This document provides instructions for disassembling and assembling components of the rocker shaft assembly for a Caterpillar 315C excavator engine. It describes how to disassemble the rocker shaft by removing retaining rings, washers, rocker arms, and springs. It then describes the assembly process and includes illustrations showing the components. Precautions are provided regarding spring force. The document also provides instructions for installing the rocker shaft and pushrods and adjusting valve lash clearance.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
Learn why monitoring your Mercedes' Exhaust Back Pressure (EBP) sensor is crucial. Understand its role in engine performance and emission reduction. Discover five warning signs of EBP sensor failure, from loss of power to increased emissions. Take action promptly to avoid costly repairs and maintain your Mercedes' reliability and efficiency.
What Is Recruitment Processing Outsourcing (RPO) Services?Impeccable HR
Impeccable HR provides a wide range of RPO services for your bulk hiring needs within a stipulated period. They meticulously build RPO solutions to improve your recruitment process. RPO services are great for budget-conscious recruiters who want high-quality personnel.
How To Fix The Key Not Detected Issue In Mercedes CarsIntegrity Motorcar
Experiencing a "Key Not Detected" problem in your Mercedes? Don’t take it for granted. Go through this presentation to find out the exact nature of the issue you are dealing with. Have your vehicle checked by a certified professional if necessary.
What Could Cause The Headlights On Your Porsche 911 To Stop WorkingLancer Service
Discover why your Porsche 911 headlights might flicker out unexpectedly. From aging bulbs to electrical gremlins and moisture mishaps, we're delving into the reasons behind the blackout. Stay tuned to illuminate the road ahead and ensure your lights shine bright for safer journeys.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
What Are The Immediate Steps To Take When The VW Temperature Light Starts Fla...Import Motorworks
Learn how to respond when the red temperature light flashes in your VW with this presentation. From checking coolant levels to seeking professional help, follow these steps promptly to prevent engine damage and ensure safety on the road.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315C EXCAVATOR ANF
Configuration: 315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054E Engine for Caterpillar Built Machines
Media Number -RENR2411-03 Publication Date -01/05/2017 Date Updated -03/05/2017
i02298103
Rocker Shaft - Disassemble
SMCS - 1102-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1855 Retaining Ring Pliers 1
Start By:
a. Remove the rocker shaft assembly. Refer to Disassembly and Assembly, "Rocker Shaft and
Pushrod - Remove".
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1/2
315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP3...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g01150908
1. Remove the retaining ring (1) and remove the washer (2) from both ends of the rocker shaft
assembly.
Note: The rocker shaft (7) is not symmetrical as there is a machined flat (6) toward one end
of the shaft.
2. Place an identification mark on each of the components for installation. Ensure that you
note the component's relationship to the machined flat (6).
3. Remove the rocker arm assembly (3) for the inlet valve from the rocker shaft (7). Remove
the rocker arm assembly (4) for the exhaust valve from the rocker shaft (7).
4. Remove the spring (5) from the rocker shaft assembly.
5. Repeat Step 3 and Step 4 in order to completely disassemble the rocker shaft assembly.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Oct 30 16:04:47 UTC+0800 2020
2/2
315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP3...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315C EXCAVATOR ANF
Configuration: 315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054E Engine for Caterpillar Built Machines
Media Number -RENR2411-03 Publication Date -01/05/2017 Date Updated -03/05/2017
i02298104
Rocker Shaft - Assemble
SMCS - 1102-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1855 Retaining Ring Pliers 1
Illustration 1 g01150908
Typical example
1/2
315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP3...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 1. Clean all of the components and inspect all of the components. Inspect the grooves for the
circlips (1) and ensure that all of the oil holes in the rocker shaft (7) and in the rocker arms
(3 and 4) are not plugged before you begin the assembly procedure. If necessary, replace
any worn components and any damaged components.
2. Check the clearance between the rocker shaft (7) and the bushing of every rocker arm (3 and
4). Refer to the Specifications Manual, "Rocker Shaft" or further information. If necessary,
replace any worn components.
3. Lubricate all of the components with clean engine oil before assembly.
Note: Ensure that the machined flat (6) on the rocker shaft (7) is facing upward.
4. Install a circlip (1) onto the end of the rocker shaft (7) that is closest to the machined flat
(6). Install a washer (2) onto the rocker shaft (7).
5. Install the rocker arm assembly (3) for the inlet valve onto the rocker shaft (7). Install the
rocker arm assembly (4) for the exhaust valve onto the rocker shaft (7).
6. Install the spring (5) onto the rocker shaft (7).
7. Repeat Step 5 and Step 6 in order to assemble the rocker shaft assembly.
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
8. Install the remaining washer (2) and the remaining circlip (1) onto the rocker shaft (7).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Oct 30 16:05:43 UTC+0800 2020
2/2
315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP3...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315C EXCAVATOR ANF
Configuration: 315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054E Engine for Caterpillar Built Machines
Media Number -RENR2411-03 Publication Date -01/05/2017 Date Updated -03/05/2017
i02298106
Rocker Shaft and Pushrod - Install
SMCS - 1102-012; 1208-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6K-0806 Cable Strap 3
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP3...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 1 g00960356
Illustration 2 g00960345
1. Apply clean engine lubricating oil to both ends of the pushrods (6). Install the pushrods (6).
Note: Ensure that the pushrods are installed in the original location and that the pushrods
are seated in the valve lifters correctly.
2. If the rocker shaft was disassembled, install the Tooling (A) around the rocker arms (4) in
order to slightly compress spring (5). The rocker arms must be held away from the
machined face of the cylinder head (2) during reassembly.
3. Loosen the nut (8) and the adjustment screw (7) on each rocker arm. This will help prevent
a bent valve or a bent pushrod during the installation of the rocker shaft.
4. Position the rocker shaft assembly on the cylinder head.
Note: The rocker shaft (3) of the rocker shaft assembly is not symmetrical. The rocker shaft
(3) has a machined flat at the front end of the shaft. Ensure that the machined flat is toward
the top and toward the front end of the engine.
5. Install the Torx screws (1) in the rocker shaft (3).
Note: The longest Torx screw must be installed at the front of the cylinder head in the hole
(X).
6. Ensure that the adjustment screws (7) are properly seated in the ends of the pushrods (6).
7. Alternately tighten the Torx screws (1). Start from the center and work toward the outside.
Tighten the Torx screws (1) to a torque of 35 N·m (26 lb ft).
8. Cut and remove the Tooling (A) from the rocker shaft assembly.
9. Adjust the inlet valve lash to 0.20 mm (0.008 inch) and adjust the exhaust valve lash to
0.45 mm (0.018 inch). Refer to Testing and Adjusting, "Engine Valve Lash -
Inspect/Adjust" for more information on adjusting the valve lash.
End By:
2/3
315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP3...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. a. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Oct 30 16:06:39 UTC+0800 2020
3/3
315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP3...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315C EXCAVATOR ANF
Configuration: 315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054E Engine for Caterpillar Built Machines
Media Number -RENR2411-03 Publication Date -01/05/2017 Date Updated -03/05/2017
i01923525
Cylinder Head - Remove
SMCS - 1100-011
Removal Procedure
Start By:
a. Remove the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold -
Remove and Install".
b. Remove the rocker shaft assembly and the pushrods. Refer to Disassembly and Assembly,
"Rocker Shaft and Pushrod - Remove".
c. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/3
315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP3...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1. Drain the coolant from the engine oil cooler into a suitable container for storage or disposal.
Drain the engine oil from the engine oil cooler into a suitable container. Refer to Operation
and Maintenance Manual for the procedure on draining the engine coolant and the engine
oil.
Note: Refer to Operation and Maintenance Manual, "Refill Capacities" for the coolant
capacity and the engine oil capacity of the engine.
2. Loosen the hose clamp from the upper radiator hose and remove the upper radiator hose
from the water temperature regulator housing.
3. Disconnect the harness assembly from the bus bar for the glow plugs.
Illustration 1 g01001037
4. Disconnect the harness assembly from coolant temperature sensor (2).
5. Remove bolts (3). Remove bypass tube (4) from cylinder head (1). Remove the O-ring seals
from the bypass tube.
2/3
315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP3...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 2 g01000982
6. Gradually loosen cylinder head bolts (5) in reverse numerical order. Refer to Illustration 2.
This will help prevent distortion of the cylinder head.
7. Remove bolts (5) from cylinder head (1).
8. Use a suitable lifting device and carefully lift the cylinder head off the cylinder block. The
weight of the cylinder head is approximately 57 kg (126 lb).
Note: Do not use a lever to separate the cylinder head from the cylinder block.
NOTICE
Place the cylinder head on a surface that will not scratch the face of the
cylinder head.
9. Remove the cylinder head gasket.
Note: Note the location of the dowels on the cylinder block.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Oct 30 16:07:35 UTC+0800 2020
3/3
315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP3...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315C EXCAVATOR ANF
Configuration: 315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054E Engine for Caterpillar Built Machines
Media Number -RENR2411-03 Publication Date -01/05/2017 Date Updated -03/05/2017
i05969946
Cylinder Head - Install
SMCS - 1100-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6238 Guide Bolt 2
B 8T-3052 Degree Wheel 1
C 5P-3975 Rubber Lubricant -
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Thoroughly clean the top of the cylinder block and the bottom of the cylinder head. Ensure
that there is no debris in the cylinder bores.
1/5
315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP3...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 1 g01001065
1. Install the cylinder head gasket on dowels (6) on top of the cylinder block.
Note: Do Not use any sealant or compound on the cylinder head gasket.
2. Install Tooling (A) in the cylinder block.
3. Use a suitable lifting device to install the cylinder head. The weight of the cylinder head is
approximately 57 kg (126 lb).
Note: Ensure that the cylinder head is positioned on dowels (6) .
4. Remove Tooling (A) .
2/5
315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP3...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 2 g00951563
5. Clean the threads of the cylinder head bolts. Inspect the cylinder head bolts.
Note: Do Not use bolts if there is any visual reduction in the diameter of the Threads (Y)
that has not been engaged with the cylinder block. Use a straight edge to check the bolts.
6. Lubricate the threads and the shoulder of the cylinder head bolts with clean engine oil
before installation.
Illustration 3 g03742524
7. Install bolts (5) on cylinder head (1) .
Note: The short bolts are installed in holes that are marked 1, 2, 3, 4, 5, 6, and 9.
Note: The long bolts are installed in holes that are marked 7, 8, and 10.
8. Tighten the cylinder head bolts in numerical order to a torque of 50 N·m (37 lb ft).
9. Tighten the cylinder head bolts in numerical order to a torque of 100 N·m (74 lb ft).
3/5
315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP3...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 4 g00951562
10. Use Tooling (B) to achieve the correct final torque.
Note: If Tooling (B) is not used, place an index mark on each bolt.
11. Tighten the cylinder head bolts in numerical order.
a. Turn the short bolts (2, 5, 6, 7, 8, 9, and 10) for an additional 225 degrees.
b. Turn the long bolts (1, 3, and 4) for an additional 270 degrees.
Illustration 5 g01001037
4/5
315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP3...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. 12. Install new O-ring seals on bypass tube (4) . Apply Tooling (C) to the O-ring seals. Install
the bypass tube in cylinder head (1) . Install bolts (3) .
13. Connect the harness assembly to coolant temperature sensor (2) .
14. Connect the harness assembly to the bus bar for the glow plugs.
15. Install the upper radiator hose to the water temperature regulator housing.
16. Fill the cooling system with coolant. Fill the lubrication system with engine oil.
Note: Refer to Operation and Maintenance Manual, "Refill Capacities" for the cooling
system capacity and the lubrication system capacity of the engine.
End By:
a. Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines -
Remove and Install".
b. Install the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrod - Install".
c. Install the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold -
Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Oct 30 16:08:31 UTC+0800 2020
5/5
315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP3...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315C EXCAVATOR ANF
Configuration: 315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054E Engine for Caterpillar Built Machines
Media Number -RENR2411-03 Publication Date -01/05/2017 Date Updated -03/05/2017
i02333592
Lifter Group - Remove and Install
SMCS - 1209-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7262 Telescoping Magnet 1
Start By:
a. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and
Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP3...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 1 g00540954
1. Use Tooling (A) to remove lifters (1).
Note: Place an identification mark on the lifters for installation purposes.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1U-7262 Telescoping Magnet 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Lubricate the lifters with clean oil before installing the lifters in the cylinder block.
2/3
315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP3...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 2 g00540954
2. Use Tooling (A) to install lifters (1).
Note: Ensure that the lifters are installed in the original location and that the lifters are
seated correctly.
End By:
a. Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Oct 30 16:09:26 UTC+0800 2020
3/3
315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP3...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315C EXCAVATOR ANF
Configuration: 315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054E Engine for Caterpillar Built Machines
Media Number -RENR2411-03 Publication Date -01/05/2017 Date Updated -03/05/2017
i02299051
Camshaft - Remove and Install
SMCS - 1210-010
Removal Procedure
Start By:
a. Remove the rocker shaft assembly and the pushrods. Refer to Disassembly and Assembly,
"Rocker Shaft and Pushrod - Remove".
b. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Turn the engine upside-down so the valve lifters are held in a position away from the
camshaft.
1/3
315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP3...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 1 g00951934
NOTICE
Do not damage the lobes or the bearings when the camshaft is removed
or installed.
2. Carefully remove camshaft (3) from the cylinder block.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Ensure that the camshaft is clean. Lubricate the camshaft with clean engine oil prior
to installation.
NOTICE
Do not damage the lobes or the bearings when the camshaft is removed
or installed.
2/3
315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP3...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. 1. Carefully install camshaft (3) in the cylinder block.
End By:
a. Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Install".
b. Install the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrod - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Oct 30 16:10:22 UTC+0800 2020
3/3
315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP3...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315C EXCAVATOR ANF
Configuration: 315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054E Engine for Caterpillar Built Machines
Media Number -RENR2411-03 Publication Date -01/05/2017 Date Updated -03/05/2017
i02299077
Camshaft Gear - Remove and Install
SMCS - 1210-010-GE
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Name Qty
A 230-6284 Timing Pin (Camshaft) 1
B 230-6283 Timing Pin (Crankshaft) 1
Start By:
a. Remove the fan. Refer to Disassembly and Assembly, "Fan - Remove and Install".
b. Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and
Install".
c. Remove the idler gear. Refer to Disassembly and Assembly, "Idler Gear - Remove and
Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP3...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 1 g01001848
1. Remove the setscrew (1) and the washer from the camshaft gear (2).
2. Remove the camshaft gear from the camshaft.
Note: Do not lose the key from the camshaft gear.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Make sure that the No. 1 cylinder is at the top center compression stroke. Refer to Testing
and Adjusting, "Finding Top Center Position for No. 1 Piston".
2. Inspect the camshaft gear and the key for wear or damage.
3. Install the Tooling (A) through the camshaft gear. Install the Tooling (B) into the crankshaft
web.
2/3
315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP3...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...