The document provides instructions for removing and installing the inlet manifold on a 314D LCR excavator with a C4.2 engine. It describes removing the fuel manifold, air inlet heater, bolts and clips to remove the inlet manifold. For installation, it describes cleaning and installing new gaskets, bolts, clips and connectors to install the new inlet manifold. Safety notices are provided throughout regarding keeping parts clean and ensuring components are properly positioned.
Caterpillar cat 314 d lcr excavator (prefix txn) service repair manual (txn00...ifosodkmsme
This document provides instructions for removing and installing the inlet manifold, inlet and exhaust valves, and inlet and exhaust valve springs on a Caterpillar C4.2 engine. The removal process involves using various tools to compress springs and rotate the crankshaft to access components. Installation involves cleaning parts, applying new seals, and carefully reassembling components in the reverse order of removal. Precautions are listed to prevent damage and entry of loose parts into the engine.
Caterpillar cat 314 d lcr excavator (prefix txn) service repair manual (txn00...fjskekdmjekm
The document provides instructions for removing and installing the inlet manifold and inlet and exhaust valves on a Caterpillar 314D LCR excavator. The procedures include using various tools to compress springs, remove bolts and clips, and correctly position gaskets and other components. Precautions are outlined to prevent damage and ensure parts are clean prior to installation. Diagrams illustrate the components and steps in the processes.
Caterpillar cat 321 d lcr excavator (prefix nas) service repair manual (nas00...jjskefkskemik
1. The document provides removal and installation instructions for the inlet manifold on a Caterpillar C6.4 engine.
2. Key steps include using tools to remove bolts and clips, disconnecting hoses, and lifting the manifold off using a bracket and lifting device.
3. Installation involves positioning a new gasket, bolting the manifold back into place, reconnecting hoses, and tightening to the specified torques.
Caterpillar cat 321 d lcr excavator (prefix nas) service repair manual (nas00...fujsjfkskemm
This document provides instructions for removing and installing the inlet manifold on a Caterpillar 321D LCR excavator with a C6.4 engine. The removal process involves detaching hoses, removing bolts and clips, and lifting the manifold off using a lifting device. For installation, the gasket and hoses are reattached, bolts are tightened to the specified torques, and the fuel manifold is reinstalled at the end. Separate sections provide similar instructions for removing and installing inlet and exhaust valves, and related components like valve springs. Safety notices are included throughout regarding keeping parts clean and ensuring components are properly secured.
Caterpillar cat 321 d lcr excavator (prefix nas) service repair manual (nas00...udfdesd
This document provides instructions for removing and installing the inlet manifold on a Caterpillar 321D LCR excavator with a C6.4 engine. The removal process involves detaching hoses, removing bolts and clips, and lifting the manifold off using a lifting device. For installation, the gasket and hoses are reattached, bolts are tightened, and clips are reinstalled. Safety notices are provided to keep parts clean and securely lift the manifold due to its weight.
Caterpillar cat 321 d lcr excavator (prefix nas) service repair manual (nas00...ufdjjsekkmdme
This document provides instructions for removing and installing the inlet manifold on a Caterpillar 321D LCR excavator with a C6.4 engine. The removal process involves detaching hoses, removing bolts and clips, and lifting the manifold off using a lifting device. For installation, the gasket and hoses are reattached, bolts are tightened to the specified torques, and the fuel manifold is reinstalled at the end. Separate sections provide similar instructions for removing and installing inlet and exhaust valves, and related components like valve springs. Safety notices are included throughout regarding keeping parts clean and ensuring components are properly secured.
Caterpillar cat 321 d lcr excavator (prefix nas) service repair manual (nas00...fujsjfkkskefsme
1. The document provides removal and installation instructions for an inlet manifold on a Caterpillar 321D LCR excavator. It details using various tools to remove bolts and clips, disconnect hoses, and lift the manifold off the engine.
2. Removal and installation procedures are also given for inlet and exhaust valve springs on the excavator's C6.4 engine. Tools are used to compress springs and rotate the crankshaft to access the valves.
3. Finally, instructions are provided to remove and install inlet and exhaust valves, using tools like a cylinder head repair stand and valve spring compressor. Precautions are emphasized to avoid damage and properly release spring pressure.
Caterpillar cat 311 d lrr excavator (prefix cla) service repair manual (cla00...fjjsekkdmme
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
Caterpillar cat 314 d lcr excavator (prefix txn) service repair manual (txn00...ifosodkmsme
This document provides instructions for removing and installing the inlet manifold, inlet and exhaust valves, and inlet and exhaust valve springs on a Caterpillar C4.2 engine. The removal process involves using various tools to compress springs and rotate the crankshaft to access components. Installation involves cleaning parts, applying new seals, and carefully reassembling components in the reverse order of removal. Precautions are listed to prevent damage and entry of loose parts into the engine.
Caterpillar cat 314 d lcr excavator (prefix txn) service repair manual (txn00...fjskekdmjekm
The document provides instructions for removing and installing the inlet manifold and inlet and exhaust valves on a Caterpillar 314D LCR excavator. The procedures include using various tools to compress springs, remove bolts and clips, and correctly position gaskets and other components. Precautions are outlined to prevent damage and ensure parts are clean prior to installation. Diagrams illustrate the components and steps in the processes.
Caterpillar cat 321 d lcr excavator (prefix nas) service repair manual (nas00...jjskefkskemik
1. The document provides removal and installation instructions for the inlet manifold on a Caterpillar C6.4 engine.
2. Key steps include using tools to remove bolts and clips, disconnecting hoses, and lifting the manifold off using a bracket and lifting device.
3. Installation involves positioning a new gasket, bolting the manifold back into place, reconnecting hoses, and tightening to the specified torques.
Caterpillar cat 321 d lcr excavator (prefix nas) service repair manual (nas00...fujsjfkskemm
This document provides instructions for removing and installing the inlet manifold on a Caterpillar 321D LCR excavator with a C6.4 engine. The removal process involves detaching hoses, removing bolts and clips, and lifting the manifold off using a lifting device. For installation, the gasket and hoses are reattached, bolts are tightened to the specified torques, and the fuel manifold is reinstalled at the end. Separate sections provide similar instructions for removing and installing inlet and exhaust valves, and related components like valve springs. Safety notices are included throughout regarding keeping parts clean and ensuring components are properly secured.
Caterpillar cat 321 d lcr excavator (prefix nas) service repair manual (nas00...udfdesd
This document provides instructions for removing and installing the inlet manifold on a Caterpillar 321D LCR excavator with a C6.4 engine. The removal process involves detaching hoses, removing bolts and clips, and lifting the manifold off using a lifting device. For installation, the gasket and hoses are reattached, bolts are tightened, and clips are reinstalled. Safety notices are provided to keep parts clean and securely lift the manifold due to its weight.
Caterpillar cat 321 d lcr excavator (prefix nas) service repair manual (nas00...ufdjjsekkmdme
This document provides instructions for removing and installing the inlet manifold on a Caterpillar 321D LCR excavator with a C6.4 engine. The removal process involves detaching hoses, removing bolts and clips, and lifting the manifold off using a lifting device. For installation, the gasket and hoses are reattached, bolts are tightened to the specified torques, and the fuel manifold is reinstalled at the end. Separate sections provide similar instructions for removing and installing inlet and exhaust valves, and related components like valve springs. Safety notices are included throughout regarding keeping parts clean and ensuring components are properly secured.
Caterpillar cat 321 d lcr excavator (prefix nas) service repair manual (nas00...fujsjfkkskefsme
1. The document provides removal and installation instructions for an inlet manifold on a Caterpillar 321D LCR excavator. It details using various tools to remove bolts and clips, disconnect hoses, and lift the manifold off the engine.
2. Removal and installation procedures are also given for inlet and exhaust valve springs on the excavator's C6.4 engine. Tools are used to compress springs and rotate the crankshaft to access the valves.
3. Finally, instructions are provided to remove and install inlet and exhaust valves, using tools like a cylinder head repair stand and valve spring compressor. Precautions are emphasized to avoid damage and properly release spring pressure.
Caterpillar cat 311 d lrr excavator (prefix cla) service repair manual (cla00...fjjsekkdmme
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
Caterpillar cat 311 d lrr excavator (prefix cla) service repair manual (cla00...fjjskekmsemm
This document provides the procedure for removing and installing inlet and exhaust valves and valve guides on a Caterpillar C4.2 engine. The procedure involves using various tools to compress springs, remove components in the proper order, clean parts, and inspect for wear. Valves, guides, seals and other components are then reinstalled in the reverse order, taking care to lubricate parts and set components to the correct specifications.
Caterpillar cat 311 d lrr excavator (prefix cla) service repair manual (cla00...fjsekdmmeed
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
1. The document provides instructions for removing and installing the inlet manifold on a Caterpillar 321D LCR EXCAVATOR powered by a C6.4 engine.
2. The removal procedure involves detaching hoses, removing bolts and clips, and lifting the manifold off using a link bracket.
3. The installation procedure specifies cleaning and preparing surfaces, positioning a new gasket, attaching hoses and bolts, and torquing bolts to the specified values.
Caterpillar cat 311 d lrr excavator (prefix cla) service repair manual (cla00...dkdmidkkdk
This document provides instructions for removing and installing inlet and exhaust valves and valve guides on a C4.2 engine. The procedure involves using various tools to compress springs, remove components in the proper order, clean parts, and lubricate components before installation. Precautions are outlined to prevent injury and ensure proper assembly.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing valves, valve guides, and the engine oil cooler. Precautions are outlined to prevent contamination and contain fluids.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing valves, valve guides, and installing new components. The document also describes draining coolant and removing bolts to take off the engine oil cooler.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
Caterpillar cat 236 d skid steer loader (prefix mpw) service repair manual (m...uufjdjdkkksmem
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 236D Skid Steer Loader. It describes using a valve spring compressor tool to compress the springs and remove the valve keepers and springs. When installing new springs, the document specifies installing them with the smaller pitch end downward. Safety precautions are provided to avoid injury from parts propelled by spring force.
Caterpillar cat 236 d skid steer loader (prefix mpw) service repair manual (m...fjsjefskekfmme
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 236D Skid Steer Loader. It describes using a valve spring compressor tool to compress the springs and remove the valve keepers and springs. When installing new springs, the document specifies installing them with the smaller pitch end downward. Safety precautions are provided to avoid injury from parts propelled by spring force.
Caterpillar Cat 336D2 L Excavator (Prefix LAH) Service Repair Manual (LAH0000...pwg56547003
1) The document provides disassembly instructions for a travel motor on an excavator model 336D2 L.
2) It describes 27 steps to disassemble the various components of the travel motor, including removing the motor head assembly, piston assemblies, barrel assembly, springs and seals.
3) Precautions are provided to watch for spring forces and ensure components are marked for correct reassembly.
Caterpillar Cat 336D2 L Excavator (Prefix HBH) Service Repair Manual (HBH0000...pwg56547003
1) The document provides step-by-step instructions for disassembling the travel motor of a 336D2L excavator.
2) It details 27 steps to remove over 50 individual parts, placing components in order and marking locations for reassembly.
3) Special care is required when removing parts under spring pressure or that could fall, and clean-up of fluids is important.
Caterpillar Cat 336D2 L Excavator (Prefix GJA) Service Repair Manual (GJA0000...pwg56547003
1) The document provides step-by-step instructions to disassemble a travel motor from an excavator model 336D2 L.
2) Over 25 steps are outlined to remove components such as the motor head assembly, piston assemblies, barrel assembly, springs, seals and plates.
3) Tools and safety precautions are listed for tasks like removing components under spring pressure.
Caterpillar Cat 336D L Excavator (Prefix ZML) Service Repair Manual (ZML00001...pwg56547003
The document provides instructions for disassembling and assembling a piston pump (hydraulic fan) on an excavator. The disassembly process involves removing 30 individual parts in 11 steps, taking care with any parts under spring tension. The assembly follows the reverse of disassembly and involves positioning and installing 30 parts in 28 steps, ensuring proper bearing end play and lubrication.
Caterpillar Cat 336D L Excavator (Prefix W3K) Service Repair Manual (W3K00001...pwg56547003
This document provides instructions for disassembling and assembling a travel motor. It lists 28 steps to disassemble components such as the head, springs, seals, plates, and piston. It then lists 19 steps to reassemble these components and install new seals and O-rings, ensuring proper alignment of parts and applying thread lock compounds. Tools required include retaining ring pliers, a bearing puller, threaded rod, and eyebolts. Cleanliness is emphasized throughout assembly and replacement of all worn parts.
Caterpillar Cat 336D L Excavator (Prefix MPL) Service Repair Manual (MPL00001...pwg56547003
The document provides instructions for disassembling and assembling the piston pump of an excavator. It details 22 steps for disassembly, removing components like bolts, seals, springs, and bearings. It then details 31 steps for assembly, including cleaning parts, installing bearings, seals, springs, and other components in the reverse order of disassembly. Safety warnings are provided to wear protective equipment when handling spring loaded parts.
Caterpillar Cat 336D L Excavator (Prefix LMG) Service Repair Manual (LMG00001...pwg56547003
The document provides instructions for installing a swivel on an excavator. It describes:
1) Attaching lifting equipment to the swivel and positioning it. 2) Installing a boot, clamp, retainer and bolts to mount the swivel. 3) Connecting hydraulic hose assemblies and fittings. 4) Removing the vacuum cap to complete installation. Proper cleaning and containment of fluids is emphasized.
Caterpillar Cat 336D L Excavator (Prefix L5X) Service Repair Manual (L5X00001...pwg56547003
This document provides instructions for removing and installing the rear gear group and flywheel on a 336D L excavator. The removal procedure involves using various tools to remove bolts, gears, bushings, bearings, and seals. Installation involves cleaning parts and using tools to carefully lower bearings and gears into place while matching specific dimensions, then reinstalling covers, seals, and bolts. Precautions are provided to keep parts clean and properly position oil passages.
Caterpillar Cat 336D L Excavator (Prefix KKT) Service Repair Manual (KKT00001...pwg56547003
The document provides instructions for removing and installing various engine components on Caterpillar 336D and 336D L excavators, including:
1) Removing and installing the engine oil filter base in 3 steps.
2) Removing and installing the engine oil cooler in 2 steps.
3) Removing and installing the hydraulic oil cooler in 5 steps.
4) Removing and installing the air cleaner in 6 steps.
Caterpillar Cat 336D L Excavator (Prefix JRX) Service Repair Manual (JRX00001...pwg56547003
This document provides instructions for disassembling and assembling the final drive of a 336D L Mobile Hydraulic Power Unit. The disassembly procedure involves 25 steps to remove components like gears, seals, springs and housings. The assembly procedure reverses the disassembly process in 22 steps and provides torque specifications for reinstalling components. Tools required include lifting devices, pry bars, driver groups and torque wrenches.
Caterpillar Cat 336D L Excavator (Prefix JBT) Service Repair Manual (JBT00001...pwg56547003
The document provides instructions for removing, disassembling, assembling, and installing a piston motor (hydraulic fan) for Caterpillar 336D and 336D L excavators. The removal process involves detaching hoses and electrical connections, then lifting the fan motor assembly and piston motor. Disassembly requires using various tools to remove individual components like bearings, seals, springs and pistons. Reassembly follows the reverse order, noting requirements like heating/cooling parts and using tools to install retaining rings and seals. Installation connects all hoses and mounts the assembled fan motor assembly back in place.
More Related Content
Similar to Caterpillar Cat 314D LCR Excavator (Prefix TXN) Service Repair Manual (TXN00001 and up).pdf
Caterpillar cat 311 d lrr excavator (prefix cla) service repair manual (cla00...fjjskekmsemm
This document provides the procedure for removing and installing inlet and exhaust valves and valve guides on a Caterpillar C4.2 engine. The procedure involves using various tools to compress springs, remove components in the proper order, clean parts, and inspect for wear. Valves, guides, seals and other components are then reinstalled in the reverse order, taking care to lubricate parts and set components to the correct specifications.
Caterpillar cat 311 d lrr excavator (prefix cla) service repair manual (cla00...fjsekdmmeed
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
1. The document provides instructions for removing and installing the inlet manifold on a Caterpillar 321D LCR EXCAVATOR powered by a C6.4 engine.
2. The removal procedure involves detaching hoses, removing bolts and clips, and lifting the manifold off using a link bracket.
3. The installation procedure specifies cleaning and preparing surfaces, positioning a new gasket, attaching hoses and bolts, and torquing bolts to the specified values.
Caterpillar cat 311 d lrr excavator (prefix cla) service repair manual (cla00...dkdmidkkdk
This document provides instructions for removing and installing inlet and exhaust valves and valve guides on a C4.2 engine. The procedure involves using various tools to compress springs, remove components in the proper order, clean parts, and lubricate components before installation. Precautions are outlined to prevent injury and ensure proper assembly.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing valves, valve guides, and the engine oil cooler. Precautions are outlined to prevent contamination and contain fluids.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing valves, valve guides, and installing new components. The document also describes draining coolant and removing bolts to take off the engine oil cooler.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
Caterpillar cat 236 d skid steer loader (prefix mpw) service repair manual (m...uufjdjdkkksmem
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 236D Skid Steer Loader. It describes using a valve spring compressor tool to compress the springs and remove the valve keepers and springs. When installing new springs, the document specifies installing them with the smaller pitch end downward. Safety precautions are provided to avoid injury from parts propelled by spring force.
Caterpillar cat 236 d skid steer loader (prefix mpw) service repair manual (m...fjsjefskekfmme
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 236D Skid Steer Loader. It describes using a valve spring compressor tool to compress the springs and remove the valve keepers and springs. When installing new springs, the document specifies installing them with the smaller pitch end downward. Safety precautions are provided to avoid injury from parts propelled by spring force.
Similar to Caterpillar Cat 314D LCR Excavator (Prefix TXN) Service Repair Manual (TXN00001 and up).pdf (11)
Caterpillar Cat 336D2 L Excavator (Prefix LAH) Service Repair Manual (LAH0000...pwg56547003
1) The document provides disassembly instructions for a travel motor on an excavator model 336D2 L.
2) It describes 27 steps to disassemble the various components of the travel motor, including removing the motor head assembly, piston assemblies, barrel assembly, springs and seals.
3) Precautions are provided to watch for spring forces and ensure components are marked for correct reassembly.
Caterpillar Cat 336D2 L Excavator (Prefix HBH) Service Repair Manual (HBH0000...pwg56547003
1) The document provides step-by-step instructions for disassembling the travel motor of a 336D2L excavator.
2) It details 27 steps to remove over 50 individual parts, placing components in order and marking locations for reassembly.
3) Special care is required when removing parts under spring pressure or that could fall, and clean-up of fluids is important.
Caterpillar Cat 336D2 L Excavator (Prefix GJA) Service Repair Manual (GJA0000...pwg56547003
1) The document provides step-by-step instructions to disassemble a travel motor from an excavator model 336D2 L.
2) Over 25 steps are outlined to remove components such as the motor head assembly, piston assemblies, barrel assembly, springs, seals and plates.
3) Tools and safety precautions are listed for tasks like removing components under spring pressure.
Caterpillar Cat 336D L Excavator (Prefix ZML) Service Repair Manual (ZML00001...pwg56547003
The document provides instructions for disassembling and assembling a piston pump (hydraulic fan) on an excavator. The disassembly process involves removing 30 individual parts in 11 steps, taking care with any parts under spring tension. The assembly follows the reverse of disassembly and involves positioning and installing 30 parts in 28 steps, ensuring proper bearing end play and lubrication.
Caterpillar Cat 336D L Excavator (Prefix W3K) Service Repair Manual (W3K00001...pwg56547003
This document provides instructions for disassembling and assembling a travel motor. It lists 28 steps to disassemble components such as the head, springs, seals, plates, and piston. It then lists 19 steps to reassemble these components and install new seals and O-rings, ensuring proper alignment of parts and applying thread lock compounds. Tools required include retaining ring pliers, a bearing puller, threaded rod, and eyebolts. Cleanliness is emphasized throughout assembly and replacement of all worn parts.
Caterpillar Cat 336D L Excavator (Prefix MPL) Service Repair Manual (MPL00001...pwg56547003
The document provides instructions for disassembling and assembling the piston pump of an excavator. It details 22 steps for disassembly, removing components like bolts, seals, springs, and bearings. It then details 31 steps for assembly, including cleaning parts, installing bearings, seals, springs, and other components in the reverse order of disassembly. Safety warnings are provided to wear protective equipment when handling spring loaded parts.
Caterpillar Cat 336D L Excavator (Prefix LMG) Service Repair Manual (LMG00001...pwg56547003
The document provides instructions for installing a swivel on an excavator. It describes:
1) Attaching lifting equipment to the swivel and positioning it. 2) Installing a boot, clamp, retainer and bolts to mount the swivel. 3) Connecting hydraulic hose assemblies and fittings. 4) Removing the vacuum cap to complete installation. Proper cleaning and containment of fluids is emphasized.
Caterpillar Cat 336D L Excavator (Prefix L5X) Service Repair Manual (L5X00001...pwg56547003
This document provides instructions for removing and installing the rear gear group and flywheel on a 336D L excavator. The removal procedure involves using various tools to remove bolts, gears, bushings, bearings, and seals. Installation involves cleaning parts and using tools to carefully lower bearings and gears into place while matching specific dimensions, then reinstalling covers, seals, and bolts. Precautions are provided to keep parts clean and properly position oil passages.
Caterpillar Cat 336D L Excavator (Prefix KKT) Service Repair Manual (KKT00001...pwg56547003
The document provides instructions for removing and installing various engine components on Caterpillar 336D and 336D L excavators, including:
1) Removing and installing the engine oil filter base in 3 steps.
2) Removing and installing the engine oil cooler in 2 steps.
3) Removing and installing the hydraulic oil cooler in 5 steps.
4) Removing and installing the air cleaner in 6 steps.
Caterpillar Cat 336D L Excavator (Prefix JRX) Service Repair Manual (JRX00001...pwg56547003
This document provides instructions for disassembling and assembling the final drive of a 336D L Mobile Hydraulic Power Unit. The disassembly procedure involves 25 steps to remove components like gears, seals, springs and housings. The assembly procedure reverses the disassembly process in 22 steps and provides torque specifications for reinstalling components. Tools required include lifting devices, pry bars, driver groups and torque wrenches.
Caterpillar Cat 336D L Excavator (Prefix JBT) Service Repair Manual (JBT00001...pwg56547003
The document provides instructions for removing, disassembling, assembling, and installing a piston motor (hydraulic fan) for Caterpillar 336D and 336D L excavators. The removal process involves detaching hoses and electrical connections, then lifting the fan motor assembly and piston motor. Disassembly requires using various tools to remove individual components like bearings, seals, springs and pistons. Reassembly follows the reverse order, noting requirements like heating/cooling parts and using tools to install retaining rings and seals. Installation connects all hoses and mounts the assembled fan motor assembly back in place.
Caterpillar Cat 336D L Excavator (Prefix J6D) Service Repair Manual (J6D00001...pwg56547003
This document provides instructions for disassembling and assembling the final drive of a 336D L Mobile Hydraulic Power Unit. The 25 step disassembly process removes components like housing, gears, seals and bearings. The 22 step assembly process reverses this to rebuild the final drive, applying loctite and torquing bolts to specification. Tools required include link brackets, crossblocks, drivers and torque wrenches. Safety precautions are noted for releasing spring forces.
Caterpillar Cat 336D L Excavator (Prefix DTS) Service Repair Manual (DTS00001...pwg56547003
This document provides instructions for disassembling and assembling the piston pump (hydraulic fan) of a 336D L excavator. The disassembly procedure involves removing over 30 individual parts in sequenced steps. The assembly procedure instructs putting the parts back together in reverse order and adjusting clearances as needed. Cleaning and inspecting parts is emphasized for proper reassembly.
The document provides instructions for disassembling and assembling the piston pump of an excavator. It details 22 steps for disassembly, removing components like bolts, seals, springs, and bearings. It then details 31 steps for assembly, including cleaning parts, installing bearings, seals, springs, and other components in the reverse order of disassembly. Safety warnings are provided to wear protective equipment when handling spring loaded parts.
The document provides instructions for removing and installing various engine components on Caterpillar 336D and 336D L excavators, including:
1) Removing and installing the engine oil filter base in 3 steps.
2) Removing and installing the engine oil cooler in 2 steps.
3) Removing and installing the hydraulic oil cooler in 5 steps.
4) Removing and installing the air cleaner in 6 steps.
The document provides instructions for removing, disassembling, assembling, and installing a piston motor (hydraulic fan) for Caterpillar 336D and 336D L excavators. The removal process involves detaching hoses and electrical connections, then lifting the fan motor assembly and piston motor. Disassembly requires using various tools to remove individual components like bearings, seals, springs and pistons. Reassembly follows the reverse order, noting requirements like heating/cooling parts and using tools to install retaining rings and seals. Installation connects all hoses and mounts the assembled piston motor back onto the fan motor assembly.
Caterpillar Cat 325D L EXCAVATOR (Prefix T2S) Service Repair Manual (T2S00001...pwg56547003
The document provides instructions to disassemble a final drive for a 325D L excavator. Key steps include:
1. Marking the final drive for alignment and securing it in a repair stand.
2. Removing bolts and lifting devices to extract the cover and internal gears and shafts.
3. Using tools like retaining ring pliers to detach components like carrier assemblies.
4. Pressing shafts from carriers and disassembling carriers by removing pins, washers and gears.
Caterpillar Cat 325D L Excavator (Prefix SCR) Service Repair Manual (SCR00001...pwg56547003
This document provides instructions for removing and installing camshafts on a Caterpillar C7 engine. The summary is:
1. The procedure begins by removing components like the vibration damper, pulley, rocker arms and pushrods.
2. Tools like timing pins and a puller are required to remove the camshaft.
3. The camshaft is removed by inserting timing pins, applying the puller, and removing camshaft bolts.
Caterpillar Cat 325D L Excavator (Prefix NAC) Service Repair Manual (NAC00001...pwg56547003
This document provides assembly instructions for a final drive in 3 steps:
1. Clean all parts thoroughly before assembly and inspect for wear or damage.
2. Apply specified tools, compounds, and brackets to assemble components like bearings, gears, seals and housings.
3. Measure clearances and torque bolts to specified values to correctly assemble and install the final drive. Cleanliness, compound application and torque specifications are critical to the assembly process.
Caterpillar Cat 325D L Excavator (Prefix MCL) Service Repair Manual (MCL00001...pwg56547003
The document provides instructions for disassembling the final drive of a 325D L excavator. It lists required tools and a multi-step process involving removing bolts, gears, carriers, shafts, seals, and other components. Individual parts are to be disassembled from larger assemblies using hammers, punches, and presses. Cleanliness is important to prevent dirt from entering mechanisms during disassembly.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 314D LCR EXCAVATOR TXN
Configuration: 314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02766796
Inlet Manifold - Remove and Install
SMCS - 1058-010
Removal Procedure
Start By:
A. Remove the fuel manifold. Refer to Disassembly and Assembly, "Fuel Manifold (Rail) -
Remove".
B. Remove the air inlet heater. Refer to Disassembly and Assembly, "Air Inlet Heater -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g01375420
1. Remove bolts (1) and remove clip (2) .
Illustration 2 g01384395
2. Remove bolt (4) and remove the washers. Discard the washers.
3. Remove bolts (6) and remove the washers. Discard the washers.
4. Remove bolts (3) and remove manifold (5) .
Illustration 3 g01384434
5. Remove clips (7) .
6. Disconnect harness assemblies (8) .
7. Remove bolts (10) and remove inlet manifold (9) and the gasket.
Installation Procedure
2/4
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Check the gaskets for wear or for damage. Replace the components, if necessary.
Illustration 4 g01384434
1. Position the new inlet manifold gasket. Position inlet manifold (9) and install bolts (10).
Tighten bolts (10) to a torque of 18 ± 2 N·m (13 ± 1 lb ft).
2. Connect harness assemblies (8) and install clips (7) .
Illustration 5 g01384395
3. Position manifold (5) and install bolts (3) .
4. Install new washers and install bolt (4). Tighten bolt (4) to a torque of 34 ± 4 N·m (25 ± 3 lb
ft).
3/4
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 5. Install new washers and install bolts (6). Tighten bolts (6) to a torque of 34 ± 4 N·m (25 ± 3
lb ft).
Illustration 6 g01375420
6. Install clip (2) and install bolts (1) .
End By:
a. Install the air inlet heater. Refer to Disassembly and Assembly, "Air Inlet Heater - Remove
and Install"
b. Install the fuel manifold. Refer to Disassembly and Assembly, "Fuel Manifold (Rail) -
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun May 24 09:10:10 UTC+0800 2020
4/4
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 314D LCR EXCAVATOR TXN
Configuration: 314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02767700
Inlet and Exhaust Valve Springs - Remove and Install
SMCS - 1108-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6195 Valve Spring Compressor 1
B 9U-6198 Crankshaft Turning Tool 1
Start By:
A. Remove the rocker shaft assembly. Refer to Disassembly and Assembly, "Rocker Shaft and
Pushrod - Remove".
B. Remove the valve mechanism cover base. Refer to Disassembly and Assembly, "Valve
Mechanism Cover Base - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: The following procedure should be adopted in order to remove the valve springs when the
cylinder head is installed to the engine.
1/6
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Note: Ensure that the appropriate piston is at top dead center before the valve spring is removed.
Failure to ensure that the piston is at top dead center may allow the valve to drop into the cylinder
bore.
NOTICE
Plug the apertures for the push rods in the cylinder head in order to
prevent the entry of loose parts into the engine.
Illustration 1 g01376301
Illustration 2 g01376302
2/6
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
NOTICE
Ensure that the valve spring is compressed squarely or damage to the
valve stem may occur.
1. Install Tooling (A) into position on the cylinder head in order to compress a valve spring (4)
for the appropriate piston.
2. Use Tooling (A) in order to compress valve spring (4) and open valve (1) slightly.
Note: Do not compress valve spring (4) so that valve spring retainer (3) touches valve stem
seal (5) .
3. Use Tooling (B) in order to rotate the crankshaft carefully, until the piston touches the
valve.
Note: Do not use excessive force to turn the crankshaft. The use of force can result in bent
valve stems.
4. Continue to rotate the crankshaft and gradually release the pressure on Tooling (A) until the
piston is at the top dead center position. The valve is now held in a position that allows
valve spring (4) to be safely removed.
Note: Valve springs must be replaced in pairs for the inlet valve or the exhaust valve of
each cylinder. If all valve springs require replacement the procedure can be carried out on
two cylinders at the same time. The procedure can be carried out on the following pairs of
cylinders. 1 with 4 and 2 with 3. Ensure that all of the valve springs are installed before
changing from one pair of cylinders to another pair of cylinders.
NOTICE
Do not turn the crankshaft while the valve springs are removed.
3/6
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 5. Apply sufficient pressure to Tooling (A) in order to allow removal of valve keepers (2) .
Note: Do not compress valve spring (4) so that valve spring retainer (3) touches valve stem
seal (5) .
Remove valve keepers (2) .
6. Slowly release the pressure on Tooling (A).
7. Remove valve spring retainer (3) and remove valve spring (4) .
8. If necessary, remove valve stem seals (5) .
9. Remove Tooling (A) .
Note: The installation of each set of valve springs (4) must be completed before attempting to
remove the next set of valve springs (4) .
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 9U-6195 Valve Spring Compressor 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 3 g01376913
4/6
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 4 g01376302
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
1. The outer face of the valve guides must be clean and dry before installing the valve stem
seal (5). Install new valve stem seal (5) onto the valve guide.
2. Install valve spring (4) onto the cylinder head. Position valve spring retainer (3) on valve
spring (4) .
3. Install Tooling (A) in the appropriate position on the cylinder head in order to compress
valve spring (4) .
4. Apply sufficient pressure to Tooling (A) in order to install valve keepers (2). Do not
compress valve spring (4) so that valve spring retainer (3) touches valve stem seal (5) .
5. Carefully release the pressure on Tooling (A) .
End By:
a. Install the valve mechanism cover base. Refer to Disassembly and Assembly, "Valve
Mechanism Cover Base - Remove and Install".
5/6
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. b. Install the rocker shaft assembly. Refer to Disassembly and Assembly, "Rocker Shaft and
Pushrod - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun May 24 09:11:07 UTC+0800 2020
6/6
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 314D LCR EXCAVATOR TXN
Configuration: 314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02767800
Inlet and Exhaust Valves - Remove and Install
SMCS - 1105-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8S-6691 Cylinder Head Repair Stand 1
B 9U-6195 Valve Spring Compressor Gp 1
C 5P-1720 Seal Pick 1
Start By:
A. Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Note the location and orientation of all components for assembly purposes.
1. Clean the bottom face of the cylinder head. Check the depth of the valves below the face of
the cylinder head before the valve springs are removed. Refer to Specifications, "Cylinder
Head Valves" for the correct dimensions.
1/6
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. 2. Place a temporary identification mark on the heads of the valves in order to identify the
correct position.
Illustration 1 g01376164
Typical Example
3. Use a suitable lifting device in order to position cylinder head (1) onto Tooling (A) with the
valve springs upward. The weight of cylinder head (1) is approximately 70 kg (155 lb).
Note: Ensure that cylinder head (1) is kept on a clean, soft surface in order to prevent
damage to the machined face.
Illustration 2 g01376174
2/6
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 3 g01376184
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
4. Install Tooling (B) on cylinder head (1) in order to compress valve spring (5) .
NOTICE
Ensure that the valve spring is compressed squarely or damage to the
valve stem may occur.
5. Apply sufficient pressure to Tooling (B) in order to remove valve keepers (3). Do not
compress the spring so that valve spring retainer (4) touches valve stem seal (6) .
6. Slowly release the pressure on Tooling (B) .
7. Remove valve spring retainer (4). Remove valve spring (5). Remove valve (2) .
8. Use Tooling (C) in order to remove valve stem seal (6) .
3/6
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 9. Repeat Steps 4 through 7 for the remaining valves.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 8S-6691 Cylinder Head Repair Stand 1
B 9U-6195 Valve Spring Compressor Gp 1
D 312-8755 Valve Stem Seal Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean all components of the cylinder head assembly. Ensure that all ports, all coolant
passages and all lubrication passages in the cylinder head are free from debris. Follow Steps
1.a through 1.d in order to inspect the components of the cylinder head assembly. Replace
any components that are worn or damaged.
a. Inspect the cylinder head for wear and for damage. Refer to Testing and Adjusting,
"Cylinder Head Inspect".
b. Inspect the valve seats for wear and for damage. Refer to Specifications, "Cylinder
Head Valves" for further information.
c. Inspect the valve guides for wear and for damage. Refer to Specifications, "Cylinder
Head Valves" and Testing and Adjusting, "Valve Guide - Inspect" for further
information.
d. Inspect the valves for wear and for damage. Refer to Specifications, "Cylinder Head
Valves ".
e. Inspect valve springs (5) for damage and for the correct length. Refer to
Specifications, "Cylinder Head Valves ".
4/6
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 4 g01376184
Illustration 5 g01376926
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
2. Lubricate the stem of valve (2) with clean engine oil. Install valve (2) in the appropriate
position in the cylinder head. Check the depth of valve (2) below the face of the cylinder
head. Refer to Testing and Adjusting, "Valve Depth - Inspect" for more information.
5/6
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. 3. The outer face of the valve guides must be clean and dry before installing the valve stem
seal (6). Use Tooling (C) in order to install new valve stem seal (6) onto the valve guide.
4. Install valve spring (5) onto the cylinder head. Position valve spring retainer (4) on valve
spring (5) .
5. Install Tooling (B) in the appropriate position on cylinder head (1) in order to compress
valve spring (5) .
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
6. Apply sufficient pressure to Tooling (B) in order to install valve keepers (3). Do not
compress spring (5) so that valve spring retainer (4) touches valve stem seal (6) .
7. Carefully release the pressure on Tooling (B) .
8. Repeat Steps 2 through 7 for the remaining valves.
End By: Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun May 24 09:12:03 UTC+0800 2020
6/6
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 314D LCR EXCAVATOR TXN
Configuration: 314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i04625005
Inlet and Exhaust Valve Guides - Remove and Install
SMCS - 1104-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 384-8861 Valve Guide Remover 1
B 138-7573 Link Bracket 4
C 1U-9200 Lever Puller Hoist 1
D 8S-6691 Cylinder Head Repair Stand 1
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
B. Remove the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injector - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: Refer to Special Instructions, SMHS7953-00, "Use of Valve Seat Insert Puller Group" to
aid with the removal of the inlet and exhaust valve seats.
Illustration 1 g01377064
Typical Example
1. Attach Tooling (B) , Tooling (C) , and a suitable lifting device to cylinder head (1) . Use
Tooling (B) , Tooling (C) , and the suitable lifting device in order to turn over cylinder head
(1) by 180° onto Tooling (D) .
2/4
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 2 g01377121
2. Use Tooling (A) in order to remove valve guides (2) (not shown).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
E 384-8862 Valve Guide Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
3/4
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 3 g01377130
1. Lubricate the outside of valve guides (2) (not shown) with clean engine oil.
2. Use Tooling (E) in order to install new valve guides (2) . Install valve guide (2) so that
valve guide (2) protrudes 16.000 mm (0.6299 inch) above Surface (X) of cylinder head (1) .
End By:
a. Install the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injector - Install".
b. Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and Exhaust
Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun May 24 09:13:00 UTC+0800 2020
4/4
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 314D LCR EXCAVATOR TXN
Configuration: 314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02768108
Engine Oil Cooler - Remove
SMCS - 1378-011
Removal Procedure
Start By:
A. Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump
- Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/2
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. 1. Drain the coolant into a suitable container for storage or disposal. Refer to Operation and
Maintenance Manual, "Cooling System Coolant (ELC) - Change".
Illustration 1 g01384719
2. Remove bolts (1) .
3. Remove bolts (2) and remove engine oil cooler (3). Remove gasket (4) (not shown) from the
engine cylinder block.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun May 24 09:13:57 UTC+0800 2020
2/2
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 314D LCR EXCAVATOR TXN
Configuration: 314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02746254
Engine Oil Cooler - Disassemble
SMCS - 1378-015
Disassembly Procedure
Start By:
a. Remove the engine oil cooler. Refer to Disassembly and Assembly, "Engine Oil Cooler - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior of the
components should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism. Precision components can be damaged by contaminants or by dirt. Perform disassembly
procedures on a clean work surface. Keep components covered and protected at all times.
1/2
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 1 g01375411
1. Remove bolts (9) and the washers. Remove cover (8) and gasket (7).
2. Remove nuts (5) and the washers from engine oil cooler cover (4). Remove nuts (6) and the washers
from engine oil cooler cover (4).
3. Remove engine oil cooler core (2) from engine oil cooler cover (4). Remove gaskets (1) and (3).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun May 24 09:14:54 UTC+0800 2020
2/2
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
27. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 314D LCR EXCAVATOR TXN
Configuration: 314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02746255
Engine Oil Cooler - Assemble
SMCS - 1378-016
Assembly Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning fluid.
Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts
which may cause trouble. Inspect all parts. If any parts are worn or damaged, use new parts for
replacement. Dirt and other contaminants can damage the precision component. Perform assembly
procedures on a clean work surface. Keep components covered and protected at all times.
Note: Check the gaskets for damage. Replace the components, if necessary.
1/2
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Illustration 1 g01375411
1. Install gaskets (3) and (1) to engine oil cooler core (2). Position engine oil cooler core (2) to engine
oil cooler cover (4).
2. Install the washers and nuts (6). Install the washers and nuts (5).
3. Install gasket (7) and position cover (8). Install the washers and bolts (9).
End By:
a. Install the engine oil cooler. Refer to Disassembly and Assembly, "Engine Oil Cooler - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun May 24 09:15:50 UTC+0800 2020
2/2
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 314D LCR EXCAVATOR TXN
Configuration: 314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02768201
Engine Oil Cooler - Install
SMCS - 1378-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Check the gaskets for wear or for damage. Replace the components, if necessary.
Illustration 1 g01384719
1/2
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...