavator. It lists the required tools and parts. The disassembly process involves removing plugs and seals from the motor housing. Springs must be released carefully due to risk of injury. The brake piston is then unseated using air pressure before internal components of the motor can be accessed and replaced. The assembly procedure reverses the disassembly steps.
Caterpillar cat 325 d mh excavator (prefix rjk) service repair manual (rjk000...fjsekkdmme
This document provides instructions for disassembling and assembling the travel motor of a 325D Material Handler excavator. It lists 28 steps for disassembly, removing components like the head, port plate, springs, pistons, and seals. It then lists 24 steps for assembly, reinstalling these components in reverse order and noting to clean all parts, replace seals and gaskets, and apply thread lock compound as needed.
Caterpillar cat 390 f excavator (prefix feh) service repair manual (feh00001 ...fjkskedmme
The document provides instructions for disassembling and assembling the travel motor of a 390F excavator. It describes 40 steps to disassemble the various components of the travel motor including removing the head, relief valves, spools, pistons, plates, seals and bearings. It then describes 36 steps for reassembling the components in reverse order, making sure to align marks and reinstall parts in their original locations. Precautions are provided regarding spring loaded components.
Caterpillar cat 315 c excavator (prefix ake) service repair manual (ake00001 ...fjsekdmmeed
The document provides instructions for disassembling and assembling the travel motor of a 315C excavator. It lists 28 steps for disassembly, beginning with removing the piston motor and ending by taking apart the shaft assembly. It then lists 25 steps for reassembly in reverse order, starting with pressing the inner race back onto the shaft and ending by installing the port plate. Precautions are provided regarding cleanliness, identification marks, and pressurized springs. Tools required include link brackets, a slide hammer, bearing puller, and molybdenum grease.
Caterpillar cat 325 d excavator (prefix kbe) service repair manual (kbe00001 ...hfjsekekmmd
The document provides instructions for repairing the final drive of excavator models 325D and 325D L. It involves 14 steps including cleaning parts, applying lubricants, installing seals and bearings, adjusting bearing preload, and assembling components like the carrier assembly, planetary gears, and ring gear. Proper torque values and alignment of pins are emphasized throughout the process to ensure correct assembly.
The document provides instructions for disassembling and assembling a travel motor. It is a service repair manual for Caterpillar 330D2 and 330D2 L excavators. The disassembly procedure involves removing 28 different parts from the travel motor in 27 steps. The assembly procedure involves installing the parts in the reverse order over 23 steps. Precise alignment and cleanliness of parts is emphasized to ensure proper function.
Caterpillar cat 328 d lcr excavator (prefix rmx) service repair manual (rmx00...fjsekdmmeed
This document provides instructions for disassembling and assembling the swing drive of a 328D LCR excavator. It describes in detail how to disassemble the various components of the swing drive including removing the carrier assembly, planetary gears, ring gear, and pinion shaft. It then describes the assembly process for these components in reverse order, providing illustrations and notes on cleaning, lubricating, and installing components like bearings, seals, and retaining rings. The overall process involves using various tools to carefully remove and reinstall over 15 main components of the swing drive.
Caterpillar Cat 326F L Excavator (Prefix WGL) Service Repair Manual Instant D...f89siekkmdmm2w
This document provides instructions to disassemble a travel motor. It outlines 28 steps to remove various components of the motor including the head, springs, pistons, bearings, seals and housing. Tools required include an adapter, bolts, nuts, eyebolts, retaining ring pliers, a driver group, bearing puller group and a transmission repair stand. Safety notices are provided to wear protective equipment when removing components under spring pressure.
Caterpillar Cat 326F L Excavator (Prefix WGL) Service Repair Manual Instant D...f8uejkdkdmm3e
This document provides instructions to disassemble a travel motor. It outlines 28 steps to remove various components of the motor including the head, springs, pistons, bearings, seals and housing. Tools required include an adapter, bolts, nuts, eyebolts, retaining ring pliers, a driver group, bearing puller group and a transmission repair stand. Safety notices are provided to wear protective equipment when removing components under spring pressure.
Caterpillar Cat 326F L Excavator (Prefix WGL) Service Repair Manual Instant D...gongfuao7509
This document provides instructions to disassemble a travel motor. It begins by having the technician remove the travel motor and attach it to assembly tools. It then lists 28 steps to fully disassemble the travel motor by removing components like caps, springs, seals, plates and housing assemblies. Safety notices are included throughout to warn of potential injury from released spring forces.
Caterpillar Cat 326F L Excavator (Prefix WGL) Service Repair Manual Instant D...shibi1322
This document provides instructions to disassemble a travel motor. It outlines 28 steps to remove various components of the motor including the head, springs, pistons, bearings, seals and housing. Tools required include an adapter, bolts, nuts, eyebolts, retaining ring pliers, a driver group, bearing puller group and a transmission repair stand. Safety notices are provided to wear protective equipment when removing components under spring pressure.
Caterpillar cat 319 d l excavator (prefix wbj) service repair manual (wbj0000...fjkskedmme
The document provides instructions for disassembling and assembling a final drive component of a 319D LN excavator. It includes 33 steps for disassembly, removing components like the cover, carrier assembly, ring gears, and seals. The assembly section has 13 steps, including preloading the bearings to determine the correct shim thickness, installing seals and pins, and attaching the main housing to the motor housing. Precise cleaning and use of replacement parts is emphasized throughout.
Caterpillar cat 330 d excavator (prefix nbd) service repair manual (nbd00001 ...hhjsekmdmm
The document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive. Key components that are disassembled include the drive housing, planetary gear assemblies, ring gear, carrier assemblies, and individual planet gears. Tools required include link brackets and forcing bolts to remove components. Safety notes are provided to clean parts before disassembly and have two people assist with heavier components.
Caterpillar cat 320 d rr excavator (prefix yds) service repair manual (yds000...fjkskedmme
This document provides instructions for disassembling and assembling the travel motor on a 320D RR excavator. It lists the required tools and parts. The disassembly procedure involves removing 25 components from the travel motor in a specific sequence. The assembly procedure instructs putting the travel motor back together in the reverse order and provides important notes to ensure proper installation.
Caterpillar cat 390 f excavator (prefix hng) service repair manual (hng00001 ...fjskefksemer
This document provides instructions for removing and installing the front gear group of a C18 engine. The removal procedure involves removing 14 bolts, plates, gears and seals. Special care must be taken to mark gear orientations and not turn the crankshaft during removal. The installation procedure describes cleaning components, applying thread lock compound, installing 14 gears, plates and seals in the correct order and orientation, and adjusting backlash between gears. Proper removal and installation is important to avoid engine damage.
Caterpillar cat 950 f wheel loader (prefix 4dj) service repair manual (4dj000...ifkkdmdmdm
This document provides step-by-step instructions for disassembling the transmission of a 950F Wheel Loader model. It lists 79 steps to remove various transmission components including the torque converter, transmission control valve, carrier assemblies, planetary gears, clutches, seals, and housing components. Detailed diagrams accompany each step to illustrate the proper procedure and required tooling.
Caterpillar cat 325 f excavator (prefix ndj) service repair manual (ndj00001 ...hfjsekekmmd
The document provides instructions for disassembling and assembling the travel motor of a 325F excavator. It includes 30 steps for disassembly, removing components like the spring, spool, relief valve, head assembly, housing assembly and more. The 31 steps for assembly include installing seals, springs, pistons, cam plate, barrel assembly and ensuring proper alignment of components. Special tools and precautions are noted to properly release spring forces and prevent damage during assembly.
Caterpillar cat 374 d l excavator (prefix pax) service repair manual (pax0000...fjkskedmme
The document provides instructions for disassembling and assembling components of a 374D L excavator travel motor and final drive system. It describes 17 steps to disassemble the final drive, including removing the final drive cover, ring gear, sun gears, carrier assemblies, planetary gears and shafts. Tools required include a transmission repair stand, link brackets, hydraulic wrench, hex bit socket and forcing bolts. Marks must be made to indicate original part locations for reassembly.
Caterpillar cat 325 d mobile hyd power unit (prefix c3n) service repair manua...fikkskmmdm
The document provides instructions for removing and installing an alternator from an engine that is still installed in a machine. The procedure involves:
1. Disconnecting the positive battery terminal to prevent wiring damage.
2. Removing the belt from the alternator pulley.
3. Removing bolts securing the alternator and removing it from the engine.
4. Installing the new alternator using the securing bolts and adjusting the belt tension.
Caterpillar cat 320 d lrr excavator (prefix fxk) service repair manual (fxk00...fjkskedmme
This document provides instructions for removing and installing the crankshaft and crankshaft gear on Caterpillar 3064 and 3066 engines. It outlines the required tools and step-by-step procedures for removing components like the main bearings, connecting rod caps, and crankshaft. Instructions are provided for checking clearances and installing each part in reverse order. Proper cleaning and lubrication of parts is emphasized to prevent premature wear.
Caterpillar cat 318 f l excavator (prefix hcp) service repair manual (hcp0000...fjkskedmme
This document provides instructions for disassembling and assembling the travel motor of a 318F L Excavator. It lists the required tools and presents 31 steps for disassembly, including removing components like the springs, spools, caps, and head assembly. It then lists 29 steps for assembly, instructing technicians to install these components in reverse order. Safety warnings are provided throughout to avoid injury from spring forces. The document is intended to guide maintenance technicians through a complete travel motor overhaul.
Caterpillar cat 329 e excavator (prefix k2l) service repair manual (k2l00001 ...fikkskmmdm
This document provides instructions for disassembling and assembling the travel motor of a 329E Mobile Hydraulic Power Unit. It lists 28 steps for disassembly, removing components like the head, brake piston, rotating assembly, and seals. It then lists 23 steps for assembly, reinstalling those components in reverse order while noting proper lubrication and alignment of parts. Tools required are also listed.
The document provides instructions for disassembling and assembling the travel motor of a 320 GC excavator. It lists the required tools and parts. The disassembly process involves removing plugs and seals from the motor housing. Springs must be released carefully due to risk of injury. The brake piston is then unseated using air pressure before internal components of the motor can be accessed and replaced. The assembly procedure reverses the disassembly steps.
Caterpillar cat 325 d mh excavator (prefix rjk) service repair manual (rjk000...fjsekkdmme
This document provides instructions for disassembling and assembling the travel motor of a 325D Material Handler excavator. It lists 28 steps for disassembly, removing components like the head, port plate, springs, pistons, and seals. It then lists 24 steps for assembly, reinstalling these components in reverse order and noting to clean all parts, replace seals and gaskets, and apply thread lock compound as needed.
Caterpillar cat 390 f excavator (prefix feh) service repair manual (feh00001 ...fjkskedmme
The document provides instructions for disassembling and assembling the travel motor of a 390F excavator. It describes 40 steps to disassemble the various components of the travel motor including removing the head, relief valves, spools, pistons, plates, seals and bearings. It then describes 36 steps for reassembling the components in reverse order, making sure to align marks and reinstall parts in their original locations. Precautions are provided regarding spring loaded components.
Caterpillar cat 315 c excavator (prefix ake) service repair manual (ake00001 ...fjsekdmmeed
The document provides instructions for disassembling and assembling the travel motor of a 315C excavator. It lists 28 steps for disassembly, beginning with removing the piston motor and ending by taking apart the shaft assembly. It then lists 25 steps for reassembly in reverse order, starting with pressing the inner race back onto the shaft and ending by installing the port plate. Precautions are provided regarding cleanliness, identification marks, and pressurized springs. Tools required include link brackets, a slide hammer, bearing puller, and molybdenum grease.
Caterpillar cat 325 d excavator (prefix kbe) service repair manual (kbe00001 ...hfjsekekmmd
The document provides instructions for repairing the final drive of excavator models 325D and 325D L. It involves 14 steps including cleaning parts, applying lubricants, installing seals and bearings, adjusting bearing preload, and assembling components like the carrier assembly, planetary gears, and ring gear. Proper torque values and alignment of pins are emphasized throughout the process to ensure correct assembly.
The document provides instructions for disassembling and assembling a travel motor. It is a service repair manual for Caterpillar 330D2 and 330D2 L excavators. The disassembly procedure involves removing 28 different parts from the travel motor in 27 steps. The assembly procedure involves installing the parts in the reverse order over 23 steps. Precise alignment and cleanliness of parts is emphasized to ensure proper function.
Caterpillar cat 328 d lcr excavator (prefix rmx) service repair manual (rmx00...fjsekdmmeed
This document provides instructions for disassembling and assembling the swing drive of a 328D LCR excavator. It describes in detail how to disassemble the various components of the swing drive including removing the carrier assembly, planetary gears, ring gear, and pinion shaft. It then describes the assembly process for these components in reverse order, providing illustrations and notes on cleaning, lubricating, and installing components like bearings, seals, and retaining rings. The overall process involves using various tools to carefully remove and reinstall over 15 main components of the swing drive.
Caterpillar Cat 326F L Excavator (Prefix WGL) Service Repair Manual Instant D...f89siekkmdmm2w
This document provides instructions to disassemble a travel motor. It outlines 28 steps to remove various components of the motor including the head, springs, pistons, bearings, seals and housing. Tools required include an adapter, bolts, nuts, eyebolts, retaining ring pliers, a driver group, bearing puller group and a transmission repair stand. Safety notices are provided to wear protective equipment when removing components under spring pressure.
Caterpillar Cat 326F L Excavator (Prefix WGL) Service Repair Manual Instant D...f8uejkdkdmm3e
This document provides instructions to disassemble a travel motor. It outlines 28 steps to remove various components of the motor including the head, springs, pistons, bearings, seals and housing. Tools required include an adapter, bolts, nuts, eyebolts, retaining ring pliers, a driver group, bearing puller group and a transmission repair stand. Safety notices are provided to wear protective equipment when removing components under spring pressure.
Caterpillar Cat 326F L Excavator (Prefix WGL) Service Repair Manual Instant D...gongfuao7509
This document provides instructions to disassemble a travel motor. It begins by having the technician remove the travel motor and attach it to assembly tools. It then lists 28 steps to fully disassemble the travel motor by removing components like caps, springs, seals, plates and housing assemblies. Safety notices are included throughout to warn of potential injury from released spring forces.
Caterpillar Cat 326F L Excavator (Prefix WGL) Service Repair Manual Instant D...shibi1322
This document provides instructions to disassemble a travel motor. It outlines 28 steps to remove various components of the motor including the head, springs, pistons, bearings, seals and housing. Tools required include an adapter, bolts, nuts, eyebolts, retaining ring pliers, a driver group, bearing puller group and a transmission repair stand. Safety notices are provided to wear protective equipment when removing components under spring pressure.
Caterpillar Cat 326F L Excavator (Prefix WGL) Service Repair Manual Instant D...8foskkdjdkdm3e
This document provides instructions to disassemble a travel motor. It begins by having the technician remove the travel motor and attach it to assembly tools. It then lists each component that needs to be removed from the travel motor in 28 sequential steps, providing pictures to illustrate where each component is located. Safety notices are included throughout to warn technicians of potential injury from released springs or falling heavy parts.
Caterpillar Cat 326F L Excavator (Prefix WGL) Service Repair Manual Instant D...yin9niaojiao
This document provides instructions to disassemble a travel motor. It outlines 28 steps to remove various components of the motor including the head, springs, pistons, bearings, seals and housing. Tools required include an adapter, bolts, nuts, eyebolts, retaining ring pliers, a driver group, bearing puller group and a transmission repair stand. Safety notices are provided to wear protective equipment when removing components under spring pressure.
Caterpillar cat 326 d2 l excavator (prefix lcw) service repair manual (lcw000...fjsjekkmdmme
The document provides instructions for disassembling the travel motor of an excavator model 326D2. It involves 28 steps including removing the head, brake piston, plates and discs, seals, bearings, and other components. Various tools are required including an adapter, bolts, retaining ring pliers, and a bearing puller group. Safety precautions are provided regarding spring forces.
The document provides instructions for disassembling the travel motor of an excavator model 326D2. It involves 28 steps including removing the head, brake piston, plates and discs, seals, bearings, and other components. Various tools are required including an adapter, bolts, retaining ring pliers, and a bearing puller group. Safety precautions are provided regarding spring forces.
Caterpillar cat 326 d2 l excavator (prefix lcw) service repair manual (lcw000...fjjskdmnenemm
This document provides instructions for disassembling the travel motor of an excavator model 326D2. The 28 step procedure includes removing components like the head assembly, housing assembly, brake piston, springs, seals, and other internal parts. Various tools are required to dismantle the travel motor safely and in the correct order, with notes to take care when removing parts under spring pressure. The detailed disassembly process is described through illustrations and text to clearly explain each step.
This document provides instructions for disassembling the travel motor of an excavator model 326D2. The 28 step procedure includes removing components like the head assembly, housing assembly, brake piston, springs, seals, and other internal parts. Various tools are required to remove retaining rings, pins, and other fasteners. Safety precautions are provided to avoid injury from released spring forces during disassembly.
Caterpillar Cat 326D2 L Excavator (Prefix LCW) Service Repair Manual (LCW0000...km7seydwuhdw
This document provides instructions for disassembling the travel motor of an excavator model 326D2. The 28 step procedure includes removing components like the head assembly, housing assembly, brake piston, springs, seals, and other internal parts. Various tools are required to remove retaining rings, pins, and push components like the brake piston out of place. Safety precautions are provided throughout to warn of spring forces, pressurized air, and weight of parts being removed.
Similar to Caterpillar cat 326 f l excavator (prefix xfk) service repair manual (xfk00001 and up) (11)
Caterpillar cat 345 b series ii excavator (prefix dcw) service repair manual ...fujsekfkksemm
This document provides instructions for removing and installing the cylinder head on a 345B Series II Excavator with a 3176 engine. The removal procedure involves removing components like the valve mechanism cover, rocker shaft, and pushrods. Sensors and tubes must be disconnected from the cylinder head before removing bolts and lifting the head off. For installation, the mating surfaces are cleaned and the correct gasket is installed before lowering the head onto the cylinder block and installing bolts.
Caterpillar cat 345 b series ii excavator (prefix ald) service repair manual ...fujsekfkksemm
This document provides instructions for installing a cylinder head on a 3176C engine. It involves cleaning surfaces, installing gaskets and seals, lifting the cylinder head into place using guide bolts, and tightening head bolts in a specific sequence to the correct torque specifications. Sensors and wiring are then reconnected, coolant is added to the system, and remaining components like the rocker shaft and pushrods are reinstalled to complete the job.
Caterpillar cat 345 b series ii excavator (prefix ccc) service repair manual ...fujsekfkksemm
This document provides instructions for removing and installing the cylinder head on a 345B Series II Excavator with a 3176C engine. The removal procedure involves removing various components like sensors, tubes, and manifolds. The cylinder head bolts are then removed and the head lifted off using a suitable lifting device. For installation, the mating surfaces are cleaned and new gaskets installed before positioning the cylinder head on the block and installing the bolts.
Caterpillar cat 345 c excavator (prefix dhp) service repair manual (dhp00001 ...fujsekfkksemm
The document provides instructions for disassembling and assembling the travel motor of a 345C excavator. It lists 31 steps to disassemble the travel motor by removing components like the head, plates, seals, pins, and piston assemblies. It notes to mark parts for reinstallation and clean components to prevent contamination. Reassembly follows the reverse order of disassembly.
Caterpillar cat 345 c excavator (prefix spc) service repair manual (spc00001 ...fujsekfkksemm
The document provides instructions for disassembling and assembling the travel motor of a 345C L EXCAVATOR. It lists 31 steps to disassemble the various components of the travel motor using different tools. These components include the head, plates, seals, pins, brake piston, disks, rotating group, shaft assembly, barrels, seals, and more. It notes to mark parts for reinstallation and clean components thoroughly. The assembly procedure is listed but not described in detail.
Caterpillar cat 345 c excavator (prefix wde) service repair manual (wde00001 ...fujsekfkksemm
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. The disassembly procedure involves removing 30 parts from the final drive assembly using various tools. The assembly procedure is the reverse of the disassembly process and includes applying thread lock compound and gasket sealant to specific joints.
Caterpillar cat 345 c hydraulic excavator (prefix tdg) service repair manual ...fujsekfkksemm
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, seals, pistons, and housing pieces. It then lists 13 steps for assembly, reinstalling these components in reverse order and noting to clean all parts, apply lubricant, and replace all seals and gaskets. Precise measurements and tooling are required to properly assemble the travel motor.
Caterpillar cat 345 c l excavator (prefix scn) service repair manual (scn0000...fujsekfkksemm
This document provides step-by-step instructions for disassembling and assembling the final drive of a 345C L excavator. It details removing over 30 individual components in 28 steps, including the final drive cover, carrier assemblies, ring gear, and sprocket housing. Reassembly follows the reverse order, with notes to reinstall parts in their original positions and orientations. Required tools include transmission stands, eyebolts, retaining ring pliers, and seal installers.
Caterpillar cat 345 c l excavator (prefix s5m) service repair manual (s5m0000...fujsekfkksemm
This document provides step-by-step instructions for disassembling and assembling the final drive components of a 345C L Excavator. The disassembly process involves removing over 20 individual parts from the final drive housing including gears, shafts, bearings, seals and other components. Proper identification of part locations and orientations is emphasized for reassembly. Required tools include lifting devices, retaining ring pliers, eyebolts and other specialized tools.
Caterpillar cat 345 c l excavator (prefix spc) service repair manual (spc0000...fujsekfkksemm
The document provides instructions for disassembling and assembling the travel motor of a 345C L EXCAVATOR. It lists 31 steps to disassemble the various components of the travel motor including removing the head, brake piston, disks, rotating group, piston assemblies, seals and more. Detailed illustrations are provided to identify each part. When assembling, the instructions note to clean all parts and reinstall components in their original locations and orientations. Precautions are outlined to contain fluids, avoid damage, and prevent contamination.
Caterpillar cat 345 c l excavator (prefix wde) service repair manual (wde0000...fujsekfkksemm
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. The disassembly procedure involves removing 30 parts from the final drive assembly using various tools. The assembly procedure is the reverse of the disassembly steps and includes applying thread lock compound and gasket sealant to specific joints.
Caterpillar cat 345 b l excavator (prefix 9cw) service repair manual (9cw0000...fujsekfkksemm
This document provides instructions for removing and installing the rocker shaft, pushrods, and cylinder head on a Caterpillar 345B L excavator engine. The removal procedure involves removing covers, shafts, rods, sensors and manifolds. The cylinder head is then lifted off. The installation procedure specifies cleaning components, installing gaskets and seals, and torquing bolts to specifications when reassembling the cylinder head and related parts.
Caterpillar cat 345 b l excavator (prefix 8rw) service repair manual (8rw0000...fujsekfkksemm
This document provides instructions for installing a cylinder head on a 345B L EXCAVATOR engine. It describes cleaning and inspecting the cylinder head and block mating surfaces. The correct cylinder head gasket must be installed, along with new O-rings. The cylinder head is placed on guide bolts and bolts are tightened in a specific sequence to the correct torques. Sensors and lines are then reconnected to the cylinder head before installing the water outlet manifold.
Caterpillar cat 345 b excavator (prefix ayr) service repair manual (ayr00001 ...fujsekfkksemm
This document provides instructions for disassembling and assembling the final drive components of an excavator model 345B. It describes removing 27 components including the travel motor, final drive, carrier assemblies, ring gear, and sprocket housing. Detailed illustrations and notes are provided to aid in correctly identifying parts and maintaining proper orientation during reassembly. Required tools include various link brackets, retaining ring pliers, seal installer, anti-seize compound, grease, thread lock, gasket sealant and a transmission stand.
Caterpillar cat 345 b excavator (prefix amn) service repair manual (amn00001 ...fujsekfkksemm
The document provides instructions for disassembling and assembling the travel motor of an excavator model 345B. It lists 31 steps to disassemble the travel motor by removing components like the head, plates, seals, pistons, bearings and housing. It also lists tools required for the job and safety notices about keeping parts clean and containing fluids.
Caterpillar cat 345 b excavator (prefix amj) service repair manual (amj00001 ...fujsekfkksemm
The document provides assembly instructions for a travel motor in 3 steps:
1. It describes preparing the travel motor components and inserting keys, seals, pistons, plates and spacers into the motor body.
2. It explains assembling the barrel, installing the shaft and bearings, and inserting friction disks and separator plates.
3. It outlines attaching the head, installing valves, plugs and seals to complete the assembly. Precise measurements and torque specifications are listed to ensure correct assembly.
Caterpillar cat 345 b excavator (prefix amd) service repair manual (amd00001 ...fujsekfkksemm
The document provides assembly instructions for a travel motor in 3 steps:
1) It describes preparing the travel motor body by installing seals, pistons, and spacers.
2) It explains assembling the barrel, installing the shaft and bearings, and inserting friction disks and plates.
3) It outlines attaching the head, installing valves and plugs, and filling the travel motor with oil before operation.
Caterpillar cat 345 b excavator (prefix 8kw) service repair manual (8kw00001 ...fujsekfkksemm
This document provides instructions for removing and installing the rocker shaft, pushrods, cylinder head, and related components on a 345B Excavator engine. The removal process involves removing covers, shafts, rods, sensors, tubes, and manifolds before lifting the cylinder head off. The installation process specifies cleaning, inspecting, and lubricating components before lowering the cylinder head back onto the engine and reinstalling related parts in reverse order of removal. Tools and torque specifications are listed for select steps.
Caterpillar cat 345 b excavator (prefix 6mw) service repair manual (6mw00001 ...fujsekfkksemm
The document provides instructions for disassembling and assembling the travel motor of a 345B Excavator. It lists 32 steps for disassembly, including removing covers, springs, seals, gears, and housing components. It then lists 15 steps for assembly, reversing the disassembly process and including inspecting parts and ensuring cleanliness to prevent contamination. The overall document provides detailed technical instructions for servicing the excavator's travel motor.
Caterpillar cat 340 f excavator (prefix sgh) service repair manual (sgh00001 ...fujsekfkksemm
The document provides disassembly instructions for a swing drive on a 340F excavator model. It begins by having the technician remove the swing drive and mark parts for reassembly. Several internal components of the swing drive are then removed, including planetary gears, shafts, rings, and housings. Precision tools are required and technicians should be careful due to the weights of parts removed. Cleanliness is emphasized to prevent contamination of hydraulic systems during repair.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 326F L EXCAVATOR XFK
Configuration: 326F L & 326F LN Excavators XFK00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
326F, 329F and 330F Excavators Machine Systems
Media Number -UENR3313-07 Publication Date -01/09/2015 Date Updated -12/09/2018
i05435976
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- Threaded RodM12 x 1.75 by 250 mm (10 inch) 1
B
8T-0651 Bolt 1
8T-4167 Hard Washer 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
Start By:
a. Remove the travel motor.
1/10
326F L & 326F LN Excavators XFK00001-UP (MACHINE) POWERED BY C7.1 En...
2020/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1. Thoroughly clean the outside of the travel motor prior to disassembly.
2. Fasten the travel motor in Tooling (A) in a vertical position. The weight of the travel motor
is approximately 60 kg (132 lb).
3. Put an alignment mark across the head and the body of the travel motor for assembly
purposes. The head must be reinstalled in the original position on the body of the travel
motor.
Illustration 1 g00887295
Note: During the removal of head (2) from the travel motor, be careful not to damage the
mating surfaces of the components.
Spring force can cause personal injury or death.
Do not repair until you have read the Operation and Maintenance
Manual.
2/10
326F L & 326F LN Excavators XFK00001-UP (MACHINE) POWERED BY C7.1 En...
2020/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 4. Remove bolts (1).
5. Remove head (2) from the body of the travel motor.
Illustration 2 g00887302
6. Remove O-ring seal (3), port plate (4), and bearing (5).
Illustration 3 g00887311
7. Remove O-ring seals (6). Remove springs (7).
Illustration 4 g00887331
3/10
326F L & 326F LN Excavators XFK00001-UP (MACHINE) POWERED BY C7.1 En...
2020/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 5 g00890074
A typical example of the use of Tooling (B).
8. Place a shop towel over brake piston (8). Retain brake piston (8) with Tooling (B). Apply
approximately 525 kPa (75 psi) of shop air pressure to brake release Port (Y). Make sure
that the shop air pressure is free of water. Brake piston (8) will move up the piston guide,
and out of the piston guide. Remove brake piston (8) from the body of the travel motor.
Illustration 6 g00887336
9. Remove seal (9) and backup ring (10) from the brake piston.
10. Remove seal (11) and backup ring (12) from the brake piston.
4/10
326F L & 326F LN Excavators XFK00001-UP (MACHINE) POWERED BY C7.1 En...
2020/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 7 g00887355
11. Remove plates (13) and friction discs (14).
Illustration 8 g00887401
Illustration 9 g00887405
12. Install Tooling (C) into shaft (15). Use a prybar to remove the rotating assembly (16) from
the housing.
13. Remove Tooling (C) from shaft (15).
Illustration 10 g00887424
5/10
326F L & 326F LN Excavators XFK00001-UP (MACHINE) POWERED BY C7.1 En...
2020/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 14. Remove shaft (15) from the rotating assembly .
Illustration 11 g00887426
15. Use Tooling (D) in order to remove retaining ring (17) from shaft (15).
Illustration 12 g00887445
Illustration 13 g00887463
16. Install shaft (15) into a suitable press. Remove bearing race (18) from the shaft.
17. Rotate shaft (15). Install shaft (15) into a suitable press. Install Tooling (E). Remove bearing
race (19) from shaft (15).
6/10
326F L & 326F LN Excavators XFK00001-UP (MACHINE) POWERED BY C7.1 En...
2020/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 14 g00887501
18. Remove cam plate (20) from barrel assembly (21).
Illustration 15 g00887520
19. Remove piston assemblies and retainer plate (22) from barrel assembly (21).
Note: Place marks on the pistons and the barrel assembly. The pistons must be returned to
the original position.
Illustration 16 g00887558
7/10
326F L & 326F LN Excavators XFK00001-UP (MACHINE) POWERED BY C7.1 En...
2020/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 20. Remove ball (23) and springs (24).
Illustration 17 g03431370
21. Remove bearing (25).
22. Remove keys (26) and locating pins (not shown) from the body of the travel motor.
Illustration 18 g00887589
23. Rotate the housing. Use Tooling (F) in order to remove retaining ring (27).
24. Remove lip seal (28).
8/10
326F L & 326F LN Excavators XFK00001-UP (MACHINE) POWERED BY C7.1 En...
2020/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 19 g00887619
25. Remove bolts (29) and cover (30).
Illustration 20 g00887729
26. Remove seal (31) and backup ring (32).
Illustration 21 g00887754
27. Remove piston actuator (33) and seal (34).
Illustration 22 g00887762
9/10
326F L & 326F LN Excavators XFK00001-UP (MACHINE) POWERED BY C7.1 En...
2020/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. 28. Remove O-ring seal (35) from the housing of the travel motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 13 10:19:51 UTC+0800 2020
10/10
326F L & 326F LN Excavators XFK00001-UP (MACHINE) POWERED BY C7.1 ...
2020/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 326F L EXCAVATOR XFK
Configuration: 326F L & 326F LN Excavators XFK00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
326F, 329F and 330F Excavators Machine Systems
Media Number -UENR3313-07 Publication Date -01/09/2015 Date Updated -12/09/2018
i07505849
Travel Motor - Disassemble
SMCS - 4351-015
S/N - B321-UP
S/N - EBK1-UP
S/N - ERL1-UP
S/N - FBR1-UP
S/N - GGJ1-UP
S/N - GHT1-UP
S/N - HBT1-UP
S/N - HCA1-UP
S/N - HCJ1-UP
S/N - HCK1-UP
S/N - JFR1-UP
S/N - JHF1-UP
S/N - KFA1-UP
S/N - LBN1-UP
S/N - LCG1-UP
S/N - MBX1-UP
1/14
326F L & 326F LN Excavators XFK00001-UP (MACHINE) POWERED BY C7.1 En...
2020/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. S/N - RCN1-UP
S/N - TMR1-UP
S/N - TPG1-UP
S/N - WBA1-UP
S/N - WGL1-UP
S/N - XFK1-UP
S/N - YHA1-UP
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1P-2420 Transmission Repair Stand 1
FT-0957 Positioning Gp 4
B
- M16x2 Threaded Rod 3
8T-1757 Nut 6
9X-8268 Washer 6
C 421-5662 Lifting Eye Assembly 1
D 421-5663 Lifting Eye Assembly 2
E
1U-9895 Crossblock 1
3H-0465 Push-Puller Plate 2
8T-0298 Bolt 2
Start By:
a. Remove the travel motor.
2/14
326F L & 326F LN Excavators XFK00001-UP (MACHINE) POWERED BY C7.1 En...
2020/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 1 g06341880
1. Attach the travel motor to Tooling (A) and (B). The weight of the travel motor is
approximately 70 kg (154 lb).
2. Remove plugs (1) and the O-ring seals.
Illustration 2 g06344110
3. Remove plug (2) and the O-ring seal. Repeat for the opposite side.
Illustration 3 g06341912
3/14
326F L & 326F LN Excavators XFK00001-UP (MACHINE) POWERED BY C7.1 En...
2020/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
4. Remove plug (2A) and the O-ring seal. Repeat for the opposite side.
Illustration 4 g06341915
5. Remove spring (3).
Illustration 5 g06341917
6. Remove spool (4).
4/14
326F L & 326F LN Excavators XFK00001-UP (MACHINE) POWERED BY C7.1 En...
2020/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 6 g06341942
Illustration 7 g06342000
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
7. Remove bolts (5) and cap (6). Repeat for the opposite side.
8. Remove O-ring seal (10) from cap (6). Remove guide (9), spring (8), and washer (7) from
the head assembly. Repeat for the opposite side.
5/14
326F L & 326F LN Excavators XFK00001-UP (MACHINE) POWERED BY C7.1 En...
2020/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 8 g06342005
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
9. Remove plug (11), O-ring seal (12), spring (13), and ball (14) from cap (6). Repeat for the
other cap.
Illustration 9 g06342009
10. Remove spool (15).
6/14
326F L & 326F LN Excavators XFK00001-UP (MACHINE) POWERED BY C7.1 En...
2020/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 10 g06343314
Illustration 11 g06343315
11. Remove relief valve (16). Remove O-ring seal (17) from relief valve (16).
12. Repeat for the opposite side.
Illustration 12 g06343359
7/14
326F L & 326F LN Excavators XFK00001-UP (MACHINE) POWERED BY C7.1 En...
2020/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
13. Remove the nuts of Tooling (B). Remove bolts (19) from head assembly (18).
Illustration 13 g06343366
14. Use Tooling (C) and a suitable lifting device to remove head assembly (18). The weight of
head assembly (18) is approximately 21 kg (47 lb).
Illustration 14 g06343374
15. Remove control plate (20) and bearing (21) from head assembly (18).
8/14
326F L & 326F LN Excavators XFK00001-UP (MACHINE) POWERED BY C7.1 En...
2020/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 15 g06343381
16. Remove pins (22) and springs (23).
17. Remove O-ring seals (24) and (25).
Illustration 16 g06343383
18. Use Tooling (D) and a suitable lifting device to remove housing assembly (26) from
Tooling (A) and place on a suitable bench.
Illustration 17 g06343417
9/14
326F L & 326F LN Excavators XFK00001-UP (MACHINE) POWERED BY C7.1 En...
2020/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. To avoid personal injury, always wear eye and face protection when
using pressurized air.
19. Attach Tooling (E) to housing (26). Use air pressure to unseat brake piston (27). Remove
Tooling (E) and brake piston (27).
Illustration 18 g06343437
20. Remove back up rings (28) and O-ring seals (29) from brake piston (27).
Illustration 19 g06343462
21. Remove brake piston guide (30).
10/14
326F L & 326F LN Excavators XFK00001-UP (MACHINE) POWERED BY C7.1 ...
2020/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
23. Illustration 20 g06343464
22. Remove O-ring seal (31) from brake piston guide (30).
Illustration 21 g06343466
Illustration 22 g06343469
Note: Note the orientation of friction discs (32) and plates (33) for assembly purposes.
23. Remove friction discs (32) and plates (33).
11/14
326F L & 326F LN Excavators XFK00001-UP (MACHINE) POWERED BY C7.1 ...
2020/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 23 g06343638
24. Remove rotating group (34) from housing (26).
Illustration 24 g06343777
25. Remove pistons (35) and retainer (36) from barrel (37).
Illustration 25 g06343783
26. Remove hold down ball (38) and springs (39) from barrel (37).
12/14
326F L & 326F LN Excavators XFK00001-UP (MACHINE) POWERED BY C7.1 ...
2020/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...