This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a C6.4 engine. It describes using various tools to compress springs, remove components, and install new parts. Removal involves turning the cylinder head upside down, then using a valve seat extractor tool to pull out old inserts. Installation requires cleaning components, lubricating guides, and pressing new inserts into place with an installer tool so they protrude the correct amount. Proper cleaning, compression, and tool use is emphasized to prevent damage and ensure correct assembly.
Caterpillar cat 323 d l excavator (prefix gtf) service repair manual (gtf0000...fjjsekmsmmes
This document provides instructions for removing and installing inlet and exhaust valve seats in a C6.4 engine. It describes using various tools to remove the valves, valve guides, and valve seat inserts from the cylinder head. It also details how to clean, inspect, and lubricate components before reinstalling the valve seat inserts, guides, and valves in the proper order and orientation. Protective equipment is recommended to safely compress springs during the process.
Caterpillar cat 311 d lrr excavator (prefix cla) service repair manual (cla00...dkdmidkkdk
This document provides instructions for removing and installing inlet and exhaust valves and valve guides on a C4.2 engine. The procedure involves using various tools to compress springs, remove components in the proper order, clean parts, and lubricate components before installation. Precautions are outlined to prevent injury and ensure proper assembly.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing valves, valve guides, and the engine oil cooler. Precautions are outlined to prevent contamination and contain fluids.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing valves, valve guides, and installing new components. The document also describes draining coolant and removing bolts to take off the engine oil cooler.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
Caterpillar cat 311 d lrr excavator (prefix cla) service repair manual (cla00...fjjsekkdmme
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
Caterpillar cat 323 d l excavator (prefix gtf) service repair manual (gtf0000...fjjsekmsmmes
This document provides instructions for removing and installing inlet and exhaust valve seats in a C6.4 engine. It describes using various tools to remove the valves, valve guides, and valve seat inserts from the cylinder head. It also details how to clean, inspect, and lubricate components before reinstalling the valve seat inserts, guides, and valves in the proper order and orientation. Protective equipment is recommended to safely compress springs during the process.
Caterpillar cat 311 d lrr excavator (prefix cla) service repair manual (cla00...dkdmidkkdk
This document provides instructions for removing and installing inlet and exhaust valves and valve guides on a C4.2 engine. The procedure involves using various tools to compress springs, remove components in the proper order, clean parts, and lubricate components before installation. Precautions are outlined to prevent injury and ensure proper assembly.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing valves, valve guides, and the engine oil cooler. Precautions are outlined to prevent contamination and contain fluids.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing valves, valve guides, and installing new components. The document also describes draining coolant and removing bolts to take off the engine oil cooler.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
Caterpillar cat 311 d lrr excavator (prefix cla) service repair manual (cla00...fjjsekkdmme
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
Caterpillar cat 311 d lrr excavator (prefix cla) service repair manual (cla00...fjjskekmsemm
This document provides the procedure for removing and installing inlet and exhaust valves and valve guides on a Caterpillar C4.2 engine. The procedure involves using various tools to compress springs, remove components in the proper order, clean parts, and inspect for wear. Valves, guides, seals and other components are then reinstalled in the reverse order, taking care to lubricate parts and set components to the correct specifications.
Caterpillar cat 311 d lrr excavator (prefix cla) service repair manual (cla00...fjsekdmmeed
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
1. The document provides instructions for removing and installing inlet and exhaust valves and valve guides on a Caterpillar C4.2 engine.
2. The removal procedure includes using various tools to compress the valve springs, remove the valve keepers and other components, and extract the valves and valve guides.
3. The installation procedure specifies cleaning and lubricating the components, and using tools to reinstall the valve guides at the proper height and compress the springs to reinstall the valves and associated parts.
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and an engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to disassemble and remove the components, cleaning requirements, and installation procedures.
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and an engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to disassemble components like removing valve springs and stem seals, and installing new valve stem seals. Precautions are outlined to keep parts clean and contain fluids during the repair work.
Caterpillar cat 323 d excavator (prefix wgc) service repair manual (wgc00001 ...idkkdmmdd
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C6.4 engine. It outlines the required tools and safety precautions. The procedure involves using a valve spring compressor tool to compress the valve spring and remove the retainer, spring, and valve components. Reinstallation follows the reverse order, ensuring parts are clean and applying the proper pressure with the compressor tool. The summary is intended only to convey the main focus and steps involved, not to replace reading the full instructions.
Caterpillar cat 323 d l excavator (prefix wgc) service repair manual (wgc0000...idkkmdmd
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C6.4 engine. It outlines the required tools and safety precautions. The procedure involves using a valve spring compressor tool to compress the valve spring and remove the retainer, spring, and valve components. Reinstallation follows the reverse order, ensuring parts are clean and applying the proper pressure with the compressor tool. The summary is intended only to convey the main focus and steps involved, not serve as a replacement for the full instructions.
Caterpillar cat 323 d l excavator (prefix wgc) service repair manual (wgc0000...dhjfjkmmmde
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C6.4 engine. It describes the required tools and safety precautions. The procedure involves using a valve spring compressor tool to compress the valve spring and remove the retainer, spring, and valve keeper. Installation is the reverse process of cleaning components and lubricating the valve stem before reinstalling the valve keeper, spring, and retainer while compressing the spring with the tool.
Caterpillar cat 323 d excavator (prefix wgc) service repair manual (wgc00001 ...fhsjekkdkem
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C6.4 engine. It describes the required tools and safety precautions. The procedure involves using a valve spring compressor tool to compress the valve spring and remove the retainer, spring, and valve keeper. The process is then reversed to install the new parts, ensuring the valve stem seal is installed correctly. Similar instructions are provided for removing and installing the valve guides.
Caterpillar cat 323 d excavator (prefix wgc) service repair manual (wgc00001 ...fhsejkdkmem
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C6.4 engine. It describes the required tools and safety precautions. The procedure involves using a valve spring compressor tool to compress the valve spring and remove the retainer, spring, and valve keeper. Installation is the reverse process of cleaning components and lubricating the valve stem before reinstalling the valve keeper, spring, and retainer while compressing the spring with the tool.
The document provides instructions for removing and installing various engine components on a Caterpillar C4.2 engine, including:
- Removing and installing the flywheel housing, which requires removing bolts and installing a new gasket.
- Removing the crankshaft pulley using pullers and removing the wear sleeve if needed. Installation requires heating the sleeve and tightening a nut.
- Removing the crankshaft front seal by drilling holes and pulling it out, being careful not to damage the crankshaft. Installation uses a installer tool and applying oil.
Caterpillar Cat 313F L Excavator (Prefix NLG) Service Repair Manual (NLG00001...fusjekkdmdmd2w
This document provides instructions for removing the front housing on a C4.4 engine. The steps include:
1. Removing other components like the fan, crankshaft pulley, oil pan, accessory drive, water pump and timing gears.
2. Disconnecting wiring, cutting cable straps and removing bolts to separate the bypass tube from the housing and cylinder head.
3. Removing bolts of different lengths to detach the front housing from the cylinder block, and removing the gasket and thrust washer.
The document provides instructions for removing and installing various components of a Caterpillar C4.2 engine, including the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The procedures include using various tools to remove bolts, nuts, seals, and other parts. Cleanliness is emphasized to prevent contamination.
This document provides instructions for removing the front housing on a C4.4 engine. It involves:
1. Removing various other components first like the fan, crankshaft pulley, oil pan, accessory drive, water pump and timing gears.
2. Disconnecting a harness assembly and removing bolts that secure a bypass tube to the front housing.
3. Removing bolts of various lengths that secure the front housing, and then removing the front housing from the engine.
The document provides disassembly instructions for the final drive, travel motor, counterbalance valve, and other components of excavator models 313D2 and 313D2 GC. It lists required tools and outlines multi-step procedures involving draining fluids, removing fittings and plates, using pullers to remove bearings, and disassembling springs, pistons, and other internal parts while taking safety precautions for released pressures. Detailed illustrations supplement each step.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists required tools and outlines 15 steps to disassemble the final drive, including draining oil and removing sprockets, valves, seals, and bearings. It then details 19 additional steps to disassemble the travel motor and counterbalance valve, removing pistons, plates, springs, and seals. Personal injury warnings are included to release pressures and spring forces safely when disassembling components.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 15 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 16 steps to disassemble the counterbalance valve. Safety notices are included regarding releasing pressures and springs.
This document provides instructions for disassembling the final drive, travel motor, and various other components of a 313D2 excavator. It lists the required tools and outlines 16 steps to disassemble parts like the final drive, traction control valve, counterbalance valve, travel motor, and barrel assembly. Safety notices are included to warn of potential injuries from parts propelled by springs or pressurized hydraulic fluid.
This document provides instructions for disassembling and assembling the travel motor of a 313D2 excavator. The disassembly process involves 27 steps to remove components like the head, brake piston, barrel assembly, springs and seals. The assembly process reverses the disassembly with 23 steps like installing seals, springs, piston assemblies and keys in their proper positions and orientations. Special tools and precautions are noted to prevent damage and ensure correct assembly.
The document provides disassembly instructions for the final drive, travel motor, counterbalance valve, and other components of excavator models 313D2 and 313D2 GC. It lists required tools and outlines multi-step procedures for removing parts like sprockets, valves, pistons, springs, and seals. Safety notices warn of risks like fluid pressure, heavy component weights, and released spring forces during the disassembly process.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists over 30 detailed steps to disassemble components like the final drive, travel motor barrel assembly, planetary gear assembly, and counterbalance valve housing. Safety warnings are provided throughout to warn of potential injuries from parts under spring tension or residual fluid pressure. Required tools include link brackets, a transmission repair stand, bolts, pullers, retaining ring pliers, and spanner wrenches.
1) The document provides disassembly instructions for components of a 313D excavator including the final drive, travel motor, counterbalance valve, and traction control valve.
2) It lists required tools and safety precautions and provides a step-by-step process to remove each part, noting identification marks and order of components.
3) Detailed illustrations accompany each step to show how to remove components like sprockets, valves, springs, gears, plates, and seals. Proper handling and storage of fluids is also addressed.
More Related Content
Similar to Caterpillar Cat 323D L Excavator (Prefix GTF) Service Repair Manual (GTF00001 and up).pdf
Caterpillar cat 311 d lrr excavator (prefix cla) service repair manual (cla00...fjjskekmsemm
This document provides the procedure for removing and installing inlet and exhaust valves and valve guides on a Caterpillar C4.2 engine. The procedure involves using various tools to compress springs, remove components in the proper order, clean parts, and inspect for wear. Valves, guides, seals and other components are then reinstalled in the reverse order, taking care to lubricate parts and set components to the correct specifications.
Caterpillar cat 311 d lrr excavator (prefix cla) service repair manual (cla00...fjsekdmmeed
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
1. The document provides instructions for removing and installing inlet and exhaust valves and valve guides on a Caterpillar C4.2 engine.
2. The removal procedure includes using various tools to compress the valve springs, remove the valve keepers and other components, and extract the valves and valve guides.
3. The installation procedure specifies cleaning and lubricating the components, and using tools to reinstall the valve guides at the proper height and compress the springs to reinstall the valves and associated parts.
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and an engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to disassemble and remove the components, cleaning requirements, and installation procedures.
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and an engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to disassemble components like removing valve springs and stem seals, and installing new valve stem seals. Precautions are outlined to keep parts clean and contain fluids during the repair work.
Caterpillar cat 323 d excavator (prefix wgc) service repair manual (wgc00001 ...idkkdmmdd
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C6.4 engine. It outlines the required tools and safety precautions. The procedure involves using a valve spring compressor tool to compress the valve spring and remove the retainer, spring, and valve components. Reinstallation follows the reverse order, ensuring parts are clean and applying the proper pressure with the compressor tool. The summary is intended only to convey the main focus and steps involved, not to replace reading the full instructions.
Caterpillar cat 323 d l excavator (prefix wgc) service repair manual (wgc0000...idkkmdmd
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C6.4 engine. It outlines the required tools and safety precautions. The procedure involves using a valve spring compressor tool to compress the valve spring and remove the retainer, spring, and valve components. Reinstallation follows the reverse order, ensuring parts are clean and applying the proper pressure with the compressor tool. The summary is intended only to convey the main focus and steps involved, not serve as a replacement for the full instructions.
Caterpillar cat 323 d l excavator (prefix wgc) service repair manual (wgc0000...dhjfjkmmmde
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C6.4 engine. It describes the required tools and safety precautions. The procedure involves using a valve spring compressor tool to compress the valve spring and remove the retainer, spring, and valve keeper. Installation is the reverse process of cleaning components and lubricating the valve stem before reinstalling the valve keeper, spring, and retainer while compressing the spring with the tool.
Caterpillar cat 323 d excavator (prefix wgc) service repair manual (wgc00001 ...fhsjekkdkem
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C6.4 engine. It describes the required tools and safety precautions. The procedure involves using a valve spring compressor tool to compress the valve spring and remove the retainer, spring, and valve keeper. The process is then reversed to install the new parts, ensuring the valve stem seal is installed correctly. Similar instructions are provided for removing and installing the valve guides.
Caterpillar cat 323 d excavator (prefix wgc) service repair manual (wgc00001 ...fhsejkdkmem
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C6.4 engine. It describes the required tools and safety precautions. The procedure involves using a valve spring compressor tool to compress the valve spring and remove the retainer, spring, and valve keeper. Installation is the reverse process of cleaning components and lubricating the valve stem before reinstalling the valve keeper, spring, and retainer while compressing the spring with the tool.
Similar to Caterpillar Cat 323D L Excavator (Prefix GTF) Service Repair Manual (GTF00001 and up).pdf (10)
The document provides instructions for removing and installing various engine components on a Caterpillar C4.2 engine, including:
- Removing and installing the flywheel housing, which requires removing bolts and installing a new gasket.
- Removing the crankshaft pulley using pullers and removing the wear sleeve if needed. Installation requires heating the sleeve and tightening a nut.
- Removing the crankshaft front seal by drilling holes and pulling it out, being careful not to damage the crankshaft. Installation uses a installer tool and applying oil.
Caterpillar Cat 313F L Excavator (Prefix NLG) Service Repair Manual (NLG00001...fusjekkdmdmd2w
This document provides instructions for removing the front housing on a C4.4 engine. The steps include:
1. Removing other components like the fan, crankshaft pulley, oil pan, accessory drive, water pump and timing gears.
2. Disconnecting wiring, cutting cable straps and removing bolts to separate the bypass tube from the housing and cylinder head.
3. Removing bolts of different lengths to detach the front housing from the cylinder block, and removing the gasket and thrust washer.
The document provides instructions for removing and installing various components of a Caterpillar C4.2 engine, including the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The procedures include using various tools to remove bolts, nuts, seals, and other parts. Cleanliness is emphasized to prevent contamination.
This document provides instructions for removing the front housing on a C4.4 engine. It involves:
1. Removing various other components first like the fan, crankshaft pulley, oil pan, accessory drive, water pump and timing gears.
2. Disconnecting a harness assembly and removing bolts that secure a bypass tube to the front housing.
3. Removing bolts of various lengths that secure the front housing, and then removing the front housing from the engine.
The document provides disassembly instructions for the final drive, travel motor, counterbalance valve, and other components of excavator models 313D2 and 313D2 GC. It lists required tools and outlines multi-step procedures involving draining fluids, removing fittings and plates, using pullers to remove bearings, and disassembling springs, pistons, and other internal parts while taking safety precautions for released pressures. Detailed illustrations supplement each step.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists required tools and outlines 15 steps to disassemble the final drive, including draining oil and removing sprockets, valves, seals, and bearings. It then details 19 additional steps to disassemble the travel motor and counterbalance valve, removing pistons, plates, springs, and seals. Personal injury warnings are included to release pressures and spring forces safely when disassembling components.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 15 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 16 steps to disassemble the counterbalance valve. Safety notices are included regarding releasing pressures and springs.
This document provides instructions for disassembling the final drive, travel motor, and various other components of a 313D2 excavator. It lists the required tools and outlines 16 steps to disassemble parts like the final drive, traction control valve, counterbalance valve, travel motor, and barrel assembly. Safety notices are included to warn of potential injuries from parts propelled by springs or pressurized hydraulic fluid.
This document provides instructions for disassembling and assembling the travel motor of a 313D2 excavator. The disassembly process involves 27 steps to remove components like the head, brake piston, barrel assembly, springs and seals. The assembly process reverses the disassembly with 23 steps like installing seals, springs, piston assemblies and keys in their proper positions and orientations. Special tools and precautions are noted to prevent damage and ensure correct assembly.
The document provides disassembly instructions for the final drive, travel motor, counterbalance valve, and other components of excavator models 313D2 and 313D2 GC. It lists required tools and outlines multi-step procedures for removing parts like sprockets, valves, pistons, springs, and seals. Safety notices warn of risks like fluid pressure, heavy component weights, and released spring forces during the disassembly process.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists over 30 detailed steps to disassemble components like the final drive, travel motor barrel assembly, planetary gear assembly, and counterbalance valve housing. Safety warnings are provided throughout to warn of potential injuries from parts under spring tension or residual fluid pressure. Required tools include link brackets, a transmission repair stand, bolts, pullers, retaining ring pliers, and spanner wrenches.
1) The document provides disassembly instructions for components of a 313D excavator including the final drive, travel motor, counterbalance valve, and traction control valve.
2) It lists required tools and safety precautions and provides a step-by-step process to remove each part, noting identification marks and order of components.
3) Detailed illustrations accompany each step to show how to remove components like sprockets, valves, springs, gears, plates, and seals. Proper handling and storage of fluids is also addressed.
This document provides instructions for removing and installing the front gear group on a Caterpillar 312E or 312E L excavator engine. The removal procedure involves using tools to lock the crankshaft, camshaft, and fuel injection pump in position before loosening threaded inserts on the rocker arms. Several gears and other components are then removed from the front of the engine housing. The installation procedure outlines cleaning and inspecting parts before reinstalling components in reverse order, maintaining proper positioning and locking of internal components.
Caterpillar Cat 312D2 L Excavator (Prefix WHJ) Service Repair Manual (WHJ0000...fusjekkdmdmd2w
The document provides instructions for installing and removing various engine components on a Caterpillar 3054C engine, including:
- Installing the flywheel, which involves heating the ring gear, positioning the flywheel with guide bolts, and tightening the bolts to the specified torque.
- Removing the crankshaft rear seal housing assembly, which is non-serviceable and must be replaced as a unit.
- Installing the crankshaft rear seal housing assembly using alignment tools and tightening the setscrews in a specific order to the specified torque.
- Removing and installing an optional crankshaft wear sleeve using pullers and installer/locator tools, to re
Caterpillar Cat 312D2 L Excavator (Prefix MPP) Service Repair Manual (MPP0000...fusjekkdmdmd2w
This document provides disassembly instructions for the final drive, travel motor, and other components of a 312D2 L excavator. It lists the required tools and outlines 23 steps to disassemble parts like the final drive, travel motor, counterbalance valve, and traction control valve. Safety notices are included throughout to warn of potential injuries from parts under spring pressure or hydraulic oil.
Caterpillar Cat 312D2 L Excavator (Prefix MGJ) Service Repair Manual (MGJ0000...fusjekkdmdmd2w
The documents provide instructions for installing and removing various engine components on a Caterpillar 3054C engine, including:
1. Installing the flywheel, which involves heating the ring gear, cleaning parts, using guide bolts and lifting devices, and tightening bolts to the specified torque.
2. Removing the crankshaft rear seal, which is non-serviceable, requiring replacement of the entire housing assembly after removing setscrews.
3. Installing the crankshaft rear seal housing assembly using an alignment tool and tightening setscrews to the specified torque.
Caterpillar Cat 312D2 L Excavator (Prefix KLE) Service Repair Manual (KLE0000...fusjekkdmdmd2w
This document provides instructions for disassembling components of an excavator including the final drive, travel motor, counterbalance valve, and barrel assembly. It lists required tools and outlines multi-step procedures involving removing fittings, draining fluids, loosening bolts, using pullers to remove bearings and seals, and noting part orientations for reassembly. Safety notices warn of risks such as fluid pressure, heavy component weights, and released spring forces.
Caterpillar Cat 312D2 L Excavator (Prefix GWN) Service Repair Manual (GWN0000...fusjekkdmdmd2w
This document provides instructions for disassembling components of an excavator including the final drive, travel motor, counterbalance valve, and barrel assembly. It lists required tools and outlines 16 steps to disassemble parts like the traction control valve, bearing, relief valve assemblies, piston assemblies, springs, and seals. Safety notices are included to warn of potential injuries from parts propelled by springs or pressurized hydraulic fluid.
Caterpillar Cat 312D2 L Excavator (Prefix FAB) Service Repair Manual (FAB0000...fusjekkdmdmd2w
This document provides disassembly instructions for the final drive, travel motor, and other components of a 312D2 L excavator. It lists the required tools and outlines 23 steps to disassemble parts like the final drive, travel motor, counterbalance valve, and traction control valve. Safety notices are included throughout to warn of potential injuries from parts under spring pressure or hydraulic oil.
Caterpillar Cat 312D2 L Excavator (Prefix DGF) Service Repair Manual (DGF0000...fusjekkdmdmd2w
This document provides instructions for removing and installing a camshaft on a Caterpillar 3054C engine. The key steps are:
1. Remove the rocker shaft assembly, pushrods, and front housing.
2. Turn the engine upside down so the valve lifters are away from the camshaft.
3. Carefully remove the camshaft from the cylinder block.
4. Ensure the camshaft is clean and lubricated with oil before installing it in the reverse order of removal. Special care must be taken not to damage the lobes or bearings.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR GTF
Configuration: 323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i06051426
Inlet and Exhaust Valves - Remove and Install
SMCS - 1105-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8S-6691 Cylinder Head Repair Stand 1
B 9U-6195 Valve Spring Compressor Gp 1
C 5P-1720 Seal Pick 1
Start By:
a. Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Note the location and orientation of all components for assembly purposes.
1. Clean the bottom face of the cylinder head. Check the depth of the valves below the face of
the cylinder head before the valve springs are removed. Refer to Specifications, "Cylinder
Head Valves" for the correct dimensions.
1/6
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. 2. Place a temporary identification mark on the heads of the valves in order to identify the
correct position.
Illustration 1 g01376164
3. Use a suitable lifting device in order to position cylinder head (1) onto Tooling (A) with the
valve springs upward. The weight of cylinder head (1) is approximately 113 kg (250 lb).
Note: Ensure that cylinder head (1) is kept on a clean, soft surface in order to prevent
damage to the machined face.
Illustration 2 g01376174
2/6
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g01376184
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
4. Install Tooling (B) on cylinder head (1) in order to compress valve spring (5).
NOTICE
Ensure that the valve spring is compressed squarely or damage to the
valve stem may occur.
5. Apply sufficient pressure to Tooling (B) in order to remove valve keepers (3). Do not
compress the spring so that valve spring retainer (4) touches valve stem seal (6).
6. Slowly release the pressure on Tooling (B).
7. Remove valve spring retainer (4). Remove valve spring (5). Remove valve (2).
8. Use Tooling (C) in order to remove valve stem seal (6).
3/6
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 9. Repeat Steps 4 through 7 for the remaining valves.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 8S-6691 Cylinder Head Repair Stand 1
B 9U-6195 Valve Spring Compressor Gp 1
D 312-8755 Valve Stem Seal Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean all components of the cylinder head assembly. Ensure that all ports, all coolant
passages, and all lubrication passages in the cylinder head are free from debris. Follow
Steps 1.a through 1.d in order to inspect the components of the cylinder head assembly.
Replace any components that are worn or damaged.
a. Inspect the cylinder head for wear and for damage. Refer to Testing and Adjusting,
"Cylinder Head Inspect".
b. Inspect the valve seats for wear and for damage. Refer to Specifications, "Cylinder
Head Valves" for further information.
c. Inspect the valve guides for wear and for damage. Refer to Specifications, "Cylinder
Head Valves" and Testing and Adjusting, "Valve Guide - Inspect" for further
information.
d. Inspect the valves for wear and for damage. Refer to Specifications, "Cylinder Head
Valves ".
e. Inspect valve springs (5) for damage and for the correct length. Refer to
Specifications, "Cylinder Head Valves ".
4/6
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 4 g01376184
Illustration 5 g01376926
2. Lubricate the stem of valve (2) with clean engine oil. Install valve (2) in the appropriate
position in the cylinder head.
3. The outer face of the valve guides must be clean and dry before installing the valve stem
seal (6). Use Tooling (C) in order to install new valve stem seal (6) onto the valve guide.
4. Install valve spring (5) onto the cylinder head. Position valve spring retainer (4) on valve
spring (5).
5. Install Tooling (B) in the appropriate position on cylinder head (1) in order to compress
valve spring (5).
Improper assembly of parts that are spring loaded can cause bodily
injury.
5/6
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
6. Apply sufficient pressure to Tooling (B) in order to install valve keepers (3). Do not
compress spring (5) so that valve spring retainer (4) touches valve stem seal (6).
7. Carefully release the pressure on Tooling (B).
8. Repeat Steps 2 through 7 for the remaining valves.
End By:
a. Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Aug 21 22:04:42 UTC+0800 2020
6/6
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR GTF
Configuration: 323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i04625003
Inlet and Exhaust Valve Guides - Remove and Install
SMCS - 1104-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 384-8861 Valve Guide Remover 1
B 138-7573 Link Bracket 4
C 1U-9200 Lever Puller Hoist 1
D 8S-6691 Cylinder Head Repair Stand 1
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
B. Remove the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injector - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: Refer to Special Instructions, SMHS7953-00, "Use of Valve Seat Insert Puller Group" to
aid with the removal of the inlet and exhaust valve seats.
Illustration 1 g01377064
1. Attach Tooling (B) , Tooling (C) , and a suitable lifting device to cylinder head (1) . Use
Tooling (B) , Tooling (C) , and the suitable lifting device in order to turn over cylinder head
(1) by 180° onto Tooling (D) .
2/4
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 2 g01377121
2. Use Tooling (A) in order to remove valve guides (2) (not shown).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
E 384-8862 Valve Guide Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
3/4
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 3 g01377130
1. Lubricate the outside of valve guides (2) (not shown) with clean engine oil.
2. Use Tooling (E) in order to install new valve guides (2) . Install valve guide (2) so that
valve guide (2) protrudes 16.000 mm (0.6299 inch) above Surface (X) of cylinder head (1) .
End By:
a. Install the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injector - Install".
b. Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and Exhaust
Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Aug 21 22:05:41 UTC+0800 2020
4/4
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR GTF
Configuration: 323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i04625001
Inlet and Exhaust Valve Seat Inserts - Remove and Install
SMCS - 1103-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
166-7441 Valve Seat Extractor Tool 1
6V-4194 Valve Seat Extractor (1)
1
6V-4196 Valve Seat Extractor (1)
1
B 138-7573 Link Bracket 4
C 1U-9200 Lever Puller Hoist 1
D 8S-6691 Cylinder Head Repair Stand 1
( 1 )
Component of the Valve Seat Extractor Tool Group.
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
B. Remove the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injectors - Remove".
NOTICE
Keep all parts clean from contaminants.
1/5
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Contaminants may cause rapid wear and shortened component life.
Note: Refer to Special Instructions, SMHS7953-00, "Use of Valve Seat Insert Puller Group" to
aid with the removal of the inlet and exhaust valve seats.
Illustration 1 g01377064
1. Attach Tooling (B ) , Tooling (C) , and a suitable lifting device to cylinder head (1) . Use
Tooling (B ) , Tooling (C) , and the suitable lifting device in order to turn over cylinder head
(1) by 180° onto Tooling (D) .
2/5
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 2 g01376571
2. Use the valve seat grinder of Tooling (A) in order to notch the valve seat.
Illustration 3 g01376578
3. Use the valve seat extractor of Tooling (A) to remove the inlet and exhaust valve seats.
4. Clean the valve seat in the cylinder head. Remove any rough areas from the valve seat in the
cylinder head.
5. Repeat Steps 2 through 4 for the remaining inlet valve seat inserts and exhaust valve seat
inserts.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
E 384-8859 Valve Seat Installer 1
F 384-8860 Valve Seat Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
3/5
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 4 g01377071
Typical Example
1. Lower the temperature of the new inlet valve seat inserts (2) . Use Tooling (E) in order to
install a new inlet valve seat insert (2) (not shown) in the cylinder head.
Illustration 5 g01376588
Typical Example
2. Lower the temperature of new exhaust valve seat inserts (3) . Use Tooling (E) and Tooling
(F) in order to install the new exhaust valve seat insert (3) (not shown) in the cylinder head.
Note: The temperature of exhaust valve seat insert (3) is lowered in order to ease the
installation of exhaust valve seat insert (3) .
3. Repeat Step 1 and 2 for the remaining inlet valve seat inserts and exhaust valve seat inserts.
End By:
a. Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and Exhaust
Valves - Remove and Install".
b. Install the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injectors - Install".
4/5
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR GTF
Configuration: 323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02746253
Engine Oil Cooler - Remove
SMCS - 1378-011
Removal Procedure
Start By:
a. Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump
- Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/2
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 1 g01375410
1. Disconnect harness assembly (1).
2. Remove bolts (2) and remove engine oil cooler (3). Remove gasket (4) (not shown) from the
engine cylinder block.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Aug 21 22:07:39 UTC+0800 2020
2/2
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR GTF
Configuration: 323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02746254
Engine Oil Cooler - Disassemble
SMCS - 1378-015
Disassembly Procedure
Start By:
a. Remove the engine oil cooler. Refer to Disassembly and Assembly, "Engine Oil Cooler - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior of the
components should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism. Precision components can be damaged by contaminants or by dirt. Perform disassembly
procedures on a clean work surface. Keep components covered and protected at all times.
1/2
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 1 g01375411
1. Remove bolts (9) and the washers. Remove cover (8) and gasket (7).
2. Remove nuts (5) and the washers from engine oil cooler cover (4). Remove nuts (6) and the washers
from engine oil cooler cover (4).
3. Remove engine oil cooler core (2) from engine oil cooler cover (4). Remove gaskets (1) and (3).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Aug 21 22:08:39 UTC+0800 2020
2/2
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR GTF
Configuration: 323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02746255
Engine Oil Cooler - Assemble
SMCS - 1378-016
Assembly Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning fluid.
Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts
which may cause trouble. Inspect all parts. If any parts are worn or damaged, use new parts for
replacement. Dirt and other contaminants can damage the precision component. Perform assembly
procedures on a clean work surface. Keep components covered and protected at all times.
Note: Check the gaskets for damage. Replace the components, if necessary.
1/2
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 1 g01375411
1. Install gaskets (3) and (1) to engine oil cooler core (2). Position engine oil cooler core (2) to engine
oil cooler cover (4).
2. Install the washers and nuts (6). Install the washers and nuts (5).
3. Install gasket (7) and position cover (8). Install the washers and bolts (9).
End By:
a. Install the engine oil cooler. Refer to Disassembly and Assembly, "Engine Oil Cooler - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Aug 21 22:09:38 UTC+0800 2020
2/2
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR GTF
Configuration: 323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02746256
Engine Oil Cooler - Install
SMCS - 1378-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Check the gaskets for wear or for damage. Replace the components, if necessary.
Illustration 1 g01375410
1. Install gasket (4) (not shown). Position engine oil cooler (3) to the engine block. Install bolts
(2).
1/2
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. 2. Connect harness assembly (1).
End By:
a. Install the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump -
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Aug 21 22:10:37 UTC+0800 2020
2/2
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR GTF
Configuration: 323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02751808
Engine Oil Relief Valve - Remove and Install
SMCS - 1315-010
Removal Procedure
Start By:
a. Remove the electronic control module. Refer to Disassembly and Assembly, "Electronic
Control Module - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01377673
1/2
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. 1. Remove engine oil relief valve (1).
2. Remove gasket (2) (not shown). Discard gasket (2).
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01377673
1. Install a new gasket (2) (not shown).
2. Install engine oil relief valve (1). Tighten engine oil relief valve (1) to a torque of
49 ± 5 N·m (36 ± 4 lb ft).
End By:
a. Install the electronic control module. Refer to Disassembly and Assembly, "Electronic
Control Module - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Aug 21 22:11:36 UTC+0800 2020
2/2
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR GTF
Configuration: 323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02751881
Engine Oil Bypass Valve - Remove and Install
SMCS - 1306-010-BV
Removal Procedure
Start By:
a. Remove the oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01377713
1. Remove engine oil bypass valve (1). Remove gasket (2) (not shown). Discard gasket (2).
1/2
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...