This document provides instructions for disassembling and assembling the travel motor of 315C and 315C L excavators. The disassembly process involves 28 steps to remove components like bolts, seals, springs, pistons, and bearings. The assembly process reverses the disassembly steps and includes precautions like cleaning parts, applying lubricant, and ensuring proper placement of springs, seals and other components. Tools required include link brackets, slide hammers, bearing pullers, drivers and turning tools.
The document provides instructions for disassembling and assembling the travel motor of a 315C excavator. Key steps include:
1. Removing the travel motor by taking out bolts and disconnecting hoses.
2. Dismantling the motor by removing components like the port plate, pistons, springs, and bearings.
3. Cleaning all parts thoroughly before assembly.
The assembly procedure lists installing components in reverse order and applying lubricants between parts. Proper cleaning and replacement of seals and gaskets is emphasized.
Caterpillar Cat 315C L Excavator (Prefix CFT) Service Repair Manual (CFT00001...tuzhiyou2
The document provides instructions for disassembling and assembling the travel motor of a 315C excavator. Key steps include:
1. Removing the travel motor by taking out bolts and disconnecting hoses.
2. Dismantling the motor housing and internal components like pistons, springs, and seals.
3. Cleaning all parts thoroughly before inspection and replacing any worn components.
4. Reassembling the motor in reverse order, applying lubricant and ensuring all seals and gaskets are replaced.
Caterpillar Cat 315C L Excavator (Prefix CFT) Service Repair Manual (CFT00001...jse7039222
The document provides instructions for disassembling and assembling the travel motor of a 315C excavator. It lists 28 steps for disassembly, beginning with removing the piston motor and ending by using tools to remove bearings. It then lists 27 steps for assembly in reverse order, including cleaning parts, applying grease, and ensuring proper installation of seals and springs. The instructions emphasize cleanliness and using identification marks to ensure correct reinstallation of components.
The document provides instructions for disassembling and assembling the travel motor of a 315C excavator. It lists 28 steps for disassembly, which include removing bolts, seals, plates, springs and other components. The 27 steps for assembly describe installing these same parts in reverse order, noting that all seals and gaskets should be replaced and components lubricated before assembly. Cleanliness is emphasized throughout to prevent contamination.
The document provides instructions for disassembling and assembling the travel motor of a 315C excavator. It lists 28 steps for disassembly, beginning with removing the piston motor and ending by using tools to remove bearings. It then lists 27 steps for assembly in reverse order, including cleaning parts, applying grease, and ensuring proper installation of seals and springs. The goal is to take apart and rebuild the travel motor while maintaining cleanliness and installing all parts correctly.
Caterpillar Cat 315C L Excavator (Prefix CFT) Service Repair Manual (CFT00001...lituo39419496
The document provides instructions for disassembling and assembling the travel motor of a 315C excavator. Key steps include:
1. Removing the travel motor by taking out bolts and disconnecting hoses.
2. Dismantling the motor housing and internal components like pistons, springs, and seals.
3. Cleaning all parts thoroughly before inspection and replacing any worn components.
4. Reassembling the motor in reverse order, applying grease to seals and torqueing bolts to specified values.
Caterpillar Cat 315C L Excavator (Prefix AKE) Service Repair Manual (AKE00001...tuzhiyou2
The document provides instructions for disassembling and assembling a travel motor. It lists 28 steps for disassembly that include removing bolts, seals, springs, and other components. It then lists 27 steps for assembly in reverse order, noting to clean parts, replace seals, and apply lubricant. Tools required include link brackets, pullers, drivers and grease. Precautions are provided to mark parts, contain fluids, and wear protective equipment when working with pressurized components.
This document provides instructions for disassembling and assembling the travel motor on 315C and 315C L excavator models. The disassembly process involves removing 27 parts from the travel motor in a specific sequence. The assembly process reverses the disassembly steps, applying grease and ensuring cleanliness during reinstallation of parts. Proper tools are required for tasks like pressing bearings.
The document provides instructions for disassembling and assembling the travel motor of a 315C excavator. Key steps include:
1. Removing the travel motor by taking out bolts and disconnecting hoses.
2. Dismantling the motor by removing components like the port plate, pistons, springs, and bearings.
3. Cleaning all parts thoroughly before assembly.
The assembly procedure lists installing components in reverse order and applying lubricants between parts. Proper cleaning and replacement of seals and gaskets is emphasized.
Caterpillar Cat 315C L Excavator (Prefix CFT) Service Repair Manual (CFT00001...tuzhiyou2
The document provides instructions for disassembling and assembling the travel motor of a 315C excavator. Key steps include:
1. Removing the travel motor by taking out bolts and disconnecting hoses.
2. Dismantling the motor housing and internal components like pistons, springs, and seals.
3. Cleaning all parts thoroughly before inspection and replacing any worn components.
4. Reassembling the motor in reverse order, applying lubricant and ensuring all seals and gaskets are replaced.
Caterpillar Cat 315C L Excavator (Prefix CFT) Service Repair Manual (CFT00001...jse7039222
The document provides instructions for disassembling and assembling the travel motor of a 315C excavator. It lists 28 steps for disassembly, beginning with removing the piston motor and ending by using tools to remove bearings. It then lists 27 steps for assembly in reverse order, including cleaning parts, applying grease, and ensuring proper installation of seals and springs. The instructions emphasize cleanliness and using identification marks to ensure correct reinstallation of components.
The document provides instructions for disassembling and assembling the travel motor of a 315C excavator. It lists 28 steps for disassembly, which include removing bolts, seals, plates, springs and other components. The 27 steps for assembly describe installing these same parts in reverse order, noting that all seals and gaskets should be replaced and components lubricated before assembly. Cleanliness is emphasized throughout to prevent contamination.
The document provides instructions for disassembling and assembling the travel motor of a 315C excavator. It lists 28 steps for disassembly, beginning with removing the piston motor and ending by using tools to remove bearings. It then lists 27 steps for assembly in reverse order, including cleaning parts, applying grease, and ensuring proper installation of seals and springs. The goal is to take apart and rebuild the travel motor while maintaining cleanliness and installing all parts correctly.
Caterpillar Cat 315C L Excavator (Prefix CFT) Service Repair Manual (CFT00001...lituo39419496
The document provides instructions for disassembling and assembling the travel motor of a 315C excavator. Key steps include:
1. Removing the travel motor by taking out bolts and disconnecting hoses.
2. Dismantling the motor housing and internal components like pistons, springs, and seals.
3. Cleaning all parts thoroughly before inspection and replacing any worn components.
4. Reassembling the motor in reverse order, applying grease to seals and torqueing bolts to specified values.
Caterpillar Cat 315C L Excavator (Prefix AKE) Service Repair Manual (AKE00001...tuzhiyou2
The document provides instructions for disassembling and assembling a travel motor. It lists 28 steps for disassembly that include removing bolts, seals, springs, and other components. It then lists 27 steps for assembly in reverse order, noting to clean parts, replace seals, and apply lubricant. Tools required include link brackets, pullers, drivers and grease. Precautions are provided to mark parts, contain fluids, and wear protective equipment when working with pressurized components.
This document provides instructions for disassembling and assembling the travel motor on 315C and 315C L excavator models. The disassembly process involves removing 27 parts from the travel motor in a specific sequence. The assembly process reverses the disassembly steps, applying grease and ensuring cleanliness during reinstallation of parts. Proper tools are required for tasks like pressing bearings.
Caterpillar Cat 315C L Excavator (Prefix AKE) Service Repair Manual (AKE00001...jse7039222
This document provides instructions for disassembling and assembling the travel motor on 315C and 315C L excavator models. The disassembly process involves removing 27 parts from the travel motor in a specific sequence. The assembly process reverses the disassembly steps, applying grease and ensuring cleanliness during reinstallation of the 27 parts back into the travel motor. Proper tools are required for tasks like pressing bearings.
The document provides instructions for disassembling and assembling a travel motor. It lists 28 steps for disassembly that include removing bolts, seals, springs, and other components. It then lists 27 steps for assembly in reverse order, noting to clean parts, replace seals, and apply lubricant. Tools required include link brackets, pullers, drivers and grease. Precautions are provided to mark parts, contain fluids, and wear protective equipment when working with pressurized components.
Caterpillar Cat 315C L Excavator (Prefix AKE) Service Repair Manual (AKE00001...lituo39419496
The document provides instructions for disassembling and assembling a travel motor. It lists 28 steps for disassembly that include removing bolts, seals, springs, and other components. It then lists 27 steps for assembly in reverse order, noting to clean parts, replace seals, and apply lubricant. Tools required include link brackets, pullers, drivers and grease. Precautions are provided to mark parts, contain fluids, and wear protective equipment when working with pressurized components.
The document provides instructions for disassembling and assembling a travel motor. It lists 28 steps for disassembly that include removing bolts, seals, springs, and other components. It then lists 27 steps for assembly in reverse order, noting to clean parts, replace seals, and apply lubricant. Tools required include link brackets, pullers, drivers and grease. Safety precautions are provided around releasing spring forces and ensuring cleanliness during maintenance.
The document provides step-by-step instructions for disassembling and assembling the travel motor on 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, replace seals, and apply lubricant. Precautions are given to identify parts, contain fluids, and be aware of spring forces during disassembly and assembly.
The document provides step-by-step instructions for disassembling and assembling the travel motor of 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, replace seals, and apply lubricant. Precautions are given to identify parts, contain fluids, and be aware of spring forces during disassembly and assembly.
Caterpillar Cat 315C L Excavator (Prefix CJC) Service Repair Manual (CJC00001...fuusejkddmmd3e
The document provides step-by-step instructions for disassembling and assembling the travel motor of 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. It then lists 27 steps for reassembly in reverse order, noting to clean parts, replace seals, apply lubricant and heat components as needed. Precautions are provided to prevent injury from spring forces and properly identify parts during disassembly and reassembly.
The document provides step-by-step instructions for disassembling and assembling the travel motor on 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, replace seals, and apply lubricant. Precautions are given to identify parts, contain fluids, and be aware of spring forces during disassembly and assembly.
Caterpillar Cat 315C L Excavator (Prefix CJC) Service Repair Manual (CJC00001...jdksmmdmdd
The document provides step-by-step instructions for disassembling and assembling the travel motor of 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, replace seals, and apply lubricant. Precautions are given to identify parts, contain fluids, and be aware of spring forces during disassembly and assembly.
Caterpillar Cat 315C L Excavator (Prefix CJC) Service Repair Manual (CJC00001...orrf0370383
The document provides step-by-step instructions for disassembling and assembling the travel motor on 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, replace seals, and apply lubricant. Precautions are given to identify parts, contain fluids, and be aware of spring forces during disassembly and assembly.
Caterpillar Cat 315C L Excavator (Prefix CJC) Service Repair Manual (CJC00001...fujkse9didkke3
This document provides instructions for disassembling and assembling the travel motor on 315C and 315C L Excavator models. The disassembly process involves 28 steps to remove components like bolts, valves, seals, pistons, springs, and bearings. The assembly process reverses the disassembly with 27 steps, applying grease and torque specifications, and includes heating and pressing components during installation. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar Cat 315C L Excavator (Prefix CJC) Service Repair Manual (CJC00001...dujkdksmdmdm
The document provides step-by-step instructions for disassembling and assembling the travel motor of 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, replace seals, and apply lubricant. Precautions are given to identify parts, contain fluids, and be aware of spring forces during disassembly and assembly.
Caterpillar cat 315 c l excavator (prefix cjc) service repair manual (cjc0000...dkdmidkkdk
This document provides instructions for disassembling and assembling the travel motor on 315C and 315C L Excavator models. The disassembly process involves 28 steps to remove components like bolts, valves, seals, pistons, springs, and bearings. The assembly process reverses the disassembly with 27 steps, applying grease and torque specifications, and includes heating and pressing components during installation. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar Cat 315C L Excavator (Prefix CJC) Service Repair Manual Instant D...rishang96299
The document provides step-by-step instructions for disassembling and assembling the travel motor of 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, apply lubricants, and properly set bearing temperatures and torque specifications. Safety notices are included throughout to warn of spring forces and contain fluids.
Caterpillar Cat 315C L Excavator (Prefix CJC) Service Repair Manual Instant D...kubei069369925
The document provides step-by-step instructions for disassembling and assembling the travel motor on 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, replace seals, and apply lubricant. Precautions are given to identify parts, contain fluids, and be aware of spring forces during disassembly and assembly.
This document provides instructions for disassembling and assembling the travel motor on 315C and 315C L Excavator models. The disassembly process involves 28 steps to remove components like bolts, valves, seals, pistons, springs, and bearings. The assembly process reverses the disassembly with 27 steps, applying grease and torque specifications, and includes heating and pressing components during installation. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar cat 315 c excavator (prefix cjc) service repair manual (cjc00001 ...dkdmidkkdk
The document provides step-by-step instructions for disassembling and assembling the travel motor on 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, replace seals, and apply lubricant. Precautions are given to identify parts, contain fluids, and be aware of spring forces during disassembly and assembly.
The document provides step-by-step instructions for disassembling and assembling the travel motor on 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, replace seals, and apply lubricant. Precautions are given to identify parts, contain fluids, and be aware of spring forces during disassembly and assembly.
The document provides step-by-step instructions for disassembling and assembling the travel motor of 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, replace seals, and apply lubricants. Special tools and safety precautions are noted throughout.
Caterpillar Cat 315C L Excavator (Prefix CJC) Service Repair Manual Instant D...shanruliu7360
The document provides step-by-step instructions for disassembling and assembling the travel motor of 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, replace seals, and apply lubricant. Precautions are given to identify parts, contain fluids, and be aware of spring forces during disassembly and assembly.
1. The document provides removal and installation instructions for a fuel injection pump on a 320DL excavator with a C6.4 engine.
2. The procedure describes disconnecting fuel lines and harness assemblies, removing mounting hardware, and using identification marks to ensure proper installation orientation.
3. Cleanliness is emphasized and special tools are required to disconnect the high pressure fuel lines before the pump can be removed from the engine.
Caterpillar Cat 320D2 L Excavator (Prefix DNP) Service Repair Manual (DNP0000...jse7039222
The document provides assembly and disassembly instructions for components of a 320D2 excavator, including:
- Assembling the swing drive by installing bearings, seals, gears, and housings in 22 steps.
- Removing the swing gear and bearing by lifting it from the undercarriage frame after removing bolts and seals in 6 steps.
- Providing tools, illustrations and safety notes for the procedures.
More Related Content
Similar to Caterpillar Cat 315C Excavator (Prefix CJC) Service Repair Manual (CJC00001 and up).pdf
Caterpillar Cat 315C L Excavator (Prefix AKE) Service Repair Manual (AKE00001...jse7039222
This document provides instructions for disassembling and assembling the travel motor on 315C and 315C L excavator models. The disassembly process involves removing 27 parts from the travel motor in a specific sequence. The assembly process reverses the disassembly steps, applying grease and ensuring cleanliness during reinstallation of the 27 parts back into the travel motor. Proper tools are required for tasks like pressing bearings.
The document provides instructions for disassembling and assembling a travel motor. It lists 28 steps for disassembly that include removing bolts, seals, springs, and other components. It then lists 27 steps for assembly in reverse order, noting to clean parts, replace seals, and apply lubricant. Tools required include link brackets, pullers, drivers and grease. Precautions are provided to mark parts, contain fluids, and wear protective equipment when working with pressurized components.
Caterpillar Cat 315C L Excavator (Prefix AKE) Service Repair Manual (AKE00001...lituo39419496
The document provides instructions for disassembling and assembling a travel motor. It lists 28 steps for disassembly that include removing bolts, seals, springs, and other components. It then lists 27 steps for assembly in reverse order, noting to clean parts, replace seals, and apply lubricant. Tools required include link brackets, pullers, drivers and grease. Precautions are provided to mark parts, contain fluids, and wear protective equipment when working with pressurized components.
The document provides instructions for disassembling and assembling a travel motor. It lists 28 steps for disassembly that include removing bolts, seals, springs, and other components. It then lists 27 steps for assembly in reverse order, noting to clean parts, replace seals, and apply lubricant. Tools required include link brackets, pullers, drivers and grease. Safety precautions are provided around releasing spring forces and ensuring cleanliness during maintenance.
The document provides step-by-step instructions for disassembling and assembling the travel motor on 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, replace seals, and apply lubricant. Precautions are given to identify parts, contain fluids, and be aware of spring forces during disassembly and assembly.
The document provides step-by-step instructions for disassembling and assembling the travel motor of 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, replace seals, and apply lubricant. Precautions are given to identify parts, contain fluids, and be aware of spring forces during disassembly and assembly.
Caterpillar Cat 315C L Excavator (Prefix CJC) Service Repair Manual (CJC00001...fuusejkddmmd3e
The document provides step-by-step instructions for disassembling and assembling the travel motor of 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. It then lists 27 steps for reassembly in reverse order, noting to clean parts, replace seals, apply lubricant and heat components as needed. Precautions are provided to prevent injury from spring forces and properly identify parts during disassembly and reassembly.
The document provides step-by-step instructions for disassembling and assembling the travel motor on 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, replace seals, and apply lubricant. Precautions are given to identify parts, contain fluids, and be aware of spring forces during disassembly and assembly.
Caterpillar Cat 315C L Excavator (Prefix CJC) Service Repair Manual (CJC00001...jdksmmdmdd
The document provides step-by-step instructions for disassembling and assembling the travel motor of 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, replace seals, and apply lubricant. Precautions are given to identify parts, contain fluids, and be aware of spring forces during disassembly and assembly.
Caterpillar Cat 315C L Excavator (Prefix CJC) Service Repair Manual (CJC00001...orrf0370383
The document provides step-by-step instructions for disassembling and assembling the travel motor on 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, replace seals, and apply lubricant. Precautions are given to identify parts, contain fluids, and be aware of spring forces during disassembly and assembly.
Caterpillar Cat 315C L Excavator (Prefix CJC) Service Repair Manual (CJC00001...fujkse9didkke3
This document provides instructions for disassembling and assembling the travel motor on 315C and 315C L Excavator models. The disassembly process involves 28 steps to remove components like bolts, valves, seals, pistons, springs, and bearings. The assembly process reverses the disassembly with 27 steps, applying grease and torque specifications, and includes heating and pressing components during installation. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar Cat 315C L Excavator (Prefix CJC) Service Repair Manual (CJC00001...dujkdksmdmdm
The document provides step-by-step instructions for disassembling and assembling the travel motor of 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, replace seals, and apply lubricant. Precautions are given to identify parts, contain fluids, and be aware of spring forces during disassembly and assembly.
Caterpillar cat 315 c l excavator (prefix cjc) service repair manual (cjc0000...dkdmidkkdk
This document provides instructions for disassembling and assembling the travel motor on 315C and 315C L Excavator models. The disassembly process involves 28 steps to remove components like bolts, valves, seals, pistons, springs, and bearings. The assembly process reverses the disassembly with 27 steps, applying grease and torque specifications, and includes heating and pressing components during installation. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar Cat 315C L Excavator (Prefix CJC) Service Repair Manual Instant D...rishang96299
The document provides step-by-step instructions for disassembling and assembling the travel motor of 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, apply lubricants, and properly set bearing temperatures and torque specifications. Safety notices are included throughout to warn of spring forces and contain fluids.
Caterpillar Cat 315C L Excavator (Prefix CJC) Service Repair Manual Instant D...kubei069369925
The document provides step-by-step instructions for disassembling and assembling the travel motor on 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, replace seals, and apply lubricant. Precautions are given to identify parts, contain fluids, and be aware of spring forces during disassembly and assembly.
This document provides instructions for disassembling and assembling the travel motor on 315C and 315C L Excavator models. The disassembly process involves 28 steps to remove components like bolts, valves, seals, pistons, springs, and bearings. The assembly process reverses the disassembly with 27 steps, applying grease and torque specifications, and includes heating and pressing components during installation. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar cat 315 c excavator (prefix cjc) service repair manual (cjc00001 ...dkdmidkkdk
The document provides step-by-step instructions for disassembling and assembling the travel motor on 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, replace seals, and apply lubricant. Precautions are given to identify parts, contain fluids, and be aware of spring forces during disassembly and assembly.
The document provides step-by-step instructions for disassembling and assembling the travel motor on 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, replace seals, and apply lubricant. Precautions are given to identify parts, contain fluids, and be aware of spring forces during disassembly and assembly.
The document provides step-by-step instructions for disassembling and assembling the travel motor of 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, replace seals, and apply lubricants. Special tools and safety precautions are noted throughout.
Caterpillar Cat 315C L Excavator (Prefix CJC) Service Repair Manual Instant D...shanruliu7360
The document provides step-by-step instructions for disassembling and assembling the travel motor of 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, replace seals, and apply lubricant. Precautions are given to identify parts, contain fluids, and be aware of spring forces during disassembly and assembly.
Similar to Caterpillar Cat 315C Excavator (Prefix CJC) Service Repair Manual (CJC00001 and up).pdf (20)
1. The document provides removal and installation instructions for a fuel injection pump on a 320DL excavator with a C6.4 engine.
2. The procedure describes disconnecting fuel lines and harness assemblies, removing mounting hardware, and using identification marks to ensure proper installation orientation.
3. Cleanliness is emphasized and special tools are required to disconnect the high pressure fuel lines before the pump can be removed from the engine.
Caterpillar Cat 320D2 L Excavator (Prefix DNP) Service Repair Manual (DNP0000...jse7039222
The document provides assembly and disassembly instructions for components of a 320D2 excavator, including:
- Assembling the swing drive by installing bearings, seals, gears, and housings in 22 steps.
- Removing the swing gear and bearing by lifting it from the undercarriage frame after removing bolts and seals in 6 steps.
- Providing tools, illustrations and safety notes for the procedures.
The document provides installation instructions for a swing gear and bearing on excavator models 320D2 and 320D2 L. It outlines 22 steps to assemble the swing drive, including installing bearings, seals, gears, housings and fasteners in the proper order. Tools and lubricants required for the installation are listed in a table. The process involves lifting and positioning heavy components weighing up to 280 kg.
This document provides instructions for removing and installing the valve mechanism cover base and rocker shaft on a 320D LRR excavator with a C6.4 engine. The removal procedure details removing clips, harnesses, nuts and bolts to detach the cover base. Installation involves cleaning parts, installing a new gasket, and reattaching with bolts. Separate sections provide steps for disassembling the rocker shaft into individual parts and reassembling it.
This document provides instructions for removing and installing the flywheel and flywheel housing on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove the flywheel, flywheel housing, rear crankshaft seal, and installing replacements. Safety notices are provided to keep parts clean and contain fluids.
This document provides instructions for removing and installing the engine oil pump and water pump on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like gears, covers, and seals. Detailed illustrations and cautions about cleaning and containing fluids are provided. Components are to be checked for wear and replaced as needed during disassembly and reassembly.
1) The document provides instructions for installing a flywheel on a Caterpillar 320 GC excavator. It describes cleaning and preparing the crankshaft, installing guide studs and lifting the flywheel into place, then bolting it securely and checking the run out.
2) Additional steps are outlined for removing and installing the crankshaft rear seal and flywheel housing. The crankshaft rear seal is press-fit as a one-piece assembly and must be replaced if removed. Dowels, gaskets and seals are also installed during flywheel housing replacement.
3) Precise torques are specified for bolts depending on their grade, and alignment of the flywheel housing to the
Caterpillar Cat 318D2 L Excavator (Prefix HAH) Service Repair Manual (HAH0000...jse7039222
This document provides instructions for disassembling the final drive of a 318D2 L excavator. It lists the required tools and presents a step-by-step process involving 31 steps. Some key steps include fastening the final drive to a repair stand, removing bolts and washers to access internal components, and using various tools to separate parts like the carrier assembly, ring gears, planetary gears, and seals from the main housing. Proper cleaning and safety precautions are noted throughout.
The document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists required tools and gives step-by-step instructions to remove components like the final drive cover, planetary assembly, retaining rings, and seals. It then describes the assembly process in reverse, including cleaning parts, replacing seals and O-rings, and torquing fasteners to the specified values. The goal is to repair or replace worn parts while maintaining cleanliness for proper functioning of the final drive.
Caterpillar Cat 318B N Excavator (Prefix 7KZ) Service Repair Manual (7KZ00001...jse7039222
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel using lifting tools and removing bolts.
- Removing the crankshaft rear seal using drilling and a slide hammer puller.
- Installing a new crankshaft rear seal by applying oil and using installer tools.
- Removing the flywheel housing by lifting and removing bolts, and installing with new gaskets and bolts.
- Removing the vibration damper and crankshaft pulley by removing bolts and nuts using sockets and pullers, and installing the pulley with a washer and nut.
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel using lifting tools and removing bolts.
- Removing the crankshaft rear seal using drilling and a slide hammer puller.
- Installing a new crankshaft rear seal by applying oil and using installer tools.
- Removing the flywheel housing by lifting and removing bolts, and installing with new gaskets and bolts.
- Removing the vibration damper and crankshaft pulley by removing bolts and nuts using sockets and pullers, and installing the pulley with a washer and nut.
Caterpillar Cat 318B L Excavator (Prefix 7KZ) Service Repair Manual (7KZ00001...jse7039222
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel using lifting tools and removing bolts.
- Removing the crankshaft rear seal using drilling and a slide hammer puller.
- Installing a new crankshaft rear seal by applying oil and using installer tools.
- Removing the flywheel housing by lifting and removing bolts, and installing with new gaskets and bolts.
- Removing the vibration damper and crankshaft pulley by removing bolts and nuts using sockets and pullers, and installing the pulley with a washer and nut.
Caterpillar Cat 315D L Excavator (Prefix NCM) Service Repair Manual (NCM00001...jse7039222
This document provides instructions for disassembling and assembling the final drive of a 315D L excavator. It describes in detail how to remove over 30 individual components of the final drive including the cover, carrier assembly, ring gears, and housing. Reassembly requires precisely installing seals, bearings, shims and other parts in the reverse order and verifying proper bearing preload using a press and micrometers. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar Cat 315D L Excavator (Prefix KBD) Service Repair Manual (KBD00001...jse7039222
This document provides instructions for disassembling and assembling the final drive of a 315D L excavator. It describes in detail how to remove over 30 individual components of the final drive including the cover, carrier assembly, ring gears, and housing pieces. Reassembly requires precisely installing new seals and bearings then measuring clearance to determine the correct shim thickness before reinstalling all components in reverse order. Cleanliness and applying lubricant to parts is emphasized throughout.
Caterpillar Cat 315D L Excavator (Prefix JHA) Service Repair Manual (JHA00001...jse7039222
The document provides step-by-step instructions for disassembling and assembling a travel motor. It lists 27 steps for disassembly, which include removing various components like the head, check valves, fittings, brake piston, piston guide, barrel assembly, and shaft assembly. It then lists 22 steps for assembly, covering installation of seals, plates, piston shoe assemblies, cam plate, springs, and other components in the reverse order of disassembly. Precautions are provided to ensure correct alignment of parts and prevent damage during assembly.
Caterpillar Cat 315D L Excavator (Prefix CJN) Service Repair Manual (CJN00001...jse7039222
This document provides instructions for disassembling and assembling the travel motor of a 315D L excavator. The disassembly process includes 27 steps to remove components like the head, barrel assembly, cam plate, shaft assembly and more. The assembly process has 24 steps and instructs technicians to thoroughly clean parts, apply lubricants, and reinstall components in their original positions and orientations. Technicians are warned to take care handling parts and aligning components properly to prevent damage.
Caterpillar Cat 315C L Excavator (Prefix CJC) Service Repair Manual (CJC00001...jse7039222
This document provides instructions for disassembling and assembling the travel motor of 315C and 315C L excavators. The disassembly process involves 28 steps to remove components like bolts, seals, springs, pistons, and bearings. The assembly process reverses the disassembly steps and includes precautions like cleaning parts, applying lubricant, and ensuring proper placement of springs, seals and other components. Tools required include link brackets, slide hammers, bearing pullers, drivers and turning tools.
Caterpillar Cat 315C L Excavator (Prefix CFB) Service Repair Manual (CFB00001...jse7039222
This document provides instructions for disassembling and assembling the final drive of a 315C excavator. The disassembly process involves removing 21 components from the final drive assembly using various tools. The assembly process describes installing the components in reverse order and determining the proper shim thickness to set the rolling torque. Precise measurements and stake marks are required to ensure correct assembly. Cleanliness is important during assembly to prevent contamination.
Caterpillar Cat 315C L Excavator (Prefix ANF) Service Repair Manual (ANF00001...jse7039222
This document provides instructions for disassembling and assembling components of the rocker shaft assembly for a Caterpillar 315C excavator engine. It describes how to disassemble the rocker shaft by removing retaining rings, washers, rocker arms, and springs. It then describes the assembly process and includes illustrations showing the components. Precautions are provided regarding spring force. The document also provides instructions for installing the rocker shaft and pushrods and adjusting valve lash clearance.
This document provides instructions for disassembling and assembling the final drive of a 315C excavator. The disassembly process involves removing 21 components from the final drive assembly using various tools. The assembly process describes installing the components in reverse order and determining the proper shim thickness to set the rolling torque. Precise measurements and stake marks are required to ensure correct assembly.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Your VW's camshaft position sensor is crucial for engine performance. Signs of failure include engine misfires, difficulty starting, stalling at low speeds, reduced fuel efficiency, and the check engine light. Prompt inspection and replacement can prevent further damage and keep your VW running smoothly.
What Is Recruitment Processing Outsourcing (RPO) Services?Impeccable HR
Impeccable HR provides a wide range of RPO services for your bulk hiring needs within a stipulated period. They meticulously build RPO solutions to improve your recruitment process. RPO services are great for budget-conscious recruiters who want high-quality personnel.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315C EXCAVATOR CJC
Configuration: 315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Engine
Disassembly and Assembly
315C Excavator Machine Systems
Media Number -RENR5525-05 Publication Date -01/11/2008 Date Updated -10/11/2008
i01959727
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
B 1P-0074 Slide Hammer 1
C 9S-9152 Bearing Puller 1
D
1U-9895 Crossblock 1
3H-0465 Push-Puller Plate 2
8T-0649 Bolt 2
9X-8257 Washer 2
E 5P-0975 Plate 1
Start By:
a. Remove the piston motor (travel). Refer to Disassembly and Assembly, "Piston Motor
(Travel) - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
1/12
315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Engine...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
Note: Put identification marks on the motor and on all hose assemblies for installation purposes
and for the purpose of orientation. Plug all hose assemblies. This will help to prevent fluid loss
and this helps to keep contaminants from entering the system.
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
Illustration 1 g00779154
1. Remove bolts (1).
Illustration 2 g00779159
2/12
315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Engine...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 2. Remove bolts (2) from the traction control valve in order to install Tooling (A).
Illustration 3 g00779163
3. Remove traction control valve (3) and travel motor (4) from the final drive.
Illustration 4 g00779215
4. Remove Tooling (A). Remove four bolts (2). Remove traction control valve (3).
Illustration 5 g01018464
5. Remove socket head bolts (5). Remove O-ring seal (6) and O-ring seals (7). Remove head
(8).
3/12
315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Engine...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 6 g00779238
6. Remove shim (9).
Illustration 7 g00779248
7. Remove bearing (10).
Illustration 8 g00779259
8. Remove plugs (11) and the O-ring seals.
4/12
315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Engine...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 9 g01018466
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
9. Remove adapter (14) and the O-ring seal. Remove spool (13) and spring (12) from head (8).
Illustration 10 g00779279
10. Remove washer set (15).
5/12
315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Engine...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 11 g00779289
11. Remove port plate (16).
Illustration 12 g00780482
Illustration 13 g01020385
12. Remove three small O-ring seals (17). Install Tooling (D) and Tooling (E), as shown.
Tooling (E) provides a protective cover for the barrel assembly. Tooling (E) prevents
Tooling (D) from damaging the surface of the barrel assembly.
6/12
315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Engine...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 13. Retain piston (18) with Tooling (D) and apply approximately 517 kPa (75 psi) of shop air
pressure to brake release port (Y). Brake piston (18) will move out of the piston guide.
Remove brake piston (18) from the main housing.
Illustration 14 g00779307
14. Remove O-ring seal (19) and the backup ring and remove O-ring seal (20) and the backup
ring.
Illustration 15 g00779310
15. Remove piston guide (21). Remove O-ring seal (22).
Illustration 16 g00779341
7/12
315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Engine...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. 16. Remove O-ring seal (23) and backup ring (24).
Illustration 17 g00779343
17. Lay the travel motor housing on one side in order to remove rotating group (25) and brake
pack (26) as a unit.
Illustration 18 g00780107
18. Remove brake pack (26).
Illustration 19 g00780290
8/12
315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Engine...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. NOTICE
In order to ensure that each piston assembly is installed into its original
bore, identify and mark each piston assembly, retaining plate and the
barrel before removing the piston assembly.
To avoid damage to the barrel assembly parts, do not allow the parts to
separate from the assembly during removal or installation.
19. Remove pistons (27) and retainer plate (28) from barrel (29) as a unit. Separate the pistons
from the retainer plate.
Illustration 20 g00780317
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
20. Remove guide (30), spacer (31), and nine springs (32) from the barrel.
9/12
315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Engine...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 21 g00780328
21. Remove swashplate (33).
Illustration 22 g00780348
22. Use a magnet in order to remove keys (34) and pistons (35).
Illustration 23 g00780352
23. Use a magnet in order to remove pins (36).
10/12
315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Eng...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 24 g00780345
24. Remove shaft assembly (37). Remove plugs (38) and the O-ring seals.
Illustration 25 g01020388
25. Use Tooling (B) in order to remove seal (39).
Illustration 26 g00780494
26. Remove retaining rings (40) from each side of the bearing.
11/12
315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Eng...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 27 g00780502
27. Use a suitable press in order to remove bearing assembly (41) from shaft (42).
Illustration 28 g00780544
28. Use a suitable press and Tooling (C) in order to remove inner race (43) from shaft (42).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Oct 31 09:01:07 UTC+0800 2020
12/12
315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Eng...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315C EXCAVATOR CJC
Configuration: 315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Engine
Disassembly and Assembly
315C Excavator Machine Systems
Media Number -RENR5525-05 Publication Date -01/11/2008 Date Updated -10/11/2008
i01959745
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
F 1P-0510 Driver Group 1
G 206-3689 Turning Tool 1
H 5P-0960 Molybdenum Grease 1
Note: Replace all O-ring seals and gaskets. Apply a light film of "10W" oil to all components
before assembly.
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
1/13
315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Engine...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 1 g00780677
1. Raise the temperature of inner race (43). Lower the temperature of shaft (42). Use a soft
hammer in order to install inner race (43) on shaft (42).
Illustration 2 g00780698
2. Raise the temperature of bearing assembly (41). Lower the temperature of shaft (42). Install
bearing assembly (41) on shaft (42).
Illustration 3 g00780494
3. Install retaining rings (40) on each side of the bearing.
2/13
315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Engine...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 4 g01018474
4. Use Tooling (F) in order to install seal (39).
Illustration 5 g00780715
5. Use a soft hammer in order to install shaft assembly (37).
Illustration 6 g00780723
6. Install plugs (38) and the O-ring seals. Tighten plugs (38) to a torque of 140 ± 14 N·m
(103 ± 10 lb ft).
3/13
315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Engine...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 7 g00780352
7. Use a magnet in order to install pins (36).
Illustration 8 g00780839
NOTICE
The locating pin on each key is not centered. In order to prevent
damage to the barrel assembly during assembly of the travel motor, the
keys must be installed as shown. Also, the keys must be installed in the
key's original location in the body of the travel motor.
8. Install pistons (34) and keys (35).
4/13
315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Engine...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 9 g00780328
9. Install swashplate (33).
Illustration 10 g00780317
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
10. Install nine springs (32), spacer (31), and guide (30) into the barrel.
5/13
315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Engine...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 11 g00780290
11. Install pistons (27) into the retainer plate (28). Install pistons (27) and retainer plate (28) as
a unit into barrel (29) .
Note: Use string in order to keep the rotating group from separating during installation.
Illustration 12 g00780870
12. Install rotating group (25).
Illustration 13 g00780887
13. Install brake pack (26).
6/13
315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Engine...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 14 g00780817
14. Install O-ring seal (23) and backup ring (24) on piston guide (21).
Illustration 15 g00779310
15. Install piston guide (21). Install O-ring seal (22).
7/13
315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Engine...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 16 g00779307
16. Install O-ring seal (19) and the backup ring and install O-ring seal (20) and the backup ring.
Illustration 17 g00797765
Note: Make sure that brake piston (18) is thoroughly clean and free of dirt and debris.
17. Install three small O-ring seals (17). Install piston (18).
Illustration 18 g00779289
18. Install port plate (16).
8/13
315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Engine...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 19 g00779279
19. Install washer set (15).
Illustration 20 g01018466
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
20. Install spring (12) and spool (13) into head (8). Install adapter (14) and the O-ring seal into
head (8).
Illustration 21 g00779259
21. Install plugs (11) and the O-ring seals.
9/13
315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Engine...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Illustration 22 g00779248
22. Lower the temperature of bearing (10) and install bearing (10).
Illustration 23 g00779238
23. Use a shim or shims (9) so that the following requirements are met.
Note: During the following checks, turn the travel motor output shaft in a clockwise
direction.
Illustration 24 g01018475
10/13
315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Eng...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. a. Use Tooling (G) in order to turn the output shaft. The travel motor output shaft does
not rotate with an applied torque of 440 N·m (325 lb ft) with the parking brake release
port open.
Illustration 25 g01018476
b. Apply the air pressure at orifice (X). Use Tooling (G) in order to turn the output shaft
when the parking brake release port is pressurized to 780 kPa (115 psi). Perform this
procedure with the inlet port and the outlet port open to the hydraulic oil tank. The
travel motor output shaft rotates with an applied torque of 29 N·m (21 lb ft) or less.
Note: It may be necessary to remove head (8) several times in order to determine the correct
thickness of shim or shims (9) that are used to adjust the rolling torque of the travel motor
output shaft.
24. Apply a thin layer of Tooling (H) on shim or shims (9). Install the shim or shims on the
head. The grease will hold the shim or shims in place during the installation of the head.
Install the head on the body of the travel motor.
Illustration 26 g01018464
NOTICE
To prevent possible damage to the travel motor, fill the unit with oil at
least to the fill port before operating the machine. Refer to the
Operation and Maintenance Manual for the correct oil specification.
11/13
315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Eng...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. 25. Install O-ring seal (6) and O-ring seals (7). Install head (8 ). Install socket head bolts (5).
Tighten bolts (5) to a torque of 177 ± 18 N·m (131 ± 13 lb ft).
Illustration 27 g00779215
26. Install Tooling (A). Install traction control valve (3). Remove Tooling (A). Install six bolts
(2). Tighten bolts (2) to a torque of 80 ± 8 N·m (59 ± 6 lb ft).
Illustration 28 g00779163
27. Install traction control valve (3) and travel motor (4) into the final drive as a unit.
12/13
315C & 315C L Excavators CJC00001-UP (MACHINE) POWERED BY 3046 Eng...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...