This document provides instructions for removing and installing a boom cylinder on a 320D excavator. It includes:
1) Detailed steps to remove the boom cylinder such as releasing hydraulic pressure, removing mounting bolts and pins, and lifting the cylinder off the machine.
2) Information on required tools and torque specifications for reassembly.
3) The installation procedure which describes mounting the cylinder back onto the excavator and reinstalling all mounting hardware.
Safety warnings are provided to relieve hydraulic pressure before disassembling cylinders. The document contains diagrams illustrating each step in the process.
This document provides instructions for installing a flywheel and removing and installing a wet back end flywheel housing on a Caterpillar 320 GC excavator. It describes using guide studs and lifting devices to position the heavy flywheel and housing. Torque specifications and tightening sequences are given for installing mounting bolts. Replacing seals, gaskets and dowels is also covered.
Caterpillar cat 305 e2cr mini hydraulic excavator (prefix pyr) service repair...fjskekfseik
The document provides instructions for removing and installing various engine components on a Caterpillar 305E2 CR mini hydraulic excavator powered by a C2.4 engine, including:
- Removing and installing the idler gear.
- Removing and installing the front housing.
- Removing and installing the valve mechanism cover.
- Removing and installing the rocker shaft and push rods.
- Disassembling and assembling the rocker shaft.
The procedures include lists of required tools and step-by-step instructions with illustrations. Safety notices are also provided regarding keeping parts clean and preventing injury from spring-loaded components.
Caterpillar cat 301.7 cr mini hydraulic excavator (prefix jh7) service repair...fjsjekdmmeme
The document provides instructions for disassembling and assembling the boom cylinder of a Caterpillar 301.7CR Mini Hydraulic Excavator. The disassembly procedure involves removing seals and internal components from both ends of the cylinder. The assembly procedure describes installing these components in reverse order. Separate sections also describe removing and installing the entire boom and boom swing cylinder. Safety precautions are provided regarding hydraulic pressure during maintenance.
Caterpillar cat 305 cr mini hydraulic excavator (prefix dgt) service repair m...fjskekfseik
The document provides instructions for removing the swivel on a 305CR Mini Hydraulic Excavator. It lists the required tools and notes to release hydraulic pressure and remove the cab first. The procedure involves using plugs and caps to seal ports while removing 4 bolts to detach the swivel assembly.
Caterpillar cat 320 d l excavator (prefix dhk) service repair manual (dhk0000...fkjsekksmem
This document provides instructions for removing and installing the boom cylinder on a 320D and 320D L excavator. It outlines the required tools and safety precautions. The removal process involves releasing hydraulic pressure, removing attachment points, and lifting the cylinder out of place. Reinstallation is the reverse of removal. Torque specifications are provided for correct assembly.
Caterpillar cat 305 e2 cr mini hydraulic excavator (prefix df5) service repai...fjskekfseik
The document provides instructions for removing and installing various components of a 305E2 CR Mini Hydraulic Excavator engine, including the fuel injection lines, exhaust gas recirculation cooler, fuel injection pump, electronic unit injector, and turbocharger. Safety precautions are outlined that must be followed when working on fuel system and high temperature components.
Caterpillar cat 320 l track type excavator (prefix 2dl) service repair manual...fkjsekksmem
This document provides instructions for servicing components of Caterpillar excavator models 320, 320L, and 320N, including:
- Removing and installing inlet and exhaust valve seals
- Removing the engine oil filter base
- Installing the engine oil filter base
- Removing the engine oil cooler
- Disassembling the engine oil cooler
- Reassembling the engine oil cooler
- Installing the engine oil cooler
The document includes diagrams and step-by-step instructions for maintenance procedures. Technicians are advised to keep components clean and contain fluids properly during repair.
Caterpillar cat 320 d l excavator (prefix a9f) service repair manual (a9f0000...fjskekfseik
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. The removal process involves using specialized tools to compress the valve springs so the valves can be serviced while keeping the piston at top dead center. Installation requires cleaning components, lubricating the valves, and using tools to carefully compress the springs into place. Proper assembly procedure and safety precautions are emphasized to avoid injury from released spring forces.
This document provides instructions for installing a flywheel and removing and installing a wet back end flywheel housing on a Caterpillar 320 GC excavator. It describes using guide studs and lifting devices to position the heavy flywheel and housing. Torque specifications and tightening sequences are given for installing mounting bolts. Replacing seals, gaskets and dowels is also covered.
Caterpillar cat 305 e2cr mini hydraulic excavator (prefix pyr) service repair...fjskekfseik
The document provides instructions for removing and installing various engine components on a Caterpillar 305E2 CR mini hydraulic excavator powered by a C2.4 engine, including:
- Removing and installing the idler gear.
- Removing and installing the front housing.
- Removing and installing the valve mechanism cover.
- Removing and installing the rocker shaft and push rods.
- Disassembling and assembling the rocker shaft.
The procedures include lists of required tools and step-by-step instructions with illustrations. Safety notices are also provided regarding keeping parts clean and preventing injury from spring-loaded components.
Caterpillar cat 301.7 cr mini hydraulic excavator (prefix jh7) service repair...fjsjekdmmeme
The document provides instructions for disassembling and assembling the boom cylinder of a Caterpillar 301.7CR Mini Hydraulic Excavator. The disassembly procedure involves removing seals and internal components from both ends of the cylinder. The assembly procedure describes installing these components in reverse order. Separate sections also describe removing and installing the entire boom and boom swing cylinder. Safety precautions are provided regarding hydraulic pressure during maintenance.
Caterpillar cat 305 cr mini hydraulic excavator (prefix dgt) service repair m...fjskekfseik
The document provides instructions for removing the swivel on a 305CR Mini Hydraulic Excavator. It lists the required tools and notes to release hydraulic pressure and remove the cab first. The procedure involves using plugs and caps to seal ports while removing 4 bolts to detach the swivel assembly.
Caterpillar cat 320 d l excavator (prefix dhk) service repair manual (dhk0000...fkjsekksmem
This document provides instructions for removing and installing the boom cylinder on a 320D and 320D L excavator. It outlines the required tools and safety precautions. The removal process involves releasing hydraulic pressure, removing attachment points, and lifting the cylinder out of place. Reinstallation is the reverse of removal. Torque specifications are provided for correct assembly.
Caterpillar cat 305 e2 cr mini hydraulic excavator (prefix df5) service repai...fjskekfseik
The document provides instructions for removing and installing various components of a 305E2 CR Mini Hydraulic Excavator engine, including the fuel injection lines, exhaust gas recirculation cooler, fuel injection pump, electronic unit injector, and turbocharger. Safety precautions are outlined that must be followed when working on fuel system and high temperature components.
Caterpillar cat 320 l track type excavator (prefix 2dl) service repair manual...fkjsekksmem
This document provides instructions for servicing components of Caterpillar excavator models 320, 320L, and 320N, including:
- Removing and installing inlet and exhaust valve seals
- Removing the engine oil filter base
- Installing the engine oil filter base
- Removing the engine oil cooler
- Disassembling the engine oil cooler
- Reassembling the engine oil cooler
- Installing the engine oil cooler
The document includes diagrams and step-by-step instructions for maintenance procedures. Technicians are advised to keep components clean and contain fluids properly during repair.
Caterpillar cat 320 d l excavator (prefix a9f) service repair manual (a9f0000...fjskekfseik
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. The removal process involves using specialized tools to compress the valve springs so the valves can be serviced while keeping the piston at top dead center. Installation requires cleaning components, lubricating the valves, and using tools to carefully compress the springs into place. Proper assembly procedure and safety precautions are emphasized to avoid injury from released spring forces.
Caterpillar cat 301.8 mini hydraulic excavator (prefix h8 x) service repair m...fjsjekdmmeme
The documents provide instructions for removing and installing various components on a 301.8 Mini Hydraulic Excavator, including the blade, bucket, bucket linkage, and bucket cylinder. The procedures describe disconnecting hoses, removing bolts and pins, lifting components, and installing components in the reverse order of removal. Safety precautions are provided, such as relieving system pressure before disassembling cylinders.
The document provides assembly instructions for installing a swing gear and bearing on an excavator. It lists required tools and parts. The procedure involves cleaning the swing gear and bearing, applying lubricant and sealant, lifting it into position using links, and securing it with bolts torqued to specification. Inner and outer dust seals are installed in seal grooves before completing reassembly of the undercarriage frame.
Caterpillar cat 311 b track type excavator (prefix 2ls) service repair manual...fjskefkemms
This document provides instructions for servicing components of a 311B excavator engine, including:
1) Instructions for assembling the rocker shaft, including the components and installation steps.
2) Instructions for installing the rocker shaft and pushrods, including torque specifications.
3) Instructions for removing the cylinder head, including removal steps and safety notices.
Caterpillar cat 303.5 c cr mini hydraulic excavator (prefix dmy) service repa...fjsjekdmmeme
The document provides instructions for disassembling and inspecting various engine components of a 303.5C Mini Hydraulic Excavator, including the timing gear, camshaft, oil pan, piston, connecting rod, crankshaft, and cylinder block. It lists the components in their order of disassembly and provides illustrations showing how to remove each part. Specifications for measuring component wear limits are also provided to determine if parts need replacing. Safety notes are included throughout to warn of potential dangers during disassembly.
Caterpillar cat c2.2 industrial engine (prefix g7 m) service repair manual (g...ifkkdmdmdm
The document provides instructions for removing and installing the crankshaft pulley and front seal on an industrial engine. It describes removing the pulley by drilling holes in the seal, inserting a puller tool, and removing the woodruff key from the crankshaft. For installation, it instructs to clean components, insert the key, lubricate parts, and tighten the pulley nut to the specified torque. It also describes removing the front housing by removing mounting nuts and identifying locating features.
Caterpillar cat 311 c excavator (prefix cke) service repair manual (cke00001 ...fjskefkemms
This service repair manual provides instructions for removing and installing inlet and exhaust valve seals on models 311C and 311C U excavators. The procedures describe using a seal pick tool to remove old seals from valve guides and installing new seals. Safety notices are included to keep parts clean and contain fluids.
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 320 excavator models. It describes the required tools and gives a step-by-step process including removing clips and pins, sliding tubes, and removing/installing parts like the governor, linkage, and seals using special tools. References are provided for more information on governors and linkage inspection procedures.
Caterpillar cat 320 d l excavator (prefix kzf) service repair manual (kzf0000...fkjsekksmem
The document provides instructions for disassembling and assembling a final drive for excavator models 320D and 320D L. It describes 33 steps to disassemble the final drive components including removing bolts, shafts, gears, seals, and bearings. It then describes 32 steps for reassembling the final drive, applying sealant and lubricant, and installing components in reverse order using pressing and lifting tools. Precision is required to determine shim thickness for proper bearing preload.
Caterpillar cat m316 d wheeled excavator (prefix w6a) service repair manual (...fujsjefjwerkskemm
This document provides instructions for removing and installing an idler gear on a Caterpillar C6.6 engine. It describes the required tools and steps to:
1) Lock the camshaft and crankshaft in position, remove bolts, and remove the standard or heavy-duty idler gear.
2) Clean and inspect the idler gear components, install the idler gear while aligning timing marks, install bolts, and check end play and backlash.
3) Ensure the number one piston is at top dead center before installing the idler gear in the correct position and alignment.
Caterpillar cat 304.5 e mini hydraulic excavator (prefix fxt) service repair ...fjskekfseik
The document provides instructions for removing and installing piston and connecting rod assemblies in an engine. Key steps include:
1. Removing the cylinder head and oil pan before removing the piston and connecting rod.
2. Pushing the connecting rod and piston out of the cylinder block after removing the connecting rod cap and bearings.
3. Reversing the removal procedures to install the piston and connecting rod assemblies, ensuring correct orientation and applying lubricant to moving parts.
Caterpillar cat 305 cr mini hydraulic excavator (prefix dsa) service repair m...fjskekfseik
The document provides instructions for removing and disassembling the travel motor from a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing the track and final drive sprocket. Disassembly involves marking parts, draining oil, removing plates, barrels and pistons. Multiple gears, shafts, seals and other internal components are then dismantled from the travel motor housing.
Caterpillar cat 16 h na motor grader (prefix 6zj) service repair manual (6zj0...fjskefkemms
This document provides instructions for removing and installing various engine components on a 16H NA Motor Grader with a 3406C engine, including:
1. Timing gears and plate removal and installation.
2. Camshaft removal and installation.
3. Camshaft bearing removal and installation.
4. Connecting rod bearing removal and installation.
5. Crankshaft main bearing removal and installation.
The instructions describe the individual steps for removing and installing each component, including the use of any necessary tools. Safety notices and additional notes are also provided throughout.
Caterpillar cat 330 track type excavator (prefix 6 wj) service repair manual ...fjskefkemms
This document provides instructions for removing and installing travel motors on 330 and 330L excavator models. It describes:
- Releasing hydraulic pressure before removing components
- Removing covers, clamps, hoses and tubes to access the travel motor
- Using a tool and hoist to remove the travel motor, which weighs 120kg
- Cleaning mating surfaces, checking seals and reinstalling components in reverse order
It then details disassembling and assembling the travel motor, including removing the head assembly, brake piston, cylinder assembly parts and seals. Precautions are given to prevent damage and clean/oil parts during reassembly.
The document provides instructions for removing and installing a fuel injection pump on a 320DL excavator with a C6.4 engine. It describes:
1) Removing components like hoses, tubes, brackets and gears to access the fuel injection pump.
2) Using identification marks and tooling to properly align gears during removal and installation.
3) Cleaning components thoroughly before installation to prevent contamination.
4) Installing the fuel injection pump by reversing the removal steps and ensuring proper torque of fasteners.
The document provides instructions for removing and installing various engine components on a Caterpillar 330D2 excavator, including the engine oil pump, water pump, water temperature regulator, and flywheel. The procedures note required tools and safety precautions. Components must be clean and free of damage, with replacement of worn parts. Proper torque values are specified for reinstallation of components.
Caterpillar cat 302.4 d mini hydraulic excavator (prefix ljn) service repair ...fjsjekdmmeme
The document provides instructions for removing and installing various components on a 302.4D Mini Hydraulic Excavator, including the final drive, travel motor, swivel, swing motor, swing drive, ball valve for the adjustable undercarriage, and undercarriage cylinder. The procedures note removing bolts, plugs, and hoses and lifting components out after draining hydraulic oil. Safety precautions are highlighted regarding contained fluids, pressurized cylinders, and spring forces.
Caterpillar cat 301.6 mini hydraulic excavator (prefix my6) service repair ma...fjsjekdmmeme
The document provides instructions for disassembling and assembling a blade cylinder for a 301.6 Mini Hydraulic Excavator. The disassembly procedure involves removing seals and other components from both ends of the cylinder. The assembly procedure describes installing the components in reverse order and applying the appropriate torque to fasteners. Separate sections also describe removing and installing the excavator's blade and bucket.
Caterpillar cat 320 d l excavator (prefix a9f) service repair manual (a9f0000...fikskkdmmd1
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. The removal process involves using specialized tools to compress the valve springs so the valves can be serviced while keeping the piston at top dead center. Installation requires cleaning components, lubricating the valves, and using tools to carefully compress the springs into place. Proper assembly procedure and safety precautions are emphasized to avoid injury from the force of the compressed springs.
Caterpillar cat 320 d excavator (prefix kgf) service repair manual (kgf00001 ...fikskkdmmd1
This document provides instructions for disassembling and assembling the travel motor of a 320D L excavator. The disassembly process includes 27 steps to remove components like the head, fittings, seals, brake piston, plates, and barrel assembly. The assembly section outlines 13 steps including installing seals, keys, cam plate, springs, and piston shoe assemblies back into the barrel assembly and body of the travel motor. Special care must be taken to align parts properly and not allow other components to come apart during the process.
Caterpillar cat 320 track type excavator (prefix 2 dl) service repair manual ...fikskkdmmd1
This document provides instructions for removing and installing valve stem seals on Caterpillar 320, 320L, and 320N track-type excavators. The procedure involves using a seal pick tool to remove the old seals from the valve guides and install new seals. Technicians are instructed to keep all parts clean and coat the new seals with engine oil during installation.
Caterpillar cat 320 s excavator (prefix 3 xk) service repair manual (3xk00822...fikskkdmmd1
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 320 excavator models. The removal procedure involves disconnecting tubes, removing clips and pins connecting the governor. Installation requires applying lubricant to seals, connecting the governor with pins and clips, and reinstalling the fuel injection control linkage using bolts. Tools including special pliers and pins are required. Referenced documents provide additional guidance on inspection and adjustment.
Caterpillar cat 320 n excavator (prefix 4 zj) service repair manual (4zj00460...fikskkdmmd1
1. The document provides instructions for removing and installing final drives on 320-series excavators. It describes disconnecting hydraulic lines, removing mounting bolts, and using hoists to lift heavy components like the final drive, ring gear, and carrier assemblies.
2. Detailed steps are given for disassembling the final drive components, including removing planetary gears, sun gears, and thrust washers. Special tools are required for removing retaining rings. Identification marks should be made on parts for reassembly.
3. Reassembly requires applying threadlock to bolts and anti-seize compound to bearings. Proper shim thickness must be determined to set bearing preload. Duo-Cone seals must be installed
Caterpillar cat 301.8 mini hydraulic excavator (prefix h8 x) service repair m...fjsjekdmmeme
The documents provide instructions for removing and installing various components on a 301.8 Mini Hydraulic Excavator, including the blade, bucket, bucket linkage, and bucket cylinder. The procedures describe disconnecting hoses, removing bolts and pins, lifting components, and installing components in the reverse order of removal. Safety precautions are provided, such as relieving system pressure before disassembling cylinders.
The document provides assembly instructions for installing a swing gear and bearing on an excavator. It lists required tools and parts. The procedure involves cleaning the swing gear and bearing, applying lubricant and sealant, lifting it into position using links, and securing it with bolts torqued to specification. Inner and outer dust seals are installed in seal grooves before completing reassembly of the undercarriage frame.
Caterpillar cat 311 b track type excavator (prefix 2ls) service repair manual...fjskefkemms
This document provides instructions for servicing components of a 311B excavator engine, including:
1) Instructions for assembling the rocker shaft, including the components and installation steps.
2) Instructions for installing the rocker shaft and pushrods, including torque specifications.
3) Instructions for removing the cylinder head, including removal steps and safety notices.
Caterpillar cat 303.5 c cr mini hydraulic excavator (prefix dmy) service repa...fjsjekdmmeme
The document provides instructions for disassembling and inspecting various engine components of a 303.5C Mini Hydraulic Excavator, including the timing gear, camshaft, oil pan, piston, connecting rod, crankshaft, and cylinder block. It lists the components in their order of disassembly and provides illustrations showing how to remove each part. Specifications for measuring component wear limits are also provided to determine if parts need replacing. Safety notes are included throughout to warn of potential dangers during disassembly.
Caterpillar cat c2.2 industrial engine (prefix g7 m) service repair manual (g...ifkkdmdmdm
The document provides instructions for removing and installing the crankshaft pulley and front seal on an industrial engine. It describes removing the pulley by drilling holes in the seal, inserting a puller tool, and removing the woodruff key from the crankshaft. For installation, it instructs to clean components, insert the key, lubricate parts, and tighten the pulley nut to the specified torque. It also describes removing the front housing by removing mounting nuts and identifying locating features.
Caterpillar cat 311 c excavator (prefix cke) service repair manual (cke00001 ...fjskefkemms
This service repair manual provides instructions for removing and installing inlet and exhaust valve seals on models 311C and 311C U excavators. The procedures describe using a seal pick tool to remove old seals from valve guides and installing new seals. Safety notices are included to keep parts clean and contain fluids.
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 320 excavator models. It describes the required tools and gives a step-by-step process including removing clips and pins, sliding tubes, and removing/installing parts like the governor, linkage, and seals using special tools. References are provided for more information on governors and linkage inspection procedures.
Caterpillar cat 320 d l excavator (prefix kzf) service repair manual (kzf0000...fkjsekksmem
The document provides instructions for disassembling and assembling a final drive for excavator models 320D and 320D L. It describes 33 steps to disassemble the final drive components including removing bolts, shafts, gears, seals, and bearings. It then describes 32 steps for reassembling the final drive, applying sealant and lubricant, and installing components in reverse order using pressing and lifting tools. Precision is required to determine shim thickness for proper bearing preload.
Caterpillar cat m316 d wheeled excavator (prefix w6a) service repair manual (...fujsjefjwerkskemm
This document provides instructions for removing and installing an idler gear on a Caterpillar C6.6 engine. It describes the required tools and steps to:
1) Lock the camshaft and crankshaft in position, remove bolts, and remove the standard or heavy-duty idler gear.
2) Clean and inspect the idler gear components, install the idler gear while aligning timing marks, install bolts, and check end play and backlash.
3) Ensure the number one piston is at top dead center before installing the idler gear in the correct position and alignment.
Caterpillar cat 304.5 e mini hydraulic excavator (prefix fxt) service repair ...fjskekfseik
The document provides instructions for removing and installing piston and connecting rod assemblies in an engine. Key steps include:
1. Removing the cylinder head and oil pan before removing the piston and connecting rod.
2. Pushing the connecting rod and piston out of the cylinder block after removing the connecting rod cap and bearings.
3. Reversing the removal procedures to install the piston and connecting rod assemblies, ensuring correct orientation and applying lubricant to moving parts.
Caterpillar cat 305 cr mini hydraulic excavator (prefix dsa) service repair m...fjskekfseik
The document provides instructions for removing and disassembling the travel motor from a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing the track and final drive sprocket. Disassembly involves marking parts, draining oil, removing plates, barrels and pistons. Multiple gears, shafts, seals and other internal components are then dismantled from the travel motor housing.
Caterpillar cat 16 h na motor grader (prefix 6zj) service repair manual (6zj0...fjskefkemms
This document provides instructions for removing and installing various engine components on a 16H NA Motor Grader with a 3406C engine, including:
1. Timing gears and plate removal and installation.
2. Camshaft removal and installation.
3. Camshaft bearing removal and installation.
4. Connecting rod bearing removal and installation.
5. Crankshaft main bearing removal and installation.
The instructions describe the individual steps for removing and installing each component, including the use of any necessary tools. Safety notices and additional notes are also provided throughout.
Caterpillar cat 330 track type excavator (prefix 6 wj) service repair manual ...fjskefkemms
This document provides instructions for removing and installing travel motors on 330 and 330L excavator models. It describes:
- Releasing hydraulic pressure before removing components
- Removing covers, clamps, hoses and tubes to access the travel motor
- Using a tool and hoist to remove the travel motor, which weighs 120kg
- Cleaning mating surfaces, checking seals and reinstalling components in reverse order
It then details disassembling and assembling the travel motor, including removing the head assembly, brake piston, cylinder assembly parts and seals. Precautions are given to prevent damage and clean/oil parts during reassembly.
The document provides instructions for removing and installing a fuel injection pump on a 320DL excavator with a C6.4 engine. It describes:
1) Removing components like hoses, tubes, brackets and gears to access the fuel injection pump.
2) Using identification marks and tooling to properly align gears during removal and installation.
3) Cleaning components thoroughly before installation to prevent contamination.
4) Installing the fuel injection pump by reversing the removal steps and ensuring proper torque of fasteners.
The document provides instructions for removing and installing various engine components on a Caterpillar 330D2 excavator, including the engine oil pump, water pump, water temperature regulator, and flywheel. The procedures note required tools and safety precautions. Components must be clean and free of damage, with replacement of worn parts. Proper torque values are specified for reinstallation of components.
Caterpillar cat 302.4 d mini hydraulic excavator (prefix ljn) service repair ...fjsjekdmmeme
The document provides instructions for removing and installing various components on a 302.4D Mini Hydraulic Excavator, including the final drive, travel motor, swivel, swing motor, swing drive, ball valve for the adjustable undercarriage, and undercarriage cylinder. The procedures note removing bolts, plugs, and hoses and lifting components out after draining hydraulic oil. Safety precautions are highlighted regarding contained fluids, pressurized cylinders, and spring forces.
Caterpillar cat 301.6 mini hydraulic excavator (prefix my6) service repair ma...fjsjekdmmeme
The document provides instructions for disassembling and assembling a blade cylinder for a 301.6 Mini Hydraulic Excavator. The disassembly procedure involves removing seals and other components from both ends of the cylinder. The assembly procedure describes installing the components in reverse order and applying the appropriate torque to fasteners. Separate sections also describe removing and installing the excavator's blade and bucket.
Caterpillar cat 320 d l excavator (prefix a9f) service repair manual (a9f0000...fikskkdmmd1
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. The removal process involves using specialized tools to compress the valve springs so the valves can be serviced while keeping the piston at top dead center. Installation requires cleaning components, lubricating the valves, and using tools to carefully compress the springs into place. Proper assembly procedure and safety precautions are emphasized to avoid injury from the force of the compressed springs.
Caterpillar cat 320 d excavator (prefix kgf) service repair manual (kgf00001 ...fikskkdmmd1
This document provides instructions for disassembling and assembling the travel motor of a 320D L excavator. The disassembly process includes 27 steps to remove components like the head, fittings, seals, brake piston, plates, and barrel assembly. The assembly section outlines 13 steps including installing seals, keys, cam plate, springs, and piston shoe assemblies back into the barrel assembly and body of the travel motor. Special care must be taken to align parts properly and not allow other components to come apart during the process.
Caterpillar cat 320 track type excavator (prefix 2 dl) service repair manual ...fikskkdmmd1
This document provides instructions for removing and installing valve stem seals on Caterpillar 320, 320L, and 320N track-type excavators. The procedure involves using a seal pick tool to remove the old seals from the valve guides and install new seals. Technicians are instructed to keep all parts clean and coat the new seals with engine oil during installation.
Caterpillar cat 320 s excavator (prefix 3 xk) service repair manual (3xk00822...fikskkdmmd1
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 320 excavator models. The removal procedure involves disconnecting tubes, removing clips and pins connecting the governor. Installation requires applying lubricant to seals, connecting the governor with pins and clips, and reinstalling the fuel injection control linkage using bolts. Tools including special pliers and pins are required. Referenced documents provide additional guidance on inspection and adjustment.
Caterpillar cat 320 n excavator (prefix 4 zj) service repair manual (4zj00460...fikskkdmmd1
1. The document provides instructions for removing and installing final drives on 320-series excavators. It describes disconnecting hydraulic lines, removing mounting bolts, and using hoists to lift heavy components like the final drive, ring gear, and carrier assemblies.
2. Detailed steps are given for disassembling the final drive components, including removing planetary gears, sun gears, and thrust washers. Special tools are required for removing retaining rings. Identification marks should be made on parts for reassembly.
3. Reassembly requires applying threadlock to bolts and anti-seize compound to bearings. Proper shim thickness must be determined to set bearing preload. Duo-Cone seals must be installed
Caterpillar cat 320 n excavator (prefix 3 xk) service repair manual (3xk00822...fikskkdmmd1
This document provides instructions for removing and installing a fuel injection control linkage on Caterpillar 320 excavator models. The removal procedure involves taking out the rocker shaft and pushrods, then removing clips and a clevis pin to detach the governor from the linkage. Installation requires reattaching these components using special tools, adjusting brackets, and compressing injector springs during assembly. References are provided for additional maintenance information.
Caterpillar cat 320 l excavator (prefix 4 zj) service repair manual (4zj00460...fikskkdmmd1
This document provides instructions for removing and installing final drives on 320-series excavators. It outlines the steps to release hydraulic pressure, remove the final drive housing, and disassemble/reassemble the internal components. The process involves removing 20 bolts, hydraulic lines, and using lifting tools to maneuver heavy internal parts like carriers, gears, and housings weighing up to 82 kg. Proper cleaning, lubrication, and torque specifications are noted to ensure correct reassembly.
Caterpillar cat 320 l excavator (prefix 3 xk) service repair manual (3xk00822...fikskkdmmd1
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 320 excavator models. It describes the required tools and gives a step-by-step process including removing clips and pins, sliding tubes, and removing/installing parts like the governor, linkage, and seals using special tools. References are provided for more information on governors and linkage inspection procedures.
The document provides instructions for disassembling and assembling the travel motor of a 320 GC excavator. It lists the required tools and parts. The disassembly process involves removing plugs and seals from the motor housing. Springs must be released carefully due to risk of injury. The brake piston is then unseated using air pressure before internal components of the motor can be accessed and replaced. The assembly procedure reverses the disassembly steps.
This service repair manual provides instructions for installing a flywheel and crankshaft rear seal on a Caterpillar C4.4 engine. It outlines the required tools and steps to remove and install the flywheel housing. The procedures include inspecting parts for leaks, aligning seals and gaskets, and torquing bolts to the specified values.
This document provides instructions for removing and installing final drives on 320-series excavators. It outlines the steps to release hydraulic pressure, remove the final drive housing, and disassemble/reassemble the internal components. The process involves removing 20 bolts, hydraulic lines, and using lifting tools to maneuver heavy internal parts like carriers, gears, and housings weighing up to 82 kg. Proper cleaning, lubrication, and torque specifications are noted to ensure correct reassembly.
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 320 excavator models. It describes the required tools and gives a step-by-step process including removing clips and pins, sliding tubes, and removing/installing parts like the governor, linkage, and seals using special tools. References are provided for more information on governors and linkage inspection procedures.
Caterpillar cat 305 e2cr mini hydraulic excavator (prefix pyr) service repair...fikskkdmmd1
The document provides instructions for servicing various components of a Caterpillar 305E2 CR mini hydraulic excavator engine. It describes procedures for removing and installing components like the idler gear, front housing, valve mechanism cover, rocker shaft and push rods. The steps include using proper tooling, alignment marks, torque specifications and cleaning/lubricating parts.
Caterpillar cat 305 e2 cr mini hydraulic excavator (prefix djx) service repai...fikskkdmmd1
This document provides instructions for removing and installing various engine components on a 305E2 CR Mini Hydraulic Excavator including:
- Crankshaft rear seal
- Flywheel housing
- Crankshaft pulley
- Crankshaft front seal
- Idler gear
The procedures include illustrations and describe using various tools to disassemble, clean, inspect, and reinstall each component according to the specified instructions and torque specifications.
Caterpillar cat 305 e2 cr mini hydraulic excavator (prefix df5) service repai...fikskkdmmd1
The document provides instructions for removing and installing various components of a 305E2 CR Mini Hydraulic Excavator engine, including the fuel injection lines, exhaust gas recirculation cooler, fuel injection pump, electronic unit injector, and turbocharger. Safety precautions are outlined that must be followed when working on fuel system and high temperature components.
Caterpillar cat 305 e2 cr mini hydraulic excavator (prefix bz5) service repai...fikskkdmmd1
This document provides instructions for removing and installing various components of a 305E2 CR Mini Hydraulic Excavator engine, including:
- Removing the fuel manifold by removing bolts and lines, taking care not to damage sensors.
- Removing fuel injection lines by disconnecting hoses and tubes after capping lines to prevent contamination.
- Removing the exhaust gas recirculation cooler by draining coolant and removing hoses and mounting brackets.
- Removing the fuel injection pump by disconnecting lines and hoses and removing nuts and bolts.
- Removing electronic unit injectors by disconnecting hoses after taking safety precautions for the high pressure fuel system.
Caterpillar cat 305 cr mini hydraulic excavator (prefix dsa) service repair m...fikskkdmmd1
The document provides instructions for removing and disassembling the travel motor from a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing the track and final drive sprocket. Disassembly involves removing plates, barrels, pistons, springs, gears and other components using various tools. Detailed steps and illustrations are provided to label parts and ensure correct reassembly.
Caterpillar cat 305 cr mini hydraulic excavator (prefix dgt) service repair m...fikskkdmmd1
The document provides instructions for removing the swivel on a 305CR Mini Hydraulic Excavator. The steps include:
1. Releasing hydraulic system pressure and removing the cab.
2. Disconnecting and plugging multiple hose assemblies connected to the swivel.
3. Removing bolts and a plate from the bottom of the carbody.
Caterpillar cat 305 c cr mini hydraulic excavator (prefix hwj) service repair...fikskkdmmd1
The document provides instructions for disassembling and inspecting various engine components of a 305C CR Mini Hydraulic Excavator, including the timing gear, camshaft, oil pan, piston, connecting rod, crankshaft, and cylinder block. It lists the components in their disassembly sequence and provides illustrations and instructions for removing each part. Tolerances and limits are provided for measuring various components like gear backlash, end play, and clearance.
Caterpillar cat 305.5 e2cr mini hydraulic excavator (prefix shw) service repa...fikskkdmmd1
The document provides instructions for removing and installing various engine components on a Caterpillar 305.5E2CR mini hydraulic excavator powered by a C2.4 engine. The components include the idler gear, front housing, valve mechanism cover, rocker shaft and push rods, and disassembling the rocker shaft. The procedures note required tools, removal steps, installation steps including torque specifications and lubrication points.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D L EXCAVATOR DHK
Configuration: 320D & 320D L Excavators DHK00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
320D Excavator Machine Systems
Media Number -RENR8614-14 Publication Date -01/05/2013 Date Updated -19/07/2017
i07316669
Boom Cylinder - Remove and Install
SMCS - 5456-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 4C-9485 Pin Driver Cap 1
Cylinders equipped with lock valves can remain pressurized for very
long periods of time, even with the hoses removed.
Failure to relieve pressure before removing a lock valve or
disassembling a cylinder can result in personal injury or death.
Ensure all pressure is relieved before removing a lock valve or
disassembling a cylinder.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/12(W)
w
2020/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
1. Fully extend the bucket cylinder. Fully extend the stick cylinder. Lower the boom until the
stick assembly is in contact with the ground.
2. Release the pressure in the hydraulic system. Refer to Disassembly and Assembly, "Hydraulic
System Pressure - Release".
Illustration 1 g01217839
Illustration 2 g01217840
3. Loosen nut (1). Turn bolt (2) counterclockwise to release the pressure in the cylinder.
2/12(W)
w
2020/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. Illustration 3 g01217850
4. Remove bolts (3).
Illustration 4 g01217906
5. Remove clamps (4).
Illustration 5 g01217908
6. Remove bolts (6) and support assemblies (5).
3/12(W)
w
2020/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Illustration 6 g01217912
7. Remove bolts (7) and reposition tube assembly (8) out of the way.
Illustration 7 g01217915
8. Remove bolts (9) and reposition valve assembly (10) out of the way.
Illustration 8 g01217921
9. Attach a suitable lifting device to boom cylinder (11). The weight of boom cylinder (11) is
approximately 287 kg (632 lb).
4/12(W)
w
2020/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Illustration 9 g01217928
10. Remove bolts (12) and plate (13). Remove spacer (14) (not shown).
Illustration 10 g01218003
Illustration 11 g01218010
11. Attach Tooling (A) to pin (15). Use a suitable driver to reposition pin (15). Remove shim (16).
5/12(W)
w
2020/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Illustration 12 g01218011
12. Lower boom cylinder (11) onto suitable cribbing and attach a suitable lifting device to boom
cylinder (11), as shown. The weight of boom cylinder (11) is approximately 287 kg (632 lb).
Illustration 13 g01218013
13. Remove bolt (18). Remove pin assembly (19) and shims (17). Remove boom cylinder (11).
Disassembly and Assembly Information
Table 2
Required Tools
Tool Part Number Part Description Qty
B 127-4904 Hydraulic Cylinder Repair Stand Gp 1
C 7M-7456 Bearing Mount Compound 1
D 1P-0808 Multipurpose Grease 1
E 195-4609 Seal Pick 1
F 3S-6224 Electric Hydraulic Pump Gp 1
6V-3175 Double Acting Cylinder 1
9S-5564 Pin Puller Sleeve As 1
6/12(W)
w
2020/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. 9U-6832 Nut 1
4C-9634 Puller Stud 1
9U-5338 Bearing Puller Adapter 1
G
3S-6224 Electric Hydraulic Pump Gp 1
6V-3175 Double Acting Cylinder 1
9S-5564 Pin Puller Sleeve As 1
9U-6832 Nut 1
4C-9634 Puller Stud 1
9U-5339 Bearing Puller Adapter 1
Cylinders equipped with lock valves can remain pressurized for very
long periods of time, even with the hoses removed.
Failure to relieve pressure before removing a lock valve or
disassembling a cylinder can result in personal injury or death.
Ensure all pressure is relieved before removing a lock valve or
disassembling a cylinder.
Illustration 14 g01218033
Note: Tooling (F) is used for the removal and installation of bearing (8). Tooling (G) is used for the
removal and installation of bearing (2).
Refer to Table 3 for the correct torque specification for piston (3).
Refer to Table 3 for the correct torque specification for bolts (1).
Table 3
Torque Table
7/12(W)
w
2020/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Piston or
Lock Nut
Piston / Lock Nut
Thread Size
Piston / Lock Nut (3) Torque
Specification
Head Bolts (1) Torque
Specification
Lock Nut M64
5900 ± 300 N·m
(4352 ± 221 lb ft)
460 ± 60 N·m
(339 ± 44 lb ft)
Piston M65
5460 ± 260 N·m
(4027 ± 192 lb ft)
267 ± 40 N·m
(197 2 ± 30 lb ft)
Lock Nut M72
7400 ± 370 N·m
(5458 ± 273 lb ft)
460 ± 60 N·m
(339 ± 44 lb ft)
Piston M75
7890 ± 395 N·m
(5819 ± 291 lb ft)
367 ± 55 N·m
(270 ± 40 lb ft)
Piston M80
8900 ± 445 N·m
(6564 ± 328 lb ft)
367 ± 55 N·m
(270 ± 40 lb ft)
Lock Nut M80
7900 ± 400 N·m
(5827 ± 295 lb ft)
800 ± 100 N·m
(590 ± 74 lb ft)
Piston M85
10000 ± 500 N·m
(7376 ± 368 lb ft)
520 ± 78 N·m
(384 ± 58 lb ft)
Piston and
Lock Nut
Piston is M75
980 to 1176 N·m
(722 to 867 lb ft) 333 to 352 N·m
(245 to 260 lb ft)
Lock Nut is M62
1862 to 1960 N·m
(1373 to 1446 lb ft)
Tighten the setscrew that retains nut (3) to a torque of 57 ± 11 N·m (42 ± 8 lb ft).
The slit of ring (5) must be in the direction of the piston.
Apply Tooling (D) to seals (4) prior to assembly.
Lubricate seals (6) with the lubricant that is being sealed.
Apply Tooling (C) to the wiper seal (7) prior to assembly.
Installation Procedure
Table 4
Required Tools
Tool Part Number Part Description Qty
A 4C-9485 Pin Driver Cap 1
8/12(W)
w
2020/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Illustration 15 g01218011
1. Attach a suitable lifting device to boom cylinder (11), as shown. The weight of boom cylinder
(11) is approximately 287 kg (632 lb). Position boom cylinder (11) onto the machine.
Illustration 16 g01218013
2. Install shims (17) and pin assembly (19) on the head end of boom cylinder (11). Install bolt
(18).
Illustration 17 g01217921
3. Use the suitable lifting device to position boom cylinder (11) onto suitable cribbing. Reposition
the suitable lifting device near the rod end of boom cylinder (11). The weight of boom cylinder
(11) is approximately 287 kg (632 lb). Use the suitable lifting device to raise the rod end of
boom cylinder (11) into position.
9/12(W)
w
2020/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Illustration 18 g01218505
Illustration 19 g01217928
4. Install shim (16). Position pin (15) through the rod end of the boom cylinder.
5. Install spacer (14) (not shown). Install plate (13) and bolts (12).
Illustration 20 g01217915
6. Position valve assembly (10) and install bolts (9).
10/12(W)
w
2020/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Illustration 21 g01217912
7. Position tube assembly (8) and install bolts (7).
Illustration 22 g01217908
8. Install support assemblies (5) and bolts (6).
Illustration 23 g01217906
9. Install clamps (4).
11/12(W)
w
2020/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Illustration 24 g01217850
10. Install bolts (3).
Illustration 25 g01217839
Illustration 26 g01217840
11. Turn bolt (2) clockwise into the original position. Tighten nut (1).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jan 25 17:19:09 UTC+0800 2020
12/12(W)
w
2020/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D L EXCAVATOR DHK
Configuration: 320D & 320D L Excavators DHK00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
320D Excavator Machine Systems
Media Number -RENR8614-14 Publication Date -01/05/2013 Date Updated -19/07/2017
i02462986
Boom - Remove
SMCS - 6501-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 4C-9485 Pin Driver Cap 1
B 1U-9202 Lever Puller Hoist 1
C
3S-6224 Electric Hydraulic Pump Gp 1
141-1785 Receiving Sleeve 1
9U-6811 Puller Stud 1
9U-6809 Nut 1
6V-0113 Double Acting Cylinder 1
Start By:
A. Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic
System Pressure - Release".
B. Remove the stick. Refer to Disassembly and Assembly, "Stick - Remove".
1/7(W)
w
2020/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Illustration 1 g01212856
1. Disconnect grease hose assembly (1) from boom cylinder (3). Remove bolts (2). Remove
the retainer plate and spacer (4).
Illustration 2 g01212871
Illustration 3 g01212838
2/7(W)
w
2020/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. 2. Attach a suitable lifting device to boom cylinder (3). The weight of boom cylinder (3) is
approximately 287 kg (633 lb). Install Tooling (A) into pin (5). Use a hammer to drive pin
(5) out of boom cylinder (3). Lower boom cylinder (3) .
Note: Remove any shims that may be present. Mark the shims for installation purposes.
3. Repeat Steps 1 through 2 for the other boom cylinder.
Illustration 4 g01212891
4. Remove bolts (6). Remove cover (7) .
Illustration 5 g01212899
5. Remove three bolts (8). Remove step (9) .
3/7(W)
w
2020/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Illustration 6 g01212931
Illustration 7 g01212925
6. Open cover (10) of the storage box. Remove bolts (13). Remove bolts (12) and remove
handhold (11) .
4/7(W)
w
2020/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
19. Illustration 8 g01228933
7. Position retainer plate (4) and bolts (2) onto each side of pin (5). Attach a suitable lifting
device to each side of pin (5) .
Illustration 9 g01217554
Illustration 10 g01212951
8. Attach a suitable lifting device to pin assembly (15). The weight of pin assembly (15) is
approximately 48 kg (105 lb). Install pin assembly (15) and install bolt (16) .
9. Attach Tooling (B) and a suitable lifting device to boom (14) and pin assembly (15). The
combined weight of boom (14) and the stick cylinder is between 1500 kg (3300 lb) and
3016 kg (6650 lb). Apply slight lifting tension to boom (14) .
5/7(W)
w
2020/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Illustration 14 g01212983
12. Remove bolt (24). Attach a suitable lifting device to Tooling (C). The weight of Tooling (C)
is approximately 136 kg (300 lb). Attach Tooling (C) to pin assembly (23). Use Tooling (C)
in order to remove pin assembly (23). The combined weight of Tooling (C) and pin
assembly (23) is approximately 215 kg (475 lb).
13. Remove the boom. Remove any shims that may be present.
Note: Note the locations of any shims for assembly purposes.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jan 25 17:20:04 UTC+0800 2020
7/7(W)
w
2020/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D L EXCAVATOR DHK
Configuration: 320D & 320D L Excavators DHK00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
320D Excavator Machine Systems
Media Number -RENR8614-14 Publication Date -01/05/2013 Date Updated -19/07/2017
i07137701
Boom Bearings and Seals - Remove and Install
SMCS - 6501-010-SA; 6501-010-BD
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
350-7768 Electric Hydraulic Pump Gp (115V) -1
350-7769 Electric Hydraulic Pump Gp(230V) -
4C-9634 Puller Stud 1
9U-6832 Nut 1
5P-8712 Bushing 1
316-1489 Double Acting Cylinder 1
134-8469 Spacer 1
9U-5338 Bearing Puller Adapter 1
Start By:
a. Remove the boom. Refer to Disassembly and Assembly, "Boom - Remove".
1/4(W)
w
2020/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...