The document provides instructions for removing and installing various engine components on a Caterpillar 312C excavator, including:
- Flywheel installation which requires heating the ring gear and pressing it onto the flywheel before securing with bolts.
- Crankshaft rear seal removal using a slide hammer puller and distorter tool, and installation using a installer tool and retaining compound.
- Flywheel housing removal by lifting with straps after removing bolts, and installation by cleaning the mating surfaces and securing with bolts.
- Crankshaft pulley removal using a puller and chisel if needed, and installation by positioning on the engine and tightening the nut.
Caterpillar cat 323 d l excavator (prefix pbe) service repair manual (pbe0000...fjjsekmsmmes
This document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar C6.4 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing and idler shaft. The installation procedure specifies cleaning parts and using a press and driver group to re-install components in reverse order, checking backlash and end play tolerances.
Caterpillar cat 312 c excavator (prefix bnn) service repair manual (bnn00001 ...fjskkksmemm
This document provides instructions for disassembling the final drive, travel motor, and travel counterbalance valve of excavator models 312C and 312C L. It outlines 19 steps to fully disassemble these components, including draining fluids, removing sprockets, valves, plates, seals, springs, and other internal parts. Safety notices are provided throughout to warn of hazards like stored energy, flying parts, and hot or pressurized fluids. Required specialty tools are listed at the beginning.
Caterpillar cat 312 c excavator (prefix cba) service repair manual (cba00001 ...fjskkksmemm
This document provides instructions for removing and installing the engine oil bypass valve on Caterpillar 312C and 312C L excavators. It describes removing the threaded plug, shim, spring, and spring seat from the cylinder block. When installing, the spring seat, spring, shim, and threaded plug are reinstalled and tightened to the specified torque. The document also notes steps for checking components and adjusting valve opening pressure.
Caterpillar cat 312 c excavator (prefix cba) service repair manual (cba01201 ...fjskkksmemm
The document provides instructions for removing and installing various engine components on Caterpillar 312C and 312C L excavators, including:
- Installing a crankshaft rear seal using a specific tool and applying retaining compound to mating parts.
- Removing and installing a flywheel housing which requires removing bolts and installing a new gasket.
- Removing a crankshaft pulley using a puller tool and removing a wear sleeve with a chisel if needed.
- Removing a crankshaft front seal by drilling holes and using a slide hammer puller.
- Installing a new crankshaft front seal with a specific installer tool.
- Procedures are provided for additional
Caterpillar cat 312 c excavator (prefix bwh) service repair manual (bwh00001 ...fjskkksmemm
The document provides instructions for removing and installing a crankshaft pulley on a 312C excavator. The removal procedure involves using a puller tool to remove the pulley from the crankshaft. For installation, the pulley is pressed onto the crankshaft and secured with bolts that are tightened to the specified torque.
Caterpillar cat 330 f excavator (prefix hck) service repair manual (hck00001 ...fjskkksmemm
The document is a service repair manual that provides instructions for disassembling a 330F excavator travel motor. It outlines 28 steps to fully disassemble the travel motor, removing components like the head assembly, housing assembly, brake piston, rotating group, pistons, and more. Various tools are required to remove fasteners and components. Safety precautions are provided throughout to warn of spring forces, pressurized fluids, and other hazards during disassembly.
Caterpillar cat 312 b l track type excavator (prefix 9gr) service repair manu...fjskkksmemm
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B excavator engine. It describes:
1) Removing bolts and washers to detach the flywheel housing adapter, then removing the adapter.
2) Removing bolts to separate the inner ring from the flywheel, then removing the ring.
3) Lifting the flywheel out of the housing using straps and a lifting device, as it weighs 50kg.
The installation section reverses the removal steps, heating the ring gear if it was removed previously, and includes checking flywheel runout after installation.
Caterpillar cat 330 f ln excavator (prefix wba) service repair manual (wba000...fksjksmmde
The document provides step-by-step instructions to disassemble a travel motor. It begins by listing required tools and fasteners. The procedures then describe how to remove 27 components of the travel motor including the head assembly, housing assembly, brake piston, rotating group, pistons, and seals. Detailed illustrations accompany each step to show how to properly disassemble the travel motor.
Caterpillar cat 323 d l excavator (prefix pbe) service repair manual (pbe0000...fjjsekmsmmes
This document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar C6.4 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing and idler shaft. The installation procedure specifies cleaning parts and using a press and driver group to re-install components in reverse order, checking backlash and end play tolerances.
Caterpillar cat 312 c excavator (prefix bnn) service repair manual (bnn00001 ...fjskkksmemm
This document provides instructions for disassembling the final drive, travel motor, and travel counterbalance valve of excavator models 312C and 312C L. It outlines 19 steps to fully disassemble these components, including draining fluids, removing sprockets, valves, plates, seals, springs, and other internal parts. Safety notices are provided throughout to warn of hazards like stored energy, flying parts, and hot or pressurized fluids. Required specialty tools are listed at the beginning.
Caterpillar cat 312 c excavator (prefix cba) service repair manual (cba00001 ...fjskkksmemm
This document provides instructions for removing and installing the engine oil bypass valve on Caterpillar 312C and 312C L excavators. It describes removing the threaded plug, shim, spring, and spring seat from the cylinder block. When installing, the spring seat, spring, shim, and threaded plug are reinstalled and tightened to the specified torque. The document also notes steps for checking components and adjusting valve opening pressure.
Caterpillar cat 312 c excavator (prefix cba) service repair manual (cba01201 ...fjskkksmemm
The document provides instructions for removing and installing various engine components on Caterpillar 312C and 312C L excavators, including:
- Installing a crankshaft rear seal using a specific tool and applying retaining compound to mating parts.
- Removing and installing a flywheel housing which requires removing bolts and installing a new gasket.
- Removing a crankshaft pulley using a puller tool and removing a wear sleeve with a chisel if needed.
- Removing a crankshaft front seal by drilling holes and using a slide hammer puller.
- Installing a new crankshaft front seal with a specific installer tool.
- Procedures are provided for additional
Caterpillar cat 312 c excavator (prefix bwh) service repair manual (bwh00001 ...fjskkksmemm
The document provides instructions for removing and installing a crankshaft pulley on a 312C excavator. The removal procedure involves using a puller tool to remove the pulley from the crankshaft. For installation, the pulley is pressed onto the crankshaft and secured with bolts that are tightened to the specified torque.
Caterpillar cat 330 f excavator (prefix hck) service repair manual (hck00001 ...fjskkksmemm
The document is a service repair manual that provides instructions for disassembling a 330F excavator travel motor. It outlines 28 steps to fully disassemble the travel motor, removing components like the head assembly, housing assembly, brake piston, rotating group, pistons, and more. Various tools are required to remove fasteners and components. Safety precautions are provided throughout to warn of spring forces, pressurized fluids, and other hazards during disassembly.
Caterpillar cat 312 b l track type excavator (prefix 9gr) service repair manu...fjskkksmemm
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B excavator engine. It describes:
1) Removing bolts and washers to detach the flywheel housing adapter, then removing the adapter.
2) Removing bolts to separate the inner ring from the flywheel, then removing the ring.
3) Lifting the flywheel out of the housing using straps and a lifting device, as it weighs 50kg.
The installation section reverses the removal steps, heating the ring gear if it was removed previously, and includes checking flywheel runout after installation.
Caterpillar cat 330 f ln excavator (prefix wba) service repair manual (wba000...fksjksmmde
The document provides step-by-step instructions to disassemble a travel motor. It begins by listing required tools and fasteners. The procedures then describe how to remove 27 components of the travel motor including the head assembly, housing assembly, brake piston, rotating group, pistons, and seals. Detailed illustrations accompany each step to show how to properly disassemble the travel motor.
Caterpillar cat 312 c l excavator (prefix dbn) service repair manual (dbn0000...fksjksmmde
The document provides instructions for removing and installing a fuel injection pump on a Caterpillar 3064 engine. It describes:
1) Removing the fuel lines, access cover, and mounting bolts to detach the pump.
2) Installing a new gasket and securing bolts to reattach the pump, ensuring proper alignment.
3) Reconnecting the fuel lines once the pump is secured.
Caterpillar cat 336 d2 l excavator (prefix dgr) service repair manual (dgr000...pfiskdmjekm
This document provides instructions for removing and installing a unit injector and unit injector sleeve on a Caterpillar C9 engine. It outlines the required tools and gives step-by-step instructions that include disconnecting fuel lines and electrical connections, cleaning parts, replacing seals, and torquing bolts to specifications. Proper cleaning and installation of parts is emphasized to prevent leaks and engine damage.
Caterpillar cat 320 d l excavator (prefix kgf) service repair manual (kgf0000...fkjsekksmem
This document provides instructions for disassembling and assembling the travel motor of a 320D L excavator. The disassembly process includes 27 steps to remove components like the head, fittings, seals, brake piston, plates, and barrel assembly. The assembly section outlines 13 steps including installing seals, keys, cam plate, springs, and piston shoe assemblies back into the barrel assembly and body of the travel motor. Special care must be taken to align parts properly and not allow components to separate during disassembly and assembly.
This document provides instructions for removing the engine oil filter base and oil cooler from a Caterpillar 329D LN excavator. The key steps are:
1. Drain engine oil and coolant from the systems before removal to contain fluids.
2. For a remote-mounted filter base, use a strap wrench to remove the oil filter, then remove bolts and the filter base.
3. For an engine-mounted base, drain the cooling system, then remove hoses and bolts to separate the oil cooler from the engine.
Caterpillar cat 312 d l excavator (prefix rhl) service repair manual (rhl0000...pfiskdmjekm
The document provides instructions for removing and installing an idler gear on a Caterpillar C4.2 engine. It describes:
1) Removing the front housing, idler gear bolt and washer, thrust plate, and idler gear from the idler gear shaft.
2) Using a puller tool to remove the idler gear bushing and idler shaft from the cylinder block.
3) Checking the idler shaft for wear and replacing if needed.
4) Measuring gear backlash and end play during installation and comparing to specifications.
This document provides instructions for installing a flywheel and removing and installing a wet back end flywheel housing on a Caterpillar 320 GC excavator. It describes using guide studs and lifting devices to position the heavy flywheel and housing. Torque specifications and tightening sequences are given for installing mounting bolts. Replacing seals, gaskets and dowels is also covered.
Caterpillar cat 120 g motor grader (prefix 11w) service repair manual (11w010...fjsekdmmeed
This document provides instructions for removing and installing various engine components on a Caterpillar 120G motor grader, including the cylinder head, spacer plate, and water directors. The removal and installation procedures describe removing bolts and other fasteners, lifting components, cleaning surfaces, applying sealants, and torquing bolts to specified values. Safety notices are included to handle fluids properly and avoid contaminating parts.
Caterpillar cat 312 c l excavator (prefix bwh) service repair manual (bwh0000...fjskkksmemm
The document provides instructions for removing and installing various engine components on a Caterpillar 312C excavator, including:
- Removing and installing the flywheel, which requires drilling holes in the crankshaft rear seal before removal.
- Removing the crankshaft rear seal and wear sleeve using slide hammer and seal distorter tools.
- Installing a new crankshaft rear seal and wear sleeve using an installer tool and retaining compound.
- Removing and installing the flywheel housing, which requires removing bolts and installing a new gasket.
- Removing the crankshaft pulley using a puller tool and removing the wear sleeve using a chisel if needed.
Caterpillar cat 312 d excavator (prefix phh) service repair manual (phh00001 ...dueikdkmem
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. The procedure includes removing the electric starting motor and flywheel first. Then a lifting device and link bracket are used to remove the housing bolts and housing. The oil seal is then removed from the housing using a driver group. For installation, a new oil seal is installed using the driver group before positioning the housing on the cylinder block with a new gasket and securing bolts. The flywheel and starting motor are then reinstalled at the end.
Caterpillar cat 312 d excavator (prefix phh) service repair manual (phh00001 ...cdfzxs
This document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. The summary is:
1. Tools and parts required are listed, including a link bracket and driver group.
2. Removal instructions include removing the electric starting motor, flywheel, bolts securing the housing, and oil seal.
3. Installation instructions specify cleaning surfaces, installing a new gasket and oil seal, positioning the housing, and reinstalling the bolts, flywheel, and electric starting motor.
Caterpillar cat 312 d excavator (prefix phh) service repair manual (phh00001 ...fjskekxcddmmme
This document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. The removal procedure involves using a link bracket and driver group to detach the housing after removing the electric starting motor and flywheel. The installation procedure specifies using a primer and retaining compound on the mating parts and attaching the housing with bolts, then reinstalling the starting motor and flywheel.
Caterpillar cat 312 d l excavator (prefix phh) service repair manual (phh0000...fhjsjkdmemm
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. The procedures include:
1) Removing the electric starting motor and flywheel first.
2) Using lifting tools to remove the housing bolts and housing.
3) Inspecting and replacing the dowels and gasket if needed.
4) Cleaning the mating surfaces and installing the new gasket on the cylinder block.
5) Placing the housing back in position and securing it with bolts.
Caterpillar cat 312 d l excavator (prefix phh) service repair manual (phh0000...fjjskmdmem
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove the bolts securing the housing and take off the housing.
3) Removing the oil seal from the housing.
4) Cleaning surfaces and installing a new gasket before reinstalling the housing with new bolts and reinstalling the flywheel.
This document provides instructions for removing and installing various engine components on Caterpillar 320C excavators, including the flywheel, crankshaft rear seal, flywheel housing, crankshaft pulley, and crankshaft front seal. The procedures describe using various tools to remove and install each part, provide notices about cleanliness and fluid containment, and note related removal and installation steps for other components.
Caterpillar Cat 320C L Excavator (Prefix DBG) Service Repair Manual (DBG00001...hvy7sbkw8e
This document provides instructions for installing and removing various engine components on Caterpillar 320C excavators, including:
- Installing the flywheel by attaching it with bolts and checking runout.
- Removing and installing the crankshaft rear seal using tools like a slide hammer and installer.
- Removing and installing the flywheel housing which requires lifting equipment and replacing the oil seal.
- Procedures for the crankshaft pulley which involves removing nuts and a wear sleeve, and installing with a torque wrench.
- Removing the crankshaft front seal using a slide hammer puller.
This document provides instructions for removing and installing various engine components on Caterpillar 320C excavators, including the flywheel, crankshaft rear seal, flywheel housing, crankshaft pulley, and crankshaft front seal. The procedures describe using various tools to remove components and clean surfaces, and installing replacement parts with adhesives or by pressing/bolting into place. Safety notices are provided to handle parts carefully and contain fluids.
Kubota m5500 dt tractor parts catalogue manualdfjjsjkemmm
The document provides instructions and part listings for a parts book. It defines the column headings used on part number pages, including reference number, part number, description, quantity, serial number range, interchangeability, and remarks. It also notes country codes that may be included to indicate part differences by country. The summary lists the main document sections and provides an example part listing for a crankcase.
Kubota m5040 hdc tractor parts catalogue manualdfjjsjkemmm
The document provides parts information for an engine, including:
- Descriptions of column headings for part number pages like part number, name, quantity, etc.
- Parts lists organized by component (e.g. crankcase, oil pan, cylinder head) with part numbers, names, quantities, and other details.
- Notes on country codes used for parts that may differ between countries.
Kubota l4610 dt hst tractor parts catalogue manualdfjjsjkemmm
This document provides part numbers and descriptions for a crankcase, including the crankcase itself along with various plugs, caps, pins, and other component parts. Key information includes the part number, description, quantity used, applicable serial number range, interchangeability, and remarks.
Kubota l4400 h tractor parts catalogue manualdfjjsjkemmm
The document provides instructions and part numbers for a parts book. It defines the column headings used on part number pages, including reference number, part number, part name, quantity, serial number range, and remarks. It notes country codes that may be included and what they indicate. Sample pages from the parts book are then provided that list part numbers, descriptions, quantities and other details for specific assembly items like the crankcase, oil pan, cylinder head, gear case and more.
Kubota l4310 dt gst-chst-c tractor parts catalogue manualdfjjsjkemmm
The document provides instructions and definitions for parts books. It explains that the parts book headings will match the picture pages. It defines the column headings for part number pages, including reference number, part number, description, quantity, serial number range, interchangeability, and remarks. It also notes country codes that may be included to indicate part differences by country.
Kubota l3410 hst tractor parts catalogue manualdfjjsjkemmm
This document provides instructions and definitions for parts books. It explains the column headings used on parts number pages, including the reference number, part number, description, quantity, serial number range, interchangeability, and remarks. Country codes that may be included are also defined. An example page from the parts book is then shown listing specific part numbers, descriptions, and the book they can be found in.
Caterpillar cat 312 c l excavator (prefix dbn) service repair manual (dbn0000...fksjksmmde
The document provides instructions for removing and installing a fuel injection pump on a Caterpillar 3064 engine. It describes:
1) Removing the fuel lines, access cover, and mounting bolts to detach the pump.
2) Installing a new gasket and securing bolts to reattach the pump, ensuring proper alignment.
3) Reconnecting the fuel lines once the pump is secured.
Caterpillar cat 336 d2 l excavator (prefix dgr) service repair manual (dgr000...pfiskdmjekm
This document provides instructions for removing and installing a unit injector and unit injector sleeve on a Caterpillar C9 engine. It outlines the required tools and gives step-by-step instructions that include disconnecting fuel lines and electrical connections, cleaning parts, replacing seals, and torquing bolts to specifications. Proper cleaning and installation of parts is emphasized to prevent leaks and engine damage.
Caterpillar cat 320 d l excavator (prefix kgf) service repair manual (kgf0000...fkjsekksmem
This document provides instructions for disassembling and assembling the travel motor of a 320D L excavator. The disassembly process includes 27 steps to remove components like the head, fittings, seals, brake piston, plates, and barrel assembly. The assembly section outlines 13 steps including installing seals, keys, cam plate, springs, and piston shoe assemblies back into the barrel assembly and body of the travel motor. Special care must be taken to align parts properly and not allow components to separate during disassembly and assembly.
This document provides instructions for removing the engine oil filter base and oil cooler from a Caterpillar 329D LN excavator. The key steps are:
1. Drain engine oil and coolant from the systems before removal to contain fluids.
2. For a remote-mounted filter base, use a strap wrench to remove the oil filter, then remove bolts and the filter base.
3. For an engine-mounted base, drain the cooling system, then remove hoses and bolts to separate the oil cooler from the engine.
Caterpillar cat 312 d l excavator (prefix rhl) service repair manual (rhl0000...pfiskdmjekm
The document provides instructions for removing and installing an idler gear on a Caterpillar C4.2 engine. It describes:
1) Removing the front housing, idler gear bolt and washer, thrust plate, and idler gear from the idler gear shaft.
2) Using a puller tool to remove the idler gear bushing and idler shaft from the cylinder block.
3) Checking the idler shaft for wear and replacing if needed.
4) Measuring gear backlash and end play during installation and comparing to specifications.
This document provides instructions for installing a flywheel and removing and installing a wet back end flywheel housing on a Caterpillar 320 GC excavator. It describes using guide studs and lifting devices to position the heavy flywheel and housing. Torque specifications and tightening sequences are given for installing mounting bolts. Replacing seals, gaskets and dowels is also covered.
Caterpillar cat 120 g motor grader (prefix 11w) service repair manual (11w010...fjsekdmmeed
This document provides instructions for removing and installing various engine components on a Caterpillar 120G motor grader, including the cylinder head, spacer plate, and water directors. The removal and installation procedures describe removing bolts and other fasteners, lifting components, cleaning surfaces, applying sealants, and torquing bolts to specified values. Safety notices are included to handle fluids properly and avoid contaminating parts.
Caterpillar cat 312 c l excavator (prefix bwh) service repair manual (bwh0000...fjskkksmemm
The document provides instructions for removing and installing various engine components on a Caterpillar 312C excavator, including:
- Removing and installing the flywheel, which requires drilling holes in the crankshaft rear seal before removal.
- Removing the crankshaft rear seal and wear sleeve using slide hammer and seal distorter tools.
- Installing a new crankshaft rear seal and wear sleeve using an installer tool and retaining compound.
- Removing and installing the flywheel housing, which requires removing bolts and installing a new gasket.
- Removing the crankshaft pulley using a puller tool and removing the wear sleeve using a chisel if needed.
Caterpillar cat 312 d excavator (prefix phh) service repair manual (phh00001 ...dueikdkmem
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. The procedure includes removing the electric starting motor and flywheel first. Then a lifting device and link bracket are used to remove the housing bolts and housing. The oil seal is then removed from the housing using a driver group. For installation, a new oil seal is installed using the driver group before positioning the housing on the cylinder block with a new gasket and securing bolts. The flywheel and starting motor are then reinstalled at the end.
Caterpillar cat 312 d excavator (prefix phh) service repair manual (phh00001 ...cdfzxs
This document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. The summary is:
1. Tools and parts required are listed, including a link bracket and driver group.
2. Removal instructions include removing the electric starting motor, flywheel, bolts securing the housing, and oil seal.
3. Installation instructions specify cleaning surfaces, installing a new gasket and oil seal, positioning the housing, and reinstalling the bolts, flywheel, and electric starting motor.
Caterpillar cat 312 d excavator (prefix phh) service repair manual (phh00001 ...fjskekxcddmmme
This document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. The removal procedure involves using a link bracket and driver group to detach the housing after removing the electric starting motor and flywheel. The installation procedure specifies using a primer and retaining compound on the mating parts and attaching the housing with bolts, then reinstalling the starting motor and flywheel.
Caterpillar cat 312 d l excavator (prefix phh) service repair manual (phh0000...fhjsjkdmemm
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. The procedures include:
1) Removing the electric starting motor and flywheel first.
2) Using lifting tools to remove the housing bolts and housing.
3) Inspecting and replacing the dowels and gasket if needed.
4) Cleaning the mating surfaces and installing the new gasket on the cylinder block.
5) Placing the housing back in position and securing it with bolts.
Caterpillar cat 312 d l excavator (prefix phh) service repair manual (phh0000...fjjskmdmem
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove the bolts securing the housing and take off the housing.
3) Removing the oil seal from the housing.
4) Cleaning surfaces and installing a new gasket before reinstalling the housing with new bolts and reinstalling the flywheel.
This document provides instructions for removing and installing various engine components on Caterpillar 320C excavators, including the flywheel, crankshaft rear seal, flywheel housing, crankshaft pulley, and crankshaft front seal. The procedures describe using various tools to remove and install each part, provide notices about cleanliness and fluid containment, and note related removal and installation steps for other components.
Caterpillar Cat 320C L Excavator (Prefix DBG) Service Repair Manual (DBG00001...hvy7sbkw8e
This document provides instructions for installing and removing various engine components on Caterpillar 320C excavators, including:
- Installing the flywheel by attaching it with bolts and checking runout.
- Removing and installing the crankshaft rear seal using tools like a slide hammer and installer.
- Removing and installing the flywheel housing which requires lifting equipment and replacing the oil seal.
- Procedures for the crankshaft pulley which involves removing nuts and a wear sleeve, and installing with a torque wrench.
- Removing the crankshaft front seal using a slide hammer puller.
This document provides instructions for removing and installing various engine components on Caterpillar 320C excavators, including the flywheel, crankshaft rear seal, flywheel housing, crankshaft pulley, and crankshaft front seal. The procedures describe using various tools to remove components and clean surfaces, and installing replacement parts with adhesives or by pressing/bolting into place. Safety notices are provided to handle parts carefully and contain fluids.
Similar to Caterpillar cat 312 c l excavator (prefix bwh) service repair manual (bwh00001 and up) (9)
Kubota m5500 dt tractor parts catalogue manualdfjjsjkemmm
The document provides instructions and part listings for a parts book. It defines the column headings used on part number pages, including reference number, part number, description, quantity, serial number range, interchangeability, and remarks. It also notes country codes that may be included to indicate part differences by country. The summary lists the main document sections and provides an example part listing for a crankcase.
Kubota m5040 hdc tractor parts catalogue manualdfjjsjkemmm
The document provides parts information for an engine, including:
- Descriptions of column headings for part number pages like part number, name, quantity, etc.
- Parts lists organized by component (e.g. crankcase, oil pan, cylinder head) with part numbers, names, quantities, and other details.
- Notes on country codes used for parts that may differ between countries.
Kubota l4610 dt hst tractor parts catalogue manualdfjjsjkemmm
This document provides part numbers and descriptions for a crankcase, including the crankcase itself along with various plugs, caps, pins, and other component parts. Key information includes the part number, description, quantity used, applicable serial number range, interchangeability, and remarks.
Kubota l4400 h tractor parts catalogue manualdfjjsjkemmm
The document provides instructions and part numbers for a parts book. It defines the column headings used on part number pages, including reference number, part number, part name, quantity, serial number range, and remarks. It notes country codes that may be included and what they indicate. Sample pages from the parts book are then provided that list part numbers, descriptions, quantities and other details for specific assembly items like the crankcase, oil pan, cylinder head, gear case and more.
Kubota l4310 dt gst-chst-c tractor parts catalogue manualdfjjsjkemmm
The document provides instructions and definitions for parts books. It explains that the parts book headings will match the picture pages. It defines the column headings for part number pages, including reference number, part number, description, quantity, serial number range, interchangeability, and remarks. It also notes country codes that may be included to indicate part differences by country.
Kubota l3410 hst tractor parts catalogue manualdfjjsjkemmm
This document provides instructions and definitions for parts books. It explains the column headings used on parts number pages, including the reference number, part number, description, quantity, serial number range, interchangeability, and remarks. Country codes that may be included are also defined. An example page from the parts book is then shown listing specific part numbers, descriptions, and the book they can be found in.
Kubota l3410 gst tractor parts catalogue manualdfjjsjkemmm
This document provides instructions and definitions for parts books. It explains the column headings used on parts number pages, including the reference number, part number, description, quantity, serial number range, interchangeability, and remarks. Country codes that may be included are also defined. An example page from the parts book is then shown listing specific part numbers, descriptions, and the book they can be found in.
Kubota l3410 dt tractor parts catalogue manualdfjjsjkemmm
This document provides instructions and definitions for parts books. It explains the column headings used on parts number pages, including the reference number, part number, description, quantity, serial number range, interchangeability, and remarks. Country codes that may be included are also defined. An example page from the parts book is then shown listing specific part numbers, descriptions, and the book they can be found in.
Kubota l3300 dt gst tractor parts catalogue manualdfjjsjkemmm
This document provides instructions for parts books. It explains the column headings used on parts pages including reference number, part number, description, quantity, serial number range and interchangeability. It also notes country codes that may be included to indicate part differences between countries. The document then provides an example page from a parts book listing parts for an engine crankcase.
Kubota l3130 hst tractor parts catalogue manualdfjjsjkemmm
The document provides instructions for parts books, including definitions of column headings in parts number pages such as reference number, part number, description, quantity, serial number range. It also notes country codes that may be included for parts that differ by country, such as parts working in all countries except France. The document then provides an index of parts for a tractor model broken down by system such as engine, fuel, electrical, transmission, hydraulics, with part numbers and references to parts books.
Kubota l3130 gst tractor parts catalogue manualdfjjsjkemmm
The document provides instructions for parts books, including definitions of column headings in parts number pages such as Reference Number, Part Number, Description, Quantity, Serial Number range, Interchangeability, and Remarks. It also notes country codes that may be included, such as exceptions for parts in other countries like France (FR). Diagrams of product parts are indexed for locating specific components.
Kubota l3130 dt tractor parts catalogue manualdfjjsjkemmm
The document provides instructions for parts books, including definitions of column headings in parts number pages such as reference number, part number, description, quantity, serial number range. It also notes country codes that may be included for parts that differ by country, such as parts working in all countries except France. The document then provides an index of parts for a tractor model broken down by system such as engine, fuel, electrical, transmission, hydraulics, with part numbers and references to parts books.
Kubota l2900 f tractor parts catalogue manualdfjjsjkemmm
This document provides an index and part listings for an L2900F product. It includes sections for the engine, fuel system, cooling water system, electrical system, clutch, transmission, rear axle, brake, front axle, steering, hydraulic system, hood, labels, and accessories. Each section lists the relevant part numbers, descriptions, quantities, and other specifications for the individual components.
Kubota l2900 dt tractor parts catalogue manualdfjjsjkemmm
The crankcase parts list includes over 230 individual parts that make up the crankcase assembly. It lists each part number, description, quantity used, applicable serial number range, interchangeability, remarks, and weight. Key details included are the total weight of the assembled crankcase (48.5kg/106.7lbs) and that most common individual parts like plugs and seals weigh only a few grams.
Kubota l2800 hst tractor parts catalogue manualdfjjsjkemmm
This document provides instructions for using a parts book for a tractor model. It defines the column headings used on parts number pages, including the part reference number, part number, description, quantity, serial number range, interchangeability, and remarks. It also notes country codes that may be included to indicate if a part is different for other countries. The document then provides an index of parts for the tractor model with the part number and relevant parts book for each item.
Kubota l2800 dt tractor parts catalogue manualdfjjsjkemmm
This document provides instructions for using parts books and describes the column headings used on parts number pages. It explains that country codes may be included to indicate if a part is different for other countries. Finally, it lists frequently used parts for a L2800DT/HST tractor, including the part number, description, and reference book for each part.
Kubota l2600 dt tractor parts catalogue manualdfjjsjkemmm
This document provides part numbers and descriptions for a cylinder head. It includes a list of 170 parts with information on the part number, description, quantity used, applicable serial number range, interchangeability, and remarks. It notes country codes that may be relevant for part interchangeability between countries like the US, Canada, France, etc. The total weight of the cylinder head component is provided at the end.
Kubota l2500 f tractor parts catalogue manualdfjjsjkemmm
The document provides instructions and part numbers for a parts book. It lists the column headings used on parts pages including the reference number, part number, description, quantity, serial number range and other details. It then provides an example page from the parts book with over 250 individual part numbers listed for the crankcase component.
Kubota l2500 dt tractor parts catalogue manualdfjjsjkemmm
The document provides instructions for parts books. It defines the column headings used on parts number pages, including reference number, part number, description, quantity, serial number range, interchangeability, and remarks. Country codes are also explained, with symbols indicating the country each part is for (e.g. A for USA, CA for Canada, FR for France). An example page from a parts book is then shown listing parts for an engine crankcase, with the corresponding information for each part.
Kalyan chart DP boss guessing matka results➑➌➋➑➒➎➑➑➊➍
8328958814Satta Matka is a number-based game. There are several markets, each with its owner responsible for releasing the lottery satta Matka market results on time. Kalyan market, Worli market, main Mumbai market, Rajdhani market, and Milan market are some of the main markets or bazaars involved in the satta Matka game. The oldest and most legitimate markets are in Kalyan and Main Mumbai. Every Satta Market has an open and close time. The satta results for these markets are published on or shortly after the open and close times. During the open result, two numbers are decoded, one of which is a three-digit number and the other a single-digit number. Similarly, three-digit and single-digit numbers are declared during the satta market's close. The last digit after adding the three digits of the open or close result is usually the single digit declared during the open and close results.KALYAN MATKA | MATKA RESULT | KALYAN MATKA TIPS | SATTA MATKA | MATKA.COM | MATKA PANA JODI TODAY | BATTA SATKA | MATKA PATTI JODI NUMBER | MATKA RESULTS | MATKA CHART | MATKA JODI | SATTA COM | FULL RATE GAME | MATKA GAME | MATKA WAPKA | ALL MATKA RESULT LIVE ONLINE | MATKA RESULT | KALYAN MATKA RESULT | DPBOSS MATKA 143 | MAINSATTA MATKA SATTA FAST RESULT KALYAN TOP MATKA RESULT KALYAN SATTA MATKA FAST RESULT MILAN RATAN RAJDHANI MAIN BAZAR MATKA FAST TIPS RESULT MATKA CHART JODI CHART PANEL CHART FREE FIX GAME SATTAMATKA ! MATKA MOBI SATTA 143 spboss.in TOP NO1 RESULT FULL RATE MATKA ONLINE GAME PLAY BY APP SPBOSSdp boss net, dp satta, dpboss dpboss, indian satta matka, kalyan matkà result today , matka boss, matka result live, matka satta result today, satamatka com, satta boss, satta matka king, sattamatkà, sattamatkà result, sattamatta com, sattmatka sattmatka, star matka, tara matka, tara satta matka, worli matka, indian matka, matka live, kalyan guessing, satta fix, kalyan final ank, dp matka, dpboss net, sata mata com, सट्टा मटका, sattamatkà 143, golden matka, satta matta matka 143, satta fast, kalyan open, satta 143, dpboss 143 guessing, dpboss satta, golden satta matka, satta bajar
Satta Matka Market is India's leading website providing the quickest sattamatka outcome, experienced in Satta Matka game. Our services include free Satta Matka Trick and Tips for Kalyan Matka and Disawar Satta King, as well as satta matka graphs, online play, tips and more. Our team of experts strive to help you recoup your losses quickly through our proposals such as Free Satta Matka Tips and Kalyan Bazar Tips. We are known as India's best Matka DpBoss portal site, here to deliver updates on all sorts of Satta Market like Kalyan Bazar, Milan, Rajdhani, Time Bazaar, Main and the most current charts. Stay tuned with us for more live updates on the Satta market
Automotive Engine Valve Manufacturing Plant Project Report.pptxSmith Anderson
The report provides a complete roadmap for setting up an Automotive Engine Valve. It covers a comprehensive market overview to micro-level information such as unit operations involved, raw material requirements, utility requirements, infrastructure requirements, machinery and technology requirements, manpower requirements, packaging requirements, transportation requirements, etc.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR BWH
Configuration: 312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01567260
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Always wear protective gloves when handling parts that have been
heated.
1. Perform the following procedure, if the ring gear was removed from the flywheel:
a. Heat the ring gear to 150 °C (302 °F) in an oven.
1/3
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. b. Press the ring gear onto the flywheel.
Note: Prior to the installation of the flywheel, refer to Specifications, "Flywheel" for
information on checking the flywheel assembly for flatness.
Illustration 1 g00605504
2. Install Tool (A), a strap, and a suitable lifting device onto flywheel (6) .
3. Install flywheel (6). The weight of the flywheel is 50 kg (110 lb).
Illustration 2 g00605501
4. Install six bolts (5) in order to secure flywheel (6) onto the crankshaft. Tighten the bolts to a
torque of 83 ± 5 N·m (61 ± 4 lb ft).
5. Remove Tool (A) from the flywheel.
2/3
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g00605497
6. Place the inner ring (4) in position on the flywheel.
7. Install four socket head bolts (3) in order to secure the inner ring (4) to the flywheel.
Illustration 4 g00605492
8. Place the adapter (2) in position on the flywheel housing.
9. Install twelve bolts and washers (1) in order to secure the adapter (2) on the flywheel
housing.
10. Check the flywheel runout. Refer to Testing and Adjusting, "Flywheel Housing - Inspect"
for more information on flywheel runout.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon May 18 23:09:21 UTC+0800 2020
3/3
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR BWH
Configuration: 312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01135944
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
B
5P-7312 Seal Distorter 1
5P-7338 Distorter Ring 2
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
1/3
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00604840
Note: If the oil seal shows a sign of oil leaks, remove the wear sleeve and the oil seal.
1. Drill three evenly spaced 3 mm (0.12 inch) holes in crankshaft rear seal (1).
2. Use Tool (A) to remove the crankshaft rear seal.
Illustration 2 g00604844
3. Use Tool (B) to remove the wear sleeve (2) (not shown) from the rear of the crankshaft.
Note: When you are removing the wear sleeve, take extreme care not to damage the
crankshaft.
2/3
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR BWH
Configuration: 312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615317
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
9U-6169 Installer 1
9U-6171 Locator 1
9U-6172 Bolt 2
5P-8247 Hard Washer 1
6V-3303 Bolt 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. To install a new wear sleeve that is complete with a seal, use 169-5464 Quick Cure Primer
to clean the outer diameter of the crankshaft and the inside diameter of the wear sleeve.
Apply 4C-9507 Retaining Compound to the faces of all the mating parts.
1/3
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 1 g00604874
2. Install a new wear sleeve that is complete with a seal (1) (not shown) with Tool (A), as
follows:
Illustration 2 g00604875
a. Install 9U-6171 Locator (3) onto the crankshaft with 9U-6172 Bolt (4).
b. Put the new wear sleeve that is complete with a seal in 9U-6169 Installer (2).
c. Put 6V-3303 Bolt (6) through 5P-8247 Hard Washer (5) and 9U-6169 Installer (2)
and thread into 9U-6171 Locator (3).
d. Push the wear sleeve that is complete with a seal onto the crankshaft until 9U-6169
Installer (2) bottoms out.
2/3
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 3 g00604874
e. Remove Tool (A) and check crankshaft rear seal (1) (not shown) for correct
installation.
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon May 18 23:11:20 UTC+0800 2020
3/3
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR BWH
Configuration: 312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i05421135
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
B 1P-0510 Driver Group 1
Start By:
A. Remove the electric starting motor.
B. Remove the flywheel and ring gear.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 1 g00605593
1. Install Tooling (A) , a strap, and a suitable lifting device onto flywheel housing (2) .
2. Remove bolts (1) and the washers that secure flywheel housing (2) to the cylinder block.
Note: Identify the four shorter bolts for later installation into the flywheel housing.
3. Remove flywheel housing (2) . The weight of the flywheel is approximately.29 kg (65 lb).
4. Check oil seal (3) for serviceability. If necessary, replace the oil seal and crankshaft wear
sleeve.
Illustration 2 g00605601
5. Use Tooling (B) in order to remove the oil seal (3) (not shown).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
2/3
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. B 9U-6170 Installer Gp 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 3 g00605593
1. Clean old gasket material (4) from the mating surfaces of the cylinder block and the
flywheel housing. Install a new gasket on the cylinder block.
2. Place flywheel housing (2) in position on the cylinder block.
3. Install the washers and bolts (1) in order to secure flywheel housing (2) to the cylinder
block.
4. Use Tooling (B) in order to install the oil seal (3) , and the crankshaft wear sleeve (not
shown).
End By:
a. Install the flywheel.
b. Install the electric starting motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon May 18 23:12:19 UTC+0800 2020
3/3
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR BWH
Configuration: 312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01578488
Crankshaft Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2321 Combination Puller 1
B 6V-9120 Socket (1)
1
( 1 )
Tool (B) is a 46 mm socket.
Start By:
A. Remove the V-belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 1 g00604778
1. Use Tool (B) to remove nut (1) and washer (2) from the threaded end of the crankshaft.
Illustration 2 g00604784
2. Use Tool (A) to remove crankshaft pulley (3) from the engine.
2/4
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 3 g00604792
3. If it is necessary to remove the wear sleeve (4) from the crankshaft pulley (3), use a hammer
and a chisel. Hold the chisel at right angles to the surface of the wear sleeve. Tap the wear
sleeve in three places. You can remove the wear sleeve once the tension is released.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 4 g00604778
3/4
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. 1. Put crankshaft pulley (3) in position on the engine.
2. Install washer (2) and nut (1). Use Tool (B) to tighten nut (1) to a torque of 490 ± 10 N·m
(361 ± 7 lb ft).
End By: Install the V-belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon May 18 23:13:19 UTC+0800 2020
4/4
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR BWH
Configuration: 312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01131366
Crankshaft Front Seal - Remove
SMCS - 1160-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
Start By:
A. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/2
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00529162
1. Drill three evenly spaced 3 mm (0.12 inch) holes in crankshaft front seal (1) .
2. Use Tool (A) and remove crankshaft front seal (1). Remove the seal evenly by alternating
the position of Tool (A) from hole to hole.
Note: Do not damage the flange of the crankshaft during the removal process for the
crankshaft front seal.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon May 18 23:14:18 UTC+0800 2020
2/2
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR BWH
Configuration: 312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i02080454
Crankshaft Front Seal - Install
SMCS - 1160-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6180 Front Seal Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 1 g00612743
1. Clean the faces of all the mating parts. Apply a thin coat of clean engine oil to a new
crankshaft front seal.
2. Install new crankshaft front seal (1) in the front housing with Tool (A) .
3. Remove Tooling (A) and check crankshaft front seal (1) for correct installation.
4. Apply clean engine oil to the face of the crankshaft pulley that will be in contact with the
new crankshaft front seal.
End By: Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon May 18 23:15:17 UTC+0800 2020
2/2
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR BWH
Configuration: 312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615339
Gear Group (Front) - Remove - Idler Gear Only
SMCS - 1206-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6148 Idler Shaft Puller 1
B 1P-0510 Driver Group 1
Start By:
A. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
1/5
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Note: Before removal, ensure that the marks on the timing gears are in alignment. Align the
fuel injection drive gear with the "33" mark with the "3" mark on the idler gear. Make an
alignment of the "2" mark on the camshaft gear with the "22" mark on the idler gear. Align
the "1" mark on the crankshaft gear with the "11" mark on the idler gear. The No. 1 cylinder
is at the top center position when these marks are in alignment.
Illustration 1 g00611568
1. Remove idler gear bolt (1) and the washer from the idler gear shaft .
2. Remove thrust plate (2) from the idler gear shaft.
2/5
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 2 g00611569
3. Remove idler gear (3) from the idler gear shaft.
Illustration 3 g00611570
4. If necessary, use Tool (B) to remove bushing (4) (not shown) from idler gear (3) .
Illustration 4 g00611572
3/5
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Illustration 5 g00611573
5. The following items are components of Tool (A) .
◦ 9U-6147 Stud (6)
◦ 6V-8231 Nut (7)
◦ 9U-6146 Sleeve Assembly (8)
◦ 8T-4244 Nut (9)
6. Use Tool (A) and remove idler shaft (5) from the cylinder block. Check the idler shaft for
wear and damage. Replace the shaft, if necessary.
Note: See the following list for the removal of the other gears in the front gear group.
• In order to remove the camshaft gear, refer to Disassembly and Assembly, "Camshaft -
Remove".
• In order to remove the fuel injection pump gear, refer to Disassembly and Assembly, "Fuel
Injection Pump - Remove".
• In order to remove the gear from the engine oil pump, refer to Disassembly and Assembly,
"Engine Oil Pump - Remove".
• In order to remove the crankshaft gear, refer to Disassembly and Assembly, "Crankshaft
Gear - Remove and Install".
4/5
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR BWH
Configuration: 312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615420
Gear Group (Front) - Install - Idler Gear Only
SMCS - 1206-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 1 g00611570
1. Use Tool (A) to install a new bushing (4) (not shown), if the bushing was removed.
Illustration 2 g00611572
2. Install idler shaft (5) onto the cylinder block.
Note: When the idler shaft is installed, ensure that the oil hole of the shaft is up. If
necessary, cool the idler shaft to 0 °C (32 °F) before installation. The temperature of the
idler shaft is lowered in order to ease the installation of the idler shaft.
Illustration 3 g00611569
Note: Ensure that the marks on the timing gears are in alignment. Align the fuel injection
drive gear with the "33" mark with the "3" mark on idler gear. Make an alignment of the "2"
mark on the camshaft gear with the "22" mark on the idler gear. Align the "1" mark on the
crankshaft gear with the "11" mark on the idler gear. The No. 1 cylinder is at the top center
position when these marks are in alignment.
3. Install idler gear (3) onto the idler shaft.
2/3
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...