The document provides instructions for checking and installing crankshaft components in a 3126B engine, including:
1. Removing the crankshaft rear seal and checking clearance of the crankshaft wear sleeve.
2. Installing the crankshaft rear seal and wear sleeve using a series of tools to properly set them in place.
3. Installing the crankshaft by cleaning surfaces, applying oil, and tightening main bearing caps to the specified torque.
4. Removing and installing the crankshaft gear using pullers and ensuring the woodruff key is in place.
5. Checking bearing clearance using a dial indicator.
Caterpillar cat 325 c l excavator (prefix jlc) service repair manual (jlc0000...fjskeazqkkdmme
The document provides instructions for checking crankshaft bearing clearance on a Caterpillar 3126B engine. It describes using plastic gauge tools to measure clearance between the crankshaft journal and bearing. The procedure involves inserting the gauge into the bearing cap or on the journal, torquing the cap to spec, and measuring the gauge width to obtain clearance. It notes that the manufacturer does not recommend checking actual clearances due to risk of damage or inaccurate results, but provides the plastic gauge method if a technician wishes to measure clearances. Clearances should be within specifications in the manual.
Caterpillar cat 325 c excavator (prefix jlc) service repair manual (jlc00001 ...ifosodkmsme
The document provides instructions for checking crankshaft bearing clearance on a Caterpillar 3126B engine. It describes using plastic gauge tools to measure clearance between the crankshaft journal and bearing. The procedure involves inserting the gauge into the bearing cap or on the journal, torquing the cap to spec, and measuring the gauge width to obtain clearance. It notes that the manufacturer does not recommend checking actual clearances due to risk of damage or inaccurate results, but provides the plastic gauge method if a technician wishes to measure clearances. Clearances should be within specifications per the engine model.
Caterpillar cat 325 c l excavator (prefix jlc) service repair manual (jlc0000...fjkskedmme
The document provides instructions for checking and servicing components of a Caterpillar 3126B engine, including:
1. Removing and installing a crankshaft rear wear sleeve, which requires using specialty tools to distort and remove the old sleeve before pressing in a new one.
2. Installing the crankshaft, which involves cleaning surfaces, applying oil, and torquing bolts to specifications while checking end play.
3. Removing and installing the crankshaft gear, which requires heating the gear and using a puller and hydraulic press for removal and installation.
4. Checking bearing clearance using a dial indicator in accordance with specifications.
Caterpillar cat 325 c excavator (prefix jlc) service repair manual (jlc00001 ...fjskekdmjekm
The document provides instructions for checking and servicing components of a Caterpillar 3126B engine, including:
1. Removing and installing a crankshaft rear wear sleeve, which requires using specialty tools to distort and remove the old sleeve before pressing in a new one.
2. Installing the crankshaft, which involves cleaning surfaces, applying oil, and torquing bolts to specifications while checking end play.
3. Removing and installing the crankshaft gear, which requires heating the gear and using a puller and hydraulic press for removal and installation.
4. Checking bearing clearance using a dial indicator to ensure measurements are within the specified range.
Caterpillar Cat 325C L Excavator (Prefix JLC) Service Repair Manual (JLC00001...shudun96087
The document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator, including:
1. Removing the crankshaft rear seal and crankshaft wear sleeve using special tools to distort the sleeve and loosen it from the crankshaft.
2. Installing the new crankshaft rear seal and wear sleeve using a multi-piece installer tool and nut to fully seat the components.
3. Removing the crankshaft gear using a hydraulic puller tool, and installing it by heating the gear and pressing it onto the crankshaft keyway.
The document contains detailed step-by-step instructions, illustrations, and caut
The document provides instructions for removing and installing a crankshaft wear sleeve on a 325C excavator. It describes using special tools to distort the sleeve until it is loose, then removing it from the crankshaft. For installation, a seal locator tool and sleeve ring are used along with a seal installer and nut to press the sleeve and new seal into place on the crankshaft. Technicians are advised to keep all parts clean and check that the sleeve and seal are properly installed before continuing reassembly.
Caterpillar Cat 325C L Excavator (Prefix JLC) Service Repair Manual (JLC00001...yfbr995309
The document provides instructions for removing and installing a crankshaft wear sleeve on a 325C excavator. It describes using special tools to distort the sleeve until it is loose, then removing it from the crankshaft. For installation, a seal locator tool and installer tool are used to position the sleeve and seal and drive them onto the crankshaft. The procedure aims to properly install the sleeve and seal while keeping them clean from contaminants.
The document provides instructions for removing and installing a crankshaft wear sleeve on a 325C excavator. It describes using special tools to distort the sleeve until it is loose, then removing it from the crankshaft. For installation, a seal locator tool and sleeve ring are used along with a seal installer and nut to press the sleeve and new seal into place. Technicians are advised to keep all parts clean and check that the sleeve and seal are flush when fully installed.
Caterpillar cat 325 c l excavator (prefix jlc) service repair manual (jlc0000...fjskeazqkkdmme
The document provides instructions for checking crankshaft bearing clearance on a Caterpillar 3126B engine. It describes using plastic gauge tools to measure clearance between the crankshaft journal and bearing. The procedure involves inserting the gauge into the bearing cap or on the journal, torquing the cap to spec, and measuring the gauge width to obtain clearance. It notes that the manufacturer does not recommend checking actual clearances due to risk of damage or inaccurate results, but provides the plastic gauge method if a technician wishes to measure clearances. Clearances should be within specifications in the manual.
Caterpillar cat 325 c excavator (prefix jlc) service repair manual (jlc00001 ...ifosodkmsme
The document provides instructions for checking crankshaft bearing clearance on a Caterpillar 3126B engine. It describes using plastic gauge tools to measure clearance between the crankshaft journal and bearing. The procedure involves inserting the gauge into the bearing cap or on the journal, torquing the cap to spec, and measuring the gauge width to obtain clearance. It notes that the manufacturer does not recommend checking actual clearances due to risk of damage or inaccurate results, but provides the plastic gauge method if a technician wishes to measure clearances. Clearances should be within specifications per the engine model.
Caterpillar cat 325 c l excavator (prefix jlc) service repair manual (jlc0000...fjkskedmme
The document provides instructions for checking and servicing components of a Caterpillar 3126B engine, including:
1. Removing and installing a crankshaft rear wear sleeve, which requires using specialty tools to distort and remove the old sleeve before pressing in a new one.
2. Installing the crankshaft, which involves cleaning surfaces, applying oil, and torquing bolts to specifications while checking end play.
3. Removing and installing the crankshaft gear, which requires heating the gear and using a puller and hydraulic press for removal and installation.
4. Checking bearing clearance using a dial indicator in accordance with specifications.
Caterpillar cat 325 c excavator (prefix jlc) service repair manual (jlc00001 ...fjskekdmjekm
The document provides instructions for checking and servicing components of a Caterpillar 3126B engine, including:
1. Removing and installing a crankshaft rear wear sleeve, which requires using specialty tools to distort and remove the old sleeve before pressing in a new one.
2. Installing the crankshaft, which involves cleaning surfaces, applying oil, and torquing bolts to specifications while checking end play.
3. Removing and installing the crankshaft gear, which requires heating the gear and using a puller and hydraulic press for removal and installation.
4. Checking bearing clearance using a dial indicator to ensure measurements are within the specified range.
Caterpillar Cat 325C L Excavator (Prefix JLC) Service Repair Manual (JLC00001...shudun96087
The document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator, including:
1. Removing the crankshaft rear seal and crankshaft wear sleeve using special tools to distort the sleeve and loosen it from the crankshaft.
2. Installing the new crankshaft rear seal and wear sleeve using a multi-piece installer tool and nut to fully seat the components.
3. Removing the crankshaft gear using a hydraulic puller tool, and installing it by heating the gear and pressing it onto the crankshaft keyway.
The document contains detailed step-by-step instructions, illustrations, and caut
The document provides instructions for removing and installing a crankshaft wear sleeve on a 325C excavator. It describes using special tools to distort the sleeve until it is loose, then removing it from the crankshaft. For installation, a seal locator tool and sleeve ring are used along with a seal installer and nut to press the sleeve and new seal into place on the crankshaft. Technicians are advised to keep all parts clean and check that the sleeve and seal are properly installed before continuing reassembly.
Caterpillar Cat 325C L Excavator (Prefix JLC) Service Repair Manual (JLC00001...yfbr995309
The document provides instructions for removing and installing a crankshaft wear sleeve on a 325C excavator. It describes using special tools to distort the sleeve until it is loose, then removing it from the crankshaft. For installation, a seal locator tool and installer tool are used to position the sleeve and seal and drive them onto the crankshaft. The procedure aims to properly install the sleeve and seal while keeping them clean from contaminants.
The document provides instructions for removing and installing a crankshaft wear sleeve on a 325C excavator. It describes using special tools to distort the sleeve until it is loose, then removing it from the crankshaft. For installation, a seal locator tool and sleeve ring are used along with a seal installer and nut to press the sleeve and new seal into place. Technicians are advised to keep all parts clean and check that the sleeve and seal are flush when fully installed.
The document provides instructions for removing and installing a crankshaft wear sleeve on a 325C excavator. It describes using special tools to distort the sleeve until it is loose, then removing it from the crankshaft. For installation, a seal locator tool and installer tool are used to position the sleeve and seal and drive them onto the crankshaft. The procedure aims to properly install the sleeve and seal while keeping the components clean.
Caterpillar Cat 325C L Excavator (Prefix JLC) Service Repair Manual (JLC00001...kesi7153062
The document provides instructions for removing and installing a crankshaft wear sleeve on a 325C excavator. It describes using special tools to distort the sleeve until it is loose, then removing it from the crankshaft. For installation, a seal locator tool and installer are used to position the sleeve and seal and drive them onto the crankshaft. The document also provides guidelines for checking bearing clearances using plastic gauge tools.
Caterpillar cat 325 c l excavator (prefix amh) service repair manual (amh0000...fjskeazqkkdmme
This document provides instructions for removing and installing various engine components on Caterpillar 325C and 325C L excavators, including:
- Removing and installing the camshaft, camshaft gear, and camshaft bearings. Proper timing of the camshaft is emphasized.
- Removing and installing the engine oil pan. Safety precautions for hot oil and proper fluid containment are outlined.
- The document contains detailed step-by-step instructions, illustrations, and notes on proper component orientation for each procedure. Required tools are listed.
Caterpillar cat 325 c l excavator (prefix amh) service repair manual (amh0000...fjkskedmme
This document provides instructions for removing and installing various engine components on Caterpillar 325C and 325C L excavators, including:
- Removing and installing the camshaft, camshaft gear, and camshaft bearings. Proper timing of the camshaft is emphasized.
- Removing and installing the engine oil pan. Safety precautions for hot oil and proper fluid containment are outlined.
- The document contains detailed step-by-step instructions, illustrations, and notes on proper component orientation for each procedure. Required tools are listed.
Caterpillar cat 325 c excavator (prefix amh) service repair manual (amh00001 ...ifosodkmsme
The document provides instructions for removing and installing various engine components on a Caterpillar 3126B engine, including:
1. Procedures for removing the camshaft, camshaft gear, camshaft bearings, and engine oil pan. Safety notices and required tools are listed.
2. Instructions for installing the camshaft, camshaft gear, camshaft bearings, and engine oil pan. Diagrams illustrate the component locations and installation steps. Torque specifications and seals/gaskets are addressed.
3. Component removal and installation is described in step-by-step format with references to other relevant sections for some components. Proper cleaning, handling and disposal of fluids
Caterpillar cat 325 c excavator (prefix amh) service repair manual (amh00001 ...fjskekdmjekm
This document provides instructions for removing and installing various engine components on Caterpillar 325C and 325C L excavators, including:
- Removing and installing the camshaft, camshaft gear, and camshaft bearings. Proper timing of the camshaft is emphasized.
- Removing and installing the engine oil pan. Safety precautions for hot oil and proper fluid containment are outlined.
- The document contains detailed step-by-step instructions, illustrations, and notes on proper component orientation for each procedure. Required tools are listed.
Caterpillar Cat 325C L Excavator (Prefix CRB) Service Repair Manual (CRB00001...f8usiejdkmdd
The document provides instructions for removing and installing the camshaft on a Caterpillar 3126B engine used in 325C excavators. The summary is:
1) Remove the lifter group and front cover to access the camshaft. Wire the valve lifters away from the camshaft. Remove the camshaft retainer plate and bolts and pull out the camshaft.
2) Install the camshaft, ensuring the timing marks are aligned. Install the camshaft retainer plate and bolts. Reinstall the lifter group and front cover.
3) The document provides step-by-step instructions for removing and installing the camshaft, camshaft
Caterpillar Cat 325C, 325C L and 325C LN Excavator (Prefix CRB) Service Repai...yan77xunhao
The document provides instructions for removing and installing various engine components on a 325C excavator, including:
1. Removing the camshaft by turning the crankshaft to top center, removing retaining bolts, and lifting out the camshaft.
2. Installing the camshaft by carefully inserting it into place while ensuring proper timing marks are aligned.
3. Removing the camshaft gear by first removing the camshaft, wrapping it to protect it, and pressing it out of the gear in a press. Reinstallation involves heating the gear and pressing it onto the camshaft while aligning the key.
The document provides instructions for removing and installing various engine components on a 325C excavator, including:
1. Removing the camshaft by wiring the valve lifters away, removing retaining bolts, and lifting the camshaft out.
2. Installing the camshaft by carefully inserting it into place while ensuring proper timing marks are aligned.
3. Removing the camshaft bearings using a special tool, and installing new bearings by orienting the oil holes and positioning joints.
The document provides instructions for removing and installing the camshaft on a Caterpillar 3126B engine used in 325C excavators. The summary is:
1) Remove the lifter group and front cover to access the camshaft. Wire the valve lifters away from the camshaft. Remove the camshaft retainer plate and bolts, then remove the camshaft.
2) Install the camshaft, ensuring the timing marks are aligned. Install the camshaft retainer plate and bolts. Install the lifter group and front cover.
3) The document provides step-by-step instructions for removing and installing the camshaft, camshaft gear
Caterpillar Cat 336D L Excavator (Prefix M4T) Service Repair Manual Instant D...zan2736ban
The document provides instructions for removing and installing a final drive and travel motor on a 336D L excavator. It lists required tools and gives step-by-step instructions that include disconnecting hoses, removing bolts and covers, lifting out the assembly, and reinstalling it in the reverse order. Safety notices are provided regarding containing fluids, cleaning parts, and relieving hydraulic pressure before disassembly.
Caterpillar Cat 336D L Excavator (Prefix LMG) Service Repair Manual Instant D...zan2736ban
The document provides instructions for assembling a swivel component. It lists required tools including link brackets and vacuum caps. The procedure involves cleaning parts, positioning the swivel joint on a repair stand, and reassembling parts like the outside housing, rotor, seals, bolts and washers in the correct order. Thorough cleaning of parts is important before assembly to prevent contamination.
Caterpillar Cat 336D L Excavator (Prefix L5X) Service Repair Manual Instant D...zan2736ban
This document provides instructions for removing and installing the rear gear group and flywheel on a 336D L excavator. The removal procedure involves using various tools to remove bolts, gears, bushings, bearings, and seals. Installation involves cleaning parts and using tools to carefully lower bearings and gears into place while matching specific dimensions, then reinstalling covers, seals, and bolts. Precautions are given to keep parts clean and properly position oil passages.
Caterpillar Cat 336D L Excavator (Prefix JWR) Service Repair Manual Instant D...zan2736ban
The document provides instructions for removing and installing a final drive and travel motor on a 336D L excavator. It lists required tools and gives step-by-step instructions including disconnecting hoses, removing bolts and covers, lifting out the assembly, and reinstalling it in reverse order. Safety notices are provided regarding containing fluids, releasing pressure from the hydraulic system, and preventing contamination.
Caterpillar Cat 336D L Excavator (Prefix JRX) Service Repair Manual Instant D...zan2736ban
1) The document provides instructions for disassembling and assembling the final drive of a 336D L Mobile Hydraulic Power Unit.
2) The disassembly procedure involves using various tools to remove 25 components of the final drive including gears, seals, plates, and housings.
3) The assembly procedure is the reverse of disassembly and provides instructions for installing the components using loctite and torquing bolts to the specified values.
Caterpillar Cat 336D L Excavator (Prefix JBF) Service Repair Manual Instant D...zan2736ban
This document provides instructions for installing a unit injector sleeve on a Caterpillar C9 engine. It outlines the required tools and gives step-by-step details for cleaning the sleeve and cylinder head bore, lubricating seals, applying retaining compound to the sleeve, and installing the sleeve using a hammer and installer tool. Proper installation is important to prevent leaks that could cause low pressure or oil consumption issues.
Caterpillar Cat 336D L Excavator (Prefix J6D) Service Repair Manual Instant D...zan2736ban
This document provides instructions for disassembling and assembling the final drive of a 336D L Mobile Hydraulic Power Unit. The 25 step disassembly procedure includes removing components like bolts, seals, gears, and housings. The 21 step assembly procedure describes installing these components in reverse order, noting precautions like wearing protective equipment and using torque wrenches to specified settings. Tools required include link brackets, crossblocks, drivers, sockets, and lifting adapters.
Caterpillar Cat 336D L Excavator (Prefix J2F) Service Repair Manual Instant D...zan2736ban
The document provides instructions to remove and install the final drive and travel motor assembly on a 336D L excavator. The removal procedure involves 13 steps including disconnecting hoses, removing bolts, and lifting the assembly off with the aid of tools. The installation procedure reverses these steps, taking care to properly position the components and tighten bolts to the specified torques. Proper containment of fluids and cleaning of parts is emphasized throughout.
Caterpillar Cat 336D L Excavator (Prefix DTS) Service Repair Manual Instant D...zan2736ban
This document provides instructions for disassembling and assembling the piston pump of a 336D L excavator. The disassembly procedure involves removing 30 individual parts from the pump housing in a specific order. The assembly procedure describes installing the parts in the reverse order and notes that some components require special tools or heating/cooling to install properly. Precautions are provided to prevent injury from parts under spring tension.
Caterpillar Cat 336D and 336D L Excavator (Prefix MPL) Service Repair Manual ...zan2736ban
1. The document provides step-by-step instructions for disassembling and assembling the piston pump of a 336D excavator.
2. Disassembly involves removing over 30 individual parts in a specific order, including housings, seals, springs, pistons, and bearings.
3. Assembly requires carefully installing the parts in reverse order and adjusting shims and bearings to ensure proper clearance and operation.
Caterpillar Cat 336D and 336D L Excavator (Prefix KKT) Service Repair Manual ...zan2736ban
1. The document provides instructions for removing and installing various engine components on Caterpillar 336D and 336D L excavators, including the engine oil filter base, engine oil cooler, and hydraulic oil cooler.
2. Removal and installation procedures are outlined in steps with accompanying illustrations. Cleanliness is emphasized and inspecting parts for wear or damage before reassembly.
3. Tools required are listed for some procedures. Proper lifting of heavy components like the hydraulic oil cooler is advised to prevent injury.
Caterpillar Cat 336D and 336D L Excavator (Prefix JBT) Service Repair Manual ...zan2736ban
The document provides instructions for servicing the piston pump (hydraulic fan) on a 336D excavator. It describes how to install the piston pump, connecting hoses and harness. It then details how to disassemble, remove and assemble the piston motor (hydraulic fan), including removing springs and pins, and replacing seals and bearings. Personal protective equipment is recommended when working with spring loaded parts.
More Related Content
Similar to Caterpillar Cat 325C and 325C L Excavator (Prefix JLC) Service Repair Manual Instant Download.pdf
The document provides instructions for removing and installing a crankshaft wear sleeve on a 325C excavator. It describes using special tools to distort the sleeve until it is loose, then removing it from the crankshaft. For installation, a seal locator tool and installer tool are used to position the sleeve and seal and drive them onto the crankshaft. The procedure aims to properly install the sleeve and seal while keeping the components clean.
Caterpillar Cat 325C L Excavator (Prefix JLC) Service Repair Manual (JLC00001...kesi7153062
The document provides instructions for removing and installing a crankshaft wear sleeve on a 325C excavator. It describes using special tools to distort the sleeve until it is loose, then removing it from the crankshaft. For installation, a seal locator tool and installer are used to position the sleeve and seal and drive them onto the crankshaft. The document also provides guidelines for checking bearing clearances using plastic gauge tools.
Caterpillar cat 325 c l excavator (prefix amh) service repair manual (amh0000...fjskeazqkkdmme
This document provides instructions for removing and installing various engine components on Caterpillar 325C and 325C L excavators, including:
- Removing and installing the camshaft, camshaft gear, and camshaft bearings. Proper timing of the camshaft is emphasized.
- Removing and installing the engine oil pan. Safety precautions for hot oil and proper fluid containment are outlined.
- The document contains detailed step-by-step instructions, illustrations, and notes on proper component orientation for each procedure. Required tools are listed.
Caterpillar cat 325 c l excavator (prefix amh) service repair manual (amh0000...fjkskedmme
This document provides instructions for removing and installing various engine components on Caterpillar 325C and 325C L excavators, including:
- Removing and installing the camshaft, camshaft gear, and camshaft bearings. Proper timing of the camshaft is emphasized.
- Removing and installing the engine oil pan. Safety precautions for hot oil and proper fluid containment are outlined.
- The document contains detailed step-by-step instructions, illustrations, and notes on proper component orientation for each procedure. Required tools are listed.
Caterpillar cat 325 c excavator (prefix amh) service repair manual (amh00001 ...ifosodkmsme
The document provides instructions for removing and installing various engine components on a Caterpillar 3126B engine, including:
1. Procedures for removing the camshaft, camshaft gear, camshaft bearings, and engine oil pan. Safety notices and required tools are listed.
2. Instructions for installing the camshaft, camshaft gear, camshaft bearings, and engine oil pan. Diagrams illustrate the component locations and installation steps. Torque specifications and seals/gaskets are addressed.
3. Component removal and installation is described in step-by-step format with references to other relevant sections for some components. Proper cleaning, handling and disposal of fluids
Caterpillar cat 325 c excavator (prefix amh) service repair manual (amh00001 ...fjskekdmjekm
This document provides instructions for removing and installing various engine components on Caterpillar 325C and 325C L excavators, including:
- Removing and installing the camshaft, camshaft gear, and camshaft bearings. Proper timing of the camshaft is emphasized.
- Removing and installing the engine oil pan. Safety precautions for hot oil and proper fluid containment are outlined.
- The document contains detailed step-by-step instructions, illustrations, and notes on proper component orientation for each procedure. Required tools are listed.
Caterpillar Cat 325C L Excavator (Prefix CRB) Service Repair Manual (CRB00001...f8usiejdkmdd
The document provides instructions for removing and installing the camshaft on a Caterpillar 3126B engine used in 325C excavators. The summary is:
1) Remove the lifter group and front cover to access the camshaft. Wire the valve lifters away from the camshaft. Remove the camshaft retainer plate and bolts and pull out the camshaft.
2) Install the camshaft, ensuring the timing marks are aligned. Install the camshaft retainer plate and bolts. Reinstall the lifter group and front cover.
3) The document provides step-by-step instructions for removing and installing the camshaft, camshaft
Caterpillar Cat 325C, 325C L and 325C LN Excavator (Prefix CRB) Service Repai...yan77xunhao
The document provides instructions for removing and installing various engine components on a 325C excavator, including:
1. Removing the camshaft by turning the crankshaft to top center, removing retaining bolts, and lifting out the camshaft.
2. Installing the camshaft by carefully inserting it into place while ensuring proper timing marks are aligned.
3. Removing the camshaft gear by first removing the camshaft, wrapping it to protect it, and pressing it out of the gear in a press. Reinstallation involves heating the gear and pressing it onto the camshaft while aligning the key.
The document provides instructions for removing and installing various engine components on a 325C excavator, including:
1. Removing the camshaft by wiring the valve lifters away, removing retaining bolts, and lifting the camshaft out.
2. Installing the camshaft by carefully inserting it into place while ensuring proper timing marks are aligned.
3. Removing the camshaft bearings using a special tool, and installing new bearings by orienting the oil holes and positioning joints.
The document provides instructions for removing and installing the camshaft on a Caterpillar 3126B engine used in 325C excavators. The summary is:
1) Remove the lifter group and front cover to access the camshaft. Wire the valve lifters away from the camshaft. Remove the camshaft retainer plate and bolts, then remove the camshaft.
2) Install the camshaft, ensuring the timing marks are aligned. Install the camshaft retainer plate and bolts. Install the lifter group and front cover.
3) The document provides step-by-step instructions for removing and installing the camshaft, camshaft gear
Similar to Caterpillar Cat 325C and 325C L Excavator (Prefix JLC) Service Repair Manual Instant Download.pdf (10)
Caterpillar Cat 336D L Excavator (Prefix M4T) Service Repair Manual Instant D...zan2736ban
The document provides instructions for removing and installing a final drive and travel motor on a 336D L excavator. It lists required tools and gives step-by-step instructions that include disconnecting hoses, removing bolts and covers, lifting out the assembly, and reinstalling it in the reverse order. Safety notices are provided regarding containing fluids, cleaning parts, and relieving hydraulic pressure before disassembly.
Caterpillar Cat 336D L Excavator (Prefix LMG) Service Repair Manual Instant D...zan2736ban
The document provides instructions for assembling a swivel component. It lists required tools including link brackets and vacuum caps. The procedure involves cleaning parts, positioning the swivel joint on a repair stand, and reassembling parts like the outside housing, rotor, seals, bolts and washers in the correct order. Thorough cleaning of parts is important before assembly to prevent contamination.
Caterpillar Cat 336D L Excavator (Prefix L5X) Service Repair Manual Instant D...zan2736ban
This document provides instructions for removing and installing the rear gear group and flywheel on a 336D L excavator. The removal procedure involves using various tools to remove bolts, gears, bushings, bearings, and seals. Installation involves cleaning parts and using tools to carefully lower bearings and gears into place while matching specific dimensions, then reinstalling covers, seals, and bolts. Precautions are given to keep parts clean and properly position oil passages.
Caterpillar Cat 336D L Excavator (Prefix JWR) Service Repair Manual Instant D...zan2736ban
The document provides instructions for removing and installing a final drive and travel motor on a 336D L excavator. It lists required tools and gives step-by-step instructions including disconnecting hoses, removing bolts and covers, lifting out the assembly, and reinstalling it in reverse order. Safety notices are provided regarding containing fluids, releasing pressure from the hydraulic system, and preventing contamination.
Caterpillar Cat 336D L Excavator (Prefix JRX) Service Repair Manual Instant D...zan2736ban
1) The document provides instructions for disassembling and assembling the final drive of a 336D L Mobile Hydraulic Power Unit.
2) The disassembly procedure involves using various tools to remove 25 components of the final drive including gears, seals, plates, and housings.
3) The assembly procedure is the reverse of disassembly and provides instructions for installing the components using loctite and torquing bolts to the specified values.
Caterpillar Cat 336D L Excavator (Prefix JBF) Service Repair Manual Instant D...zan2736ban
This document provides instructions for installing a unit injector sleeve on a Caterpillar C9 engine. It outlines the required tools and gives step-by-step details for cleaning the sleeve and cylinder head bore, lubricating seals, applying retaining compound to the sleeve, and installing the sleeve using a hammer and installer tool. Proper installation is important to prevent leaks that could cause low pressure or oil consumption issues.
Caterpillar Cat 336D L Excavator (Prefix J6D) Service Repair Manual Instant D...zan2736ban
This document provides instructions for disassembling and assembling the final drive of a 336D L Mobile Hydraulic Power Unit. The 25 step disassembly procedure includes removing components like bolts, seals, gears, and housings. The 21 step assembly procedure describes installing these components in reverse order, noting precautions like wearing protective equipment and using torque wrenches to specified settings. Tools required include link brackets, crossblocks, drivers, sockets, and lifting adapters.
Caterpillar Cat 336D L Excavator (Prefix J2F) Service Repair Manual Instant D...zan2736ban
The document provides instructions to remove and install the final drive and travel motor assembly on a 336D L excavator. The removal procedure involves 13 steps including disconnecting hoses, removing bolts, and lifting the assembly off with the aid of tools. The installation procedure reverses these steps, taking care to properly position the components and tighten bolts to the specified torques. Proper containment of fluids and cleaning of parts is emphasized throughout.
Caterpillar Cat 336D L Excavator (Prefix DTS) Service Repair Manual Instant D...zan2736ban
This document provides instructions for disassembling and assembling the piston pump of a 336D L excavator. The disassembly procedure involves removing 30 individual parts from the pump housing in a specific order. The assembly procedure describes installing the parts in the reverse order and notes that some components require special tools or heating/cooling to install properly. Precautions are provided to prevent injury from parts under spring tension.
Caterpillar Cat 336D and 336D L Excavator (Prefix MPL) Service Repair Manual ...zan2736ban
1. The document provides step-by-step instructions for disassembling and assembling the piston pump of a 336D excavator.
2. Disassembly involves removing over 30 individual parts in a specific order, including housings, seals, springs, pistons, and bearings.
3. Assembly requires carefully installing the parts in reverse order and adjusting shims and bearings to ensure proper clearance and operation.
Caterpillar Cat 336D and 336D L Excavator (Prefix KKT) Service Repair Manual ...zan2736ban
1. The document provides instructions for removing and installing various engine components on Caterpillar 336D and 336D L excavators, including the engine oil filter base, engine oil cooler, and hydraulic oil cooler.
2. Removal and installation procedures are outlined in steps with accompanying illustrations. Cleanliness is emphasized and inspecting parts for wear or damage before reassembly.
3. Tools required are listed for some procedures. Proper lifting of heavy components like the hydraulic oil cooler is advised to prevent injury.
Caterpillar Cat 336D and 336D L Excavator (Prefix JBT) Service Repair Manual ...zan2736ban
The document provides instructions for servicing the piston pump (hydraulic fan) on a 336D excavator. It describes how to install the piston pump, connecting hoses and harness. It then details how to disassemble, remove and assemble the piston motor (hydraulic fan), including removing springs and pins, and replacing seals and bearings. Personal protective equipment is recommended when working with spring loaded parts.
Caterpillar Cat 330F, 330F L and 330F LN Excavator (Prefix WBA) Service Repai...zan2736ban
The document provides instructions for disassembling a Caterpillar 330F L excavator travel motor. It lists 28 steps to completely disassemble the travel motor, including removing components like the head, springs, pistons, bearings, and housing. Various tools are required, including bolts, nuts, retaining rings, presses, and pullers to separate the individual parts in a specific sequence. Safety precautions are provided throughout to properly release pressures and contain fluids.
Caterpillar Cat 330F, 330F L and 330F LN Excavator (Prefix JHF) Service Repai...zan2736ban
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins by describing how to disassemble the various components of the final drive by removing gears, shafts, carriers, and housings. It then describes the assembly process, which involves pressing in new bearings, installing seals with specialized tools, and using shims to set the proper bearing preload when reassembling components. Precise tools and measurements are required to correctly reassemble the final drive.
Caterpillar Cat 330F and 330F L Excavator (Prefix LCG) Service Repair Manual ...zan2736ban
This document provides instructions for disassembling and assembling a final drive on an excavator model 330F. It involves 37 steps to disassemble the final drive which includes removing gears, shafts, carriers, and housing components. The assembly process involves 33 steps including pressing in new bearings, installing seals, adjusting the bearing preload using shims, and reattaching the sprocket housing. Tools such as retaining ring pliers, eyebolts and a transmission repair stand are required. Precise measurements are taken to determine the correct shim thickness for proper bearing preload.
Caterpillar Cat 330F and 330F L Excavator (Prefix HCK) Service Repair Manual ...zan2736ban
The document provides instructions for disassembling a travel motor. It describes 28 steps to remove parts like the head, brake piston, rotating assembly, bearings, seals, and more. Various tools are required including bolts, nuts, retaining ring pliers, bearing pullers, and more. Safety notices are included to warn of potential spring forces or fluid hazards during disassembly.
Caterpillar Cat 330F and 330F L Excavator (Prefix GHT) Service Repair Manual ...zan2736ban
The document provides disassembly instructions for a 330F and 330F L excavator travel motor over 28 steps. It details removing components like the head, brake piston, rotating assembly, pistons, and seals. Tools include an adapter, nuts, threaded rod, eyebolts, drivers, and pullers. Safety notices warn of spring forces, pressurized air, and containing fluids during disassembly.
Caterpillar Cat 330D2 L Excavator (Prefix ZBF) Service Repair Manual Instant ...zan2736ban
This document provides instructions for disassembling and assembling the final drive of an excavator model 330D2 L. The disassembly process involves using various tools to remove over 30 individual parts from the final drive assembly, including gears, shafts, seals, and housings. The assembly section outlines 37 steps to reinstall these parts in reverse order, noting that cleanliness is important, old seals should be replaced, and parts should be lubricated before assembly. Precise measurements and shimming are required to set proper bearing preload when reinstalling the main housing.
Caterpillar Cat 330D2 L Excavator (Prefix SZK) Service Repair Manual Instant ...zan2736ban
This document provides instructions for disassembling and assembling the final drive of an excavator model 330D2 L. The disassembly process involves using various tools to remove over 30 individual parts from the final drive assembly, including gears, shafts, seals, and housings. The assembly process similarly provides step-by-step instructions for installing the parts back onto the final drive, noting the importance of cleanliness and applying lubricants between parts. Proper bearing preload is achieved through measuring clearance and installing shims as needed.
Caterpillar Cat 330D2 L Excavator (Prefix PTE) Service Repair Manual Instant ...zan2736ban
This document provides instructions for removing and installing a turbocharger for top mounted engines. The removal process involves disconnecting hoses and tubes, removing bolts and nuts, and taking off the turbocharger assembly. For installation, components are cleaned and inspected, gaskets and seals are installed, bolts are tightened in a specified order and torque, and hoses/tubes are reconnected. Tools, safety notices, and illustrations are included to aid the process.
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR JLC
Configuration: 325C & 325C L Excavators JLC00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i01931442
Crankshaft Wear Sleeve (Rear) - Remove - If Equipped
SMCS - 1161-011-ZV
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 4C-4869 Distorter Ring 1
B 5P-7312 Seal Distorter 1
Start By:
a. Remove the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear
Seal - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
325C & 325C L Excavators JLC00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. Illustration 1 g00614029
Note: Wear sleeves are not installed at the factory. The wear sleeve is included with the
replacement rear seal.
1. Install Tooling (A) in the bore of the crankshaft rear sleeve.
2. Install Tooling (B) between Tooling (A) and the crankshaft wear sleeve. Turn Tooling (B)
until the edge of Tooling (B) makes a crease in the crankshaft wear sleeve. Make a crease in
the crankshaft wear sleeve at two other locations around the crankshaft wear sleeve until the
crankshaft wear sleeve is loose.
3. Remove Tooling (B), Tooling (A), and the crankshaft wear sleeve from the end of the
crankshaft.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jul 9 23:41:06 UTC+0800 2020
2/2
325C & 325C L Excavators JLC00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR JLC
Configuration: 325C & 325C L Excavators JLC00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i01929732
Crankshaft Wear Sleeve (Rear) - Install
SMCS - 1161-012-ZV
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
C(1)
132-8772 Seal Locator 1
D(1)
1U-7596 Bolt 2
E(1)
1U-7597 Sleeve Ring 1
F(1)
1U-7594 Seal Installer 1
G(1)
9S-8858 Nut 1
(1)
Part of the 1U-7598 Seal Installer
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Ensure that the rear of the crankshaft is thoroughly clean and dry prior to the installation of
the crankshaft rear seal.
1/3
325C & 325C L Excavators JLC00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. Illustration 1 g01003875
2. Fasten Tooling (C) to the rear of the crankshaft with Tooling (D). Hand tighten Tooling (D).
3. Position the crankshaft rear seal and crankshaft rear sleeve (1) on Tooling (C). Position
Tooling (E) on Tooling (C).
Illustration 2 g01003866
Typical example
4. Position Tooling (F) over Tooling (C) and Tooling (E). Install Tooling (G). Tighten Tooling
(G) in order to install the crankshaft rear seal and the crankshaft wear sleeve.
5. Remove Tooling (G), Tooling (F), and Tooling (E). Turn over Tooling (E). Install Tooling
(E), Tooling (F), and Tooling (G). Tighten Tooling (G) in order to complete the installation
of the crankshaft rear seal and the crankshaft wear sleeve.
6. Remove Tooling (G) and Tooling (F). Check Tooling (E) and Tooling (C). The faces of
Tooling (E) and Tooling (C) will be flush if the crankshaft rear seal and the crankshaft wear
sleeve are properly installed. Refer to the Specifications module for more information.
7. Remove Tooling (E), Tool (E), and Tooling (C).
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
2/3
325C & 325C L Excavators JLC00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR JLC
Configuration: 325C & 325C L Excavators JLC00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i02374834
Crankshaft - Install
SMCS - 1202-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8T-5096 Dial Indicator Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Ensure that the crankshaft main bearing tabs engage with the grooves
in the block and the crankshaft main bearing cap.
Note: The number six main bearing is the thrust bearing.
1. Clean the bearing surfaces in the cylinder block for the main bearings. Apply clean engine
oil on the upper main bearing. Do not put engine oil on the back side of the bearing
1/3
325C & 325C L Excavators JLC00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. surfaces. Install the upper main bearing in the cylinder block. Ensure that the tab on the
back side of the bearing engages with the groove in the cylinder block.
Illustration 1 g01184978
2. Put clean engine oil on the journals of the crankshaft bearing. Attach a suitable lifting
device to crankshaft (1). The weight of crankshaft (1) is approximately 60 kg (132 lb).
Carefully install the crankshaft in the cylinder block.
3. Clean the bearing surface of the main bearing caps. Install the lower main bearing in the
crankshaft main bearing caps. Ensure that the tab on the back side of the bearing engages
with the groove in the main bearing cap. Apply clean engine oil on the lower main bearing.
Do not put engine oil on the back side of the bearing surfaces.
4. Install crankshaft main bearing caps with the part numbers toward the right hand side of the
cylinder block. The numbers should start at the front of the engine. Place clean engine oil or
Molylube on the bolt threads and the washers.
2/3
325C & 325C L Excavators JLC00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Illustration 2 g01028042
5. Install the bolts for main bearing caps (2). Tighten the bolts to a torque of 54 ± 7 N·m
(40 ± 5 lb ft).
6. Turn the bolts for an additional 90 ± 5 degrees (1/4 turn).
7. Install connecting rod caps (3). Refer to Disassembly and Assembly, "Pistons and
Connecting Rods - Install".
8. Check the end play of crankshaft (1) with Tooling (A). The end play must be
0.07 to 0.32 mm (0.003 to 0.013 inch).
End By:
a. Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Install".
b. Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump -
Install".
c. Install the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing -
Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jul 9 23:42:58 UTC+0800 2020
3/3
325C & 325C L Excavators JLC00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR JLC
Configuration: 325C & 325C L Excavators JLC00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i01984006
Crankshaft Gear - Remove and Install
SMCS - 1204-010-GE
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8B-7551 Bearing Puller 1
8B-7549 Puller Leg 2
3H-0465 Push-Puller Plate 4
6B-6682 Full Nut 2
8B-7560 Step Plate 1
1P-0820 Hydraulic Puller 1
9U-6600 Hand Hydraulic Pump 1
Start By:
a. Remove the crankshaft. Refer to Disassembly and Assembly, "Crankshaft - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
325C & 325C L Excavators JLC00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. Illustration 1 g00988783
1. Use Tooling (A) in order to remove crankshaft gear (3) from crankshaft (1).
2. Remove woodruff key (2).
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3
325C & 325C L Excavators JLC00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Illustration 2 g00988783
1. Position woodruff key (2) in crankshaft (1).
Hot oil and hot components can cause personal injury. Do not allow hot
oil or hot components to contact the skin.
2. Raise the temperature of crankshaft gear (3). Install crankshaft gear (3) on crankshaft (1).
End By:
a. Install the crankshaft. Refer to Disassembly and Assembly, "Crankshaft - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jul 9 23:43:54 UTC+0800 2020
3/3
325C & 325C L Excavators JLC00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR JLC
Configuration: 325C & 325C L Excavators JLC00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i05977048
Bearing Clearance - Check
SMCS - 1203-535; 1219-535
Measurement Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
198-9142
Plastic Gauge (Green)
0.025 to 0.076 mm
(0.001 to 0.003 inch)
1
198-9143
Plastic Gauge (Red)
0.051 to 0.152 mm
(0.002 to 0.006 inch)
1
198-9144
Plastic Gauge (Blue)
0.102 to 0.229 mm
(0.004 to 0.009 inch)
1
198-9145
Plastic Gauge (Yellow)
0.230 to 0.510 mm
(0.009 to 0.020 inch)
1
Note: Plastic gauge may not be necessary when the engine is in the chassis.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
325C & 325C L Excavators JLC00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Note: Cat does not recommend the checking of the actual bearing clearances particularly on small
engines. This is because of the possibility of obtaining inaccurate results and the possibility of
damaging the bearing or the journal surfaces. Each Cat engine bearing is quality checked for
specific wall thickness.
Note: The measurements should be within specifications and the correct bearings should be used.
If the crankshaft journals and the bores for the block and the rods were measured during
disassembly, no further checks are necessary. However, if the technician still wants to measure the
bearing clearances, Tooling (A) is an acceptable method. Tooling (A) is less accurate on journals
with small diameters if clearances are less than 0.10 mm (0.004 inch).
NOTICE
Lead wire, shim stock or a dial bore gauge can damage the bearing
surfaces.
The technician must be very careful to use Tooling (A) correctly. The following points must be
remembered:
• Ensure that the backs of the bearings and the bores are clean and dry.
• Ensure that the bearing locking tabs are properly seated in the tab grooves.
• The crankshaft must be free of oil at the contact points of Tooling (A).
1. Put a piece of Tooling (A) on the crown of the bearing that is in the cap.
Note: Do not allow Tooling (A) to extend over the edge of the bearing.
2. Use the correct torque-turn specifications in order to install the bearing cap. Do not use an
impact wrench. Be careful not to dislodge the bearing when the cap is installed.
Note: Do not turn the crankshaft when Tooling (A) is installed.
3. Carefully remove the cap, but do not remove Tooling (A). Measure the width of Tooling
(A) while Tooling (A) is in the bearing cap or on the crankshaft journal. Refer to Illustration
1.
2/3
325C & 325C L Excavators JLC00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Illustration 1 g01152855
Typical Example
4. Remove all of Tooling (A) before you install the bearing cap.
Note: When Tooling (A) is used, the readings can sometimes be unclear. For example, all
parts of Tooling (A) are not the same width. Measure the major width in order to ensure that
the parts are within the specification range. Refer to Specifications Manual, "Connecting
Rod Bearing Journal" and Specifications Manual, "Main Bearing Journal" for the correct
clearances.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jul 9 23:44:49 UTC+0800 2020
3/3
325C & 325C L Excavators JLC00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR JLC
Configuration: 325C & 325C L Excavators JLC00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i01984226
Idler Pulley - Remove and Install
SMCS - 1358-010
Illustration 1 g01028295
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jul 9 23:45:45 UTC+0800 2020
1/1
325C & 325C L Excavators JLC00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR JLC
Configuration: 325C & 325C L Excavators JLC00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i01930316
Belt Tensioner - Remove and Install
SMCS - 1358-010
Removal Procedure
Illustration 1 g01011962
1. Use a breaker bar to release the tension on belt tensioner (1). Remove the drive belt.
2. Remove bolt (2) and belt tensioner (1).
Installation Procedure
1/2
325C & 325C L Excavators JLC00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Illustration 2 g01011962
1. Position belt tensioner (1) on the cylinder block. Install bolt (2).
2. Install the drive belt. Use a breaker bar to release tension on belt tensioner (1).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jul 9 23:46:41 UTC+0800 2020
2/2
325C & 325C L Excavators JLC00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR JLC
Configuration: 325C & 325C L Excavators JLC00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i01379733
Electronic Control Module - Remove and Install
SMCS - 1901-010
Removal Procedure
1. Remove the fuel lines from the fuel cooled ECM (if equipped).
Illustration 1 g00609591
Typical example
2. Loosen screw (1) until wiring harness (4) can be disconnected. Disconnect wiring harness
(4) from electronic control module (2).
3. Remove four bolts (3). Remove the electronic control module from the engine.
Installation Procedure
1/2
325C & 325C L Excavators JLC00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Illustration 2 g00609591
Typical example
1. Position electronic control module (2) on the engine and install four bolts (3).
2. Connect wiring harness (4) to electronic control module (2). Tighten screw (1) to a torque of
6 ± 1 N·m (53 ± 9 lb in).
3. Reconnect the fuel lines to the fuel cooled ECM (if equipped).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jul 9 23:47:37 UTC+0800 2020
2/2
325C & 325C L Excavators JLC00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR JLC
Configuration: 325C & 325C L Excavators JLC00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i01378281
Alternator - Remove and Install
SMCS - 1405-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7117 Breaker Bar 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Use Tool (A) to release the tension on the belt tensioner.
2. Remove the drive belt from the alternator drive pulley.
1/3
325C & 325C L Excavators JLC00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. Illustration 1 g00728265
3. Place an index mark on all electrical wires that are connected to alternator (1). Disconnect
all electrical wires from the alternator.
4. Remove two bolts (2).
5. Remove alternator (1) from the mounting bracket.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1U-7117 Breaker Bar 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3
325C & 325C L Excavators JLC00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Illustration 2 g00728265
1. Position alternator (1) on the mounting bracket. Install two bolts (2).
2. Install the drive belt on the alternator drive pulley.
3. Use Tool (A) on the belt tensioner in order to tighten the drive belt.
4. Connect all electrical wires to the alternator. Use the index marks to correctly connect the
wires.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jul 9 23:48:32 UTC+0800 2020
3/3
325C & 325C L Excavators JLC00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
24. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR JLC
Configuration: 325C & 325C L Excavators JLC00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i06798491
Electric Starting Motor - Remove and Install
SMCS - 1453-010
Removal Procedure
Personal injury can result from failure to disconnect the battery.
First, disconnect the negative battery cable. Then, disconnect the
positive battery cable.
A positive power lead can cause sparks if the battery is not
disconnected. Sparks can possibly result in battery explosion or fire.
Illustration 1 g06119357
1/2
325C & 325C L Excavators JLC00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
25. 1. Disconnect cable strap (1).
2. Place an index mark on all of the harness assemblies. Disconnect the harness assemblies
from electric starting motor (2).
3. Fasten a suitable lifting device to electric starting motor (4). The weight of electric starting
motor (4) is approximately 35 kg (77 lb).
4. Remove bolts (3).
5. Remove electric starting motor (4) and the gasket from the flywheel housing.
Installation Procedure
1. Install electric starting motor (4) in reverse order of removal.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jul 9 23:49:28 UTC+0800 2020
2/2
325C & 325C L Excavators JLC00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...