This document provides instructions for removing and installing a fuel injection control linkage on Caterpillar 320 excavator models. The removal procedure involves taking out the rocker shaft and pushrods, then removing clips and a clevis pin to detach the governor from the linkage. Installation requires reattaching these components using special tools, adjusting brackets, and compressing injector springs during assembly. References are provided for additional maintenance information.
Caterpillar cat 320 d l excavator (prefix a9f) service repair manual (a9f0000...fjskekfseik
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. The removal process involves using specialized tools to compress the valve springs so the valves can be serviced while keeping the piston at top dead center. Installation requires cleaning components, lubricating the valves, and using tools to carefully compress the springs into place. Proper assembly procedure and safety precautions are emphasized to avoid injury from released spring forces.
Caterpillar cat 301.6 mini hydraulic excavator (prefix my6) service repair ma...fjsjekdmmeme
The document provides instructions for disassembling and assembling a blade cylinder for a 301.6 Mini Hydraulic Excavator. The disassembly procedure involves removing seals and other components from both ends of the cylinder. The assembly procedure describes installing the components in reverse order and applying the appropriate torque to fasteners. Separate sections also describe removing and installing the excavator's blade and bucket.
Caterpillar cat 303.5 c cr mini hydraulic excavator (prefix dmy) service repa...fjsjekdmmeme
The document provides instructions for disassembling and inspecting various engine components of a 303.5C Mini Hydraulic Excavator, including the timing gear, camshaft, oil pan, piston, connecting rod, crankshaft, and cylinder block. It lists the components in their order of disassembly and provides illustrations showing how to remove each part. Specifications for measuring component wear limits are also provided to determine if parts need replacing. Safety notes are included throughout to warn of potential dangers during disassembly.
Caterpillar cat 304 c cr mini hydraulic excavator (prefix fpk) service repair...fjskekfseik
The document provides instructions for disassembling and inspecting various components of a 304C CR Mini Hydraulic Excavator, including the cylinder head, valve mechanism, flywheel, timing gears, camshaft, and oil pan. The steps include removing fasteners and assemblies, inspecting parts for wear or damage, and measuring components to check if they are within standard limits. Clearances and end plays are checked using feeler gauges or dial indicators to determine if replacement is needed.
Caterpillar cat 330 track type excavator (prefix 6 wj) service repair manual ...fjskefkemms
This document provides instructions for removing and installing travel motors on 330 and 330L excavator models. It describes:
- Releasing hydraulic pressure before removing components
- Removing covers, clamps, hoses and tubes to access the travel motor
- Using a tool and hoist to remove the travel motor, which weighs 120kg
- Cleaning mating surfaces, checking seals and reinstalling components in reverse order
It then details disassembling and assembling the travel motor, including removing the head assembly, brake piston, cylinder assembly parts and seals. Precautions are given to prevent damage and clean/oil parts during reassembly.
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 320 excavator models. It describes the required tools and gives a step-by-step process including removing clips and pins, sliding tubes, and removing/installing parts like the governor, linkage, and seals using special tools. References are provided for more information on governors and linkage inspection procedures.
Caterpillar cat 303 c cr mini hydraulic excavator (prefix bxt) service repair...fjsjekdmmeme
This document provides instructions for disassembling and inspecting various engine components of a 303C CR Mini Hydraulic Excavator, including the timing gear, camshaft, oil pan, piston, connecting rod, crankshaft, and cylinder block. It outlines the disassembly sequence and steps to remove each part, and provides illustrations. Tolerances and limits are provided for inspecting components like gears, bearings, and shaft ends to determine if replacement is needed.
This document provides instructions for installing a flywheel and removing and installing a wet back end flywheel housing on a Caterpillar 320 GC excavator. It describes using guide studs and lifting devices to position the heavy flywheel and housing. Torque specifications and tightening sequences are given for installing mounting bolts. Replacing seals, gaskets and dowels is also covered.
Caterpillar cat 320 d l excavator (prefix a9f) service repair manual (a9f0000...fjskekfseik
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. The removal process involves using specialized tools to compress the valve springs so the valves can be serviced while keeping the piston at top dead center. Installation requires cleaning components, lubricating the valves, and using tools to carefully compress the springs into place. Proper assembly procedure and safety precautions are emphasized to avoid injury from released spring forces.
Caterpillar cat 301.6 mini hydraulic excavator (prefix my6) service repair ma...fjsjekdmmeme
The document provides instructions for disassembling and assembling a blade cylinder for a 301.6 Mini Hydraulic Excavator. The disassembly procedure involves removing seals and other components from both ends of the cylinder. The assembly procedure describes installing the components in reverse order and applying the appropriate torque to fasteners. Separate sections also describe removing and installing the excavator's blade and bucket.
Caterpillar cat 303.5 c cr mini hydraulic excavator (prefix dmy) service repa...fjsjekdmmeme
The document provides instructions for disassembling and inspecting various engine components of a 303.5C Mini Hydraulic Excavator, including the timing gear, camshaft, oil pan, piston, connecting rod, crankshaft, and cylinder block. It lists the components in their order of disassembly and provides illustrations showing how to remove each part. Specifications for measuring component wear limits are also provided to determine if parts need replacing. Safety notes are included throughout to warn of potential dangers during disassembly.
Caterpillar cat 304 c cr mini hydraulic excavator (prefix fpk) service repair...fjskekfseik
The document provides instructions for disassembling and inspecting various components of a 304C CR Mini Hydraulic Excavator, including the cylinder head, valve mechanism, flywheel, timing gears, camshaft, and oil pan. The steps include removing fasteners and assemblies, inspecting parts for wear or damage, and measuring components to check if they are within standard limits. Clearances and end plays are checked using feeler gauges or dial indicators to determine if replacement is needed.
Caterpillar cat 330 track type excavator (prefix 6 wj) service repair manual ...fjskefkemms
This document provides instructions for removing and installing travel motors on 330 and 330L excavator models. It describes:
- Releasing hydraulic pressure before removing components
- Removing covers, clamps, hoses and tubes to access the travel motor
- Using a tool and hoist to remove the travel motor, which weighs 120kg
- Cleaning mating surfaces, checking seals and reinstalling components in reverse order
It then details disassembling and assembling the travel motor, including removing the head assembly, brake piston, cylinder assembly parts and seals. Precautions are given to prevent damage and clean/oil parts during reassembly.
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 320 excavator models. It describes the required tools and gives a step-by-step process including removing clips and pins, sliding tubes, and removing/installing parts like the governor, linkage, and seals using special tools. References are provided for more information on governors and linkage inspection procedures.
Caterpillar cat 303 c cr mini hydraulic excavator (prefix bxt) service repair...fjsjekdmmeme
This document provides instructions for disassembling and inspecting various engine components of a 303C CR Mini Hydraulic Excavator, including the timing gear, camshaft, oil pan, piston, connecting rod, crankshaft, and cylinder block. It outlines the disassembly sequence and steps to remove each part, and provides illustrations. Tolerances and limits are provided for inspecting components like gears, bearings, and shaft ends to determine if replacement is needed.
This document provides instructions for installing a flywheel and removing and installing a wet back end flywheel housing on a Caterpillar 320 GC excavator. It describes using guide studs and lifting devices to position the heavy flywheel and housing. Torque specifications and tightening sequences are given for installing mounting bolts. Replacing seals, gaskets and dowels is also covered.
Caterpillar cat 304.5 mini hydraulic excavator (prefix anr) service repair ma...fjsjekdmmeme
The document provides instructions for disassembling and assembling a piston pump. It lists 34 steps for disassembling the pump, removing components like the piston, valve, plates, seals and bearings. It then lists 32 steps for assembling the pump, installing the components in reverse order and ensuring new seals and O-rings are used. Cleanliness is emphasized throughout to prevent contaminants from entering the system. Tools including snap ring pliers are required.
Caterpillar cat 303.5 e2 mini hydraulic excavator (prefix jwy) service repair...fjsjekdmmeme
The document provides instructions for removing and installing inlet and exhaust valves, valve springs, valve guides, and valve seat inserts on a Caterpillar 303.5E2 Mini Hydraulic Excavator engine. The procedures describe using various tools to compress valve springs, remove components in the proper sequence while keeping them clean, and reinstalling components in the reverse order of removal. Special tools and trained personnel are required for some tasks like removing valve guides and seats.
Caterpillar cat 303 cr mini hydraulic excavator (prefix dma) service repair m...fjsjekdmmeme
This document provides assembly instructions for the main control valve of a 303 CR Mini Hydraulic Excavator. It describes assembling 8 different block assemblies (L through H) that make up the main control valve. The instructions note that cleanliness is important, valves must be assembled in the same configuration, and components must be returned to their original valves. Personal injury warnings are also provided regarding spring forces.
Caterpillar cat 320 l track type excavator (prefix 2dl) service repair manual...fkjsekksmem
This document provides instructions for servicing components of Caterpillar excavator models 320, 320L, and 320N, including:
- Removing and installing inlet and exhaust valve seals
- Removing the engine oil filter base
- Installing the engine oil filter base
- Removing the engine oil cooler
- Disassembling the engine oil cooler
- Reassembling the engine oil cooler
- Installing the engine oil cooler
The document includes diagrams and step-by-step instructions for maintenance procedures. Technicians are advised to keep components clean and contain fluids properly during repair.
Caterpillar cat 329 e excavator (prefix pty) service repair manual (pty00001 ...fkjsekksmem
The document provides instructions for removing and installing components related to the crankshaft on a Caterpillar 329E excavator engine, including:
- Removing and installing the vibration damper and pulley, which involves removing screws and installing guide studs.
- Removing and installing the crankshaft front seal using a removal/installation tool.
- Removing and installing the front cover, which requires identifying bolt positions, cleaning surfaces, and installing a new gasket.
Caterpillar cat 311 c excavator (prefix cke) service repair manual (cke00001 ...fjskefkemms
This service repair manual provides instructions for removing and installing inlet and exhaust valve seals on models 311C and 311C U excavators. The procedures describe using a seal pick tool to remove old seals from valve guides and installing new seals. Safety notices are included to keep parts clean and contain fluids.
Caterpillar cat 305 cr mini hydraulic excavator (prefix dgt) service repair m...fjskekfseik
The document provides instructions for removing the swivel on a 305CR Mini Hydraulic Excavator. It lists the required tools and notes to release hydraulic pressure and remove the cab first. The procedure involves using plugs and caps to seal ports while removing 4 bolts to detach the swivel assembly.
Caterpillar cat m316 d wheeled excavator (prefix w6a) service repair manual (...fujsjefjwerkskemm
This document provides instructions for removing and installing an idler gear on a Caterpillar C6.6 engine. It describes the required tools and steps to:
1) Lock the camshaft and crankshaft in position, remove bolts, and remove the standard or heavy-duty idler gear.
2) Clean and inspect the idler gear components, install the idler gear while aligning timing marks, install bolts, and check end play and backlash.
3) Ensure the number one piston is at top dead center before installing the idler gear in the correct position and alignment.
Caterpillar cat 320 d l excavator (prefix kgf) service repair manual (kgf0000...fkjsekksmem
This document provides instructions for disassembling and assembling the travel motor of a 320D L excavator. The disassembly process includes 27 steps to remove components like the head, fittings, seals, brake piston, plates, and barrel assembly. The assembly section outlines 13 steps including installing seals, keys, cam plate, springs, and piston shoe assemblies back into the barrel assembly and body of the travel motor. Special care must be taken to align parts properly and not allow components to separate during disassembly and assembly.
Caterpillar cat 302.5 mini hydraulic excavator (prefix 4 az) service repair m...fjsjekdmmeme
1) The document provides instructions for removing and installing the fuel injection pump, exhaust manifold, and inlet manifold on a 302.5 Mini Hydraulic Excavator powered by a 3013 engine.
2) To remove the fuel injection pump, disconnect lines and solenoids, remove mounting bolts and nuts, and record shim thickness. To install, position shims and pump, reconnect links, and tighten bolts.
3) Exhaust manifold removal involves removing nuts, bolts and gasket. Installation requires cleaning surfaces, installing new gasket, and tightening bolts.
4) Inlet manifold removal requires removing bolts, gaskets and spacer plate. Installation involves cleaning
Caterpillar cat 304.5 mini hydraulic excavator (prefix wak) service repair ma...fjskekfseik
This document provides instructions for removing the swing motor from a 304.5 Mini Hydraulic Excavator. The instructions include releasing hydraulic system pressure, removing the cab and seat, disconnecting linkages from the left console, and removing bolts to separate the right console to access the swing motor for removal. Proper containment of fluids and marking of disconnected lines and fittings is emphasized.
Caterpillar cat 330 f excavator (prefix lbn) service repair manual (lbn00001 ...fjskekdmjekm
The document provides instructions for disassembling a 330F LN excavator travel motor. It describes 28 steps to disassemble the various components of the travel motor, including removing the head assembly, housing assembly, brake piston, friction discs, rotating group, pistons, and other internal parts. Detailed illustrations are provided to accompany each step of the disassembly process. Safety notices are included throughout to warn of potential hazards like released spring forces.
1. The document provides instructions for removing and installing final drives on 320-series excavators. It describes disconnecting hydraulic lines, removing mounting bolts, and using lifting tools to remove the final drives from the excavator.
2. Detailed steps are given for disassembling the final drives, including removing gears, carriers, seals, and other components. Alignment marks should be made for reassembly.
3. Reassembly involves cleaning parts, applying threadlock and lubricant, and torquing bolts to specification. Seals and bearings must be installed correctly to prevent damage.
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. Key steps include:
1. Using tooling to compress the valve spring and rotate the crankshaft to allow the piston to hold the valve open while the spring is removed.
2. Removing the valve keepers and spring retainer to access the valve spring.
3. Reversing the process to install new valve springs, making sure to complete installation on pairs of cylinders before moving to the next pair.
Caterpillar cat 320 d l excavator (prefix a9f) service repair manual (a9f0000...fikskkdmmd1
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. The removal process involves using specialized tools to compress the valve springs so the valves can be serviced while keeping the piston at top dead center. Installation requires cleaning components, lubricating the valves, and using tools to carefully compress the springs into place. Proper assembly procedure and safety precautions are emphasized to avoid injury from the force of the compressed springs.
Caterpillar cat 320 d excavator (prefix kgf) service repair manual (kgf00001 ...fikskkdmmd1
This document provides instructions for disassembling and assembling the travel motor of a 320D L excavator. The disassembly process includes 27 steps to remove components like the head, fittings, seals, brake piston, plates, and barrel assembly. The assembly section outlines 13 steps including installing seals, keys, cam plate, springs, and piston shoe assemblies back into the barrel assembly and body of the travel motor. Special care must be taken to align parts properly and not allow other components to come apart during the process.
Caterpillar cat 320 d excavator (prefix dhk) service repair manual (dhk00001 ...fikskkdmmd1
This document provides instructions for removing and installing a boom cylinder on a 320D excavator. It includes:
1) Detailed steps to remove the boom cylinder such as releasing hydraulic pressure, removing mounting bolts and pins, and lifting the cylinder off the machine.
2) Information on required tools and torque specifications for reassembly.
3) The installation procedure which describes mounting the cylinder back onto the excavator and reinstalling all mounting hardware.
Safety warnings are provided to relieve hydraulic pressure before disassembling cylinders. The document contains diagrams illustrating each step in the process.
Caterpillar cat 320 track type excavator (prefix 2 dl) service repair manual ...fikskkdmmd1
This document provides instructions for removing and installing valve stem seals on Caterpillar 320, 320L, and 320N track-type excavators. The procedure involves using a seal pick tool to remove the old seals from the valve guides and install new seals. Technicians are instructed to keep all parts clean and coat the new seals with engine oil during installation.
Caterpillar cat 320 s excavator (prefix 3 xk) service repair manual (3xk00822...fikskkdmmd1
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 320 excavator models. The removal procedure involves disconnecting tubes, removing clips and pins connecting the governor. Installation requires applying lubricant to seals, connecting the governor with pins and clips, and reinstalling the fuel injection control linkage using bolts. Tools including special pliers and pins are required. Referenced documents provide additional guidance on inspection and adjustment.
Caterpillar cat 320 n excavator (prefix 4 zj) service repair manual (4zj00460...fikskkdmmd1
1. The document provides instructions for removing and installing final drives on 320-series excavators. It describes disconnecting hydraulic lines, removing mounting bolts, and using hoists to lift heavy components like the final drive, ring gear, and carrier assemblies.
2. Detailed steps are given for disassembling the final drive components, including removing planetary gears, sun gears, and thrust washers. Special tools are required for removing retaining rings. Identification marks should be made on parts for reassembly.
3. Reassembly requires applying threadlock to bolts and anti-seize compound to bearings. Proper shim thickness must be determined to set bearing preload. Duo-Cone seals must be installed
Caterpillar cat 320 l excavator (prefix 4 zj) service repair manual (4zj00460...fikskkdmmd1
This document provides instructions for removing and installing final drives on 320-series excavators. It outlines the steps to release hydraulic pressure, remove the final drive housing, and disassemble/reassemble the internal components. The process involves removing 20 bolts, hydraulic lines, and using lifting tools to maneuver heavy internal parts like carriers, gears, and housings weighing up to 82 kg. Proper cleaning, lubrication, and torque specifications are noted to ensure correct reassembly.
Caterpillar cat 320 l excavator (prefix 3 xk) service repair manual (3xk00822...fikskkdmmd1
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 320 excavator models. It describes the required tools and gives a step-by-step process including removing clips and pins, sliding tubes, and removing/installing parts like the governor, linkage, and seals using special tools. References are provided for more information on governors and linkage inspection procedures.
Caterpillar cat 304.5 mini hydraulic excavator (prefix anr) service repair ma...fjsjekdmmeme
The document provides instructions for disassembling and assembling a piston pump. It lists 34 steps for disassembling the pump, removing components like the piston, valve, plates, seals and bearings. It then lists 32 steps for assembling the pump, installing the components in reverse order and ensuring new seals and O-rings are used. Cleanliness is emphasized throughout to prevent contaminants from entering the system. Tools including snap ring pliers are required.
Caterpillar cat 303.5 e2 mini hydraulic excavator (prefix jwy) service repair...fjsjekdmmeme
The document provides instructions for removing and installing inlet and exhaust valves, valve springs, valve guides, and valve seat inserts on a Caterpillar 303.5E2 Mini Hydraulic Excavator engine. The procedures describe using various tools to compress valve springs, remove components in the proper sequence while keeping them clean, and reinstalling components in the reverse order of removal. Special tools and trained personnel are required for some tasks like removing valve guides and seats.
Caterpillar cat 303 cr mini hydraulic excavator (prefix dma) service repair m...fjsjekdmmeme
This document provides assembly instructions for the main control valve of a 303 CR Mini Hydraulic Excavator. It describes assembling 8 different block assemblies (L through H) that make up the main control valve. The instructions note that cleanliness is important, valves must be assembled in the same configuration, and components must be returned to their original valves. Personal injury warnings are also provided regarding spring forces.
Caterpillar cat 320 l track type excavator (prefix 2dl) service repair manual...fkjsekksmem
This document provides instructions for servicing components of Caterpillar excavator models 320, 320L, and 320N, including:
- Removing and installing inlet and exhaust valve seals
- Removing the engine oil filter base
- Installing the engine oil filter base
- Removing the engine oil cooler
- Disassembling the engine oil cooler
- Reassembling the engine oil cooler
- Installing the engine oil cooler
The document includes diagrams and step-by-step instructions for maintenance procedures. Technicians are advised to keep components clean and contain fluids properly during repair.
Caterpillar cat 329 e excavator (prefix pty) service repair manual (pty00001 ...fkjsekksmem
The document provides instructions for removing and installing components related to the crankshaft on a Caterpillar 329E excavator engine, including:
- Removing and installing the vibration damper and pulley, which involves removing screws and installing guide studs.
- Removing and installing the crankshaft front seal using a removal/installation tool.
- Removing and installing the front cover, which requires identifying bolt positions, cleaning surfaces, and installing a new gasket.
Caterpillar cat 311 c excavator (prefix cke) service repair manual (cke00001 ...fjskefkemms
This service repair manual provides instructions for removing and installing inlet and exhaust valve seals on models 311C and 311C U excavators. The procedures describe using a seal pick tool to remove old seals from valve guides and installing new seals. Safety notices are included to keep parts clean and contain fluids.
Caterpillar cat 305 cr mini hydraulic excavator (prefix dgt) service repair m...fjskekfseik
The document provides instructions for removing the swivel on a 305CR Mini Hydraulic Excavator. It lists the required tools and notes to release hydraulic pressure and remove the cab first. The procedure involves using plugs and caps to seal ports while removing 4 bolts to detach the swivel assembly.
Caterpillar cat m316 d wheeled excavator (prefix w6a) service repair manual (...fujsjefjwerkskemm
This document provides instructions for removing and installing an idler gear on a Caterpillar C6.6 engine. It describes the required tools and steps to:
1) Lock the camshaft and crankshaft in position, remove bolts, and remove the standard or heavy-duty idler gear.
2) Clean and inspect the idler gear components, install the idler gear while aligning timing marks, install bolts, and check end play and backlash.
3) Ensure the number one piston is at top dead center before installing the idler gear in the correct position and alignment.
Caterpillar cat 320 d l excavator (prefix kgf) service repair manual (kgf0000...fkjsekksmem
This document provides instructions for disassembling and assembling the travel motor of a 320D L excavator. The disassembly process includes 27 steps to remove components like the head, fittings, seals, brake piston, plates, and barrel assembly. The assembly section outlines 13 steps including installing seals, keys, cam plate, springs, and piston shoe assemblies back into the barrel assembly and body of the travel motor. Special care must be taken to align parts properly and not allow components to separate during disassembly and assembly.
Caterpillar cat 302.5 mini hydraulic excavator (prefix 4 az) service repair m...fjsjekdmmeme
1) The document provides instructions for removing and installing the fuel injection pump, exhaust manifold, and inlet manifold on a 302.5 Mini Hydraulic Excavator powered by a 3013 engine.
2) To remove the fuel injection pump, disconnect lines and solenoids, remove mounting bolts and nuts, and record shim thickness. To install, position shims and pump, reconnect links, and tighten bolts.
3) Exhaust manifold removal involves removing nuts, bolts and gasket. Installation requires cleaning surfaces, installing new gasket, and tightening bolts.
4) Inlet manifold removal requires removing bolts, gaskets and spacer plate. Installation involves cleaning
Caterpillar cat 304.5 mini hydraulic excavator (prefix wak) service repair ma...fjskekfseik
This document provides instructions for removing the swing motor from a 304.5 Mini Hydraulic Excavator. The instructions include releasing hydraulic system pressure, removing the cab and seat, disconnecting linkages from the left console, and removing bolts to separate the right console to access the swing motor for removal. Proper containment of fluids and marking of disconnected lines and fittings is emphasized.
Caterpillar cat 330 f excavator (prefix lbn) service repair manual (lbn00001 ...fjskekdmjekm
The document provides instructions for disassembling a 330F LN excavator travel motor. It describes 28 steps to disassemble the various components of the travel motor, including removing the head assembly, housing assembly, brake piston, friction discs, rotating group, pistons, and other internal parts. Detailed illustrations are provided to accompany each step of the disassembly process. Safety notices are included throughout to warn of potential hazards like released spring forces.
1. The document provides instructions for removing and installing final drives on 320-series excavators. It describes disconnecting hydraulic lines, removing mounting bolts, and using lifting tools to remove the final drives from the excavator.
2. Detailed steps are given for disassembling the final drives, including removing gears, carriers, seals, and other components. Alignment marks should be made for reassembly.
3. Reassembly involves cleaning parts, applying threadlock and lubricant, and torquing bolts to specification. Seals and bearings must be installed correctly to prevent damage.
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. Key steps include:
1. Using tooling to compress the valve spring and rotate the crankshaft to allow the piston to hold the valve open while the spring is removed.
2. Removing the valve keepers and spring retainer to access the valve spring.
3. Reversing the process to install new valve springs, making sure to complete installation on pairs of cylinders before moving to the next pair.
Caterpillar cat 320 d l excavator (prefix a9f) service repair manual (a9f0000...fikskkdmmd1
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. The removal process involves using specialized tools to compress the valve springs so the valves can be serviced while keeping the piston at top dead center. Installation requires cleaning components, lubricating the valves, and using tools to carefully compress the springs into place. Proper assembly procedure and safety precautions are emphasized to avoid injury from the force of the compressed springs.
Caterpillar cat 320 d excavator (prefix kgf) service repair manual (kgf00001 ...fikskkdmmd1
This document provides instructions for disassembling and assembling the travel motor of a 320D L excavator. The disassembly process includes 27 steps to remove components like the head, fittings, seals, brake piston, plates, and barrel assembly. The assembly section outlines 13 steps including installing seals, keys, cam plate, springs, and piston shoe assemblies back into the barrel assembly and body of the travel motor. Special care must be taken to align parts properly and not allow other components to come apart during the process.
Caterpillar cat 320 d excavator (prefix dhk) service repair manual (dhk00001 ...fikskkdmmd1
This document provides instructions for removing and installing a boom cylinder on a 320D excavator. It includes:
1) Detailed steps to remove the boom cylinder such as releasing hydraulic pressure, removing mounting bolts and pins, and lifting the cylinder off the machine.
2) Information on required tools and torque specifications for reassembly.
3) The installation procedure which describes mounting the cylinder back onto the excavator and reinstalling all mounting hardware.
Safety warnings are provided to relieve hydraulic pressure before disassembling cylinders. The document contains diagrams illustrating each step in the process.
Caterpillar cat 320 track type excavator (prefix 2 dl) service repair manual ...fikskkdmmd1
This document provides instructions for removing and installing valve stem seals on Caterpillar 320, 320L, and 320N track-type excavators. The procedure involves using a seal pick tool to remove the old seals from the valve guides and install new seals. Technicians are instructed to keep all parts clean and coat the new seals with engine oil during installation.
Caterpillar cat 320 s excavator (prefix 3 xk) service repair manual (3xk00822...fikskkdmmd1
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 320 excavator models. The removal procedure involves disconnecting tubes, removing clips and pins connecting the governor. Installation requires applying lubricant to seals, connecting the governor with pins and clips, and reinstalling the fuel injection control linkage using bolts. Tools including special pliers and pins are required. Referenced documents provide additional guidance on inspection and adjustment.
Caterpillar cat 320 n excavator (prefix 4 zj) service repair manual (4zj00460...fikskkdmmd1
1. The document provides instructions for removing and installing final drives on 320-series excavators. It describes disconnecting hydraulic lines, removing mounting bolts, and using hoists to lift heavy components like the final drive, ring gear, and carrier assemblies.
2. Detailed steps are given for disassembling the final drive components, including removing planetary gears, sun gears, and thrust washers. Special tools are required for removing retaining rings. Identification marks should be made on parts for reassembly.
3. Reassembly requires applying threadlock to bolts and anti-seize compound to bearings. Proper shim thickness must be determined to set bearing preload. Duo-Cone seals must be installed
Caterpillar cat 320 l excavator (prefix 4 zj) service repair manual (4zj00460...fikskkdmmd1
This document provides instructions for removing and installing final drives on 320-series excavators. It outlines the steps to release hydraulic pressure, remove the final drive housing, and disassemble/reassemble the internal components. The process involves removing 20 bolts, hydraulic lines, and using lifting tools to maneuver heavy internal parts like carriers, gears, and housings weighing up to 82 kg. Proper cleaning, lubrication, and torque specifications are noted to ensure correct reassembly.
Caterpillar cat 320 l excavator (prefix 3 xk) service repair manual (3xk00822...fikskkdmmd1
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 320 excavator models. It describes the required tools and gives a step-by-step process including removing clips and pins, sliding tubes, and removing/installing parts like the governor, linkage, and seals using special tools. References are provided for more information on governors and linkage inspection procedures.
The document provides instructions for disassembling and assembling the travel motor of a 320 GC excavator. It lists the required tools and parts. The disassembly process involves removing plugs and seals from the motor housing. Springs must be released carefully due to risk of injury. The brake piston is then unseated using air pressure before internal components of the motor can be accessed and replaced. The assembly procedure reverses the disassembly steps.
This service repair manual provides instructions for installing a flywheel and crankshaft rear seal on a Caterpillar C4.4 engine. It outlines the required tools and steps to remove and install the flywheel housing. The procedures include inspecting parts for leaks, aligning seals and gaskets, and torquing bolts to the specified values.
This document provides instructions for removing and installing final drives on 320-series excavators. It outlines the steps to release hydraulic pressure, remove the final drive housing, and disassemble/reassemble the internal components. The process involves removing 20 bolts, hydraulic lines, and using lifting tools to maneuver heavy internal parts like carriers, gears, and housings weighing up to 82 kg. Proper cleaning, lubrication, and torque specifications are noted to ensure correct reassembly.
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 320 excavator models. It describes the required tools and gives a step-by-step process including removing clips and pins, sliding tubes, and removing/installing parts like the governor, linkage, and seals using special tools. References are provided for more information on governors and linkage inspection procedures.
Caterpillar cat 305 e2cr mini hydraulic excavator (prefix pyr) service repair...fikskkdmmd1
The document provides instructions for servicing various components of a Caterpillar 305E2 CR mini hydraulic excavator engine. It describes procedures for removing and installing components like the idler gear, front housing, valve mechanism cover, rocker shaft and push rods. The steps include using proper tooling, alignment marks, torque specifications and cleaning/lubricating parts.
Caterpillar cat 305 e2 cr mini hydraulic excavator (prefix djx) service repai...fikskkdmmd1
This document provides instructions for removing and installing various engine components on a 305E2 CR Mini Hydraulic Excavator including:
- Crankshaft rear seal
- Flywheel housing
- Crankshaft pulley
- Crankshaft front seal
- Idler gear
The procedures include illustrations and describe using various tools to disassemble, clean, inspect, and reinstall each component according to the specified instructions and torque specifications.
Caterpillar cat 305 e2 cr mini hydraulic excavator (prefix df5) service repai...fikskkdmmd1
The document provides instructions for removing and installing various components of a 305E2 CR Mini Hydraulic Excavator engine, including the fuel injection lines, exhaust gas recirculation cooler, fuel injection pump, electronic unit injector, and turbocharger. Safety precautions are outlined that must be followed when working on fuel system and high temperature components.
Caterpillar cat 305 e2 cr mini hydraulic excavator (prefix bz5) service repai...fikskkdmmd1
This document provides instructions for removing and installing various components of a 305E2 CR Mini Hydraulic Excavator engine, including:
- Removing the fuel manifold by removing bolts and lines, taking care not to damage sensors.
- Removing fuel injection lines by disconnecting hoses and tubes after capping lines to prevent contamination.
- Removing the exhaust gas recirculation cooler by draining coolant and removing hoses and mounting brackets.
- Removing the fuel injection pump by disconnecting lines and hoses and removing nuts and bolts.
- Removing electronic unit injectors by disconnecting hoses after taking safety precautions for the high pressure fuel system.
Caterpillar cat 305 cr mini hydraulic excavator (prefix dsa) service repair m...fikskkdmmd1
The document provides instructions for removing and disassembling the travel motor from a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing the track and final drive sprocket. Disassembly involves removing plates, barrels, pistons, springs, gears and other components using various tools. Detailed steps and illustrations are provided to label parts and ensure correct reassembly.
Caterpillar cat 305 cr mini hydraulic excavator (prefix dgt) service repair m...fikskkdmmd1
The document provides instructions for removing the swivel on a 305CR Mini Hydraulic Excavator. The steps include:
1. Releasing hydraulic system pressure and removing the cab.
2. Disconnecting and plugging multiple hose assemblies connected to the swivel.
3. Removing bolts and a plate from the bottom of the carbody.
Caterpillar cat 305 c cr mini hydraulic excavator (prefix hwj) service repair...fikskkdmmd1
The document provides instructions for disassembling and inspecting various engine components of a 305C CR Mini Hydraulic Excavator, including the timing gear, camshaft, oil pan, piston, connecting rod, crankshaft, and cylinder block. It lists the components in their disassembly sequence and provides illustrations and instructions for removing each part. Tolerances and limits are provided for measuring various components like gear backlash, end play, and clearance.
Caterpillar cat 305.5 e2cr mini hydraulic excavator (prefix shw) service repa...fikskkdmmd1
The document provides instructions for removing and installing various engine components on a Caterpillar 305.5E2CR mini hydraulic excavator powered by a C2.4 engine. The components include the idler gear, front housing, valve mechanism cover, rocker shaft and push rods, and disassembling the rocker shaft. The procedures note required tools, removal steps, installation steps including torque specifications and lubrication points.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320 L EXCAVATOR 3XK
Configuration: 320, 320 L, 320 N AND 320 S EXCAVATORS 3XK00822-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01928381
Governor - Remove
SMCS - 1264-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 136-4149 Governor Pliers(1)
1
(1)
This tool is part of the 128-8822 Fuel System and Governor Tool Group.
Start By:
a. Remove the fuel shutoff solenoid. Refer to Disassembly and Assembly, "Fuel Shutoff
Solenoid - Remove and Install".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/5(W)
w
2019/12/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
3. Illustration 1 g00613041
1. Disconnect the governor control cable.
2. Remove oil tube assembly (1). Remove tube assembly (2) and tube assembly for fuel ratio
control (3), if equipped. Plug and cap all connections.
Illustration 2 g00613071
3. Remove clip (4).
2/5(W)
w
2019/12/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
4. Illustration 3 g00655975
4. Use Tooling (A) to slide tube assembly (5) into the cylinder head.
Illustration 4 g00613149
5. Remove the clip and use Tooling (A) to remove the clevis pin (6).
Note: Clevis pin (6) must stay with the governor in order to be adjusted.
3/5(W)
w
2019/12/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
5. Illustration 5 g00613563
6. Remove bolts (7) and the washers that hold the governor in position.
Illustration 6 g00673182
7. Remove the governor from the engine.
Illustration 7 g00673180
8. Remove O-ring seal (3) on the governor.
Illustration 8 g00672742
4/5(W)
w
2019/12/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
6. 9. Remove the O-ring seal and tube assembly (5) from the cylinder head.
Illustration 9 g00672733
10. Remove O-ring seal (2) on the tube assembly (5).
Illustration 10 g00673178
11. Remove O-ring seal (1) from the cylinder head.
Note: For more information on the governor, refer to Service Manual, SENR6454, "3114, 3116, &
3126 Engine Governors". The Service Manual, SENR6454 requires the use of a 1U-7326
Governor Calibration Bench. For information on reusability of components in the governor, refer
to Guideline For Reusable Parts And Salvage Operations, SEBF8434, "3100 Governor Inspection
and General Information for Mechanical Governor Groups Used in 3114, 3116, and 3126 Engines
Equipped with Mechanical Unit Injectors (MUI)".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Dec 29 15:10:10 UTC+0800 2019
5/5(W)
w
2019/12/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
7. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320 L EXCAVATOR 3XK
Configuration: 320, 320 L, 320 N AND 320 S EXCAVATORS 3XK00822-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01928419
Governor - Install
SMCS - 1264-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 136-4149 Governor Pliers(1)
1
B
128-8827 Pin(1)
1
1U-7523 Pin Pilot(1)
1
(1)
This tool is part of the 128-8822 Governor Tool Group.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For more information on the governor, refer to Service Manual, SENR6454, "3114, 3116, &
3126 Engine Governors". The Service Manual, SENR6454 requires the use of a 1U-7326
Governor Calibration Bench. For information on reusability of components in the governor, refer
to Guideline For Reusable Parts And Salvage Operations, SEBF8434, "3100 Governor Inspection
and General Information for Mechanical Governor Groups Used in 3114, 3116, and 3126 Engines
Equipped with Mechanical Unit Injectors (MUI)".
1/5(W)
w
2019/12/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
8. Illustration 1 g00673178
1. Apply lubricant to the new O-ring seal (1). Install new O-ring seal (1) in the cylinder head.
Illustration 2 g00672733
2. Apply lubricant to the new O-ring seal (2). Install new O-ring seal (2) on the tube assembly
(5).
Illustration 3 g00672742
3. Install the O-ring seal and tube assembly (5) in the cylinder head.
2/5(W)
w
2019/12/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
9. Illustration 4 g00673180
4. Apply lubricant to the new O-ring seal (3). Install new O-ring seal (3) on the governor.
Illustration 5 g00673182
5. Place the governor in position on the engine.
Illustration 6 g00613563
6. Install the washers and bolts (7) that hold the governor in place.
3/5(W)
w
2019/12/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
10. Illustration 7 g00672755
7. Install clevis pin (6) in Tooling (B).
Illustration 8 g00672752
8. Use Tooling (B) to install clevis pin (6) and the clip.
9. Check the fuel setting adjustment. Refer to Testing and Adjusting, SENR5118.
4/5(W)
w
2019/12/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
11. Illustration 9 g00655975
10. Use Tooling (A) to slide tube assembly (5) into the governor.
Illustration 10 g00613071
11. Install clip (4).
Illustration 11 g00613041
12. Install oil tube assembly (1). Install tube assembly (2) and tube assembly for fuel ratio
control (3), if equipped. Plug and cap all connections.
13. Install the governor control cable.
End By:
a. Install the fuel shutoff solenoid. Refer to Disassembly and Assembly, "Fuel Shutoff
Solenoid - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Dec 29 15:11:06 UTC+0800 2019
5/5(W)
w
2019/12/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320 L EXCAVATOR 3XK
Configuration: 320, 320 L, 320 N AND 320 S EXCAVATORS 3XK00822-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01928445
Fuel Injection Control Linkage - Remove
SMCS - 1298-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 136-4149 Governor Pliers 1
Start By:
a. Remove the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrod - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3(W)
w
2019/12/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
13. Illustration 1 g00613071
1. Remove clip (4). Clip (4) is located between the governor and the cylinder head.
Illustration 2 g00655975
2. Use Tooling (A) to slide tube assembly (5) into the cylinder head.
Illustration 3 g00613149
2/3(W)
w
2019/12/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
14. 3. Remove the clip and use Tooling (A) to remove the clevis pin (6). Clevis pin (6) connects
the governor to the control lever of the fuel injection control linkage.
Note: Clevis pin (6) must stay with the governor in order to be adjusted.
Illustration 4 g00630566
4. Remove bolts (1) and remove fuel injection control linkage (2). Control lever (3) connects
the fuel injection control linkage (2) to the governor.
Note: For information on the inspection procedure for control lever (3), refer to Special
Instruction, REHS0601, "Inspection and Modification of the 102-7459 Fuel Injection
Control Linkage and the 4P-9048 Fuel Injection Control Linkage".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Dec 29 15:12:01 UTC+0800 2019
3/3(W)
w
2019/12/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320 L EXCAVATOR 3XK
Configuration: 320, 320 L, 320 N AND 320 S EXCAVATORS 3XK00822-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines, IT18F
Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01928573
Fuel Injection Control Linkage - Install
SMCS - 1298-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 136-4149 Governor Pliers(1)
1
B
128-8827 Pin(1)
1
1U-7523 Pin Pilot(1)
1
C 1U-6675 Spring Compressor(1)
6
D 128-8822 Fuel System and Governor Tool Gp 1
(1)
This tool is part of the 128-8822 Governor Tool Group.
1/4(W)
w
2019/12/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
16. Illustration 1 g00661331
Note: For information on the inspection procedure for control lever (3), refer to Special Instruction,
REHS0601, "Inspection and Modification of the 102-7459 Fuel Injection Control Linkage and the 4P
-9048 Fuel Injection Control Linkage".
1. Loosen setscrews (4) on each bracket.
2. Install fuel control linkage (2) and install bolts (1). Use the following sequence in order to tighten the
bolts.
3. Tighten bracket (A) and (D) to a torque of 12 ± 3 N·m (106 ± 27 lb in).
4. Tighten brackets (B) and (C) to a torque of 12 ± 3 N·m (106 ± 27 lb in).
5. Position brackets (B) and (C) in order to allow free rotation of the fuel control rod.
6. Use a 2.5 mm (0.10 inch) wrench to tighten setscrews (4). Tighten the setscrews to a torque of
3.5 ± 0.2 N·m (31 ± 2 lb in). Do not overtighten the setscrews. Ensure that the control rod rotates
freely.
7. The control rod should rotate freely when a force of 4.4 N (1 lb) or less is applied to control lever
(3).
Illustration 2 g00750163
8. Rotate the unit injectors in order to engage the injector rack bar (5) with the fuel injection control
linkage (2).
Note: If the unit injectors are not installed, refer to the Disassembly and Assembly, "Unit Injector -
Install".
2/4(W)
w
2019/12/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
17. 9. Install Tooling (C) on the unit injectors and compress the springs.
Note: For the procedure to install Tooling (C), refer to Tool Operating Manual, NEHS0610, "Using
the 128-8822 Tool Group on 3114, 3116, and 3126 Engines with Mechanical Unit Injectors (MUI)".
Illustration 3 g00672755
10. Install clevis pin (6) in Tooling (B). Clevis pin (6) attaches the control lever (3) to the governor.
Illustration 4 g00672752
11. Use Tooling (B) to install clevis pin (6) and the clip.
12. Use Tooling (D) to set the unit injector synchronization.
Note: For the procedure to use Tooling (D), refer to Tool Operating Manual, NEHS0610, "Using the
128-8822 Tool Group on 3114, 3116, and 3126 Engines with Mechanical Unit Injectors (MUI)".
13. Remove Tooling (C) from the unit injectors.
3/4(W)
w
2019/12/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
18. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
19. Illustration 5 g00655975
14. Use Tooling (A) to slide tube assembly (5) into the governor.
Illustration 6 g00613071
15. Install clip (4).
End By:
a. Install the rocker arm assemblies and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrod - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Dec 29 15:12:57 UTC+0800 2019
4/4(W)
w
2019/12/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320 L EXCAVATOR 3XK
Configuration: 320, 320 L, 320 N AND 320 S EXCAVATORS 3XK00822-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i05919358
Unit Injector - Remove
SMCS - 1290-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-0302 Bar 1
Start By:
A. Remove the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrod - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/3(W)
w
2019/12/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
21. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00775441
2/3(W)
w
2019/12/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
22. Illustration 2 g00625237
1. Remove fuel injector hold-down bolt (1) .
Note: Do not pry on the injector hold-down bracket. Damage to the unit injector could
occur. The unit injector has a notch on the opposite side of the rack. This notch is used for
prying the unit injector loose. Some fuel injector racks move freely when the spring is not
compressed. Do not move the fuel injector rack without compressing the fuel injector spring
slightly. Damage may occur to the unit injector.
2. Use Tooling (A) to loosen the unit injector. Rotate the unit injector in order to disengage
injector rack bar (3) from fuel injection control linkage (2) .
3. Remove the unit injector. Ensure that two O-ring seals are on the unit injector.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Dec 29 15:13:53 UTC+0800 2019
3/3(W)
w
2019/12/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...