The document provides step-by-step instructions for disassembling and assembling the travel motor of 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, replace seals, and apply lubricant. Precautions are given to identify parts, contain fluids, and be aware of spring forces during disassembly and assembly.
Caterpillar cat 315 c l excavator (prefix cft) service repair manual (cft0000...fjsekdmmeed
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It describes 27 steps to disassemble the travel motor by removing components like bolts, seals, bearings, pistons, and plates. It then describes 26 steps for reassembling the motor by installing these components in the reverse order. Precautions are provided to mark parts, clean them, apply lubricants, and take care when installing spring-loaded parts.
Caterpillar cat 315 c excavator (prefix cft) service repair manual (cft00001 ...fjjsekkdmme
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It describes 27 steps to disassemble the travel motor by removing components like bolts, seals, bearings, pistons, and plates. It then describes 26 steps for reassembling the travel motor by installing these components in the reverse order. Precautions are provided to mark parts, clean them, apply lubricants, and take care when installing spring-loaded or sealed components.
Caterpillar cat 315 c excavator (prefix cft) service repair manual (cft00001 ...fjsekdmmeed
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It describes 27 steps to disassemble the motor by removing components like bolts, seals, bearings, pistons, plates and shafts. It then describes 26 steps for reassembling the motor by installing these components in the reverse order. Precautions are provided to mark parts, clean them, apply lubricants and take care when removing or installing springs and seals. Tools required for specific steps are also listed.
Caterpillar cat 315 c l excavator (prefix cft) service repair manual (cft0000...fjjsekkdmme
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It describes 27 steps to disassemble the travel motor by removing components like bolts, seals, bearings, pistons, and plates. It then describes 26 steps for reassembling the travel motor by installing these components in the reverse order. Precautions are provided to mark parts, clean them, apply lubricants, and take care when installing spring-loaded or sealed components.
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It describes 27 steps to disassemble the travel motor by removing components like bolts, seals, bearings, pistons, and plates. It then describes 26 steps for reassembling the travel motor by installing these components in the reverse order. Precautions are provided to mark parts, clean them, apply lubricants, and take care when installing spring-loaded or sealed components.
Caterpillar Cat 315C L Excavator (Prefix CFT) Service Repair Manual (CFT00001...orrf0370383
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It describes 27 steps to disassemble the travel motor by removing components like bolts, seals, bearings, pistons, and plates. It then describes 26 steps for reassembling the travel motor by installing these components in the reverse order. Precautions are provided to mark parts, clean them, apply lubricants, and take care when installing spring-loaded or sealed components.
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It lists 28 steps for disassembly, which include removing bolts, valves, seals, bearings, pistons, and other components. It then lists 25 steps for reassembly in reverse order, noting to clean parts thoroughly, replace all seals and gaskets, and apply a light film of oil before assembling components. Precautions are provided for parts under spring force.
Caterpillar Cat 315C L Excavator (Prefix CFT) Service Repair Manual Instant D...rishang96299
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It lists 28 steps for disassembly, which include removing bolts, valves, seals, bearings, pistons, and other components. It then lists 25 steps for reassembly in reverse order, noting to clean parts thoroughly, replace all seals and gaskets, and apply a light film of oil before assembling components. Precautions are provided for parts under spring force.
Caterpillar cat 315 c l excavator (prefix cft) service repair manual (cft0000...fjsekdmmeed
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It describes 27 steps to disassemble the travel motor by removing components like bolts, seals, bearings, pistons, and plates. It then describes 26 steps for reassembling the motor by installing these components in the reverse order. Precautions are provided to mark parts, clean them, apply lubricants, and take care when installing spring-loaded parts.
Caterpillar cat 315 c excavator (prefix cft) service repair manual (cft00001 ...fjjsekkdmme
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It describes 27 steps to disassemble the travel motor by removing components like bolts, seals, bearings, pistons, and plates. It then describes 26 steps for reassembling the travel motor by installing these components in the reverse order. Precautions are provided to mark parts, clean them, apply lubricants, and take care when installing spring-loaded or sealed components.
Caterpillar cat 315 c excavator (prefix cft) service repair manual (cft00001 ...fjsekdmmeed
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It describes 27 steps to disassemble the motor by removing components like bolts, seals, bearings, pistons, plates and shafts. It then describes 26 steps for reassembling the motor by installing these components in the reverse order. Precautions are provided to mark parts, clean them, apply lubricants and take care when removing or installing springs and seals. Tools required for specific steps are also listed.
Caterpillar cat 315 c l excavator (prefix cft) service repair manual (cft0000...fjjsekkdmme
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It describes 27 steps to disassemble the travel motor by removing components like bolts, seals, bearings, pistons, and plates. It then describes 26 steps for reassembling the travel motor by installing these components in the reverse order. Precautions are provided to mark parts, clean them, apply lubricants, and take care when installing spring-loaded or sealed components.
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It describes 27 steps to disassemble the travel motor by removing components like bolts, seals, bearings, pistons, and plates. It then describes 26 steps for reassembling the travel motor by installing these components in the reverse order. Precautions are provided to mark parts, clean them, apply lubricants, and take care when installing spring-loaded or sealed components.
Caterpillar Cat 315C L Excavator (Prefix CFT) Service Repair Manual (CFT00001...orrf0370383
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It describes 27 steps to disassemble the travel motor by removing components like bolts, seals, bearings, pistons, and plates. It then describes 26 steps for reassembling the travel motor by installing these components in the reverse order. Precautions are provided to mark parts, clean them, apply lubricants, and take care when installing spring-loaded or sealed components.
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It lists 28 steps for disassembly, which include removing bolts, valves, seals, bearings, pistons, and other components. It then lists 25 steps for reassembly in reverse order, noting to clean parts thoroughly, replace all seals and gaskets, and apply a light film of oil before assembling components. Precautions are provided for parts under spring force.
Caterpillar Cat 315C L Excavator (Prefix CFT) Service Repair Manual Instant D...rishang96299
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It lists 28 steps for disassembly, which include removing bolts, valves, seals, bearings, pistons, and other components. It then lists 25 steps for reassembly in reverse order, noting to clean parts thoroughly, replace all seals and gaskets, and apply a light film of oil before assembling components. Precautions are provided for parts under spring force.
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It lists 28 steps for disassembly, which include removing bolts, valves, seals, bearings, pistons, and other components. It then lists 27 steps for reassembly in reverse order, noting to clean parts thoroughly, replace all seals and gaskets, and apply a light film of oil before assembling components. Precautions are provided for parts under spring pressure.
Caterpillar Cat 315C L Excavator (Prefix CFT) Service Repair Manual Instant D...kubei069369925
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It describes 27 steps to disassemble the motor by removing components like bolts, seals, bearings, pistons, springs and plates. It then describes 26 steps for reassembling the motor by installing these components in the reverse order. Precautions are provided to mark parts, clean them, apply lubricants and take care when removing or installing parts with spring forces.
Caterpillar Cat 315C L Excavator (Prefix CFT) Service Repair Manual (CFT00001...fuusejkddmmd3e
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It lists 28 steps for disassembly, which include removing bolts, valves, seals, bearings, pistons, and other components. It then lists 27 steps for reassembly in reverse order, noting to clean parts thoroughly, replace all seals and gaskets, and apply a light film of oil before assembling components. Precautions are provided for parts under spring pressure.
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It lists 28 steps for disassembly, which include removing bolts, valves, seals, bearings, pistons, and other components. It then lists 27 steps for reassembly in reverse order, noting to clean parts thoroughly, replace all seals and gaskets, and apply a light film of oil before assembling components. Precautions are provided for parts under spring pressure.
Caterpillar cat 315 c excavator (prefix cft) service repair manual (cft00001 ...dkdmidkkdk
This document provides instructions for disassembling and assembling the travel motor on 315C and 315C L Excavator models. The disassembly process involves 27 steps to remove components like the traction control valve, travel motor, piston motor, brake pack, pistons, and bearings. The assembly process reverses the disassembly with 23 steps and cautions to clean parts, replace seals and gaskets, apply lubricant, and heat/cool components for proper installation. Proper tooling and following all steps is important to prevent damage during disassembly and assembly.
Caterpillar Cat 315C L Excavator (Prefix CFT) Service Repair Manual (CFT00001...dujkdksmdmdm
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It lists 28 steps for disassembly, which include removing bolts, valves, seals, bearings, pistons, and other components. It then lists 25 steps for reassembly in reverse order, noting to clean parts thoroughly, replace all seals and gaskets, and apply a light film of oil before assembling components. Precautions are provided for parts under spring force.
This document provides instructions for disassembling and assembling the travel motor on 315C and 315C L Excavator models. The disassembly process involves 27 steps to remove components like the traction control valve, travel motor, piston motor, brake pack, pistons, and bearings. The assembly process reverses the disassembly with 23 steps and cautions to clean parts, replace seals and gaskets, apply lubricant, and heat/cool components for proper installation. Proper tooling and following all steps is important to prevent damage during disassembly and assembly.
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It describes 27 steps to disassemble the motor by removing components like bolts, seals, bearings, pistons, springs and plates. It then describes 26 steps for reassembling the motor by installing these components in the reverse order. Precautions are provided to mark parts, clean them, apply lubricants and take care when removing or installing parts with spring forces.
The document provides instructions for removing and installing various components of an excavator engine, including the combustion head, ARD nozzle heater relay, ARD fuel solenoid valve, and exhaust manifold. The procedures include required tools, safety warnings, step-by-step instructions, and torque specifications for reinstallation.
This document provides disassembly instructions for a 336D2 excavator travel motor. It outlines 27 steps to fully disassemble the travel motor. These include removing the motor head assembly, piston assemblies, barrel assembly, springs, seals, plates, and other internal components. Tools required include bolting fixtures, pry bars, pullers, and seal removal tools. Precautions are provided to retain component positioning for reassembly and to contain hydraulic fluids.
This document provides disassembly instructions for the travel motor on a 336F L XE excavator. It lists 27 steps to fully disassemble the travel motor, including removing the head, springs, relief valves, pistons, barrel assembly, swashplate and other internal components. Detailed illustrations accompany each step to show how to properly remove parts and note their positions for reassembly. Safety precautions are provided to warn of potential spring forces and contain fluids during disassembly.
Caterpillar Cat 336F L XE Excavator (Prefix MTW) Service Repair Manual (MTW00...jdksmmdmdd
This document provides disassembly instructions for a travel motor on a 336F LN XE excavator. It lists 27 steps to fully disassemble the travel motor, including removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals, and more. Detailed illustrations accompany each step to show how to remove each part in the proper sequence. Safety precautions are provided to warn of potential spring forces and contain fluids during disassembly. Required tools are listed that will be needed to complete the process.
Caterpillar Cat 336F L XE Excavator (Prefix YBH) Service Repair Manual (YBH00...jdksmmdmdd
This document provides instructions for disassembling the travel motor on a 336F LNXE excavator. The 27 step procedure includes removing components like the motor head assembly, barrel assembly, piston assemblies, springs, seals, plates and more. Special care must be taken when removing components under spring pressure. Tools and safety precautions are listed for each step. The goal is to disassemble all parts while keeping them organized for proper reassembly.
This document provides instructions to disassemble a travel motor on a 349F and 349F L excavator. It outlines 27 steps to fully disassemble the travel motor, removing components like the motor head assembly, port plate, springs, seals, bearings, valves and more. Precautions are provided to be aware of parts under spring force. Various specialized tools are required to properly support, attach, extract and remove components from the motor.
Caterpillar Cat 349E L Excavator (Prefix FJB) Service Repair Manual (FJB00001...jdksmmdmdd
The document provides instructions for disassembling and assembling a hydraulic fan drive for an excavator. It details 22 steps for disassembly, removing components like bolts, retainers, seals, discs, and housing pieces. It then details 14 steps for reassembly, including pressing in bearings and seals, installing retaining rings, and pressing the shaft assembly back into place using the proper tools. Cleanliness is emphasized throughout to prevent contamination of precision components.
Caterpillar Cat 349E L Excavator (Prefix KFX) Service Repair Manual (KFX00001...jdksmmdmdd
The document provides instructions for disassembling and assembling a travel motor on a 349E L VG excavator. It includes 27 steps for disassembly and 18 steps for assembly. Key parts that are removed and installed include the head assembly, brake housing, rotating group, barrel assembly, pistons, bearings and seals. Tools and torque specifications are provided for correct disassembly and reassembly.
The document provides step-by-step instructions to disassemble a travel motor on an excavator model 349F L. It details 27 steps to remove components such as plugs, seals, springs, pistons, plates, and housings. Personal protective equipment is recommended when removing parts with stored spring energy. Tools include lifting devices, bolts, nuts, and specialized pullers and presses. Drained fluids must be contained and disposed of properly.
Caterpillar Cat 349E L Excavator (Prefix MPZ) Service Repair Manual (MPZ00001...jdksmmdmdd
This document provides instructions for removing and installing a crankshaft vibration damper and pulley on a 349E L excavator. The procedure involves removing the fan drive, support brackets, drive belt, and bolts securing the pulley assembly. Tooling such as guide studs is used to support the pulley assembly during removal. The installation procedure is the reverse of removal. Proper torque is applied to the securing bolts.
This document provides instructions for disassembling and assembling the travel motor on a 349E excavator. The disassembly process includes 27 steps to remove components like the head assembly, brake housing, rotating group, barrel assembly and more. The assembly process reverses the disassembly with 13 steps like installing seals, springs, pistons and plates in the proper order and orientation. Precise torques and specifications are provided to ensure correct reassembly.
Caterpillar Cat 349D2 L Excavator (Prefix RAN) Service Repair Manual (RAN0000...jdksmmdmdd
The document provides instructions for disassembling and assembling a travel motor. It lists the required tools and gives step-by-step instructions to remove components such as the head, plates, seals, pistons, and housing. Precautions are provided to keep parts clean and in correct orientation during reassembly.
This document provides instructions for removing and installing the rear gear group on a 349D2 and 349D2 L excavator powered by a C13 engine. The removal procedure involves 11 steps including removing bolts, gears, seals, bushings and bearings. The installation procedure involves 12 steps including lowering temperatures of bearings before installation, applying sealant to bolts, and ensuring proper dimensions are met. Tools including drivers and installer are required.
The document provides instructions for disassembling a travel motor. It lists the required tools and gives step-by-step instructions to remove parts like the head, plates, seals, pins, and more. Safety notices are included to handle parts carefully and avoid contamination when disassembling components.
More Related Content
Similar to Caterpillar Cat 315C L Excavator (Prefix CJC) Service Repair Manual (CJC00001 and up).pdf
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It lists 28 steps for disassembly, which include removing bolts, valves, seals, bearings, pistons, and other components. It then lists 27 steps for reassembly in reverse order, noting to clean parts thoroughly, replace all seals and gaskets, and apply a light film of oil before assembling components. Precautions are provided for parts under spring pressure.
Caterpillar Cat 315C L Excavator (Prefix CFT) Service Repair Manual Instant D...kubei069369925
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It describes 27 steps to disassemble the motor by removing components like bolts, seals, bearings, pistons, springs and plates. It then describes 26 steps for reassembling the motor by installing these components in the reverse order. Precautions are provided to mark parts, clean them, apply lubricants and take care when removing or installing parts with spring forces.
Caterpillar Cat 315C L Excavator (Prefix CFT) Service Repair Manual (CFT00001...fuusejkddmmd3e
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It lists 28 steps for disassembly, which include removing bolts, valves, seals, bearings, pistons, and other components. It then lists 27 steps for reassembly in reverse order, noting to clean parts thoroughly, replace all seals and gaskets, and apply a light film of oil before assembling components. Precautions are provided for parts under spring pressure.
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It lists 28 steps for disassembly, which include removing bolts, valves, seals, bearings, pistons, and other components. It then lists 27 steps for reassembly in reverse order, noting to clean parts thoroughly, replace all seals and gaskets, and apply a light film of oil before assembling components. Precautions are provided for parts under spring pressure.
Caterpillar cat 315 c excavator (prefix cft) service repair manual (cft00001 ...dkdmidkkdk
This document provides instructions for disassembling and assembling the travel motor on 315C and 315C L Excavator models. The disassembly process involves 27 steps to remove components like the traction control valve, travel motor, piston motor, brake pack, pistons, and bearings. The assembly process reverses the disassembly with 23 steps and cautions to clean parts, replace seals and gaskets, apply lubricant, and heat/cool components for proper installation. Proper tooling and following all steps is important to prevent damage during disassembly and assembly.
Caterpillar Cat 315C L Excavator (Prefix CFT) Service Repair Manual (CFT00001...dujkdksmdmdm
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It lists 28 steps for disassembly, which include removing bolts, valves, seals, bearings, pistons, and other components. It then lists 25 steps for reassembly in reverse order, noting to clean parts thoroughly, replace all seals and gaskets, and apply a light film of oil before assembling components. Precautions are provided for parts under spring force.
This document provides instructions for disassembling and assembling the travel motor on 315C and 315C L Excavator models. The disassembly process involves 27 steps to remove components like the traction control valve, travel motor, piston motor, brake pack, pistons, and bearings. The assembly process reverses the disassembly with 23 steps and cautions to clean parts, replace seals and gaskets, apply lubricant, and heat/cool components for proper installation. Proper tooling and following all steps is important to prevent damage during disassembly and assembly.
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It describes 27 steps to disassemble the motor by removing components like bolts, seals, bearings, pistons, springs and plates. It then describes 26 steps for reassembling the motor by installing these components in the reverse order. Precautions are provided to mark parts, clean them, apply lubricants and take care when removing or installing parts with spring forces.
Similar to Caterpillar Cat 315C L Excavator (Prefix CJC) Service Repair Manual (CJC00001 and up).pdf (8)
The document provides instructions for removing and installing various components of an excavator engine, including the combustion head, ARD nozzle heater relay, ARD fuel solenoid valve, and exhaust manifold. The procedures include required tools, safety warnings, step-by-step instructions, and torque specifications for reinstallation.
This document provides disassembly instructions for a 336D2 excavator travel motor. It outlines 27 steps to fully disassemble the travel motor. These include removing the motor head assembly, piston assemblies, barrel assembly, springs, seals, plates, and other internal components. Tools required include bolting fixtures, pry bars, pullers, and seal removal tools. Precautions are provided to retain component positioning for reassembly and to contain hydraulic fluids.
This document provides disassembly instructions for the travel motor on a 336F L XE excavator. It lists 27 steps to fully disassemble the travel motor, including removing the head, springs, relief valves, pistons, barrel assembly, swashplate and other internal components. Detailed illustrations accompany each step to show how to properly remove parts and note their positions for reassembly. Safety precautions are provided to warn of potential spring forces and contain fluids during disassembly.
Caterpillar Cat 336F L XE Excavator (Prefix MTW) Service Repair Manual (MTW00...jdksmmdmdd
This document provides disassembly instructions for a travel motor on a 336F LN XE excavator. It lists 27 steps to fully disassemble the travel motor, including removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals, and more. Detailed illustrations accompany each step to show how to remove each part in the proper sequence. Safety precautions are provided to warn of potential spring forces and contain fluids during disassembly. Required tools are listed that will be needed to complete the process.
Caterpillar Cat 336F L XE Excavator (Prefix YBH) Service Repair Manual (YBH00...jdksmmdmdd
This document provides instructions for disassembling the travel motor on a 336F LNXE excavator. The 27 step procedure includes removing components like the motor head assembly, barrel assembly, piston assemblies, springs, seals, plates and more. Special care must be taken when removing components under spring pressure. Tools and safety precautions are listed for each step. The goal is to disassemble all parts while keeping them organized for proper reassembly.
This document provides instructions to disassemble a travel motor on a 349F and 349F L excavator. It outlines 27 steps to fully disassemble the travel motor, removing components like the motor head assembly, port plate, springs, seals, bearings, valves and more. Precautions are provided to be aware of parts under spring force. Various specialized tools are required to properly support, attach, extract and remove components from the motor.
Caterpillar Cat 349E L Excavator (Prefix FJB) Service Repair Manual (FJB00001...jdksmmdmdd
The document provides instructions for disassembling and assembling a hydraulic fan drive for an excavator. It details 22 steps for disassembly, removing components like bolts, retainers, seals, discs, and housing pieces. It then details 14 steps for reassembly, including pressing in bearings and seals, installing retaining rings, and pressing the shaft assembly back into place using the proper tools. Cleanliness is emphasized throughout to prevent contamination of precision components.
Caterpillar Cat 349E L Excavator (Prefix KFX) Service Repair Manual (KFX00001...jdksmmdmdd
The document provides instructions for disassembling and assembling a travel motor on a 349E L VG excavator. It includes 27 steps for disassembly and 18 steps for assembly. Key parts that are removed and installed include the head assembly, brake housing, rotating group, barrel assembly, pistons, bearings and seals. Tools and torque specifications are provided for correct disassembly and reassembly.
The document provides step-by-step instructions to disassemble a travel motor on an excavator model 349F L. It details 27 steps to remove components such as plugs, seals, springs, pistons, plates, and housings. Personal protective equipment is recommended when removing parts with stored spring energy. Tools include lifting devices, bolts, nuts, and specialized pullers and presses. Drained fluids must be contained and disposed of properly.
Caterpillar Cat 349E L Excavator (Prefix MPZ) Service Repair Manual (MPZ00001...jdksmmdmdd
This document provides instructions for removing and installing a crankshaft vibration damper and pulley on a 349E L excavator. The procedure involves removing the fan drive, support brackets, drive belt, and bolts securing the pulley assembly. Tooling such as guide studs is used to support the pulley assembly during removal. The installation procedure is the reverse of removal. Proper torque is applied to the securing bolts.
This document provides instructions for disassembling and assembling the travel motor on a 349E excavator. The disassembly process includes 27 steps to remove components like the head assembly, brake housing, rotating group, barrel assembly and more. The assembly process reverses the disassembly with 13 steps like installing seals, springs, pistons and plates in the proper order and orientation. Precise torques and specifications are provided to ensure correct reassembly.
Caterpillar Cat 349D2 L Excavator (Prefix RAN) Service Repair Manual (RAN0000...jdksmmdmdd
The document provides instructions for disassembling and assembling a travel motor. It lists the required tools and gives step-by-step instructions to remove components such as the head, plates, seals, pistons, and housing. Precautions are provided to keep parts clean and in correct orientation during reassembly.
This document provides instructions for removing and installing the rear gear group on a 349D2 and 349D2 L excavator powered by a C13 engine. The removal procedure involves 11 steps including removing bolts, gears, seals, bushings and bearings. The installation procedure involves 12 steps including lowering temperatures of bearings before installation, applying sealant to bolts, and ensuring proper dimensions are met. Tools including drivers and installer are required.
The document provides instructions for disassembling a travel motor. It lists the required tools and gives step-by-step instructions to remove parts like the head, plates, seals, pins, and more. Safety notices are included to handle parts carefully and avoid contamination when disassembling components.
Caterpillar Cat 349D2 L Excavator (Prefix GAX) Service Repair Manual (GAX0000...jdksmmdmdd
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, seals, and pins. It then lists 31 steps for assembly, reinstalling these components in reverse order and noting to clean all parts and replace seals and gaskets. Precautions are provided to contain fluids, mark parts locations, and avoid contaminating the hydraulic system.
The document provides instructions for removing and installing various components of an excavator engine, including the combustion head, ARD nozzle heater relay, ARD fuel solenoid valve, and exhaust manifold. The procedures include required tools, safety warnings, step-by-step instructions, and torque specifications for reinstallation.
This document provides instructions for removing and installing various engine components on a C13 engine, including:
1. Removing the rear gear group by removing bolts, seals, gears, bushings, and bearings.
2. Removing the flywheel by attaching lifting tools and removing bolts.
3. Removing the crankshaft rear seal by removing bolts. Detailed steps and illustrations are provided for each procedure. Required tools are listed.
This document provides instructions for disassembling and assembling a travel motor. It begins with removing external components like plates and seals. It then describes removing the head, brake piston, disks, and rotating group. Components like the shaft, bearings, and pistons are then removed from the rotating group. Reassembly involves reversing these steps and ensuring components like O-rings and washers are properly installed. Precautions are provided to prevent contamination and correctly identify parts.
Caterpillar Cat 336D2 L Excavator (Prefix FAJ) Service Repair Manual (FAJ0000...jdksmmdmdd
This document provides disassembly instructions for a travel motor on a 336D2 excavator. It lists 27 steps to fully disassemble the travel motor, including removing components like the motor head assembly, piston assemblies, springs, seals, and plates. Special care must be taken when removing or handling components with stored spring energy to avoid personal injury. Tools required include bolting fixtures, pry bars, pullers, and seal removal tools.
This document provides instructions for disassembling the travel motor on 336D2 XE and 336D2 LXE excavator models. It outlines 27 steps to remove parts like the motor head assembly, springs, pistons, seals, plates and other components. Various tools are required including bolts, retaining ring pliers, drivers and pullers. Precautions are mentioned to relieve spring pressure safely and contain fluids. The process yields individual parts to allow inspection and replacement of worn items.
Real-time driver monitoring is one of the easiest ways to make fleet management efficient as well as seamless. Connected vehicle solutions such as fleet GPS trackers and associated software help businesses in several ways. Refer to the post below for more details.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315C EXCAVATOR CJC
Configuration: 315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Engine
Disassembly and Assembly
315C Excavator Machine Systems
Media Number -RENR5525-05 Publication Date -01/11/2008 Date Updated -10/11/2008
i01959727
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
B 1P-0074 Slide Hammer 1
C 9S-9152 Bearing Puller 1
D
1U-9895 Crossblock 1
3H-0465 Push-Puller Plate 2
8T-0649 Bolt 2
9X-8257 Washer 2
E 5P-0975 Plate 1
Start By:
a. Remove the piston motor (travel). Refer to Disassembly and Assembly, "Piston Motor
(Travel) - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
1/12
315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Engine...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
Note: Put identification marks on the motor and on all hose assemblies for installation purposes
and for the purpose of orientation. Plug all hose assemblies. This will help to prevent fluid loss
and this helps to keep contaminants from entering the system.
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
Illustration 1 g00779154
1. Remove bolts (1).
Illustration 2 g00779159
2/12
315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Engine...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 2. Remove bolts (2) from the traction control valve in order to install Tooling (A).
Illustration 3 g00779163
3. Remove traction control valve (3) and travel motor (4) from the final drive.
Illustration 4 g00779215
4. Remove Tooling (A). Remove four bolts (2). Remove traction control valve (3).
Illustration 5 g01018464
5. Remove socket head bolts (5). Remove O-ring seal (6) and O-ring seals (7). Remove head
(8).
3/12
315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Engine...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 6 g00779238
6. Remove shim (9).
Illustration 7 g00779248
7. Remove bearing (10).
Illustration 8 g00779259
8. Remove plugs (11) and the O-ring seals.
4/12
315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Engine...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 9 g01018466
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
9. Remove adapter (14) and the O-ring seal. Remove spool (13) and spring (12) from head (8).
Illustration 10 g00779279
10. Remove washer set (15).
5/12
315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Engine...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 11 g00779289
11. Remove port plate (16).
Illustration 12 g00780482
Illustration 13 g01020385
12. Remove three small O-ring seals (17). Install Tooling (D) and Tooling (E), as shown.
Tooling (E) provides a protective cover for the barrel assembly. Tooling (E) prevents
Tooling (D) from damaging the surface of the barrel assembly.
6/12
315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Engine...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. 13. Retain piston (18) with Tooling (D) and apply approximately 517 kPa (75 psi) of shop air
pressure to brake release port (Y). Brake piston (18) will move out of the piston guide.
Remove brake piston (18) from the main housing.
Illustration 14 g00779307
14. Remove O-ring seal (19) and the backup ring and remove O-ring seal (20) and the backup
ring.
Illustration 15 g00779310
15. Remove piston guide (21). Remove O-ring seal (22).
Illustration 16 g00779341
7/12
315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Engine...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 16. Remove O-ring seal (23) and backup ring (24).
Illustration 17 g00779343
17. Lay the travel motor housing on one side in order to remove rotating group (25) and brake
pack (26) as a unit.
Illustration 18 g00780107
18. Remove brake pack (26).
Illustration 19 g00780290
8/12
315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Engine...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. NOTICE
In order to ensure that each piston assembly is installed into its original
bore, identify and mark each piston assembly, retaining plate and the
barrel before removing the piston assembly.
To avoid damage to the barrel assembly parts, do not allow the parts to
separate from the assembly during removal or installation.
19. Remove pistons (27) and retainer plate (28) from barrel (29) as a unit. Separate the pistons
from the retainer plate.
Illustration 20 g00780317
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
20. Remove guide (30), spacer (31), and nine springs (32) from the barrel.
9/12
315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Engine...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 21 g00780328
21. Remove swashplate (33).
Illustration 22 g00780348
22. Use a magnet in order to remove keys (34) and pistons (35).
Illustration 23 g00780352
23. Use a magnet in order to remove pins (36).
10/12
315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Eng...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 24 g00780345
24. Remove shaft assembly (37). Remove plugs (38) and the O-ring seals.
Illustration 25 g01020388
25. Use Tooling (B) in order to remove seal (39).
Illustration 26 g00780494
26. Remove retaining rings (40) from each side of the bearing.
11/12
315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Eng...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 27 g00780502
27. Use a suitable press in order to remove bearing assembly (41) from shaft (42).
Illustration 28 g00780544
28. Use a suitable press and Tooling (C) in order to remove inner race (43) from shaft (42).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Oct 31 09:01:07 UTC+0800 2020
12/12
315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Eng...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315C EXCAVATOR CJC
Configuration: 315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Engine
Disassembly and Assembly
315C Excavator Machine Systems
Media Number -RENR5525-05 Publication Date -01/11/2008 Date Updated -10/11/2008
i01959745
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
F 1P-0510 Driver Group 1
G 206-3689 Turning Tool 1
H 5P-0960 Molybdenum Grease 1
Note: Replace all O-ring seals and gaskets. Apply a light film of "10W" oil to all components
before assembly.
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
1/13
315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Engine...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 1 g00780677
1. Raise the temperature of inner race (43). Lower the temperature of shaft (42). Use a soft
hammer in order to install inner race (43) on shaft (42).
Illustration 2 g00780698
2. Raise the temperature of bearing assembly (41). Lower the temperature of shaft (42). Install
bearing assembly (41) on shaft (42).
Illustration 3 g00780494
3. Install retaining rings (40) on each side of the bearing.
2/13
315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Engine...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 4 g01018474
4. Use Tooling (F) in order to install seal (39).
Illustration 5 g00780715
5. Use a soft hammer in order to install shaft assembly (37).
Illustration 6 g00780723
6. Install plugs (38) and the O-ring seals. Tighten plugs (38) to a torque of 140 ± 14 N·m
(103 ± 10 lb ft).
3/13
315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Engine...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 7 g00780352
7. Use a magnet in order to install pins (36).
Illustration 8 g00780839
NOTICE
The locating pin on each key is not centered. In order to prevent
damage to the barrel assembly during assembly of the travel motor, the
keys must be installed as shown. Also, the keys must be installed in the
key's original location in the body of the travel motor.
8. Install pistons (34) and keys (35).
4/13
315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Engine...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 9 g00780328
9. Install swashplate (33).
Illustration 10 g00780317
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
10. Install nine springs (32), spacer (31), and guide (30) into the barrel.
5/13
315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Engine...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 11 g00780290
11. Install pistons (27) into the retainer plate (28). Install pistons (27) and retainer plate (28) as
a unit into barrel (29) .
Note: Use string in order to keep the rotating group from separating during installation.
Illustration 12 g00780870
12. Install rotating group (25).
Illustration 13 g00780887
13. Install brake pack (26).
6/13
315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Engine...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 14 g00780817
14. Install O-ring seal (23) and backup ring (24) on piston guide (21).
Illustration 15 g00779310
15. Install piston guide (21). Install O-ring seal (22).
7/13
315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Engine...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 16 g00779307
16. Install O-ring seal (19) and the backup ring and install O-ring seal (20) and the backup ring.
Illustration 17 g00797765
Note: Make sure that brake piston (18) is thoroughly clean and free of dirt and debris.
17. Install three small O-ring seals (17). Install piston (18).
Illustration 18 g00779289
18. Install port plate (16).
8/13
315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Engine...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 19 g00779279
19. Install washer set (15).
Illustration 20 g01018466
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
20. Install spring (12) and spool (13) into head (8). Install adapter (14) and the O-ring seal into
head (8).
Illustration 21 g00779259
21. Install plugs (11) and the O-ring seals.
9/13
315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Engine...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. Illustration 22 g00779248
22. Lower the temperature of bearing (10) and install bearing (10).
Illustration 23 g00779238
23. Use a shim or shims (9) so that the following requirements are met.
Note: During the following checks, turn the travel motor output shaft in a clockwise
direction.
Illustration 24 g01018475
10/13
315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Eng...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. a. Use Tooling (G) in order to turn the output shaft. The travel motor output shaft does
not rotate with an applied torque of 440 N·m (325 lb ft) with the parking brake release
port open.
Illustration 25 g01018476
b. Apply the air pressure at orifice (X). Use Tooling (G) in order to turn the output shaft
when the parking brake release port is pressurized to 780 kPa (115 psi). Perform this
procedure with the inlet port and the outlet port open to the hydraulic oil tank. The
travel motor output shaft rotates with an applied torque of 29 N·m (21 lb ft) or less.
Note: It may be necessary to remove head (8) several times in order to determine the correct
thickness of shim or shims (9) that are used to adjust the rolling torque of the travel motor
output shaft.
24. Apply a thin layer of Tooling (H) on shim or shims (9). Install the shim or shims on the
head. The grease will hold the shim or shims in place during the installation of the head.
Install the head on the body of the travel motor.
Illustration 26 g01018464
NOTICE
To prevent possible damage to the travel motor, fill the unit with oil at
least to the fill port before operating the machine. Refer to the
Operation and Maintenance Manual for the correct oil specification.
11/13
315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Eng...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. 25. Install O-ring seal (6) and O-ring seals (7). Install head (8 ). Install socket head bolts (5).
Tighten bolts (5) to a torque of 177 ± 18 N·m (131 ± 13 lb ft).
Illustration 27 g00779215
26. Install Tooling (A). Install traction control valve (3). Remove Tooling (A). Install six bolts
(2). Tighten bolts (2) to a torque of 80 ± 8 N·m (59 ± 6 lb ft).
Illustration 28 g00779163
27. Install traction control valve (3) and travel motor (4) into the final drive as a unit.
12/13
315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Eng...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...