The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It lists 28 steps for disassembly, which include removing bolts, valves, seals, bearings, pistons, and other components. It then lists 25 steps for reassembly in reverse order, noting to clean parts thoroughly, replace all seals and gaskets, and apply a light film of oil before assembling components. Precautions are provided for parts under spring force.
The document provides step-by-step instructions for disassembling and assembling the travel motor on 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, replace seals, and apply lubricant. Precautions are given to identify parts, contain fluids, and be aware of spring forces during disassembly and assembly.
The document provides step-by-step instructions for disassembling and assembling the travel motor of 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, replace seals, and apply lubricant. Precautions are given to identify parts, contain fluids, and be aware of spring forces during disassembly and assembly.
Caterpillar Cat 315C L Excavator (Prefix CJC) Service Repair Manual (CJC00001...fuusejkddmmd3e
The document provides step-by-step instructions for disassembling and assembling the travel motor of 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. It then lists 27 steps for reassembly in reverse order, noting to clean parts, replace seals, apply lubricant and heat components as needed. Precautions are provided to prevent injury from spring forces and properly identify parts during disassembly and reassembly.
The document provides step-by-step instructions for disassembling and assembling the travel motor on 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, replace seals, and apply lubricant. Precautions are given to identify parts, contain fluids, and be aware of spring forces during disassembly and assembly.
Caterpillar Cat 315C L Excavator (Prefix CJC) Service Repair Manual (CJC00001...jdksmmdmdd
The document provides step-by-step instructions for disassembling and assembling the travel motor of 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, replace seals, and apply lubricant. Precautions are given to identify parts, contain fluids, and be aware of spring forces during disassembly and assembly.
Caterpillar Cat 315C L Excavator (Prefix CJC) Service Repair Manual (CJC00001...orrf0370383
The document provides step-by-step instructions for disassembling and assembling the travel motor on 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, replace seals, and apply lubricant. Precautions are given to identify parts, contain fluids, and be aware of spring forces during disassembly and assembly.
Caterpillar Cat 315C L Excavator (Prefix CJC) Service Repair Manual (CJC00001...fujkse9didkke3
This document provides instructions for disassembling and assembling the travel motor on 315C and 315C L Excavator models. The disassembly process involves 28 steps to remove components like bolts, valves, seals, pistons, springs, and bearings. The assembly process reverses the disassembly with 27 steps, applying grease and torque specifications, and includes heating and pressing components during installation. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar Cat 315C L Excavator (Prefix CJC) Service Repair Manual (CJC00001...dujkdksmdmdm
The document provides step-by-step instructions for disassembling and assembling the travel motor of 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, replace seals, and apply lubricant. Precautions are given to identify parts, contain fluids, and be aware of spring forces during disassembly and assembly.
The document provides step-by-step instructions for disassembling and assembling the travel motor on 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, replace seals, and apply lubricant. Precautions are given to identify parts, contain fluids, and be aware of spring forces during disassembly and assembly.
The document provides step-by-step instructions for disassembling and assembling the travel motor of 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, replace seals, and apply lubricant. Precautions are given to identify parts, contain fluids, and be aware of spring forces during disassembly and assembly.
Caterpillar Cat 315C L Excavator (Prefix CJC) Service Repair Manual (CJC00001...fuusejkddmmd3e
The document provides step-by-step instructions for disassembling and assembling the travel motor of 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. It then lists 27 steps for reassembly in reverse order, noting to clean parts, replace seals, apply lubricant and heat components as needed. Precautions are provided to prevent injury from spring forces and properly identify parts during disassembly and reassembly.
The document provides step-by-step instructions for disassembling and assembling the travel motor on 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, replace seals, and apply lubricant. Precautions are given to identify parts, contain fluids, and be aware of spring forces during disassembly and assembly.
Caterpillar Cat 315C L Excavator (Prefix CJC) Service Repair Manual (CJC00001...jdksmmdmdd
The document provides step-by-step instructions for disassembling and assembling the travel motor of 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, replace seals, and apply lubricant. Precautions are given to identify parts, contain fluids, and be aware of spring forces during disassembly and assembly.
Caterpillar Cat 315C L Excavator (Prefix CJC) Service Repair Manual (CJC00001...orrf0370383
The document provides step-by-step instructions for disassembling and assembling the travel motor on 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, replace seals, and apply lubricant. Precautions are given to identify parts, contain fluids, and be aware of spring forces during disassembly and assembly.
Caterpillar Cat 315C L Excavator (Prefix CJC) Service Repair Manual (CJC00001...fujkse9didkke3
This document provides instructions for disassembling and assembling the travel motor on 315C and 315C L Excavator models. The disassembly process involves 28 steps to remove components like bolts, valves, seals, pistons, springs, and bearings. The assembly process reverses the disassembly with 27 steps, applying grease and torque specifications, and includes heating and pressing components during installation. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar Cat 315C L Excavator (Prefix CJC) Service Repair Manual (CJC00001...dujkdksmdmdm
The document provides step-by-step instructions for disassembling and assembling the travel motor of 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, replace seals, and apply lubricant. Precautions are given to identify parts, contain fluids, and be aware of spring forces during disassembly and assembly.
Caterpillar cat 315 c l excavator (prefix cjc) service repair manual (cjc0000...dkdmidkkdk
This document provides instructions for disassembling and assembling the travel motor on 315C and 315C L Excavator models. The disassembly process involves 28 steps to remove components like bolts, valves, seals, pistons, springs, and bearings. The assembly process reverses the disassembly with 27 steps, applying grease and torque specifications, and includes heating and pressing components during installation. Cleanliness is emphasized throughout to prevent contamination.
The document provides step-by-step instructions for disassembling and assembling the travel motor on 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, replace seals, and apply lubricant. Precautions are given to identify parts, contain fluids, and be aware of spring forces during disassembly and assembly.
Caterpillar Cat 315C L Excavator (Prefix CJC) Service Repair Manual Instant D...rishang96299
The document provides step-by-step instructions for disassembling and assembling the travel motor of 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, apply lubricants, and properly set bearing temperatures and torque specifications. Safety notices are included throughout to warn of spring forces and contain fluids.
Caterpillar Cat 315C L Excavator (Prefix CJC) Service Repair Manual Instant D...kubei069369925
The document provides step-by-step instructions for disassembling and assembling the travel motor on 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, replace seals, and apply lubricant. Precautions are given to identify parts, contain fluids, and be aware of spring forces during disassembly and assembly.
This document provides instructions for disassembling and assembling the travel motor on 315C and 315C L Excavator models. The disassembly process involves 28 steps to remove components like bolts, valves, seals, pistons, springs, and bearings. The assembly process reverses the disassembly with 27 steps, applying grease and torque specifications, and includes heating and pressing components during installation. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar cat 315 c excavator (prefix cjc) service repair manual (cjc00001 ...dkdmidkkdk
The document provides step-by-step instructions for disassembling and assembling the travel motor on 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, replace seals, and apply lubricant. Precautions are given to identify parts, contain fluids, and be aware of spring forces during disassembly and assembly.
The document provides step-by-step instructions for disassembling and assembling the travel motor on 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, replace seals, and apply lubricant. Precautions are given to identify parts, contain fluids, and be aware of spring forces during disassembly and assembly.
The document provides step-by-step instructions for disassembling and assembling the travel motor of 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, replace seals, and apply lubricants. Special tools and safety precautions are noted throughout.
Caterpillar Cat 315C L Excavator (Prefix CJC) Service Repair Manual Instant D...shanruliu7360
The document provides step-by-step instructions for disassembling and assembling the travel motor of 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, replace seals, and apply lubricant. Precautions are given to identify parts, contain fluids, and be aware of spring forces during disassembly and assembly.
JCB 2DX Backhoe Loader Service Repair Manual Instant Download.pdfrishang96299
This service manual provides instructions for servicing the backhoe loader model 2DX. It contains 15 sections covering various systems of the machine including the engine, fuel system, cooling system, brakes, steering, hydraulics, and electrical systems. The excerpt focuses on servicing instructions for the engine, including safety procedures, technical specifications, operating instructions, and steps to drain and fill oil, clean parts, check oil levels, and remove and install engine components.
This document provides instructions for removing and reassembling the final drives on an excavator model 330B. The summary is:
1. The final drive must be disassembled by removing components like the ring gear, carrier assemblies, planetary gears, and seals.
2. To reassemble, components must be cleaned and seals/bearings installed before refitting parts like the carrier assemblies, ring gear, and sprocket in their original positions.
3. Precise measurements and torque specifications must be followed to set bearing preload and install retaining rings and bolts correctly.
This document provides instructions for removing and installing a cylinder head on a 325B L excavator powered by a 3116 engine. The removal procedure involves removing several other components first, like the fuel filter base and injectors. To remove the cylinder head, lifting devices are attached and bolts holding it to the cylinder block are removed. A new cylinder head gasket is installed when reinstalling the cylinder head. Precautions are given to contain fluids and keep parts clean from contaminants.
Caterpillar Cat 325B L Excavator (Prefix 5BS) Service Repair Manual Instant D...rishang96299
This document provides instructions for removing and installing a cylinder head on a 325B L excavator powered by a 3116 engine. The removal procedure involves removing several other components first, like the fuel filter base and injectors. To remove the cylinder head, lifting devices are attached and bolts holding it to the cylinder block are removed. When installing, the mating surfaces are cleaned and a new cylinder head gasket is used. Torque values and cleaning contaminants are emphasized.
This document provides instructions for disassembling and assembling the travel motor of 324E L and 324E LN Excavator models. It lists the required tools and parts and provides step-by-step instructions and illustrations for removing and installing components like the motor head, brake piston, rotating assembly, bearings, seals and other internal parts. Precautions are included to properly handle springs and ensure correct positioning of parts during assembly.
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of a 324E LN excavator.
2. It details 27 steps to disassemble components like the head, brake piston, rotating assembly, and seals.
3. The 28 steps for assembly instruct to reinstall these components in reverse order and note proper alignment of parts, use of lubrication and tools.
Caterpillar Cat 324E L Excavator (Prefix TLF) Service Repair Manual Instant D...rishang96299
This document provides instructions for disassembling and assembling the travel motor of 324E L and 324E LN Excavator models. It lists the required tools and provides step-by-step instructions and illustrations for removing and installing each component of the travel motor. The components include the head, port plate, bearings, brake piston, seals, plates, discs, shaft, races, cam plate, piston assemblies, seals, cover, and more. Precautions are provided regarding spring force and proper placement of parts.
Caterpillar Cat 324E L Excavator (Prefix LDG) Service Repair Manual Instant D...rishang96299
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of a 324E LN excavator.
2. It details 27 steps to disassemble components like the head, brake piston, rotating assembly, and seals.
3. The 28 steps for assembly instruct to reinstall these components in reverse order and include lubricating mating surfaces.
Caterpillar Cat 324E L Excavator (Prefix KTE) Service Repair Manual Instant D...rishang96299
This document provides instructions for disassembling and assembling the travel motor on 324E and 324E L excavator models. The disassembly process includes removing 28 components from the travel motor housing including the head, brake piston, plates, springs, seals and bearings. The assembly section outlines 28 steps to reinstall these components in reverse order using various tools. Special care must be taken when working with pressurized components or parts under spring force.
Caterpillar Cat 324E L Excavator (Prefix JCZ) Service Repair Manual Instant D...rishang96299
This document provides instructions for disassembling and assembling the travel motor on 324E and 324E L excavator models. The disassembly process is described in 27 steps and involves removing components like the motor head, brake piston, rotating assembly, seals, and bearings. The assembly process reverses the disassembly steps and includes lubricating components and ensuring proper alignment of parts. Tools required include retaining ring pliers, drivers, pullers, and press equipment. Cautions are provided about spring loading and containing fluids during repair work.
This document provides instructions for disassembling and assembling the travel motor on 324E and 324E L excavator models. The disassembly process includes removing 28 components from the travel motor housing including the head, brake piston, plates, springs, seals and bearings. The assembly section outlines 28 steps to reinstall these components in reverse order using various tools. Special care must be taken when working with pressurized components or parts under spring force.
This document provides instructions for disassembling and assembling the travel motor on 324E and 324E L excavator models. The disassembly process involves removing 28 components from the travel motor including the head, brake piston, plates, springs and seals. The assembly process reverses the disassembly steps and includes lubricating components and ensuring proper alignment of parts like the cam plate keys and piston marks. Special tools are required for tasks like removing races and seals.
More Related Content
Similar to Caterpillar Cat 315C L Excavator (Prefix CFT) Service Repair Manual Instant Download.pdf
Caterpillar cat 315 c l excavator (prefix cjc) service repair manual (cjc0000...dkdmidkkdk
This document provides instructions for disassembling and assembling the travel motor on 315C and 315C L Excavator models. The disassembly process involves 28 steps to remove components like bolts, valves, seals, pistons, springs, and bearings. The assembly process reverses the disassembly with 27 steps, applying grease and torque specifications, and includes heating and pressing components during installation. Cleanliness is emphasized throughout to prevent contamination.
The document provides step-by-step instructions for disassembling and assembling the travel motor on 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, replace seals, and apply lubricant. Precautions are given to identify parts, contain fluids, and be aware of spring forces during disassembly and assembly.
Caterpillar Cat 315C L Excavator (Prefix CJC) Service Repair Manual Instant D...rishang96299
The document provides step-by-step instructions for disassembling and assembling the travel motor of 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, apply lubricants, and properly set bearing temperatures and torque specifications. Safety notices are included throughout to warn of spring forces and contain fluids.
Caterpillar Cat 315C L Excavator (Prefix CJC) Service Repair Manual Instant D...kubei069369925
The document provides step-by-step instructions for disassembling and assembling the travel motor on 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, replace seals, and apply lubricant. Precautions are given to identify parts, contain fluids, and be aware of spring forces during disassembly and assembly.
This document provides instructions for disassembling and assembling the travel motor on 315C and 315C L Excavator models. The disassembly process involves 28 steps to remove components like bolts, valves, seals, pistons, springs, and bearings. The assembly process reverses the disassembly with 27 steps, applying grease and torque specifications, and includes heating and pressing components during installation. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar cat 315 c excavator (prefix cjc) service repair manual (cjc00001 ...dkdmidkkdk
The document provides step-by-step instructions for disassembling and assembling the travel motor on 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, replace seals, and apply lubricant. Precautions are given to identify parts, contain fluids, and be aware of spring forces during disassembly and assembly.
The document provides step-by-step instructions for disassembling and assembling the travel motor on 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, replace seals, and apply lubricant. Precautions are given to identify parts, contain fluids, and be aware of spring forces during disassembly and assembly.
The document provides step-by-step instructions for disassembling and assembling the travel motor of 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, replace seals, and apply lubricants. Special tools and safety precautions are noted throughout.
Caterpillar Cat 315C L Excavator (Prefix CJC) Service Repair Manual Instant D...shanruliu7360
The document provides step-by-step instructions for disassembling and assembling the travel motor of 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, replace seals, and apply lubricant. Precautions are given to identify parts, contain fluids, and be aware of spring forces during disassembly and assembly.
Similar to Caterpillar Cat 315C L Excavator (Prefix CFT) Service Repair Manual Instant Download.pdf (9)
JCB 2DX Backhoe Loader Service Repair Manual Instant Download.pdfrishang96299
This service manual provides instructions for servicing the backhoe loader model 2DX. It contains 15 sections covering various systems of the machine including the engine, fuel system, cooling system, brakes, steering, hydraulics, and electrical systems. The excerpt focuses on servicing instructions for the engine, including safety procedures, technical specifications, operating instructions, and steps to drain and fill oil, clean parts, check oil levels, and remove and install engine components.
This document provides instructions for removing and reassembling the final drives on an excavator model 330B. The summary is:
1. The final drive must be disassembled by removing components like the ring gear, carrier assemblies, planetary gears, and seals.
2. To reassemble, components must be cleaned and seals/bearings installed before refitting parts like the carrier assemblies, ring gear, and sprocket in their original positions.
3. Precise measurements and torque specifications must be followed to set bearing preload and install retaining rings and bolts correctly.
This document provides instructions for removing and installing a cylinder head on a 325B L excavator powered by a 3116 engine. The removal procedure involves removing several other components first, like the fuel filter base and injectors. To remove the cylinder head, lifting devices are attached and bolts holding it to the cylinder block are removed. A new cylinder head gasket is installed when reinstalling the cylinder head. Precautions are given to contain fluids and keep parts clean from contaminants.
Caterpillar Cat 325B L Excavator (Prefix 5BS) Service Repair Manual Instant D...rishang96299
This document provides instructions for removing and installing a cylinder head on a 325B L excavator powered by a 3116 engine. The removal procedure involves removing several other components first, like the fuel filter base and injectors. To remove the cylinder head, lifting devices are attached and bolts holding it to the cylinder block are removed. When installing, the mating surfaces are cleaned and a new cylinder head gasket is used. Torque values and cleaning contaminants are emphasized.
This document provides instructions for disassembling and assembling the travel motor of 324E L and 324E LN Excavator models. It lists the required tools and parts and provides step-by-step instructions and illustrations for removing and installing components like the motor head, brake piston, rotating assembly, bearings, seals and other internal parts. Precautions are included to properly handle springs and ensure correct positioning of parts during assembly.
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of a 324E LN excavator.
2. It details 27 steps to disassemble components like the head, brake piston, rotating assembly, and seals.
3. The 28 steps for assembly instruct to reinstall these components in reverse order and note proper alignment of parts, use of lubrication and tools.
Caterpillar Cat 324E L Excavator (Prefix TLF) Service Repair Manual Instant D...rishang96299
This document provides instructions for disassembling and assembling the travel motor of 324E L and 324E LN Excavator models. It lists the required tools and provides step-by-step instructions and illustrations for removing and installing each component of the travel motor. The components include the head, port plate, bearings, brake piston, seals, plates, discs, shaft, races, cam plate, piston assemblies, seals, cover, and more. Precautions are provided regarding spring force and proper placement of parts.
Caterpillar Cat 324E L Excavator (Prefix LDG) Service Repair Manual Instant D...rishang96299
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of a 324E LN excavator.
2. It details 27 steps to disassemble components like the head, brake piston, rotating assembly, and seals.
3. The 28 steps for assembly instruct to reinstall these components in reverse order and include lubricating mating surfaces.
Caterpillar Cat 324E L Excavator (Prefix KTE) Service Repair Manual Instant D...rishang96299
This document provides instructions for disassembling and assembling the travel motor on 324E and 324E L excavator models. The disassembly process includes removing 28 components from the travel motor housing including the head, brake piston, plates, springs, seals and bearings. The assembly section outlines 28 steps to reinstall these components in reverse order using various tools. Special care must be taken when working with pressurized components or parts under spring force.
Caterpillar Cat 324E L Excavator (Prefix JCZ) Service Repair Manual Instant D...rishang96299
This document provides instructions for disassembling and assembling the travel motor on 324E and 324E L excavator models. The disassembly process is described in 27 steps and involves removing components like the motor head, brake piston, rotating assembly, seals, and bearings. The assembly process reverses the disassembly steps and includes lubricating components and ensuring proper alignment of parts. Tools required include retaining ring pliers, drivers, pullers, and press equipment. Cautions are provided about spring loading and containing fluids during repair work.
This document provides instructions for disassembling and assembling the travel motor on 324E and 324E L excavator models. The disassembly process includes removing 28 components from the travel motor housing including the head, brake piston, plates, springs, seals and bearings. The assembly section outlines 28 steps to reinstall these components in reverse order using various tools. Special care must be taken when working with pressurized components or parts under spring force.
This document provides instructions for disassembling and assembling the travel motor on 324E and 324E L excavator models. The disassembly process involves removing 28 components from the travel motor including the head, brake piston, plates, springs and seals. The assembly process reverses the disassembly steps and includes lubricating components and ensuring proper alignment of parts like the cam plate keys and piston marks. Special tools are required for tasks like removing races and seals.
This document provides the disassembly and assembly procedures for a 324D LN excavator travel motor. It includes 28 steps for disassembly that remove components like the motor head, seals, plates, discs, bearings, and housing pieces. The 28 steps for assembly install these same components in reverse order and include notes about cleaning, applying lubricant, and ensuring proper positioning of parts. Tools required are also listed.
The document provides instructions for disassembling the final drive of an excavator. Key steps include:
1. Marking the final drive for alignment and securing it to a repair stand.
2. Removing bolts and lifting devices to extract the cover and internal gears and shafts.
3. Using retaining ring pliers and presses to separate additional components like carriers.
4. Hammering out pins to dismantle planetary gear sets from within the carriers.
This document provides the disassembly and assembly procedures for a travel motor on excavator models 324D L and 324D LN. The disassembly procedure is outlined in 28 steps and includes removing components like the head, seals, springs, plates, and bearings. The assembly procedure reverses the disassembly steps in 15 illustrated steps and provides notes on cleaning, applying thread lock compound and lubricant, and ensuring parts are returned to their original positions.
Caterpillar Cat 324D L Excavator (Prefix TRH) Service Repair Manual Instant D...rishang96299
This document provides the disassembly and assembly procedures for a 324D LN excavator travel motor. It includes 28 steps for disassembly that remove components like the motor head, seals, plates, discs, bearings, and housing pieces. The 28 steps for assembly install these same components in reverse order and include notes about cleaning, applying lubricant, and ensuring proper positioning of parts. Tools required are also listed.
Caterpillar Cat 324D L Excavator (Prefix SYM) Service Repair Manual Instant D...rishang96299
This document provides disassembly instructions for the final drive of an excavator model 324D L and 324D LN. The 31 step procedure includes removing the final drive housing, cover, gears, carriers, shafts, seals and other components. Special tools are listed that are required, and safety notes about cleanliness and part markings for reassembly are provided. Detailed illustrations accompany each step to show how to disassemble the various parts of the final drive.
Caterpillar Cat 324D L Excavator (Prefix PYT) Service Repair Manual Instant D...rishang96299
This document provides instructions for disassembling and assembling the final drive of a 324D L Excavator. The assembly procedure involves 37 steps and requires various tools. Key steps include pressing bearings into housings, measuring bearing preload, installing seals using special tools, and applying anti-seize compound to surfaces. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar Cat 324D L Excavator (Prefix JJG) Service Repair Manual Instant D...rishang96299
The document provides instructions for disassembling a final drive on an excavator. It lists required tools and a multi-step process involving removing bolts, gears, carriers, shafts, seals, and other components. Cleanliness is important to prevent dirt from entering during disassembly. Parts must be reinstalled in their original locations later. Various components like covers, gears and carriers are removed using lifting devices due to their significant weights ranging from 30-312 kg.
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
Automotive Engine Valve Manufacturing Plant Project Report.pptxSmith Anderson
The report provides a complete roadmap for setting up an Automotive Engine Valve. It covers a comprehensive market overview to micro-level information such as unit operations involved, raw material requirements, utility requirements, infrastructure requirements, machinery and technology requirements, manpower requirements, packaging requirements, transportation requirements, etc.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315C EXCAVATOR CFT
Configuration: 315C & 315C L Excavators CFT00001-UP (MACHINE) POWERED BY 3046 Engine
Disassembly and Assembly
315C Excavator Machine Systems
Media Number -RENR5525-05 Publication Date -01/11/2008 Date Updated -10/11/2008
i01959727
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
B 1P-0074 Slide Hammer 1
C 9S-9152 Bearing Puller 1
D
1U-9895 Crossblock 1
3H-0465 Push-Puller Plate 2
8T-0649 Bolt 2
9X-8257 Washer 2
E 5P-0975 Plate 1
Start By:
a. Remove the piston motor (travel). Refer to Disassembly and Assembly, "Piston Motor
(Travel) - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
1/12
315C & 315C L Excavators CFT00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
Note: Put identification marks on the motor and on all hose assemblies for installation purposes
and for the purpose of orientation. Plug all hose assemblies. This will help to prevent fluid loss
and this helps to keep contaminants from entering the system.
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
Illustration 1 g00779154
1. Remove bolts (1).
Illustration 2 g00779159
2/12
315C & 315C L Excavators CFT00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 2. Remove bolts (2) from the traction control valve in order to install Tooling (A).
Illustration 3 g00779163
3. Remove traction control valve (3) and travel motor (4) from the final drive.
Illustration 4 g00779215
4. Remove Tooling (A). Remove four bolts (2). Remove traction control valve (3).
Illustration 5 g01018464
5. Remove socket head bolts (5). Remove O-ring seal (6) and O-ring seals (7). Remove head
(8).
3/12
315C & 315C L Excavators CFT00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 6 g00779238
6. Remove shim (9).
Illustration 7 g00779248
7. Remove bearing (10).
Illustration 8 g00779259
8. Remove plugs (11) and the O-ring seals.
4/12
315C & 315C L Excavators CFT00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 9 g01018466
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
9. Remove adapter (14) and the O-ring seal. Remove spool (13) and spring (12) from head (8).
Illustration 10 g00779279
10. Remove washer set (15).
5/12
315C & 315C L Excavators CFT00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 11 g00779289
11. Remove port plate (16).
Illustration 12 g00780482
Illustration 13 g01020385
12. Remove three small O-ring seals (17). Install Tooling (D) and Tooling (E), as shown.
Tooling (E) provides a protective cover for the barrel assembly. Tooling (E) prevents
Tooling (D) from damaging the surface of the barrel assembly.
6/12
315C & 315C L Excavators CFT00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. 13. Retain piston (18) with Tooling (D) and apply approximately 517 kPa (75 psi) of shop air
pressure to brake release port (Y). Brake piston (18) will move out of the piston guide.
Remove brake piston (18) from the main housing.
Illustration 14 g00779307
14. Remove O-ring seal (19) and the backup ring and remove O-ring seal (20) and the backup
ring.
Illustration 15 g00779310
15. Remove piston guide (21). Remove O-ring seal (22).
Illustration 16 g00779341
7/12
315C & 315C L Excavators CFT00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 16. Remove O-ring seal (23) and backup ring (24).
Illustration 17 g00779343
17. Lay the travel motor housing on one side in order to remove rotating group (25) and brake
pack (26) as a unit.
Illustration 18 g00780107
18. Remove brake pack (26).
Illustration 19 g00780290
8/12
315C & 315C L Excavators CFT00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. NOTICE
In order to ensure that each piston assembly is installed into its original
bore, identify and mark each piston assembly, retaining plate and the
barrel before removing the piston assembly.
To avoid damage to the barrel assembly parts, do not allow the parts to
separate from the assembly during removal or installation.
19. Remove pistons (27) and retainer plate (28) from barrel (29) as a unit. Separate the pistons
from the retainer plate.
Illustration 20 g00780317
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
20. Remove guide (30), spacer (31), and nine springs (32) from the barrel.
9/12
315C & 315C L Excavators CFT00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 21 g00780328
21. Remove swashplate (33).
Illustration 22 g00780348
22. Use a magnet in order to remove keys (34) and pistons (35).
Illustration 23 g00780352
23. Use a magnet in order to remove pins (36).
10/12
315C & 315C L Excavators CFT00001-UP (MACHINE) POWERED BY 3046 Eng...
2020/11/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 24 g00780345
24. Remove shaft assembly (37). Remove plugs (38) and the O-ring seals.
Illustration 25 g01020388
25. Use Tooling (B) in order to remove seal (39).
Illustration 26 g00780494
26. Remove retaining rings (40) from each side of the bearing.
11/12
315C & 315C L Excavators CFT00001-UP (MACHINE) POWERED BY 3046 Eng...
2020/11/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 27 g00780502
27. Use a suitable press in order to remove bearing assembly (41) from shaft (42).
Illustration 28 g00780544
28. Use a suitable press and Tooling (C) in order to remove inner race (43) from shaft (42).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Nov 12 16:01:33 UTC+0800 2020
12/12
315C & 315C L Excavators CFT00001-UP (MACHINE) POWERED BY 3046 Eng...
2020/11/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315C EXCAVATOR CFT
Configuration: 315C & 315C L Excavators CFT00001-UP (MACHINE) POWERED BY 3046 Engine
Disassembly and Assembly
315C Excavator Machine Systems
Media Number -RENR5525-05 Publication Date -01/11/2008 Date Updated -10/11/2008
i01959745
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
F 1P-0510 Driver Group 1
G 206-3689 Turning Tool 1
H 5P-0960 Molybdenum Grease 1
Note: Replace all O-ring seals and gaskets. Apply a light film of "10W" oil to all components
before assembly.
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
1/13
315C & 315C L Excavators CFT00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 1 g00780677
1. Raise the temperature of inner race (43). Lower the temperature of shaft (42). Use a soft
hammer in order to install inner race (43) on shaft (42).
Illustration 2 g00780698
2. Raise the temperature of bearing assembly (41). Lower the temperature of shaft (42). Install
bearing assembly (41) on shaft (42).
Illustration 3 g00780494
3. Install retaining rings (40) on each side of the bearing.
2/13
315C & 315C L Excavators CFT00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 4 g01018474
4. Use Tooling (F) in order to install seal (39).
Illustration 5 g00780715
5. Use a soft hammer in order to install shaft assembly (37).
Illustration 6 g00780723
6. Install plugs (38) and the O-ring seals. Tighten plugs (38) to a torque of 140 ± 14 N·m
(103 ± 10 lb ft).
3/13
315C & 315C L Excavators CFT00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 7 g00780352
7. Use a magnet in order to install pins (36).
Illustration 8 g00780839
NOTICE
The locating pin on each key is not centered. In order to prevent
damage to the barrel assembly during assembly of the travel motor, the
keys must be installed as shown. Also, the keys must be installed in the
key's original location in the body of the travel motor.
8. Install pistons (34) and keys (35).
4/13
315C & 315C L Excavators CFT00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 9 g00780328
9. Install swashplate (33).
Illustration 10 g00780317
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
10. Install nine springs (32), spacer (31), and guide (30) into the barrel.
5/13
315C & 315C L Excavators CFT00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 11 g00780290
11. Install pistons (27) into the retainer plate (28). Install pistons (27) and retainer plate (28) as
a unit into barrel (29) .
Note: Use string in order to keep the rotating group from separating during installation.
Illustration 12 g00780870
12. Install rotating group (25).
Illustration 13 g00780887
13. Install brake pack (26).
6/13
315C & 315C L Excavators CFT00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 14 g00780817
14. Install O-ring seal (23) and backup ring (24) on piston guide (21).
Illustration 15 g00779310
15. Install piston guide (21). Install O-ring seal (22).
7/13
315C & 315C L Excavators CFT00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 16 g00779307
16. Install O-ring seal (19) and the backup ring and install O-ring seal (20) and the backup ring.
Illustration 17 g00797765
Note: Make sure that brake piston (18) is thoroughly clean and free of dirt and debris.
17. Install three small O-ring seals (17). Install piston (18).
Illustration 18 g00779289
18. Install port plate (16).
8/13
315C & 315C L Excavators CFT00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 19 g00779279
19. Install washer set (15).
Illustration 20 g01018466
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
20. Install spring (12) and spool (13) into head (8). Install adapter (14) and the O-ring seal into
head (8).
Illustration 21 g00779259
21. Install plugs (11) and the O-ring seals.
9/13
315C & 315C L Excavators CFT00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 22 g00779248
22. Lower the temperature of bearing (10) and install bearing (10).
Illustration 23 g00779238
23. Use a shim or shims (9) so that the following requirements are met.
Note: During the following checks, turn the travel motor output shaft in a clockwise
direction.
Illustration 24 g01018475
10/13
315C & 315C L Excavators CFT00001-UP (MACHINE) POWERED BY 3046 Eng...
2020/11/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. a. Use Tooling (G) in order to turn the output shaft. The travel motor output shaft does
not rotate with an applied torque of 440 N·m (325 lb ft) with the parking brake release
port open.
Illustration 25 g01018476
b. Apply the air pressure at orifice (X). Use Tooling (G) in order to turn the output shaft
when the parking brake release port is pressurized to 780 kPa (115 psi). Perform this
procedure with the inlet port and the outlet port open to the hydraulic oil tank. The
travel motor output shaft rotates with an applied torque of 29 N·m (21 lb ft) or less.
Note: It may be necessary to remove head (8) several times in order to determine the correct
thickness of shim or shims (9) that are used to adjust the rolling torque of the travel motor
output shaft.
24. Apply a thin layer of Tooling (H) on shim or shims (9). Install the shim or shims on the
head. The grease will hold the shim or shims in place during the installation of the head.
Install the head on the body of the travel motor.
Illustration 26 g01018464
NOTICE
To prevent possible damage to the travel motor, fill the unit with oil at
least to the fill port before operating the machine. Refer to the
Operation and Maintenance Manual for the correct oil specification.
11/13
315C & 315C L Excavators CFT00001-UP (MACHINE) POWERED BY 3046 Eng...
2020/11/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. 25. Install O-ring seal (6) and O-ring seals (7). Install head (8 ). Install socket head bolts (5).
Tighten bolts (5) to a torque of 177 ± 18 N·m (131 ± 13 lb ft).
Illustration 27 g00779215
26. Install Tooling (A). Install traction control valve (3). Remove Tooling (A). Install six bolts
(2). Tighten bolts (2) to a torque of 80 ± 8 N·m (59 ± 6 lb ft).
Illustration 28 g00779163
27. Install traction control valve (3) and travel motor (4) into the final drive as a unit.
12/13
315C & 315C L Excavators CFT00001-UP (MACHINE) POWERED BY 3046 Eng...
2020/11/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
27. Illustration 29 g00779154
28. Install bolts (1). Tighten bolts (1) to a torque of 240 ± 40 N·m (177 ± 30 lb ft).
End By:
a. Install the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Nov 12 16:02:29 UTC+0800 2020
13/13
315C & 315C L Excavators CFT00001-UP (MACHINE) POWERED BY 3046 Eng...
2020/11/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...