This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D LN excavator with a C6.4 engine. It describes the required tools and safety precautions. The procedure involves using a valve spring compressor tool to compress the springs so the valves can be removed and installed while ensuring the piston is at top dead center. New valve springs must be installed in pairs and all springs on a pair of cylinders must be installed before moving to the next pair.
Caterpillar cat 320 d ln excavator (prefix wbn) service repair manual (wbn000...fkjsekksmem
This document provides the procedure for removing and installing inlet and exhaust valve springs on a Caterpillar 320D LN excavator with a C6.4 engine. It describes using special tools to compress the valve springs and rotate the crankshaft to position the piston for safe removal and installation of the springs. Proper cleaning and inspection of parts is emphasized to prevent damage and wear. The process involves removing keepers and other components to access the springs which must be replaced in matched pairs per cylinder.
Caterpillar cat 320 d l excavator (prefix a9f) service repair manual (a9f0000...fjskekfseik
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. The removal process involves using specialized tools to compress the valve springs so the valves can be serviced while keeping the piston at top dead center. Installation requires cleaning components, lubricating the valves, and using tools to carefully compress the springs into place. Proper assembly procedure and safety precautions are emphasized to avoid injury from released spring forces.
Caterpillar cat 320 d lrr excavator (prefix tae) service repair manual (tae00...fjsekdmmeed
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D LRR excavator engine. It describes using special tools to compress the valve springs, rotate the crankshaft, and remove the springs and related components. The installation section gives steps for cleaning, lubricating, and reinstalling the springs and seals in the proper order. Removal and installation of valve guides is also outlined.
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. Key steps include:
1. Using tooling to compress the valve spring and rotate the crankshaft to allow the piston to hold the valve open while the spring is removed.
2. Removing the valve keepers and spring retainer to access the valve spring.
3. Reversing the process to install new valve springs, making sure to complete installation on pairs of cylinders before moving to the next pair.
Caterpillar cat 320 d l excavator (prefix gdp) service repair manual (gdp0000...fujsekfsmemm
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator. The key steps are:
1. Use valve spring compressor tools to compress the valve spring and remove/install valve keepers and springs while ensuring the piston is at top dead center.
2. Clean and inspect all cylinder head components before installation and replace any worn or damaged parts.
3. Lubricate valve stems before installing valves, springs, retainers and seals in the proper order and orientation using tools as needed.
Caterpillar cat 311 d lrr excavator (prefix lka) service repair manual (lka00...fjsekdmmeed
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C4.2 engine. It describes the required tools and gives step-by-step procedures for removing valve springs safely while ensuring the piston is at top dead center. Proper cleaning and inspection of parts is emphasized. The installation procedure describes compressing the springs, installing new seals, and ensuring correct valve depths are achieved. Safety notices warn of potential injury from compressed springs and ensure springs are replaced in pairs for each cylinder.
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C4.4 engine. The removal procedure involves using specialized tools to compress the valve springs, remove the valve keepers and other components, and extract the valves from the cylinder head. The installation procedure specifies cleaning and inspecting components, lubricating the valve stems, and using tools to compress springs and insert new components in the reverse order of removal. Safety precautions are provided regarding the force of compressed springs. A separate section then details removing and installing the engine oil filter base.
Caterpillar cat 320 e l excavator (prefix tnj) service repair manual (tnj0000...ufjjsjekkeemme
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar 320E L excavator engine. The removal process involves using specialized tools to compress the valve springs and remove the keepers and springs. Installation is the reverse of removal, requiring cleaning, lubricating, and using tools to compress springs during reassembly. Proper torque values are specified for reinstalling components.
Caterpillar cat 320 d ln excavator (prefix wbn) service repair manual (wbn000...fkjsekksmem
This document provides the procedure for removing and installing inlet and exhaust valve springs on a Caterpillar 320D LN excavator with a C6.4 engine. It describes using special tools to compress the valve springs and rotate the crankshaft to position the piston for safe removal and installation of the springs. Proper cleaning and inspection of parts is emphasized to prevent damage and wear. The process involves removing keepers and other components to access the springs which must be replaced in matched pairs per cylinder.
Caterpillar cat 320 d l excavator (prefix a9f) service repair manual (a9f0000...fjskekfseik
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. The removal process involves using specialized tools to compress the valve springs so the valves can be serviced while keeping the piston at top dead center. Installation requires cleaning components, lubricating the valves, and using tools to carefully compress the springs into place. Proper assembly procedure and safety precautions are emphasized to avoid injury from released spring forces.
Caterpillar cat 320 d lrr excavator (prefix tae) service repair manual (tae00...fjsekdmmeed
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D LRR excavator engine. It describes using special tools to compress the valve springs, rotate the crankshaft, and remove the springs and related components. The installation section gives steps for cleaning, lubricating, and reinstalling the springs and seals in the proper order. Removal and installation of valve guides is also outlined.
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. Key steps include:
1. Using tooling to compress the valve spring and rotate the crankshaft to allow the piston to hold the valve open while the spring is removed.
2. Removing the valve keepers and spring retainer to access the valve spring.
3. Reversing the process to install new valve springs, making sure to complete installation on pairs of cylinders before moving to the next pair.
Caterpillar cat 320 d l excavator (prefix gdp) service repair manual (gdp0000...fujsekfsmemm
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator. The key steps are:
1. Use valve spring compressor tools to compress the valve spring and remove/install valve keepers and springs while ensuring the piston is at top dead center.
2. Clean and inspect all cylinder head components before installation and replace any worn or damaged parts.
3. Lubricate valve stems before installing valves, springs, retainers and seals in the proper order and orientation using tools as needed.
Caterpillar cat 311 d lrr excavator (prefix lka) service repair manual (lka00...fjsekdmmeed
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C4.2 engine. It describes the required tools and gives step-by-step procedures for removing valve springs safely while ensuring the piston is at top dead center. Proper cleaning and inspection of parts is emphasized. The installation procedure describes compressing the springs, installing new seals, and ensuring correct valve depths are achieved. Safety notices warn of potential injury from compressed springs and ensure springs are replaced in pairs for each cylinder.
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C4.4 engine. The removal procedure involves using specialized tools to compress the valve springs, remove the valve keepers and other components, and extract the valves from the cylinder head. The installation procedure specifies cleaning and inspecting components, lubricating the valve stems, and using tools to compress springs and insert new components in the reverse order of removal. Safety precautions are provided regarding the force of compressed springs. A separate section then details removing and installing the engine oil filter base.
Caterpillar cat 320 e l excavator (prefix tnj) service repair manual (tnj0000...ufjjsjekkeemme
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar 320E L excavator engine. The removal process involves using specialized tools to compress the valve springs and remove the keepers and springs. Installation is the reverse of removal, requiring cleaning, lubricating, and using tools to compress springs during reassembly. Proper torque values are specified for reinstalling components.
Caterpillar cat 303.5 e2 mini hydraulic excavator (prefix jwy) service repair...fjsjekdmmeme
The document provides instructions for removing and installing inlet and exhaust valves, valve springs, valve guides, and valve seat inserts on a Caterpillar 303.5E2 Mini Hydraulic Excavator engine. The procedures describe using various tools to compress valve springs, remove components in the proper sequence while keeping them clean, and reinstalling components in the reverse order of removal. Special tools and trained personnel are required for some tasks like removing valve guides and seats.
The document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar 320D2 L excavator engine. It describes using a valve spring compressor tool to compress the valve springs before removing the valve keepers and other components. When installing new valves, the instructions specify cleaning and lubricating components, compressing springs with the tool to install keepers, and checking valve depths once installation is complete. Removal and installation of valve guides requires special machinery and trained personnel and includes reaming guides and cutting valve seats after installation.
Caterpillar cat 320 e excavator (prefix aws) service repair manual (aws00001 ...fhhjsjekmdme
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar 320E excavator engine. The summary is:
1. The procedure describes removing the cylinder head and using a valve spring compressor tool to compress the valves springs, remove the keepers, and take out the valves.
2. Reinstallation involves cleaning components, lubricating the valve stems, and using the compressor tool to insert the valves back into the cylinder head and replace the springs and keepers.
3. Proper torque values are provided for reinstalling the cylinder head.
Caterpillar cat 303.5 e2cr mini hydraulic excavator (prefix dwd) service repa...udjjjskkdmme
This document provides instructions for removing and installing inlet and exhaust valve springs on a 303.5E2 CR mini hydraulic excavator. It describes the required tools, safety precautions, and step-by-step procedures for positioning the piston, compressing the valve spring, and removing the valve spring retainer and valve spring. Reinstallation is performed in the reverse order.
Caterpillar cat 320 e excavator (prefix shx) service repair manual (shx00001 ...fhhjsjekmdme
The document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C6.6 engine. The procedure involves using a valve spring compressor tool to compress the valve springs, allowing removal of the valve keepers and springs. Identification marks should be made on the valves and springs. Removal and installation is reversed, with inspection of components and lubrication of valve stems before reinstallation. Safety precautions are noted regarding the force of compressed springs. A similar process is described for removing and installing the engine oil filter base.
Caterpillar cat 416 f backhoe loader (prefix ksf) service repair manual (ksf0...ufusjfjkkekm
This document provides instructions for removing and installing an engine oil cooler on a Caterpillar 416F backhoe loader. The removal procedure involves draining coolant, removing mounting bolts and spacers, and removing the oil cooler assembly. The installation procedure specifies cleaning and inspecting the oil cooler, installing a new gasket, and securing the cooler in place with bolts and spacers. Tools required include wrenches and containers for draining fluids. Safety precautions are provided to contain fluids and follow cleanliness standards when working on engine components.
Caterpillar cat 323 d l excavator (prefix wgc) service repair manual (wgc0000...fjskksmem
This document provides instructions for removing and installing inlet and exhaust valve guides on a Caterpillar C6.4 engine. The procedure involves using specialized tools to remove the valves, electronic unit injectors, and valve guides from the cylinder head. Cleanliness is emphasized to prevent contaminating parts. The installation procedure specifies lubricating valve stems before reinstalling the valves, guides, and other components in the reverse order of removal. Safety notices warn of risks such as being struck by parts or fluids and provide guidance on containment and disposal.
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. The key steps are:
1. Use special tools to compress the valve spring and rotate the crankshaft to allow the piston to hold the valve open while the spring is removed.
2. Remove the valve keepers and spring retainer to access the valve spring.
3. Installation is the reverse of removal, ensuring parts are clean and lubricated before reassembly.
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. The procedure involves using specialty tools to compress the valve springs so that the valves, springs, and related components can be safely accessed and removed or installed one piston at a time. Proper tool use and safety precautions are emphasized to avoid injury from released spring forces.
Caterpillar cat 320 d lrr excavator (prefix tae) service repair manual (tae00...fjjsekkdmme
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D LRR excavator engine. The procedure involves using specialty tools to compress the valve springs so that the valves, springs, and related components can be safely accessed and removed or installed one at a time. Safety precautions are outlined to prevent injury from parts under spring pressure.
Caterpillar cat 320 d l excavator (prefix gdp) service repair manual (gdp0000...fjkskekdmmenm
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator. The summary is:
1. The procedure describes using special tools to compress the valve springs so that the valves, spring retainers, and valve keepers can be safely removed and installed.
2. The process involves rotating the crankshaft to position the piston at top dead center before removing each valve spring to prevent the valve from falling into the cylinder.
3. Reinstallation requires cleaning and inspecting components, lubricating the valves, and using tools to carefully compress the springs squarely during assembly.
Caterpillar cat 320 d ln excavator (prefix gdp) service repair manual (gdp000...fujsekfsmemm
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator. The key steps are:
1. Use valve spring compressor and crankshaft turning tools to compress the valve spring and rotate the piston to access the valve spring.
2. Remove the valve keepers and spring retainer to take off the valve spring.
3. To install, lubricate the valve stem and place the spring and retainer on the cylinder head. Use the compressor to apply pressure and install the keepers.
Caterpillar cat 320 d ln excavator (prefix gdp) service repair manual (gdp000...fjkskekdmmenm
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator. Key steps include:
1. Ensuring the piston is at top dead center to prevent the valve from dropping into the cylinder bore. Compressing the valve spring using a tool and rotating the crankshaft.
2. Removing the valve keepers and spring retainer to access the valve spring. Slowly releasing pressure to remove the spring.
3. Cleaning and lubricating components before installation. Compressing the new spring using a tool and installing the keepers and retainer.
Caterpillar cat 725 c articulated truck (prefix lfb) service repair manual (l...ifse9diodkdk
This document provides instructions for disassembling and assembling the torque converter in a 725C articulated truck. It describes 43 steps to disassemble the various components of the torque converter including removing bolts, seals, bearings, races, and housing pieces. It then lists the required tools and provides a brief assembly procedure, noting to clean all surfaces and apply locking compound or O-ring assembly compound as needed.
Caterpillar cat 329 f l excavator (prefix erl) service repair manual (erl0000...ifse9diodkdk
1. The document provides removal and installation instructions for inlet and exhaust valves on a Caterpillar 329F L Excavator with a C7.1 engine.
2. The procedure involves using special tools to compress the valve springs to remove the valve keepers and other components, and then reversing the process to install new components.
3. Technicians are instructed to clean and inspect all parts, lubricate the valves, and ensure proper valve depth before installing and securing the valve assembly components.
Caterpillar cat 329 el excavator (prefix pty) service repair manual (pty00001...ifse9diodkdk
The document provides instructions for removing and installing the front cover on a Caterpillar 329E excavator engine. The removal procedure involves taking out the crankshaft pulley, fan if equipped, and front seal before removing bolts to take off the front cover. The installation procedure specifies cleaning surfaces, installing a new gasket on guide studs, placing the front cover on with bolts, and using a front cover alignment tool.
Caterpillar cat 329 e excavator (prefix pty) service repair manual (pty00001 ...ifse9diodkdk
The document provides instructions for removing and installing the front cover on a Caterpillar 329E excavator engine. The removal procedure involves taking out the crankshaft pulley, fan if equipped, and front seal before removing bolts to take off the front cover. The installation procedure specifies cleaning surfaces, installing a new gasket on guide studs, placing the front cover on with bolts, and using a front cover alignment tool.
This document provides instructions for removing the engine oil filter base and oil cooler from a Caterpillar 329D LN excavator. The key steps are:
1. Drain engine oil and coolant from the systems before removal to contain fluids.
2. For a remote-mounted filter base, use a strap wrench to remove the oil filter, then remove bolts and the filter base.
3. For an engine-mounted base, drain the cooling system, then remove hoses and bolts to separate the oil cooler from the engine.
Caterpillar cat 329 dl mobile hyd power unit excavator (prefix l5h) service r...ifse9diodkdk
This service repair manual provides instructions for removing and installing various engine components on a Caterpillar 329D L MOBILE HYD POWER UNIT, including:
- Removing and installing inlet and exhaust valve guides from the cylinder head.
- Removing and installing inlet and exhaust valve seat inserts in the cylinder head.
- Removing the engine oil filter base and oil cooler.
- Disassembling the remote or engine mounted engine oil filter base.
The document provides detailed step-by-step instructions, diagrams and safety notices for completing each procedure. Required tools are listed for each job.
Caterpillar cat 329 dl mobile hyd power unit excavator (prefix l5g) service r...ifse9diodkdk
This document provides instructions for disassembling the final drive of a 329D L Mobile Hydraulic Power Unit. It outlines 30 steps to fully disassemble the final drive, including removing gears, carriers, shafts, seals and other components. Various tools are required to secure, lift and remove parts. Cleanliness is important to prevent dirt from entering during disassembly.
Caterpillar cat 329 dl mobile hyd power unit excavator (prefix j9d) service r...ifse9diodkdk
This document provides the disassembly and assembly procedures for a travel motor on a 329DL Mobile Hydraulic Power Unit excavator. The disassembly procedure outlines 28 steps to dismantle the various components of the travel motor. The assembly procedure describes 19 steps to reassemble the travel motor components in reverse order. Proper cleaning and installation of new seals and gaskets is emphasized throughout.
Caterpillar cat 329 dl mobile hyd power unit excavator (prefix j8d) service r...ifse9diodkdk
The document provides instructions for disassembling the final drive of a 329DL Mobile Hydraulic Power Unit. It lists required tools and describes a 37 step process involving removing housing, gears, carriers, shafts, seals, and other components. Cleanliness is important to prevent dirt from entering during reassembly. Weights of removed parts are provided to assist with lifting.
Caterpillar cat 303.5 e2 mini hydraulic excavator (prefix jwy) service repair...fjsjekdmmeme
The document provides instructions for removing and installing inlet and exhaust valves, valve springs, valve guides, and valve seat inserts on a Caterpillar 303.5E2 Mini Hydraulic Excavator engine. The procedures describe using various tools to compress valve springs, remove components in the proper sequence while keeping them clean, and reinstalling components in the reverse order of removal. Special tools and trained personnel are required for some tasks like removing valve guides and seats.
The document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar 320D2 L excavator engine. It describes using a valve spring compressor tool to compress the valve springs before removing the valve keepers and other components. When installing new valves, the instructions specify cleaning and lubricating components, compressing springs with the tool to install keepers, and checking valve depths once installation is complete. Removal and installation of valve guides requires special machinery and trained personnel and includes reaming guides and cutting valve seats after installation.
Caterpillar cat 320 e excavator (prefix aws) service repair manual (aws00001 ...fhhjsjekmdme
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar 320E excavator engine. The summary is:
1. The procedure describes removing the cylinder head and using a valve spring compressor tool to compress the valves springs, remove the keepers, and take out the valves.
2. Reinstallation involves cleaning components, lubricating the valve stems, and using the compressor tool to insert the valves back into the cylinder head and replace the springs and keepers.
3. Proper torque values are provided for reinstalling the cylinder head.
Caterpillar cat 303.5 e2cr mini hydraulic excavator (prefix dwd) service repa...udjjjskkdmme
This document provides instructions for removing and installing inlet and exhaust valve springs on a 303.5E2 CR mini hydraulic excavator. It describes the required tools, safety precautions, and step-by-step procedures for positioning the piston, compressing the valve spring, and removing the valve spring retainer and valve spring. Reinstallation is performed in the reverse order.
Caterpillar cat 320 e excavator (prefix shx) service repair manual (shx00001 ...fhhjsjekmdme
The document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C6.6 engine. The procedure involves using a valve spring compressor tool to compress the valve springs, allowing removal of the valve keepers and springs. Identification marks should be made on the valves and springs. Removal and installation is reversed, with inspection of components and lubrication of valve stems before reinstallation. Safety precautions are noted regarding the force of compressed springs. A similar process is described for removing and installing the engine oil filter base.
Caterpillar cat 416 f backhoe loader (prefix ksf) service repair manual (ksf0...ufusjfjkkekm
This document provides instructions for removing and installing an engine oil cooler on a Caterpillar 416F backhoe loader. The removal procedure involves draining coolant, removing mounting bolts and spacers, and removing the oil cooler assembly. The installation procedure specifies cleaning and inspecting the oil cooler, installing a new gasket, and securing the cooler in place with bolts and spacers. Tools required include wrenches and containers for draining fluids. Safety precautions are provided to contain fluids and follow cleanliness standards when working on engine components.
Caterpillar cat 323 d l excavator (prefix wgc) service repair manual (wgc0000...fjskksmem
This document provides instructions for removing and installing inlet and exhaust valve guides on a Caterpillar C6.4 engine. The procedure involves using specialized tools to remove the valves, electronic unit injectors, and valve guides from the cylinder head. Cleanliness is emphasized to prevent contaminating parts. The installation procedure specifies lubricating valve stems before reinstalling the valves, guides, and other components in the reverse order of removal. Safety notices warn of risks such as being struck by parts or fluids and provide guidance on containment and disposal.
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. The key steps are:
1. Use special tools to compress the valve spring and rotate the crankshaft to allow the piston to hold the valve open while the spring is removed.
2. Remove the valve keepers and spring retainer to access the valve spring.
3. Installation is the reverse of removal, ensuring parts are clean and lubricated before reassembly.
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. The procedure involves using specialty tools to compress the valve springs so that the valves, springs, and related components can be safely accessed and removed or installed one piston at a time. Proper tool use and safety precautions are emphasized to avoid injury from released spring forces.
Caterpillar cat 320 d lrr excavator (prefix tae) service repair manual (tae00...fjjsekkdmme
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D LRR excavator engine. The procedure involves using specialty tools to compress the valve springs so that the valves, springs, and related components can be safely accessed and removed or installed one at a time. Safety precautions are outlined to prevent injury from parts under spring pressure.
Caterpillar cat 320 d l excavator (prefix gdp) service repair manual (gdp0000...fjkskekdmmenm
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator. The summary is:
1. The procedure describes using special tools to compress the valve springs so that the valves, spring retainers, and valve keepers can be safely removed and installed.
2. The process involves rotating the crankshaft to position the piston at top dead center before removing each valve spring to prevent the valve from falling into the cylinder.
3. Reinstallation requires cleaning and inspecting components, lubricating the valves, and using tools to carefully compress the springs squarely during assembly.
Caterpillar cat 320 d ln excavator (prefix gdp) service repair manual (gdp000...fujsekfsmemm
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator. The key steps are:
1. Use valve spring compressor and crankshaft turning tools to compress the valve spring and rotate the piston to access the valve spring.
2. Remove the valve keepers and spring retainer to take off the valve spring.
3. To install, lubricate the valve stem and place the spring and retainer on the cylinder head. Use the compressor to apply pressure and install the keepers.
Caterpillar cat 320 d ln excavator (prefix gdp) service repair manual (gdp000...fjkskekdmmenm
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator. Key steps include:
1. Ensuring the piston is at top dead center to prevent the valve from dropping into the cylinder bore. Compressing the valve spring using a tool and rotating the crankshaft.
2. Removing the valve keepers and spring retainer to access the valve spring. Slowly releasing pressure to remove the spring.
3. Cleaning and lubricating components before installation. Compressing the new spring using a tool and installing the keepers and retainer.
Similar to Caterpillar cat 320 d ln excavator (prefix wbn) service repair manual (wbn00001 and up) (6)
Caterpillar cat 725 c articulated truck (prefix lfb) service repair manual (l...ifse9diodkdk
This document provides instructions for disassembling and assembling the torque converter in a 725C articulated truck. It describes 43 steps to disassemble the various components of the torque converter including removing bolts, seals, bearings, races, and housing pieces. It then lists the required tools and provides a brief assembly procedure, noting to clean all surfaces and apply locking compound or O-ring assembly compound as needed.
Caterpillar cat 329 f l excavator (prefix erl) service repair manual (erl0000...ifse9diodkdk
1. The document provides removal and installation instructions for inlet and exhaust valves on a Caterpillar 329F L Excavator with a C7.1 engine.
2. The procedure involves using special tools to compress the valve springs to remove the valve keepers and other components, and then reversing the process to install new components.
3. Technicians are instructed to clean and inspect all parts, lubricate the valves, and ensure proper valve depth before installing and securing the valve assembly components.
Caterpillar cat 329 el excavator (prefix pty) service repair manual (pty00001...ifse9diodkdk
The document provides instructions for removing and installing the front cover on a Caterpillar 329E excavator engine. The removal procedure involves taking out the crankshaft pulley, fan if equipped, and front seal before removing bolts to take off the front cover. The installation procedure specifies cleaning surfaces, installing a new gasket on guide studs, placing the front cover on with bolts, and using a front cover alignment tool.
Caterpillar cat 329 e excavator (prefix pty) service repair manual (pty00001 ...ifse9diodkdk
The document provides instructions for removing and installing the front cover on a Caterpillar 329E excavator engine. The removal procedure involves taking out the crankshaft pulley, fan if equipped, and front seal before removing bolts to take off the front cover. The installation procedure specifies cleaning surfaces, installing a new gasket on guide studs, placing the front cover on with bolts, and using a front cover alignment tool.
This document provides instructions for removing the engine oil filter base and oil cooler from a Caterpillar 329D LN excavator. The key steps are:
1. Drain engine oil and coolant from the systems before removal to contain fluids.
2. For a remote-mounted filter base, use a strap wrench to remove the oil filter, then remove bolts and the filter base.
3. For an engine-mounted base, drain the cooling system, then remove hoses and bolts to separate the oil cooler from the engine.
Caterpillar cat 329 dl mobile hyd power unit excavator (prefix l5h) service r...ifse9diodkdk
This service repair manual provides instructions for removing and installing various engine components on a Caterpillar 329D L MOBILE HYD POWER UNIT, including:
- Removing and installing inlet and exhaust valve guides from the cylinder head.
- Removing and installing inlet and exhaust valve seat inserts in the cylinder head.
- Removing the engine oil filter base and oil cooler.
- Disassembling the remote or engine mounted engine oil filter base.
The document provides detailed step-by-step instructions, diagrams and safety notices for completing each procedure. Required tools are listed for each job.
Caterpillar cat 329 dl mobile hyd power unit excavator (prefix l5g) service r...ifse9diodkdk
This document provides instructions for disassembling the final drive of a 329D L Mobile Hydraulic Power Unit. It outlines 30 steps to fully disassemble the final drive, including removing gears, carriers, shafts, seals and other components. Various tools are required to secure, lift and remove parts. Cleanliness is important to prevent dirt from entering during disassembly.
Caterpillar cat 329 dl mobile hyd power unit excavator (prefix j9d) service r...ifse9diodkdk
This document provides the disassembly and assembly procedures for a travel motor on a 329DL Mobile Hydraulic Power Unit excavator. The disassembly procedure outlines 28 steps to dismantle the various components of the travel motor. The assembly procedure describes 19 steps to reassemble the travel motor components in reverse order. Proper cleaning and installation of new seals and gaskets is emphasized throughout.
Caterpillar cat 329 dl mobile hyd power unit excavator (prefix j8d) service r...ifse9diodkdk
The document provides instructions for disassembling the final drive of a 329DL Mobile Hydraulic Power Unit. It lists required tools and describes a 37 step process involving removing housing, gears, carriers, shafts, seals, and other components. Cleanliness is important to prevent dirt from entering during reassembly. Weights of removed parts are provided to assist with lifting.
This document provides instructions for removing the engine oil filter base and oil cooler from a Caterpillar 329D LN excavator. The key steps are:
1. Drain engine oil and coolant from the systems before removal to contain fluids.
2. For a remote-mounted filter base, use a strap wrench to remove the oil filter, then remove bolts and the filter base.
3. For an engine-mounted base, drain the cooling system, then remove hoses and bolts to separate the oil cooler from the engine.
This document provides instructions for disassembling the final drive on a Caterpillar 329D2 L excavator. The process involves:
1. Removing the final drive and separating it from the track assembly and travel motor.
2. Lifting the final drive and disassembling it into components like the cover, carrier assembly, ring gears, and main housing.
3. Using tools like pins, screws, and lifting devices to separate individual parts which are then cleaned and inspected.
4. Disassembling internal components of the carrier assembly like planetary gears and shafts.
The instructions describe each step in detail and include illustrations of the components and proper tooling to use. Safety notes are included about handling
This document provides instructions for removing the rear power take-off (RPTO) from a C7.1 engine. It outlines 10 steps to remove gears, adapters, seals and other components from the flywheel housing. Precautions are given to keep parts clean and ensure correct alignment of sleeves and oil holes. Required tools include a driver group. The process is reversed to install the RPTO following similar steps and precautions.
This document provides instructions for removing and installing a crankshaft from a C7.1 engine. It describes removing components like the front housing, oil pump, seals and bearings. It then instructs how to attach lifting slings to the crankshaft and remove it from the engine block. Detailed steps are provided for cleaning and inspecting the crankshaft and installing new bearings, thrust washers and seals before reinstalling the crankshaft and torquing the bolts to the specified values. Clear illustrations supplement the text instructions.
Caterpillar cat 329 d2 l excavator (prefix tmj) service repair manual (tmj000...ifse9diodkdk
The document provides instructions for removing and installing the engine oil pump on a Caterpillar C7.1 engine. It describes removing the oil pan, bolts and brackets holding the pump. It also details checking clearances after installation and installing the oil pan. Installation involves cleaning components, installing dowels and bolts, and checking gear backlash.
This document provides instructions for installing an engine oil pump on a C7.1 engine. It describes cleaning and inspecting the oil pump components and installing the cross over tube assembly with new gaskets. It also details reassembling the oil pump if disassembled, ensuring proper dowel pin locations, and installing the oil pump assembly onto the cylinder block and torquing the bolts. The installation is completed by installing a new gasket and the suction pipe.
This document provides instructions for removing the rear power take-off (RPTO) from a C7.1 engine. It outlines 10 steps to remove gears, hubs, adapters and other components from the flywheel housing. Precautions are given to keep parts clean and ensure correct alignment of sleeves and oil holes. Required tools include a driver group. The process concludes by removing the flywheel after the RPTO is disassembled.
Caterpillar cat 329 d ln excavator (prefix ebm) service repair manual (ebm000...ifse9diodkdk
The document provides instructions for removing and installing pistons and connecting rods on a Caterpillar C7 engine. It describes removing the cylinder head, oil pump, and piston cooling jets before removing each piston and connecting rod assembly. The connecting rod cap and bearings are removed, then the piston and connecting rod are separated. Reinstallation follows the reverse order, applying anti-seize compound and using tools to properly position the piston rings and install the connecting rod bearings.
Caterpillar cat 329 d l excavator (prefix yfw) service repair manual (yfw0000...ifse9diodkdk
This document provides instructions for disassembling and assembling the final drive of a 329D or 329D L excavator. It lists 37 steps for disassembly, removing components like gears, shafts, carriers and seals. It then lists 21 steps for assembly, providing details on cleaning parts, applying lubricants, setting bearing preloads using presses and shims, and installing seals and gears back into their original locations and orientations. Cleanliness is emphasized as important throughout the process.
Caterpillar cat 329 d l excavator (prefix ebm) service repair manual (ebm0000...ifse9diodkdk
This document provides instructions for removing and installing various engine components on a Caterpillar 329D L and 329D LN excavator, including:
- Removing and installing the engine oil pan, which involves draining the oil, removing bolts and the pan, cleaning surfaces, applying sealant, and reinstalling with new bolts and gasket.
- Removing and installing piston cooling jets by removing and replacing bolts to hold the jets in place.
- Procedures for removing pistons and connecting rods by identifying parts, removing caps and bolts, and pushing components out of the engine block.
Caterpillar cat 329 d excavator (prefix yfw) service repair manual (yfw00001 ...ifse9diodkdk
This document provides instructions for disassembling and assembling the final drive of a 329D or 329D L excavator. It lists 37 steps for disassembly, removing components like gears, shafts, bearings and seals. The assembly section outlines 15 steps, including pressing bearings into place, installing seals, and using shims to set the proper bearing preload when mounting the main housing onto the motor housing. Cleanliness is emphasized throughout as important for preventing contamination.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
Real-time driver monitoring is one of the easiest ways to make fleet management efficient as well as seamless. Connected vehicle solutions such as fleet GPS trackers and associated software help businesses in several ways. Refer to the post below for more details.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D LN EXCAVATOR WBN
Configuration: 320D LN Excavator WBN00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02747674
Inlet and Exhaust Valve Springs - Remove and Install
SMCS - 1108-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6195 Valve Spring Compressor 1
B 9U-6198 Crankshaft Turning Tool 1
Start By:
a. Remove the rocker shaft assembly. Refer to Disassembly and Assembly, "Rocker Shaft and
Pushrod - Remove".
b. Remove the valve mechanism cover base. Refer to Disassembly and Assembly, "Valve
Mechanism Cover Base - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: The following procedure should be adopted in order to remove the valve springs when the
cylinder head is installed to the engine.
1/6(W)
w
2020/2/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Note: Ensure that the appropriate piston is at top dead center before the valve spring is removed.
Failure to ensure that the piston is at top dead center may allow the valve to drop into the cylinder
bore.
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
NOTICE
Plug the apertures for the push rods in the cylinder head in order to
prevent the entry of loose parts into the engine.
Illustration 1 g01376301
2/6(W)
w
2020/2/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. Illustration 2 g01376302
NOTICE
Ensure that the valve spring is compressed squarely or damage to the
valve stem may occur.
1. Install Tooling (A) into position on the cylinder head in order to compress a valve spring (4)
for the appropriate piston.
2. Use Tooling (A) in order to compress valve spring (4) and open valve (1) slightly.
Note: Do not compress valve spring (4) so that valve spring retainer (3) touches valve stem
seal (5).
3. Use Tooling (B) in order to rotate the crankshaft carefully, until the piston touches the
valve.
Note: Do not use excessive force to turn the crankshaft. The use of force can result in bent
valve stems.
4. Continue to rotate the crankshaft and gradually release the pressure on Tooling (A) until the
piston is at the top dead center position. The valve is now held in a position that allows
valve spring (4) to be safely removed.
Note: Valve springs must be replaced in pairs for the inlet valve or the exhaust valve of
each cylinder. If all valve springs require replacement the procedure can be carried out on
two cylinders at the same time. The procedure can be carried out on the following pairs of
cylinders. 1 with 6, 2 with 5 and 3 with 4. Ensure that all of the valve springs are installed
before changing from one pair of cylinders to another pair of cylinders.
3/6(W)
w
2020/2/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. NOTICE
Do not turn the crankshaft while the valve springs are removed.
5. Apply sufficient pressure to Tooling (A) in order to allow removal of valve keepers (2).
Note: Do not compress valve spring (4) so that valve spring retainer (3) touches valve stem
seal (5).
Remove valve keepers (2).
6. Slowly release the pressure on Tooling (A).
7. Remove valve spring retainer (3) and remove valve spring (4).
8. If necessary, remove valve stem seals (5).
9. Remove Tooling (A).
Note: The installation of each set of valve springs (4) must be completed before attempting to
remove the next set of valve springs (4).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 9U-6195 Valve Spring Compressor 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
4/6(W)
w
2020/2/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Illustration 3 g01376913
Illustration 4 g01376302
1. The outer face of the valve guides must be clean and dry before installing the valve stem
seal (5). Install new valve stem seal (5) onto the valve guide.
2. Install valve spring (4) onto the cylinder head. Position valve spring retainer (3) on valve
spring (4).
3. Install Tooling (A) in the appropriate position on the cylinder head in order to compress
valve spring (4).
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
5/6(W)
w
2020/2/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. 4. Apply sufficient pressure to Tooling (A) in order to install valve keepers (2). Do not
compress valve spring (4) so that valve spring retainer (3) touches valve stem seal (5).
5. Carefully release the pressure on Tooling (A).
End By:
a. Install the valve mechanism cover base. Refer to Disassembly and Assembly, "Valve
Mechanism Cover Base - Remove and Install".
b. Install the rocker shaft assembly. Refer to Disassembly and Assembly, "Rocker Shaft and
Pushrod - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Feb 10 21:05:56 UTC+0800 2020
6/6(W)
w
2020/2/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D LN EXCAVATOR WBN
Configuration: 320D LN Excavator WBN00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i06051426
Inlet and Exhaust Valves - Remove and Install
SMCS - 1105-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8S-6691 Cylinder Head Repair Stand 1
B 9U-6195 Valve Spring Compressor Gp 1
C 5P-1720 Seal Pick 1
Start By:
a. Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Note the location and orientation of all components for assembly purposes.
1. Clean the bottom face of the cylinder head. Check the depth of the valves below the face of
the cylinder head before the valve springs are removed. Refer to Specifications, "Cylinder
Head Valves" for the correct dimensions.
1/6(W)
w
2020/2/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. 2. Place a temporary identification mark on the heads of the valves in order to identify the
correct position.
Illustration 1 g01376164
3. Use a suitable lifting device in order to position cylinder head (1) onto Tooling (A) with the
valve springs upward. The weight of cylinder head (1) is approximately 113 kg (250 lb).
Note: Ensure that cylinder head (1) is kept on a clean, soft surface in order to prevent
damage to the machined face.
Illustration 2 g01376174
2/6(W)
w
2020/2/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Illustration 3 g01376184
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
4. Install Tooling (B) on cylinder head (1) in order to compress valve spring (5).
NOTICE
Ensure that the valve spring is compressed squarely or damage to the
valve stem may occur.
5. Apply sufficient pressure to Tooling (B) in order to remove valve keepers (3). Do not
compress the spring so that valve spring retainer (4) touches valve stem seal (6).
6. Slowly release the pressure on Tooling (B).
7. Remove valve spring retainer (4). Remove valve spring (5). Remove valve (2).
8. Use Tooling (C) in order to remove valve stem seal (6).
3/6(W)
w
2020/2/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. 9. Repeat Steps 4 through 7 for the remaining valves.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 8S-6691 Cylinder Head Repair Stand 1
B 9U-6195 Valve Spring Compressor Gp 1
D 312-8755 Valve Stem Seal Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean all components of the cylinder head assembly. Ensure that all ports, all coolant
passages, and all lubrication passages in the cylinder head are free from debris. Follow
Steps 1.a through 1.d in order to inspect the components of the cylinder head assembly.
Replace any components that are worn or damaged.
a. Inspect the cylinder head for wear and for damage. Refer to Testing and Adjusting,
"Cylinder Head Inspect".
b. Inspect the valve seats for wear and for damage. Refer to Specifications, "Cylinder
Head Valves" for further information.
c. Inspect the valve guides for wear and for damage. Refer to Specifications, "Cylinder
Head Valves" and Testing and Adjusting, "Valve Guide - Inspect" for further
information.
d. Inspect the valves for wear and for damage. Refer to Specifications, "Cylinder Head
Valves ".
e. Inspect valve springs (5) for damage and for the correct length. Refer to
Specifications, "Cylinder Head Valves ".
4/6(W)
w
2020/2/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Illustration 4 g01376184
Illustration 5 g01376926
2. Lubricate the stem of valve (2) with clean engine oil. Install valve (2) in the appropriate
position in the cylinder head.
3. The outer face of the valve guides must be clean and dry before installing the valve stem
seal (6). Use Tooling (C) in order to install new valve stem seal (6) onto the valve guide.
4. Install valve spring (5) onto the cylinder head. Position valve spring retainer (4) on valve
spring (5).
5. Install Tooling (B) in the appropriate position on cylinder head (1) in order to compress
valve spring (5).
Improper assembly of parts that are spring loaded can cause bodily
injury.
5/6(W)
w
2020/2/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
6. Apply sufficient pressure to Tooling (B) in order to install valve keepers (3). Do not
compress spring (5) so that valve spring retainer (4) touches valve stem seal (6).
7. Carefully release the pressure on Tooling (B).
8. Repeat Steps 2 through 7 for the remaining valves.
End By:
a. Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Feb 10 21:06:52 UTC+0800 2020
6/6(W)
w
2020/2/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D LN EXCAVATOR WBN
Configuration: 320D LN Excavator WBN00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i04625003
Inlet and Exhaust Valve Guides - Remove and Install
SMCS - 1104-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 384-8861 Valve Guide Remover 1
B 138-7573 Link Bracket 4
C 1U-9200 Lever Puller Hoist 1
D 8S-6691 Cylinder Head Repair Stand 1
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
B. Remove the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injector - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4(W)
w
2020/2/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: Refer to Special Instructions, SMHS7953-00, "Use of Valve Seat Insert Puller Group" to
aid with the removal of the inlet and exhaust valve seats.
Illustration 1 g01377064
1. Attach Tooling (B) , Tooling (C) , and a suitable lifting device to cylinder head (1) . Use
Tooling (B) , Tooling (C) , and the suitable lifting device in order to turn over cylinder head
(1) by 180° onto Tooling (D) .
2/4(W)
w
2020/2/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Illustration 2 g01377121
2. Use Tooling (A) in order to remove valve guides (2) (not shown).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
E 384-8862 Valve Guide Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
3/4(W)
w
2020/2/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Illustration 3 g01377130
1. Lubricate the outside of valve guides (2) (not shown) with clean engine oil.
2. Use Tooling (E) in order to install new valve guides (2) . Install valve guide (2) so that
valve guide (2) protrudes 16.000 mm (0.6299 inch) above Surface (X) of cylinder head (1) .
End By:
a. Install the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injector - Install".
b. Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and Exhaust
Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Feb 10 21:07:48 UTC+0800 2020
4/4(W)
w
2020/2/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D LN EXCAVATOR WBN
Configuration: 320D LN Excavator WBN00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i04625001
Inlet and Exhaust Valve Seat Inserts - Remove and Install
SMCS - 1103-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
166-7441 Valve Seat Extractor Tool 1
6V-4194 Valve Seat Extractor (1)
1
6V-4196 Valve Seat Extractor (1)
1
B 138-7573 Link Bracket 4
C 1U-9200 Lever Puller Hoist 1
D 8S-6691 Cylinder Head Repair Stand 1
( 1 )
Component of the Valve Seat Extractor Tool Group.
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
B. Remove the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injectors - Remove".
NOTICE
Keep all parts clean from contaminants.
1/5(W)
w
2020/2/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Contaminants may cause rapid wear and shortened component life.
Note: Refer to Special Instructions, SMHS7953-00, "Use of Valve Seat Insert Puller Group" to
aid with the removal of the inlet and exhaust valve seats.
Illustration 1 g01377064
1. Attach Tooling (B ) , Tooling (C) , and a suitable lifting device to cylinder head (1) . Use
Tooling (B ) , Tooling (C) , and the suitable lifting device in order to turn over cylinder head
(1) by 180° onto Tooling (D) .
2/5(W)
w
2020/2/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Illustration 2 g01376571
2. Use the valve seat grinder of Tooling (A) in order to notch the valve seat.
Illustration 3 g01376578
3. Use the valve seat extractor of Tooling (A) to remove the inlet and exhaust valve seats.
4. Clean the valve seat in the cylinder head. Remove any rough areas from the valve seat in the
cylinder head.
5. Repeat Steps 2 through 4 for the remaining inlet valve seat inserts and exhaust valve seat
inserts.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
E 384-8859 Valve Seat Installer 1
F 384-8860 Valve Seat Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
3/5(W)
w
2020/2/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Illustration 4 g01377071
Typical Example
1. Lower the temperature of the new inlet valve seat inserts (2) . Use Tooling (E) in order to
install a new inlet valve seat insert (2) (not shown) in the cylinder head.
Illustration 5 g01376588
Typical Example
2. Lower the temperature of new exhaust valve seat inserts (3) . Use Tooling (E) and Tooling
(F) in order to install the new exhaust valve seat insert (3) (not shown) in the cylinder head.
Note: The temperature of exhaust valve seat insert (3) is lowered in order to ease the
installation of exhaust valve seat insert (3) .
3. Repeat Step 1 and 2 for the remaining inlet valve seat inserts and exhaust valve seat inserts.
End By:
a. Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and Exhaust
Valves - Remove and Install".
b. Install the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injectors - Install".
4/5(W)
w
2020/2/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D LN EXCAVATOR WBN
Configuration: 320D LN Excavator WBN00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02746253
Engine Oil Cooler - Remove
SMCS - 1378-011
Removal Procedure
Start By:
a. Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump
- Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/2(W)
w
2020/2/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. Illustration 1 g01375410
1. Disconnect harness assembly (1).
2. Remove bolts (2) and remove engine oil cooler (3). Remove gasket (4) (not shown) from the
engine cylinder block.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Feb 10 21:09:39 UTC+0800 2020
2/2(W)
w
2020/2/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D LN EXCAVATOR WBN
Configuration: 320D LN Excavator WBN00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02746254
Engine Oil Cooler - Disassemble
SMCS - 1378-015
Disassembly Procedure
Start By:
a. Remove the engine oil cooler. Refer to Disassembly and Assembly, "Engine Oil Cooler - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior of the
components should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism. Precision components can be damaged by contaminants or by dirt. Perform disassembly
procedures on a clean work surface. Keep components covered and protected at all times.
1/2(W)
w
2020/2/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...