- The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a C6.4 engine.
- Key steps include using tooling to compress valve springs and remove components, cleaning parts, lubricating new components, and ensuring proper protrusion of installed parts.
- Safety notices warn of risks such as being struck by released spring forces and containing fluids during inspection and repair.
Caterpillar cat 323 d l excavator (prefix gtf) service repair manual (gtf0000...fjjsekmsmmes
This document provides instructions for removing and installing inlet and exhaust valve seats in a C6.4 engine. It describes using various tools to remove the valves, valve guides, and valve seat inserts from the cylinder head. It also details how to clean, inspect, and lubricate components before reinstalling the valve seat inserts, guides, and valves in the proper order and orientation. Protective equipment is recommended to safely compress springs during the process.
Caterpillar cat 311 d lrr excavator (prefix cla) service repair manual (cla00...dkdmidkkdk
This document provides instructions for removing and installing inlet and exhaust valves and valve guides on a C4.2 engine. The procedure involves using various tools to compress springs, remove components in the proper order, clean parts, and lubricate components before installation. Precautions are outlined to prevent injury and ensure proper assembly.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing valves, valve guides, and the engine oil cooler. Precautions are outlined to prevent contamination and contain fluids.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing valves, valve guides, and installing new components. The document also describes draining coolant and removing bolts to take off the engine oil cooler.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
Caterpillar cat 311 d lrr excavator (prefix cla) service repair manual (cla00...fjjsekkdmme
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
Caterpillar cat 323 d l excavator (prefix gtf) service repair manual (gtf0000...fjjsekmsmmes
This document provides instructions for removing and installing inlet and exhaust valve seats in a C6.4 engine. It describes using various tools to remove the valves, valve guides, and valve seat inserts from the cylinder head. It also details how to clean, inspect, and lubricate components before reinstalling the valve seat inserts, guides, and valves in the proper order and orientation. Protective equipment is recommended to safely compress springs during the process.
Caterpillar cat 311 d lrr excavator (prefix cla) service repair manual (cla00...dkdmidkkdk
This document provides instructions for removing and installing inlet and exhaust valves and valve guides on a C4.2 engine. The procedure involves using various tools to compress springs, remove components in the proper order, clean parts, and lubricate components before installation. Precautions are outlined to prevent injury and ensure proper assembly.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing valves, valve guides, and the engine oil cooler. Precautions are outlined to prevent contamination and contain fluids.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing valves, valve guides, and installing new components. The document also describes draining coolant and removing bolts to take off the engine oil cooler.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
Caterpillar cat 311 d lrr excavator (prefix cla) service repair manual (cla00...fjjsekkdmme
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
Caterpillar cat 311 d lrr excavator (prefix cla) service repair manual (cla00...fjjskekmsemm
This document provides the procedure for removing and installing inlet and exhaust valves and valve guides on a Caterpillar C4.2 engine. The procedure involves using various tools to compress springs, remove components in the proper order, clean parts, and inspect for wear. Valves, guides, seals and other components are then reinstalled in the reverse order, taking care to lubricate parts and set components to the correct specifications.
Caterpillar cat 311 d lrr excavator (prefix cla) service repair manual (cla00...fjsekdmmeed
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
1. The document provides instructions for removing and installing inlet and exhaust valves and valve guides on a Caterpillar C4.2 engine.
2. The removal procedure includes using various tools to compress the valve springs, remove the valve keepers and other components, and extract the valves and valve guides.
3. The installation procedure specifies cleaning and lubricating the components, and using tools to reinstall the valve guides at the proper height and compress the springs to reinstall the valves and associated parts.
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and an engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to disassemble and remove the components, cleaning requirements, and installation procedures.
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and an engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to disassemble components like removing valve springs and stem seals, and installing new valve stem seals. Precautions are outlined to keep parts clean and contain fluids during the repair work.
Caterpillar cat 323 d excavator (prefix wgc) service repair manual (wgc00001 ...idkkdmmdd
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C6.4 engine. It outlines the required tools and safety precautions. The procedure involves using a valve spring compressor tool to compress the valve spring and remove the retainer, spring, and valve components. Reinstallation follows the reverse order, ensuring parts are clean and applying the proper pressure with the compressor tool. The summary is intended only to convey the main focus and steps involved, not to replace reading the full instructions.
Caterpillar cat 323 d l excavator (prefix wgc) service repair manual (wgc0000...idkkmdmd
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C6.4 engine. It outlines the required tools and safety precautions. The procedure involves using a valve spring compressor tool to compress the valve spring and remove the retainer, spring, and valve components. Reinstallation follows the reverse order, ensuring parts are clean and applying the proper pressure with the compressor tool. The summary is intended only to convey the main focus and steps involved, not serve as a replacement for the full instructions.
Caterpillar cat 323 d l excavator (prefix wgc) service repair manual (wgc0000...dhjfjkmmmde
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C6.4 engine. It describes the required tools and safety precautions. The procedure involves using a valve spring compressor tool to compress the valve spring and remove the retainer, spring, and valve keeper. Installation is the reverse process of cleaning components and lubricating the valve stem before reinstalling the valve keeper, spring, and retainer while compressing the spring with the tool.
Caterpillar cat 323 d excavator (prefix wgc) service repair manual (wgc00001 ...fhsjekkdkem
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C6.4 engine. It describes the required tools and safety precautions. The procedure involves using a valve spring compressor tool to compress the valve spring and remove the retainer, spring, and valve keeper. The process is then reversed to install the new parts, ensuring the valve stem seal is installed correctly. Similar instructions are provided for removing and installing the valve guides.
Caterpillar cat 323 d excavator (prefix wgc) service repair manual (wgc00001 ...fhsejkdkmem
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C6.4 engine. It describes the required tools and safety precautions. The procedure involves using a valve spring compressor tool to compress the valve spring and remove the retainer, spring, and valve keeper. Installation is the reverse process of cleaning components and lubricating the valve stem before reinstalling the valve keeper, spring, and retainer while compressing the spring with the tool.
1. The document provides instructions for removing and installing the flywheel and crankshaft rear seal on a C7.1 engine that powers a 323 excavator.
2. To remove the flywheel, bolts must first be removed and guide studs installed before lifting the flywheel off using a lifting device. The ring gear can then be removed by heating and pressing it off.
3. Flywheel installation requires cleaning and inspecting components, heating and pressing the ring gear if replaced, and torquing bolts with the flywheel secured to prevent rotation.
4. Crankshaft rear seal removal requires removing screws using a Torx socket after removing the flywheel housing. The sealed assembly
Caterpillar Cat 326D2 (Prefix KGY) Service Repair Manual (KGY00001 and up).pdfkm7seydwuhdw
This document provides instructions for disassembling and assembling the travel motor of a 326D2 excavator. It lists the required tools and gives step-by-step procedures to remove and install various components of the travel motor such as the head, bearings, brake piston, seals, and housing covers. Special care must be taken when handling springs or installing seals to avoid injury. All components must be cleaned thoroughly before assembly and lubricated with oil during reassembly.
Crown TSP6000 Series Turret Order Picker Parts Catalogue Manual.pdfkm7seydwuhdw
This document is a parts manual for the power unit of a TSP6000 series truck. It contains 30 numbered parts that make up the power unit, including the power unit housing, doors, covers, screws, nuts, and other minor components. Next to each numbered part is the corresponding part number and a brief description. The parts are organized by their location and function within the power unit.
The document provides instructions for removing and installing engine components, including:
- Removing and installing inlet and exhaust valves, which requires using a valve spring compressor tool
- Removing and installing inlet and exhaust valve guides using driver tools
- Removing and installing inlet and exhaust valve seat inserts, which requires a valve seat extractor tool kit
- Removing the engine oil filter base using a strap wrench tool
The procedures describe the required tools and provide illustrations of the component removal and installation steps. Safety notices are included to keep parts clean and contain fluids properly during maintenance.
Crown WAV50 Work Assit Vehicle Parts Catalogue Manual.pdfkm7seydwuhdw
This parts manual provides exploded diagrams and part lists for the WAV 50 Series order number 812718-006. It includes 10 sections covering the chassis front and rear, axle, hydraulic unit, drive unit, electrical parts, mast/lift structure, cylinder, cabin/platform, miscellaneous service information, and labels/decals. The document provides overview diagrams and indexes that list each part number, name, and quantity required to service or repair the truck.
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of a 324E LN excavator.
2. It details 27 steps to disassemble components like the head, brake piston, rotating assembly, and seals.
3. The 28 steps for assembly instruct to reinstall these components in reverse order and note proper alignment of parts, use of lubrication and tools.
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove the flywheel housing bolts and separate the housing from the cylinder block.
3) Installing a new gasket and oil seal before reinstalling the housing and torquing the bolts.
4) Reinstalling the flywheel and electric starting motor after installing the flywheel housing.
Crown ST3000 Series Forklift Service Repair Manual.pdfkm7seydwuhdw
This document provides a service manual for the ST3000 series truck. It contains sections covering safety, introduction/use of the manual, lubrication and adjustment procedures, hydraulics, the drive unit, and electrical systems. The manual includes information on component access, recommended lubricants, maintenance schedules, hydraulic and electrical symbols, and troubleshooting charts to assist with repairs.
Crown SC3016 Forklift Parts Catalogue Manual.pdfkm7seydwuhdw
This document is a parts manual that contains a table of contents listing replacement parts for an SC3000 series machine. The table of contents includes over 50 part descriptions organized into 7 sections related to the power unit, hydraulic system, drive unit, electrical system, brakes, steering, and mast/lift structure. Each part listing includes the part's page number and identification number for reference in the manual.
Crown SC3013 Forklift Parts Catalogue Manual.pdfkm7seydwuhdw
This document is a parts manual for a SC3000 series truck. It contains:
- A table of contents listing the document sections and part descriptions with corresponding page numbers and identification numbers.
- A section on safety information and general maintenance guidelines.
- An introduction providing information on operating instructions, service training, and part ordering.
- The document is organized into sections covering the truck's power unit, hydraulic, drive, electrical, brake, steering, mast/lift, cylinder, and miscellaneous parts. Each section lists the relevant parts with identification numbers to order replacements.
This document provides instructions for disassembling the final drive, travel motor, and other components of an excavator model 312D2. It lists the required tools and gives step-by-step procedures to remove parts like sprockets, valves, gears, plates, and seals. Safety warnings are provided to release pressures and springs carefully due to risk of injury from propelled parts. Detailed illustrations accompany each step to ensure correct reassembly.
This document provides instructions to disassemble a final drive on a 325D MH EXCAVATOR. It outlines 31 steps to remove components like the cover, gears, carrier assemblies, housing and seals. Special tools are required and cleanliness is important to prevent dirt from entering during reassembly. Weights of components are provided to assist with removal.
More Related Content
Similar to Caterpillar Cat 323D L Excavator (Prefix GTF) Service Repair Manual (GTF00001 and up).pdf
Caterpillar cat 311 d lrr excavator (prefix cla) service repair manual (cla00...fjjskekmsemm
This document provides the procedure for removing and installing inlet and exhaust valves and valve guides on a Caterpillar C4.2 engine. The procedure involves using various tools to compress springs, remove components in the proper order, clean parts, and inspect for wear. Valves, guides, seals and other components are then reinstalled in the reverse order, taking care to lubricate parts and set components to the correct specifications.
Caterpillar cat 311 d lrr excavator (prefix cla) service repair manual (cla00...fjsekdmmeed
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
1. The document provides instructions for removing and installing inlet and exhaust valves and valve guides on a Caterpillar C4.2 engine.
2. The removal procedure includes using various tools to compress the valve springs, remove the valve keepers and other components, and extract the valves and valve guides.
3. The installation procedure specifies cleaning and lubricating the components, and using tools to reinstall the valve guides at the proper height and compress the springs to reinstall the valves and associated parts.
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and an engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to disassemble and remove the components, cleaning requirements, and installation procedures.
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and an engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to disassemble components like removing valve springs and stem seals, and installing new valve stem seals. Precautions are outlined to keep parts clean and contain fluids during the repair work.
Caterpillar cat 323 d excavator (prefix wgc) service repair manual (wgc00001 ...idkkdmmdd
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C6.4 engine. It outlines the required tools and safety precautions. The procedure involves using a valve spring compressor tool to compress the valve spring and remove the retainer, spring, and valve components. Reinstallation follows the reverse order, ensuring parts are clean and applying the proper pressure with the compressor tool. The summary is intended only to convey the main focus and steps involved, not to replace reading the full instructions.
Caterpillar cat 323 d l excavator (prefix wgc) service repair manual (wgc0000...idkkmdmd
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C6.4 engine. It outlines the required tools and safety precautions. The procedure involves using a valve spring compressor tool to compress the valve spring and remove the retainer, spring, and valve components. Reinstallation follows the reverse order, ensuring parts are clean and applying the proper pressure with the compressor tool. The summary is intended only to convey the main focus and steps involved, not serve as a replacement for the full instructions.
Caterpillar cat 323 d l excavator (prefix wgc) service repair manual (wgc0000...dhjfjkmmmde
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C6.4 engine. It describes the required tools and safety precautions. The procedure involves using a valve spring compressor tool to compress the valve spring and remove the retainer, spring, and valve keeper. Installation is the reverse process of cleaning components and lubricating the valve stem before reinstalling the valve keeper, spring, and retainer while compressing the spring with the tool.
Caterpillar cat 323 d excavator (prefix wgc) service repair manual (wgc00001 ...fhsjekkdkem
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C6.4 engine. It describes the required tools and safety precautions. The procedure involves using a valve spring compressor tool to compress the valve spring and remove the retainer, spring, and valve keeper. The process is then reversed to install the new parts, ensuring the valve stem seal is installed correctly. Similar instructions are provided for removing and installing the valve guides.
Caterpillar cat 323 d excavator (prefix wgc) service repair manual (wgc00001 ...fhsejkdkmem
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C6.4 engine. It describes the required tools and safety precautions. The procedure involves using a valve spring compressor tool to compress the valve spring and remove the retainer, spring, and valve keeper. Installation is the reverse process of cleaning components and lubricating the valve stem before reinstalling the valve keeper, spring, and retainer while compressing the spring with the tool.
Similar to Caterpillar Cat 323D L Excavator (Prefix GTF) Service Repair Manual (GTF00001 and up).pdf (10)
1. The document provides instructions for removing and installing the flywheel and crankshaft rear seal on a C7.1 engine that powers a 323 excavator.
2. To remove the flywheel, bolts must first be removed and guide studs installed before lifting the flywheel off using a lifting device. The ring gear can then be removed by heating and pressing it off.
3. Flywheel installation requires cleaning and inspecting components, heating and pressing the ring gear if replaced, and torquing bolts with the flywheel secured to prevent rotation.
4. Crankshaft rear seal removal requires removing screws using a Torx socket after removing the flywheel housing. The sealed assembly
Caterpillar Cat 326D2 (Prefix KGY) Service Repair Manual (KGY00001 and up).pdfkm7seydwuhdw
This document provides instructions for disassembling and assembling the travel motor of a 326D2 excavator. It lists the required tools and gives step-by-step procedures to remove and install various components of the travel motor such as the head, bearings, brake piston, seals, and housing covers. Special care must be taken when handling springs or installing seals to avoid injury. All components must be cleaned thoroughly before assembly and lubricated with oil during reassembly.
Crown TSP6000 Series Turret Order Picker Parts Catalogue Manual.pdfkm7seydwuhdw
This document is a parts manual for the power unit of a TSP6000 series truck. It contains 30 numbered parts that make up the power unit, including the power unit housing, doors, covers, screws, nuts, and other minor components. Next to each numbered part is the corresponding part number and a brief description. The parts are organized by their location and function within the power unit.
The document provides instructions for removing and installing engine components, including:
- Removing and installing inlet and exhaust valves, which requires using a valve spring compressor tool
- Removing and installing inlet and exhaust valve guides using driver tools
- Removing and installing inlet and exhaust valve seat inserts, which requires a valve seat extractor tool kit
- Removing the engine oil filter base using a strap wrench tool
The procedures describe the required tools and provide illustrations of the component removal and installation steps. Safety notices are included to keep parts clean and contain fluids properly during maintenance.
Crown WAV50 Work Assit Vehicle Parts Catalogue Manual.pdfkm7seydwuhdw
This parts manual provides exploded diagrams and part lists for the WAV 50 Series order number 812718-006. It includes 10 sections covering the chassis front and rear, axle, hydraulic unit, drive unit, electrical parts, mast/lift structure, cylinder, cabin/platform, miscellaneous service information, and labels/decals. The document provides overview diagrams and indexes that list each part number, name, and quantity required to service or repair the truck.
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of a 324E LN excavator.
2. It details 27 steps to disassemble components like the head, brake piston, rotating assembly, and seals.
3. The 28 steps for assembly instruct to reinstall these components in reverse order and note proper alignment of parts, use of lubrication and tools.
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove the flywheel housing bolts and separate the housing from the cylinder block.
3) Installing a new gasket and oil seal before reinstalling the housing and torquing the bolts.
4) Reinstalling the flywheel and electric starting motor after installing the flywheel housing.
Crown ST3000 Series Forklift Service Repair Manual.pdfkm7seydwuhdw
This document provides a service manual for the ST3000 series truck. It contains sections covering safety, introduction/use of the manual, lubrication and adjustment procedures, hydraulics, the drive unit, and electrical systems. The manual includes information on component access, recommended lubricants, maintenance schedules, hydraulic and electrical symbols, and troubleshooting charts to assist with repairs.
Crown SC3016 Forklift Parts Catalogue Manual.pdfkm7seydwuhdw
This document is a parts manual that contains a table of contents listing replacement parts for an SC3000 series machine. The table of contents includes over 50 part descriptions organized into 7 sections related to the power unit, hydraulic system, drive unit, electrical system, brakes, steering, and mast/lift structure. Each part listing includes the part's page number and identification number for reference in the manual.
Crown SC3013 Forklift Parts Catalogue Manual.pdfkm7seydwuhdw
This document is a parts manual for a SC3000 series truck. It contains:
- A table of contents listing the document sections and part descriptions with corresponding page numbers and identification numbers.
- A section on safety information and general maintenance guidelines.
- An introduction providing information on operating instructions, service training, and part ordering.
- The document is organized into sections covering the truck's power unit, hydraulic, drive, electrical, brake, steering, mast/lift, cylinder, and miscellaneous parts. Each section lists the relevant parts with identification numbers to order replacements.
This document provides instructions for disassembling the final drive, travel motor, and other components of an excavator model 312D2. It lists the required tools and gives step-by-step procedures to remove parts like sprockets, valves, gears, plates, and seals. Safety warnings are provided to release pressures and springs carefully due to risk of injury from propelled parts. Detailed illustrations accompany each step to ensure correct reassembly.
This document provides instructions to disassemble a final drive on a 325D MH EXCAVATOR. It outlines 31 steps to remove components like the cover, gears, carrier assemblies, housing and seals. Special tools are required and cleanliness is important to prevent dirt from entering during reassembly. Weights of components are provided to assist with removal.
This document provides instructions for disassembling components of an excavator including the final drive, travel motor, counterbalance valve, and barrel assembly. It lists required tools and outlines multi-step procedures involving removing fittings, draining fluids, loosening bolts, using pullers to remove bearings and seals, and carefully disassembling internal parts while keeping components in order for reassembly. Safety notices warn of risks such as fluid pressure, heavy lifting, and released spring forces.
The document provides instructions for installing and removing several engine components on a Caterpillar 312D excavator including:
1. Installing the flywheel which requires heating the ring gear, pressing it onto the flywheel, and securing it with bolts.
2. Removing and installing the crankshaft rear seal using tools like a slide hammer and seal distorter.
3. Installing the crankshaft rear seal which involves cleaning surfaces, applying retaining compound, and using an installer tool.
4. Removing and installing the flywheel housing which requires lifting tools and removing/installing bolts, seals and gaskets.
The document provides instructions for disassembling and assembling the swing drive of a 312C excavator. It describes removing over 20 individual parts in 16 steps for disassembly, including the sun gear, carrier assembly, ring gear, planetary gears, shafts, bearings, and housing components. Reassembly involves installing the same parts in the reverse order over 17 steps, applying sealant and fasteners, and noting torque specifications. The overall process handles each part with care to prevent contamination and properly position components using lifting devices and presses.
The document provides the disassembly procedure for a travel motor in 27 steps. It begins by removing the travel motor and cleaning it. Key steps include removing the head, brake piston, friction plates, and barrel assembly. Small components like seals, springs, and races are also removed. Precise identification marks are needed to ensure correct reassembly of small parts and piston shoe assemblies in their original locations. Tools required for the disassembly are also listed.
Caterpillar Cat 324E L Excavator (Prefix TLF) Service Repair Manual (TLF00001...km7seydwuhdw
This document provides instructions for disassembling and assembling the travel motor of 324E L and 324E LN Excavator models. It lists the required tools and parts and provides step-by-step instructions and illustrations for removing and installing components like the motor head, brake piston, rotating assembly, bearings, seals, and more. Precautions are included to properly handle springs and ensure correct positioning of parts.
Caterpillar Cat 312D L Excavator (Prefix HCW) Service Repair Manual (HCW00001...km7seydwuhdw
This document provides instructions for installing the crankshaft in a Caterpillar 312D or 312D L excavator. It involves the following steps:
1. Install the thrust washer and upper halves of the main bearings in the cylinder block. Lubricate and position the crankshaft onto the bearings.
2. Install the lower main bearings onto the bearing caps and rear cap. Lubricate and install seals in the rear cap grooves.
3. Install the bearing caps and tighten the bolts to specification. Check crankshaft end play and install the connecting rods, pistons, and remaining components.
This document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator, including:
- Removing and installing the flywheel, which requires the use of lifting tools and bolts are tightened to a specified torque.
- Removing the crankshaft rear seal using drilling and hammering tools, taking care not to damage surfaces.
- Installing the rear seal using a seal installer tool.
- Procedures for removing and installing the flywheel housing and vibration damper/pulley that involve cleaning surfaces, applying sealant, and tightening bolts.
Caterpillar Cat 312D L Excavator (Prefix KES) Service Repair Manual (KES00001...km7seydwuhdw
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove the flywheel housing bolts and separate the housing from the cylinder block.
3) Installing a new gasket and oil seal before reinstalling the flywheel housing with bolts and reattaching the flywheel and starting motor.
Leadership Ambassador club Adventist modulekakomaeric00
Aims to equip people who aspire to become leaders with good qualities,and with Christian values and morals as per Biblical teachings.The you who aspire to be leaders should first read and understand what the ambassador module for leadership says about leadership and marry that to what the bible says.Christians sh
Job Finding Apps Everything You Need to Know in 2024SnapJob
SnapJob is revolutionizing the way people connect with work opportunities and find talented professionals for their projects. Find your dream job with ease using the best job finding apps. Discover top-rated apps that connect you with employers, provide personalized job recommendations, and streamline the application process. Explore features, ratings, and reviews to find the app that suits your needs and helps you land your next opportunity.
Resumes, Cover Letters, and Applying OnlineBruce Bennett
This webinar showcases resume styles and the elements that go into building your resume. Every job application requires unique skills, and this session will show you how to improve your resume to match the jobs to which you are applying. Additionally, we will discuss cover letters and learn about ideas to include. Every job application requires unique skills so learn ways to give you the best chance of success when applying for a new position. Learn how to take advantage of all the features when uploading a job application to a company’s applicant tracking system.
A Guide to a Winning Interview June 2024Bruce Bennett
This webinar is an in-depth review of the interview process. Preparation is a key element to acing an interview. Learn the best approaches from the initial phone screen to the face-to-face meeting with the hiring manager. You will hear great answers to several standard questions, including the dreaded “Tell Me About Yourself”.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR GTF
Configuration: 323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i06051426
Inlet and Exhaust Valves - Remove and Install
SMCS - 1105-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8S-6691 Cylinder Head Repair Stand 1
B 9U-6195 Valve Spring Compressor Gp 1
C 5P-1720 Seal Pick 1
Start By:
a. Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Note the location and orientation of all components for assembly purposes.
1. Clean the bottom face of the cylinder head. Check the depth of the valves below the face of
the cylinder head before the valve springs are removed. Refer to Specifications, "Cylinder
Head Valves" for the correct dimensions.
1/6
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. 2. Place a temporary identification mark on the heads of the valves in order to identify the
correct position.
Illustration 1 g01376164
3. Use a suitable lifting device in order to position cylinder head (1) onto Tooling (A) with the
valve springs upward. The weight of cylinder head (1) is approximately 113 kg (250 lb).
Note: Ensure that cylinder head (1) is kept on a clean, soft surface in order to prevent
damage to the machined face.
Illustration 2 g01376174
2/6
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g01376184
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
4. Install Tooling (B) on cylinder head (1) in order to compress valve spring (5).
NOTICE
Ensure that the valve spring is compressed squarely or damage to the
valve stem may occur.
5. Apply sufficient pressure to Tooling (B) in order to remove valve keepers (3). Do not
compress the spring so that valve spring retainer (4) touches valve stem seal (6).
6. Slowly release the pressure on Tooling (B).
7. Remove valve spring retainer (4). Remove valve spring (5). Remove valve (2).
8. Use Tooling (C) in order to remove valve stem seal (6).
3/6
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 9. Repeat Steps 4 through 7 for the remaining valves.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 8S-6691 Cylinder Head Repair Stand 1
B 9U-6195 Valve Spring Compressor Gp 1
D 312-8755 Valve Stem Seal Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean all components of the cylinder head assembly. Ensure that all ports, all coolant
passages, and all lubrication passages in the cylinder head are free from debris. Follow
Steps 1.a through 1.d in order to inspect the components of the cylinder head assembly.
Replace any components that are worn or damaged.
a. Inspect the cylinder head for wear and for damage. Refer to Testing and Adjusting,
"Cylinder Head Inspect".
b. Inspect the valve seats for wear and for damage. Refer to Specifications, "Cylinder
Head Valves" for further information.
c. Inspect the valve guides for wear and for damage. Refer to Specifications, "Cylinder
Head Valves" and Testing and Adjusting, "Valve Guide - Inspect" for further
information.
d. Inspect the valves for wear and for damage. Refer to Specifications, "Cylinder Head
Valves ".
e. Inspect valve springs (5) for damage and for the correct length. Refer to
Specifications, "Cylinder Head Valves ".
4/6
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 4 g01376184
Illustration 5 g01376926
2. Lubricate the stem of valve (2) with clean engine oil. Install valve (2) in the appropriate
position in the cylinder head.
3. The outer face of the valve guides must be clean and dry before installing the valve stem
seal (6). Use Tooling (C) in order to install new valve stem seal (6) onto the valve guide.
4. Install valve spring (5) onto the cylinder head. Position valve spring retainer (4) on valve
spring (5).
5. Install Tooling (B) in the appropriate position on cylinder head (1) in order to compress
valve spring (5).
Improper assembly of parts that are spring loaded can cause bodily
injury.
5/6
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
6. Apply sufficient pressure to Tooling (B) in order to install valve keepers (3). Do not
compress spring (5) so that valve spring retainer (4) touches valve stem seal (6).
7. Carefully release the pressure on Tooling (B).
8. Repeat Steps 2 through 7 for the remaining valves.
End By:
a. Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Aug 21 22:04:42 UTC+0800 2020
6/6
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR GTF
Configuration: 323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i04625003
Inlet and Exhaust Valve Guides - Remove and Install
SMCS - 1104-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 384-8861 Valve Guide Remover 1
B 138-7573 Link Bracket 4
C 1U-9200 Lever Puller Hoist 1
D 8S-6691 Cylinder Head Repair Stand 1
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
B. Remove the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injector - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: Refer to Special Instructions, SMHS7953-00, "Use of Valve Seat Insert Puller Group" to
aid with the removal of the inlet and exhaust valve seats.
Illustration 1 g01377064
1. Attach Tooling (B) , Tooling (C) , and a suitable lifting device to cylinder head (1) . Use
Tooling (B) , Tooling (C) , and the suitable lifting device in order to turn over cylinder head
(1) by 180° onto Tooling (D) .
2/4
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 2 g01377121
2. Use Tooling (A) in order to remove valve guides (2) (not shown).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
E 384-8862 Valve Guide Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
3/4
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 3 g01377130
1. Lubricate the outside of valve guides (2) (not shown) with clean engine oil.
2. Use Tooling (E) in order to install new valve guides (2) . Install valve guide (2) so that
valve guide (2) protrudes 16.000 mm (0.6299 inch) above Surface (X) of cylinder head (1) .
End By:
a. Install the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injector - Install".
b. Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and Exhaust
Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Aug 21 22:05:41 UTC+0800 2020
4/4
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR GTF
Configuration: 323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i04625001
Inlet and Exhaust Valve Seat Inserts - Remove and Install
SMCS - 1103-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
166-7441 Valve Seat Extractor Tool 1
6V-4194 Valve Seat Extractor (1)
1
6V-4196 Valve Seat Extractor (1)
1
B 138-7573 Link Bracket 4
C 1U-9200 Lever Puller Hoist 1
D 8S-6691 Cylinder Head Repair Stand 1
( 1 )
Component of the Valve Seat Extractor Tool Group.
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
B. Remove the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injectors - Remove".
NOTICE
Keep all parts clean from contaminants.
1/5
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Contaminants may cause rapid wear and shortened component life.
Note: Refer to Special Instructions, SMHS7953-00, "Use of Valve Seat Insert Puller Group" to
aid with the removal of the inlet and exhaust valve seats.
Illustration 1 g01377064
1. Attach Tooling (B ) , Tooling (C) , and a suitable lifting device to cylinder head (1) . Use
Tooling (B ) , Tooling (C) , and the suitable lifting device in order to turn over cylinder head
(1) by 180° onto Tooling (D) .
2/5
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 2 g01376571
2. Use the valve seat grinder of Tooling (A) in order to notch the valve seat.
Illustration 3 g01376578
3. Use the valve seat extractor of Tooling (A) to remove the inlet and exhaust valve seats.
4. Clean the valve seat in the cylinder head. Remove any rough areas from the valve seat in the
cylinder head.
5. Repeat Steps 2 through 4 for the remaining inlet valve seat inserts and exhaust valve seat
inserts.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
E 384-8859 Valve Seat Installer 1
F 384-8860 Valve Seat Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
3/5
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 4 g01377071
Typical Example
1. Lower the temperature of the new inlet valve seat inserts (2) . Use Tooling (E) in order to
install a new inlet valve seat insert (2) (not shown) in the cylinder head.
Illustration 5 g01376588
Typical Example
2. Lower the temperature of new exhaust valve seat inserts (3) . Use Tooling (E) and Tooling
(F) in order to install the new exhaust valve seat insert (3) (not shown) in the cylinder head.
Note: The temperature of exhaust valve seat insert (3) is lowered in order to ease the
installation of exhaust valve seat insert (3) .
3. Repeat Step 1 and 2 for the remaining inlet valve seat inserts and exhaust valve seat inserts.
End By:
a. Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and Exhaust
Valves - Remove and Install".
b. Install the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injectors - Install".
4/5
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR GTF
Configuration: 323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02746253
Engine Oil Cooler - Remove
SMCS - 1378-011
Removal Procedure
Start By:
a. Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump
- Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/2
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 1 g01375410
1. Disconnect harness assembly (1).
2. Remove bolts (2) and remove engine oil cooler (3). Remove gasket (4) (not shown) from the
engine cylinder block.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Aug 21 22:07:39 UTC+0800 2020
2/2
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR GTF
Configuration: 323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02746254
Engine Oil Cooler - Disassemble
SMCS - 1378-015
Disassembly Procedure
Start By:
a. Remove the engine oil cooler. Refer to Disassembly and Assembly, "Engine Oil Cooler - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior of the
components should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism. Precision components can be damaged by contaminants or by dirt. Perform disassembly
procedures on a clean work surface. Keep components covered and protected at all times.
1/2
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 1 g01375411
1. Remove bolts (9) and the washers. Remove cover (8) and gasket (7).
2. Remove nuts (5) and the washers from engine oil cooler cover (4). Remove nuts (6) and the washers
from engine oil cooler cover (4).
3. Remove engine oil cooler core (2) from engine oil cooler cover (4). Remove gaskets (1) and (3).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Aug 21 22:08:39 UTC+0800 2020
2/2
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR GTF
Configuration: 323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02746255
Engine Oil Cooler - Assemble
SMCS - 1378-016
Assembly Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning fluid.
Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts
which may cause trouble. Inspect all parts. If any parts are worn or damaged, use new parts for
replacement. Dirt and other contaminants can damage the precision component. Perform assembly
procedures on a clean work surface. Keep components covered and protected at all times.
Note: Check the gaskets for damage. Replace the components, if necessary.
1/2
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 1 g01375411
1. Install gaskets (3) and (1) to engine oil cooler core (2). Position engine oil cooler core (2) to engine
oil cooler cover (4).
2. Install the washers and nuts (6). Install the washers and nuts (5).
3. Install gasket (7) and position cover (8). Install the washers and bolts (9).
End By:
a. Install the engine oil cooler. Refer to Disassembly and Assembly, "Engine Oil Cooler - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Aug 21 22:09:38 UTC+0800 2020
2/2
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR GTF
Configuration: 323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02746256
Engine Oil Cooler - Install
SMCS - 1378-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Check the gaskets for wear or for damage. Replace the components, if necessary.
Illustration 1 g01375410
1. Install gasket (4) (not shown). Position engine oil cooler (3) to the engine block. Install bolts
(2).
1/2
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. 2. Connect harness assembly (1).
End By:
a. Install the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump -
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Aug 21 22:10:37 UTC+0800 2020
2/2
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR GTF
Configuration: 323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02751808
Engine Oil Relief Valve - Remove and Install
SMCS - 1315-010
Removal Procedure
Start By:
a. Remove the electronic control module. Refer to Disassembly and Assembly, "Electronic
Control Module - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01377673
1/2
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. 1. Remove engine oil relief valve (1).
2. Remove gasket (2) (not shown). Discard gasket (2).
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01377673
1. Install a new gasket (2) (not shown).
2. Install engine oil relief valve (1). Tighten engine oil relief valve (1) to a torque of
49 ± 5 N·m (36 ± 4 lb ft).
End By:
a. Install the electronic control module. Refer to Disassembly and Assembly, "Electronic
Control Module - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Aug 21 22:11:36 UTC+0800 2020
2/2
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR GTF
Configuration: 323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02751881
Engine Oil Bypass Valve - Remove and Install
SMCS - 1306-010-BV
Removal Procedure
Start By:
a. Remove the oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01377713
1. Remove engine oil bypass valve (1). Remove gasket (2) (not shown). Discard gasket (2).
1/2
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...