This document provides instructions for removing and installing a flywheel housing on a C18 Industrial Engine WJB. It is a 3-page service manual excerpt that describes:
1) Required tools and safety notices
2) Removal procedure which includes supporting the engine, removing bolts and lifting the housing off
3) Installation procedure which includes cleaning, applying sealant, positioning the housing and tightening bolts in a specific sequence and torque.
What Could Cause The Headlights On Your Porsche 911 To Stop WorkingLancer Service
Discover why your Porsche 911 headlights might flicker out unexpectedly. From aging bulbs to electrical gremlins and moisture mishaps, we're delving into the reasons behind the blackout. Stay tuned to illuminate the road ahead and ensure your lights shine bright for safer journeys.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
What Are The Immediate Steps To Take When The VW Temperature Light Starts Fla...Import Motorworks
Learn how to respond when the red temperature light flashes in your VW with this presentation. From checking coolant levels to seeking professional help, follow these steps promptly to prevent engine damage and ensure safety on the road.
2. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C18 INDUSTRIAL ENGINE WJB
Configuration: C18 Industrial Engine WJB00001-UP
Disassembly and Assembly
C18 Fire Pump Industrial Engine
Media Number -KENR8146-02 Publication Date -01/10/2014 Date Updated -17/10/2014
i07535626
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 439-3939 Link Bracket 2
B -
Block
12 by 12 by 24
1
Start By:
a. Remove the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear
Seal - Remove".
b. Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starter
Motor - Remove and Install".
c. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
d. Remove the engine speed sensor. Refer to Disassembly and Assembly, "Engine Speed
Sensor - Remove and Install".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/6(W)
w
2020/6/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, PERJ1017, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01238988
1. Use Tooling (B) or a suitable block to support the rear of the cylinder block in order to
remove flywheel housing (1). The weight of the engine is approximately 1814 kg (4000 lb).
2/6(W)
w
2020/6/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. Illustration 2 g01239002
2. Install Tooling (A) and a suitable lifting device on flywheel housing (1). The weight of
flywheel housing (1) is approximately 105 kg (230 lb).
3. Remove bolts (2). Remove flywheel housing (1) from the cylinder block.
4. Remove gasket (3) from flywheel housing (1).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 439-3939 Link Bracket 2
C - Loctite Superflex Silicone Adhesive Sealant, Blue -
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
3/6(W)
w
2020/6/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Illustration 3 g01239002
1. Thoroughly clean flywheel housing (1) and the rear face of the cylinder block.
2. Install Tooling (A) and a suitable lifting device on flywheel housing (1). The weight of
flywheel housing (1) is approximately 105 kg (230 lb).
3. Install gasket (3) on the dowel pins of the cylinder block. Apply Tooling (C) to the bottom
of gasket (3) in order to fill the space at the cylinder block, flywheel housing (1), and the
engine oil pan.
4. Position flywheel housing (1) and install bolts (2).
4/6(W)
w
2020/6/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Illustration 4 g00551652
5. Tighten the bolts, as follows:
a. In a numerical sequence, tighten Bolt (1) through Bolt (24) to a torque of
40 ± 10 N·m (30 ± 7 lb ft).
b. In a numerical sequence, again tighten Bolt (1) through Bolt (9) to a torque of
135 ± 20 N·m (100 ± 15 lb ft).
c. In a numerical sequence, again tighten Bolt (10) through Bolt (24) to a torque of
55 ± 10 N·m (40 ± 7 lb ft).
6. Remove Tooling (A).
End By:
a. Install the engine speed sensor. Refer to Disassembly and Assembly, "Engine Speed Sensor
- Remove and Install".
b. Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
c. Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install".
d. Install the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal -
Install".
5/6(W)
w
2020/6/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C18 INDUSTRIAL ENGINE WJB
Configuration: C18 Industrial Engine WJB00001-UP
Disassembly and Assembly
C18 Fire Pump Industrial Engine
Media Number -KENR8146-02 Publication Date -01/10/2014 Date Updated -17/10/2014
i03303545
Vibration Damper and Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Stud
(5/8 - 18 x 9 inch)
2
Start By:
A. Remove the alternator drive belt. Refer to Disassembly and Assembly, "Alternator -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4(W)
w
2020/6/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Illustration 1 g01686873
1. Remove two bolts (3) and install Tooling (A) .
2. Remove remaining bolts (3). Remove pulley (1) from vibration damper assembly (2) .
3. Use two people in order to remove vibration damper assembly (2). The weight of vibration
damper assembly (2) is approximately 46 kg (100 lb).
Illustration 2 g01691875
4. Remove bolts (7) and remove spacer (6) .
5. separate damper (5) from adapter (4) .
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A -
Guide Stud
(5/8 - 18 x 9 inch)
2
2/4(W)
w
2020/6/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. B 4C-5593 Anti-Seize Compound -
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Thoroughly inspect the viscous damper for signs of leakage or for signs
of a dented (damaged) case. Either of these conditions can cause the
weight to make contact with the case. This can affect the viscous
damper's operation.
Illustration 3 g01691875
1. Position damper (5) on adapter (4) .
2. Position spacer (6) and install bolts (7) .
3/4(W)
w
2020/6/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Illustration 4 g01686873
3. Install Tooling (A) in the crankshaft.
4. Install vibration damper assembly (2) on Tooling (A) .
5. Install pulley (1) on Tooling (A) .
6. Apply Tooling (B) to bolts (3) .
7. Remove Tooling (A) and install the remaining bolts.
End By: Install the alternator drive belt. Refer to Disassembly and Assembly, "Alternator -
Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jun 14 08:45:40 UTC+0800 2020
4/4(W)
w
2020/6/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C18 INDUSTRIAL ENGINE WJB
Configuration: C18 Industrial Engine WJB00001-UP
Disassembly and Assembly
C18 Fire Pump Industrial Engine
Media Number -KENR8146-02 Publication Date -01/10/2014 Date Updated -17/10/2014
i03190521
Crankshaft Front Seal - Remove
SMCS - 1160-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
B - Pry Bar 1
C 5P-7318 Wear Sleeve Distorter Group 1
Start By:
a. Remove the vibration damper and the pulley. Refer to Disassembly and Assembly,
"Vibration Damper and Pulley - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: The crankshaft front seal and the wear sleeve must be replaced at the same time. Once the
crankshaft front seal and the wear sleeve are separated, these components can not be used again.
1/2(W)
w
2020/6/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Illustration 1 g01044861
Note: Ensure that you do not damage the front housing with Tooling (B).
Note: If the wear sleeve starts to slide off the crankshaft, go to Step 2.
1. Use Tooling (B) to pry around the lip of wear sleeve (2).
2. Use a small drill in order to puncture three or more holes in crankshaft front seal (1).
3. Use Tooling (A) to remove crankshaft front seal (1).
4. If necessary, use Tooling (C) to remove wear sleeve (2).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jun 14 08:46:36 UTC+0800 2020
2/2(W)
w
2020/6/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C18 INDUSTRIAL ENGINE WJB
Configuration: C18 Industrial Engine WJB00001-UP
Disassembly and Assembly
C18 Fire Pump Industrial Engine
Media Number -KENR8146-02 Publication Date -01/10/2014 Date Updated -17/10/2014
i03203845
Crankshaft Front Seal - Install
SMCS - 1160-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
D 5P-1733 Seal Locator 1
E 5P-1737 Bolt 3
F 9S-8858 Nut (Seal Installer) 1
G 6V-6142 Seal Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: The crankshaft front seal and the wear sleeve must be replaced at the same time. Once the
crankshaft front seal and the wear sleeve are separated, these components cannot be used again.
Note: Do not use any type of lubricant during the installation of the crankshaft front seal
and the wear sleeve.
1. Before installation of the crankshaft front seal and the wear sleeve, inspect the crankshaft
for scratches. Also, inspect the crankshaft for any distortion on the surface that may lead to
1/3(W)
w
2020/6/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. an out of round condition. Use a polishing cloth in order to remove any imperfections on the
crankshaft.
2. Clean the outside diameter of the crankshaft.
Illustration 1 g01635200
3. Fasten Tooling (D) to the crankshaft with Tooling (E).
Note: Install the crankshaft front seal with the arrow that shows the direction of crankshaft
rotation toward the front of the engine.
4. Position wear sleeve (2) and crankshaft front seal (1) on Tooling (D). Install Tooling (G) on
Tooling (D). Lubricate the face of the washer on Tooling (F). Install Tooling (F) on Tooling
(D).
5. Tighten Tooling (F) until Tooling (G) contacts Tooling (D).
6. Remove Tooling (F) and Tooling (G) from Tooling (D).
7. Remove Tooling (E) and Tooling (D) from the crankshaft.
End By:
a. Install the vibration damper and the pulley. Refer to Disassembly and Assembly, "Vibration
Damper and Pulley - Remove and Install".
2/3(W)
w
2020/6/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C18 INDUSTRIAL ENGINE WJB
Configuration: C18 Industrial Engine WJB00001-UP
Disassembly and Assembly
C18 Fire Pump Industrial Engine
Media Number -KENR8146-02 Publication Date -01/10/2014 Date Updated -17/10/2014
i04275771
Front Cover - Remove
SMCS - 1166-011
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01100930
1/2(W)
w
2020/6/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. 1. Remove button head screws (3).
2. Remove nuts (7) and washers (6) from studs (4).
3. Remove front cover (2) from front housing (1).
4. Remove O-ring seal (5) from studs (4).
5. Remove seal (8) from front cover (2).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jun 14 08:48:27 UTC+0800 2020
2/2(W)
w
2020/6/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C18 INDUSTRIAL ENGINE WJB
Configuration: C18 Industrial Engine WJB00001-UP
Disassembly and Assembly
C18 Fire Pump Industrial Engine
Media Number -KENR8146-02 Publication Date -01/10/2014 Date Updated -17/10/2014
i04275789
Front Cover - Install
SMCS - 1166-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 155-0695 Thread Lock Compound -
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2(W)
w
2020/6/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Illustration 1 g01268777
1. If studs (4) are loose or the threads are damaged, install new studs in front housing (1).
Apply Tooling (A) to the threads of the studs. Install the studs in the front housing. Install O
-ring seal (5) on the studs.
2. Install seal (8) in front cover (2).
3. Install front cover (2) on studs (4). Install washers (6) and nuts (7).
4. Install button head screws (3). Tighten the button head screws to a torque of 21 ± 3 N·m
(15 ± 2 lb ft).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jun 14 08:49:23 UTC+0800 2020
2/2(W)
w
2020/6/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C18 INDUSTRIAL ENGINE WJB
Configuration: C18 Industrial Engine WJB00001-UP
Disassembly and Assembly
C18 Fire Pump Industrial Engine
Media Number -KENR8146-02 Publication Date -01/10/2014 Date Updated -17/10/2014
i02721549
Gear Group (Front) - Remove
SMCS - 1206-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
Start By:
a. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
b. Remove the air compressor, if necessary. Refer to Disassembly and Assembly, "Air
Compressor - Remove and Install".
c. Remove the water pump, if necessary. Refer to Disassembly and Assembly, "Water Pump -
Remove".
d. Remove the auxiliary water pump, if necessary. Refer to Disassembly and Assembly,
"Auxiliary Water Pump - Remove".
e. Remove the fuel transfer pump, if necessary. Refer to Disassembly and Assembly, "Fuel
Transfer Pump - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/8(W)
w
2020/6/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. NOTICE
Do not turn the crankshaft or the camshaft while the camshaft gear is
removed. If the front gear group is not correctly timed during
installation, interference can occur between the pistons and the valves,
resulting in damage to the engine.
Note: Be sure to mark the orientation of each of the gears for installation purposes.
Illustration 1 g01008429
1. Remove bolts (2) and thrust plate (1).
2/8(W)
w
2020/6/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Illustration 2 g01008430
2. Remove sealing plate (3) and adapter (4).
Illustration 3 g01008431
3. Remove O-ring seal (5) and O-ring seal (6) from sealing plate (3).
3/8(W)
w
2020/6/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Illustration 4 g01101536
4. Remove bolts (8), plate (9), and adjustable idler gear assembly (7).
5. Use Tooling (A) and remove the sleeve bearing from adjustable idler gear assembly (7).
4/8(W)
w
2020/6/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. Illustration 5 g01101045
6. Remove bolts (11), plate (12), and idler gear assembly (10).
7. Use Tooling (A) and remove the sleeve bearing from idler gear assembly (10).
5/8(W)
w
2020/6/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. Illustration 6 g01101048
8. Remove bolts (14), plate (15), and cluster gear assembly (13).
9. Use Tooling (A) and remove the sleeve bearing from cluster gear assembly (13).
6/8(W)
w
2020/6/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
26. Illustration 7 g01101050
Note: Stub shaft assembly (16) must be removed in order to remove plate (22). The
backlash for the camshaft gear and the adjustable idler gear assembly will need to be
readjusted at assembly.
10. Remove nuts (17) and remove stub shaft assembly (16).
Note: Stub shaft (18) must be removed in order to remove plate (22).
11. Remove nuts (19) and remove stub shaft (18).
12. Remove bolts (21) and remove stub shaft (20).
13. Remove locking bolts (23) that hold plate (22) to the cylinder block. Remove plate (22).
14. If studs (24) are loose or the threads are damaged, remove the studs from the front plate.
7/8(W)
w
2020/6/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...