1) The document provides step-by-step instructions for disassembling and assembling the final drive of a 315C excavator.
2) Disassembly includes removing 21 components from the final drive housing. Assembly is the reverse of disassembly and requires determining the proper shim thickness to set the rolling torque.
3) Special tools are required and components must be cleaned and lubricated before assembly to ensure proper operation of the reassembled final drive.
Caterpillar Cat 315C L Excavator (Prefix CFB) Service Repair Manual (CFB00001...tuzhiyou2
This document provides instructions for disassembling and assembling the final drive of a 315C excavator. The disassembly process involves removing 21 components from the final drive assembly using various tools. The assembly process describes installing the components in reverse order and determining the proper shim thickness to set the rolling torque. Precise measurements and stake marks are required to ensure correct assembly. Cleanliness is important during assembly to prevent contamination.
This document provides instructions for disassembling and assembling the final drive of a 315C excavator. It begins with removing the final drive assembly from the excavator. Next, it describes removing individual components from the final drive including covers, gears, shafts, seals and housings. The assembly section provides instructions for installing these components in reverse order and includes steps for determining the proper shim thickness to set the rolling torque. The summary is provided in 3 sentences or less.
Caterpillar Cat 315C L Excavator (Prefix CFB) Service Repair Manual (CFB00001...jse7039222
This document provides instructions for disassembling and assembling the final drive of a 315C excavator. The disassembly process involves removing 21 components from the final drive assembly using various tools. The assembly process describes installing the components in reverse order and determining the proper shim thickness to set the rolling torque. Precise measurements and stake marks are required to ensure correct assembly. Cleanliness is important during assembly to prevent contamination.
This document provides instructions for disassembling and assembling the final drive of a 315C excavator. The disassembly process involves removing 21 components from the final drive assembly using various tools. The assembly process describes installing the components in reverse order and determining the proper shim thickness to set the rolling torque. Precise measurements and stake marks are required to ensure correct assembly.
This document provides instructions for disassembling and assembling the final drive of a 315C excavator. It begins with removing the final drive assembly from the excavator. Next it describes removing individual components from the final drive including covers, gears, shafts, seals and housings. The assembly section provides instructions for installing these components in reverse order and includes steps for determining the proper shim thickness to set the rolling torque. The summary is provided in 3 sentences or less.
Caterpillar Cat 315C L Excavator (Prefix CFB) Service Repair Manual (CFB00001...lituo39419496
This document provides instructions for disassembling and assembling the final drive of a 315C excavator. It begins with removing the final drive assembly from the excavator. Next, it describes removing individual components from the final drive including covers, plates, gears, shafts, seals and bearings. The assembly section provides instructions for installing these components in reverse order and includes steps for determining the proper shim thickness to set the rolling torque. The summary is provided in 3 sentences or less.
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It lists 28 steps for disassembly, which include removing bolts, valves, seals, bearings, pistons, and other components. It then lists 25 steps for reassembly in reverse order, noting to clean parts thoroughly, replace all seals and gaskets, and apply a light film of oil before assembling components. Precautions are provided for parts under spring force.
Caterpillar Cat 315C L Excavator (Prefix CFT) Service Repair Manual Instant D...rishang96299
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It lists 28 steps for disassembly, which include removing bolts, valves, seals, bearings, pistons, and other components. It then lists 25 steps for reassembly in reverse order, noting to clean parts thoroughly, replace all seals and gaskets, and apply a light film of oil before assembling components. Precautions are provided for parts under spring force.
Caterpillar Cat 315C L Excavator (Prefix CFB) Service Repair Manual (CFB00001...tuzhiyou2
This document provides instructions for disassembling and assembling the final drive of a 315C excavator. The disassembly process involves removing 21 components from the final drive assembly using various tools. The assembly process describes installing the components in reverse order and determining the proper shim thickness to set the rolling torque. Precise measurements and stake marks are required to ensure correct assembly. Cleanliness is important during assembly to prevent contamination.
This document provides instructions for disassembling and assembling the final drive of a 315C excavator. It begins with removing the final drive assembly from the excavator. Next, it describes removing individual components from the final drive including covers, gears, shafts, seals and housings. The assembly section provides instructions for installing these components in reverse order and includes steps for determining the proper shim thickness to set the rolling torque. The summary is provided in 3 sentences or less.
Caterpillar Cat 315C L Excavator (Prefix CFB) Service Repair Manual (CFB00001...jse7039222
This document provides instructions for disassembling and assembling the final drive of a 315C excavator. The disassembly process involves removing 21 components from the final drive assembly using various tools. The assembly process describes installing the components in reverse order and determining the proper shim thickness to set the rolling torque. Precise measurements and stake marks are required to ensure correct assembly. Cleanliness is important during assembly to prevent contamination.
This document provides instructions for disassembling and assembling the final drive of a 315C excavator. The disassembly process involves removing 21 components from the final drive assembly using various tools. The assembly process describes installing the components in reverse order and determining the proper shim thickness to set the rolling torque. Precise measurements and stake marks are required to ensure correct assembly.
This document provides instructions for disassembling and assembling the final drive of a 315C excavator. It begins with removing the final drive assembly from the excavator. Next it describes removing individual components from the final drive including covers, gears, shafts, seals and housings. The assembly section provides instructions for installing these components in reverse order and includes steps for determining the proper shim thickness to set the rolling torque. The summary is provided in 3 sentences or less.
Caterpillar Cat 315C L Excavator (Prefix CFB) Service Repair Manual (CFB00001...lituo39419496
This document provides instructions for disassembling and assembling the final drive of a 315C excavator. It begins with removing the final drive assembly from the excavator. Next, it describes removing individual components from the final drive including covers, plates, gears, shafts, seals and bearings. The assembly section provides instructions for installing these components in reverse order and includes steps for determining the proper shim thickness to set the rolling torque. The summary is provided in 3 sentences or less.
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It lists 28 steps for disassembly, which include removing bolts, valves, seals, bearings, pistons, and other components. It then lists 25 steps for reassembly in reverse order, noting to clean parts thoroughly, replace all seals and gaskets, and apply a light film of oil before assembling components. Precautions are provided for parts under spring force.
Caterpillar Cat 315C L Excavator (Prefix CFT) Service Repair Manual Instant D...rishang96299
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It lists 28 steps for disassembly, which include removing bolts, valves, seals, bearings, pistons, and other components. It then lists 25 steps for reassembly in reverse order, noting to clean parts thoroughly, replace all seals and gaskets, and apply a light film of oil before assembling components. Precautions are provided for parts under spring force.
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It lists 28 steps for disassembly, which include removing bolts, valves, seals, bearings, pistons, and other components. It then lists 27 steps for reassembly in reverse order, noting to clean parts thoroughly, replace all seals and gaskets, and apply a light film of oil before assembling components. Precautions are provided for parts under spring pressure.
Caterpillar Cat 315C L Excavator (Prefix CFT) Service Repair Manual Instant D...kubei069369925
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It describes 27 steps to disassemble the motor by removing components like bolts, seals, bearings, pistons, springs and plates. It then describes 26 steps for reassembling the motor by installing these components in the reverse order. Precautions are provided to mark parts, clean them, apply lubricants and take care when removing or installing parts with spring forces.
Caterpillar Cat 315C L Excavator (Prefix CFT) Service Repair Manual (CFT00001...fuusejkddmmd3e
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It lists 28 steps for disassembly, which include removing bolts, valves, seals, bearings, pistons, and other components. It then lists 27 steps for reassembly in reverse order, noting to clean parts thoroughly, replace all seals and gaskets, and apply a light film of oil before assembling components. Precautions are provided for parts under spring pressure.
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It lists 28 steps for disassembly, which include removing bolts, valves, seals, bearings, pistons, and other components. It then lists 27 steps for reassembly in reverse order, noting to clean parts thoroughly, replace all seals and gaskets, and apply a light film of oil before assembling components. Precautions are provided for parts under spring pressure.
Caterpillar cat 315 c excavator (prefix cft) service repair manual (cft00001 ...dkdmidkkdk
This document provides instructions for disassembling and assembling the travel motor on 315C and 315C L Excavator models. The disassembly process involves 27 steps to remove components like the traction control valve, travel motor, piston motor, brake pack, pistons, and bearings. The assembly process reverses the disassembly with 23 steps and cautions to clean parts, replace seals and gaskets, apply lubricant, and heat/cool components for proper installation. Proper tooling and following all steps is important to prevent damage during disassembly and assembly.
Caterpillar Cat 315C L Excavator (Prefix CFT) Service Repair Manual (CFT00001...dujkdksmdmdm
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It lists 28 steps for disassembly, which include removing bolts, valves, seals, bearings, pistons, and other components. It then lists 25 steps for reassembly in reverse order, noting to clean parts thoroughly, replace all seals and gaskets, and apply a light film of oil before assembling components. Precautions are provided for parts under spring force.
This document provides instructions for disassembling and assembling the travel motor on 315C and 315C L Excavator models. The disassembly process involves 27 steps to remove components like the traction control valve, travel motor, piston motor, brake pack, pistons, and bearings. The assembly process reverses the disassembly with 23 steps and cautions to clean parts, replace seals and gaskets, apply lubricant, and heat/cool components for proper installation. Proper tooling and following all steps is important to prevent damage during disassembly and assembly.
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It describes 27 steps to disassemble the motor by removing components like bolts, seals, bearings, pistons, springs and plates. It then describes 26 steps for reassembling the motor by installing these components in the reverse order. Precautions are provided to mark parts, clean them, apply lubricants and take care when removing or installing parts with spring forces.
This document provides assembly instructions for a piston pump used in a wheeled excavator model M320F. It consists of 50 steps to assemble the various components of the pump in the correct order. The components include springs, retainers, seals, valves, plates, bushings, shafts, and other parts. Precautions are provided for parts that are spring loaded to prevent injury during assembly.
The document provides instructions for disassembling and assembling the final drive carriers, hubs, and brakes of a M320F wheeled excavator. It lists the required tools and gives step-by-step procedures for removing and installing components such as the carrier housing, planetary gears, brake discs, seals, and bearings. Clearances for the brake discs are also specified to ensure proper functioning.
This document provides assembly instructions for an M318 excavator transmission. It lists required tools and parts, and provides step-by-step instructions to assemble the transmission components, including gears, shafts, seals, bearings, and housing. Proper end play is checked at several steps. Lubricants are specified, and cleanliness during assembly is emphasized.
Caterpillar Cat M315 Excavator (Prefix 7ML) Service Repair Manual (7ML00001-0...orrf0370383
This document provides instructions for removing and installing a swing motor and swing drive on an M315 excavator. It describes releasing hydraulic pressure, draining oil, disconnecting hoses, and removing and installing various components like bolts, seals, and motors. Safety precautions are provided regarding containing fluids, releasing pressure, and preventing personal injury. Detailed step-by-step instructions are given for disassembly and reassembly.
The document provides removal and installation instructions for a precooler, water temperature regulator housing, water pump, and other engine components. It includes notices about containing fluids, keeping parts clean, and lists required tools. The step-by-step instructions describe disconnecting hoses and electrical connections, removing mounting bolts and components, and installing parts in reverse order while applying sealant compounds as needed. Illustrations show the component locations and part numbers.
This document provides instructions for installing and removing components of the front gear group of a C18 industrial engine. It describes:
1. Cleaning and inspecting components before installation and removing components in reverse order of installation.
2. Installing the front plate and gears, including adjusting backlash between gears.
3. Lubricating and torquing fasteners to specified values.
This document provides instructions for removing and installing a flywheel housing on a C18 Industrial Engine WJB. It is a 3-page service manual excerpt that describes:
1) Required tools and safety notices
2) Removal procedure which includes supporting the engine, removing bolts and lifting the housing off
3) Installation procedure which includes cleaning, applying sealant, positioning the housing and tightening bolts in a specific sequence and torque.
The document provides instructions for installing an engine oil filter base which includes:
1. Lubricating the O-rings and installing them on the engine oil filter base.
2. Positioning the engine oil filter base and installing bolts to secure it.
3. Reconnecting any disconnected tubes.
The instructions are intended for technicians and include safety warnings for containing fluids and wearing protective equipment when working with pressurized parts.
1) The document provides disassembly and assembly instructions for removing and installing various components of a C18 industrial engine, including the power take-off drive group, vibration damper and pulley, crankshaft front seal, and front cover.
2) The instructions include lists of required tools and detailed step-by-step procedures with accompanying illustrations.
3) Special notes are provided regarding keeping parts clean, inspecting components, and not using lubricants during certain installation procedures.
The document provides instructions for removing and installing various fuel system components on a C18 Industrial Engine, including:
- Removing and installing the fuel priming pump.
- Removing the fuel filter base and disassembling/assembling its components.
- Removing and installing the fuel transfer pump.
- Removing the electronic unit injectors.
The summaries provide concise overviews of the removal and installation procedures for each component in 3 sentences or less.
This document provides instructions for removing and installing various fuel system components on a Caterpillar C18 Industrial Engine, including:
1) Removing and installing the fuel priming pump, fuel filter base, fuel transfer pump, and electronic unit injectors.
2) Disassembling and assembling the fuel filter base to replace seals and fittings.
3) Procedures include disconnecting fuel lines and electrical connections, marking parts for reinstallation, and applying thread lock compounds. Safety notices advise containing fluids and preventing contamination.
This service repair manual provides instructions for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, and the engine oil filter base on a Caterpillar C11 industrial engine. The procedures describe using various tools to remove and install components in a specific sequence, and include notices about keeping parts clean and containing fluids.
This document provides instructions for removing and installing various engine components on a Caterpillar C11 Industrial Engine. It describes procedures for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, the engine oil filter base, and the engine oil cooler. The document contains illustrations and lists required tools for each procedure.
This document provides instructions for removing and installing a unit injector, unit injector sleeve, and turbocharger from a C9.3 Industrial Engine. The unit injector removal procedure involves disconnecting electrical and fuel lines, loosening mounting bolts, and extracting the injector. Installation requires cleaning, lubricating seals, and tightening bolts. The sleeve procedure includes draining coolant, cutting threads to remove the old sleeve, cleaning the bore, applying retaining compound to the new sleeve, and installing with a hammer and driver. The turbocharger removal involves disconnecting coolant and air lines and removing mounting nuts. Installation requires applying anti-seize to bolts and tightening clamps and nuts.
More Related Content
Similar to Caterpillar Cat 315C Excavator (Prefix CFB) Service Repair Manual (CFB00001 and up).pdf
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It lists 28 steps for disassembly, which include removing bolts, valves, seals, bearings, pistons, and other components. It then lists 27 steps for reassembly in reverse order, noting to clean parts thoroughly, replace all seals and gaskets, and apply a light film of oil before assembling components. Precautions are provided for parts under spring pressure.
Caterpillar Cat 315C L Excavator (Prefix CFT) Service Repair Manual Instant D...kubei069369925
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It describes 27 steps to disassemble the motor by removing components like bolts, seals, bearings, pistons, springs and plates. It then describes 26 steps for reassembling the motor by installing these components in the reverse order. Precautions are provided to mark parts, clean them, apply lubricants and take care when removing or installing parts with spring forces.
Caterpillar Cat 315C L Excavator (Prefix CFT) Service Repair Manual (CFT00001...fuusejkddmmd3e
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It lists 28 steps for disassembly, which include removing bolts, valves, seals, bearings, pistons, and other components. It then lists 27 steps for reassembly in reverse order, noting to clean parts thoroughly, replace all seals and gaskets, and apply a light film of oil before assembling components. Precautions are provided for parts under spring pressure.
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It lists 28 steps for disassembly, which include removing bolts, valves, seals, bearings, pistons, and other components. It then lists 27 steps for reassembly in reverse order, noting to clean parts thoroughly, replace all seals and gaskets, and apply a light film of oil before assembling components. Precautions are provided for parts under spring pressure.
Caterpillar cat 315 c excavator (prefix cft) service repair manual (cft00001 ...dkdmidkkdk
This document provides instructions for disassembling and assembling the travel motor on 315C and 315C L Excavator models. The disassembly process involves 27 steps to remove components like the traction control valve, travel motor, piston motor, brake pack, pistons, and bearings. The assembly process reverses the disassembly with 23 steps and cautions to clean parts, replace seals and gaskets, apply lubricant, and heat/cool components for proper installation. Proper tooling and following all steps is important to prevent damage during disassembly and assembly.
Caterpillar Cat 315C L Excavator (Prefix CFT) Service Repair Manual (CFT00001...dujkdksmdmdm
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It lists 28 steps for disassembly, which include removing bolts, valves, seals, bearings, pistons, and other components. It then lists 25 steps for reassembly in reverse order, noting to clean parts thoroughly, replace all seals and gaskets, and apply a light film of oil before assembling components. Precautions are provided for parts under spring force.
This document provides instructions for disassembling and assembling the travel motor on 315C and 315C L Excavator models. The disassembly process involves 27 steps to remove components like the traction control valve, travel motor, piston motor, brake pack, pistons, and bearings. The assembly process reverses the disassembly with 23 steps and cautions to clean parts, replace seals and gaskets, apply lubricant, and heat/cool components for proper installation. Proper tooling and following all steps is important to prevent damage during disassembly and assembly.
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It describes 27 steps to disassemble the motor by removing components like bolts, seals, bearings, pistons, springs and plates. It then describes 26 steps for reassembling the motor by installing these components in the reverse order. Precautions are provided to mark parts, clean them, apply lubricants and take care when removing or installing parts with spring forces.
Similar to Caterpillar Cat 315C Excavator (Prefix CFB) Service Repair Manual (CFB00001 and up).pdf (8)
This document provides assembly instructions for a piston pump used in a wheeled excavator model M320F. It consists of 50 steps to assemble the various components of the pump in the correct order. The components include springs, retainers, seals, valves, plates, bushings, shafts, and other parts. Precautions are provided for parts that are spring loaded to prevent injury during assembly.
The document provides instructions for disassembling and assembling the final drive carriers, hubs, and brakes of a M320F wheeled excavator. It lists the required tools and gives step-by-step procedures for removing and installing components such as the carrier housing, planetary gears, brake discs, seals, and bearings. Clearances for the brake discs are also specified to ensure proper functioning.
This document provides assembly instructions for an M318 excavator transmission. It lists required tools and parts, and provides step-by-step instructions to assemble the transmission components, including gears, shafts, seals, bearings, and housing. Proper end play is checked at several steps. Lubricants are specified, and cleanliness during assembly is emphasized.
Caterpillar Cat M315 Excavator (Prefix 7ML) Service Repair Manual (7ML00001-0...orrf0370383
This document provides instructions for removing and installing a swing motor and swing drive on an M315 excavator. It describes releasing hydraulic pressure, draining oil, disconnecting hoses, and removing and installing various components like bolts, seals, and motors. Safety precautions are provided regarding containing fluids, releasing pressure, and preventing personal injury. Detailed step-by-step instructions are given for disassembly and reassembly.
The document provides removal and installation instructions for a precooler, water temperature regulator housing, water pump, and other engine components. It includes notices about containing fluids, keeping parts clean, and lists required tools. The step-by-step instructions describe disconnecting hoses and electrical connections, removing mounting bolts and components, and installing parts in reverse order while applying sealant compounds as needed. Illustrations show the component locations and part numbers.
This document provides instructions for installing and removing components of the front gear group of a C18 industrial engine. It describes:
1. Cleaning and inspecting components before installation and removing components in reverse order of installation.
2. Installing the front plate and gears, including adjusting backlash between gears.
3. Lubricating and torquing fasteners to specified values.
This document provides instructions for removing and installing a flywheel housing on a C18 Industrial Engine WJB. It is a 3-page service manual excerpt that describes:
1) Required tools and safety notices
2) Removal procedure which includes supporting the engine, removing bolts and lifting the housing off
3) Installation procedure which includes cleaning, applying sealant, positioning the housing and tightening bolts in a specific sequence and torque.
The document provides instructions for installing an engine oil filter base which includes:
1. Lubricating the O-rings and installing them on the engine oil filter base.
2. Positioning the engine oil filter base and installing bolts to secure it.
3. Reconnecting any disconnected tubes.
The instructions are intended for technicians and include safety warnings for containing fluids and wearing protective equipment when working with pressurized parts.
1) The document provides disassembly and assembly instructions for removing and installing various components of a C18 industrial engine, including the power take-off drive group, vibration damper and pulley, crankshaft front seal, and front cover.
2) The instructions include lists of required tools and detailed step-by-step procedures with accompanying illustrations.
3) Special notes are provided regarding keeping parts clean, inspecting components, and not using lubricants during certain installation procedures.
The document provides instructions for removing and installing various fuel system components on a C18 Industrial Engine, including:
- Removing and installing the fuel priming pump.
- Removing the fuel filter base and disassembling/assembling its components.
- Removing and installing the fuel transfer pump.
- Removing the electronic unit injectors.
The summaries provide concise overviews of the removal and installation procedures for each component in 3 sentences or less.
This document provides instructions for removing and installing various fuel system components on a Caterpillar C18 Industrial Engine, including:
1) Removing and installing the fuel priming pump, fuel filter base, fuel transfer pump, and electronic unit injectors.
2) Disassembling and assembling the fuel filter base to replace seals and fittings.
3) Procedures include disconnecting fuel lines and electrical connections, marking parts for reinstallation, and applying thread lock compounds. Safety notices advise containing fluids and preventing contamination.
This service repair manual provides instructions for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, and the engine oil filter base on a Caterpillar C11 industrial engine. The procedures describe using various tools to remove and install components in a specific sequence, and include notices about keeping parts clean and containing fluids.
This document provides instructions for removing and installing various engine components on a Caterpillar C11 Industrial Engine. It describes procedures for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, the engine oil filter base, and the engine oil cooler. The document contains illustrations and lists required tools for each procedure.
This document provides instructions for removing and installing a unit injector, unit injector sleeve, and turbocharger from a C9.3 Industrial Engine. The unit injector removal procedure involves disconnecting electrical and fuel lines, loosening mounting bolts, and extracting the injector. Installation requires cleaning, lubricating seals, and tightening bolts. The sleeve procedure includes draining coolant, cutting threads to remove the old sleeve, cleaning the bore, applying retaining compound to the new sleeve, and installing with a hammer and driver. The turbocharger removal involves disconnecting coolant and air lines and removing mounting nuts. Installation requires applying anti-seize to bolts and tightening clamps and nuts.
This document provides instructions for disassembling and assembling the freewheel stator component of a torque converter. The disassembly process involves using various tools to remove over 30 individual parts in a specific sequence. Cleanliness is emphasized. The assembly process reverses the disassembly steps and provides additional details like proper orientation and torque specifications for reinstalling components.
This document provides instructions for disassembling and assembling the torque converter of a 966H wheel loader. It begins with required tools and safety notices. The disassembly instructions describe removing over 30 individual parts in multiple steps, including the torque converter housing, impeller, stator, carrier shaft, and turbine. The assembly section then lists the components and provides the reverse steps for reassembling the torque converter. Cleanliness is emphasized as important during disassembly and assembly.
This document provides instructions for removing and installing the rear gear group and flywheel on a Caterpillar C11 engine. The removal procedure involves using various tools to remove 12 different components in 11 steps. The installation procedure involves 14 steps of reinstalling components and includes notes about matching dimensions and applying threadlock. Tools, torque specifications, and cautions are provided.
This document provides instructions for disassembling and assembling the piston pump of the steering system on a Caterpillar 962K wheel loader. The disassembly procedure outlines 28 steps to remove components like bolts, valves, spools, springs, and bearings. The assembly procedure describes 34 steps and cautions to install these components in reverse order and ensure proper spring tension, seals, and shaft clearance. Precautions are included to prevent injury from released spring forces.
This document provides instructions for assembling and disassembling parts of a 962K wheel loader. It includes 37 steps to assemble a piston pump, with diagrams showing each step. It also provides procedures for removing and installing a main control valve and electrohydraulic control components, with warnings about releasing pressure before servicing hydraulic systems.
The document provides instructions for removing and installing a secondary steering pump and electric motor on a Caterpillar 962K wheel loader. It outlines 28 steps for disassembly of the pump which includes removing valves, spools, plugs, springs, and other internal components. The assembly section details 34 steps for reinstalling these parts in the reverse order and adjusting axial shaft end play.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315C EXCAVATOR CFB
Configuration: 315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Engine
Disassembly and Assembly
315C Excavator Machine Systems
Media Number -RENR5525-05 Publication Date -01/11/2008 Date Updated -10/11/2008
i01960779
Final Drive - Disassemble
SMCS - 4050-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Repair Stand 1
B 1U-7600 Slide Hammer 1
C 138-7575 Link Brackets 3
D 154-6181 Forcing Screw 2
Start By:
A. Remove the final drive. Refer to Disassembly and Assembly, "Final Drive- Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
1/10
315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Dispose of all fluids according to local regulations and mandates.
NOTICE
Failure to properly assemble parts or failure to follow established
procedures can lead to damage of the parts and assembly.
To avoid damage to parts, always identify and mark the parts so that
they can be installed in the same location. Ensure that gear surfaces
align. Never force parts during assembly.
Illustration 1 g00777501
1. Install the final drive assembly on Tooling (A) .
Illustration 2 g01018685
2/10
315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 2. Remove bolts (1). Remove plugs (2) and the O-ring seals from cover (3). Remove cover
(3) .
Illustration 3 g00777515
3. Use Tooling (B) in order to remove plate (4) .
Illustration 4 g00777542
4. Remove carrier assembly (5) from the main housing. The weight of the carrier assembly is
approximately16 kg (35 lb).
3/10
315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 5 g00777548
5. Remove spacer (6) .
Illustration 6 g00777570
6. Use a suitable punch and a hammer to install spring pin (7) into planetary shaft (8) .
Illustration 7 g01021689
4/10
315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 7. Remove planetary shaft (8). Remove spring pin (7). Remove thrust washers (9). Remove
planetary gear (11) and bearing (10) .
8. Repeat Steps 6 and 7 in order to remove the other two planetary gears from the carrier.
Illustration 8 g00777624
9. Remove gear (12) .
Illustration 9 g00777626
10. Remove gear (13). Remove spacer (14) .
5/10
315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 10 g00777631
11. Use Tooling (C) and a suitable lifting device in order to remove carrier assembly (15). The
weight of carrier assembly (15) is approximately 30 kg (65 lb).
Illustration 11 g01021690
12. Use a suitable punch and a hammer to install spring pin (16) into planetary shaft (17) .
Illustration 12 g01021692
6/10
315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. 13. Remove spring pin (16) from planetary shaft (17). Remove thrust washers (18), bearings
(19) and gear (20) from the carrier assembly.
Illustration 13 g01018688
14. Remove bolts (21) .
Illustration 14 g00778413
15. Use Tooling (D) in order to push gear (22) from the upper housing.
7/10
315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 15 g00778461
16. Remove gear (22). Four dowel pins (23) will stay with the gear.
Illustration 16 g00778471
17. Use a suitable press in order to remove dowel pins (23) .
Illustration 17 g01018689
18. Remove shim (24) and washer (25) .
8/10
315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 18 g01018690
19. Separate housing (26) from housing (27) .
Illustration 19 g01018692
20. Remove Duo-cone seal gp (28) from housing (27) .
9/10
315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 20 g01018693
21. Remove Duo-cone seal gp (29) and bearings (30) from housing (26) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Nov 2 23:26:14 UTC+0800 2020
10/10
315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Eng...
2020/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315C EXCAVATOR CFB
Configuration: 315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Engine
Disassembly and Assembly
315C Excavator Machine Systems
Media Number -RENR5525-05 Publication Date -01/11/2008 Date Updated -10/11/2008
i01961218
Final Drive - Assemble
SMCS - 4050-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Repair Stand 1
C 138-7575 Link Brackets 3
D 126-3994 Seal Installer 1
E
1U-9895 Crossblock 1
5F-7369 Leg 2
5P-4808 Cap 2
3H-0465 Plate 4
1B-4207 Nut 2
F 6V-2012 Depth Micrometer 1
G 169-0503 Installation Kit 1
Note: Replace all O-ring seals and gaskets. Apply a light film of"10W" oil to all components
before assembly.
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
1/12
315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 1 g01021697
1. Place housing (27) on Tooling (A) .
2. Use Tooling (G) in order to clean the Duo-cone seal gp prior to installation. Use Tooling
(D) in order to install Duo-cone seal gp (28) into housing (27) .
Illustration 2 g01018693
3. Install bearings (30) into housing (26). Use Tooling (D) in order to install Duo-cone seal gp
(29) into housing (26).
2/12
315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 3 g01018690
4. Install Tooling (C) to housing (26). Use Tooling (C) and a suitable lifting device in order to
install housing (26) onto housing (27) .
Illustration 4 g01018688
5. Install gear (22). Install bolts (21) in order to hold the two housings together. This is
necessary in order to transport the housings to the press.
Note: The following steps are necessary in order to determine the proper shim or shims
needed to set the rolling torque.
3/12
315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 5 g01018688
a. Set the main housing assembly in a suitable press. Remove bolts (21). Remove gear
(22) .
Illustration 6 g01021714
b. Install Tooling (E). Use a suitable press in order to apply the load of 4000 kg (8818
lb). Rotate the housing in order to seat bearings (30). Reduce the load to 1000 ± 100
kg (2204 ± 220 lb).
4/12
315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 7 g01018888
c. Maintain the load pressure of 1000 ± 100 kg (2204 ± 220 lb). Use Tool (F) in order to
obtain Measurement (A). Record the measurement.
Illustration 8 g00781842
d. Use Tooling (F) in order to obtain Measurement (B) on gear (22). Record the
measurement.
5/12
315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 9 g00781847
Illustration 10 g01018689
e. Measure the thickness of washer (25). Record the measurement.
f. Install washer (25). Install the required shims. The shim thickness is determined by
subtracting Dimension (A) from Dimension (B) and subtractingDimension (C). This
thickness has a tolerance of ± 0.050 mm ( ± 0.0020 inch). If two shims are required,
install the thinner shim next to gear (22) .
6/12
315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 11 g00782429
6. Install gear (22) and pins (23). Install bolts (21). Tighten bolts (21) to a torque of 270 ± 40
N·m (199 ± 30 lb ft).
Illustration 12 g01021692
7. Install bearings (19) and gear (20). Install thrust washers (18). Install planetary shaft (17)
and spring pin (16) .
Illustration 13 g01021690
7/12
315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 8. Use a suitable punch and a hammer in order to drive spring pin (16) into planetary shaft
(17) .
Illustration 14 g00782239
Stake marks on each side of spring pin (16)
(D) Measurement of 1.5 mm (0.06 inch) from outside diameter
9. Use a suitable punch in order to peen planetary shaft (17) on each side of spring pin (16).
Each stake mark should be approximately 1.5 mm (0.06 inch) from the outside diameter of
the spring pin.
10. Repeat Steps 7 through 9 in order to install the other two planetary gears into the carrier.
Illustration 15 g00777631
8/12
315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. 11. Use Tooling (C) and a suitable lifting device in order to install carrier assembly (15). The
weight of carrier assembly (15) is approximately 30 kg (65 lb).
Illustration 16 g00777626
12. Install spacer (14). Install gear (13).
Illustration 17 g00777624
13. Install gear (12) .
9/12
315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 18 g01021689
14. Install planetary gear (11) and bearing (10). Install thrust washers (9). Install planetary shaft
(8). Install spring pin (7) .
Illustration 19 g00782239
Stake marks on each side of spring pin (7)
(D) Measurement of 1.5 mm (0.06 inch) from outside diameter
15. Use a suitable punch in order to peen shaft (8) on each side of spring pin (7). Each stake
mark should be approximately 1.5 mm (0.06 inch) from the outside diameter of the spring
pin.
16. Repeat Steps 14 and 17 in order to install the other two planetary gears into the carrier.
10/12
315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Eng...
2020/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 20 g00777548
17. Install spacer (6) .
Illustration 21 g00777542
18. Install carrier assembly (5) into the main housing. The weight of carrier assembly (5) is
approximately 16 kg (35 lb).
Illustration 22 g00782448
11/12
315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Eng...
2020/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. 19. Install plate (4) .
Illustration 23 g01018685
20. Install cover (3). Install bolts (1). Tighten bolts (1) to a torque of 105 ± 20 N·m (77 ± 15 lb
ft). Install plugs (2) and the O-ring seals. Tighten plugs (2) to a torque of 80 ± 10 N·m (59 ±
7 lb ft).
End By: Install the final drive. Refer to Disassembly and Assembly, "Final Drive - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Nov 2 23:27:10 UTC+0800 2020
12/12
315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Eng...
2020/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315C EXCAVATOR CFB
Configuration: 315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Engine
Disassembly and Assembly
315C Excavator Machine Systems
Media Number -RENR5525-05 Publication Date -01/11/2008 Date Updated -10/11/2008
i01961382
Final Drive - Install
SMCS - 4050-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
C 9S-3263 Thread Lock Compound 1
1. Make sure that the mating surfaces of the final drive and the undercarriage frame are
thoroughly clean and free of dirt and debris prior to assembly.
2. Check the condition of the O-ring seals that are used in the ends of the tube assemblies.
Check the condition of the O-ring seals that are used in the ends of the hose assemblies. If
the O-ring seals are worn or damaged, use new parts for replacement.
1/4
315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 1 g00486987
3. Fasten Tooling (A) and a suitable lifting device to final drive (7). Carefully, put the final
drive in position on the undercarriage frame.
Illustration 2 g00486988
4. Apply Tooling (C) on the threads of bolts (8). Install bolts (8) that hold the final drive to the
undercarriage frame. Tighten bolts (8) evenly.
5. Install plugs (9) in the forcing bolt holes.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
2/4
315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...