This document provides service and repair instructions for the final drive and related components of a 316F L excavator. It includes specifications, illustrations, removal and disassembly procedures, and assembly instructions. The procedures involve using various tools to remove, disassemble, and replace components like gears, bearings, seals, and housings. Precautions are outlined for cleaning parts and applying lubricants and sealants during assembly.
Caterpillar cat 329 d l excavator (prefix bfc) service repair manual (bfc0000...ufdjjsjefkkkemm
1) The document provides instructions for servicing the transmission of a 329D L and 329D LN excavator by removing and disassembling the final drive, then reassembling it.
2) 37 steps are outlined for disassembly, which include removing gears, shafts, seals, and other components using various tools.
3) 35 steps are provided for reassembly, including pressing in bearings, measuring clearances, installing seals and pins, and refitting components in reverse order of disassembly. Cleanliness and applying lubricants are emphasized throughout.
Caterpillar cat 329 d excavator (prefix yfw) service repair manual (yfw00001 ...fkjsekksmem
This document provides instructions for disassembling and assembling the final drive of a 329D or 329D L excavator. It lists 37 steps for disassembly, removing components like gears, shafts, bearings and seals. The assembly section outlines 15 steps, including pressing bearings into place, installing seals, and using shims to set the proper bearing preload when mounting the main housing onto the motor housing. Cleanliness is emphasized throughout as important for preventing contamination.
Caterpillar cat 323 e l excavator (prefix yrp) service repair manual (yrp0000...fjskefkemms
This document provides instructions for servicing the final drive of excavator models 323E L, 323E LN, and 323E SA. It includes procedures for disassembling and removing components like the final drive, carrier assembly, ring gears, and seals. It also provides instructions for reassembling these components, including installing seals, bearings, and gears, and using shims to set proper bearing preload. Bolts and seals must be tightened to the specified torques.
Caterpillar cat 365 b ii excavator (prefix der) service repair manual (der000...fios9dkksd
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. Key steps include:
1. Disassembling the final drive by removing gears, bearings, seals and housing components using various tools.
2. Determining the correct shim thickness for reassembly by measuring gear dimensions under precise loading conditions.
3. Reassembling the components in reverse order, applying anti-seize compound and torque sealant, and ensuring proper installation of seals between housings.
Caterpillar cat 323 e l excavator (prefix rap) service repair manual (rap0000...fjskefkemms
The document provides instructions for servicing the final drive of excavator models 323E L, 323E LN, and 323E SA. It includes steps to disassemble and remove the final drive components, such as the carrier assembly, ring gears, planetary gears, and seals. It also provides instructions for assembling the final drive, including pressing bearings into place, determining the correct shim thickness, installing seals and pins, and reassembling the carrier assembly. Tools required include lifting devices, presses, seal installers, and other specialized tools. Proper torque values and procedures are specified for reinstalling components.
Caterpillar cat 319 d l excavator (prefix zca) service repair manual (zca0000...fjkskedmme
This document provides assembly instructions for a final drive on an excavator model 319D L. It involves 37 steps including installing bearings, seals, gears, and other components into housings and covers. Precise measurements and torque specifications are required. Cleanliness is important throughout the process. The completed final drive and sprocket assembly weighs approximately 310 kg.
Caterpillar cat 14 m3 motor grader (prefix n9s) service repair manual (n9s000...fjsekdmmeed
This document provides disassembly instructions for the rear axle, differential, and final drive of a 14M3 motor grader. It lists 51 steps to fully disassemble these components, including removing sprockets, bearings, seals, housings, gears, and other parts. Various tools are required, and weights of removed parts are provided. Detailed illustrations accompany each step to show how to properly disassemble the power train.
Caterpillar cat 385 c l excavator (prefix sbe) service repair manual (sbe0000...fjkskedmme
This document provides instructions for disassembling and assembling the final drive of a 385C L Excavator. It lists the required tools and gives step-by-step instructions to remove components such as the housing cover, carrier assemblies, planetary gear assemblies, ring gear, and motor housing. Precautions are given to ensure cleanliness during disassembly and assembly. The parts are to be reinstalled in their original locations and orientation marks should be made for alignment. Proper lifting devices and techniques are specified due to the heavy weights of some components.
Caterpillar cat 329 d l excavator (prefix bfc) service repair manual (bfc0000...ufdjjsjefkkkemm
1) The document provides instructions for servicing the transmission of a 329D L and 329D LN excavator by removing and disassembling the final drive, then reassembling it.
2) 37 steps are outlined for disassembly, which include removing gears, shafts, seals, and other components using various tools.
3) 35 steps are provided for reassembly, including pressing in bearings, measuring clearances, installing seals and pins, and refitting components in reverse order of disassembly. Cleanliness and applying lubricants are emphasized throughout.
Caterpillar cat 329 d excavator (prefix yfw) service repair manual (yfw00001 ...fkjsekksmem
This document provides instructions for disassembling and assembling the final drive of a 329D or 329D L excavator. It lists 37 steps for disassembly, removing components like gears, shafts, bearings and seals. The assembly section outlines 15 steps, including pressing bearings into place, installing seals, and using shims to set the proper bearing preload when mounting the main housing onto the motor housing. Cleanliness is emphasized throughout as important for preventing contamination.
Caterpillar cat 323 e l excavator (prefix yrp) service repair manual (yrp0000...fjskefkemms
This document provides instructions for servicing the final drive of excavator models 323E L, 323E LN, and 323E SA. It includes procedures for disassembling and removing components like the final drive, carrier assembly, ring gears, and seals. It also provides instructions for reassembling these components, including installing seals, bearings, and gears, and using shims to set proper bearing preload. Bolts and seals must be tightened to the specified torques.
Caterpillar cat 365 b ii excavator (prefix der) service repair manual (der000...fios9dkksd
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. Key steps include:
1. Disassembling the final drive by removing gears, bearings, seals and housing components using various tools.
2. Determining the correct shim thickness for reassembly by measuring gear dimensions under precise loading conditions.
3. Reassembling the components in reverse order, applying anti-seize compound and torque sealant, and ensuring proper installation of seals between housings.
Caterpillar cat 323 e l excavator (prefix rap) service repair manual (rap0000...fjskefkemms
The document provides instructions for servicing the final drive of excavator models 323E L, 323E LN, and 323E SA. It includes steps to disassemble and remove the final drive components, such as the carrier assembly, ring gears, planetary gears, and seals. It also provides instructions for assembling the final drive, including pressing bearings into place, determining the correct shim thickness, installing seals and pins, and reassembling the carrier assembly. Tools required include lifting devices, presses, seal installers, and other specialized tools. Proper torque values and procedures are specified for reinstalling components.
Caterpillar cat 319 d l excavator (prefix zca) service repair manual (zca0000...fjkskedmme
This document provides assembly instructions for a final drive on an excavator model 319D L. It involves 37 steps including installing bearings, seals, gears, and other components into housings and covers. Precise measurements and torque specifications are required. Cleanliness is important throughout the process. The completed final drive and sprocket assembly weighs approximately 310 kg.
Caterpillar cat 14 m3 motor grader (prefix n9s) service repair manual (n9s000...fjsekdmmeed
This document provides disassembly instructions for the rear axle, differential, and final drive of a 14M3 motor grader. It lists 51 steps to fully disassemble these components, including removing sprockets, bearings, seals, housings, gears, and other parts. Various tools are required, and weights of removed parts are provided. Detailed illustrations accompany each step to show how to properly disassemble the power train.
Caterpillar cat 385 c l excavator (prefix sbe) service repair manual (sbe0000...fjkskedmme
This document provides instructions for disassembling and assembling the final drive of a 385C L Excavator. It lists the required tools and gives step-by-step instructions to remove components such as the housing cover, carrier assemblies, planetary gear assemblies, ring gear, and motor housing. Precautions are given to ensure cleanliness during disassembly and assembly. The parts are to be reinstalled in their original locations and orientation marks should be made for alignment. Proper lifting devices and techniques are specified due to the heavy weights of some components.
Caterpillar cat 140 k 2 motor grader (prefix szw) service repair manual (szw0...fusjefjskekmem
This document provides instructions for disassembling and assembling the final drive components of a 140K 2 Motor Grader. The disassembly process involves removing 24 separate components from the final drive housing. The assembly section outlines assembling the components in the reverse order and includes checking clearances with tools. Proper lubrication and heating of bearings is required during assembly.
Caterpillar cat 349 f l excavator (prefix wna) service repair manual (wna0000...fjjskekdmme
The document provides instructions for disassembling and assembling the travel motor of a 349F L and 352F excavator. It begins by describing the required tools and safety precautions. The 32-step disassembly procedure removes components like plugs, springs, pistons, and bearings. The assembly section provides specifications, required tools, and a 28-step procedure to reinstall components in reverse order. Precautions are given to lubricate parts and apply locking agents in correct locations.
Caterpillar cat 345 d l excavator (prefix kfh) service repair manual (kfh0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group on a C13 engine, including:
1. The procedure for removing the rear gear group involves removing 10 components and using 2 required tools.
2. The installation procedure involves 11 steps and uses 1 required tool, and includes instructions for properly installing and positioning bearings.
3. Separate sections provide procedures for removing and installing the flywheel and crankshaft rear seal. Precautions are mentioned regarding handling heated parts and containing fluids.
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then describes 28 steps to reassemble the final drive, including preloading the bearings, installing seals and pins, and reassembling the carrier assembly components. Cleanliness is emphasized throughout to prevent dirt from entering internal mechanisms during disassembly and assembly.
Caterpillar cat 374 d l excavator (prefix pas) service repair manual (pas0000...fjjskekdmme
This document provides instructions for disassembling and assembling the final drive of a 374D L excavator. It lists the required tools and presents 33 steps for disassembly, removing all internal components. It then outlines 37 steps for reassembly, starting with cleaning and inspecting parts, and continuing through installing bearings, seals, gears, and housing components in the reverse order of disassembly. Tolerances and special installation tools are specified to ensure proper bearing preload and sealing.
Caterpillar cat 345 d l excavator (prefix byc) service repair manual (byc0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group on a 345D L Excavator powered by a C13 engine, including:
1. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, gears, bushings, bearings, and covers.
2. Detailed installation instructions are also provided, including proper tooling, torque specifications, and ensuring correct dimensions and alignments of components.
3. Removal and installation of the flywheel and rear crankshaft seal are also described following similar procedures.
Caterpillar cat 345 d l excavator (prefix yee) service repair manual (yee0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group and crankshaft rear seal of a 345D L Excavator with a C13 engine. The removal procedure includes using various tools to remove bolts, seals, gears, bushings, and bearings. The installation procedure provides instructions on cleaning, inspecting, applying threadlock, and installing components while ensuring proper dimensions and alignments are met. Torque specifications and notes are provided throughout.
Caterpillar cat 345 d l excavator (prefix rgd) service repair manual (rgd0000...hhfjksekmm
This document provides instructions for disassembling and assembling the travel motor of a 345D L excavator. It lists 31 steps to fully disassemble the travel motor by removing components like the head, plates, seals, pins, brake piston, disks, and housing keys. Reassembly requires reversing the disassembly steps and ensuring parts are cleaned and placed back in their original locations and orientations. Special tools are listed to aid in removal and installation of components.
Caterpillar cat 319 d l excavator (prefix wbj) service repair manual (wbj0000...fjkskedmme
The document provides instructions for disassembling and assembling a final drive component of a 319D LN excavator. It includes 33 steps for disassembly, removing components like the cover, carrier assembly, ring gears, and seals. The assembly section has 13 steps, including preloading the bearings to determine the correct shim thickness, installing seals and pins, and attaching the main housing to the motor housing. Precise cleaning and use of replacement parts is emphasized throughout.
Caterpillar cat 325 d l excavator (prefix azp) service repair manual (azp0000...hfjsekekmmd
The document provides instructions for disassembling a service repair manual for excavator models 325D and 325D L. It lists required tools and a 33-step procedure that includes removing components like the final drive, cover, gears, seals, and housing pieces. Cleanliness is important during disassembly. Parts must be reinstalled in their original locations and lifting is required as component weights range from 30 to 688 pounds.
Caterpillar cat 14 m motor grader (prefix b9j) service repair manual (b9j0000...fjsekdmmeed
This document provides disassembly instructions for the rear axle, differential, and final drive of a 14M Motor Grader. It lists 50 steps to fully disassemble these components, including removing sprockets, gears, seals, bearings, and housings. Various tools are required, and safety precautions are provided. Detailed illustrations accompany each step to show how to position parts and which fasteners to remove. Component weights are listed to assist with lifting and handling.
Caterpillar cat 325 d l excavator (prefix dbh) service repair manual (dbh0000...hfjsekekmmd
The document provides instructions for disassembling a service repair manual for excavator models 325D and 325D L. It lists required tools and a multi-step process to disassemble the final drive. Key steps include removing the final drive cover, carrier assembly, ring gears, and other internal components. Cleanliness is important during disassembly to prevent dirt from entering mechanisms.
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves using various tools to remove 37 individual parts from the final drive assembly. The assembly process similarly uses tools to reinstall the parts in the reverse order, ensuring proper installation of seals and adjusting bearing preload through precise shimming.
Caterpillar cat 325 d excavator (prefix kbe) service repair manual (kbe00001 ...hfjsekekmmd
The document provides instructions for repairing the final drive of excavator models 325D and 325D L. It involves 14 steps including cleaning parts, applying lubricants, installing seals and bearings, adjusting bearing preload, and assembling components like the carrier assembly, planetary gears, and ring gear. Proper torque values and alignment of pins are emphasized throughout the process to ensure correct assembly.
Caterpillar cat 318 f l excavator (prefix fft) service repair manual (fft0000...fjkskedmme
This document provides disassembly instructions for the final drive of a 318F L excavator. It describes 41 steps to fully disassemble the final drive components. Key steps include removing the sprocket, pistons, barrel assembly, springs, and various seals and plates. Safety warnings are provided to release pressures and contain fluids safely.
Caterpillar cat 345 c excavator (prefix wde) service repair manual (wde00001 ...fjsekdmmeed
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. The disassembly procedure involves removing 28 parts in 28 steps, including removing the final drive cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure involves installing 29 parts in 29 steps in the reverse order, adjusting bearing preload using shims, and applying anti-seize compound and thread lock to ensure proper assembly. Tools such as retaining ring pliers, eyebolts, and a transmission stand are required.
Caterpillar Cat 316F L Excavator (Prefix ECZ) Service Repair Manual Instant D...kubei069369925
The document provides service repair instructions for a 316F L excavator final drive. It includes specifications, illustrations, and step-by-step procedures for removing, disassembling, and assembling the final drive. The removal procedure involves using lifting tools to detach the final drive from the frame. The disassembly procedure has 35 steps to fully take apart the internal components. Precautions are given to clean parts and apply sealants or lubricants during assembly. Required tools are listed for each procedure.
Caterpillar Cat 316F L Excavator (Prefix ECZ) Service Repair Manual Instant D...rishang96299
This document provides service and repair instructions for the final drive and related components of a 316F L excavator. It includes specifications, illustrations, removal and disassembly procedures, and assembly instructions. The procedures involve using various tools to remove, disassemble, and replace components like gears, bearings, seals, and housings. Precautions are outlined for cleaning parts and applying lubricants and sealants during assembly.
Caterpillar Cat 316F L Excavator (Prefix ECZ) Service Repair Manual Instant D...shanruliu7360
The document provides specifications and procedures for disassembling and assembling the final drive of a 316F L excavator. It includes 27 detailed steps to disassemble the final drive into individual components like gears, shafts, bearings, seals, and housings. Precautions are outlined for cleaning parts and applying lubricants. Required tools are specified. The document will guide maintenance technicians in repairing the final drive.
Caterpillar Cat 316F L Excavator (Prefix ECZ) Service Repair Manual (ECZ00001...fuusejkddmmd3e
This document provides specifications and disassembly/removal procedures for the final drive on a 316F L excavator. It includes detailed part numbers, torque specifications, and 27 steps to fully disassemble the final drive. Tooling requirements are specified. Cautions are provided regarding cleanliness and applying specified lubricants during assembly.
Caterpillar Cat 316F L Excavator (Prefix ECZ) Service Repair Manual (ECZ00001...jdksmmdmdd
This document provides service and repair instructions for the final drive and related components of a 316F L excavator. It includes specifications, illustrations, removal and disassembly procedures, and assembly instructions. The procedures involve using various tools to remove, disassemble, and replace components like gears, bearings, seals, and housings. Precautions are outlined for cleaning parts and applying lubricants and sealants during assembly.
Caterpillar Cat 316F L Excavator (Prefix ECZ) Service Repair Manual (ECZ00001...dujkdksmdmdm
This document provides service and repair instructions for the final drive and related components of a 316F L excavator. It includes specifications, illustrations, removal and disassembly procedures, and assembly instructions. The procedures involve using various tools to remove, disassemble, and replace components like gears, bearings, seals, and housings. Precautions are outlined for cleaning parts and applying lubricants and sealants during assembly.
Caterpillar cat 140 k 2 motor grader (prefix szw) service repair manual (szw0...fusjefjskekmem
This document provides instructions for disassembling and assembling the final drive components of a 140K 2 Motor Grader. The disassembly process involves removing 24 separate components from the final drive housing. The assembly section outlines assembling the components in the reverse order and includes checking clearances with tools. Proper lubrication and heating of bearings is required during assembly.
Caterpillar cat 349 f l excavator (prefix wna) service repair manual (wna0000...fjjskekdmme
The document provides instructions for disassembling and assembling the travel motor of a 349F L and 352F excavator. It begins by describing the required tools and safety precautions. The 32-step disassembly procedure removes components like plugs, springs, pistons, and bearings. The assembly section provides specifications, required tools, and a 28-step procedure to reinstall components in reverse order. Precautions are given to lubricate parts and apply locking agents in correct locations.
Caterpillar cat 345 d l excavator (prefix kfh) service repair manual (kfh0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group on a C13 engine, including:
1. The procedure for removing the rear gear group involves removing 10 components and using 2 required tools.
2. The installation procedure involves 11 steps and uses 1 required tool, and includes instructions for properly installing and positioning bearings.
3. Separate sections provide procedures for removing and installing the flywheel and crankshaft rear seal. Precautions are mentioned regarding handling heated parts and containing fluids.
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then describes 28 steps to reassemble the final drive, including preloading the bearings, installing seals and pins, and reassembling the carrier assembly components. Cleanliness is emphasized throughout to prevent dirt from entering internal mechanisms during disassembly and assembly.
Caterpillar cat 374 d l excavator (prefix pas) service repair manual (pas0000...fjjskekdmme
This document provides instructions for disassembling and assembling the final drive of a 374D L excavator. It lists the required tools and presents 33 steps for disassembly, removing all internal components. It then outlines 37 steps for reassembly, starting with cleaning and inspecting parts, and continuing through installing bearings, seals, gears, and housing components in the reverse order of disassembly. Tolerances and special installation tools are specified to ensure proper bearing preload and sealing.
Caterpillar cat 345 d l excavator (prefix byc) service repair manual (byc0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group on a 345D L Excavator powered by a C13 engine, including:
1. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, gears, bushings, bearings, and covers.
2. Detailed installation instructions are also provided, including proper tooling, torque specifications, and ensuring correct dimensions and alignments of components.
3. Removal and installation of the flywheel and rear crankshaft seal are also described following similar procedures.
Caterpillar cat 345 d l excavator (prefix yee) service repair manual (yee0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group and crankshaft rear seal of a 345D L Excavator with a C13 engine. The removal procedure includes using various tools to remove bolts, seals, gears, bushings, and bearings. The installation procedure provides instructions on cleaning, inspecting, applying threadlock, and installing components while ensuring proper dimensions and alignments are met. Torque specifications and notes are provided throughout.
Caterpillar cat 345 d l excavator (prefix rgd) service repair manual (rgd0000...hhfjksekmm
This document provides instructions for disassembling and assembling the travel motor of a 345D L excavator. It lists 31 steps to fully disassemble the travel motor by removing components like the head, plates, seals, pins, brake piston, disks, and housing keys. Reassembly requires reversing the disassembly steps and ensuring parts are cleaned and placed back in their original locations and orientations. Special tools are listed to aid in removal and installation of components.
Caterpillar cat 319 d l excavator (prefix wbj) service repair manual (wbj0000...fjkskedmme
The document provides instructions for disassembling and assembling a final drive component of a 319D LN excavator. It includes 33 steps for disassembly, removing components like the cover, carrier assembly, ring gears, and seals. The assembly section has 13 steps, including preloading the bearings to determine the correct shim thickness, installing seals and pins, and attaching the main housing to the motor housing. Precise cleaning and use of replacement parts is emphasized throughout.
Caterpillar cat 325 d l excavator (prefix azp) service repair manual (azp0000...hfjsekekmmd
The document provides instructions for disassembling a service repair manual for excavator models 325D and 325D L. It lists required tools and a 33-step procedure that includes removing components like the final drive, cover, gears, seals, and housing pieces. Cleanliness is important during disassembly. Parts must be reinstalled in their original locations and lifting is required as component weights range from 30 to 688 pounds.
Caterpillar cat 14 m motor grader (prefix b9j) service repair manual (b9j0000...fjsekdmmeed
This document provides disassembly instructions for the rear axle, differential, and final drive of a 14M Motor Grader. It lists 50 steps to fully disassemble these components, including removing sprockets, gears, seals, bearings, and housings. Various tools are required, and safety precautions are provided. Detailed illustrations accompany each step to show how to position parts and which fasteners to remove. Component weights are listed to assist with lifting and handling.
Caterpillar cat 325 d l excavator (prefix dbh) service repair manual (dbh0000...hfjsekekmmd
The document provides instructions for disassembling a service repair manual for excavator models 325D and 325D L. It lists required tools and a multi-step process to disassemble the final drive. Key steps include removing the final drive cover, carrier assembly, ring gears, and other internal components. Cleanliness is important during disassembly to prevent dirt from entering mechanisms.
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves using various tools to remove 37 individual parts from the final drive assembly. The assembly process similarly uses tools to reinstall the parts in the reverse order, ensuring proper installation of seals and adjusting bearing preload through precise shimming.
Caterpillar cat 325 d excavator (prefix kbe) service repair manual (kbe00001 ...hfjsekekmmd
The document provides instructions for repairing the final drive of excavator models 325D and 325D L. It involves 14 steps including cleaning parts, applying lubricants, installing seals and bearings, adjusting bearing preload, and assembling components like the carrier assembly, planetary gears, and ring gear. Proper torque values and alignment of pins are emphasized throughout the process to ensure correct assembly.
Caterpillar cat 318 f l excavator (prefix fft) service repair manual (fft0000...fjkskedmme
This document provides disassembly instructions for the final drive of a 318F L excavator. It describes 41 steps to fully disassemble the final drive components. Key steps include removing the sprocket, pistons, barrel assembly, springs, and various seals and plates. Safety warnings are provided to release pressures and contain fluids safely.
Caterpillar cat 345 c excavator (prefix wde) service repair manual (wde00001 ...fjsekdmmeed
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. The disassembly procedure involves removing 28 parts in 28 steps, including removing the final drive cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure involves installing 29 parts in 29 steps in the reverse order, adjusting bearing preload using shims, and applying anti-seize compound and thread lock to ensure proper assembly. Tools such as retaining ring pliers, eyebolts, and a transmission stand are required.
Caterpillar Cat 316F L Excavator (Prefix ECZ) Service Repair Manual Instant D...kubei069369925
The document provides service repair instructions for a 316F L excavator final drive. It includes specifications, illustrations, and step-by-step procedures for removing, disassembling, and assembling the final drive. The removal procedure involves using lifting tools to detach the final drive from the frame. The disassembly procedure has 35 steps to fully take apart the internal components. Precautions are given to clean parts and apply sealants or lubricants during assembly. Required tools are listed for each procedure.
Caterpillar Cat 316F L Excavator (Prefix ECZ) Service Repair Manual Instant D...rishang96299
This document provides service and repair instructions for the final drive and related components of a 316F L excavator. It includes specifications, illustrations, removal and disassembly procedures, and assembly instructions. The procedures involve using various tools to remove, disassemble, and replace components like gears, bearings, seals, and housings. Precautions are outlined for cleaning parts and applying lubricants and sealants during assembly.
Caterpillar Cat 316F L Excavator (Prefix ECZ) Service Repair Manual Instant D...shanruliu7360
The document provides specifications and procedures for disassembling and assembling the final drive of a 316F L excavator. It includes 27 detailed steps to disassemble the final drive into individual components like gears, shafts, bearings, seals, and housings. Precautions are outlined for cleaning parts and applying lubricants. Required tools are specified. The document will guide maintenance technicians in repairing the final drive.
Caterpillar Cat 316F L Excavator (Prefix ECZ) Service Repair Manual (ECZ00001...fuusejkddmmd3e
This document provides specifications and disassembly/removal procedures for the final drive on a 316F L excavator. It includes detailed part numbers, torque specifications, and 27 steps to fully disassemble the final drive. Tooling requirements are specified. Cautions are provided regarding cleanliness and applying specified lubricants during assembly.
Caterpillar Cat 316F L Excavator (Prefix ECZ) Service Repair Manual (ECZ00001...jdksmmdmdd
This document provides service and repair instructions for the final drive and related components of a 316F L excavator. It includes specifications, illustrations, removal and disassembly procedures, and assembly instructions. The procedures involve using various tools to remove, disassemble, and replace components like gears, bearings, seals, and housings. Precautions are outlined for cleaning parts and applying lubricants and sealants during assembly.
Caterpillar Cat 316F L Excavator (Prefix ECZ) Service Repair Manual (ECZ00001...dujkdksmdmdm
This document provides service and repair instructions for the final drive and related components of a 316F L excavator. It includes specifications, illustrations, removal and disassembly procedures, and assembly instructions. The procedures involve using various tools to remove, disassemble, and replace components like gears, bearings, seals, and housings. Precautions are outlined for cleaning parts and applying lubricants and sealants during assembly.
Caterpillar cat 316 f l excavator (prefix ecz) service repair manual (ecz0000...dkdmidkkdk
This document provides specifications and disassembly/removal procedures for the final drive on a 316F L excavator. It includes detailed part numbers, torque specifications, and 27 steps to fully disassemble the final drive. Tooling requirements are specified. Cautions are provided regarding cleanliness and marking parts for reinstallation.
Caterpillar Cat 316F L Excavator (Prefix ECZ) Service Repair Manual (ECZ00001...fujkse9didkke3
This document provides service and repair instructions for the final drive and related components of a 316F L excavator. It includes specifications, illustrations, removal and disassembly procedures, and assembly instructions. The procedures involve using various tools to remove, disassemble, and replace components like gears, bearings, seals, and housings. Precautions are outlined for cleaning parts and applying lubricants and sealants during assembly.
Caterpillar Cat 316F L Excavator (Prefix ECZ) Service Repair Manual (ECZ00001...fjkdksmmdm
This document provides service and repair instructions for the final drive and related components of a 316F L excavator. It includes specifications, illustrations, removal and disassembly procedures, and assembly instructions. The procedures involve using various tools to disassemble parts such as gears, shafts, bearings, seals, and housings. Precautions are outlined for cleaning parts and applying sealants or lubricants during assembly.
Caterpillar Cat 316F L Excavator (Prefix ECZ) Service Repair Manual (ECZ00001...orrf0370383
This document provides service and repair instructions for the final drive and related components of a 316F L excavator. It includes specifications, illustrations, removal and disassembly procedures, and assembly instructions. The procedures involve using various tools to disassemble parts such as gears, shafts, bearings, seals, and housings. Precautions are outlined for cleaning parts and applying sealants or lubricants during assembly.
Caterpillar cat 316 f l excavator (prefix ecz) service repair manual (ecz0000...fjjsekkdmme
This document provides service and repair instructions for the final drive and related components of a 316F L excavator. It includes specifications, illustrations, removal and disassembly procedures, and assembly instructions. The procedures involve using various tools to remove, disassemble, and replace components like gears, bearings, seals, and housings. Precautions are outlined for cleaning parts and applying lubricants and sealants during assembly.
Caterpillar cat 316 f l excavator (prefix ecz) service repair manual (ecz0000...fjsekdmmeed
This document provides service and repair instructions for the final drive and related components of a 316F L excavator. It includes specifications, illustrations, removal and disassembly procedures, and assembly instructions. The procedures involve using various tools to remove, disassemble, and replace components like gears, bearings, seals, and housings. Precautions are outlined for cleaning parts and applying lubricants and sealants during assembly.
Caterpillar Cat 316E L Excavator (Prefix WZY) Service Repair Manual Instant D...gongfuao7509
The document provides service repair instructions for a 316E L excavator final drive and transmission. It includes specifications, illustrations, and step-by-step procedures for removing and disassembling the final drive and transmission. The procedures describe how to remove each component and require the use of various tools to lift, separate, and disassemble heavy parts weighing up to 550 kg. Reassembly requires applying sealants and lubricants to parts before reinstalling components in the reverse order of disassembly.
Caterpillar Cat 316E L Excavator (Prefix WZY) Service Repair Manual Instant D...tengtui535
The document provides service repair instructions for a 316E L excavator final drive and related components. It includes specifications, illustrations, removal and disassembly procedures, and assembly instructions. The procedures involve using various tools to remove the final drive, disassemble it into individual parts, and replace or install new parts during reassembly. Precautions are outlined such as applying anti-seize compound and thread lock to bolts during installation.
Caterpillar Cat 316E L Excavator (Prefix WZY) Service Repair Manual Instant D...yu5676962
The document provides service repair instructions for a 316E L excavator final drive and related components. It includes specifications, illustrations, removal and disassembly procedures, and assembly instructions. The procedures involve using various tools to remove the final drive, disassemble it into individual parts, and replace or install new parts during reassembly. Precautions are outlined such as applying anti-seize compound and thread lock to bolts during installation.
Caterpillar Cat 316E L Excavator (Prefix WZY) Service Repair Manual Instant D...f8usejkdmmd8i
This document provides specifications and procedures for disassembling and assembling the final drive system on a 316E L excavator. It includes specifications for torque values, lubricants to apply, and required tools. The removal procedure is a 6 step process that uses lifting tools to detach the final drive. The disassembly procedure is a 29 step process that uses various tools to systematically remove components like gears, shafts, seals and housings. Precise alignment marks and cleanliness are emphasized throughout.
Caterpillar Cat 316E L Excavator (Prefix WZY) Service Repair Manual Instant D...ze6074xunong
This document provides specifications and procedures for disassembling and assembling the final drive system on a 316E L excavator. It includes specifications for torque values, lubricants to apply, and required tools. The removal procedure is a 6 step process that uses lifting tools to detach the final drive. The disassembly procedure is a 29 step process that uses various tools to systematically remove components like gears, shafts, seals and housings. Precise alignment marks and cleanliness are emphasized throughout.
Caterpillar Cat 316E L Excavator (Prefix WZY) Service Repair Manual Instant D...f8seodkdmdmed3
The document provides service repair instructions for a 316E L excavator final drive and transmission. It includes specifications, illustrations, and step-by-step procedures for removing and disassembling the final drive and transmission. The procedures describe how to remove each component and require the use of various tools to lift, separate, and disassemble heavy parts weighing up to 550 kg. Reassembly follows the reverse order of disassembly.
Caterpillar cat 316 e l excavator (prefix wzy) service repair manual (wzy0000...f9oseikkdks
This document provides specifications and procedures for disassembling and assembling the final drive system on a 316E L excavator. It includes specifications for torque values, lubricants to apply, and required tools. The removal procedure is a 6 step process that uses lifting tools to detach the final drive. The disassembly procedure is a 29 step process that uses various tools to systematically remove components like gears, shafts, seals and housings. Cleanliness is emphasized during disassembly.
Caterpillar Cat 316E L Excavator (Prefix WZY) Service Repair Manual (WZY00001...f8usiejdkmdd
This document provides specifications and procedures for disassembling and assembling the final drive system on a 316E L excavator. It includes specifications for torque values, lubricants to apply, and required tools. The removal procedure is a 6 step process that uses lifting tools to detach the final drive. The disassembly procedure is a 29 step process that uses various tools to systematically remove components like gears, shafts, seals and housings. Cleanliness is emphasized during disassembly.
Similar to Caterpillar cat 316 f l excavator (prefix ydl) service repair manual (ydl00001 and up) (20)
Caterpillar cat 345 c l excavator (prefix wde) service repair manual (wde0000...fjsekdmmeed
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. The disassembly procedure involves removing 28 parts in 28 steps, including removing the final drive cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure involves installing 29 parts in 29 steps in the reverse order, adjusting bearing preload using shims, and applying anti-seize compound and thread lock to ensure proper assembly. Tools such as retaining ring pliers, eyebolts, and a transmission stand are required.
Caterpillar cat 345 c l excavator (prefix spc) service repair manual (spc0000...fjsekdmmeed
The document provides instructions for disassembling and assembling a travel motor. It begins with disassembly steps including removing the head, pins, plates, seals, brake piston, separator plates, disks, and rotating group. It then details removing components from the rotating group like the shaft assembly, bearings, and piston assemblies. The assembly section provides steps to reinstall these components in reverse order and includes precautions like cleaning, applying lubricant, and ensuring proper orientation of parts.
Caterpillar cat 345 c l excavator (prefix scn) service repair manual (scn0000...fjsekdmmeed
This document provides instructions for disassembling and assembling the final drive of a 345C L excavator. The disassembly process involves removing over 20 individual parts from the final drive including the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly section outlines installing new seals, pressing in bearing cups, adjusting shims to set proper bearing preload, and reinstalling all parts in reverse order. Precise positioning of stamped identification marks on gears is required for correct reassembly.
Caterpillar cat 345 c l excavator (prefix s5m) service repair manual (s5m0000...fjsekdmmeed
This document provides instructions for disassembling and assembling the final drive of a 345C L excavator. The disassembly procedure involves removing over 20 components of the final drive including the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure instructs to clean all parts, apply anti-seize compound, install bearing cups and cones, and adjust the bearing preload using shims to achieve the proper load. Precise positioning of identification marks is required to reinstall parts in their original locations.
Caterpillar cat 345 c hydraulic excavator (prefix tdg) service repair manual ...fjsekdmmeed
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, seals, pistons, and housing pieces. It then lists 13 steps for assembly, replacing components in reverse order and noting to clean all parts, apply lubricant, and measure clearances during assembly to ensure proper operation. Tools required are listed for both disassembly and assembly.
Caterpillar cat 345 c excavator (prefix spc) service repair manual (spc00001 ...fjsekdmmeed
The document provides instructions for disassembling and assembling a travel motor. It begins with disassembly steps including removing the head, pins, plates, seals, brake piston, separator plates, disks, and rotating group components. Assembly steps are then listed in reverse order and include installing seals, spacers, piston assemblies, springs and other components back into the travel motor housing. Precautions are given such as cleaning parts and applying lubricant before assembly.
Caterpillar cat 345 c excavator (prefix dhp) service repair manual (dhp00001 ...fjsekdmmeed
The document provides instructions for disassembling and assembling a travel motor. It begins with removing external components like the displacement change valve and head. Internal components like the brake piston, disks, and rotating group are then removed. Individual parts in the rotating group like the piston assemblies and barrel are also taken apart. Precise identification and reinstallation of parts is emphasized. The assembly section provides instructions for reinstalling components in reverse order and ensuring proper placement and torque of parts.
Caterpillar cat 345 b series ii excavator (prefix dcw) service repair manual ...fjsekdmmeed
This document provides instructions for removing and installing the cylinder head on a 345B Series II Excavator with a 3176 engine. The removal procedure involves disconnecting sensors, tubes, wiring harnesses, and fuel filters before removing bolts and lifting off the cylinder head. The installation procedure specifies cleaning surfaces, installing new gaskets and seals, tightening bolts in a specific sequence, and reconnecting all components in reverse order. Tools required include wrenches, taps, and a strap wrench.
Caterpillar cat 345 b series ii excavator (prefix ccc) service repair manual ...fjsekdmmeed
This document provides instructions for removing and installing the cylinder head on a 345B Series II Excavator with a 3176C engine. The removal process involves disconnecting various sensors and tubes, removing bolts, and lifting the cylinder head off. The installation involves cleaning surfaces, installing new gaskets and seals, lifting the cylinder head into place, and torquing the head bolts to the specified sequence and values. Proper cleaning, lubrication, and torque procedures are emphasized to ensure correct installation.
Caterpillar cat 345 b series ii excavator (prefix ald) service repair manual ...fjsekdmmeed
This document provides instructions for removing and installing a lifter group on a 3176C engine. The removal process involves taking out bolts and separating the lifter assembly into sections to remove individual components like brackets, lifters and injector lifters. The installation is the reverse of removal, requiring cleaning of parts and reinstallation in the proper order and orientation. Precautions are provided to contain fluids and dispose of them according to regulations.
Caterpillar cat 345 b l excavator (prefix 9cw) service repair manual (9cw0000...fjsekdmmeed
This document provides instructions for removing and installing a cylinder head on a Caterpillar 345B L excavator engine. It details removing components like the valve mechanism cover, rocker shaft, and pushrods. It then explains how to remove the cylinder head by disconnecting sensors and tubes, and removing bolts. Reinstallation involves cleaning surfaces, installing new gaskets and seals, tightening bolts in a specific sequence, and reconnecting all removed components and hoses. Tools required are also listed.
Caterpillar cat 345 b l excavator (prefix 8rw) service repair manual (8rw0000...fjsekdmmeed
The document provides instructions for removing and installing a cylinder head and lifter group on a Caterpillar 345B L EXCAVATOR engine. It describes disconnecting various engine components and sensors, removing bolts and gaskets, and lifting the cylinder head off the engine block. It then details cleaning surfaces, installing new gaskets and seals, bolting the head back onto the block, and reconnecting all components in reverse order. Proper torque specifications are provided for all fasteners.
Caterpillar cat 345 b excavator (prefix ayr) service repair manual (ayr00001 ...fjsekdmmeed
This document provides instructions for disassembling and assembling the final drive of an excavator model 345B. It describes removing components such as the travel motor, final drive, ring gear, and carrier assemblies. Detailed steps are provided to disassemble each assembly into individual parts. The assembly section instructs cleaning and inspecting parts, applying anti-seize compound, and installing components in reverse order using lifting tools and following markings made during disassembly. Proper bearing preload is set by measuring clearance with shims.
Caterpillar cat 345 b excavator (prefix amn) service repair manual (amn00001 ...fjsekdmmeed
The document provides instructions for disassembling and assembling the travel motor of an excavator model 345B. It lists 31 steps to disassemble parts like the head, plates, seals, pistons, and housing. It then lists 27 steps to reassemble these parts in reverse order, making sure to clean parts and apply lubricant. Proper installation of seals, washers, and keys is emphasized.
Caterpillar cat 345 b excavator (prefix amj) service repair manual (amj00001 ...fjsekdmmeed
This document provides assembly instructions for installing a travel motor on a 345B Excavator. It outlines 33 steps to assemble parts like seals, pistons, plates, and shafts inside the travel motor housing. It then describes 4 steps to install the assembled travel motor onto the final drive, including cleaning surfaces, replacing an O-ring seal, and using lifting tools to maneuver the motor into position. Proper torque specifications are given for tightening fasteners.
Caterpillar cat 345 b excavator (prefix amd) service repair manual (amd00001 ...fjsekdmmeed
This document provides assembly instructions for a travel motor on a 345B Excavator. It outlines 33 steps to assemble internal components like pistons, seals, plates and housing pieces. Measurement checks are included to ensure correct assembly. The instructions also cover installing the assembled travel motor by cleaning mating surfaces, replacing an O-ring seal, and using lifting tools to slide the motor into position in the final drive housing.
Caterpillar cat 345 b excavator (prefix 8kw) service repair manual (8kw00001 ...fjsekdmmeed
This document provides instructions for removing and installing a cylinder head on a 345B excavator engine. It includes 14 steps to remove the head, such as removing sensors, tubes, and bolts. The 20 step installation procedure describes cleaning surfaces, installing gaskets and seals, tightening bolts in a specific sequence, and reconnecting related components like sensors and tubes. Special tools are listed for tasks like removing the fuel filter. Cautions are provided about containing fluids and keeping parts clean to prevent damage and wear.
Caterpillar cat 345 b excavator (prefix 6mw) service repair manual (6mw00001 ...fjsekdmmeed
The document provides instructions for disassembling and assembling the travel motor of an excavator model 345B. It lists the required tools and parts. The disassembly instructions include removing components like the brake cover, brake assembly, springs, gears, and barrel assembly. The assembly instructions list installing components like bushings, bearings, seals and rings in reverse order of disassembly. Safety notices are provided to keep parts clean and prevent hydraulic system contamination.
Caterpillar cat 340 f excavator (prefix sgh) service repair manual (sgh00001 ...fjsekdmmeed
This document provides instructions for disassembling and assembling the swing drive of a 340F Excavator. The disassembly procedure involves removing 27 parts from the swing drive including the cover, sun gear, carrier assembly, planetary gears, ring gear, and pinion shaft. The assembly procedure instructs installing lip seals and bearings on the cage and pinion shaft and pressing the cage into the swing drive housing.
Caterpillar cat 340 f excavator (prefix rbd) service repair manual (rbd00001 ...fjsekdmmeed
This document provides instructions for removing and installing the fuel manifold (rail) on a C9.3 engine. The removal procedure involves disconnecting harness assemblies, tube assemblies, and removing bolts to access the fuel manifold. Sensors, solenoid valves, and other components are then removed from the manifold. Installation is the reverse of removal, with all components torqued to the specified values. Safety notices warn of hazards from high pressure fuel and ensure cleanliness to prevent contamination of fuel system components.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 316F L EXCAVATOR YDL
Configuration: 316F L Excavator YDL00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
316F, 318F Excavator Machine Systems
Media Number -UENR5585-06 Publication Date -01/08/2015 Date Updated -12/09/2018
i07186488
Final Drive
SMCS - 4050
Specifications
Note: Callouts in the Specifications section do not match the callouts in the Remove and Install
sections.
1/34
316F L Excavator YDL00001-UP (MACHINE) POWERED BY C4.4 Engine(M00659...
2020/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g02737737
Top view
Table 1
Specification for 333-3002 Final Drive and Mounting Gp
Item Qty Part Specification Description
1 - -
Before assembly, the surfaces must be clean and free of any protective
coating.
2 40
461-3873
Bolt
Apply Loctite C5A Copper Anti-Seize to threads. Torque to
90 ± 15 N·m (66 ± 11 lb ft). Turn an additional angle of 60 ± 5 degrees.
Illustration 2 g02737820
2/34
316F L Excavator YDL00001-UP (MACHINE) POWERED BY C4.4 Engine(M00659...
2020/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Table 2
Specification for 350-0452 Final Drive Gp
Item Qty Part Specification Description
1 16
8T-7929
Bolt
Apply red Loctite 271 to the threads.
Torque to 105 ± 20 N·m (929 ± 177 lb in).
2 4
114-1539
Dowel Pin
Apply Loctite C5A Copper Anti-Seize to the inside diameter and
outside diameter of the mating parts.
3 2
296-6220
Ball Bearing
Apply Loctite C5A Copper Anti-Seize to the inside diameter and
outside diameter of the mating parts.
4 1
174-4874
Duo-Cone
Seal Gp
Rubber toric seals and all surfaces that in contact with the seals
must be clean and dry at assembly. Prior to assembly apply, a thin
layer of 6V-4876 Lubricant to the surfaces that are in contact with
the metal seals. The metal seal must be assembled square with the
bore. The rubber toric seals must not bulge. The rubber toric seals
must not be twisted.
5 6
095-0891
Spring Pin
After installation of the spring pins (5), create two stake marks for
each pin slightly near the hole of spring pins. Refer to Illustration 2
for the locations of the stake marks.
6 2
3E-2338 Pipe
Plug
Torque to 80 ± 10 N·m (59 ± 7 lb ft).
7 1
165-5790
Cover
Before assembly, apply 8C-8422 Sealant to the mating surfaces of
the cover.
8 1
165-3892
Ring Gear
Before assembly, apply 8C-8422 Sealant to the mating surfaces of
the ring gear.
9 16
227-6034
Bolt
Torque to 270 ± 40 N·m (199 ± 30 lb ft).
10 As required, use the following shims to achieve the correct clearance between the ball
bearing and the coupling gear. If two shims (10) are required, install the thinnest shim next
to the coupling gear:
1
096-1773
Shim
Thickness is 0.15 mm (0.006 inch).
1
096-1774
Shim
Thickness is 0.30 mm (0.012 inch).
1
096-1775
Shim
Thickness is 0.40 mm (0.016 inch).
1
096-1776
Shim
Thickness is 0.50 mm (0.020 inch).
1
096-1777
Shim
Thickness is 0.60 mm (0.024 inch).
1
096-1778
Shim
Thickness is 0.70 mm (0.028 inch).
3/34
316F L Excavator YDL00001-UP (MACHINE) POWERED BY C4.4 Engine(M00659...
2020/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 1 096-1779
Shim
Thickness is 0.80 mm (0.031 inch).
1
096-1780
Shim
Thickness is 1.00 mm (0.039 inch).
1
096-1781
Shim
Thickness is 1.60 mm (0.063 inch).
D - -
The distance from the edge of the spring pin hole to the stake mark
is 1.5 mm (0.06 inch).
11 1
354-4318
Nameplate
Apply Loctite 330 or activator 738 to the surface of the nameplate.
Removal Procedure
Table 3
Required Tools
Tool Part Number Part Description Qty
A
8S-7640 Stand 2
8S-7611 Tube 2
8S-7615 Pin 2
B 439-3939 Link Bracket As 2
C 154-6184 Forcing Bolt (M 20) 2
Start By:
a. Separate the track assembly. Refer to Disassembly and Assembly, "Track - Separate".
b. Remove the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Remove".
Illustration 3 g00489826
Note: Adjust the height of Tooling (A) so that there is sufficient clearance between the
sprocket and the track for the removal of the final drive.
4/34
316F L Excavator YDL00001-UP (MACHINE) POWERED BY C4.4 Engine(M00659...
2020/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 1. Lift the side of the machine to install Tooling (A) under the frame, as shown.
Illustration 4 g00712767
2. Fasten Tooling (B) and a suitable lifting device to final drive (1), as shown. Put a slight lifting
tension on the final drive.
Illustration 5 g00712737
Note: Mark the orientation of bolt holes (2) for the travel motor for installation purposes.
3. Remove bolts (3) and the washers from the final drive.
Illustration 6 g00712749
4. Use Tooling (C) to remove the final drive from the frame.
5/34
316F L Excavator YDL00001-UP (MACHINE) POWERED BY C4.4 Engine(M00659...
2020/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 5. Carefully remove final drive (1). The weight of final drive (1) and the sprocket is
approximately 312 kg (688 lb).
6. Remove Tooling (C) from the frame.
Disassembly Procedure
Table 4
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 439-3938 Link Bracket 2
C 1P-1863 Retaining Ring Pliers 1
D 439-3940 Bracket As 3
E 4C-8359 Eyebolt 2
F 439-3939 Link Bracket As 2
G 439-3941 Link Bracket As 2
Start By:
a. Remove the final drive.
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will prevent dirt from entering the internal
mechanism.
1. Put an alignment mark across the sections of the final drive for assembly purposes. The parts
must be reinstalled to the original locations.
Illustration 7 g00892878
2. Use Tooling (G) and a suitable lifting device to position the final drive assembly onto Tooling
(A). The weight of the final drive assembly is approximately 550 kg (1200 lb).
3. Remove bolts (1).
6/34
316F L Excavator YDL00001-UP (MACHINE) POWERED BY C4.4 Engine(M00659...
2020/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 8 g00892883
4. Use Tooling (B) and a suitable lifting device to remove cover (2). The weight of cover (2) is
approximately 32 kg (70 lb).
Illustration 9 g00892888
5. Remove bolts (3) and gear (4). Check plate (6). Replace plate (6) if plate (6) is worn. Remove
plugs (5) from cover (2).
Illustration 10 g00892906
6. Remove O-ring seals (7) from plugs (5).
7/34
316F L Excavator YDL00001-UP (MACHINE) POWERED BY C4.4 Engine(M00659...
2020/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 11 g00892930
7. Remove gear (8) and spacer (9).
Illustration 12 g00892965
8. Use Tooling (C) to remove retaining ring (10). Remove washer (11) and gear (12). Remove
bearing assembly (13) and washer (14).
9. Repeat Step 8 for the other two gear assemblies.
Illustration 13 g00892968
10. Remove retaining ring (15).
8/34
316F L Excavator YDL00001-UP (MACHINE) POWERED BY C4.4 Engine(M00659...
2020/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 14 g00892975
11. Remove carrier assembly (16).
Illustration 15 g02408860
12. Use a suitable press to remove the shafts from carrier assembly (16).
Illustration 16 g00892977
13. Remove gear (17) and spacer (18).
9/34
316F L Excavator YDL00001-UP (MACHINE) POWERED BY C4.4 Engine(M00659...
2020/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 17 g00892997
14. Use Tooling (D) and a suitable lifting device to remove planetary carrier (19). The weight of
planetary carrier (19) is approximately 48 kg (105 lb).
Illustration 18 g00893019
15. Remove retaining ring (21). Lift planetary carrier (19) off sun gear (20).
Illustration 19 g00896860
16. Drive spring pin (23) into planetary shaft (22).
10/34
316F L Excavator YDL00001-UP (MACHINE) POWERED BY C4.4 Engine(M006...
2020/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 20 g00893043
17. Remove planetary shaft (22). Use a suitable punch to remove spring pin (23) from planetary
shaft (22).
Illustration 21 g00896863
18. Remove washers (24) and bearing (25) from planetary gear (26).
19. Repeat Steps 16 through 18 for the other two planetary gears.
Illustration 22 g01842853
20. Remove gear (27). Remove spacer (27A).
11/34
316F L Excavator YDL00001-UP (MACHINE) POWERED BY C4.4 Engine(M006...
2020/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 23 g01842974
21. Use two people to remove carrier assembly (28). The weight of carrier assembly (28) is
approximately 38 kg (85 lb).
Illustration 24 g01843140
22. Drive spring pin (30) into shaft (29).
Illustration 25 g00893658
23. Remove shaft (29). Use a suitable punch to remove spring pin (30) from shaft (29).
12/34
316F L Excavator YDL00001-UP (MACHINE) POWERED BY C4.4 Engine(M006...
2020/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 26 g00893674
24. Remove washers (31) and bearings (32) from planetary gear (33).
25. Repeat Steps 22 through 24 for the other three planetary gears.
Illustration 27 g01208300
26. Fasten Tooling (E) and a suitable lifting device to ring gear (34), as shown. Remove ring gear
(34) from sprocket housing (35). The weight of ring gear (34) is approximately 66 kg (146 lb).
Illustration 28 g01208542
27. Remove O-ring seal (36) from sprocket housing (35).
13/34
316F L Excavator YDL00001-UP (MACHINE) POWERED BY C4.4 Engine(M006...
2020/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 29 g01208553
28. Remove bolts (37) from coupling gear (38).
Illustration 30 g01208572
29. Install suitable forcing bolts (39) in coupling gear (38). Tighten the forcing bolts evenly to
loosen coupling gear (38). Remove the coupling gear from the motor housing.
Illustration 31 g01208578
14/34
316F L Excavator YDL00001-UP (MACHINE) POWERED BY C4.4 Engine(M006...
2020/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 32 g01208625
30. Remove shims (40) from the motor housing.
Note: Inner cones and outer bearing cones (42) are a slip fit on the motor housing. While you
remove sprocket housing (35) from the motor housing, inner bearing cone (42) may stay with
the sprocket housing or the inner bearing cone may stay on the motor housing.
31. Fasten Tooling (F) and a suitable lifting device to sprocket housing (35). Separate the sprocket
housing from the motor housing. The weight of sprocket housing (35) is approximately 109 kg
(240 lb).
Illustration 33 g01208626
32. Remove the locating pins from the motor housing.
33. Remove Duo-Cone seal (41) from the motor housing.
34. If inner bearing cone (42) remained on the motor housing, then remove the inner bearing cone.
15/34
316F L Excavator YDL00001-UP (MACHINE) POWERED BY C4.4 Engine(M006...
2020/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 34 g01208633
35. Remove Duo-Cone seal (43) from the sprocket housing.
36. If inner bearing cone (42) remained on the sprocket housing, then remove the inner bearing
cone.
37. Remove the bearing cups from the sprocket housing.
Assembly Procedure
Table 5
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Stand Group 1
B 439-3938 Link Bracket 2
C 1P-1863 Retaining Ring Pliers 1
D 439-3940 Bracket As 3
E 4C-8359 Eyebolt 2
F 439-3939 Link Bracket As 2
G
8T-9206 Duo-Cone Seal Installer As 1
169-0503 Installation Kit 1
H 4C-5599 Anti-Seize Compound -
J 9S-3263 Thread Lock Compound -
K 8C-8422 Sealant -
L FT-2770 Leak down Test Tool 1
M 439-3941 Link Bracket As 2
1. Make sure that all parts of the final drive are thoroughly clean and free of dirt and debris prior
to assembly. Check the condition of all O-ring seals that are used in the final drive. If any of
16/34
316F L Excavator YDL00001-UP (MACHINE) POWERED BY C4.4 Engine(M006...
2020/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. the seals are damaged, use new parts for replacement. Reassemble the final drive on Tooling
(A).
Illustration 35 g01208879
2. Apply Tooling (H) to the surfaces inside sprocket housing (35) which comes in contact with
the bearing cups. Install a bearing cup that is in each side of the sprocket housing with a press.
Make sure that the bearing cups are properly seated.
3. Apply Tooling (H) to the surfaces inside the motor housing that comes in contact with bearing
cones (42).
4. Install inner bearing cone (42) on the motor housing.
Illustration 36 g01208625
5. Attach Tooling (F) and a suitable lifting device to sprocket housing (35). The weight of
sprocket housing (35) is approximately 109 kg (240 lb). Install sprocket housing (35) on the
motor housing. Carefully install outer bearing cone (42) on the sprocket housing.
17/34
316F L Excavator YDL00001-UP (MACHINE) POWERED BY C4.4 Engine(M006...
2020/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 37 g01208578
6. Adjust the bearing preload of the final drive. Determine the correct number of shims (40) that
are required for the proper bearing preload, as follows:
Illustration 38 g01208987
a. Use a depth micrometer to measure the step height of coupling gear (38) at several
locations around the gear. Find the average for the measured dimensions around the gear
and record the dimension. Call this Dimension (X).
b. Apply a load of 4000 kg (8820 lb) to bearing cones (42).
c. Rotate sprocket housing (35) several times to seat the bearing cones.
d. Reduce the load to 3000 ± 300 kg (6615 ± 660 lb).
18/34
316F L Excavator YDL00001-UP (MACHINE) POWERED BY C4.4 Engine(M006...
2020/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 39 g00631001
e. While the load is still on the bearing cones, measure the distance between the top face of
the motor housing and the top face of bearing cone (42). Take measurements in several
locations around the motor housing. Find the average of the measured dimensions, and
record the dimensions. Call this Dimension (Y).
f. Determine the correct thickness of shims (40) which are used between bearing cone (42)
and coupling gear (38). Use the following equation to determine the shim pack thickness.
Shim pack thickness ... (Y) − (X) ± 0.05 mm (0.002 inch)
Note: If two shims (40) are required, install the thinnest shim next to coupling gear (38)
during final assembly.
Illustration 40 g01208625
7. Attach Tooling (F) and a suitable lifting device to sprocket housing (35). Separate sprocket
housing (35) from the motor housing.
Reference: Refer to Disassembly and Assembly, "Duo-Cone Conventional Seals - Install".
Note: The rubber seals and all surfaces that comes in contact with the seals must be clean and
dry. After installation of the seals, put clean SAE 30 oil on the contact surfaces of the metal
seals.
Illustration 41 g00631006
19/34
316F L Excavator YDL00001-UP (MACHINE) POWERED BY C4.4 Engine(M006...
2020/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 42 g01208999
8. Use Tooling (G) to install Duo-Cone seal (43) in the sprocket housing.
Illustration 43 g00631014
Illustration 44 g01208626
9. Use Tooling (G) to install Duo-Cone seal (41) in the motor housing.
10. Apply Tooling (H) in the bores for the locating pins that are in the motor housing. Reinstall the
locating pins in the motor housing.
20/34
316F L Excavator YDL00001-UP (MACHINE) POWERED BY C4.4 Engine(M006...
2020/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 45 g01208625
11. Make sure that inner bearing cone (42) is seated properly on the motor housing.
Note: Do not scratch Duo-Cone seal (41) or damage the Duo-Cone seal in the main housing, or
the motor housing during assembly of the two components. After installation of the main
housing on the motor housing, there will be a small gap between the components. The gap
between the components is caused by the Duo-Cone seal. The gap will be eliminated during the
installation of coupling gear (40).
12. Fasten Tooling (F) and a suitable lifting device to sprocket housing (35). Carefully install the
sprocket housing on the motor housing.
13. Install outer bearing cone (42) on the sprocket housing. Make sure that the outer bearing cone
is properly seated.
Illustration 46 g01208578
14. Install shims (40) that were determined in Steps 6.a through 6.f on the end of the sprocket
housing. If shims were required, make sure that the thinnest shim is installed on top.
21/34
316F L Excavator YDL00001-UP (MACHINE) POWERED BY C4.4 Engine(M006...
2020/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 47 g01208553
15. Put coupling gear (38) in the original position on the motor housing.
16. Apply Tooling (J) on the threads of bolts (37) that hold coupling gear (38) in position. Tighten
bolts (37) evenly and tighten the bolts in diagonally opposite pairs.
Illustration 48 g01208542
17. Install O-ring seal (36) in sprocket housing (35).
Illustration 49 g01208300
18. Thoroughly clean the mating surface of sprocket housing (35) and the mating surface of ring
gear (34).
22/34
316F L Excavator YDL00001-UP (MACHINE) POWERED BY C4.4 Engine(M006...
2020/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. 19. Apply a bead of Tooling (K) on the mating surface of ring gear (34).
20. Attach Tooling (E) and a suitable lifting device to ring gear (34). Put ring gear (34) in position
on the sprocket housing. The weight of ring gear (34) is approximately 66 kg (146 lb). Make
sure that the alignment mark on the sprocket housing and the ring gear line up with each other.
Illustration 50 g01843479
Illustration 51 g00893674
21. Assemble carrier assembly (28), as follows.
a. Install bearings (32) in planetary gear (33).
b. Install thrust washers (31) and planetary gear (33) in the carrier assembly.
c. Use a deburring tool to remove the metal burr from the openings in the carrier. Install
planetary shaft (29) in the carrier assembly.
d. Drive spring pin (30) into planetary shaft (29).
23/34
316F L Excavator YDL00001-UP (MACHINE) POWERED BY C4.4 Engine(M006...
2020/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 52 g00941047
The stake mark is at position (S).
e. Orient the split in spring pin (30) vertically to the carrier. Align the split in the spring pin
to the top or to the bottom. Make a stake mark on each side of the spring pin hole in the
carrier. Each stake mark should be approximately 1.5 mm (0.06 inch) from the outside
diameter of the spring pin hole.
22. Repeat Steps 21.a through 21.e to install the other two planetary gears in the carrier assembly.
Illustration 53 g01842974
23. Use two people to install carrier assembly (28). The weight of carrier assembly (28) is
approximately 38 kg (85 lb).
24/34
316F L Excavator YDL00001-UP (MACHINE) POWERED BY C4.4 Engine(M006...
2020/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 54 g01842853
24. Install spacer (27A). Install gear (27).
Illustration 55 g00897548
Illustration 56 g00896863
25. Assemble planetary carrier (19), as follows.
a. Install bearing (25) in planetary gear (26).
b. Install thrust washers (24) and planetary gear (26) in the planetary carrier.
c. Use a deburring tool to remove the metal burr from the openings in the carrier. Install
planetary shaft (22) in planetary carrier (19).
25/34
316F L Excavator YDL00001-UP (MACHINE) POWERED BY C4.4 Engine(M006...
2020/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...