1. The document provides instructions for assembling and installing the swing drive of an excavator model 330D L.
2. It describes 30 steps for assembling bearings, gears, shafts, seals, and housings and attaching the assembly to the excavator frame using bolts.
3. Proper cleaning, lubrication, and heating of parts is emphasized to ensure correct assembly. Tools, torque specifications, and maintenance procedures are also outlined.
The document provides instructions for removing the swing gear and bearing from an excavator undercarriage frame. The procedure involves:
1. Removing all grease from the swing gear and bearing and placing it in a suitable container.
2. Marking the swing gear and bearing and frame for reassembly.
3. Using lifting equipment and link brackets to support the swing gear and bearing while removing bolts.
4. Removing the 280 kg swing gear and bearing assembly.
Caterpillar Cat 330D L Excavator (Prefix EDX) Service Repair Manual (EDX00001...shudun96087
The document provides instructions for removing the swing gear and bearing from an excavator undercarriage frame. The procedure involves:
1. Removing all grease from the swing gear and bearing and placing it in a suitable container.
2. Marking the swing gear and bearing and frame for reassembly.
3. Using lifting equipment and link brackets to support the swing gear and bearing while removing bolts.
4. Removing the 280 kg swing gear and bearing assembly.
Caterpillar Cat 330D L Excavator (Prefix EDX) Service Repair Manual (EDX00001...kesi7153062
The document provides installation instructions for assembling the swing drive of an excavator. It involves 30 steps including installing bearings and seals into the drive shaft assembly, installing gears and carriers, applying sealant and installing the ring gear and housing cover. Special tools and precautions are noted regarding cleanliness and bearing temperatures. Proper torque values and tightening procedures are specified for reinstalling the completed swing drive assembly into the excavator frame.
The document provides instructions for removing the swing gear and bearing from an excavator undercarriage frame. The procedure involves:
1. Removing all grease from the swing gear and bearing and placing it in a suitable container.
2. Marking the swing gear and bearing and frame for reassembly.
3. Using lifting equipment and link brackets to support the swing gear and bearing while removing bolts.
4. Removing the 280 kg swing gear and bearing assembly.
Caterpillar Cat 330D L Excavator (Prefix EDX) Service Repair Manual (EDX00001...cnp692569
The document provides instructions for removing the swing gear and bearing from an excavator undercarriage frame. The procedure involves:
1. Removing all grease from the swing gear and bearing.
2. Marking the swing gear and bearing and frame for reassembly.
3. Using lifting equipment and link brackets to support the swing gear and bearing while removing bolts.
4. Removing the inner and outer dust seals from the swing gear and bearing.
The document provides instructions for removing the swing gear and bearing from an excavator undercarriage frame. The procedure involves:
1. Removing all grease from the swing gear and bearing and placing it in a suitable container.
2. Marking the swing gear and bearing and frame for reassembly.
3. Using lifting equipment and link brackets to support the swing gear and bearing while removing bolts.
4. Removing the 280 kg swing gear and bearing assembly.
Caterpillar Cat 336D and 336D L Excavator (Prefix M3N) Service Repair Manual ...8foskkdjdkdm3e
This document provides instructions for assembling and installing the swing drive on excavator models 336D and 336D L. It outlines 29 steps for assembling components like bearings, gears, and housings. It also describes using tools and lifting devices to carefully install the heavy swing drive assembly and tightening bolts to the specified torque. Proper cleaning and application of sealants is emphasized throughout.
Caterpillar Cat 336D and 336D L Excavator (Prefix M3N) Service Repair Manual ...fucheng89
This document provides instructions for removing the swing gear and bearing from an excavator undercarriage frame. The procedure involves removing all grease, marking the swing gear and bearing and frame for alignment, attaching lifting tools, and using a hydraulic torque wrench to remove bolts and spacers. The swing gear and bearing assembly weighs approximately 280 kg and must be lifted carefully after the bolts are removed.
The document provides instructions for removing the swing gear and bearing from an excavator undercarriage frame. The procedure involves:
1. Removing all grease from the swing gear and bearing and placing it in a suitable container.
2. Marking the swing gear and bearing and frame for reassembly.
3. Using lifting equipment and link brackets to support the swing gear and bearing while removing bolts.
4. Removing the 280 kg swing gear and bearing assembly.
Caterpillar Cat 330D L Excavator (Prefix EDX) Service Repair Manual (EDX00001...shudun96087
The document provides instructions for removing the swing gear and bearing from an excavator undercarriage frame. The procedure involves:
1. Removing all grease from the swing gear and bearing and placing it in a suitable container.
2. Marking the swing gear and bearing and frame for reassembly.
3. Using lifting equipment and link brackets to support the swing gear and bearing while removing bolts.
4. Removing the 280 kg swing gear and bearing assembly.
Caterpillar Cat 330D L Excavator (Prefix EDX) Service Repair Manual (EDX00001...kesi7153062
The document provides installation instructions for assembling the swing drive of an excavator. It involves 30 steps including installing bearings and seals into the drive shaft assembly, installing gears and carriers, applying sealant and installing the ring gear and housing cover. Special tools and precautions are noted regarding cleanliness and bearing temperatures. Proper torque values and tightening procedures are specified for reinstalling the completed swing drive assembly into the excavator frame.
The document provides instructions for removing the swing gear and bearing from an excavator undercarriage frame. The procedure involves:
1. Removing all grease from the swing gear and bearing and placing it in a suitable container.
2. Marking the swing gear and bearing and frame for reassembly.
3. Using lifting equipment and link brackets to support the swing gear and bearing while removing bolts.
4. Removing the 280 kg swing gear and bearing assembly.
Caterpillar Cat 330D L Excavator (Prefix EDX) Service Repair Manual (EDX00001...cnp692569
The document provides instructions for removing the swing gear and bearing from an excavator undercarriage frame. The procedure involves:
1. Removing all grease from the swing gear and bearing.
2. Marking the swing gear and bearing and frame for reassembly.
3. Using lifting equipment and link brackets to support the swing gear and bearing while removing bolts.
4. Removing the inner and outer dust seals from the swing gear and bearing.
The document provides instructions for removing the swing gear and bearing from an excavator undercarriage frame. The procedure involves:
1. Removing all grease from the swing gear and bearing and placing it in a suitable container.
2. Marking the swing gear and bearing and frame for reassembly.
3. Using lifting equipment and link brackets to support the swing gear and bearing while removing bolts.
4. Removing the 280 kg swing gear and bearing assembly.
Caterpillar Cat 336D and 336D L Excavator (Prefix M3N) Service Repair Manual ...8foskkdjdkdm3e
This document provides instructions for assembling and installing the swing drive on excavator models 336D and 336D L. It outlines 29 steps for assembling components like bearings, gears, and housings. It also describes using tools and lifting devices to carefully install the heavy swing drive assembly and tightening bolts to the specified torque. Proper cleaning and application of sealants is emphasized throughout.
Caterpillar Cat 336D and 336D L Excavator (Prefix M3N) Service Repair Manual ...fucheng89
This document provides instructions for removing the swing gear and bearing from an excavator undercarriage frame. The procedure involves removing all grease, marking the swing gear and bearing and frame for alignment, attaching lifting tools, and using a hydraulic torque wrench to remove bolts and spacers. The swing gear and bearing assembly weighs approximately 280 kg and must be lifted carefully after the bolts are removed.
This document provides instructions for servicing components of a Caterpillar 330D L excavator engine. It describes procedures for removing and installing the cylinder head, camshaft, lifter group, and associated parts. The steps include draining coolant, removing mounting hardware, lifting components with tools, applying lubricant, and torquing fasteners to specified values. Safety notices are provided to keep parts clean and prevent damage during removal and installation.
Caterpillar Cat 330C L Excavator (Prefix MCA) Service Repair Manual (MCA00001...fjkdksmmdm
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavator models. The disassembly process involves removing 28 different components in a specific sequence. The assembly process reverses the disassembly steps and includes applying thread lock compound and lubricating components before reassembly. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar Cat 330C L Excavator (Prefix KDD) Service Repair Manual (KDD00001...fjkdksmmdm
This document provides instructions for disassembling and assembling a 330C excavator travel motor. It describes 28 steps to disassemble the motor by removing components like the head, port plate, springs, brake piston, plates, and bearings. It then describes 13 steps for assembly, including installing seals, bearings, springs, cam plate, and rotating assembly into the housing. Special tools are listed and safety notices are provided throughout regarding cleaning, pressurized air, and spring loading.
Caterpillar Cat 330C L Excavator (Prefix JNK) Service Repair Manual (JNK00001...fjkdksmmdm
The document provides instructions for assembling and installing a piston motor (hydraulic fan). It is a 3 page document that details 20 steps for assembly, including installing various components like bearings, seals, springs and retaining rings. It then provides 11 steps for installing the assembled piston motor and attaching hoses and guards. Proper cleaning and lubrication of parts is emphasized.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B1K) Service Repair Manual (B1K0000...fjkdksmmdm
This document provides instructions for installing a camshaft on a Caterpillar 330C FM excavator engine. It begins by listing the required tools. The instructions then state to clean all parts, set the number 1 piston to top center, and align the camshaft and idler gears. The camshaft is then lubricated and inserted into the cylinder block. The thrust plate and bolts are installed and tightened. Lifters are repositioned and the procedure ends by installing the front cover and rocker arm assembly.
Caterpillar Cat 330C L Excavator (Prefix JCD) Service Repair Manual (JCD00001...fjkdksmmdm
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavators. It outlines 28 steps for disassembly, removing components like the head, springs, brake piston, and bearings. It then outlines 13 steps for assembly, replacing seals and installing components in the reverse order of disassembly, taking care to mark parts and return them to their original positions. Special tools are listed that may be required for tasks like removing races and seals.
This document provides instructions for disassembling and assembling the travel motor on a 330C excavator. It describes 28 steps to disassemble the motor by removing components like the head, port plate, springs, brake piston, plates, and seals. It then describes 15 steps for reassembling the motor and installing components in the reverse order, making sure to clean parts and apply thread lock compound as needed. Tools required include retaining ring pliers, a bearing puller, an eyebolt, and an adapter.
Caterpillar Cat 330C L Excavator (Prefix GKX) Service Repair Manual (GKX00001...fjkdksmmdm
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of 330C and 330C L excavator models.
2) It details 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components. Special tools are required.
3) It then lists 28 steps for reassembly, providing notes on cleaning, lubrication, and proper installation of O-rings and other parts to ensure correct assembly. The keys and notches must be properly aligned and torques applied to specifications.
Caterpillar Cat 330C L Excavator (Prefix DKY) Service Repair Manual (DKY00001...fjkdksmmdm
- The document provides disassembly and assembly instructions for the travel motor of a 330C L excavator.
- It describes 28 steps to disassemble the travel motor by removing components like the head, plates, seals, and bearing races.
- It then describes 28 steps for assembling the travel motor, providing notes on cleaning, applying sealant, and ensuring proper alignment of components like the cam plate and keys.
- Tools required include retaining ring pliers, a bearing puller, threaded rod, and eyebolt for installation and removal of components.
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavator models. It describes 28 steps to disassemble the motor by removing components like the head, port plate, springs, brake piston, plates, and bearings. It then describes 13 steps for assembly, including installing seals, bearings, springs, and securing the rotating assembly back into the housing. Special tools are listed and safety notices are provided throughout regarding handling pressurized components and ensuring cleanliness during reassembly.
Caterpillar Cat 330C L Excavator (Prefix CYA) Service Repair Manual (CYA00001...fjkdksmmdm
This document provides instructions for disassembling and assembling the travel motor on a 330C L excavator. The disassembly process involves removing 28 components including the head, port plate, springs, brake piston, plates, and seals. The assembly process reverses the disassembly steps and includes installing seals, bearings, and retaining rings in their proper positions. Cleanliness is important during assembly to prevent contamination.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B3M) Service Repair Manual (B3M0000...fjkdksmmdm
This document provides instructions for releasing hydraulic pressure from the systems of a 330C FM excavator before performing service. It describes:
- Releasing pressure from a single circuit by moving the relevant control to its full stroke position with the engine on and activation lever unlocked.
- Releasing pressure from multiple circuits by repeating this process for each circuit needing service.
- Additional steps like starting the engine briefly with no control movement to further release pressure across systems.
The document aims to safely depressurize hydraulic lines and components before disconnection or removal during maintenance.
This document provides instructions for disassembling and assembling the travel motor on a 330C excavator. It describes 28 steps to disassemble the motor by removing components like the head, port plate, bearings, brake piston, plates, and seals. It then describes 13 steps for assembling the motor, replacing all seals and installing components in reverse order of removal. Special tools are required and cleanliness is important when handling parts.
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavator models. The summary is:
1. The travel motor disassembly procedure involves removing 28 components including the head, port plate, springs, brake piston, plates, and seals.
2. Travel motor assembly requires installing components in reverse order, applying thread lock compound and oil, and torquing bolts to specified values.
3. Special tools are required to remove races, seals, and retainers, and care must be taken to avoid damaging parts and ensure proper alignment of keys and plates.
This document provides instructions for assembling a piston motor (hydraulic fan) with 20 steps. It involves installing various components like bearing cups, seals, pins, springs, pistons, and plates in the proper sequence and orientation. Safety notes are included to handle parts carefully and apply oil during assembly. The summary is complete in 3 sentences.
1) The document provides disassembly and assembly instructions for a travel motor on 330C and 330C L excavator models.
2) It describes 28 steps to disassemble the travel motor by removing components like the head, plates, seals, bearings, and housing covers.
3) It then lists 28 steps for reassembling the travel motor, replacing all seals and applying lubricant before reinstalling the components in reverse order of disassembly. Proper cleanliness and torque specifications are emphasized.
1) The document provides instructions for disassembling and assembling the travel motor of a 330C excavator.
2) It describes 28 steps to disassemble the travel motor by removing components like the head, port plate, springs, brake piston, plates, and seals.
3) It then lists 28 steps for reassembling the travel motor, placing components back in reverse order and noting alignment and torque specifications. Precise reassembly is emphasized for correct operation.
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of 330C and 330C L excavator models.
2) It details 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components. Special tools are required.
3) It then lists 28 steps for reassembly, providing notes on cleaning, lubrication, and proper installation of O-rings and other parts to ensure correct assembly. The keys and notches must be properly aligned and torques applied to specifications.
1) The document provides disassembly and assembly instructions for the travel motor of a 330C excavator.
2) It describes 28 steps to disassemble the travel motor by removing components like the head, springs, plates, and seals.
3) It then describes 29 steps for assembling the travel motor, including installing seals, plates, springs, and tightening bolts in the proper order and with specified torques.
Caterpillar Cat 330B L EXCAVATOR (Prefix 8SR) Service Repair Manual (8SR00001...fjkdksmmdm
The document provides instructions for disassembling and assembling various components of an excavator engine, including the compression brake, rocker shaft, and pushrods. The procedures describe removing parts like bolts, wires, pistons, springs and O-rings. Assembly is the reverse of disassembly, and involves installing these components back onto the engine in the proper order and orientation while ensuring parts are clean. Precautions are given to contain fluids and avoid contaminants that could cause wear.
This document provides instructions for servicing components of a Caterpillar 330D L excavator engine. It describes procedures for removing and installing the cylinder head, camshaft, lifter group, and associated parts. The steps include draining coolant, removing mounting hardware, lifting components with tools, applying lubricant, and torquing fasteners to specified values. Safety notices are provided to keep parts clean and prevent damage during removal and installation.
Caterpillar Cat 330C L Excavator (Prefix MCA) Service Repair Manual (MCA00001...fjkdksmmdm
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavator models. The disassembly process involves removing 28 different components in a specific sequence. The assembly process reverses the disassembly steps and includes applying thread lock compound and lubricating components before reassembly. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar Cat 330C L Excavator (Prefix KDD) Service Repair Manual (KDD00001...fjkdksmmdm
This document provides instructions for disassembling and assembling a 330C excavator travel motor. It describes 28 steps to disassemble the motor by removing components like the head, port plate, springs, brake piston, plates, and bearings. It then describes 13 steps for assembly, including installing seals, bearings, springs, cam plate, and rotating assembly into the housing. Special tools are listed and safety notices are provided throughout regarding cleaning, pressurized air, and spring loading.
Caterpillar Cat 330C L Excavator (Prefix JNK) Service Repair Manual (JNK00001...fjkdksmmdm
The document provides instructions for assembling and installing a piston motor (hydraulic fan). It is a 3 page document that details 20 steps for assembly, including installing various components like bearings, seals, springs and retaining rings. It then provides 11 steps for installing the assembled piston motor and attaching hoses and guards. Proper cleaning and lubrication of parts is emphasized.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B1K) Service Repair Manual (B1K0000...fjkdksmmdm
This document provides instructions for installing a camshaft on a Caterpillar 330C FM excavator engine. It begins by listing the required tools. The instructions then state to clean all parts, set the number 1 piston to top center, and align the camshaft and idler gears. The camshaft is then lubricated and inserted into the cylinder block. The thrust plate and bolts are installed and tightened. Lifters are repositioned and the procedure ends by installing the front cover and rocker arm assembly.
Caterpillar Cat 330C L Excavator (Prefix JCD) Service Repair Manual (JCD00001...fjkdksmmdm
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavators. It outlines 28 steps for disassembly, removing components like the head, springs, brake piston, and bearings. It then outlines 13 steps for assembly, replacing seals and installing components in the reverse order of disassembly, taking care to mark parts and return them to their original positions. Special tools are listed that may be required for tasks like removing races and seals.
This document provides instructions for disassembling and assembling the travel motor on a 330C excavator. It describes 28 steps to disassemble the motor by removing components like the head, port plate, springs, brake piston, plates, and seals. It then describes 15 steps for reassembling the motor and installing components in the reverse order, making sure to clean parts and apply thread lock compound as needed. Tools required include retaining ring pliers, a bearing puller, an eyebolt, and an adapter.
Caterpillar Cat 330C L Excavator (Prefix GKX) Service Repair Manual (GKX00001...fjkdksmmdm
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of 330C and 330C L excavator models.
2) It details 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components. Special tools are required.
3) It then lists 28 steps for reassembly, providing notes on cleaning, lubrication, and proper installation of O-rings and other parts to ensure correct assembly. The keys and notches must be properly aligned and torques applied to specifications.
Caterpillar Cat 330C L Excavator (Prefix DKY) Service Repair Manual (DKY00001...fjkdksmmdm
- The document provides disassembly and assembly instructions for the travel motor of a 330C L excavator.
- It describes 28 steps to disassemble the travel motor by removing components like the head, plates, seals, and bearing races.
- It then describes 28 steps for assembling the travel motor, providing notes on cleaning, applying sealant, and ensuring proper alignment of components like the cam plate and keys.
- Tools required include retaining ring pliers, a bearing puller, threaded rod, and eyebolt for installation and removal of components.
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavator models. It describes 28 steps to disassemble the motor by removing components like the head, port plate, springs, brake piston, plates, and bearings. It then describes 13 steps for assembly, including installing seals, bearings, springs, and securing the rotating assembly back into the housing. Special tools are listed and safety notices are provided throughout regarding handling pressurized components and ensuring cleanliness during reassembly.
Caterpillar Cat 330C L Excavator (Prefix CYA) Service Repair Manual (CYA00001...fjkdksmmdm
This document provides instructions for disassembling and assembling the travel motor on a 330C L excavator. The disassembly process involves removing 28 components including the head, port plate, springs, brake piston, plates, and seals. The assembly process reverses the disassembly steps and includes installing seals, bearings, and retaining rings in their proper positions. Cleanliness is important during assembly to prevent contamination.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B3M) Service Repair Manual (B3M0000...fjkdksmmdm
This document provides instructions for releasing hydraulic pressure from the systems of a 330C FM excavator before performing service. It describes:
- Releasing pressure from a single circuit by moving the relevant control to its full stroke position with the engine on and activation lever unlocked.
- Releasing pressure from multiple circuits by repeating this process for each circuit needing service.
- Additional steps like starting the engine briefly with no control movement to further release pressure across systems.
The document aims to safely depressurize hydraulic lines and components before disconnection or removal during maintenance.
This document provides instructions for disassembling and assembling the travel motor on a 330C excavator. It describes 28 steps to disassemble the motor by removing components like the head, port plate, bearings, brake piston, plates, and seals. It then describes 13 steps for assembling the motor, replacing all seals and installing components in reverse order of removal. Special tools are required and cleanliness is important when handling parts.
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavator models. The summary is:
1. The travel motor disassembly procedure involves removing 28 components including the head, port plate, springs, brake piston, plates, and seals.
2. Travel motor assembly requires installing components in reverse order, applying thread lock compound and oil, and torquing bolts to specified values.
3. Special tools are required to remove races, seals, and retainers, and care must be taken to avoid damaging parts and ensure proper alignment of keys and plates.
This document provides instructions for assembling a piston motor (hydraulic fan) with 20 steps. It involves installing various components like bearing cups, seals, pins, springs, pistons, and plates in the proper sequence and orientation. Safety notes are included to handle parts carefully and apply oil during assembly. The summary is complete in 3 sentences.
1) The document provides disassembly and assembly instructions for a travel motor on 330C and 330C L excavator models.
2) It describes 28 steps to disassemble the travel motor by removing components like the head, plates, seals, bearings, and housing covers.
3) It then lists 28 steps for reassembling the travel motor, replacing all seals and applying lubricant before reinstalling the components in reverse order of disassembly. Proper cleanliness and torque specifications are emphasized.
1) The document provides instructions for disassembling and assembling the travel motor of a 330C excavator.
2) It describes 28 steps to disassemble the travel motor by removing components like the head, port plate, springs, brake piston, plates, and seals.
3) It then lists 28 steps for reassembling the travel motor, placing components back in reverse order and noting alignment and torque specifications. Precise reassembly is emphasized for correct operation.
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of 330C and 330C L excavator models.
2) It details 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components. Special tools are required.
3) It then lists 28 steps for reassembly, providing notes on cleaning, lubrication, and proper installation of O-rings and other parts to ensure correct assembly. The keys and notches must be properly aligned and torques applied to specifications.
1) The document provides disassembly and assembly instructions for the travel motor of a 330C excavator.
2) It describes 28 steps to disassemble the travel motor by removing components like the head, springs, plates, and seals.
3) It then describes 29 steps for assembling the travel motor, including installing seals, plates, springs, and tightening bolts in the proper order and with specified torques.
Caterpillar Cat 330B L EXCAVATOR (Prefix 8SR) Service Repair Manual (8SR00001...fjkdksmmdm
The document provides instructions for disassembling and assembling various components of an excavator engine, including the compression brake, rocker shaft, and pushrods. The procedures describe removing parts like bolts, wires, pistons, springs and O-rings. Assembly is the reverse of disassembly, and involves installing these components back onto the engine in the proper order and orientation while ensuring parts are clean. Precautions are given to contain fluids and avoid contaminants that could cause wear.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330D L EXCAVATOR EDX
Configuration: 330D & 330D L Excavators EDX00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i06939513
Swing Drive - Assemble
SMCS - 5459-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-5197 Pliers 1
B 138-7574 Link Brackets 2
C 138-7575 Link Bracket 3
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
1/10(W)
w
2020/8/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Illustration 1 g00869899
1. Install lip seals (32) and O-ring seal (33) in bearing cage (29).
Illustration 2 g00870134
Note: Lubricate the seals and the seal surface of the shaft before you install the cage
assembly.
2. Carefully install cage (29) on shaft (31).
Illustration 3 g00870142
3. Raise the temperature of bearing (36) to 135 °C (275 °F) and use two people to install the
bearing on shaft (31). The weight of bearing (36) is approximately 35 kg (77 lb).
4. Install spacer (35) on shaft assembly (31). Install the spacer with relief against bearing (36).
2/10(W)
w
2020/8/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. Illustration 4 g00870160
5. Raise the temperature of bearing (34) to 135 °C (275 °F). Install the bearing on shaft (31)
and against spacer (35).
Illustration 5 g00870169
6. Use Tooling (A) to install retaining ring (28) on shaft (31) and against bearing (34).
Illustration 6 g01041406
7. Install shaft assembly (31) in swing drive housing (16).
3/10(W)
w
2020/8/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. a. Apply 5P-3931 Anti-Seize Compound on the inside diameter of swing drive housing
(16).
b. Lower the temperature of shaft assembly (31).
c. Attach Tooling (C) and a suitable lifting device to the shaft assembly.
d. Install the shaft assembly into swing drive housing (16). Bearing (34) must be within
the bore of the swing drive housing.
e. Remove Tooling (C) and the suitable lifting device from the shaft assembly. Attach
Tooling (C) and the suitable lifting device to the swing drive housing.
f. Lift the swing drive vertically. Use a hammer and a drift to align bearing (34) in the
lower bore of the swing drive housing. When the bearing is properly aligned in the
bore, shaft assembly (31) will drop into the proper position within the swing drive
housing.
Illustration 7 g00870264
8. Apply 1U-8846 Sealant on the threads of bolts (30).
9. Install bolts (30) and washers in bearing cage (29) and swing drive housing (16).
Illustration 8 g00869483
4/10(W)
w
2020/8/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Illustration 9 g00870281
10. Install bearings (24) and (26) in gear (25).
11. Install gear (25) and washers (23) and (27) in carrier (20).
12. Lower the temperature of shaft (22). Install the shaft in carrier assembly (20).
13. Install pin (21) in the carrier assembly and the shaft.
14. Use a hammer and a center punch to stake the pin in the carrier housing.
15. Repeat Steps 10 through Steps 14 on the remaining gear assemblies.
Illustration 10 g00869464
16. Use a suitable lifting device to install carrier assembly (20). The weight of carrier assembly
(20) is approximately 68 kg (150 lb).
5/10(W)
w
2020/8/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Illustration 11 g00869460
17. Install retaining ring (19).
Illustration 12 g00869406
18. Install spacer (17) in carrier assembly (18).
Illustration 13 g00869390
19. Make sure that the mating surfaces of ring gear (15) and swing drive housing (16) are
thoroughly clean.
6/10(W)
w
2020/8/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. 20. Apply 1U-8846 Gasket Sealant to the face of swing drive housing (16) and the face of ring
gear (15).
21. Use Tooling (B) and a suitable lifting device to install ring gear (15) in swing drive housing
(16). The weight of ring gear (15) is approximately 80 kg (175 lb).
Illustration 14 g00869383
22. Install retaining ring (14) into the sun gear.
Illustration 15 g00869377
23. Install sun gear (13) in carrier assembly (4). Install upper retaining ring (12).
24. Assemble carrier assembly (4).
7/10(W)
w
2020/8/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Illustration 16 g00869315
a. Apply clean SAE 30W oil on bearing (10). Install bearing (10) in planetary gear (9).
b. Install thrust washer (8) on one side of planetary gear (9).
c. Install thrust washer (11) on the other side of planetary gear (9).
d. Use a deburring tool to remove the metal burr from the openings in the carrier.
e. Install planetary gear (9) and the thrust washers in carrier assembly (4).
Illustration 17 g00869309
f. Install planetary shaft (7) through the gear assembly into the carrier assembly. Make
sure that the spring pin hole in the planetary shaft is in alignment with the spring pin
hole in the carrier.
Illustration 18 g00703700
8/10(W)
w
2020/8/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. g. Drive spring pin (6) into shaft (7). Orient the split in spring pin (6) vertically to the
carrier. Align the split in the spring pin to the top or the bottom. Make a stake mark
on each side of the spring pin hole in the carrier. Each stake mark should be
approximately 2.25 ± 0.75 mm (0.09 ± 0.03 inch) from the outside diameter of the
spring pin hole.
h. Repeat Steps 24.a through 24.g to install the other three planetary gears in the carrier.
Illustration 19 g00869294
25. Use two people to install carrier assembly (4) in the ring gear. The weight of the carrier
assembly is approximately 36 kg (80 lb).
26. Install spacer (5) in carrier assembly (4).
Illustration 20 g00869281
27. Install sun gear (3) in carrier assembly (4).
9/10(W)
w
2020/8/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Illustration 21 g00869266
28. Make sure that the mating surfaces of the ring gear and cover (2) are thoroughly clean.
29. Apply 1U-8846 Gasket Sealant on the flange surface of the ring gear and cover (5).
30. Install cover (2) and bolts (1).
End By:
a. Install the swing drive. Refer to Disassembly and Assembly, "Swing Drive - Remove and
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Aug 19 12:34:27 UTC+0800 2020
10/10(W)
w
2020/8/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330D L EXCAVATOR EDX
Configuration: 330D & 330D L Excavators EDX00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i07192381
Swing Drive - Install
SMCS - 5459-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
132-8223 110 volt Power Pack 1
1U-6221 Torque Wrench 1
132-8143 36 mm Hex Link 1
B 439-3939 Link Bracket As 4
C -
Forcing Bolt
M24 x 3 by 5 inch
2
D - Loctite C5A Copper Anti-Seize -
E 1U-8846 Gasket Sealant 1
1. Apply Tooling (D) on the locating pin and the pin bore in the main frame. Apply Tooling
(E) on the mating surface of the main frame and the swing drive housing.
1/3(W)
w
2020/8/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Illustration 1 g00875735
2. Attach Tooling (B) and a suitable lifting device to swing drive (2), as shown. The weight of
swing drive (2) is approximately 510 kg (1125 lb). Install swing drive (2) into the original
position. Be careful not to damage the pinion gear.
Note: During installation, the locating pin for the swing drive can come out of the swing
drive housing. The locating pin can be installed with a hammer after the swing drive is in
place.
Illustration 2 g01206242
3. Use Tooling (A) to install bolts (1) that secure the swing drive to the main frame.
4. Before assembly, remove compound, oil, and dust from female threads, then apply Tooling
(D) to the threads of bolts (1).
5. Tighten bolts (1) in an alternating sequence to a torque of 250 ± 25 N·m (184 ± 18 lb ft).
Turn an additional angle of 45 ± 5 degrees. Refer to Service Magazine , M0083843 , "An
Improved Bolt Tightening Procedure for the Critical Joints Is Now Used on all Excavators"
for more detailed information.
6. Fill the swing drive with oil. Refer to Operation and Maintenance Manual, "Swing Drive Oil
- Change".
End By:
2/3(W)
w
2020/8/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. a. Install the swing motor. Refer to Disassembly and Assembly, "Swing Motor - Install"
.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Aug 19 12:35:29 UTC+0800 2020
3/3(W)
w
2020/8/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330D L EXCAVATOR EDX
Configuration: 330D & 330D L Excavators EDX00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02386587
Swing Gear and Bearing - Remove
SMCS - 7063-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7576 Link Bracket 4
B
132-8223 Hydraulic Pump and Motor (115 V 50/60 Hz Single Phase)(1)
1
1U-6221 Hydraulic Torque Wrench 1
132-8143 36 mm Hex Link 1
(1)
132-8231 Hydraulic Pump and Motor (220 V 50/60 Hz Single Phase) is also available.
Start By:
a. Remove the undercarriage frame. Refer to Disassembly and Assembly, "Upper Frame and
Undercarriage Frame - Separate".
1. Remove all of the grease from the swing gear and bearing. Put the grease in a suitable
container for storage or disposal.
1/3(W)
w
2020/8/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Illustration 1 g00520664
2. Put an alignment mark on swing gear and bearing (1) and on the undercarriage frame
assembly for assembly purposes. Attach Tooling (A) and a suitable lifting device to swing
gear and bearing (1), as shown. Apply slight lifting tension to the swing gear and bearing.
Illustration 2 g00520670
3. Use Tooling (B) in order to remove bolts (2) and the spacers that hold swing gear and
bearing (1) to the undercarriage frame.
4. Remove swing gear and bearing (1). The weight of the swing gear and bearing (1) is
approximately 280 kg (615 lb).
2/3(W)
w
2020/8/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Illustration 3 g00721855
Note: Inner dust seal (3) and outer dust seal (4) may have been installed dry in the swing
gear and bearing or inner dust seal (3) and outer dust seal (4) may have been bonded to the
swing gear and bearing.
5. Remove inner dust seal (3) and outer dust seal (4) from the swing gear and bearing.
6. Clean the seal grooves of the inner dust seal and the outer dust seal with a fine grit
sandpaper. Use a cleaning solvent to clean the sealing grooves. Make sure that the seal
grooves are thoroughly clean and dry prior to installing the new dust seals.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Aug 19 12:36:32 UTC+0800 2020
3/3(W)
w
2020/8/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330D L EXCAVATOR EDX
Configuration: 330D & 330D L Excavators EDX00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic Power
Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i07191587
Swing Gear and Bearing - Install
SMCS - 7063-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 439-3941 Link Bracket As 4
B
132-8223 Hydraulic Pump and Motor (115 V 50/60 Hz Single Phase)(1)
1
1U-6221 Hydraulic Torque Wrench 1
132-8143 36 mm Hex Link 1
C - Loctite 435 -
D 2P-9066 Lubricant 1
E 1U-8846 Gasket Sealant 1
F - Loctite C5A Copper Anti-Seize -
(1)
132-8231 Hydraulic Pump and Motor (220 V 50/60 Hz Single Phase) is also available.
Note: If the inner dust seal (3) and the outer dust seal (4) are installed dry, the new dust seals should
be installed dry in the swing gear and bearing.
Note: If the inner dust seal and the outer dust seal are bonded to the swing gear and bearing, the new
dust seals should be bonded to the swing gear and bearing.
Note: Perform Steps 1.a through 1.j to install the new dry dust seals.
Note: Perform Steps 2.a through 2.p to install the new dust seals that are bonded to the swing gear
and bearing.
1/6(W)
w
2020/8/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Illustration 1 g00636223
1. If inner dust seal (3) and outer dust seal (4) were installed dry, use the following procedure to install
the new dust seals:
a. Use a wire brush to thoroughly clean the grooves for the dust seal of the swing gear and
bearing. Make sure that all the dirt and foreign material has been removed.
b. Wash the grooves for the dust seal in a suitable solvent that will not leave an oily residue.
c. Make sure that the grooves for the dust seal in the swing gear and bearing are thoroughly clean
and dry prior to installation of the dust seals.
d. Cut one end of inner dust seal (3) at a 90 degree angle. Use a blunt tool to install the inner dust
seal in the seal groove of the swing gear and bearing.
e. Install the seal so that the lip of the seal is facing in the direction that is shown. Refer to
Illustration 1.
f. After the inner dust seal is installed in the seal groove, measure the seal and cut the remaining
end of the inner dust seal at a 90 degree angle. Install the remaining end of the inner dust seal
in the seal groove.
g. Make sure that the inner dust seal is seated properly in the seal groove, all the way around the
swing gear and bearing. Also, make sure that there is no gap between the ends of the inner dust
seal.
h. Pull each end of the inner dust seal out of the seal groove of the swing gear and bearing
approximately 50.8 mm (2.00 inch). Apply Tooling (C) to each end of the inner dust seal to
bond the seals together.
i. Immediately reinstall the inner dust seal in the seal groove of the swing gear and bearing.
Again, make sure that the entire inner dust seal is properly seated in the seal groove of the
swing gear and bearing. No gap should exist between the ends of the inner dust seal.
j. To ensure that the lip of inner dust seal has not adhered to the top of the bearing at the seal
joint, run a dull putty knife between the lip of the seal and the bearing at the seal joint.
k. Follow the procedure in Steps 1.a through 1.j to install outer dust seal (4) in the swing gear and
bearing. Refer to Illustration 1 for proper seal orientation in the swing gear and bearing.
2/6(W)
w
2020/8/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. 2. If inner dust seal (3) and outer dust seal (4) were bonded in the swing gear and bearing, use the
following procedure to install the new dust seals:
a. Thoroughly clean all the dirt and foreign material from the grooves for the dust seal in the
swing gear and bearing with a wire brush.
b. Wash the grooves for the dust seal in a suitable solvent that will not leave an oily residue.
c. Make sure that the grooves for the dust seals in the swing gear and bearing are thoroughly
clean and dry prior to installation of the dust seals.
Note: Install inner dust seal (3) and outer dust seal (4) in the swing gear and bearing in small
increments, because Tooling (C) cures very quickly.
d. Cut one end of inner dust seal (3) at a 90 degree angle.
e. Start applying Tooling (C) 50.8 mm (2.00 inch) from the cut end of the seal. Apply Tooling
(C) to the seal in 152.4 mm (6.00 inch) increments.
f. Immediately use a blunt tool to install only the bonded portion of the inner dust seal in the seal
groove of the swing gear and bearing. Make sure that the dust seal is seated properly in the
seal groove.
g. Install the seal so that the lip of the seal is facing in the direction that is shown. Refer to
Illustration 1.
h. To ensure that the inner dust seal has not adhered to the bearing, run a dull putty knife between
the lip of the seal and the bearing.
i. Apply Tooling (C) to the next 152.4 mm (6.00 inch) of the seal. Immediately use a blunt tool
to install only the bonded portion of the inner dust seal in the seal groove of the swing gear and
bearing.
j. Make sure that the inner dust seal is seated properly in the seal groove. Ensure that the inner
dust seal has not adhered to the bearing.
Note: Do not install the last 152.4 mm (6.00 inch) of the inner dust seal.
k. Repeat Steps 2.i through 2.j until the dust seal is installed.
l. Measure the inner dust seal and cut the remaining end of inner dust seal (3) at a 90 degree
angle. Install the last 152.4 mm (6.00 inch) of seal in the seal groove dry.
m. Make sure that the inner dust seal is properly seated in the seal groove and that there is no gap
between the seal ends. Carefully remove both loose ends of the inner dust seal out of the seal
groove.
n. Apply Tooling (C) to the loose ends of the seal.
o. Immediately use a blunt tool to reinstall the seal ends in the seal groove. Again, make sure that
the inner dust seal is properly seated in the seal groove, and that no gap existed between the
ends of the seal.
p. To ensure that the inner dust seal has not adhered to the top of the bearing, run a dull putty
knife around the seal.
q. Follow the procedure in Steps 2.a through 2.p to install outer dust seal (4) in the swing gear
and bearing. Refer to Illustration 1 for proper seal orientation in the swing gear and bearing.
3. Lubricate the swing gear and bearing with grease.
3/6(W)
w
2020/8/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Illustration 2 g00520664
Illustration 3 g00520674
Note: Clean the mating surface for the swing gear and bearing on the undercarriage frame assembly.
4. Apply Tooling (E) on the mating surface for the swing gear and bearing of the undercarriage frame
assembly.
5. Fasten Tooling (A) and a suitable lifting device to swing gear and bearing (1), as shown. Refer to
Illustration 2. The weight of swing gear and bearing (1) is approximately 660 kg (1455 lb).
6. Place the swing gear and bearing in the swing gear and bearing's original position on the
undercarriage frame assembly.
7. Make sure that the stamp "S" on the inner race is in the position that is shown, relative to the
undercarriage frame assembly and the stopper on the outer race. Refer to Illustration 3.
4/6(W)
w
2020/8/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Illustration 4 g00520670
8. Apply a thin coat of Tooling (F) on the threads of bolts (2). Install the spacers and bolts (2) that
secure the swing gear and bearing to the undercarriage frame assembly.
Note: Some machines use bolts that are plated with Dacromet. Dacromet bolts appear silver, gray in
color. Do not apply Tooling (F) to the threads of Dacromet bolts. Make sure that the bolt holes are
clean and dry when Dacromet bolts are used.
Note: Torque for bolts (2) is 1000 ± 125 N·m (738 ± 92 lb ft) on 345 excavators.
Note: Torque for bolts (2) is 250 ± 25 N·m (184 ± 18 lb ft) and turn an additional angle of 55 ± 5
degrees on 336 excavators.
9. Use Tooling (B) to tighten bolts (2) to a torque of 900 ± 100 N·m (665 ± 75 lb ft).
10. Refer to Service Magazine , M0083843 , "An Improved Bolt Tightening Procedure for the Critical
Joints Is Now Used on all Excavators" for more detailed information.
NOTICE
Improper lubrication can cause damage to machine components.
To avoid damage, make sure that the proper amount of grease is
applied to the swing drive.
When the amount of grease in the compartment becomes too large, the
agitation loss becomes large, thereby accelerating grease deterioration.
Grease deterioration can cause damage to the pinion gear of the swing
drive and swing internal gear.
Not enough grease will result in poor gear lubrication.
11. Add Tooling (D) to the swing gear and bearing after the installation.
Reference: Refer to Operation and Maintenance Manual, "Refill Capacities" for the capacity of the
swing gear and bearing.
Reference: Refer to Operation and Maintenance Manual, "Swing Gear - Lubricate" for lubricating
the swing gear and bearing.
5/6(W)
w
2020/8/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. Reference: Refer to Operation and Maintenance Manual, "Maintenance Interval Schedule" for the
schedule for lubricating the swing gear and bearing.
End By:
a. Install the undercarriage frame assembly. Refer to Disassembly and Assembly, "Undercarriage
Frame - Install" in this manual.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Aug 19 12:37:35 UTC+0800 2020
6/6(W)
w
2020/8/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330D L EXCAVATOR EDX
Configuration: 330D & 330D L Excavators EDX00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02451315
Oil Filter (Hydraulic, Return) - Remove
SMCS - 5068-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
Start By:
a. Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic
System Pressure - Release".
1. Drain the hydraulic oil into a suitable container for storage or disposal. Refer to Operation
and Maintenance Manual, "Hydraulic Oil - Change".
Illustration 1 g01218778
1/3(W)
w
2020/8/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
26. 2. Remove bolts (1) and reposition filter assembly (2).
Illustration 2 g01218865
3. Disconnect hose assemblies (4). Remove bolts (3). Reposition filter assembly (5) out of the
way.
Illustration 3 g01223795
4. Remove bolts (6) from pipe assembly (7).
Illustration 4 g01218952
2/3(W)
w
2020/8/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...