This document provides instructions for removing and installing the valve mechanism cover base on a 320D LRR excavator with a C6.4 engine. The removal procedure involves removing clips and disconnecting harnesses from the electronic unit injectors, then removing bolts to detach the cover base. The installation procedure specifies tightening bolts and reconnecting harnesses in the reverse order. Precautions are given to keep parts clean and prevent damage from contaminants.
This document provides instructions for removing and installing the valve mechanism cover base and rocker shaft on a 320D LRR excavator with a C6.4 engine. The removal procedure details removing clips, harnesses, nuts and bolts to detach the cover base. Installation involves cleaning parts, installing a new gasket, and reattaching with bolts. Separate sections provide steps for disassembling and assembling the rocker shaft, including removing retaining rings, arms and springs. Precautions are given to prevent contamination of parts.
This document provides instructions for removing and installing the valve mechanism cover base and rocker shaft on a 320D LRR excavator with a C6.4 engine. The removal procedure details removing clips, harnesses, nuts and bolts to detach the cover base. Installation involves cleaning parts, installing a new gasket, and reattaching with bolts. Separate sections provide steps for disassembling the rocker shaft into individual parts and reassembling it.
This document provides instructions for removing and installing the valve mechanism cover base and rocker shaft on a 320D LRR excavator with a C6.4 engine. The removal procedure details removing clips, harnesses, nuts and bolts to detach the cover base. Installation involves cleaning parts, installing a new gasket, and reattaching with bolts. Separate sections provide steps for disassembling and assembling the rocker shaft, including removing retaining rings, arms and springs. Precautions are given to prevent contamination of parts.
This document provides instructions for removing and installing the flywheel and flywheel housing on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like the flywheel, flywheel ring gear, flywheel housing seal, and installing replacement parts. The document contains diagrams to illustrate the procedures.
This document provides instructions for removing and installing the flywheel and flywheel housing on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove the flywheel, flywheel housing, rear crankshaft seal, and installing replacements. Safety notices are provided to keep parts clean and contain fluids.
This document provides instructions for removing and installing the flywheel and flywheel housing on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like the flywheel, flywheel ring gear, flywheel housing seal, and installing replacement parts. The document contains diagrams to illustrate the procedures.
The document provides instructions for removing and installing a flywheel on a 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like the muffler brackets and flywheel bolts. Instructions are given for removing the flywheel itself using a lifting device and forcing bolts. Reinstalling involves cleaning surfaces, applying retaining compound, and torquing bolts to the specified value. The process for removing and installing the crankshaft rear seal and flywheel housing are also summarized.
The document provides instructions for removing and installing the flywheel on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like the muffler brackets and flywheel bolts. Lifting devices are needed due to the flywheel's 50 kg weight. Instructions are given for removing the ring gear from the flywheel as well as installing a new wear sleeve and rear oil seal. Overall, the document contains detailed removal and installation steps for servicing the flywheel assembly.
This document provides instructions for removing and installing the valve mechanism cover base and rocker shaft on a 320D LRR excavator with a C6.4 engine. The removal procedure details removing clips, harnesses, nuts and bolts to detach the cover base. Installation involves cleaning parts, installing a new gasket, and reattaching with bolts. Separate sections provide steps for disassembling and assembling the rocker shaft, including removing retaining rings, arms and springs. Precautions are given to prevent contamination of parts.
This document provides instructions for removing and installing the valve mechanism cover base and rocker shaft on a 320D LRR excavator with a C6.4 engine. The removal procedure details removing clips, harnesses, nuts and bolts to detach the cover base. Installation involves cleaning parts, installing a new gasket, and reattaching with bolts. Separate sections provide steps for disassembling the rocker shaft into individual parts and reassembling it.
This document provides instructions for removing and installing the valve mechanism cover base and rocker shaft on a 320D LRR excavator with a C6.4 engine. The removal procedure details removing clips, harnesses, nuts and bolts to detach the cover base. Installation involves cleaning parts, installing a new gasket, and reattaching with bolts. Separate sections provide steps for disassembling and assembling the rocker shaft, including removing retaining rings, arms and springs. Precautions are given to prevent contamination of parts.
This document provides instructions for removing and installing the flywheel and flywheel housing on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like the flywheel, flywheel ring gear, flywheel housing seal, and installing replacement parts. The document contains diagrams to illustrate the procedures.
This document provides instructions for removing and installing the flywheel and flywheel housing on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove the flywheel, flywheel housing, rear crankshaft seal, and installing replacements. Safety notices are provided to keep parts clean and contain fluids.
This document provides instructions for removing and installing the flywheel and flywheel housing on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like the flywheel, flywheel ring gear, flywheel housing seal, and installing replacement parts. The document contains diagrams to illustrate the procedures.
The document provides instructions for removing and installing a flywheel on a 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like the muffler brackets and flywheel bolts. Instructions are given for removing the flywheel itself using a lifting device and forcing bolts. Reinstalling involves cleaning surfaces, applying retaining compound, and torquing bolts to the specified value. The process for removing and installing the crankshaft rear seal and flywheel housing are also summarized.
The document provides instructions for removing and installing the flywheel on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like the muffler brackets and flywheel bolts. Lifting devices are needed due to the flywheel's 50 kg weight. Instructions are given for removing the ring gear from the flywheel as well as installing a new wear sleeve and rear oil seal. Overall, the document contains detailed removal and installation steps for servicing the flywheel assembly.
The document provides instructions for removing and installing the flywheel on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like the muffler brackets and flywheel bolts. Lifting devices are needed due to the flywheel's 50 kg weight. Instructions are given for removing the ring gear from the flywheel as well as installing a new wear sleeve and rear oil seal. Overall, the document contains detailed removal and installation steps for servicing the flywheel assembly.
Caterpillar cat 320 d lrr excavator (prefix ejt) service repair manual (ejt00...dkdmidkkdk
The document provides instructions for removing and installing a flywheel housing on a 320D LRR excavator. It describes removing the electric starting motor, flywheel, bolts and washers securing the housing. It notes the housing weighs approximately 29 kg. It also describes installing a new oil seal during reinstallation using special tools and reinstalling the flywheel.
The document provides instructions for removing and installing a flywheel housing on a 320D LRR excavator. It describes removing the electric starting motor, flywheel, bolts and washers securing the housing. It notes the housing weighs approximately 29 kg. It also describes installing a new oil seal during reinstallation using special tools and reinstalling the flywheel.
The document provides instructions for removing and installing the flywheel on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like the muffler brackets and flywheel bolts. Lifting devices are needed due to the flywheel's 50 kg weight. Instructions are given for removing the ring gear from the flywheel as well as installing a new crankshaft rear seal and wear sleeve. Reinstallation involves cleaning surfaces, applying retaining compound, and reinstalling bolts and brackets.
The document provides instructions for removing and installing a flywheel housing on a 320D LRR excavator. It describes removing the electric starting motor, flywheel, bolts and washers securing the housing. It notes the housing weighs approximately 29 kg. It also details installing the housing, ensuring all parts are clean, and reinstalling the flywheel and electric starting motor.
The document provides instructions for removing and installing a flywheel on a 320D LRR excavator with a C6.4 engine. It describes using various tools to remove the flywheel, flywheel housing, and rear crankshaft seal. Instructions are given for cleaning and preparing the components, installing a new rear seal and wear sleeve, and securing the flywheel housing and flywheel. Similar procedures are outlined for removing and installing the crankshaft pulley.
The document provides instructions for removing and installing the flywheel on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove the flywheel bolts and housing, then lifting the flywheel off. Reinstallation involves cleaning surfaces, installing with bolts and checking runout. Removing the rear crankshaft seal and installing a new one is also described.
The document provides instructions for removing and installing the flywheel on a 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like the muffler brackets and flywheel bolts. Instructions are given for removing the flywheel itself using a lifting device and forcing bolts. Reinstallation involves cleaning surfaces, applying retaining compound, and tightening bolts to the specified torque.
Caterpillar cat 320 d lrr excavator (prefix ejt) service repair manual (ejt00...fjjsekkdmme
This document provides instructions for removing and installing the flywheel and crankshaft pulley on a 320D LRR excavator with a C6.4 engine. The flywheel removal procedure involves using link brackets and forcing bolts to lift the flywheel off the crankshaft. The crankshaft pulley is removed using a combination puller tool. Both components are installed by reversing the removal process and tightening to the specified torques.
Caterpillar cat 320 d lrr excavator (prefix ejt) service repair manual (ejt00...fjsekdmmeed
The document provides instructions for removing and installing the flywheel and crankshaft pulley on a 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like the flywheel, flywheel housing, and crankshaft pulley. Detailed steps and illustrations are provided for disassembling and reassembling these parts, including cleaning, inspecting, and applying sealants to mating surfaces. Safety notices advise keeping parts clean and containing fluids.
- The document provides instructions to remove and install a crankshaft pulley on a Caterpillar C6.4 engine.
- To remove the pulley, use a combination puller tool to pull the pulley off the crankshaft. Clean any contaminants from the pulley and crankshaft mating surfaces.
- To install the pulley, apply a retaining compound to the crankshaft and pulley mating surfaces. Use a 46mm socket and installer tool to press the pulley onto the crankshaft. Reinstall the belt once the pulley is installed.
Caterpillar Cat 320D L Excavator (Prefix PHX) Service Repair Manual (PHX00001...xiapokang564341
- The document provides instructions to remove and install a crankshaft pulley on a Caterpillar C6.4 engine.
- To remove the pulley, use a combination puller tool to pull the pulley off the crankshaft. Clean any contaminants from the pulley and crankshaft mating surfaces.
- To install the pulley, apply a retaining compound to the crankshaft and pulley mating surfaces. Use a 46mm socket and installer tool to press the pulley onto the crankshaft. Reinstall the belt once the pulley is installed.
- The document provides instructions to remove and install a crankshaft pulley on a Caterpillar C6.4 engine.
- To remove the pulley, use a combination puller tool to pull the pulley off the crankshaft. Clean any contaminants from the pulley and crankshaft mating surfaces.
- To install the pulley, apply a retaining compound to the crankshaft and pulley mating surfaces. Use a 46mm socket and installer tool to press the pulley onto the crankshaft. Reinstall the belt once the pulley is installed.
- The document provides instructions to remove and install a crankshaft pulley on a Caterpillar C6.4 engine.
- To remove the pulley, use a combination puller tool to pull the pulley off the crankshaft. Clean any contaminants from the pulley and crankshaft mating surfaces.
- To install the pulley, apply a retaining compound to the crankshaft and pulley mating surfaces. Use a 46mm socket and installer tool to press the pulley onto the crankshaft. Reinstall the belt once the pulley is installed.
Caterpillar Cat 320D L Excavator (Prefix PHX) Service Repair Manual (PHX00001...sijipang18046
- The document provides instructions to remove and install a crankshaft pulley on a Caterpillar C6.4 engine.
- To remove the pulley, use a combination puller tool to pull the pulley off the crankshaft. Clean any contaminants from the pulley and crankshaft mating surfaces.
- To install the pulley, apply a retaining compound to the crankshaft and pulley mating surfaces. Use a 46mm socket and installer tool to press the pulley onto the crankshaft. Reinstall the belt once the pulley is installed.
Caterpillar Cat 320D L Excavator (Prefix PHX) Service Repair Manual (PHX00001...hvy7sbkw8e
The document provides instructions for removing and installing a flywheel housing on an excavator. It describes:
1) Removing bolts and washers to separate the flywheel housing from the cylinder block.
2) Using lifting equipment to remove the heavy flywheel housing.
3) Removing the gasket between the housing and cylinder block.
The document provides instructions for removing and installing a flywheel housing on an excavator. Key steps include:
1. Removing bolts and washers to separate the flywheel housing from the cylinder block.
2. Lifting the flywheel housing off using tooling and a lifting device, as it weighs approximately 29 kg.
3. Removing the gasket between the flywheel housing and cylinder block.
The document provides instructions for removing and installing various engine components on a Caterpillar 320D L excavator including:
- Removing the flywheel using link brackets and forcing bolts.
- Removing the crankshaft rear seal using a slide hammer puller and seal distorter.
- Installing a new crankshaft rear seal with a wear sleeve using an installer, locator, bolts and washer.
- Removing the flywheel housing using link brackets and lifting it off with bolts and washers.
- Installing a new oil seal and bolting the flywheel housing back on with new gaskets.
- Removing the crankshaft pulley using a combination puller
Caterpillar Cat 320D L Excavator (Prefix MGG) Service Repair Manual (MGG00001...xiapokang564341
The document provides instructions for removing and installing various engine components on a Caterpillar 320D L excavator including:
- Removing the flywheel using link brackets and forcing bolts.
- Removing the crankshaft rear seal using a slide hammer puller and seal distorter.
- Installing a new crankshaft rear seal with a wear sleeve using an installer, locator, bolts and washer.
- Removing the flywheel housing using link brackets and lifting it off with bolts and washers.
- Installing a new oil seal and bolting the flywheel housing back on with new gaskets.
- Removing the crankshaft pulley using a combination puller
Caterpillar Cat 320D L Excavator (Prefix MGG) Service Repair Manual (MGG00001...sijipang18046
The document provides instructions for removing and installing various engine components on a Caterpillar 320D L excavator including:
- Removing the flywheel using link brackets and forcing bolts.
- Removing the crankshaft rear seal using a slide hammer puller and seal distorter.
- Installing a new crankshaft rear seal with a wear sleeve using an installer, locator, bolts and washer.
- Removing the flywheel housing using link brackets and lifting it off with bolts and washers.
- Installing a new oil seal and bolting the flywheel housing back on with new gaskets.
- Removing the crankshaft pulley using a combination puller
This document provides instructions for servicing components of a Caterpillar 330D L excavator engine. It describes procedures for removing and installing the cylinder head, camshaft, lifter group, and associated parts. The steps include draining coolant, removing mounting hardware, lifting components with tools, applying lubricant, and torquing fasteners to specified values. Safety notices are provided to keep parts clean and prevent damage during removal and installation.
1. The document provides instructions for assembling and installing the swing drive of an excavator model 330D L.
2. It describes 30 steps for assembling bearings, gears, shafts, seals, and housings and attaching the assembly to the excavator frame using bolts.
3. Proper cleaning, lubrication, and heating of parts is emphasized to ensure correct assembly. Tools, torque specifications, and maintenance procedures are also outlined.
More Related Content
Similar to Caterpillar Cat 320D LRR Excavator (Prefix ZGB) Service Repair Manual (ZGB00001 and up).pdf
The document provides instructions for removing and installing the flywheel on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like the muffler brackets and flywheel bolts. Lifting devices are needed due to the flywheel's 50 kg weight. Instructions are given for removing the ring gear from the flywheel as well as installing a new wear sleeve and rear oil seal. Overall, the document contains detailed removal and installation steps for servicing the flywheel assembly.
Caterpillar cat 320 d lrr excavator (prefix ejt) service repair manual (ejt00...dkdmidkkdk
The document provides instructions for removing and installing a flywheel housing on a 320D LRR excavator. It describes removing the electric starting motor, flywheel, bolts and washers securing the housing. It notes the housing weighs approximately 29 kg. It also describes installing a new oil seal during reinstallation using special tools and reinstalling the flywheel.
The document provides instructions for removing and installing a flywheel housing on a 320D LRR excavator. It describes removing the electric starting motor, flywheel, bolts and washers securing the housing. It notes the housing weighs approximately 29 kg. It also describes installing a new oil seal during reinstallation using special tools and reinstalling the flywheel.
The document provides instructions for removing and installing the flywheel on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like the muffler brackets and flywheel bolts. Lifting devices are needed due to the flywheel's 50 kg weight. Instructions are given for removing the ring gear from the flywheel as well as installing a new crankshaft rear seal and wear sleeve. Reinstallation involves cleaning surfaces, applying retaining compound, and reinstalling bolts and brackets.
The document provides instructions for removing and installing a flywheel housing on a 320D LRR excavator. It describes removing the electric starting motor, flywheel, bolts and washers securing the housing. It notes the housing weighs approximately 29 kg. It also details installing the housing, ensuring all parts are clean, and reinstalling the flywheel and electric starting motor.
The document provides instructions for removing and installing a flywheel on a 320D LRR excavator with a C6.4 engine. It describes using various tools to remove the flywheel, flywheel housing, and rear crankshaft seal. Instructions are given for cleaning and preparing the components, installing a new rear seal and wear sleeve, and securing the flywheel housing and flywheel. Similar procedures are outlined for removing and installing the crankshaft pulley.
The document provides instructions for removing and installing the flywheel on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove the flywheel bolts and housing, then lifting the flywheel off. Reinstallation involves cleaning surfaces, installing with bolts and checking runout. Removing the rear crankshaft seal and installing a new one is also described.
The document provides instructions for removing and installing the flywheel on a 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like the muffler brackets and flywheel bolts. Instructions are given for removing the flywheel itself using a lifting device and forcing bolts. Reinstallation involves cleaning surfaces, applying retaining compound, and tightening bolts to the specified torque.
Caterpillar cat 320 d lrr excavator (prefix ejt) service repair manual (ejt00...fjjsekkdmme
This document provides instructions for removing and installing the flywheel and crankshaft pulley on a 320D LRR excavator with a C6.4 engine. The flywheel removal procedure involves using link brackets and forcing bolts to lift the flywheel off the crankshaft. The crankshaft pulley is removed using a combination puller tool. Both components are installed by reversing the removal process and tightening to the specified torques.
Caterpillar cat 320 d lrr excavator (prefix ejt) service repair manual (ejt00...fjsekdmmeed
The document provides instructions for removing and installing the flywheel and crankshaft pulley on a 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like the flywheel, flywheel housing, and crankshaft pulley. Detailed steps and illustrations are provided for disassembling and reassembling these parts, including cleaning, inspecting, and applying sealants to mating surfaces. Safety notices advise keeping parts clean and containing fluids.
- The document provides instructions to remove and install a crankshaft pulley on a Caterpillar C6.4 engine.
- To remove the pulley, use a combination puller tool to pull the pulley off the crankshaft. Clean any contaminants from the pulley and crankshaft mating surfaces.
- To install the pulley, apply a retaining compound to the crankshaft and pulley mating surfaces. Use a 46mm socket and installer tool to press the pulley onto the crankshaft. Reinstall the belt once the pulley is installed.
Caterpillar Cat 320D L Excavator (Prefix PHX) Service Repair Manual (PHX00001...xiapokang564341
- The document provides instructions to remove and install a crankshaft pulley on a Caterpillar C6.4 engine.
- To remove the pulley, use a combination puller tool to pull the pulley off the crankshaft. Clean any contaminants from the pulley and crankshaft mating surfaces.
- To install the pulley, apply a retaining compound to the crankshaft and pulley mating surfaces. Use a 46mm socket and installer tool to press the pulley onto the crankshaft. Reinstall the belt once the pulley is installed.
- The document provides instructions to remove and install a crankshaft pulley on a Caterpillar C6.4 engine.
- To remove the pulley, use a combination puller tool to pull the pulley off the crankshaft. Clean any contaminants from the pulley and crankshaft mating surfaces.
- To install the pulley, apply a retaining compound to the crankshaft and pulley mating surfaces. Use a 46mm socket and installer tool to press the pulley onto the crankshaft. Reinstall the belt once the pulley is installed.
- The document provides instructions to remove and install a crankshaft pulley on a Caterpillar C6.4 engine.
- To remove the pulley, use a combination puller tool to pull the pulley off the crankshaft. Clean any contaminants from the pulley and crankshaft mating surfaces.
- To install the pulley, apply a retaining compound to the crankshaft and pulley mating surfaces. Use a 46mm socket and installer tool to press the pulley onto the crankshaft. Reinstall the belt once the pulley is installed.
Caterpillar Cat 320D L Excavator (Prefix PHX) Service Repair Manual (PHX00001...sijipang18046
- The document provides instructions to remove and install a crankshaft pulley on a Caterpillar C6.4 engine.
- To remove the pulley, use a combination puller tool to pull the pulley off the crankshaft. Clean any contaminants from the pulley and crankshaft mating surfaces.
- To install the pulley, apply a retaining compound to the crankshaft and pulley mating surfaces. Use a 46mm socket and installer tool to press the pulley onto the crankshaft. Reinstall the belt once the pulley is installed.
Caterpillar Cat 320D L Excavator (Prefix PHX) Service Repair Manual (PHX00001...hvy7sbkw8e
The document provides instructions for removing and installing a flywheel housing on an excavator. It describes:
1) Removing bolts and washers to separate the flywheel housing from the cylinder block.
2) Using lifting equipment to remove the heavy flywheel housing.
3) Removing the gasket between the housing and cylinder block.
The document provides instructions for removing and installing a flywheel housing on an excavator. Key steps include:
1. Removing bolts and washers to separate the flywheel housing from the cylinder block.
2. Lifting the flywheel housing off using tooling and a lifting device, as it weighs approximately 29 kg.
3. Removing the gasket between the flywheel housing and cylinder block.
The document provides instructions for removing and installing various engine components on a Caterpillar 320D L excavator including:
- Removing the flywheel using link brackets and forcing bolts.
- Removing the crankshaft rear seal using a slide hammer puller and seal distorter.
- Installing a new crankshaft rear seal with a wear sleeve using an installer, locator, bolts and washer.
- Removing the flywheel housing using link brackets and lifting it off with bolts and washers.
- Installing a new oil seal and bolting the flywheel housing back on with new gaskets.
- Removing the crankshaft pulley using a combination puller
Caterpillar Cat 320D L Excavator (Prefix MGG) Service Repair Manual (MGG00001...xiapokang564341
The document provides instructions for removing and installing various engine components on a Caterpillar 320D L excavator including:
- Removing the flywheel using link brackets and forcing bolts.
- Removing the crankshaft rear seal using a slide hammer puller and seal distorter.
- Installing a new crankshaft rear seal with a wear sleeve using an installer, locator, bolts and washer.
- Removing the flywheel housing using link brackets and lifting it off with bolts and washers.
- Installing a new oil seal and bolting the flywheel housing back on with new gaskets.
- Removing the crankshaft pulley using a combination puller
Caterpillar Cat 320D L Excavator (Prefix MGG) Service Repair Manual (MGG00001...sijipang18046
The document provides instructions for removing and installing various engine components on a Caterpillar 320D L excavator including:
- Removing the flywheel using link brackets and forcing bolts.
- Removing the crankshaft rear seal using a slide hammer puller and seal distorter.
- Installing a new crankshaft rear seal with a wear sleeve using an installer, locator, bolts and washer.
- Removing the flywheel housing using link brackets and lifting it off with bolts and washers.
- Installing a new oil seal and bolting the flywheel housing back on with new gaskets.
- Removing the crankshaft pulley using a combination puller
Similar to Caterpillar Cat 320D LRR Excavator (Prefix ZGB) Service Repair Manual (ZGB00001 and up).pdf (20)
This document provides instructions for servicing components of a Caterpillar 330D L excavator engine. It describes procedures for removing and installing the cylinder head, camshaft, lifter group, and associated parts. The steps include draining coolant, removing mounting hardware, lifting components with tools, applying lubricant, and torquing fasteners to specified values. Safety notices are provided to keep parts clean and prevent damage during removal and installation.
1. The document provides instructions for assembling and installing the swing drive of an excavator model 330D L.
2. It describes 30 steps for assembling bearings, gears, shafts, seals, and housings and attaching the assembly to the excavator frame using bolts.
3. Proper cleaning, lubrication, and heating of parts is emphasized to ensure correct assembly. Tools, torque specifications, and maintenance procedures are also outlined.
Caterpillar Cat 330C L Excavator (Prefix MCA) Service Repair Manual (MCA00001...fjkdksmmdm
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavator models. The disassembly process involves removing 28 different components in a specific sequence. The assembly process reverses the disassembly steps and includes applying thread lock compound and lubricating components before reassembly. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar Cat 330C L Excavator (Prefix KDD) Service Repair Manual (KDD00001...fjkdksmmdm
This document provides instructions for disassembling and assembling a 330C excavator travel motor. It describes 28 steps to disassemble the motor by removing components like the head, port plate, springs, brake piston, plates, and bearings. It then describes 13 steps for assembly, including installing seals, bearings, springs, cam plate, and rotating assembly into the housing. Special tools are listed and safety notices are provided throughout regarding cleaning, pressurized air, and spring loading.
Caterpillar Cat 330C L Excavator (Prefix JNK) Service Repair Manual (JNK00001...fjkdksmmdm
The document provides instructions for assembling and installing a piston motor (hydraulic fan). It is a 3 page document that details 20 steps for assembly, including installing various components like bearings, seals, springs and retaining rings. It then provides 11 steps for installing the assembled piston motor and attaching hoses and guards. Proper cleaning and lubrication of parts is emphasized.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B1K) Service Repair Manual (B1K0000...fjkdksmmdm
This document provides instructions for installing a camshaft on a Caterpillar 330C FM excavator engine. It begins by listing the required tools. The instructions then state to clean all parts, set the number 1 piston to top center, and align the camshaft and idler gears. The camshaft is then lubricated and inserted into the cylinder block. The thrust plate and bolts are installed and tightened. Lifters are repositioned and the procedure ends by installing the front cover and rocker arm assembly.
Caterpillar Cat 330C L Excavator (Prefix JCD) Service Repair Manual (JCD00001...fjkdksmmdm
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavators. It outlines 28 steps for disassembly, removing components like the head, springs, brake piston, and bearings. It then outlines 13 steps for assembly, replacing seals and installing components in the reverse order of disassembly, taking care to mark parts and return them to their original positions. Special tools are listed that may be required for tasks like removing races and seals.
This document provides instructions for disassembling and assembling the travel motor on a 330C excavator. It describes 28 steps to disassemble the motor by removing components like the head, port plate, springs, brake piston, plates, and seals. It then describes 15 steps for reassembling the motor and installing components in the reverse order, making sure to clean parts and apply thread lock compound as needed. Tools required include retaining ring pliers, a bearing puller, an eyebolt, and an adapter.
Caterpillar Cat 330C L Excavator (Prefix GKX) Service Repair Manual (GKX00001...fjkdksmmdm
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of 330C and 330C L excavator models.
2) It details 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components. Special tools are required.
3) It then lists 28 steps for reassembly, providing notes on cleaning, lubrication, and proper installation of O-rings and other parts to ensure correct assembly. The keys and notches must be properly aligned and torques applied to specifications.
Caterpillar Cat 330C L Excavator (Prefix DKY) Service Repair Manual (DKY00001...fjkdksmmdm
- The document provides disassembly and assembly instructions for the travel motor of a 330C L excavator.
- It describes 28 steps to disassemble the travel motor by removing components like the head, plates, seals, and bearing races.
- It then describes 28 steps for assembling the travel motor, providing notes on cleaning, applying sealant, and ensuring proper alignment of components like the cam plate and keys.
- Tools required include retaining ring pliers, a bearing puller, threaded rod, and eyebolt for installation and removal of components.
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavator models. It describes 28 steps to disassemble the motor by removing components like the head, port plate, springs, brake piston, plates, and bearings. It then describes 13 steps for assembly, including installing seals, bearings, springs, and securing the rotating assembly back into the housing. Special tools are listed and safety notices are provided throughout regarding handling pressurized components and ensuring cleanliness during reassembly.
Caterpillar Cat 330C L Excavator (Prefix CYA) Service Repair Manual (CYA00001...fjkdksmmdm
This document provides instructions for disassembling and assembling the travel motor on a 330C L excavator. The disassembly process involves removing 28 components including the head, port plate, springs, brake piston, plates, and seals. The assembly process reverses the disassembly steps and includes installing seals, bearings, and retaining rings in their proper positions. Cleanliness is important during assembly to prevent contamination.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B3M) Service Repair Manual (B3M0000...fjkdksmmdm
This document provides instructions for releasing hydraulic pressure from the systems of a 330C FM excavator before performing service. It describes:
- Releasing pressure from a single circuit by moving the relevant control to its full stroke position with the engine on and activation lever unlocked.
- Releasing pressure from multiple circuits by repeating this process for each circuit needing service.
- Additional steps like starting the engine briefly with no control movement to further release pressure across systems.
The document aims to safely depressurize hydraulic lines and components before disconnection or removal during maintenance.
This document provides instructions for disassembling and assembling the travel motor on a 330C excavator. It describes 28 steps to disassemble the motor by removing components like the head, port plate, bearings, brake piston, plates, and seals. It then describes 13 steps for assembling the motor, replacing all seals and installing components in reverse order of removal. Special tools are required and cleanliness is important when handling parts.
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavator models. The summary is:
1. The travel motor disassembly procedure involves removing 28 components including the head, port plate, springs, brake piston, plates, and seals.
2. Travel motor assembly requires installing components in reverse order, applying thread lock compound and oil, and torquing bolts to specified values.
3. Special tools are required to remove races, seals, and retainers, and care must be taken to avoid damaging parts and ensure proper alignment of keys and plates.
This document provides instructions for assembling a piston motor (hydraulic fan) with 20 steps. It involves installing various components like bearing cups, seals, pins, springs, pistons, and plates in the proper sequence and orientation. Safety notes are included to handle parts carefully and apply oil during assembly. The summary is complete in 3 sentences.
1) The document provides disassembly and assembly instructions for a travel motor on 330C and 330C L excavator models.
2) It describes 28 steps to disassemble the travel motor by removing components like the head, plates, seals, bearings, and housing covers.
3) It then lists 28 steps for reassembling the travel motor, replacing all seals and applying lubricant before reinstalling the components in reverse order of disassembly. Proper cleanliness and torque specifications are emphasized.
1) The document provides instructions for disassembling and assembling the travel motor of a 330C excavator.
2) It describes 28 steps to disassemble the travel motor by removing components like the head, port plate, springs, brake piston, plates, and seals.
3) It then lists 28 steps for reassembling the travel motor, placing components back in reverse order and noting alignment and torque specifications. Precise reassembly is emphasized for correct operation.
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of 330C and 330C L excavator models.
2) It details 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components. Special tools are required.
3) It then lists 28 steps for reassembly, providing notes on cleaning, lubrication, and proper installation of O-rings and other parts to ensure correct assembly. The keys and notches must be properly aligned and torques applied to specifications.
1) The document provides disassembly and assembly instructions for the travel motor of a 330C excavator.
2) It describes 28 steps to disassemble the travel motor by removing components like the head, springs, plates, and seals.
3) It then describes 29 steps for assembling the travel motor, including installing seals, plates, springs, and tightening bolts in the proper order and with specified torques.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D LRR EXCAVATOR ZGB
Configuration: 320D LRR Excavator ZGB00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02746415
Valve Mechanism Cover Base - Remove and Install
SMCS - 1120-010
Removal Procedure
Start By:
a. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install".
b. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3(W)
w
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
3. Illustration 1 g01375577
1. Remove clips (4).
2. Disconnect harness assembly (6).
3. Loosen nuts (2) and disconnect harness assembly (3).
4. Repeat Step 3 for the remaining electronic unit injectors.
5. Remove bolts (1).
6. Remove bolts (5). Remove valve mechanism cover base (7) and the gasket.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3(W)
w
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
4. Illustration 2 g01375577
1. Install a new gasket and position valve mechanism cover base (7). Install bolts (5).
2. Install bolts (1). Tighten bolts (1) to a torque of 18 ± 2 N·m (13 ± 1 lb ft).
3. Connect harness assembly (3) and tighten nuts (2).
4. Repeat Step 3 for the remaining electronic unit injectors.
5. Connect harness assembly (6).
6. Install clips (4).
End By:
a. Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines -
Install".
b. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Oct 31 23:02:32 UTC+0800 2020
3/3(W)
w
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D LRR EXCAVATOR ZGB
Configuration: 320D LRR Excavator ZGB00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02746912
Rocker Shaft and Pushrod - Remove
SMCS - 1102-011; 1208-011
Removal Procedure
Start By:
a. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: The fuel injection lines do not need to be removed in order to remove the rocker shaft and
pushrods.
1/2(W)
w
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
6. Illustration 1 g01375828
1. Loosen nuts (1) and disconnect harness assembly (2).
2. Repeat Step 13 for the remaining electronic unit injectors.
3. Disconnect harness assembly (3).
4. Remove bolts (4) and remove harness assembly (3).
Illustration 2 g01375847
5. Loosen nut (9). Loosen adjusting screw (11) by approximately one revolution.
6. Repeat Step 5 for the remaining rocker arms.
7. Loosen bolts (10). Do not remove bolts (10) at this time.
8. Loosen bolts (8). Do not remove bolts (8) at this time.
9. Remove bolts (10).
10. Remove bolts (8).
11. Remove rocker shaft assembly (5).
12. Remove pushrods (6).
13. Remove bridges (7) and the caps.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Oct 31 23:03:28 UTC+0800 2020
2/2(W)
w
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
7. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D LRR EXCAVATOR ZGB
Configuration: 320D LRR Excavator ZGB00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02746773
Rocker Shaft - Disassemble
SMCS - 1102-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1859 Retaining Ring Pliers 1
B 1P-0510 Driver Gp 1
Start By:
a. Remove the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrods - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior
of the components should be thoroughly cleaned. This will help to prevent dirt from entering the
internal mechanism. Precision components can be damaged by contaminants or by dirt. Perform
disassembly procedures on a clean work surface. Keep components covered and protected at all
times.
1/3(W)
w
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
8. Illustration 1 g01375734
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove bolt (1) from shaft assembly (5).
2. Remove pipe (6) from shaft assembly (5).
3. Use Tooling (A) in order to remove retaining ring (2) from shaft assembly (5).
4. Remove washer (7) from shaft assembly (5).
5. Remove arm assembly (3) from shaft assembly (5).
6. Remove bracket (8) from shaft assembly (5).
7. Remove arm assembly (4) from shaft assembly (5).
8. Remove spring (9) from shaft assembly (5).
2/3(W)
w
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
9. Illustration 2 g01375874
9. If necessary, use Tooling (B) in order to remove bushing (10) from arm assemblies (3) and
(4).
10. Repeat Steps 3 through 9 for the remaining rocker shaft assembly.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Oct 31 23:04:23 UTC+0800 2020
3/3(W)
w
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D LRR EXCAVATOR ZGB
Configuration: 320D LRR Excavator ZGB00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02746816
Rocker Shaft - Assemble
SMCS - 1102-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1859 Retaining Ring Pliers 1
B 1P-0510 Driver Gp 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning
fluid. Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be
deposited on the parts which may cause trouble. Inspect all parts. If any parts are worn or
damaged, use new parts for replacement. Dirt and other contaminants can damage the precision
component. Perform assembly procedures on a clean work surface. Keep components covered and
protected at all times.
1/3(W)
w
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
11. Illustration 1 g01375874
1. If necessary, Use Tooling (B) in order to install bushing (10) into arm assemblies (4) and
(3).
Illustration 2 g01375734
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
2. Install spring (9) onto shaft assembly (5).
3. Install arm assembly (4) onto shaft assembly (5).
4. Install bracket (8) onto shaft assembly (5).
5. Install arm assembly (3) onto shaft assembly (5).
6. Install washer (7) onto shaft assembly (5).
2/3(W)
w
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
12. 7. Use Tooling (A) in order to install retaining ring (2) onto shaft assembly (5).
8. Repeat Steps 1 through 7 for the remaining rocker shaft assembly.
9. Install pipe (6) onto shaft assembly (5).
10. Install bolt (1). Tighten bolts (1) to a torque of 74 ± 5 N·m (55 ± 4 lb ft).
End By:
a. Install the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrods - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Oct 31 23:05:19 UTC+0800 2020
3/3(W)
w
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D LRR EXCAVATOR ZGB
Configuration: 320D LRR Excavator ZGB00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02746971
Rocker Shaft and Pushrod - Install
SMCS - 1102-012; 1208-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01375847
1. Install bridges (7) and the caps.
2. Install pushrods (6).
3. Position rocker shaft assembly (5).
1/2(W)
w
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
14. 4. Position bolts (8). Do not tighten bolts (8) at this time.
5. Position bolts (10). Do not tighten bolts (10) at this time.
6. Tighten bolts (8) to a torque of 18 ± 2 N·m (13 ± 1 lb ft).
7. Tighten bolts (10) to a torque of 18 ± 2 N·m (13 ± 1 lb ft).
8. Adjust adjusting screw (11) so that bridge (7) contacts both of the valve ends evenly.
Tighten nut (9) to a torque of 4 ± 1 N·m (35 ± 9 lb in).
9. Repeat Step 8 for the remaining rocker arms.
Illustration 2 g01375828
10. Position harness assembly (3) and install bolts (4).
11. Connect harness assembly (3).
12. Connect harness assembly (2) and tighten nuts (1).
13. Repeat Step 12 for the remaining electronic unit injectors.
14. Adjust the inlet valve lash to 0.250 mm (0.0098 inch). Adjust the exhaust valve lash to
0.400 mm (0.0157 inch). Refer to Testing and Adjusting, "Engine Valve Lash -
Test/Adjust".
End By:
a. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Oct 31 23:06:15 UTC+0800 2020
2/2(W)
w
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D LRR EXCAVATOR ZGB
Configuration: 320D LRR Excavator ZGB00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02746505
Cylinder Head - Remove
SMCS - 1100-011
Removal Procedure
Start By:
a. Remove the valve mechanism cover base. Refer to Disassembly and Assembly, "Valve Mechanism
Cover Base - Remove and Install".
b. Remove the rocker shaft and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and
Pushrods - Remove".
c. Remove the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit Injector -
Remove".
d. If necessary, remove the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold
- Remove and Install".
e. If necessary, remove the inlet manifold. Refer to Disassembly and Assembly, "Inlet Manifold -
Remove and Install".
f. If necessary, remove the water temperature regulator. Refer to Disassembly and Assembly, "Water
Temperature Regulator - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
1/3(W)
w
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
16. of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01375619
1. Disconnect hose (1).
Illustration 2 g01375622
2. Disconnect tube assembly (2).
3. Remove bolts (3). Disconnect tube assembly (4) and remove the gasket.
2/3(W)
w
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
17. Illustration 3 g01375641
Illustration 4 g01375653
4. Attach a suitable lifting device to cylinder head (5). The weight of cylinder head (5) is approximately
113 kg (250 lb).
5. Loosen cylinder head bolts (6) in the sequence that is shown in Illustration 4.
6. Use the suitable lifting device in order to remove cylinder head (5) and the gasket.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Oct 31 23:07:11 UTC+0800 2020
3/3(W)
w
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D LRR EXCAVATOR ZGB
Configuration: 320D LRR Excavator ZGB00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02746742
Cylinder Head - Install
SMCS - 1100-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01375641
1/3(W)
w
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
19. Illustration 2 g01375708
1. Install a new gasket. Attach a suitable lifting device to cylinder head (5). The weight of cylinder head
(5) is approximately 113 kg (250 lb). Use the suitable lifting device in order to position cylinder head
(5) on the engine block.
2. Tighten bolts (6) in the sequence that is shown in Illustration 2 to a torque of 137 ± 5 N·m
(101 ± 4 lb ft).
Illustration 3 g01375622
3. Install a new gasket and connect tube assembly (4). Install bolts (3).
4. Connect tube assembly (2).
2/3(W)
w
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
20. Illustration 4 g01375619
5. Connect hose (1).
End By:
a. If necessary, install the water temperature regulator. Refer to Disassembly and Assembly, "Water
Temperature Regulator - Remove and Install".
b. If necessary, install the inlet manifold. Refer to Disassembly and Assembly, "Inlet Manifold -
Remove and Install".
c. If necessary, install the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold -
Remove and Install".
d. Install the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit Injector -
Install".
e. Install the rocker shaft and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and
Pushrods - Install".
f. Install the valve mechanism cover base. Refer to Disassembly and Assembly, "Valve Mechanism
Cover Base - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Oct 31 23:08:06 UTC+0800 2020
3/3(W)
w
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D LRR EXCAVATOR ZGB
Configuration: 320D LRR Excavator ZGB00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02751804
Lifter Group - Remove and Install
SMCS - 1209-010
Removal Procedure
Start By:
a. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00610824
1/3(W)
w
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
22. Illustration 2 g00532061
1. Use a magnet in order to remove valve lifter (1) from the engine cylinder block, as shown.
Put identification marks on valve lifters (1) for installation purposes.
2. Repeat Step 1 for the remainder of valve lifters (1).
Illustration 3 g00613675
View (X) shows a good contact pattern. Views (Y) and (Z) show bad contact patterns.
Note: Check the valve lifters for wear.
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8T-2998 Lubricant 1
2/3(W)
w
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 4 g00532061
1. Apply Tooling (A) to valve lifter (1) prior to installation. Install valve lifter (1) in the
original location in the engine cylinder block.
2. Repeat Step 1 for the remainder of the valve lifters.
End By:
a. Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Oct 31 23:09:02 UTC+0800 2020
3/3(W)
w
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D LRR EXCAVATOR ZGB
Configuration: 320D LRR Excavator ZGB00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02751903
Camshaft - Remove and Install
SMCS - 1210-010
Removal Procedure
Start By:
a. Remove the front housing. Refer to Disassembly and Assembly, " Housing (Front) -
Remove".
b. Remove the rocker shaft assembly and the pushrods. Refer to Disassembly and Assembly,
"Rocker Shaft and Pushrod - Remove".
c. Remove the oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and
Install".
Note: In this removal procedure, the engine needs to be placed in the upside-down position. This
will allow the lifters to remain in position after the camshaft is removed.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/5(W)
w
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
26. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00569371
Note: Ensure that the marks on the timing gears are in alignment. Align the "3" mark on fuel
injection drive gear (A) with the "33" mark on idler gear (B). Make an alignment of the "22" mark
on camshaft gear (C) with the "2" mark on idler gear (B). Align the "1" mark on crankshaft gear
(D) with the "11" mark on idler gear (B). The No. 1 cylinder is at the top center position when
these marks are in alignment.
1. Rotate the engine at 180 degrees in order to place the engine in the upside-down position.
This will ease the removal of the camshaft.
2/5(W)
w
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...