The document provides instructions for removing and installing a fuel injection pump gear on a Caterpillar C7.1 engine. The removal procedure involves using turning tools to lock the crankshaft and camshaft positions, marking the gear alignments, and using a puller tool to remove the gear. The installation procedure specifies cleaning and aligning the gears using timing marks, applying and tightening the nut while removing backlash, and lubricating the gears.
The document provides instructions for removing the fuel injector from a Caterpillar 320D2 excavator engine. It lists the required tools which include a fuel injector puller and capping kit. The procedure involves disconnecting fuel lines from the injector, plugging the injector, removing mounting bolts and clamps, and using a puller tool to remove the fuel injector from the engine.
The document provides instructions for removing and installing the fuel injection pump gear on a Caterpillar C7.1 engine. The 3 step summary is:
1. To remove the gear, lock the camshaft and crankshaft, mark alignment of gears, and use a puller tool to remove the gear from the fuel injection pump shaft.
2. To install the gear, ensure proper alignment of gears using timing marks, install the gear on the fuel injection pump shaft, and tighten the nut while applying pressure to remove backlash.
3. Lubricate the gear teeth and install the front cover after installing the fuel injection pump gear.
Caterpillar cat 322 c l 322cl hydraulic excavator (prefix hek) service repair...udfjjjskekdme
This document provides instructions for servicing components of a 322C L Hydraulic Excavator including removing and installing a unit injector hydraulic pump, turbocharger, exhaust manifold, and air inlet heater solenoid. The procedures include using required tools, cleaning parts, applying sealants, and torquing bolts to specified values. Illustrations and part numbers are provided to aid in disassembly and reassembly.
This document provides instructions for removing and installing a unit injector, unit injector sleeve, and turbocharger from a C9.3 Industrial Engine. The unit injector removal procedure involves disconnecting electrical and fuel lines, loosening mounting bolts, and extracting the injector. Installation requires cleaning, lubricating seals, and tightening bolts. The sleeve procedure includes draining coolant, cutting threads to remove the old sleeve, cleaning the bore, applying retaining compound to the new sleeve, and installing with a hammer and driver. The turbocharger removal involves disconnecting coolant and air lines and removing mounting nuts. Installation requires applying anti-seize to bolts and tightening clamps and nuts.
Caterpillar cat 329 el excavator (prefix plw) service repair manual (plw00001...ufjjjskkemmd
This document provides instructions for removing and installing the crankshaft timing ring on a Caterpillar C7.1 engine. It describes removing the crankshaft, then removing the allen head screws and timing ring from the crankshaft. For installation, it instructs to clean the crankshaft flange, position the new timing ring on the crankshaft, and install new allen head screws to secure it. Proper cleaning and protection of parts from contamination is emphasized throughout.
The document provides instructions for removing and installing various engine components on a Caterpillar 330D2 excavator, including the engine oil pump, water pump, water temperature regulator, and flywheel. The procedures note required tools and safety precautions. Components must be clean and free of damage, with replacement of worn parts. Proper torque values are specified for reinstallation of components.
The document provides instructions for removing and installing various engine components on a Caterpillar C9.3B industrial engine. It includes steps for removing and installing the crankshaft rear seal, flywheel housing, vibration damper and pulley, crankshaft front seal, front cover, and housing (front). Diagrams and part numbers for required tools are provided for each procedure. The document is part of a service manual for Caterpillar technicians repairing C9.3B engines.
Caterpillar cat 320 d lrr excavator (prefix dhe) service repair manual (dhe00...fjsekdmmeed
This document provides instructions for removing, disassembling, assembling, and installing the engine oil pump and water pump on a Caterpillar 320D LRR excavator with a C6.4 engine. The oil pump removal process involves taking off the front housing cover and various gears. The water pump removal requires removing the belt and pump pulley. Both pumps are disassembled by removing mounting components using various tools. Reassembly follows the reverse order and procedures provide guidance on cleaning, inspection and installation of seals.
The document provides instructions for removing the fuel injector from a Caterpillar 320D2 excavator engine. It lists the required tools which include a fuel injector puller and capping kit. The procedure involves disconnecting fuel lines from the injector, plugging the injector, removing mounting bolts and clamps, and using a puller tool to remove the fuel injector from the engine.
The document provides instructions for removing and installing the fuel injection pump gear on a Caterpillar C7.1 engine. The 3 step summary is:
1. To remove the gear, lock the camshaft and crankshaft, mark alignment of gears, and use a puller tool to remove the gear from the fuel injection pump shaft.
2. To install the gear, ensure proper alignment of gears using timing marks, install the gear on the fuel injection pump shaft, and tighten the nut while applying pressure to remove backlash.
3. Lubricate the gear teeth and install the front cover after installing the fuel injection pump gear.
Caterpillar cat 322 c l 322cl hydraulic excavator (prefix hek) service repair...udfjjjskekdme
This document provides instructions for servicing components of a 322C L Hydraulic Excavator including removing and installing a unit injector hydraulic pump, turbocharger, exhaust manifold, and air inlet heater solenoid. The procedures include using required tools, cleaning parts, applying sealants, and torquing bolts to specified values. Illustrations and part numbers are provided to aid in disassembly and reassembly.
This document provides instructions for removing and installing a unit injector, unit injector sleeve, and turbocharger from a C9.3 Industrial Engine. The unit injector removal procedure involves disconnecting electrical and fuel lines, loosening mounting bolts, and extracting the injector. Installation requires cleaning, lubricating seals, and tightening bolts. The sleeve procedure includes draining coolant, cutting threads to remove the old sleeve, cleaning the bore, applying retaining compound to the new sleeve, and installing with a hammer and driver. The turbocharger removal involves disconnecting coolant and air lines and removing mounting nuts. Installation requires applying anti-seize to bolts and tightening clamps and nuts.
Caterpillar cat 329 el excavator (prefix plw) service repair manual (plw00001...ufjjjskkemmd
This document provides instructions for removing and installing the crankshaft timing ring on a Caterpillar C7.1 engine. It describes removing the crankshaft, then removing the allen head screws and timing ring from the crankshaft. For installation, it instructs to clean the crankshaft flange, position the new timing ring on the crankshaft, and install new allen head screws to secure it. Proper cleaning and protection of parts from contamination is emphasized throughout.
The document provides instructions for removing and installing various engine components on a Caterpillar 330D2 excavator, including the engine oil pump, water pump, water temperature regulator, and flywheel. The procedures note required tools and safety precautions. Components must be clean and free of damage, with replacement of worn parts. Proper torque values are specified for reinstallation of components.
The document provides instructions for removing and installing various engine components on a Caterpillar C9.3B industrial engine. It includes steps for removing and installing the crankshaft rear seal, flywheel housing, vibration damper and pulley, crankshaft front seal, front cover, and housing (front). Diagrams and part numbers for required tools are provided for each procedure. The document is part of a service manual for Caterpillar technicians repairing C9.3B engines.
Caterpillar cat 320 d lrr excavator (prefix dhe) service repair manual (dhe00...fjsekdmmeed
This document provides instructions for removing, disassembling, assembling, and installing the engine oil pump and water pump on a Caterpillar 320D LRR excavator with a C6.4 engine. The oil pump removal process involves taking off the front housing cover and various gears. The water pump removal requires removing the belt and pump pulley. Both pumps are disassembled by removing mounting components using various tools. Reassembly follows the reverse order and procedures provide guidance on cleaning, inspection and installation of seals.
This document provides instructions for removing and installing various engine components on a Caterpillar C11 Industrial Engine, including:
1) Valves, guides, and seat inserts - Removal and installation procedures outlined for each part.
2) Engine oil filter base - Procedure to remove the base and disassemble its components.
3) Safety notices are provided throughout to warn of spring pressures and ensure clean parts.
This document provides instructions for removing and installing a crankshaft from a C7.1 engine. It describes removing components like the front housing, oil pump, seals and bearings. It then instructs how to attach lifting slings to the crankshaft and remove it from the engine block. Detailed steps are provided for cleaning, inspecting, and installing the crankshaft along with related components like thrust washers, bearing shells and caps. Tolerances and torques are specified to ensure proper installation.
Caterpillar cat 323 d l excavator (prefix cwg) service repair manual (cwg0000...fjskksmem
The document provides instructions for removing and installing the crankshaft on a Caterpillar C6.4 engine. To remove the crankshaft, the front housing, rear seal, flywheel housing and oil pan must first be removed. Then the connecting rod caps, main bearing caps and pistons can be taken off to allow removal of the crankshaft. Installation follows the reverse order, with care taken to clean parts and apply specified torques. End play must be checked after installation is complete.
Caterpillar cat 938 g ii wheel loader (prefix phn) service repair manual (phn...fjsjjekdkme
The document provides instructions for disassembling and assembling the transmission oil pump and relief valve (transmission hydraulic control) for a Caterpillar 938G II wheel loader. It includes detailed steps and illustrations for removing parts like gears, bearings, seals and covers. Tools required are also listed. The document is from a Caterpillar service manual and aims to guide maintenance technicians in properly servicing these components.
The document provides instructions for removing and installing a fuel injection pump on a 320DL excavator with a C6.4 engine. It describes:
1) Removing components like hoses, tubes, brackets and gears to access the fuel injection pump.
2) Using identification marks and tooling to properly align gears during removal and installation.
3) Cleaning components thoroughly before installation to prevent contamination.
4) Installing the fuel injection pump by reversing the removal steps and ensuring proper torque of fasteners.
Caterpillar cat 320 d lrr excavator (prefix ejt) service repair manual (ejt00...fjsekdmmeed
The document provides instructions for removing and installing the flywheel and crankshaft pulley on a 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like the flywheel, flywheel housing, and crankshaft pulley. Detailed steps and illustrations are provided for disassembling and reassembling these parts, including cleaning, inspecting, and applying sealants to mating surfaces. Safety notices advise keeping parts clean and containing fluids.
Caterpillar cat 320 d l excavator (prefix dhk) service repair manual (dhk0000...fkjsekksmem
This document provides instructions for removing and installing the boom cylinder on a 320D and 320D L excavator. It outlines the required tools and safety precautions. The removal process involves releasing hydraulic pressure, removing attachment points, and lifting the cylinder out of place. Reinstallation is the reverse of removal. Torque specifications are provided for correct assembly.
Caterpillar cat 305 cr mini hydraulic excavator (prefix dgt) service repair m...fjskekfseik
The document provides instructions for removing the swivel on a 305CR Mini Hydraulic Excavator. It lists the required tools and notes to release hydraulic pressure and remove the cab first. The procedure involves using plugs and caps to seal ports while removing 4 bolts to detach the swivel assembly.
This document provides instructions for removing and installing various engine components on a Caterpillar 330 L excavator, including:
1. The cylinder head removal procedure involves removing fuel injection lines, exhaust manifold, rocker shaft and pushrods, and bolts holding the head to the cylinder block.
2. Installing the cylinder head requires cleaning surfaces, installing gaskets and bolts, adjusting valves, and reinstalling other removed components.
3. Removal of the spacer plate requires removing seals and installing a new gasket, while installation requires cleaning and installing the plate with new seals.
Caterpillar cat 312 d excavator (prefix hcw) service repair manual (hcw00001 ...fksjksmmde
1. The document provides instructions for removing and installing a crankshaft position sensor on a Caterpillar C4.2 engine.
2. The removal procedure involves disconnecting the electrical connector and removing the mounting bolts.
3. The installation procedure specifies cleaning parts, applying threadlock to bolts, torquing bolts to specification, and connecting the electrical connector.
Caterpillar cat 725 c articulated truck (prefix lfb) service repair manual (l...ifse9diodkdk
This document provides instructions for disassembling and assembling the torque converter in a 725C articulated truck. It describes 43 steps to disassemble the various components of the torque converter including removing bolts, seals, bearings, races, and housing pieces. It then lists the required tools and provides a brief assembly procedure, noting to clean all surfaces and apply locking compound or O-ring assembly compound as needed.
Caterpillar cat 329 f l excavator (prefix erl) service repair manual (erl0000...ifse9diodkdk
1. The document provides removal and installation instructions for inlet and exhaust valves on a Caterpillar 329F L Excavator with a C7.1 engine.
2. The procedure involves using special tools to compress the valve springs to remove the valve keepers and other components, and then reversing the process to install new components.
3. Technicians are instructed to clean and inspect all parts, lubricate the valves, and ensure proper valve depth before installing and securing the valve assembly components.
Caterpillar cat 329 el excavator (prefix pty) service repair manual (pty00001...ifse9diodkdk
The document provides instructions for removing and installing the front cover on a Caterpillar 329E excavator engine. The removal procedure involves taking out the crankshaft pulley, fan if equipped, and front seal before removing bolts to take off the front cover. The installation procedure specifies cleaning surfaces, installing a new gasket on guide studs, placing the front cover on with bolts, and using a front cover alignment tool.
Caterpillar cat 329 e excavator (prefix pty) service repair manual (pty00001 ...ifse9diodkdk
The document provides instructions for removing and installing the front cover on a Caterpillar 329E excavator engine. The removal procedure involves taking out the crankshaft pulley, fan if equipped, and front seal before removing bolts to take off the front cover. The installation procedure specifies cleaning surfaces, installing a new gasket on guide studs, placing the front cover on with bolts, and using a front cover alignment tool.
This document provides instructions for removing the engine oil filter base and oil cooler from a Caterpillar 329D LN excavator. The key steps are:
1. Drain engine oil and coolant from the systems before removal to contain fluids.
2. For a remote-mounted filter base, use a strap wrench to remove the oil filter, then remove bolts and the filter base.
3. For an engine-mounted base, drain the cooling system, then remove hoses and bolts to separate the oil cooler from the engine.
Caterpillar cat 329 dl mobile hyd power unit excavator (prefix l5h) service r...ifse9diodkdk
This service repair manual provides instructions for removing and installing various engine components on a Caterpillar 329D L MOBILE HYD POWER UNIT, including:
- Removing and installing inlet and exhaust valve guides from the cylinder head.
- Removing and installing inlet and exhaust valve seat inserts in the cylinder head.
- Removing the engine oil filter base and oil cooler.
- Disassembling the remote or engine mounted engine oil filter base.
The document provides detailed step-by-step instructions, diagrams and safety notices for completing each procedure. Required tools are listed for each job.
Caterpillar cat 329 dl mobile hyd power unit excavator (prefix l5g) service r...ifse9diodkdk
This document provides instructions for disassembling the final drive of a 329D L Mobile Hydraulic Power Unit. It outlines 30 steps to fully disassemble the final drive, including removing gears, carriers, shafts, seals and other components. Various tools are required to secure, lift and remove parts. Cleanliness is important to prevent dirt from entering during disassembly.
Caterpillar cat 329 dl mobile hyd power unit excavator (prefix j9d) service r...ifse9diodkdk
This document provides the disassembly and assembly procedures for a travel motor on a 329DL Mobile Hydraulic Power Unit excavator. The disassembly procedure outlines 28 steps to dismantle the various components of the travel motor. The assembly procedure describes 19 steps to reassemble the travel motor components in reverse order. Proper cleaning and installation of new seals and gaskets is emphasized throughout.
Caterpillar cat 329 dl mobile hyd power unit excavator (prefix j8d) service r...ifse9diodkdk
The document provides instructions for disassembling the final drive of a 329DL Mobile Hydraulic Power Unit. It lists required tools and describes a 37 step process involving removing housing, gears, carriers, shafts, seals, and other components. Cleanliness is important to prevent dirt from entering during reassembly. Weights of removed parts are provided to assist with lifting.
This document provides instructions for removing the engine oil filter base and oil cooler from a Caterpillar 329D LN excavator. The key steps are:
1. Drain engine oil and coolant from the systems before removal to contain fluids.
2. For a remote-mounted filter base, use a strap wrench to remove the oil filter, then remove bolts and the filter base.
3. For an engine-mounted base, drain the cooling system, then remove hoses and bolts to separate the oil cooler from the engine.
This document provides instructions for disassembling the final drive on a Caterpillar 329D2 L excavator. The process involves:
1. Removing the final drive and separating it from the track assembly and travel motor.
2. Lifting the final drive and disassembling it into components like the cover, carrier assembly, ring gears, and main housing.
3. Using tools like pins, screws, and lifting devices to separate individual parts which are then cleaned and inspected.
4. Disassembling internal components of the carrier assembly like planetary gears and shafts.
The instructions describe each step in detail and include illustrations of the components and proper tooling to use. Safety notes are included about handling
This document provides instructions for removing the rear power take-off (RPTO) from a C7.1 engine. It outlines 10 steps to remove gears, adapters, seals and other components from the flywheel housing. Precautions are given to keep parts clean and ensure correct alignment of sleeves and oil holes. Required tools include a driver group. The process is reversed to install the RPTO following similar steps and precautions.
This document provides instructions for removing and installing various engine components on a Caterpillar C11 Industrial Engine, including:
1) Valves, guides, and seat inserts - Removal and installation procedures outlined for each part.
2) Engine oil filter base - Procedure to remove the base and disassemble its components.
3) Safety notices are provided throughout to warn of spring pressures and ensure clean parts.
This document provides instructions for removing and installing a crankshaft from a C7.1 engine. It describes removing components like the front housing, oil pump, seals and bearings. It then instructs how to attach lifting slings to the crankshaft and remove it from the engine block. Detailed steps are provided for cleaning, inspecting, and installing the crankshaft along with related components like thrust washers, bearing shells and caps. Tolerances and torques are specified to ensure proper installation.
Caterpillar cat 323 d l excavator (prefix cwg) service repair manual (cwg0000...fjskksmem
The document provides instructions for removing and installing the crankshaft on a Caterpillar C6.4 engine. To remove the crankshaft, the front housing, rear seal, flywheel housing and oil pan must first be removed. Then the connecting rod caps, main bearing caps and pistons can be taken off to allow removal of the crankshaft. Installation follows the reverse order, with care taken to clean parts and apply specified torques. End play must be checked after installation is complete.
Caterpillar cat 938 g ii wheel loader (prefix phn) service repair manual (phn...fjsjjekdkme
The document provides instructions for disassembling and assembling the transmission oil pump and relief valve (transmission hydraulic control) for a Caterpillar 938G II wheel loader. It includes detailed steps and illustrations for removing parts like gears, bearings, seals and covers. Tools required are also listed. The document is from a Caterpillar service manual and aims to guide maintenance technicians in properly servicing these components.
The document provides instructions for removing and installing a fuel injection pump on a 320DL excavator with a C6.4 engine. It describes:
1) Removing components like hoses, tubes, brackets and gears to access the fuel injection pump.
2) Using identification marks and tooling to properly align gears during removal and installation.
3) Cleaning components thoroughly before installation to prevent contamination.
4) Installing the fuel injection pump by reversing the removal steps and ensuring proper torque of fasteners.
Caterpillar cat 320 d lrr excavator (prefix ejt) service repair manual (ejt00...fjsekdmmeed
The document provides instructions for removing and installing the flywheel and crankshaft pulley on a 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like the flywheel, flywheel housing, and crankshaft pulley. Detailed steps and illustrations are provided for disassembling and reassembling these parts, including cleaning, inspecting, and applying sealants to mating surfaces. Safety notices advise keeping parts clean and containing fluids.
Caterpillar cat 320 d l excavator (prefix dhk) service repair manual (dhk0000...fkjsekksmem
This document provides instructions for removing and installing the boom cylinder on a 320D and 320D L excavator. It outlines the required tools and safety precautions. The removal process involves releasing hydraulic pressure, removing attachment points, and lifting the cylinder out of place. Reinstallation is the reverse of removal. Torque specifications are provided for correct assembly.
Caterpillar cat 305 cr mini hydraulic excavator (prefix dgt) service repair m...fjskekfseik
The document provides instructions for removing the swivel on a 305CR Mini Hydraulic Excavator. It lists the required tools and notes to release hydraulic pressure and remove the cab first. The procedure involves using plugs and caps to seal ports while removing 4 bolts to detach the swivel assembly.
This document provides instructions for removing and installing various engine components on a Caterpillar 330 L excavator, including:
1. The cylinder head removal procedure involves removing fuel injection lines, exhaust manifold, rocker shaft and pushrods, and bolts holding the head to the cylinder block.
2. Installing the cylinder head requires cleaning surfaces, installing gaskets and bolts, adjusting valves, and reinstalling other removed components.
3. Removal of the spacer plate requires removing seals and installing a new gasket, while installation requires cleaning and installing the plate with new seals.
Caterpillar cat 312 d excavator (prefix hcw) service repair manual (hcw00001 ...fksjksmmde
1. The document provides instructions for removing and installing a crankshaft position sensor on a Caterpillar C4.2 engine.
2. The removal procedure involves disconnecting the electrical connector and removing the mounting bolts.
3. The installation procedure specifies cleaning parts, applying threadlock to bolts, torquing bolts to specification, and connecting the electrical connector.
Caterpillar cat 725 c articulated truck (prefix lfb) service repair manual (l...ifse9diodkdk
This document provides instructions for disassembling and assembling the torque converter in a 725C articulated truck. It describes 43 steps to disassemble the various components of the torque converter including removing bolts, seals, bearings, races, and housing pieces. It then lists the required tools and provides a brief assembly procedure, noting to clean all surfaces and apply locking compound or O-ring assembly compound as needed.
Caterpillar cat 329 f l excavator (prefix erl) service repair manual (erl0000...ifse9diodkdk
1. The document provides removal and installation instructions for inlet and exhaust valves on a Caterpillar 329F L Excavator with a C7.1 engine.
2. The procedure involves using special tools to compress the valve springs to remove the valve keepers and other components, and then reversing the process to install new components.
3. Technicians are instructed to clean and inspect all parts, lubricate the valves, and ensure proper valve depth before installing and securing the valve assembly components.
Caterpillar cat 329 el excavator (prefix pty) service repair manual (pty00001...ifse9diodkdk
The document provides instructions for removing and installing the front cover on a Caterpillar 329E excavator engine. The removal procedure involves taking out the crankshaft pulley, fan if equipped, and front seal before removing bolts to take off the front cover. The installation procedure specifies cleaning surfaces, installing a new gasket on guide studs, placing the front cover on with bolts, and using a front cover alignment tool.
Caterpillar cat 329 e excavator (prefix pty) service repair manual (pty00001 ...ifse9diodkdk
The document provides instructions for removing and installing the front cover on a Caterpillar 329E excavator engine. The removal procedure involves taking out the crankshaft pulley, fan if equipped, and front seal before removing bolts to take off the front cover. The installation procedure specifies cleaning surfaces, installing a new gasket on guide studs, placing the front cover on with bolts, and using a front cover alignment tool.
This document provides instructions for removing the engine oil filter base and oil cooler from a Caterpillar 329D LN excavator. The key steps are:
1. Drain engine oil and coolant from the systems before removal to contain fluids.
2. For a remote-mounted filter base, use a strap wrench to remove the oil filter, then remove bolts and the filter base.
3. For an engine-mounted base, drain the cooling system, then remove hoses and bolts to separate the oil cooler from the engine.
Caterpillar cat 329 dl mobile hyd power unit excavator (prefix l5h) service r...ifse9diodkdk
This service repair manual provides instructions for removing and installing various engine components on a Caterpillar 329D L MOBILE HYD POWER UNIT, including:
- Removing and installing inlet and exhaust valve guides from the cylinder head.
- Removing and installing inlet and exhaust valve seat inserts in the cylinder head.
- Removing the engine oil filter base and oil cooler.
- Disassembling the remote or engine mounted engine oil filter base.
The document provides detailed step-by-step instructions, diagrams and safety notices for completing each procedure. Required tools are listed for each job.
Caterpillar cat 329 dl mobile hyd power unit excavator (prefix l5g) service r...ifse9diodkdk
This document provides instructions for disassembling the final drive of a 329D L Mobile Hydraulic Power Unit. It outlines 30 steps to fully disassemble the final drive, including removing gears, carriers, shafts, seals and other components. Various tools are required to secure, lift and remove parts. Cleanliness is important to prevent dirt from entering during disassembly.
Caterpillar cat 329 dl mobile hyd power unit excavator (prefix j9d) service r...ifse9diodkdk
This document provides the disassembly and assembly procedures for a travel motor on a 329DL Mobile Hydraulic Power Unit excavator. The disassembly procedure outlines 28 steps to dismantle the various components of the travel motor. The assembly procedure describes 19 steps to reassemble the travel motor components in reverse order. Proper cleaning and installation of new seals and gaskets is emphasized throughout.
Caterpillar cat 329 dl mobile hyd power unit excavator (prefix j8d) service r...ifse9diodkdk
The document provides instructions for disassembling the final drive of a 329DL Mobile Hydraulic Power Unit. It lists required tools and describes a 37 step process involving removing housing, gears, carriers, shafts, seals, and other components. Cleanliness is important to prevent dirt from entering during reassembly. Weights of removed parts are provided to assist with lifting.
This document provides instructions for removing the engine oil filter base and oil cooler from a Caterpillar 329D LN excavator. The key steps are:
1. Drain engine oil and coolant from the systems before removal to contain fluids.
2. For a remote-mounted filter base, use a strap wrench to remove the oil filter, then remove bolts and the filter base.
3. For an engine-mounted base, drain the cooling system, then remove hoses and bolts to separate the oil cooler from the engine.
This document provides instructions for disassembling the final drive on a Caterpillar 329D2 L excavator. The process involves:
1. Removing the final drive and separating it from the track assembly and travel motor.
2. Lifting the final drive and disassembling it into components like the cover, carrier assembly, ring gears, and main housing.
3. Using tools like pins, screws, and lifting devices to separate individual parts which are then cleaned and inspected.
4. Disassembling internal components of the carrier assembly like planetary gears and shafts.
The instructions describe each step in detail and include illustrations of the components and proper tooling to use. Safety notes are included about handling
This document provides instructions for removing the rear power take-off (RPTO) from a C7.1 engine. It outlines 10 steps to remove gears, adapters, seals and other components from the flywheel housing. Precautions are given to keep parts clean and ensure correct alignment of sleeves and oil holes. Required tools include a driver group. The process is reversed to install the RPTO following similar steps and precautions.
This document provides instructions for removing and installing a crankshaft from a C7.1 engine. It describes removing components like the front housing, oil pump, seals and bearings. It then instructs how to attach lifting slings to the crankshaft and remove it from the engine block. Detailed steps are provided for cleaning and inspecting the crankshaft and installing new bearings, thrust washers and seals before reinstalling the crankshaft and torquing the bolts to the specified values. Clear illustrations supplement the text instructions.
Caterpillar cat 329 d2 l excavator (prefix tmj) service repair manual (tmj000...ifse9diodkdk
The document provides instructions for removing and installing the engine oil pump on a Caterpillar C7.1 engine. It describes removing the oil pan, bolts and brackets holding the pump. It also details checking clearances after installation and installing the oil pan. Installation involves cleaning components, installing dowels and bolts, and checking gear backlash.
This document provides instructions for installing an engine oil pump on a C7.1 engine. It describes cleaning and inspecting the oil pump components and installing the cross over tube assembly with new gaskets. It also details reassembling the oil pump if disassembled, ensuring proper dowel pin locations, and installing the oil pump assembly onto the cylinder block and torquing the bolts. The installation is completed by installing a new gasket and the suction pipe.
This document provides instructions for removing the rear power take-off (RPTO) from a C7.1 engine. It outlines 10 steps to remove gears, hubs, adapters and other components from the flywheel housing. Precautions are given to keep parts clean and ensure correct alignment of sleeves and oil holes. Required tools include a driver group. The process concludes by removing the flywheel after the RPTO is disassembled.
Caterpillar cat 329 d ln excavator (prefix ebm) service repair manual (ebm000...ifse9diodkdk
The document provides instructions for removing and installing pistons and connecting rods on a Caterpillar C7 engine. It describes removing the cylinder head, oil pump, and piston cooling jets before removing each piston and connecting rod assembly. The connecting rod cap and bearings are removed, then the piston and connecting rod are separated. Reinstallation follows the reverse order, applying anti-seize compound and using tools to properly position the piston rings and install the connecting rod bearings.
Caterpillar cat 329 d l excavator (prefix yfw) service repair manual (yfw0000...ifse9diodkdk
This document provides instructions for disassembling and assembling the final drive of a 329D or 329D L excavator. It lists 37 steps for disassembly, removing components like gears, shafts, carriers and seals. It then lists 21 steps for assembly, providing details on cleaning parts, applying lubricants, setting bearing preloads using presses and shims, and installing seals and gears back into their original locations and orientations. Cleanliness is emphasized as important throughout the process.
Caterpillar cat 329 d l excavator (prefix ebm) service repair manual (ebm0000...ifse9diodkdk
This document provides instructions for removing and installing various engine components on a Caterpillar 329D L and 329D LN excavator, including:
- Removing and installing the engine oil pan, which involves draining the oil, removing bolts and the pan, cleaning surfaces, applying sealant, and reinstalling with new bolts and gasket.
- Removing and installing piston cooling jets by removing and replacing bolts to hold the jets in place.
- Procedures for removing pistons and connecting rods by identifying parts, removing caps and bolts, and pushing components out of the engine block.
Caterpillar cat 329 d excavator (prefix yfw) service repair manual (yfw00001 ...ifse9diodkdk
This document provides instructions for disassembling and assembling the final drive of a 329D or 329D L excavator. It lists 37 steps for disassembly, removing components like gears, shafts, bearings and seals. The assembly section outlines 15 steps, including pressing bearings into place, installing seals, and using shims to set the proper bearing preload when mounting the main housing onto the motor housing. Cleanliness is emphasized throughout as important for preventing contamination.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D2 EXCAVATOR GBA
Configuration: 320D2 & 320D2 L Excavators GBA00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 (Mech) Engines for Caterpillar Built Machines
Media Number -UENR0674-08 Publication Date -01/06/2015 Date Updated -23/01/2017
i04780457
Fuel Injection Pump Gear - Remove
SMCS - 1251-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1)
9U-7336 Crankshaft Turning Tool 1
A(2)
5P-7305 Housing 1
5P-7305 Engine Turning Tool 1
B 230-6284 Timing Pin (Camshaft) 1
C
136-4632 Timing Pin (Crankshaft) 1
268-1966 Adapter 1
D - Puller (Three Leg) 1
(1)
The Crankshaft Turning Tool is used on the front pulley.
(2)
This Tool is used in the aperture for the electric starting motor.
Start By:
a. Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and
Install".
Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
NOTICE
1/6(W)
w
2020/2/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
Note: Care must be taken in order to ensure that the fuel injection pump timing is not lost during
the removal of the fuel pump gear. Carefully follow the procedure in order to remove the fuel
pump gear.
Illustration 1 g02695977
2/6(W)
w
2020/2/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Illustration 3 g02695996
With Electronic Governor
4/6(W)
w
2020/2/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Illustration 4 g02792627
With Boost Control
1. Remove plug (4) from the cylinder block. Remove O-ring seal (3) from plug (4).
2. Use Tooling (A) in order to rotate the crankshaft so that number one piston is at top dead
center on the compression stroke. Refer to System Operation, Testing and Adjusting,
"Finding Top Center Position for No.1 Piston".
3. Install Tooling (B) through Hole (X) in camshaft gear (1) into the front housing. Use
Tooling (B) in order to lock the camshaft in the correct position.
4. Install Tooling (C) into Hole (Y) in the cylinder block. Use Tooling (C) in order to lock the
crankshaft in the correct position.
Note: Do not use excessive force to install Tooling (C). Do not use Tooling (C) to hold the
crankshaft during repairs.
5. Apply sufficient pressure to fuel injection pump gear (2) in a counterclockwise direction in
order to remove the backlash. Lock fuel injection pump (2) in this position.
In order to lock fuel injection pump (7), loosen locking screw (5) in the fuel injection pump.
Slide spacer (6) into the locked position. Tighten locking screw (5) against the shaft of the
fuel injection pump to a torque of 15 N·m (133 lb in).
5/6(W)
w
2020/2/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Illustration 5 g02697836
6. Mark gear (1), gear (2) and gear (9) in order to show alignment.
Alignment of timing marks
Note: Identification will ensure that the gears can be installed in the original alignment.
7. Loosen nut (8) for the fuel pump gear.
8. Install Tooling (D) through three holes in gear (2). Tighten Tooling (D) until gear (2) is
released.
9. Remove Tooling (D) from gear (2).
10. Remove nut (8) and the washer from fuel pump gear (3). Remove the gear (2).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Feb 24 15:23:23 UTC+0800 2020
6/6(W)
w
2020/2/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D2 EXCAVATOR GBA
Configuration: 320D2 & 320D2 L Excavators GBA00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 (Mech) Engines for Caterpillar Built Machines
Media Number -UENR0674-08 Publication Date -01/06/2015 Date Updated -23/01/2017
i04780456
Fuel Injection Pump Gear - Install
SMCS - 1251-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1)
9U-7336 Crankshaft Turning Tool 1
A(2)
5P-7305 Housing 1
5P-7305 Engine Turning Tool 1
B 230-6284 Timing Pin (Camshaft ) 1
C
136-4632 Timing Pin (Crankshaft) 1
268-1966 Adapter 1
(1)
The Crankshaft Turning Tool is used on the front pulley.
(2)
This Tool is used in the aperture for the electric starting motor.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: The fuel injection pump must remain locked until the procedure instructs you to unlock the
fuel injection pump.
1/8(W)
w
2020/2/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Illustration 1 g02697876
1. If necessary, use Tooling (A) to ensure that number one piston is at top dead center on the
compression stroke. Refer to System Operation, Testing and Adjusting, "Finding Top
Center Position for No.1 Piston".
2. Ensure that Tooling (C) is installed in Hole (Y) in the cylinder block. Use Tooling (C) in
order to lock the crankshaft in the correct position.
2/8(W)
w
2020/2/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Illustration 2 g02697877
3. Ensure that Tooling (B) is installed into Hole (X) in camshaft gear (1).
4. Ensure that shaft (10) of the fuel injection pump is clean and free from damage.
5. Ensure that the fuel injection pump is locked in the correct position. Refer to Disassembly
and Assembly, "Fuel Injection Pump - Install".
6. Ensure that the fuel pump gear is clean and free from wear of damage. If necessary, replace
the fuel pump gear.
3/8(W)
w
2020/2/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Illustration 3 g02698099
7. Install fuel pump gear (2) to shaft (10) of the fuel injection pump. Ensure that the timing
marks on gear (1), gear (2), and gear (9) are in alignment and that the mesh of the gears is
correct.
4/8(W)
w
2020/2/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Illustration 5 g02695996
With Electronic Governor
6/8(W)
w
2020/2/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Illustration 6 g02792627
With Boost Control
8. Install a new spring washer (11) and install nut (8) to shaft (10) of the fuel injection pump.
Apply sufficient pressure to fuel injection pump gear (2) in a counterclockwise direction in
order to remove the backlash. Tighten nut (8) to a torque of 24 N·m (212 lb in).
9. In order to unlock fuel injection pump (7), loosen locking bolt (5) in the fuel injection
pump. Slide spacer (6) into unlock position. Tighten locking bolt (5) against the spacer to a
torque of 12 N·m (106 lb in). The spacer will prevent the locking bolt from tightening
against the shaft of the fuel injection pump.
10. Remove Tooling (B) and Tooling (C).
11. Tighten nut (8) to a torque of 90 N·m (66 lb ft).
12. Ensure that the backlash for gear (1), gear (2) and gear (9) is within specified values. Refer
to the Specifications, "Gear Group (Front)" for further information.
7/8(W)
w
2020/2/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Illustration 7 g02695979
13. Install a new O-ring seal (3) to plug (4). Install plug (4) to the cylinder block. Tighten plug
(4) to a torque of 21 N·m (186 lb in).
14. Lubricate the teeth of the gears with clean engine oil.
End By:
a. Install the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Feb 24 15:24:19 UTC+0800 2020
8/8(W)
w
2020/2/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D2 EXCAVATOR GBA
Configuration: 320D2 & 320D2 L Excavators GBA00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 (Mech) Engines for Caterpillar Built Machines
Media Number -UENR0674-08 Publication Date -01/06/2015 Date Updated -23/01/2017
i07432260
Fuel Injector - Remove
SMCS - 1290-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Laser 4044 Fuel Injector Puller 1
B 422-7170 Capping Kit 1
Start By:
a. Remove the fuel injection lines.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
1/3(W)
w
2020/2/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g06321454
Illustration 2 g06327655
1. Disconnect hose assembly (1) and hose (3) from fuel injector (2).
2. Use Tooling (B) to plug fuel injector (2).
3. Remove bolt (4) and clamp (5) from fuel injector (2).
4. Use Tooling (A) to remove fuel injector (2) from the cylinder head. Remove fuel injector
(2).
5. Remove O-ring seal (6) and seat washer (7) from fuel injector (2).
6. If necessary, repeat Step 1 through Step 5 to remove the remaining fuel injectors.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Mon Feb 24 15:25:14 UTC+0800 2020
2/3(W)
w
2020/2/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D2 EXCAVATOR GBA
Configuration: 320D2 & 320D2 L Excavators GBA00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 (Mech) Engines for Caterpillar Built Machines
Media Number -UENR0674-08 Publication Date -01/06/2015 Date Updated -23/01/2017
i07432337
Fuel Injector - Install
SMCS - 1290-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g06321483
1/2(W)
w
2020/2/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Illustration 2 g06321454
1. Ensure that the seat for fuel injector (2) in the cylinder head and fuel injector (2) is clean
and free from damage.
2. On installing original fuel injector (2), install a new O-ring seal (6) and a new sealing
washer (7) to fuel injector (2).
On installing a new fuel injector, ensure that O-ring seal (6) and sealing washer (7) are not
damaged and are in place.
Note: Do not lubricate the O-ring seal.
3. Position clamp (5) onto fuel injector (2). Install fuel injector (2) into the cylinder head.
Note: Ensure that alignment Pin (8) is located opposite to clamp (5).
4. Install bolt (4) finger tight.
5. Tighten bolt (4) to a torque of 27 N·m (239 lb in).
6. Remove caps from fuel injector (2).
7. Connect hose assembly (1) and hose (3) to fuel injector (2).
8. If necessary, repeat Step 1 through Step 7 to install the remaining fuel injector.
End By:
a. Install the fuel injection lines.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Feb 24 15:26:10 UTC+0800 2020
2/2(W)
w
2020/2/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D2 EXCAVATOR GBA
Configuration: 320D2 & 320D2 L Excavators GBA00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 (Mech) Engines for Caterpillar Built Machines
Media Number -UENR0674-08 Publication Date -01/06/2015 Date Updated -23/01/2017
i04780487
Turbocharger - Remove - Side Mounted Turbocharger
SMCS - 1052-011
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
Note: Plug and cap all open ports and tube assemblies.
1/4(W)
w
2020/2/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Illustration 1 g02719460
1. Loosen hose clamp (2) and disconnect hose assembly (1) from turbocharger (4).
2. Loosen hose clamp (3) and disconnect tube assembly (5) from turbocharger (4).
3. If necessary, remove the hose assembly from the wastegate actuator on the turbocharger.
4. Remove the exhaust out tube assembly from the turbocharger, refer to the Original
Equipment Manufactures (OEM) for the correct procedure.
5. If necessary, remove the exhaust elbow. Refer to Disassembly and Assembly, "Exhaust
Elbow - Remove and Install" for the correct procedure.
2/4(W)
w
2020/2/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Illustration 2 g02719476
6. Remove banjo bolt (7) from tube assembly (10). Remove sealing washers (6) (not shown).
7. Remove bolt (11) from tube assembly (10). Remove tube assembly (10) from turbocharger
(4) and the cylinder block.
8. Remove O-ring seal (12) (not shown) from tube assembly (10).
9. Remove bolts (9) from tube assembly (14). Remove bolts (13) from tube assembly (14).
10. Remove tube assembly (14) from turbocharger (4) and the cylinder block.
11. Remove gasket (8) (not shown) and gasket (15) (not shown).
3/4(W)
w
2020/2/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. Illustration 3 g02719461
12. Remove nuts (18) from turbocharger (4). Remove turbocharger (4) from exhaust manifold
(16).
Note: Ensure that the weight of the turbocharger is supported as the nuts are removed.
13. If necessary, remove studs (17) from exhaust manifold (16).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Feb 24 15:27:06 UTC+0800 2020
4/4(W)
w
2020/2/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D2 EXCAVATOR GBA
Configuration: 320D2 & 320D2 L Excavators GBA00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 (Mech) Engines for Caterpillar Built Machines
Media Number -UENR0674-08 Publication Date -01/06/2015 Date Updated -23/01/2017
i04780488
Turbocharger - Remove - Turbocharger Top Mounted
SMCS - 1052-011
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
Note: Plug and cap all open ports and tube assemblies.
1. Loosen the hose clamps and disconnect the hose assembly from the turbocharger inlet.
2. Loosen the hose clamps and disconnect the hose assembly from the turbocharger outlet.
3. If necessary, remove the hose assembly from the wastegate actuator on the turbocharger.
1/4(W)
w
2020/2/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
26. 4. Remove the exhaust out tube assembly from the turbocharger, refer to the Original
Equipment Manufactures (OEM) for the correct procedure.
5. If necessary, remove the exhaust elbow. Refer to Disassembly and Assembly, "Exhaust
Elbow - Remove and Install" for the correct procedure.
Illustration 1 g02790856
Typical example
6. Remove banjo bolt (1) and remove sealing washers (2) from tube assembly (10).
7. Remove bolts (6) from tube assembly (9). Remove gasket (5).
2/4(W)
w
2020/2/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
27. 8. Remove the tube clamps from tube assembly (9) and tube assembly (10). Position tube
assembly (10) away from turbocharger (4).
9. Remove nuts (3) from turbocharger (4).
10. Remove turbocharger (4) from exhaust manifold (8).
11. If necessary, remove studs (7) from exhaust manifold (8).
Illustration 2 g02790880
Typical example
12. In order to remove tube assembly (9) and tube assembly (10) the removal of exhaust
manifold (8) will be necessary.
13. Remove bolt (13) from tube clips (12) and remove spacer (11).
3/4(W)
w
2020/2/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...