This document provides instructions for removing and installing the bucket cylinder on a 322B L excavator. It describes disconnecting hydraulic lines, removing retaining pins and bolts, and using hoists to maneuver heavy components like the bucket linkage assembly. Precautions are outlined for containing fluid spills and avoiding burns from hot hydraulic oil. The process involves cleaning parts, applying grease, installing seals and bearings at specified depths, and torquing nuts to specified values.
Caterpillar cat 312 b l track type excavator (prefix 3fs) service repair manu...fjskkksmemm
This document provides instructions for removing and installing a flywheel on a Caterpillar 3064 engine. It describes:
1) Using various tools to remove the adapter, inner ring, and bolts securing the flywheel.
2) Lifting the flywheel off using a strap and lifting device, as it weighs 50 kg.
3) Instructions for removing the ring gear by heating and tapping it off.
4) The installation procedure lists cleaning and applying compounds before securing the flywheel back onto the crankshaft using bolts and checking the runout.
Caterpillar cat 966 f series ii wheel loader (prefix 8bg) service repair manu...fjsjfjskeksmem
This document provides instructions for disassembling and assembling the differential of a 966F Series II wheel loader. It describes:
1) Removing various components of the standard differential such as the case assembly, bevel gears, and spider and gear assembly.
2) Assembling the standard differential by installing corresponding components in reverse order.
3) Procedures for disassembling and assembling a limited slip differential, including removing discs, pinion gears, and housings, and installing components in reverse order. Measurements are taken to check end play during assembly.
Caterpillar cat 345 c excavator (prefix jar) service repair manual (jar00001 ...fjkskedmme
This document provides instructions for removing and installing the rear gear group on a 345C excavator. It details:
1) The required tools and parts for the job.
2) The step-by-step removal procedure which includes removing the electric starting motor, flywheel, rear gear components, seals, and bearings.
3) The installation procedure which provides directions for installing the rear gear group components in reverse order and ensuring proper bearing placement and torque specifications are followed.
Caterpillar cat 336 f l excavator (prefix kcs) service repair manual (kcs0000...fjkskedmme
This document provides instructions for removing and installing various components of a Caterpillar C9.3 engine, including the combustion head, ARD nozzle heater relay, ARD fuel solenoid valve, exhaust manifold, and exhaust elbow. The procedures describe disconnecting electrical connections and fluid lines, removing mounting hardware, and replacing gaskets and seals before reinstalling parts in the reverse order of removal. Safety precautions are provided regarding preventing contamination, allowing components to cool, and using approved lubricants.
Caterpillar cat 336 f l excavator (prefix nbs) service repair manual (nbs0000...fjsjekdmmeme
This document provides disassembly instructions for a 336F excavator travel motor. It lists 27 steps to fully disassemble the travel motor, including removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals, and more. Various tools are required to remove parts and release spring forces safely. Detailed illustrations accompany each step to show how to disassemble the individual components of the travel motor.
Caterpillar cat 336 f l xe excavator (prefix mtw) service repair manual (mtw0...fjkskedmme
This document provides disassembly instructions for a travel motor on a 336F LN XE excavator. It lists 27 steps to fully disassemble the travel motor, including removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals, and more. Detailed illustrations accompany each step to show how to remove each part in the proper sequence while maintaining their original positions and order for reassembly. Safety precautions are provided throughout to warn of potential spring forces or fluid containment.
The document provides instructions for removing and installing various fuel system components on a C18 Industrial Engine, including:
- Fuel priming pump removal and installation procedures in 3 steps.
- Fuel filter base removal procedure in 5 steps and disassembly procedure in 4 steps.
- Fuel filter base assembly procedure in 4 steps and installation procedure in 6 steps.
- Fuel transfer pump removal procedure in 6 steps and installation procedure in 7 steps.
- Electronic unit injector removal procedure involving 5 steps of disconnecting components and identifying parts.
Caterpillar cat 336 f l xe excavator (prefix ybh) service repair manual (ybh0...fjkskedmme
This document provides instructions for disassembling the travel motor on a 336F LNXE excavator. The 27 step procedure includes removing components like the motor head assembly, barrel assembly, piston assemblies, springs, seals, plates and more. Special tools are required and safety precautions must be followed when releasing spring forces. Detailed illustrations accompany each step to ensure correct reassembly.
Caterpillar cat 312 b l track type excavator (prefix 3fs) service repair manu...fjskkksmemm
This document provides instructions for removing and installing a flywheel on a Caterpillar 3064 engine. It describes:
1) Using various tools to remove the adapter, inner ring, and bolts securing the flywheel.
2) Lifting the flywheel off using a strap and lifting device, as it weighs 50 kg.
3) Instructions for removing the ring gear by heating and tapping it off.
4) The installation procedure lists cleaning and applying compounds before securing the flywheel back onto the crankshaft using bolts and checking the runout.
Caterpillar cat 966 f series ii wheel loader (prefix 8bg) service repair manu...fjsjfjskeksmem
This document provides instructions for disassembling and assembling the differential of a 966F Series II wheel loader. It describes:
1) Removing various components of the standard differential such as the case assembly, bevel gears, and spider and gear assembly.
2) Assembling the standard differential by installing corresponding components in reverse order.
3) Procedures for disassembling and assembling a limited slip differential, including removing discs, pinion gears, and housings, and installing components in reverse order. Measurements are taken to check end play during assembly.
Caterpillar cat 345 c excavator (prefix jar) service repair manual (jar00001 ...fjkskedmme
This document provides instructions for removing and installing the rear gear group on a 345C excavator. It details:
1) The required tools and parts for the job.
2) The step-by-step removal procedure which includes removing the electric starting motor, flywheel, rear gear components, seals, and bearings.
3) The installation procedure which provides directions for installing the rear gear group components in reverse order and ensuring proper bearing placement and torque specifications are followed.
Caterpillar cat 336 f l excavator (prefix kcs) service repair manual (kcs0000...fjkskedmme
This document provides instructions for removing and installing various components of a Caterpillar C9.3 engine, including the combustion head, ARD nozzle heater relay, ARD fuel solenoid valve, exhaust manifold, and exhaust elbow. The procedures describe disconnecting electrical connections and fluid lines, removing mounting hardware, and replacing gaskets and seals before reinstalling parts in the reverse order of removal. Safety precautions are provided regarding preventing contamination, allowing components to cool, and using approved lubricants.
Caterpillar cat 336 f l excavator (prefix nbs) service repair manual (nbs0000...fjsjekdmmeme
This document provides disassembly instructions for a 336F excavator travel motor. It lists 27 steps to fully disassemble the travel motor, including removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals, and more. Various tools are required to remove parts and release spring forces safely. Detailed illustrations accompany each step to show how to disassemble the individual components of the travel motor.
Caterpillar cat 336 f l xe excavator (prefix mtw) service repair manual (mtw0...fjkskedmme
This document provides disassembly instructions for a travel motor on a 336F LN XE excavator. It lists 27 steps to fully disassemble the travel motor, including removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals, and more. Detailed illustrations accompany each step to show how to remove each part in the proper sequence while maintaining their original positions and order for reassembly. Safety precautions are provided throughout to warn of potential spring forces or fluid containment.
The document provides instructions for removing and installing various fuel system components on a C18 Industrial Engine, including:
- Fuel priming pump removal and installation procedures in 3 steps.
- Fuel filter base removal procedure in 5 steps and disassembly procedure in 4 steps.
- Fuel filter base assembly procedure in 4 steps and installation procedure in 6 steps.
- Fuel transfer pump removal procedure in 6 steps and installation procedure in 7 steps.
- Electronic unit injector removal procedure involving 5 steps of disconnecting components and identifying parts.
Caterpillar cat 336 f l xe excavator (prefix ybh) service repair manual (ybh0...fjkskedmme
This document provides instructions for disassembling the travel motor on a 336F LNXE excavator. The 27 step procedure includes removing components like the motor head assembly, barrel assembly, piston assemblies, springs, seals, plates and more. Special tools are required and safety precautions must be followed when releasing spring forces. Detailed illustrations accompany each step to ensure correct reassembly.
Caterpillar Cat 322B L EXCAVATOR (Prefix 5CR) Service Repair Manual Instant D...ze6074xunong
This document provides instructions for removing and installing the bucket cylinder on a 322B L excavator. It describes 31 steps to disassemble and remove the bucket linkage group and components like pins, links, and seals. It then describes the process to clean, grease, and reinstall these components in the reverse order. Safety precautions are provided to contain fluids, release hydraulic pressure, and avoid personal injury when removing heavy parts.
Caterpillar Cat 322B L EXCAVATOR (Prefix 5CR) Service Repair Manual Instant D...f8uejkdkdmm3e
This document provides instructions for removing and installing the bucket linkage group and bucket cylinder on a Caterpillar 322B L excavator. The summary is as follows:
1. Release hydraulic pressure and disconnect hoses before removing components.
2. Remove retaining bolts and pins to separate the linkage group from the bucket and cylinder. Lift components out individually using hoists.
3. Clean pin bores and install new seals and bearings before reassembling with greased pins and bolts, ensuring proper clearance between moving parts.
Caterpillar Cat 322B L EXCAVATOR (Prefix 5CR) Service Repair Manual Instant D...gongfuao7509
This document provides instructions for removing and installing the bucket linkage group and bucket cylinder on a Caterpillar 322B L excavator. The procedures include removing pins and bolts to separate the various linkage and cylinder components, as well as instructions for installing replacement components and adjusting clearances using shims. Proper lubrication of pins, bolts and other components is emphasized during assembly.
Caterpillar Cat 322B L EXCAVATOR (Prefix 5CR) Service Repair Manual Instant D...yu5676962
This document provides instructions for removing and installing the bucket linkage group and bucket cylinder on a Caterpillar 322B L excavator. The procedures include removing pins and bolts to separate the various linkage and cylinder components, as well as instructions for installing replacement components and adjusting clearances using shims. Proper lubrication of pins, bolts and other components is emphasized during assembly.
Caterpillar Cat 322B L EXCAVATOR (Prefix 5CR) Service Repair Manual Instant D...f89siekkmdmm2w
This document provides instructions for removing and installing the bucket linkage group and bucket cylinder on a Caterpillar 322B L excavator. The summary is as follows:
1. Release hydraulic pressure and disconnect hoses before removing components.
2. Remove retaining bolts and pins to separate the linkage group from the bucket and cylinder. Lift components out individually using hoists.
3. Clean pin bores and install new seals and bearings before reassembling with greased pins and bolts, ensuring proper clearance between moving parts.
Caterpillar Cat 322B L EXCAVATOR (Prefix 5CR) Service Repair Manual (5CR00001...fhjsekdmdm3e
This document provides instructions for removing and installing the bucket cylinder on a 322B L excavator. It describes 31 steps to remove the bucket linkage group and 8 steps to remove the bucket cylinder. Safety precautions are provided, including releasing hydraulic pressure before disconnecting lines. Tools needed are also mentioned.
Caterpillar Cat 322B L EXCAVATOR (Prefix 5CR) Service Repair Manual Instant D...yin9niaojiao
This document provides instructions for removing and installing the bucket cylinder on a 322B L excavator. It describes 31 steps to disassemble and remove the bucket linkage group and bucket cylinder. It explains how to remove pins, links, seals, and bearings. It also provides instructions for installing these components in the reverse order, and describes lubricating and adjusting clearance between links. Safety precautions are provided to contain fluids and release hydraulic pressure before disconnecting lines.
Caterpillar Cat 322B L EXCAVATOR (Prefix 5CR) Service Repair Manual Instant D...shibi1322
This document provides instructions for removing and installing the bucket linkage group and bucket cylinder on a Caterpillar 322B L excavator. The procedures include removing pins and bolts to separate the various linkage and cylinder components, as well as instructions for installing replacement components and adjusting clearances using shims. Precautions are outlined for releasing hydraulic pressure before disconnecting lines.
Caterpillar Cat 322B L EXCAVATOR (Prefix 5CR) Service Repair Manual Instant D...8foskkdjdkdm3e
This document provides instructions for removing and installing the bucket cylinder on a 322B L excavator. It describes 31 steps to disassemble and remove the bucket linkage group and bucket cylinder. It explains how to remove pins, links, seals, and bearings. It also provides instructions for installing these components in the reverse order, and describes lubricating and adjusting clearance between links. Safety precautions are provided to contain fluids and release hydraulic pressure before disconnecting lines.
The document provides instructions for disassembling and assembling the track loader's power train components. It describes how to remove and install the sprocket assemblies, final drive cases, gears, idler pinions and bearings. The procedures involve draining fluids, removing guards and seals, and using various tools to loosen and tighten components while applying specified torques. Precise assembly requires cleaning parts and applying lubricants to ensure proper operation.
The document provides instructions for disassembling and assembling the track loader's power train components. It describes how to remove and install the sprocket assemblies, final drive cases, gears, idler pinions and bearings. The procedures involve draining fluids, removing guards and seals, and using various tools to loosen and tighten components while applying specified torques. Precise assembly requires cleaning parts and applying lubricants to ensure proper operation.
The document provides instructions for removing and installing sprocket assemblies on a track-type tractor. It involves 22 steps to remove the assemblies, which includes draining oil, removing seals, bearings, and other components. The 23 steps to install include pressing in new seals, bearings, and sprockets using specialized tools and applying precise forces, and adjusting bearings after reinstalling track roller frames. Proper cleaning, lubrication and torque specifications are noted throughout.
The document provides instructions for removing and installing sprocket assemblies on a track-type tractor. It involves 22 steps to remove the assemblies, which includes draining oil, removing seals, bearings, and other components. The 23 steps to install include pressing in new seals, bearings, and sprockets using specialized tools and applying precise forces, and adjusting bearings after reinstalling track roller frames. Proper cleaning, lubrication and torque specifications are noted throughout.
The document provides instructions for removing final drive cases, gears, idler pinions and bearings from a D7G track-type tractor. The steps include:
1) Removing bolts holding the final drive case in position.
2) Installing guide bolts and forcing screws to separate the final drive case from the steering clutch case.
3) Using wire to hold the idler pinion in place so the planet carrier does not fall when the final drive case is removed.
This document provides instructions for disassembling and assembling the swing drive of a 215B excavator. It begins by describing how to remove the swing drive by draining hydraulic fluid, attaching eyebolts and lifting it out. It then details how to disassemble the swing drive into individual parts like gears, bearings and seals. The assembly section provides step-by-step instructions for installing these parts in reverse order and includes details like heating bearings, applying lubricants and torquing bolts.
Caterpillar cat e120 b excavator (prefix 6jf) service repair manual (6jf00001...fjjskekfsem
This document provides instructions for disassembling and assembling the travel drives of an E120B excavator. It describes removing and disassembling the travel drive and travel motor components. It then describes cleaning and inspecting the parts and reassembling the travel drive, which involves determining shim thicknesses, installing seals and gears, and torquing bolts to the specified values. The overall process is described in 22 steps for disassembly and 46 steps for assembly.
Caterpillar cat e120 b excavator (prefix 6jf) service repair manual (6jf00001...ufjjsjekksemmd
This document provides instructions for disassembling and assembling the travel drives of an E120B excavator. It describes removing and disassembling the travel drive and travel motor components. It then describes cleaning and inspecting the parts and reassembling the travel drive, which involves determining shim thicknesses, installing seals and gears, and torquing bolts to the specified values. The overall process is described in 22 steps for disassembly and 46 steps for reassembly.
Caterpillar cat e120 b excavator (prefix 6jf) service repair manual (6jf00001...uufjdjdkkksmem
This document provides instructions for disassembling and assembling the travel drives of an E120B excavator. It describes removing and disassembling the travel drive and travel motor components. It then describes cleaning and inspecting the parts and reassembling the travel drive, which involves determining shim thicknesses, installing seals and gears, and torquing bolts to the specified values. The overall process is described in 22 steps for disassembly and 46 steps for reassembly.
Caterpillar cat e120 b excavator (prefix 6jf) service repair manual (6jf00001...fjkskekdmmenm
This document provides instructions for disassembling and assembling the travel drives of an E120B excavator. It describes removing and disassembling the travel drive and travel motor components. Steps are provided to disassemble the carrier assemblies, planetary gears, and other internal parts. The assembly instructions then describe reinstalling and reassembling the components in reverse order, including applying thread lock and installing seals and shims correctly.
Caterpillar cat e120 b excavator (prefix 6jf) service repair manual (6jf00001...fjsjefskekfmme
This document provides instructions for disassembling and assembling the travel drives of an E120B excavator. It describes removing and disassembling the travel drive and travel motor components. It then describes cleaning and inspecting the parts and reassembling the travel drive, which involves determining shim sizes, installing seals and gears, and torquing bolts to the specified values. The goal is to properly disassemble, clean, measure, and reassemble the travel drive components.
Toro reelmaster 5210 mower service repair manualfjsjekkdmme
This service manual provides information for technicians to troubleshoot, test, and repair major systems and components of the Reelmaster 5010 series mowers, including the 5210, 5410, 5510, and 5610 models. It covers safety instructions, product records and maintenance requirements, specifications and repairs for systems like the Kubota diesel engine, hydraulic system, electrical system, chassis, cutting units, and optional groomer. Technicians should refer to the operator's manuals for additional operating and maintenance instructions.
Toro groundsmaster 223 d mower service repair manualfjsjekkdmme
This service manual provides service technicians with maintenance, repair, and overhaul procedures for the TORO Groundsmaster 220-D/223-D mowers. It contains chapters covering the mower's safety instructions, product records, diesel engine, hydraulic system, electrical system, steering system, brakes, PTO, cutting units, and seasonal storage. The manual aims to give technicians a working guide for safely servicing the mower over its lifetime.
More Related Content
Similar to Caterpillar cat 322 b l excavator (prefix 5cr) service repair manual (5cr00001 and up)
Caterpillar Cat 322B L EXCAVATOR (Prefix 5CR) Service Repair Manual Instant D...ze6074xunong
This document provides instructions for removing and installing the bucket cylinder on a 322B L excavator. It describes 31 steps to disassemble and remove the bucket linkage group and components like pins, links, and seals. It then describes the process to clean, grease, and reinstall these components in the reverse order. Safety precautions are provided to contain fluids, release hydraulic pressure, and avoid personal injury when removing heavy parts.
Caterpillar Cat 322B L EXCAVATOR (Prefix 5CR) Service Repair Manual Instant D...f8uejkdkdmm3e
This document provides instructions for removing and installing the bucket linkage group and bucket cylinder on a Caterpillar 322B L excavator. The summary is as follows:
1. Release hydraulic pressure and disconnect hoses before removing components.
2. Remove retaining bolts and pins to separate the linkage group from the bucket and cylinder. Lift components out individually using hoists.
3. Clean pin bores and install new seals and bearings before reassembling with greased pins and bolts, ensuring proper clearance between moving parts.
Caterpillar Cat 322B L EXCAVATOR (Prefix 5CR) Service Repair Manual Instant D...gongfuao7509
This document provides instructions for removing and installing the bucket linkage group and bucket cylinder on a Caterpillar 322B L excavator. The procedures include removing pins and bolts to separate the various linkage and cylinder components, as well as instructions for installing replacement components and adjusting clearances using shims. Proper lubrication of pins, bolts and other components is emphasized during assembly.
Caterpillar Cat 322B L EXCAVATOR (Prefix 5CR) Service Repair Manual Instant D...yu5676962
This document provides instructions for removing and installing the bucket linkage group and bucket cylinder on a Caterpillar 322B L excavator. The procedures include removing pins and bolts to separate the various linkage and cylinder components, as well as instructions for installing replacement components and adjusting clearances using shims. Proper lubrication of pins, bolts and other components is emphasized during assembly.
Caterpillar Cat 322B L EXCAVATOR (Prefix 5CR) Service Repair Manual Instant D...f89siekkmdmm2w
This document provides instructions for removing and installing the bucket linkage group and bucket cylinder on a Caterpillar 322B L excavator. The summary is as follows:
1. Release hydraulic pressure and disconnect hoses before removing components.
2. Remove retaining bolts and pins to separate the linkage group from the bucket and cylinder. Lift components out individually using hoists.
3. Clean pin bores and install new seals and bearings before reassembling with greased pins and bolts, ensuring proper clearance between moving parts.
Caterpillar Cat 322B L EXCAVATOR (Prefix 5CR) Service Repair Manual (5CR00001...fhjsekdmdm3e
This document provides instructions for removing and installing the bucket cylinder on a 322B L excavator. It describes 31 steps to remove the bucket linkage group and 8 steps to remove the bucket cylinder. Safety precautions are provided, including releasing hydraulic pressure before disconnecting lines. Tools needed are also mentioned.
Caterpillar Cat 322B L EXCAVATOR (Prefix 5CR) Service Repair Manual Instant D...yin9niaojiao
This document provides instructions for removing and installing the bucket cylinder on a 322B L excavator. It describes 31 steps to disassemble and remove the bucket linkage group and bucket cylinder. It explains how to remove pins, links, seals, and bearings. It also provides instructions for installing these components in the reverse order, and describes lubricating and adjusting clearance between links. Safety precautions are provided to contain fluids and release hydraulic pressure before disconnecting lines.
Caterpillar Cat 322B L EXCAVATOR (Prefix 5CR) Service Repair Manual Instant D...shibi1322
This document provides instructions for removing and installing the bucket linkage group and bucket cylinder on a Caterpillar 322B L excavator. The procedures include removing pins and bolts to separate the various linkage and cylinder components, as well as instructions for installing replacement components and adjusting clearances using shims. Precautions are outlined for releasing hydraulic pressure before disconnecting lines.
Caterpillar Cat 322B L EXCAVATOR (Prefix 5CR) Service Repair Manual Instant D...8foskkdjdkdm3e
This document provides instructions for removing and installing the bucket cylinder on a 322B L excavator. It describes 31 steps to disassemble and remove the bucket linkage group and bucket cylinder. It explains how to remove pins, links, seals, and bearings. It also provides instructions for installing these components in the reverse order, and describes lubricating and adjusting clearance between links. Safety precautions are provided to contain fluids and release hydraulic pressure before disconnecting lines.
The document provides instructions for disassembling and assembling the track loader's power train components. It describes how to remove and install the sprocket assemblies, final drive cases, gears, idler pinions and bearings. The procedures involve draining fluids, removing guards and seals, and using various tools to loosen and tighten components while applying specified torques. Precise assembly requires cleaning parts and applying lubricants to ensure proper operation.
The document provides instructions for disassembling and assembling the track loader's power train components. It describes how to remove and install the sprocket assemblies, final drive cases, gears, idler pinions and bearings. The procedures involve draining fluids, removing guards and seals, and using various tools to loosen and tighten components while applying specified torques. Precise assembly requires cleaning parts and applying lubricants to ensure proper operation.
The document provides instructions for removing and installing sprocket assemblies on a track-type tractor. It involves 22 steps to remove the assemblies, which includes draining oil, removing seals, bearings, and other components. The 23 steps to install include pressing in new seals, bearings, and sprockets using specialized tools and applying precise forces, and adjusting bearings after reinstalling track roller frames. Proper cleaning, lubrication and torque specifications are noted throughout.
The document provides instructions for removing and installing sprocket assemblies on a track-type tractor. It involves 22 steps to remove the assemblies, which includes draining oil, removing seals, bearings, and other components. The 23 steps to install include pressing in new seals, bearings, and sprockets using specialized tools and applying precise forces, and adjusting bearings after reinstalling track roller frames. Proper cleaning, lubrication and torque specifications are noted throughout.
The document provides instructions for removing final drive cases, gears, idler pinions and bearings from a D7G track-type tractor. The steps include:
1) Removing bolts holding the final drive case in position.
2) Installing guide bolts and forcing screws to separate the final drive case from the steering clutch case.
3) Using wire to hold the idler pinion in place so the planet carrier does not fall when the final drive case is removed.
This document provides instructions for disassembling and assembling the swing drive of a 215B excavator. It begins by describing how to remove the swing drive by draining hydraulic fluid, attaching eyebolts and lifting it out. It then details how to disassemble the swing drive into individual parts like gears, bearings and seals. The assembly section provides step-by-step instructions for installing these parts in reverse order and includes details like heating bearings, applying lubricants and torquing bolts.
Caterpillar cat e120 b excavator (prefix 6jf) service repair manual (6jf00001...fjjskekfsem
This document provides instructions for disassembling and assembling the travel drives of an E120B excavator. It describes removing and disassembling the travel drive and travel motor components. It then describes cleaning and inspecting the parts and reassembling the travel drive, which involves determining shim thicknesses, installing seals and gears, and torquing bolts to the specified values. The overall process is described in 22 steps for disassembly and 46 steps for assembly.
Caterpillar cat e120 b excavator (prefix 6jf) service repair manual (6jf00001...ufjjsjekksemmd
This document provides instructions for disassembling and assembling the travel drives of an E120B excavator. It describes removing and disassembling the travel drive and travel motor components. It then describes cleaning and inspecting the parts and reassembling the travel drive, which involves determining shim thicknesses, installing seals and gears, and torquing bolts to the specified values. The overall process is described in 22 steps for disassembly and 46 steps for reassembly.
Caterpillar cat e120 b excavator (prefix 6jf) service repair manual (6jf00001...uufjdjdkkksmem
This document provides instructions for disassembling and assembling the travel drives of an E120B excavator. It describes removing and disassembling the travel drive and travel motor components. It then describes cleaning and inspecting the parts and reassembling the travel drive, which involves determining shim thicknesses, installing seals and gears, and torquing bolts to the specified values. The overall process is described in 22 steps for disassembly and 46 steps for reassembly.
Caterpillar cat e120 b excavator (prefix 6jf) service repair manual (6jf00001...fjkskekdmmenm
This document provides instructions for disassembling and assembling the travel drives of an E120B excavator. It describes removing and disassembling the travel drive and travel motor components. Steps are provided to disassemble the carrier assemblies, planetary gears, and other internal parts. The assembly instructions then describe reinstalling and reassembling the components in reverse order, including applying thread lock and installing seals and shims correctly.
Caterpillar cat e120 b excavator (prefix 6jf) service repair manual (6jf00001...fjsjefskekfmme
This document provides instructions for disassembling and assembling the travel drives of an E120B excavator. It describes removing and disassembling the travel drive and travel motor components. It then describes cleaning and inspecting the parts and reassembling the travel drive, which involves determining shim sizes, installing seals and gears, and torquing bolts to the specified values. The goal is to properly disassemble, clean, measure, and reassemble the travel drive components.
Similar to Caterpillar cat 322 b l excavator (prefix 5cr) service repair manual (5cr00001 and up) (20)
Toro reelmaster 5210 mower service repair manualfjsjekkdmme
This service manual provides information for technicians to troubleshoot, test, and repair major systems and components of the Reelmaster 5010 series mowers, including the 5210, 5410, 5510, and 5610 models. It covers safety instructions, product records and maintenance requirements, specifications and repairs for systems like the Kubota diesel engine, hydraulic system, electrical system, chassis, cutting units, and optional groomer. Technicians should refer to the operator's manuals for additional operating and maintenance instructions.
Toro groundsmaster 223 d mower service repair manualfjsjekkdmme
This service manual provides service technicians with maintenance, repair, and overhaul procedures for the TORO Groundsmaster 220-D/223-D mowers. It contains chapters covering the mower's safety instructions, product records, diesel engine, hydraulic system, electrical system, steering system, brakes, PTO, cutting units, and seasonal storage. The manual aims to give technicians a working guide for safely servicing the mower over its lifetime.
Toro greensmaster 3100 service repair manualfjsjekkdmme
This service manual provides information for technicians to troubleshoot, test, and repair major systems and components of the Greensmaster 3100 and 3050 golf course mowers. It contains chapters covering the engine, hydraulic system, electrical system, wheels/steering/brakes, various cutting unit types, and safety information. Technicians should follow the safety instructions when operating or performing maintenance on the mowers.
Stihl ts 700 cut off saw service repair manualfjsjekkdmme
The document provides specifications and repair procedures for STIHL TS 700 and TS 800 cut-off machines. It covers the power unit, fuel system, ignition system, clutch, carburetor, and other components. Troubleshooting charts are included to help locate faults. Detailed steps are listed for disassembly, repair, and reassembly of the various systems. Tightening torques and special tools required are also specified.
Stihl ms 341 chainsaw service repair manualfjsjekkdmme
The document provides specifications and troubleshooting information for STIHL chain saw models MS 341, MS 361, and MS 361 C. It covers the engine, fuel system, ignition system, chain lubrication system, clutch, chain drive, chain brake, rewind starter, carburetor heating, and other components. Troubleshooting charts provide potential causes and remedies for issues like the saw chain stopping under load, rotating at idle speed, or the rewind starter rope not rewinding properly. Tightening torques and repair instructions are also included.
Stihl 038 chainsaw service repair manualfjsjekkdmme
This service manual provides specifications, construction details, troubleshooting guides, and repair instructions for STIHL chain saw models 028 and 038. It covers the engine, ignition system, rewind starter, controls, lubrication system, and carburetor. The manual is intended for use by STIHL service technicians and dealers and provides the information needed to repair and maintain the saws.
Kohler courage sv720 service repair manualfjsjekkdmme
This service manual provides information for servicing Kohler SV710-SV840 series engines. It contains sections on safety, maintenance, specifications, tools, troubleshooting, and disassembly/reassembly instructions. The maintenance section outlines routine maintenance tasks such as oil and filter changes and component inspections. The specifications section lists physical dimensions, torque specifications, and other technical details. Disassembly and reassembly instructions provide step-by-step guides for servicing engine components.
Kohler courage sv600 vertical crankshaft engine service repair manualfjsjekkdmme
This document provides operation and maintenance instructions for Kohler SV470-SV620 engines. It includes sections on safety, maintenance, specifications, tools and aids, troubleshooting, and disassembly/reassembly. The maintenance schedule lists tasks such as changing the oil, inspecting components, and adjusting valves. Specification tables provide engine dimensions and torque specifications for fasteners. Warnings advise of dangers such as accidental starts, hot parts, and explosive fuel.
Kohler command pro cv940 vertical crankshaft service repair manualfjsjekkdmme
This service manual provides information for servicing a vertical crankshaft Command Pro engine models CV940-CV1000. The manual contains 10 sections covering safety, tools, troubleshooting, air/fuel systems, electrical systems, disassembly, inspection, reassembly, and lubrication. Section 1 outlines important safety precautions to follow when servicing the engine, including warnings about rotating parts, hot parts, hazardous chemicals, explosive and toxic fumes. It also explains how to identify the engine using model, serial and specification numbers.
Kohler command cv740 vertical crankshaft engine service repair manualfjsjekkdmme
This document is a service manual for the vertical crankshaft COMMAND CV17-745 engine. It contains 11 sections covering safety, troubleshooting, maintenance, disassembly, inspection, and reassembly of the engine. The manual provides specifications for the engine including power output, torque, bore size, stroke, and displacement for each model. It also includes diagrams showing typical engine dimensions and explanations of identification numbers. Safety precautions are outlined regarding rotating parts, hot parts, accidental starts, harmful exhaust, and use of proper fuels and oils.
Kohler command ch740 service repair manualfjsjekkdmme
This document provides service information for Kohler CH18-CH25, CH620-CH730, CH740, CH750 engines including:
1. Safety precautions and instructions that must be followed before operating or servicing the engine.
2. A maintenance schedule and instructions for performing routine maintenance like oil changes, filter replacement, etc.
3. Specifications for the engine including dimensions, torque specifications, oil recommendations, and other technical details.
Kawasaki kbl23 a trimmer brushcutter service repair manualfjsjekkdmme
This document provides information for servicing trimmer/brushcutter engines produced by Kawasaki Heavy Industries, including:
- An overview of the manual's purpose and scope, how to use it safely, and basic service procedures.
- Specifications, maintenance schedules, torque values, and clearance and setting tables to guide repairs.
- Emission control system requirements and a list of abbreviations used.
Kawasaki fr651 v 4 stroke air-cooled v-twin gasoline engine service repair ma...fjsjekkdmme
This document provides instructions for using a service manual to locate repair information for 4-stroke air-cooled V-twin gasoline engines. It includes a quick reference guide and table of contents to navigate the manual. Proper service requires following procedures carefully, using correct tools, and heeding safety warnings.
Kawasaki fh770 d kai 4 stroke air-cooled v-twin gasoline engine service repai...fjsjekkdmme
This document provides a service manual for an FH770D KAI 4-stroke air-cooled v-twin gasoline engine. It includes sections on general information, periodic maintenance, fuel system, cooling system, engine top end, lubrication system, camshaft/crankshaft, electrical system, troubleshooting, and emissions control information. The manual provides guidance on safely servicing the engine including instructions on cleaning, torque specifications, replacement parts, and inspection criteria. It also includes an exploded view diagram, specifications, and model identification information.
Jcb diesel 1000 series engine model aj service repair manualfjsjekkdmme
This document is a workshop manual for Perkins New 1000 Series diesel engines used in industrial and agricultural applications. It provides detailed instructions for maintenance, repair, and overhaul of engine components. The manual contains 25 chapters covering general information, specifications, and repair/overhaul procedures for all major engine systems.
New holland speedrower 200 tier 3 self propelled windrower service repair man...fjsjekkdmme
This document is a service manual for the Speedrower 200 and Speedrower 240 self-propelled windrowers. It contains safety information and sections covering the engine, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, steering, cab climate control, electrical systems, and the platform, cab, bodywork and decals. Safety is the top priority, with warnings regarding slopes, overhead hazards, high pressure fluids, moving parts, and keeping unauthorized persons away from machinery.
New holland h9880 bale wagon service repair manualfjsjekkdmme
This document is a service manual for New Holland H9870/H9880 Bale Wagons that contains:
1) A table of contents listing the various systems of the bale wagons that are described in sections in the manual, such as the engine, transmission, hydraulics, electrical systems, and more.
2) An introduction section about the manual and important safety information for working on the equipment.
3) Sections providing service and repair instructions for the various mechanical, electrical, and hydraulic systems of the bale wagons.
New holland 4835 tractor service repair manualfjsjekkdmme
This document is the contents page for a repair manual for a 35 Series Tractor for models 4835, 5635, 6635, 7635. The repair manual contains 11 sections covering general information, the engine, electrical system, high pressure hydraulic system, low pressure hydraulic system, power train, front axle, PTO, cab, air conditioning, and special tools. The user is instructed to cut out the label and insert it into the binder spine. They are then provided a link to obtain the complete repair manual.
Massey ferguson mf 690 tractor ( 1984 ( fr )) service parts catalogue manual...fjsjekkdmme
This document provides part numbers and descriptions for components of a Massey Ferguson 690 tractor engine from 1984. It includes sections on the fan, cylinder block, crankshaft, pistons, connecting rods, flywheel, starter ring, front end drive input/output, cylinder head, water outlet/inlet, and other systems. Each section lists the relevant part numbers, quantities, descriptions, and any comments for repair or replacement parts.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 322B L EXCAVATOR 5CR
Configuration: 322B EXCAVATOR WITH FIELD INSTALLED COMBINE/ROTATE FUNCTIONS 5CR00001-UP (MACHINE)
Disassembly and Assembly
322B & 322B L EXCAVATORS MACHINE SYSTEMS
Media Number -SENR1647-00 Publication Date -07/01/1997 Date Updated -30/03/2004
SENR16470004
Bucket Linkage Group
SMCS - 6513-010
Remove & Install Bucket Linkage Group
1/8322B EXCAVATOR WITH FIELD INSTALLED COMBINE/ROTATE FUNCTION...
2019/10/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. 1. Start the machine, and position the bucket, stick and rod links as shown.
2. Remove retaining bolt (1) and two nuts (2) from bucket pin (3).
When bucket pin (3) is removed, link assembly (4) will swing forward
and out of the bucket. To prevent possible personal injury, do not stand
in front of link assembly (4) when bucket pin (3) is being removed.
3. Using a hammer and punch, remove bucket pin (3) far enough to free link assembly (4) from
the bucket. Do not remove bucket pin (3) completely from the bucket. Link assembly (4) will
swing forward when the bucket pin is removed.
4. Using two persons, remove bucket pin (3) by hand. The weight of the bucket pin is 23 kg (50
lb). Remove O-ring seals (5) from the flanges on the bucket.
2/8322B EXCAVATOR WITH FIELD INSTALLED COMBINE/ROTATE FUNCTION...
2019/10/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 5. Fasten a hoist to link assembly (4) as shown, and raise it until it is in a horizontal position.
6. Remove two nuts (6) and retaining bolt (7) from pin (8). Remove pin (8) from the link
assemblies and the rod end of the bucket cylinder. Remove link assembly (4). The weight of pin
(8) is 23 kg (50 lb). The weight of link assembly (4) is 102 kg (225 lb).
7. Fasten a hoist to left hand link assembly (9) as shown. Remove two nuts (10) and retaining bolt
(11) from pin (12). Using a hammer and punch, drive pin (12) into the stick until the left hand link
assembly is free. Remove the left hand link assembly. The weight of the left hand link assembly is
25 kg (55 lb). Refasten the hoist to the right hand link assembly. Remove pin (12) from the stick
and right hand link assembly. Remove the right hand link assembly. The weight of the right hand
link assembly is 20 kg (45 lb). The weight of pin (12) is 14 kg (30 lb).
8. Remove six lip seals (13) from link assembly (4).
3/8322B EXCAVATOR WITH FIELD INSTALLED COMBINE/ROTATE FUNCTION...
2019/10/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 9. Remove two bearings (14) from the open end of the link assembly with Tooling (B). Fasten
Tooling (B) to the link assembly as shown. Fasten a hoist to Tooling (B) to support it; then
remove the bearing. Remove the bearing on the other side of the link assembly the same way.
10. Remove the two bearings from the closed end of the link assembly with a chisel or by cutting.
11. Remove two lip seals (15) from the stick at the stick-to-bucket linkage pin joint.
12. Remove the two bearings from the stick at the stick-to-bucket linkage pin joint with Tooling
(C). Fasten Tooling (C) to the bearing as shown. Fasten a hoist to Tooling (C) to support it; then
remove the bearing. Remove the bearing on the other side of the stick the same way.
13. Remove round shim (16) from the inside of the right hand link assembly.
4/8322B EXCAVATOR WITH FIELD INSTALLED COMBINE/ROTATE FUNCTION...
2019/10/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 14. Remove bolt (17) and the washer that hold U-shaped shim (18) to the inside of the right hand
link assembly.
NOTE: The following steps are for the installation of the bucket linkage group.
NOTICE
Make sure the stick pin bore, link assembly bores, pins and O-ring
seals are thoroughly clean and free of dirt prior to installation of the
bucket linkage group.
15. Install the two bearings in the stick at the stick-to-bucket linkage pin joint. Lower the
temperature of the bearings, and install them in the pin bore until each one is 7.5 ± 0.8 mm (.30
± .03 in) below the outside surface of the stick.
16. Install the two bearings in the closed end of link assembly (4). Lower the temperature of the
bearings, and install them in the pin bore until each one is 7.0 ± 0.8 mm (.28 ± .03 in) below the
outside surface of the link assembly.
17. Install two bearings (14) in the open end of link assembly (4). Lower the temperature of the
bearings, and install them in the pin bores until each one is 7.0 ± 0.8 mm (.28 ± .03 in) below the
outside surface of the link assembly.
NOTICE
To prevent dirt and debris from entering the pin bores in link assembly
(4) and the stick, install all lip seals (13) and (15) with the sealing lip
facing toward the outside of the pin bores.
18. Using Tool (A), install the six lip seals (13) in link assembly (4). Install the seals with the
sealing lip facing toward the outside of the pin bores and until each one makes contact with the
bearing.
19. Using Tool (A), install the two lip seals (15) in the stick. Install the seals with the sealing lip
facing toward the outside of the pin bore and until each one makes contact with a bearing.
5/8322B EXCAVATOR WITH FIELD INSTALLED COMBINE/ROTATE FUNCTION...
2019/10/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 20. Apply 5P-0960 Multipurpose Grease on the bearings and seals in the stick and link
assembly.
21. Apply 5P-0960 Multipurpose Grease on pin (12). Install the right hand link assembly, left
hand link assembly (9) and pin (12) as shown. Align the retaining bolt hole in pin (12) with the
retaining bolt hole in left hand link assembly (9). Temporarily install retaining bolt (11) and two
nuts (10) which hold it.
22. Prior to installing link assembly (4), make sure the grease fitting in the rod end of the bucket
cylinder is facing away from the stick.
23. Fasten a hoist to link assembly (4), and put it in position on the rod end of the bucket cylinder
and between the right and left hand link assemblies. Apply 5P-0960 Multipurpose Grease on pin
(8). Install the pin to hold the unit together. Align the retaining bolt hole in pin (8) with the
retaining bolt hole in the left hand link assembly. Temporarily install retaining bolt (7) and two
nuts (6) which hold it.
24. Slide link assembly (4) to one side until it makes contact with left hand link assembly (9).
Measure the total clearance between link assembly (4) and the right hand link assembly. The total
clearance must not be more than 0.8 mm (.03 in). If the clearance is greater than 0.8 mm (.03 in),
shim will be required.
6/8322B EXCAVATOR WITH FIELD INSTALLED COMBINE/ROTATE FUNCTION...
2019/10/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. 25. If it has been determined that shims need to be added, remove the right hand link assembly.
Install a U-shaped shim (18), the washer and bolt (17).
26. Apply 5P-0960 Multipurpose Grease on shims (16) to hold them th the inside of the right
hand link assembly. Reinstall the right hand link assembly.
27. Temporarily install an O-ring seal (5) on each flange of the link at the bucket-to-link assembly
pin bore.
28. Make sure the threaded puller hole in bucket pin (3) is clean. Apply 5P-0960 Multipurpose
Grease on bucket pin (3). Push the link assembly in position in the bucket. Install bucket pin (3)
with a hammer. Put the retaining bolt hole in bucket pin (3) in alignment with the retaining bolt
hole in the bucket. Temporarily install retaining bolt (1) and two nuts (2).
7/8322B EXCAVATOR WITH FIELD INSTALLED COMBINE/ROTATE FUNCTION...
2019/10/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 29. Rotate pins (8) and (12) until the retaining bolt hole in each pin is in horizontal alignment as
shown in the illustration.
30. Tighten retaining nuts (2), (6) and (10) as shown in the illustration. Tighten the outside nut
until it is even or 0.5 mm (0.02 in) above the end of the retaining bolt. Tighten the inside nut
against the outside nut to a torque of 200 ± 40 N·m (150 ± 30 lb ft).
31. Lubricate the bucket pins. Refer to the Operation & Maintenance Manual for the correct
procedure.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 27 12:19:53 UTC+0800 2019
8/8322B EXCAVATOR WITH FIELD INSTALLED COMBINE/ROTATE FUNCTION...
2019/10/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 322B L EXCAVATOR 5CR
Configuration: 322B EXCAVATOR WITH FIELD INSTALLED COMBINE/ROTATE FUNCTIONS 5CR00001-UP (MACHINE)
Disassembly and Assembly
322B & 322B L EXCAVATORS MACHINE SYSTEMS
Media Number -SENR1647-00 Publication Date -07/01/1997 Date Updated -30/03/2004
SENR16470005
Bucket Cylinder
SMCS - 5457-010; 5457-017
Remove & Install Bucket Cylinder
Fluid Spillage Containment
Care must be taken to ensure that fluids are contained during performance of inspection,
maintenance, testing, adjusting and repair of the machine. Be prepared to collect the fluid with
suitable containers before opening any compartment or disassembling any component containing
fluids. Refer to "Tools And Shop Products Guide", NENG2500 for tools and supplies suitable to
collect and contain fluids in Caterpillar machines. Dispose fluids according to local regulations and
mandates.
At operating temperature, the hydraulic oil is hot and under pressure.
Hot oil can cause burns. To prevent possible personal injury, release the
pressure in the implement hydraulic circuits (boom, stick and bucket)
before any hydraulic lines or components are disconnected and
removed.
1. Release the pressure in the implement hydraulic circuits (boom, stick, and bucket) before any
hydraulic lines or components are disconnected or removed as follows:
a. Start the engine. Fully extend the stick and bucket. Lower the stick and bucket to the ground.
b. Shut off the engine, and place key in the "ON" position. Put the hydraulic activation control lever
in the "UNLOCK" position.
c. Move the control levers for boom, stick and swing to all full stroke positions. This will release
any pressure that might be present in the pilot system.
1/8322B EXCAVATOR WITH FIELD INSTALLED COMBINE/ROTATE FUNCTION...
2019/10/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. d. Return the key to "OFF" position.
e. Slowly loosen the fill plug on the hydraulic tank, and release the pressure.
f. Tighten the fill plug on the hydraulic tank to as torque of 68 ± 7 N·m (50 ± 5 lb ft).
g. The pressure in the hydraulic system has been released and lines and components can be removed.
2. Fasten a hoist to the rod end of the bucket cylinder as shown. Put a wood block (3) under the link
assemblies as a support.
3. Remove the two nuts and retaining bolt (1). Remove pin (2). The weight of the pin is 23 kg (50
lb).
4. Raise bucket cylinder (4) until it is level; then fasten a lifting sling and a hoist to the head end of
the bucket cylinder as shown. A small amount of oil will drain from hoses (5) when they are
disconnected. Disconnect two hoses (5) from the bucket cylinder. Put plugs in the ends of the hoses
to prevent oil loss and to keep contaminants out of the hydraulic system.
5. Remove pin assembly retaining bolt (6), the washer, pin assembly (7) and the spacer. Remove the
bucket cylinder. The weight of the bucket cylinder is 193 kg (425 lb).
NOTE: Machines may be equipped with shims between the stick and bucket cylinder at the stick-to-
bucket cylinder pin joint. For assembly purposes, put identification marks on the shims as to their
location.
6. Remove the shims (if so equipped) at the stick-to-bucket cylinder pin joint.
2/8322B EXCAVATOR WITH FIELD INSTALLED COMBINE/ROTATE FUNCTION...
2019/10/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. NOTE: The following steps are for the installation of the bucket cylinder.
7. Make sure the pin bores in the stick, link assemblies, and bucket cylinder are clean and free of dirt
prior to installation of the bucket cylinder.
8. Fasten a hoist to bucket cylinder (4), and put it in position in the stick. Make sure the pin bores in
the stick and bucket cylinder are in alignment. Also, make sure the grease fitting in the head end and
rod end of the bucket cylinder are facing away from the stick.
9. Apply 5P-0960 Multipurpose Grease on pin assembly (7). Temporarily install the pin assembly.
Do not remove the hoist from the bucket cylinder at this time.
Top View Of Stick And Bucket Cylinder
10. Slide the bucket cylinder to one side until it makes contact with the stick. Measure the total
clearance between the bucket cylinder and stick at the pin bore. The total clearance of (a) and (b)
must not be more than 1.0 mm (.04 in). If the total clearance is less than 1.0 mm (.04 in), the
addition of shims between the bucket cylinder and stick will not be required. If the total clearance is
more than 1.0 mm (.04 in), add the correct thickness of shims to obtain the necessary clearance.
11. If it has been determined that shims need to be installed between the stick and bucket cylinder,
remove pin assembly (7). Install the shims between the stick and bucket cylinder on the side
opposite the pin assembly retaining bolt; then reinstall the spacer and pin assembly (7). Install pin
assembly retaining bolt (6) and the washer that holds the pin assembly in position. Tighten pin
assembly retaining bolt (6) to a torque of 325 ± 40 N·m (240 ± 30 lb ft).
3/8322B EXCAVATOR WITH FIELD INSTALLED COMBINE/ROTATE FUNCTION...
2019/10/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. 12. Lower the bucket cylinder between the link assemblies. Apply 5P-0960 Multipurpose Grease
on pin (2). Make sure the bore in the bucket cylinder rod is in alignment with the bores in the link
assemblies. Install pin (2). Install retaining bolt (1) and the two nuts.
13. Rotate pin (2) until it is in the position shown. Tighten the nuts on retaining bolt (1) as shown in
the illustration. Tighten the outside nut until it is even or 0.5 mm (.02 in) above the end of the
retaining bolt. Tighten the inside nut against the outside nut to a torque of 200 ± 40 N·m (150 ± 30
lb ft).
14. Check the condition of the O-ring seals in the ends of hoses (5) prior to installation. If the seals
are damaged, use new parts for replacement. Connect the two hoses to the bucket cylinder.
15. Fill the hydraulic oil tank with oil to the correct level. Lubricate the bucket cylinder support pins.
Refer to the Operation & Maintenance Manual for the correct procedures.
16. Start the machine, and run it at low idle speed. Move the control lever for the bucket cylinder so
the cylinder rod extends to its halfway position; then retract the cylinder rod. The cylinder should be
cycled this way approximately ten times to remove the air from the hydraulic system. Recheck the
oil level in the hydraulic oil tank.
Disassemble & Assemble Bucket Cylinder
4/8322B EXCAVATOR WITH FIELD INSTALLED COMBINE/ROTATE FUNCTION...
2019/10/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Start By:
a. remove bucket cylinder
NOTE: Several different bucket cylinder groups are available. The disassembly and assembly
procedure which follows is similar for all the bucket cylinder groups. However, reference must be
made to the 322B & 322B L Excavator Attachments Specifications module, SENR1637, for the
correct specifications for a specific bucket cylinder group.
Fluid Spillage Containment
Care must be taken to ensure that fluids are contained during performance of inspection,
maintenance, testing, adjusting and repair of the machine. Be prepared to collect the fluid with
suitable containers before opening any compartment or disassembling any component containing
fluids. Refer to "Tools And Shop Products Guide", NENG2500 for tools and supplies suitable to
collect and contain fluids in Caterpillar machines. Dispose fluids according to local regulations and
mandates.
5/8322B EXCAVATOR WITH FIELD INSTALLED COMBINE/ROTATE FUNCTION...
2019/10/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 1. Put the bucket cylinder on Tooling (A). The weight of the bucket cylinder is 193 kg (425 lb).
2. Remove grease fittings (10) from the cylinder assembly and the rod assembly.
3. Remove 12 bolts (6) that hold head (23) to cylinder assembly (22).
4. Use Tooling (A), to slide rod assembly (24) out of cylinder assembly (22).
5. Remove seal assembly (20), two rings (19), two rings (18) and two rings (17) from the piston.
6. Remove setscrew (13) and ball (14) from locknut (15). Using Tool (B), remove locknut (15) that
holds piston (21) to rod assembly (24). Remove shim (16). Remove the piston from the rod
assembly.
7. Slide cylinder assembly (22) back onto the rod assembly. Install bolts (6) that hold head (23) to
the cylinder assembly. Pull the cylinder assembly and head (23) as a unit away from the rod
assembly. Remove the head from the cylinder assembly.
8. Remove ring (8), O-ring seal (9), ring (7), bearing (5), seal (1), ring (2), seal (3) and seal (4) from
head (23).
9. Remove lip seal (11) from both sides of the pin bore in the cylinder assembly. Remove lip seal
(25) from both sides of the pin bore in the rod assembly.
10. Remove bearing (12) from the pin bore in the cylinder assembly. Remove bearing (26) from the
pin bore in the rod assembly.
NOTE: The following steps are for the assembly of the bucket cylinder. Refer to Illustration
D86074 for assembly of the bucket cylinder.
11. Check the condition of all parts of the bucket cylinder for wear or damage. If any of the parts are
worn or damaged, use new parts for replacement.
6/8322B EXCAVATOR WITH FIELD INSTALLED COMBINE/ROTATE FUNCTION...
2019/10/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. 12. Install seal (4), seal (3) and ring (2) in head (23) as shown. Install lip seal (1) in head (23) with
the lip of the seal facing away from the inside of the cylinder. Install bearing (5) and ring (7) in head
(23) as shown. Install O-ring seal (9) and ring (8) in head (23) as shown.
13. Put clean hydraulic oil on the lip of seal (1), ring (2), seal (3) and seal (4).
14. Put head (23) in position on cylinder assembly (22). Install 12 bolts (6) that hold it. Install rod
assembly (24) in head (23) and the cylinder assembly. Remove 12 bolts (6). Remove cylinder
assembly (22) from the rod assembly and head.
NOTE: Step 16 is only for cylinders equipped with a
119-5304 Locknut. Steps 17 and 18 are only for cylinders equipped with a 7Y-4695 Locknut and a
7I-1018 Locknut.
15. Install piston (21) on the rod assembly. Lubricate the threads on the end of the rod assembly with
4C-5593 Thread Compound. Install spacer (16). Install locknut (15). Tighten locknut (15), with
Tool (B), to the specified torque value.
16. Install piston (21) on the rod assembly. Lubricate the threads on the end of the rod assembly with
4C-5593 Thread Compound. Install spacer (16). Install locknut (15). Tighten locknut (15), with
Tool (B), to the specified torque value. Install ball (14) and setscrew (13) in the locknut. Tighten the
setscrew to the specified torque value.
17. Clean the remaining threads in the setscrew hole of the locknut. Make sure the remaining threads
are clean and dry. To prevent setscrew (13) from loosening, apply 5P-3321 Fast Cure Epoxy in the
threaded setscrew hole. Make sure the epoxy is even with the outside surface of the locknut after
application.
18. Install two rings (17), two rings (18), two rings (19) and seal assembly (20) on piston (21).
Lubricate the outside of the piston with 1P-0808 General Purpose Lubricant.
19. Using Tooling (A), Install cylinder assembly (22) on the rod assembly. Install 12 bolts (6) that
hold head (23) to the cylinder assembly. Tighten bolts (6) with the rod assembly fully extended.
Tighten the bolts to the specified torque value.
20. Lower the temperature of bearing (26). Using Tool (C), install the bearing the pin bore of the rod
assembly. Install the bearing until it is centered in the bore. Using Tool (C), install two lip seals (25)
in the pin bore of the rod assembly. Install the seals with the sealing lips facing out and until they
make contact with the bearing.
21. Lower the temperature of bearing (12). Using Tool (C), install the bearing the pin bore of the
cylinder assembly. Install the bearing until it is centered in the bore. Using Tool (C), install two lip
seals (11) in the pin bore of the cylinder assembly. Install the seals with the sealing lips facing out
and until they make contact with the bearing.
22. Install grease fitting (10) in the cylinder assembly. Install grease fitting (10) in the rod assembly.
Tighten the grease fittings to the specified torque value.
End By:
a. install bucket cylinder
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Sun Oct 27 12:20:49 UTC+0800 2019
7/8322B EXCAVATOR WITH FIELD INSTALLED COMBINE/ROTATE FUNCTION...
2019/10/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 322B L EXCAVATOR 5CR
Configuration: 322B EXCAVATOR WITH FIELD INSTALLED COMBINE/ROTATE FUNCTIONS 5CR00001-UP (MACHINE)
Disassembly and Assembly
322B & 322B L EXCAVATORS MACHINE SYSTEMS
Media Number -SENR1647-00 Publication Date -07/01/1997 Date Updated -30/03/2004
SENR16470006
Stick Cylinder
SMCS - 5458-010; 5458-017
Remove & Install Stick Cylinder
Fluid Spillage Containment
Care must be taken to ensure that fluids are contained during performance of inspection,
maintenance, testing, adjusting and repair of the machine. Be prepared to collect the fluid with
suitable containers before opening any compartment or disassembling any component containing
fluids. Refer to "Tools And Shop Products Guide", NENG2500 for tools and supplies suitable to
collect and contain fluids in Caterpillar machines. Dispose fluids according to local regulations and
mandates.
At operating temperature, the hydraulic oil is hot and under pressure.
Hot oil can cause burns. To prevent possible personal injury, release the
pressure in the implement hydraulic circuits (boom, stick and bucket)
before any hydraulic lines or components are disconnected and
removed.
1. Release the pressure in the implement hydraulic circuits (boom, stick, and bucket) before any
hydraulic lines or components are disconnected or removed as follows:
a. Start the engine. Fully extend the stick and bucket. Lower the stick and bucket to the ground.
b. Shut off the engine, and place key in the "ON" position. Put the hydraulic activation control lever
in the "UNLOCK" position.
c. Move the control levers for boom, stick and swing to all full stroke positions. This will release
any pressure that might be present in the pilot system.
1/6322B EXCAVATOR WITH FIELD INSTALLED COMBINE/ROTATE FUNCTION...
2019/10/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. d. Return the key to "OFF" position.
e. Slowly loosen the fill plug on the hydraulic tank, and release the pressure.
f. Tighten the fill plug on the hydraulic tank to as torque of 68 ± 7 N·m (50 ± 5 lb ft).
g. The pressure in the hydraulic system has been released and lines and components can be removed.
2. Fasten a hoist to stick cylinder (3) as shown.
3. A small amount of oil will drain from tube assemblies (4) when they are disconnected. Disconnect
two tube assemblies (4) at the head end of the stick cylinder. Put plugs in the ends of the tube
assemblies to prevent oil loss and to keep contaminants out of the hydraulic system. Disconnect
lubrication line (7) for the mounting pin assembly at the head end of the stick cylinder.
4. Remove pin assembly retaining bolt (1), the washer, pin assembly (2) and the spacer. Remove pin
assembly retaining bolt (6), the washer, pin assembly (5) and the spacer. Remove stick cylinder (3).
The weight of the stick cylinder is 297 kg (655 lb).
NOTE: Machines may be equipped with shims between the stick cylinder and boom at the stick
cylinder-to-boom pin joint and at the stick cylinder and stick at the stick cylinder-to-stick pin joint.
For assembly purposes, put identification marks on the shims as to their location.
5. Remove the shims (if so equipped) at the stick cylinder-to-boom pin joint and the stick cylinder-to
-stick pin joint.
NOTE: The following steps are for installation of the stick cylinder.
6. Make sure the pin bores in the stick cylinder, boom and stick are clean and free of dirt prior to
installation of the stick cylinder.
7. Fasten a hoist to stick cylinder (3), and put in position on the boom and stick. Make sure the pin
bores in the stick cylinder are in alignment with the pin bores in the stick and boom.
8. Apply 5P-0960 Multipurpose Grease on pin assemblies (2) and (5). Temporarily install the two
pin assemblies. Do not remove the hoist from the stick cylinder at this time.
2/6322B EXCAVATOR WITH FIELD INSTALLED COMBINE/ROTATE FUNCTION...
2019/10/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Typical Example
9. Slide the stick cylinder to one side until it makes contact with the boom and the stick. Measure the
total clearance between the stick cylinder and the boom and the stick cylinder and stick at each pin
bore. The total clearance of (a) and (b) must not be more than 1.0 mm (.04 in) at each pin bore. If
the total clearance is less than 1.0 mm (.04 in), the addition of shims between the stick cylinder and
boom or the stick cylinder and stick will not be required. If the total clearance is more than 1.0 mm
(.04 in), add the correct thickness of shims to obtain the necessary clearance.
10. If it has been determined that shims need to be installed between the stick cylinder and boom
and the stick cylinder and stick, remove pin assemblies (2) and (5). Install the shims between the
stick cylinder and boom and the stick cylinder and stick on the side opposite the pin assembly
retaining bolts; then reinstall the spacers and pin assemblies (2) and (5). Install pin assembly
retaining bolts (1) and (6) that hold the pin assemblies in position. Tighten bolts (1) and (6) to a
torque of 325 ± 40 N·m (240 ± 30 lb ft).
11. Check the condition of the O-ring seals in tube assemblies (4). If the seals are damaged, use new
parts for replacement. Connect tube assemblies (4) to the stick cylinder. Connect lubrication line (7)
to the stick cylinder.
12. Fill the hydraulic oil tank with oil to the correct level. Lubricate the support pins for the stick
cylinder. Refer to the Operation & Maintenance Manual for the correct procedure.
13. Start the machine, and run it at low idle speed. Move the control lever for the stick cylinder so
the cylinder rod extends to its halfway position; then retract the cylinder rod. The cylinder should be
cycled this way approximately ten times to remove the air from the hydraulic system. Recheck the
oil level in the hydraulic oil tank.
Disassemble & Assemble Stick Cylinder
3/6322B EXCAVATOR WITH FIELD INSTALLED COMBINE/ROTATE FUNCTION...
2019/10/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Start By:
a. remove stick cylinder
NOTE: Several different stick cylinder groups are available. The disassembly and assembly
procedure which follows is similar for the stick cylinder groups. However, reference must be made
to the 322B & 322B L Excavator Attachments Specifications module, SENR1637, for the correct
specifications for a specific stick cylinder group.
Fluid Spillage Containment
Care must be taken to ensure that fluids are contained during performance of inspection,
maintenance, testing, adjusting and repair of the machine. Be prepared to collect the fluid with
suitable containers before opening any compartment or disassembling any component containing
fluids. Refer to "Tools And Shop Products Guide", NENG2500 for tools and supplies suitable to
collect and contain fluids in Caterpillar machines. Dispose fluids according to local regulations and
mandates.
4/6322B EXCAVATOR WITH FIELD INSTALLED COMBINE/ROTATE FUNCTION...
2019/10/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...