This document provides instructions for removing and installing various engine components on Caterpillar 320C excavators, including the flywheel, crankshaft rear seal, flywheel housing, crankshaft pulley, and crankshaft front seal. The procedures describe using various tools to remove and install each part, providing illustrations to supplement the text instructions. Safety notices are included to handle parts carefully and contain fluids.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for removing and installing a crankshaft pulley on Caterpillar 320C excavator models. The removal procedure involves using a combination puller tool to remove the nut and washer from the crankshaft, then using a puller tool to remove the pulley. The installation procedure specifies cleaning the crankshaft, placing the pulley in position, and securing it with a washer and nut tightened to the specified torque. Proper cleaning and installation of seals is also addressed.
This document provides instructions for removing and installing a crankshaft pulley on Caterpillar 320C excavator models. The removal procedure involves using a combination puller tool to remove the nut and washer from the crankshaft, then using a puller tool to remove the pulley. The installation procedure specifies cleaning the crankshaft, placing the pulley in position, and securing it with a washer and nut tightened to the specified torque. Tools required include a combination puller, socket, and cleaning supplies.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for removing and installing a crankshaft pulley on Caterpillar 320C excavator models. The removal procedure involves using a combination puller tool to remove the nut and washer from the crankshaft, then using a puller tool to remove the pulley. The installation procedure specifies cleaning the crankshaft, placing the pulley in position, and securing it with a washer and nut tightened to the specified torque. Proper cleaning and installation of seals is also addressed.
Caterpillar Cat 320C L Excavator (Prefix DBG) Service Repair Manual (DBG00001...nai93qing
This document provides instructions for removing and installing a crankshaft pulley on Caterpillar 320C excavator models. The removal procedure involves using a combination puller tool to remove the nut and washer from the crankshaft, then using a puller tool to remove the pulley. The installation procedure specifies cleaning the crankshaft, placing the pulley in position, and securing it with a washer and nut tightened to the specified torque. Tools required include a combination puller, socket, and cleaning supplies.
This document provides instructions for removing and installing a crankshaft pulley on Caterpillar 320C excavator models. The removal procedure involves using a combination puller tool to remove the nut and washer from the crankshaft, then using a puller tool to remove the pulley. The installation procedure specifies cleaning the crankshaft, placing the pulley in position, and securing it with a washer and nut tightened to the specified torque. Tools required include a combination puller, socket, and cleaning supplies.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for removing and installing a crankshaft pulley on Caterpillar 320C excavator models. The removal procedure involves using a combination puller tool to remove the nut and washer from the crankshaft, then using a puller tool to remove the pulley. The installation procedure specifies cleaning the crankshaft, placing the pulley in position, and securing it with a washer and nut tightened to the specified torque. Proper cleaning and installation of seals is also addressed.
This document provides instructions for removing and installing a crankshaft pulley on Caterpillar 320C excavator models. The removal procedure involves using a combination puller tool to remove the nut and washer from the crankshaft, then using a puller tool to remove the pulley. The installation procedure specifies cleaning the crankshaft, placing the pulley in position, and securing it with a washer and nut tightened to the specified torque. Tools required include a combination puller, socket, and cleaning supplies.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for removing and installing a crankshaft pulley on Caterpillar 320C excavator models. The removal procedure involves using a combination puller tool to remove the nut and washer from the crankshaft, then using a puller tool to remove the pulley. The installation procedure specifies cleaning the crankshaft, placing the pulley in position, and securing it with a washer and nut tightened to the specified torque. Proper cleaning and installation of seals is also addressed.
Caterpillar Cat 320C L Excavator (Prefix DBG) Service Repair Manual (DBG00001...nai93qing
This document provides instructions for removing and installing a crankshaft pulley on Caterpillar 320C excavator models. The removal procedure involves using a combination puller tool to remove the nut and washer from the crankshaft, then using a puller tool to remove the pulley. The installation procedure specifies cleaning the crankshaft, placing the pulley in position, and securing it with a washer and nut tightened to the specified torque. Tools required include a combination puller, socket, and cleaning supplies.
This document provides instructions for removing and installing a crankshaft pulley on Caterpillar 320C excavator models. The removal procedure involves using a combination puller tool to remove the nut and washer from the crankshaft, then using a puller tool to remove the pulley. The installation procedure specifies cleaning the crankshaft, placing the pulley in position, and securing it with a washer and nut tightened to the specified torque. Tools required include a combination puller, socket, and cleaning supplies.
This document provides instructions for removing and installing a crankshaft pulley on Caterpillar 320C excavator models. The removal procedure involves using a combination puller tool to remove the nut and washer from the crankshaft, then using a puller tool to remove the pulley. The installation procedure specifies cleaning the crankshaft, placing the pulley in position, and securing it with a washer and nut tightened to the specified torque. Proper cleaning and installation of seals is also addressed.
Caterpillar Cat 320C L Excavator (Prefix DBG) Service Repair Manual (DBG00001...fusjekkdmdmd2w
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and crankshaft front seal. The procedures describe using various tools to remove and install each part, providing illustrations to supplement the text instructions. Safety notices are included to keep parts clean and contain fluids properly during the repair work.
This document provides instructions for removing and installing a crankshaft pulley on Caterpillar 320C excavator models. The removal procedure involves using a combination puller tool to remove the nut and washer from the crankshaft, then using a puller tool to remove the pulley. The installation procedure specifies cleaning the crankshaft, placing the pulley in position, and securing it with a washer and nut tightened to the specified torque. Tools required include a combination puller, socket, and cleaning supplies.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
Caterpillar Cat 320C L Excavator (Prefix DBG) Service Repair Manual (DBG00001...zoat27912076
This document provides instructions for removing and installing a crankshaft pulley on Caterpillar 320C excavator models. The removal procedure involves using a combination puller tool to remove the nut and washer from the crankshaft, then using a puller tool to remove the pulley. The installation procedure specifies cleaning the crankshaft, placing the pulley in position, and securing it with a washer and nut tightened to the specified torque. Tools required include a combination puller, socket, and cleaning supplies.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
Caterpillar Cat 320C L Excavator (Prefix DBG) Service Repair Manual (DBG00001...f8skjdkdmdmd
This document provides instructions for removing and installing a crankshaft pulley on Caterpillar 320C excavator models. The removal procedure involves using a combination puller tool to remove the nut and washer from the crankshaft, then using a puller tool to remove the pulley. The installation procedure specifies cleaning the crankshaft, placing the pulley in position, and securing it with a washer and nut tightened to the specified torque. Tools required include a combination puller, socket, and cleaning supplies.
This document provides instructions for removing and installing a crankshaft pulley on Caterpillar 320C excavator models. The removal procedure involves using a combination puller tool to remove the nut and washer from the crankshaft, then using a puller tool to remove the pulley. The installation procedure specifies cleaning the crankshaft, placing the pulley in position, and securing it with a washer and nut tightened to the specified torque. Tools required include a combination puller, socket, and cleaning supplies.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
Caterpillar Cat 320C L Excavator (Prefix DBG) Service Repair Manual (DBG00001...fhjsekdmdm3e
This document provides instructions for removing and installing a crankshaft pulley on Caterpillar 320C excavator models. The removal procedure involves using a combination puller tool to remove the nut and washer from the crankshaft, then using a puller tool to remove the pulley. The installation procedure specifies cleaning the crankshaft, placing the pulley in position, and securing it with a washer and nut tightened to the specified torque. Tools required include a combination puller, socket, and cleaning supplies.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
Caterpillar Cat 320C L Excavator (Prefix DBG) Service Repair Manual (DBG00001...f8usjejkdmmd
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
Caterpillar Cat 320C L Excavator (Prefix DBG) Service Repair Manual (DBG00001...8dusjkdmmdmd
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
Caterpillar Cat 320C L Excavator (Prefix DBG) Service Repair Manual (DBG00001...fujsekkdmmdm
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
Caterpillar Cat 320C U Excavator (Prefix PAC) Service Repair Manual (PAC00001...wenxian17880
This document provides instructions for removing and installing various engine components on a Caterpillar 320C excavator. The instructions covered include:
- Removing and installing the flywheel housing.
- Removing and installing the crankshaft pulley.
- Removing the crankshaft front seal.
- Installing the crankshaft front seal.
- Removing the idler gear from the front gear group.
- Installing the idler gear.
The document provides detailed step-by-step instructions accompanied by illustrations. Safety and cleaning notes are also included.
Caterpillar Cat 320C S 320CS Excavator (Prefix BCN) Service Repair Manual (BC...wenxian17880
This document provides instructions for removing and installing various fuel system components on a 320C excavator model powered by a 3066 engine. The components include the fuel filter base, fuel injection lines, fuel injection nozzles, fuel shutoff solenoid, and fuel injection pump. The procedures describe disconnecting fuel lines, removing mounting hardware, and ensuring openings are plugged to prevent contamination. Special tools may be required and safety precautions are noted.
More Related Content
Similar to Caterpillar Cat 320C LN Excavator (Prefix DBG) Service Repair Manual (DBG00001 and up).pdf
This document provides instructions for removing and installing a crankshaft pulley on Caterpillar 320C excavator models. The removal procedure involves using a combination puller tool to remove the nut and washer from the crankshaft, then using a puller tool to remove the pulley. The installation procedure specifies cleaning the crankshaft, placing the pulley in position, and securing it with a washer and nut tightened to the specified torque. Proper cleaning and installation of seals is also addressed.
Caterpillar Cat 320C L Excavator (Prefix DBG) Service Repair Manual (DBG00001...fusjekkdmdmd2w
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and crankshaft front seal. The procedures describe using various tools to remove and install each part, providing illustrations to supplement the text instructions. Safety notices are included to keep parts clean and contain fluids properly during the repair work.
This document provides instructions for removing and installing a crankshaft pulley on Caterpillar 320C excavator models. The removal procedure involves using a combination puller tool to remove the nut and washer from the crankshaft, then using a puller tool to remove the pulley. The installation procedure specifies cleaning the crankshaft, placing the pulley in position, and securing it with a washer and nut tightened to the specified torque. Tools required include a combination puller, socket, and cleaning supplies.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
Caterpillar Cat 320C L Excavator (Prefix DBG) Service Repair Manual (DBG00001...zoat27912076
This document provides instructions for removing and installing a crankshaft pulley on Caterpillar 320C excavator models. The removal procedure involves using a combination puller tool to remove the nut and washer from the crankshaft, then using a puller tool to remove the pulley. The installation procedure specifies cleaning the crankshaft, placing the pulley in position, and securing it with a washer and nut tightened to the specified torque. Tools required include a combination puller, socket, and cleaning supplies.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
Caterpillar Cat 320C L Excavator (Prefix DBG) Service Repair Manual (DBG00001...f8skjdkdmdmd
This document provides instructions for removing and installing a crankshaft pulley on Caterpillar 320C excavator models. The removal procedure involves using a combination puller tool to remove the nut and washer from the crankshaft, then using a puller tool to remove the pulley. The installation procedure specifies cleaning the crankshaft, placing the pulley in position, and securing it with a washer and nut tightened to the specified torque. Tools required include a combination puller, socket, and cleaning supplies.
This document provides instructions for removing and installing a crankshaft pulley on Caterpillar 320C excavator models. The removal procedure involves using a combination puller tool to remove the nut and washer from the crankshaft, then using a puller tool to remove the pulley. The installation procedure specifies cleaning the crankshaft, placing the pulley in position, and securing it with a washer and nut tightened to the specified torque. Tools required include a combination puller, socket, and cleaning supplies.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
Caterpillar Cat 320C L Excavator (Prefix DBG) Service Repair Manual (DBG00001...fhjsekdmdm3e
This document provides instructions for removing and installing a crankshaft pulley on Caterpillar 320C excavator models. The removal procedure involves using a combination puller tool to remove the nut and washer from the crankshaft, then using a puller tool to remove the pulley. The installation procedure specifies cleaning the crankshaft, placing the pulley in position, and securing it with a washer and nut tightened to the specified torque. Tools required include a combination puller, socket, and cleaning supplies.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
Caterpillar Cat 320C L Excavator (Prefix DBG) Service Repair Manual (DBG00001...f8usjejkdmmd
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
Caterpillar Cat 320C L Excavator (Prefix DBG) Service Repair Manual (DBG00001...8dusjkdmmdmd
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
Caterpillar Cat 320C L Excavator (Prefix DBG) Service Repair Manual (DBG00001...fujsekkdmmdm
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
Similar to Caterpillar Cat 320C LN Excavator (Prefix DBG) Service Repair Manual (DBG00001 and up).pdf (20)
Caterpillar Cat 320C U Excavator (Prefix PAC) Service Repair Manual (PAC00001...wenxian17880
This document provides instructions for removing and installing various engine components on a Caterpillar 320C excavator. The instructions covered include:
- Removing and installing the flywheel housing.
- Removing and installing the crankshaft pulley.
- Removing the crankshaft front seal.
- Installing the crankshaft front seal.
- Removing the idler gear from the front gear group.
- Installing the idler gear.
The document provides detailed step-by-step instructions accompanied by illustrations. Safety and cleaning notes are also included.
Caterpillar Cat 320C S 320CS Excavator (Prefix BCN) Service Repair Manual (BC...wenxian17880
This document provides instructions for removing and installing various fuel system components on a 320C excavator model powered by a 3066 engine. The components include the fuel filter base, fuel injection lines, fuel injection nozzles, fuel shutoff solenoid, and fuel injection pump. The procedures describe disconnecting fuel lines, removing mounting hardware, and ensuring openings are plugged to prevent contamination. Special tools may be required and safety precautions are noted.
Caterpillar Cat 320C LU 320CLU Excavator (Prefix PAC) Service Repair Manual (...wenxian17880
This document provides instructions for removing and installing various engine components on a Caterpillar 320C excavator engine, including:
- Removing and installing the flywheel housing.
- Removing and installing the crankshaft pulley.
- Removing the crankshaft front seal.
- Installing a new crankshaft front seal.
- Removing the idler gear from the front gear group.
- Instructions reference other documents for removing additional gears.
The document provides instructions for disassembling and assembling the travel motor of a 320C excavator. It lists 28 steps for disassembling the travel motor into individual components such as the piston guide, pistons, springs, seals, bearings, and housing. It also warns of safety hazards like released spring forces. The assembly procedure is not described but refers to assembling the components in reverse order of disassembly. Proper cleaning and installation of new seals is emphasized to prevent contamination of hydraulic components.
This document provides instructions for removing and installing the engine oil pump on a Caterpillar 320C LN excavator. It outlines 10 steps to remove the pump, including removing the front housing, cover, gears, seals and spindle. It then outlines 8 steps to install the pump, including heating components, installing seals, gears and the cover. Safety notices are provided regarding keeping components clean and containing fluids.
The document provides instructions for disassembling a swing drive. The steps include:
1. Removing various gears, shafts, washers, and bearings from within the swing drive assembly.
2. Using retaining ring pliers and a driver group to remove retaining rings and pins.
3. Pressing out bearings, seals, and a shaft from the swing drive housing.
4. Removing a ring gear, carrier assembly, and cage from the housing.
The purpose is to fully disassemble the swing drive for repair or replacement of parts. Cleanliness is emphasized to prevent contamination of hydraulic components.
This document provides instructions for removing and installing the fuel filter base and fuel injection lines on a Caterpillar 320C excavator with a 3066 engine. The summary is:
1. The removal procedure describes disconnecting the fuel lines from the fuel filter base and filter, and removing two bolts to take off the base.
2. The installation procedure outlines reconnecting the fuel lines to the base and filter, and securing the base with two bolts.
3. Removing the fuel injection lines involves disconnecting them from the nozzles and pump, and removing mounting bolts and clamps. Installation is the reverse of removal.
Caterpillar Cat 320C L Excavator (Prefix JTG) Service Repair Manual (JTG00001...wenxian17880
The document provides instructions for disassembling and assembling the travel motor of a 320C excavator. It lists 28 steps for disassembling the travel motor into individual components. This includes removing bolts, seals, plates, springs, pistons, and bearings. Cleanliness is emphasized to prevent contamination. The document then lists the assembly procedure, but does not provide the specific steps, instead stating to reverse the disassembly process. Proper torque values and identification marks are recommended for correct reassembly.
Caterpillar Cat 320C L Excavator (Prefix DBG) Service Repair Manual (DBG00001...wenxian17880
This document provides instructions for removing and installing various engine components on Caterpillar 320C excavators, including the flywheel, crankshaft rear seal, flywheel housing, crankshaft pulley, and crankshaft front seal. The procedures describe using various tools to remove and install each part, providing illustrations to supplement the text instructions. Safety and contamination prevention notices are also included.
Caterpillar Cat 320C L 320CL Excavator (Prefix RAW) Service Repair Manual (RA...wenxian17880
1. The document provides instructions for removing and installing various engine components on Caterpillar 320C and 320C L excavators, including the flywheel, crankshaft rear seal, flywheel housing, and crankshaft pulley.
2. The procedures describe using various tools to remove parts and installing replacement parts, taking care to keep parts clean and apply retaining compounds as needed.
3. Safety notices are provided to contain fluids and wear protective gloves when handling hot parts.
Caterpillar Cat 320C L 320CL Excavator (Prefix HKT) Service Repair Manual (HK...wenxian17880
The document provides installation instructions for auxiliary control valves F1, F4, F2, and F3 on an excavator model 320C. It involves connecting pilot lines, hoses, electrical connectors, and mounting the control valves. Tools like a vacuum cap are used to minimize hydraulic fluid leakage during installation. High efficiency hydraulic filters are installed before filling the tank and swing drive with clean hydraulic oil.
Caterpillar Cat 320C L 320CL Excavator (Prefix BCN) Service Repair Manual (BC...wenxian17880
This document provides instructions for removing and installing various fuel system components on a 320C excavator model powered by a 3066 engine. The components include the fuel filter base, fuel injection lines, fuel injection nozzles, fuel shutoff solenoid, and fuel injection pump. The procedures describe disconnecting fuel lines, removing mounting hardware, and ensuring openings are plugged to prevent contamination. Tools required are also listed.
1. The document provides instructions for removing and installing various engine components on Caterpillar 320C and 320C L excavators, including the flywheel, crankshaft rear seal, flywheel housing, and crankshaft pulley.
2. The procedures describe using various tools to remove parts and installing replacement parts, taking care to keep parts clean and applying retaining compounds as specified.
3. Detailed illustrations accompany each procedure to show the component locations and installation/removal steps.
The document provides instructions for removing and disassembling a travel motor from an excavator model 320C. It involves draining oil, removing bolts and hoses, lifting the motor out using threaded rods and a lifting device, and then disassembling internal components like the head, spool, springs, seals and pistons using various specialty tools. Cleanliness is emphasized to prevent contamination of hydraulic components during disassembly and reassembly.
This document provides instructions for removing and installing track components on a 320C excavator. It describes:
1) Releasing track tension and removing the track carrier roller or track roller using hydraulic jacks and lifting tools.
2) Cleaning mounting surfaces and installing the components using lifting devices, making sure rollers rotate smoothly.
3) Separating the track by removing the master pin and spacers after releasing tension and placing a block under the track.
The document provides installation instructions for auxiliary control valves F1, F4, F2, and F3 on an excavator model 320C. It involves connecting pilot lines, hoses, electrical connectors, and mounting the control valves. Tools like a vacuum cap are used to minimize hydraulic fluid leakage during installation. High efficiency hydraulic filters are installed before filling the tank and swing drive with clean hydraulic oil.
This document provides instructions for removing and installing fuel injection lines, nozzles, and pumps on a Caterpillar 3066 engine. It describes disconnecting the lines from the fuel injection pump, nozzles, and manifold. It also details using puller tools to remove nozzles and ensuring caps are used to prevent contamination. Proper alignment of parts and torquing of bolts is emphasized during installation.
This document provides instructions for removing and installing various fuel system components on a Caterpillar 320C excavator engine, including:
- Removing and installing the fuel filter base.
- Removing and installing the fuel injection lines.
- Removing the fuel injection nozzles.
- Installing the fuel injection nozzles.
- Removing and installing the fuel shutoff solenoid.
- Removing the fuel injection pump.
The procedures provide detailed steps for disconnecting fuel lines, removing mounting hardware, and ensuring openings are capped to prevent contamination. Required tools are listed for each job. Safety notices emphasize keeping parts clean and containing fluids.
The document provides instructions for disassembling a swing drive. The steps include:
1. Removing various gears, shafts, washers, and bearings from within the swing drive assembly.
2. Using retaining ring pliers and a driver group to remove retaining rings and pins.
3. Pressing out bearings and seals from the swing drive housing.
4. Marking the swing drive location prior to removal for installation purposes.
This document provides instructions for removing and installing various engine components on Caterpillar 320C excavators, including the flywheel, crankshaft rear seal, flywheel housing, crankshaft pulley, and crankshaft front seal. The procedures describe using various tools to remove and install each part, providing illustrations to supplement the text instructions. Safety and contamination prevention notices are also included.
How To Fix The Key Not Detected Issue In Mercedes CarsIntegrity Motorcar
Experiencing a "Key Not Detected" problem in your Mercedes? Don’t take it for granted. Go through this presentation to find out the exact nature of the issue you are dealing with. Have your vehicle checked by a certified professional if necessary.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
What Are The Immediate Steps To Take When The VW Temperature Light Starts Fla...Import Motorworks
Learn how to respond when the red temperature light flashes in your VW with this presentation. From checking coolant levels to seeking professional help, follow these steps promptly to prevent engine damage and ensure safety on the road.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Learn why monitoring your Mercedes' Exhaust Back Pressure (EBP) sensor is crucial. Understand its role in engine performance and emission reduction. Discover five warning signs of EBP sensor failure, from loss of power to increased emissions. Take action promptly to avoid costly repairs and maintain your Mercedes' reliability and efficiency.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Your VW's camshaft position sensor is crucial for engine performance. Signs of failure include engine misfires, difficulty starting, stalling at low speeds, reduced fuel efficiency, and the check engine light. Prompt inspection and replacement can prevent further damage and keep your VW running smoothly.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Is Recruitment Processing Outsourcing (RPO) Services?Impeccable HR
Impeccable HR provides a wide range of RPO services for your bulk hiring needs within a stipulated period. They meticulously build RPO solutions to improve your recruitment process. RPO services are great for budget-conscious recruiters who want high-quality personnel.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR DBG
Configuration: 320C, 320C L, 320C LN Excavators DBG00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01567260
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Always wear protective gloves when handling parts that have been
heated.
1. Perform the following procedure, if the ring gear was removed from the flywheel:
a. Heat the ring gear to 150 °C (302 °F) in an oven.
1/3(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
3. b. Press the ring gear onto the flywheel.
Note: Prior to the installation of the flywheel, refer to Specifications, "Flywheel" for
information on checking the flywheel assembly for flatness.
Illustration 1 g00605504
2. Install Tool (A), a strap, and a suitable lifting device onto flywheel (6) .
3. Install flywheel (6). The weight of the flywheel is 50 kg (110 lb).
Illustration 2 g00605501
4. Install six bolts (5) in order to secure flywheel (6) onto the crankshaft. Tighten the bolts to a
torque of 83 ± 5 N·m (61 ± 4 lb ft).
5. Remove Tool (A) from the flywheel.
2/3(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
5. Illustration 3 g00605497
6. Place the inner ring (4) in position on the flywheel.
7. Install four socket head bolts (3) in order to secure the inner ring (4) to the flywheel.
Illustration 4 g00605492
8. Place the adapter (2) in position on the flywheel housing.
9. Install twelve bolts and washers (1) in order to secure the adapter (2) on the flywheel
housing.
10. Check the flywheel runout. Refer to Testing and Adjusting, "Flywheel Housing - Inspect"
for more information on flywheel runout.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 22 12:20:55 UTC+0800 2019
3/3(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR DBG
Configuration: 320C, 320C L, 320C LN Excavators DBG00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01135944
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
B
5P-7312 Seal Distorter 1
5P-7338 Distorter Ring 2
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
1/3(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
7. of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00604840
Note: If the oil seal shows a sign of oil leaks, remove the wear sleeve and the oil seal.
1. Drill three evenly spaced 3 mm (0.12 inch) holes in crankshaft rear seal (1).
2. Use Tool (A) to remove the crankshaft rear seal.
Illustration 2 g00604844
3. Use Tool (B) to remove the wear sleeve (2) (not shown) from the rear of the crankshaft.
Note: When you are removing the wear sleeve, take extreme care not to damage the
crankshaft.
2/3(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR DBG
Configuration: 320C, 320C L, 320C LN Excavators DBG00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615317
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
9U-6169 Installer 1
9U-6171 Locator 1
9U-6172 Bolt 2
5P-8247 Hard Washer 1
6V-3303 Bolt 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. To install a new wear sleeve that is complete with a seal, use 169-5464 Quick Cure Primer
to clean the outer diameter of the crankshaft and the inside diameter of the wear sleeve.
Apply 4C-9507 Retaining Compound to the faces of all the mating parts.
1/3(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
9. Illustration 1 g00604874
2. Install a new wear sleeve that is complete with a seal (1) (not shown) with Tool (A), as
follows:
Illustration 2 g00604875
a. Install 9U-6171 Locator (3) onto the crankshaft with 9U-6172 Bolt (4).
b. Put the new wear sleeve that is complete with a seal in 9U-6169 Installer (2).
c. Put 6V-3303 Bolt (6) through 5P-8247 Hard Washer (5) and 9U-6169 Installer (2)
and thread into 9U-6171 Locator (3).
d. Push the wear sleeve that is complete with a seal onto the crankshaft until 9U-6169
Installer (2) bottoms out.
2/3(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
10. Illustration 3 g00604874
e. Remove Tool (A) and check crankshaft rear seal (1) (not shown) for correct
installation.
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 22 12:22:47 UTC+0800 2019
3/3(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR DBG
Configuration: 320C, 320C L, 320C LN Excavators DBG00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i05421135
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
B 1P-0510 Driver Group 1
Start By:
A. Remove the electric starting motor.
B. Remove the flywheel and ring gear.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
12. Illustration 1 g00605593
1. Install Tooling (A) , a strap, and a suitable lifting device onto flywheel housing (2) .
2. Remove bolts (1) and the washers that secure flywheel housing (2) to the cylinder block.
Note: Identify the four shorter bolts for later installation into the flywheel housing.
3. Remove flywheel housing (2) . The weight of the flywheel is approximately.29 kg (65 lb).
4. Check oil seal (3) for serviceability. If necessary, replace the oil seal and crankshaft wear
sleeve.
Illustration 2 g00605601
5. Use Tooling (B) in order to remove the oil seal (3) (not shown).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
2/3(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
13. B 9U-6170 Installer Gp 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 3 g00605593
1. Clean old gasket material (4) from the mating surfaces of the cylinder block and the
flywheel housing. Install a new gasket on the cylinder block.
2. Place flywheel housing (2) in position on the cylinder block.
3. Install the washers and bolts (1) in order to secure flywheel housing (2) to the cylinder
block.
4. Use Tooling (B) in order to install the oil seal (3) , and the crankshaft wear sleeve (not
shown).
End By:
a. Install the flywheel.
b. Install the electric starting motor.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 22 12:23:43 UTC+0800 2019
3/3(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR DBG
Configuration: 320C, 320C L, 320C LN Excavators DBG00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01578488
Crankshaft Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2321 Combination Puller 1
B 6V-9120 Socket (1)
1
( 1 )
Tool (B) is a 46 mm socket.
Start By:
A. Remove the V-belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
15. Illustration 1 g00604778
1. Use Tool (B) to remove nut (1) and washer (2) from the threaded end of the crankshaft.
Illustration 2 g00604784
2. Use Tool (A) to remove crankshaft pulley (3) from the engine.
2/4(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
16. Illustration 3 g00604792
3. If it is necessary to remove the wear sleeve (4) from the crankshaft pulley (3), use a hammer
and a chisel. Hold the chisel at right angles to the surface of the wear sleeve. Tap the wear
sleeve in three places. You can remove the wear sleeve once the tension is released.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 4 g00604778
3/4(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
17. 1. Put crankshaft pulley (3) in position on the engine.
2. Install washer (2) and nut (1). Use Tool (B) to tighten nut (1) to a torque of 490 ± 10 N·m
(361 ± 7 lb ft).
End By: Install the V-belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 22 12:24:39 UTC+0800 2019
4/4(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR DBG
Configuration: 320C, 320C L, 320C LN Excavators DBG00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01131366
Crankshaft Front Seal - Remove
SMCS - 1160-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
Start By:
A. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/2(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
19. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00529162
1. Drill three evenly spaced 3 mm (0.12 inch) holes in crankshaft front seal (1) .
2. Use Tool (A) and remove crankshaft front seal (1). Remove the seal evenly by alternating
the position of Tool (A) from hole to hole.
Note: Do not damage the flange of the crankshaft during the removal process for the
crankshaft front seal.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 22 12:25:34 UTC+0800 2019
2/2(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR DBG
Configuration: 320C, 320C L, 320C LN Excavators DBG00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i02080454
Crankshaft Front Seal - Install
SMCS - 1160-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6180 Front Seal Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
21. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
22. Illustration 1 g00612743
1. Clean the faces of all the mating parts. Apply a thin coat of clean engine oil to a new
crankshaft front seal.
2. Install new crankshaft front seal (1) in the front housing with Tool (A) .
3. Remove Tooling (A) and check crankshaft front seal (1) for correct installation.
4. Apply clean engine oil to the face of the crankshaft pulley that will be in contact with the
new crankshaft front seal.
End By: Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 22 12:26:30 UTC+0800 2019
2/2(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR DBG
Configuration: 320C, 320C L, 320C LN Excavators DBG00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615339
Gear Group (Front) - Remove - Idler Gear Only
SMCS - 1206-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6148 Idler Shaft Puller 1
B 1P-0510 Driver Group 1
Start By:
A. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
1/5(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
24. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Note: Before removal, ensure that the marks on the timing gears are in alignment. Align the
fuel injection drive gear with the "33" mark with the "3" mark on the idler gear. Make an
alignment of the "2" mark on the camshaft gear with the "22" mark on the idler gear. Align
the "1" mark on the crankshaft gear with the "11" mark on the idler gear. The No. 1 cylinder
is at the top center position when these marks are in alignment.
Illustration 1 g00611568
1. Remove idler gear bolt (1) and the washer from the idler gear shaft .
2. Remove thrust plate (2) from the idler gear shaft.
2/5(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...