The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. The procedures include:
1) Removing the electric starting motor and flywheel first.
2) Using lifting tools to remove the housing bolts and housing.
3) Inspecting and replacing the dowels and gasket if needed.
4) Cleaning the mating surfaces and installing the new gasket on the cylinder block.
5) Placing the housing back in position and securing it with bolts.
Caterpillar cat 312 d l excavator (prefix phh) service repair manual (phh0000...pfiskdmjekm
The document provides instructions for removing and installing the flywheel housing on a Caterpillar C4.2 engine. The summary is:
1) To remove the flywheel housing, first remove the electric starting motor and flywheel. Then use lifting tools to remove the housing bolts and housing.
2) To install the flywheel housing, first install a new oil seal and check the dowels. Clean the mating surfaces and install a new gasket on the cylinder block. Place the housing in position and install the bolts to secure it.
3) The document also provides instructions for removing the flywheel, crankshaft rear seal, and installing the rear seal.
Caterpillar cat 312 d l excavator (prefix rkf) service repair manual (rkf0000...pfiskdmjekm
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. To remove the housing, technicians must first remove the electric starting motor and flywheel. They use lifting tools to detach the housing from the cylinder block, then extract the oil seal. For installation, they clean surfaces, fit a new gasket and oil seal, and secure the housing with bolts, reinstalling other parts in the reverse order of removal.
Caterpillar cat 312 d l excavator (prefix ska) service repair manual (ska0000...pfiskdmjekm
- The document provides instructions for removing and installing a flywheel, flywheel housing, and crankshaft rear seal on a Caterpillar 312D L excavator.
- It describes the required tools and multi-step procedures, which include removing bolts, brackets, and other components to access the parts. Special care must be taken to avoid damage and contain fluids.
- The installation procedures describe cleaning and applying compounds to mating parts, using installing tools and levers to correctly position the new parts, and reinstalling other removed components once complete.
Caterpillar cat 312 d excavator (prefix kes) service repair manual (kes00001 ...fksjksmmde
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312D excavator with a C4.2 engine. It describes how to remove the electric starting motor, flywheel, ring gear, and housing bolts. It then explains how to install the housing using a link bracket and driver group, and reinstall the flywheel and starting motor.
Caterpillar cat 336 d2 l excavator (prefix far) service repair manual (far000...pfiskdmjekm
The document provides instructions for assembling and installing a swivel on an excavator. It lists the required tools which include link brackets and vacuum caps. The procedure involves cleaning parts, positioning the swivel using lifting devices, installing O-rings and seals, attaching hoses and fittings, and tightening bolts to specified torques. Proper cleanliness is emphasized to prevent contamination which can cause premature wear.
Caterpillar cat 312 c excavator (prefix bwh) service repair manual (bwh00001 ...fjskkksmemm
The document provides instructions for removing and installing a crankshaft pulley on a 312C excavator. The removal procedure involves using a puller tool to remove the pulley from the crankshaft. For installation, the pulley is pressed onto the crankshaft and secured with bolts that are tightened to the specified torque.
Caterpillar cat 314 d cr excavator (prefix xhr) service repair manual (xhr000...soeldksejdksem
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It outlines the required tools and step-by-step procedures. To remove the housing, the electric starting motor and flywheel must first be removed. Various bolts and brackets are then removed to access the housing, which can be lifted out. Reinstallation follows the reverse order.
Caterpillar cat 312 d excavator (prefix phh) service repair manual (phh00001 ...fksjksmmde
The document provides instructions for removing and installing the flywheel housing on a Caterpillar C4.2 engine. The summary is:
1) To remove the flywheel housing, first remove the electric starting motor and flywheel. Then use lifting tools to remove the housing bolts and housing.
2) To install the flywheel housing, first install a new oil seal and check the dowels. Clean the mating surfaces and install a new gasket on the cylinder block. Place the housing in position and install the bolts to secure it.
3) The document also provides instructions for removing the flywheel, crankshaft rear seal, and installing the rear seal.
Caterpillar cat 312 d l excavator (prefix phh) service repair manual (phh0000...pfiskdmjekm
The document provides instructions for removing and installing the flywheel housing on a Caterpillar C4.2 engine. The summary is:
1) To remove the flywheel housing, first remove the electric starting motor and flywheel. Then use lifting tools to remove the housing bolts and housing.
2) To install the flywheel housing, first install a new oil seal and check the dowels. Clean the mating surfaces and install a new gasket on the cylinder block. Place the housing in position and install the bolts to secure it.
3) The document also provides instructions for removing the flywheel, crankshaft rear seal, and installing the rear seal.
Caterpillar cat 312 d l excavator (prefix rkf) service repair manual (rkf0000...pfiskdmjekm
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. To remove the housing, technicians must first remove the electric starting motor and flywheel. They use lifting tools to detach the housing from the cylinder block, then extract the oil seal. For installation, they clean surfaces, fit a new gasket and oil seal, and secure the housing with bolts, reinstalling other parts in the reverse order of removal.
Caterpillar cat 312 d l excavator (prefix ska) service repair manual (ska0000...pfiskdmjekm
- The document provides instructions for removing and installing a flywheel, flywheel housing, and crankshaft rear seal on a Caterpillar 312D L excavator.
- It describes the required tools and multi-step procedures, which include removing bolts, brackets, and other components to access the parts. Special care must be taken to avoid damage and contain fluids.
- The installation procedures describe cleaning and applying compounds to mating parts, using installing tools and levers to correctly position the new parts, and reinstalling other removed components once complete.
Caterpillar cat 312 d excavator (prefix kes) service repair manual (kes00001 ...fksjksmmde
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312D excavator with a C4.2 engine. It describes how to remove the electric starting motor, flywheel, ring gear, and housing bolts. It then explains how to install the housing using a link bracket and driver group, and reinstall the flywheel and starting motor.
Caterpillar cat 336 d2 l excavator (prefix far) service repair manual (far000...pfiskdmjekm
The document provides instructions for assembling and installing a swivel on an excavator. It lists the required tools which include link brackets and vacuum caps. The procedure involves cleaning parts, positioning the swivel using lifting devices, installing O-rings and seals, attaching hoses and fittings, and tightening bolts to specified torques. Proper cleanliness is emphasized to prevent contamination which can cause premature wear.
Caterpillar cat 312 c excavator (prefix bwh) service repair manual (bwh00001 ...fjskkksmemm
The document provides instructions for removing and installing a crankshaft pulley on a 312C excavator. The removal procedure involves using a puller tool to remove the pulley from the crankshaft. For installation, the pulley is pressed onto the crankshaft and secured with bolts that are tightened to the specified torque.
Caterpillar cat 314 d cr excavator (prefix xhr) service repair manual (xhr000...soeldksejdksem
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It outlines the required tools and step-by-step procedures. To remove the housing, the electric starting motor and flywheel must first be removed. Various bolts and brackets are then removed to access the housing, which can be lifted out. Reinstallation follows the reverse order.
Caterpillar cat 312 d excavator (prefix phh) service repair manual (phh00001 ...fksjksmmde
The document provides instructions for removing and installing the flywheel housing on a Caterpillar C4.2 engine. The summary is:
1) To remove the flywheel housing, first remove the electric starting motor and flywheel. Then use lifting tools to remove the housing bolts and housing.
2) To install the flywheel housing, first install a new oil seal and check the dowels. Clean the mating surfaces and install a new gasket on the cylinder block. Place the housing in position and install the bolts to secure it.
3) The document also provides instructions for removing the flywheel, crankshaft rear seal, and installing the rear seal.
Caterpillar cat 312 d l excavator (prefix phh) service repair manual (phh0000...fjjskekdmmem
This document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. The removal procedure involves taking out the electric starting motor, flywheel, and ring gear. Tools are required to secure the flywheel housing during removal. Reinstallation involves reversing the removal steps and checking flywheel runout.
The document provides instructions for removing and installing the flywheel housing on a Caterpillar C4.2 engine. The removal procedure involves using lifting tools to remove the housing, which weighs approximately 29 kg. The oil seal is also removed using driver tools. For installation, a new gasket and oil seal are used, and the housing is secured with bolts after being placed into position. The instructions are part of a service manual for Caterpillar 312D excavators.
The document provides instructions for removing and installing the flywheel housing on a Caterpillar C4.2 engine. The removal procedure involves using lifting tools to remove the housing, which weighs approximately 29 kg. The oil seal is also removed using driver tools. For installation, a new gasket is used and the housing is secured with bolts after checking dowel pins and installing the new oil seal. The flywheel and starting motor must then be reinstalled.
This document provides instructions for removing and installing the flywheel housing on a Caterpillar C4.2 engine. The procedure involves using lifting equipment to remove the housing, which weighs approximately 29 kg. A new gasket must be installed and the housing bolted back into place. Special tools are required to remove and install the oil seal in the housing.
Caterpillar cat 312 d l excavator (prefix rkf) service repair manual (rkf0000...fjjskmdmem
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes:
- Removing the electric starting motor and flywheel
- Using a link bracket and driver group to remove the flywheel housing
- Checking the flywheel housing for cracks or damage and replacing as needed
- Reinstalling the flywheel and starting motor along with any gaskets or seals
The summary covers the key steps and tools involved in the flywheel housing removal and installation process according to the technical document.
Caterpillar cat 312 d l excavator (prefix rkf) service repair manual (rkf0000...fhjsjkdmemm
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the housing.
2) Using lifting tools to remove housing bolts and lift the housing off the engine block.
3) Removing the oil seal from the housing using driver tools.
4) Cleaning surfaces and installing a new gasket before positioning the housing and torquing bolts to secure it.
Caterpillar cat 312 d excavator (prefix rkf) service repair manual (rkf00001 ...fjskekxcddmmme
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes:
- Removing the electric starting motor and flywheel
- Using a link bracket and lifting device to remove the flywheel housing
- Checking the flywheel housing for cracks or damage before reinstalling with new seals and gaskets
Caterpillar cat 312 d excavator (prefix rkf) service repair manual (rkf00001 ...dueikdkmem
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the housing.
2) Using lifting tools to remove housing bolts and lift the housing off the engine block.
3) Removing the oil seal from the housing using driver tools.
4) Cleaning surfaces and installing a new gasket before positioning the housing and torquing bolts to secure it.
Caterpillar cat 312 d excavator (prefix rkf) service repair manual (rkf00001 ...cdfzxs
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove the flywheel housing bolts and separate the housing from the cylinder block.
3) Installing a new gasket and replacing the oil seal before reinstalling the flywheel housing with new bolts and washers.
4) Reinstalling the flywheel, electric starting motor after installing the flywheel housing.
Caterpillar cat 312 d excavator (prefix kes) service repair manual (kes00001 ...cdfzxs
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes how to remove the electric starting motor and flywheel first. Then it explains how to use a link bracket and driver group to remove the flywheel housing. Proper cleaning of parts is emphasized to prevent contamination.
Bomag bw 154 ad tandem rollers service repair manualfhjsjkdmemm
This document provides technical data and adjustment values for Tandem Rollers including the BW 141 AD, BW 154 AD, and BW 154 AD AM. It includes specifications for the Deutz diesel engine like power output, idle speeds, and valve clearances. It also lists components of the travel, vibration, and steering systems along with their types, displacement volumes, pressure settings, and other parameters. Filling capacities are provided for engine oil, hydraulic oil, and other fluids.
Bomag bw 154 ac 4 tandem rollers service repair manualfhjsjkdmemm
The document provides technical specifications and adjustment values for Tandem Rollers models BW 141 AD Serie 4 and BW 154 AD Serie 4. It includes details on the engine, travel pump, travel motors, drum reduction gear, vibration pump, vibration motor, steering and charge pump, and filling capacities. The specifications are broken out by component and include information like component type, system, displacement, pressure levels, speeds, ratios, and approved lubricants.
Bomag bw 151 ad 4 tandem rollers service repair manualfhjsjkdmemm
This document provides operating and maintenance instructions for BOMAG tandem vibratory rollers, models BW 141 AD-4, BW 151 AD-4, BW 151 AC-4, and BW 161 ADCV. It includes sections on safety regulations, controls and indicators, operation, maintenance, and troubleshooting. The safety section emphasizes that the machine must only be used for its intended purposes of compacting asphalt and soil and stresses the importance of following all safety instructions.
Bomag bw 151 ad tandem rollers service repair manualfhjsjkdmemm
This document provides technical data and adjustment values for Tandem Rollers including the BW 141 AD, BW 154 AD, and BW 154 AD AM. It includes specifications for the Deutz diesel engine like power output, idle speeds, and valve clearances. It also lists components of the travel, vibration, and steering systems along with their types, displacement volumes, pressure settings, and other parameters. Filling capacities are provided for engine oil, hydraulic oil, and other fluids.
Bomag bw 151 ac 4 tandem rollers service repair manualfhjsjkdmemm
This document provides operating and maintenance instructions for BOMAG tandem vibratory rollers, models BW 141 AD-4, BW 151 AD-4, BW 151 AC-4, and BW 161 ADCV. It includes sections on safety regulations, controls and indicators, operation, maintenance, and troubleshooting. The safety section emphasizes that the machine must only be used for its intended purposes of compacting asphalt and soil and stresses the importance of following all safety instructions.
Bomag bw 141 ad 4 tandem rollers service repair manualfhjsjkdmemm
This document provides operating and maintenance instructions for BOMAG tandem vibratory rollers, models BW 141 AD-4, BW 151 AD-4, BW 151 AC-4, and BW 161 ADCV. It includes sections on safety regulations, controls and indicators, operation, maintenance, and troubleshooting. The technical data section specifies the dimensions, weights, engine, and other technical specifications for each roller model.
Bomag bw 141 ad tandem rollers service repair manualfhjsjkdmemm
This document provides technical data and adjustment values for Tandem Rollers including the BW 141 AD, BW 154 AD, and BW 154 AD AM. It includes specifications for the Deutz diesel engine like power output, idle speeds, and valve clearances. It also lists components of the travel, vibration, and steering systems along with their types, displacement volumes, pressure settings, and other parameters. Filling capacities are provided for engine oil, hydraulic oil, and other fluids.
Bomag bw 141 ac 4 tandem rollers service repair manualfhjsjkdmemm
This document provides technical data and adjustment values for Tandem Rollers including the BW 141 AD Serie 4, BW 154 AD Serie 4, and BW 154 AD AM Serie 4. It includes specifications for the Deutz diesel engine, travel pump and motors, vibration pump and motors, steering pump, and filling capacities. The data is presented in a table format with specifications such as engine power, pump displacement volumes, pressure settings, and fluid capacities.
Bomag bw 135 ad single tandem vibratory roller service repair manualfhjsjkdmemm
This document provides operating and maintenance instructions for BOMAG tandem vibratory rollers. It includes technical specifications, safety regulations, descriptions of indicators and controls, operating instructions, maintenance instructions, and troubleshooting information. Safety is emphasized, including intended and prohibited uses of the machines, and potential hazards are outlined.
Hyundai r170 w 7a wheel excavator service repair manualfhjsjkdmemm
The document provides instructions for removing and installing a swing motor, disassembling and assembling the swing motor, removing and installing a reduction gear, and disassembling and assembling the reduction gear of an excavator. The summary is as follows:
1. The removal and installation instructions for the swing motor include disconnecting hoses and mounting bolts, and removing the swing motor assembly. Installation is the reverse of removal.
2. Disassembling the swing motor involves removing components like the valve, casing, piston, and shaft. Assembly is the reverse of disassembly.
3. Removal and installation of the reduction gear involves slinging and removing/installing mounting bolts.
Caterpillar cat 336 f excavator (prefix dsw) service repair manual (dsw00001 ...fhjsjkdmemm
This document provides instructions for disassembling the travel motor on 336F and 336F L excavator models. It outlines 27 steps to fully disassemble the travel motor, including removing the motor head assembly, piston assemblies, barrel assembly, friction plates, seals, springs, and other internal components. Detailed illustrations are provided to identify each part mentioned in the procedure. Safety precautions are noted throughout to warn of potential spring forces or fluid containment. The goal is to break down the travel motor into its core components while maintaining the correct orientation of parts for reassembly.
Caterpillar cat 336 d2 l excavator (prefix ycf) service repair manual (ycf000...fhjsjkdmemm
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other internal components. Safety warnings are provided to prevent injury from spring forces.
More Related Content
Similar to Caterpillar cat 312 d l excavator (prefix phh) service repair manual (phh00001 and up)
Caterpillar cat 312 d l excavator (prefix phh) service repair manual (phh0000...fjjskekdmmem
This document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. The removal procedure involves taking out the electric starting motor, flywheel, and ring gear. Tools are required to secure the flywheel housing during removal. Reinstallation involves reversing the removal steps and checking flywheel runout.
The document provides instructions for removing and installing the flywheel housing on a Caterpillar C4.2 engine. The removal procedure involves using lifting tools to remove the housing, which weighs approximately 29 kg. The oil seal is also removed using driver tools. For installation, a new gasket and oil seal are used, and the housing is secured with bolts after being placed into position. The instructions are part of a service manual for Caterpillar 312D excavators.
The document provides instructions for removing and installing the flywheel housing on a Caterpillar C4.2 engine. The removal procedure involves using lifting tools to remove the housing, which weighs approximately 29 kg. The oil seal is also removed using driver tools. For installation, a new gasket is used and the housing is secured with bolts after checking dowel pins and installing the new oil seal. The flywheel and starting motor must then be reinstalled.
This document provides instructions for removing and installing the flywheel housing on a Caterpillar C4.2 engine. The procedure involves using lifting equipment to remove the housing, which weighs approximately 29 kg. A new gasket must be installed and the housing bolted back into place. Special tools are required to remove and install the oil seal in the housing.
Caterpillar cat 312 d l excavator (prefix rkf) service repair manual (rkf0000...fjjskmdmem
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes:
- Removing the electric starting motor and flywheel
- Using a link bracket and driver group to remove the flywheel housing
- Checking the flywheel housing for cracks or damage and replacing as needed
- Reinstalling the flywheel and starting motor along with any gaskets or seals
The summary covers the key steps and tools involved in the flywheel housing removal and installation process according to the technical document.
Caterpillar cat 312 d l excavator (prefix rkf) service repair manual (rkf0000...fhjsjkdmemm
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the housing.
2) Using lifting tools to remove housing bolts and lift the housing off the engine block.
3) Removing the oil seal from the housing using driver tools.
4) Cleaning surfaces and installing a new gasket before positioning the housing and torquing bolts to secure it.
Caterpillar cat 312 d excavator (prefix rkf) service repair manual (rkf00001 ...fjskekxcddmmme
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes:
- Removing the electric starting motor and flywheel
- Using a link bracket and lifting device to remove the flywheel housing
- Checking the flywheel housing for cracks or damage before reinstalling with new seals and gaskets
Caterpillar cat 312 d excavator (prefix rkf) service repair manual (rkf00001 ...dueikdkmem
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the housing.
2) Using lifting tools to remove housing bolts and lift the housing off the engine block.
3) Removing the oil seal from the housing using driver tools.
4) Cleaning surfaces and installing a new gasket before positioning the housing and torquing bolts to secure it.
Caterpillar cat 312 d excavator (prefix rkf) service repair manual (rkf00001 ...cdfzxs
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove the flywheel housing bolts and separate the housing from the cylinder block.
3) Installing a new gasket and replacing the oil seal before reinstalling the flywheel housing with new bolts and washers.
4) Reinstalling the flywheel, electric starting motor after installing the flywheel housing.
Caterpillar cat 312 d excavator (prefix kes) service repair manual (kes00001 ...cdfzxs
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes how to remove the electric starting motor and flywheel first. Then it explains how to use a link bracket and driver group to remove the flywheel housing. Proper cleaning of parts is emphasized to prevent contamination.
Similar to Caterpillar cat 312 d l excavator (prefix phh) service repair manual (phh00001 and up) (10)
Bomag bw 154 ad tandem rollers service repair manualfhjsjkdmemm
This document provides technical data and adjustment values for Tandem Rollers including the BW 141 AD, BW 154 AD, and BW 154 AD AM. It includes specifications for the Deutz diesel engine like power output, idle speeds, and valve clearances. It also lists components of the travel, vibration, and steering systems along with their types, displacement volumes, pressure settings, and other parameters. Filling capacities are provided for engine oil, hydraulic oil, and other fluids.
Bomag bw 154 ac 4 tandem rollers service repair manualfhjsjkdmemm
The document provides technical specifications and adjustment values for Tandem Rollers models BW 141 AD Serie 4 and BW 154 AD Serie 4. It includes details on the engine, travel pump, travel motors, drum reduction gear, vibration pump, vibration motor, steering and charge pump, and filling capacities. The specifications are broken out by component and include information like component type, system, displacement, pressure levels, speeds, ratios, and approved lubricants.
Bomag bw 151 ad 4 tandem rollers service repair manualfhjsjkdmemm
This document provides operating and maintenance instructions for BOMAG tandem vibratory rollers, models BW 141 AD-4, BW 151 AD-4, BW 151 AC-4, and BW 161 ADCV. It includes sections on safety regulations, controls and indicators, operation, maintenance, and troubleshooting. The safety section emphasizes that the machine must only be used for its intended purposes of compacting asphalt and soil and stresses the importance of following all safety instructions.
Bomag bw 151 ad tandem rollers service repair manualfhjsjkdmemm
This document provides technical data and adjustment values for Tandem Rollers including the BW 141 AD, BW 154 AD, and BW 154 AD AM. It includes specifications for the Deutz diesel engine like power output, idle speeds, and valve clearances. It also lists components of the travel, vibration, and steering systems along with their types, displacement volumes, pressure settings, and other parameters. Filling capacities are provided for engine oil, hydraulic oil, and other fluids.
Bomag bw 151 ac 4 tandem rollers service repair manualfhjsjkdmemm
This document provides operating and maintenance instructions for BOMAG tandem vibratory rollers, models BW 141 AD-4, BW 151 AD-4, BW 151 AC-4, and BW 161 ADCV. It includes sections on safety regulations, controls and indicators, operation, maintenance, and troubleshooting. The safety section emphasizes that the machine must only be used for its intended purposes of compacting asphalt and soil and stresses the importance of following all safety instructions.
Bomag bw 141 ad 4 tandem rollers service repair manualfhjsjkdmemm
This document provides operating and maintenance instructions for BOMAG tandem vibratory rollers, models BW 141 AD-4, BW 151 AD-4, BW 151 AC-4, and BW 161 ADCV. It includes sections on safety regulations, controls and indicators, operation, maintenance, and troubleshooting. The technical data section specifies the dimensions, weights, engine, and other technical specifications for each roller model.
Bomag bw 141 ad tandem rollers service repair manualfhjsjkdmemm
This document provides technical data and adjustment values for Tandem Rollers including the BW 141 AD, BW 154 AD, and BW 154 AD AM. It includes specifications for the Deutz diesel engine like power output, idle speeds, and valve clearances. It also lists components of the travel, vibration, and steering systems along with their types, displacement volumes, pressure settings, and other parameters. Filling capacities are provided for engine oil, hydraulic oil, and other fluids.
Bomag bw 141 ac 4 tandem rollers service repair manualfhjsjkdmemm
This document provides technical data and adjustment values for Tandem Rollers including the BW 141 AD Serie 4, BW 154 AD Serie 4, and BW 154 AD AM Serie 4. It includes specifications for the Deutz diesel engine, travel pump and motors, vibration pump and motors, steering pump, and filling capacities. The data is presented in a table format with specifications such as engine power, pump displacement volumes, pressure settings, and fluid capacities.
Bomag bw 135 ad single tandem vibratory roller service repair manualfhjsjkdmemm
This document provides operating and maintenance instructions for BOMAG tandem vibratory rollers. It includes technical specifications, safety regulations, descriptions of indicators and controls, operating instructions, maintenance instructions, and troubleshooting information. Safety is emphasized, including intended and prohibited uses of the machines, and potential hazards are outlined.
Hyundai r170 w 7a wheel excavator service repair manualfhjsjkdmemm
The document provides instructions for removing and installing a swing motor, disassembling and assembling the swing motor, removing and installing a reduction gear, and disassembling and assembling the reduction gear of an excavator. The summary is as follows:
1. The removal and installation instructions for the swing motor include disconnecting hoses and mounting bolts, and removing the swing motor assembly. Installation is the reverse of removal.
2. Disassembling the swing motor involves removing components like the valve, casing, piston, and shaft. Assembly is the reverse of disassembly.
3. Removal and installation of the reduction gear involves slinging and removing/installing mounting bolts.
Caterpillar cat 336 f excavator (prefix dsw) service repair manual (dsw00001 ...fhjsjkdmemm
This document provides instructions for disassembling the travel motor on 336F and 336F L excavator models. It outlines 27 steps to fully disassemble the travel motor, including removing the motor head assembly, piston assemblies, barrel assembly, friction plates, seals, springs, and other internal components. Detailed illustrations are provided to identify each part mentioned in the procedure. Safety precautions are noted throughout to warn of potential spring forces or fluid containment. The goal is to break down the travel motor into its core components while maintaining the correct orientation of parts for reassembly.
Caterpillar cat 336 d2 l excavator (prefix ycf) service repair manual (ycf000...fhjsjkdmemm
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other internal components. Safety warnings are provided to prevent injury from spring forces.
Caterpillar cat 336 d2 l excavator (prefix xbh) service repair manual (xbh000...fhjsjkdmemm
The document provides instructions for installing a swivel on an excavator. It describes using lifting devices and tools to position the swivel. O-rings and seals are installed on the swivel housing and rotor before assembling them together. Bolts are used to secure the parts and the swivel is tested for leaks by applying air pressure. Finally, hoses and fittings are reconnected to complete the installation.
Caterpillar cat 336 d2 l excavator (prefix wdc) service repair manual (wdc000...fhjsjkdmemm
The document provides instructions for assembling a piston motor. It details 17 steps to install various parts like bearings, seals, springs, and retaining rings. Safety precautions are included to properly handle parts under spring tension. The assembly ends by installing the head and bolts.
Caterpillar cat 336 d2 l excavator (prefix wbc) service repair manual (wbc000...fhjsjkdmemm
The document provides instructions for removing and installing various engine components, including:
- Valve guides are removed from the cylinder head using a valve guide driver tool. New guides are installed using driver tools until the proper height is reached.
- Valve seat inserts are removed from the cylinder head using extractors. New inserts are installed using a driver tool after being cooled.
- The engine oil filter base, oil filter, and oil cooler are removed. Hoses are disconnected and bolts removed to access these components.
Caterpillar cat 336 d2 l excavator (prefix tly) service repair manual (tly000...fhjsjkdmemm
1. The document provides instructions for disassembling and assembling the piston pump of a 336D2 excavator.
2. The disassembly process involves removing 27 individual parts in a specific order, taking care with spring-loaded components.
3. Reassembly requires installing the parts in the reverse order, with some components requiring special tools or heating/cooling during installation. Proper end play must be verified during assembly.
Caterpillar cat 336 d2 l excavator (prefix ggh) service repair manual (ggh000...fhjsjkdmemm
The document provides instructions for disassembling and assembling the piston pump (hydraulic fan) of an excavator model 336D2. The disassembly procedure involves removing 22 parts from the pump housing, including springs, seals, pistons, and bearings. The assembly procedure lists 30 steps to reinstall the parts in reverse order and adjust clearances using various tools. Precautions are provided to prevent injury from spring forces.
Caterpillar cat 336 d2 l excavator (prefix far) service repair manual (far000...fhjsjkdmemm
This document provides instructions for installing a final drive and travel motor on an excavator. It outlines 11 steps, including positioning the travel motor and final drive with lifting devices, installing O-rings and seals, connecting hoses and fittings, and tightening bolts to specified torques. Safety notices are provided to handle fluids properly and keep components clean from contaminants. Required tools include vacuum caps, link brackets, and anti-seize compound.
Caterpillar cat 336 d2 l excavator (prefix elr) service repair manual (elr000...fhjsjkdmemm
This document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tubes, hoses and harnesses from the pump before removing mounting bolts and the pump. For installation, the process is reversed - mounting bolts are installed and all connections reattached. Proper cleaning and use of new O-rings is emphasized to prevent contamination.
Caterpillar cat 336 d2 l excavator (prefix eft) service repair manual (eft000...fhjsjkdmemm
This document provides instructions for disassembling and assembling the travel motor on 336D2 and 336D2 L excavators. The disassembly process involves using various tools to remove components like retaining rings, seals, pistons, springs, and bearings. The assembly process describes installing these components in reverse order and notes that cleanliness is important, components should be lubricated, and parts must be installed in their proper positions and orientations.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D EXCAVATOR PHH
Configuration: 312D & 312D L Excavators PHH00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02743771
Flywheel - Remove
SMCS - 1156-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
B Forcing bolts M16 - 2 by 120 mm 2
Start By:
a. Remove the crankshaft position sensor. Refer to Disassembly and Assembly, "Crankshaft
Position Sensor - Remove and Install".
b. Remove the muffler. Refer to Disassembly and Assembly, "Muffler - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
312D & 312D L Excavators PHH00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g01374966
1. Remove muffler brackets (1).
Illustration 2 g01374968
Illustration 3 g01374970
2. Remove bolts (2).
3. Install Tooling (A) and a suitable lifting device onto flywheel (3).
4. Use Tooling (B) in order to remove flywheel (3) out of the housing. The weight of flywheel
(3) is approximately 50 kg (110 lb).
2/3
312D & 312D L Excavators PHH00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 5. Perform the following procedure in order to remove the flywheel ring gear.
Illustration 4 g01374977
Typical Example
a. Place flywheel (3) and ring gear (4) on suitable cribbing.
Note: Mark the orientation of ring gear (4) on flywheel (3) for assembly purposes.
Always wear protective gloves when handling parts that have been
heated.
b. Raise the temperature of ring gear (4) uniformly.
c. Remove the ring gear (4) by tapping ring gear (4) all the way around flywheel (3).
d. Reposition flywheel (3) in order to remove ring gear (4).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue May 26 08:28:08 UTC+0800 2020
3/3
312D & 312D L Excavators PHH00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D EXCAVATOR PHH
Configuration: 312D & 312D L Excavators PHH00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02744399
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Always wear protective gloves when handling parts that have been
heated.
1. Perform the following procedure, if the ring gear was removed from the flywheel:
a. Raise the temperature of the ring gear 149 °C (300 °F).
1/3
312D & 312D L Excavators PHH00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. b. Use a suitable press in order to install the ring gear onto the flywheel.
Note: Prior to the installation of the flywheel, refer to Specifications, "Flywheel" for
information on checking the flywheel assembly for flatness.
Illustration 1 g01374993
2. Install Tooling (A) and a suitable lifting device onto flywheel (3).
3. Install flywheel (3). The weight of flywheel (3) is approximately 50 kg (110 lb).
Illustration 2 g01374968
4. Install bolts (2) in order to secure flywheel (3) onto the crankshaft. Tighten bolts (2) to a
torque of 83 ± 5 N·m (61 ± 4 lb ft).
5. Remove Tooling (A) from flywheel (3).
2/3
312D & 312D L Excavators PHH00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 3 g01374966
6. Install muffler brackets (1).
7. Check the flywheel runout. Refer to Testing and Adjusting, "Flywheel Housing - Inspect"
for more information on flywheel runout.
End By:
a. Install the muffler. Refer to Disassembly and Assembly, "Muffler - Remove and Install".
b. Install the crankshaft position sensor. Refer to Disassembly and Assembly, "Crankshaft
Position Sensor - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue May 26 08:29:07 UTC+0800 2020
3/3
312D & 312D L Excavators PHH00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D EXCAVATOR PHH
Configuration: 312D & 312D L Excavators PHH00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i01135944
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
B
5P-7312 Seal Distorter 1
5P-7338 Distorter Ring 2
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
1/3
312D & 312D L Excavators PHH00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00604840
Note: If the oil seal shows a sign of oil leaks, remove the wear sleeve and the oil seal.
1. Drill three evenly spaced 3 mm (0.12 inch) holes in crankshaft rear seal (1).
2. Use Tool (A) to remove the crankshaft rear seal.
Illustration 2 g00604844
3. Use Tool (B) to remove the wear sleeve (2) (not shown) from the rear of the crankshaft.
Note: When you are removing the wear sleeve, take extreme care not to damage the
crankshaft.
2/3
312D & 312D L Excavators PHH00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D EXCAVATOR PHH
Configuration: 312D & 312D L Excavators PHH00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i01615317
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
9U-6169 Installer 1
9U-6171 Locator 1
9U-6172 Bolt 2
5P-8247 Hard Washer 1
6V-3303 Bolt 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. To install a new wear sleeve that is complete with a seal, use 169-5464 Quick Cure Primer
to clean the outer diameter of the crankshaft and the inside diameter of the wear sleeve.
Apply 4C-9507 Retaining Compound to the faces of all the mating parts.
1/3
312D & 312D L Excavators PHH00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 1 g00604874
2. Install a new wear sleeve that is complete with a seal (1) (not shown) with Tool (A), as
follows:
Illustration 2 g00604875
a. Install 9U-6171 Locator (3) onto the crankshaft with 9U-6172 Bolt (4).
b. Put the new wear sleeve that is complete with a seal in 9U-6169 Installer (2).
c. Put 6V-3303 Bolt (6) through 5P-8247 Hard Washer (5) and 9U-6169 Installer (2)
and thread into 9U-6171 Locator (3).
d. Push the wear sleeve that is complete with a seal onto the crankshaft until 9U-6169
Installer (2) bottoms out.
2/3
312D & 312D L Excavators PHH00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 3 g00604874
e. Remove Tool (A) and check crankshaft rear seal (1) (not shown) for correct
installation.
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue May 26 08:31:06 UTC+0800 2020
3/3
312D & 312D L Excavators PHH00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D EXCAVATOR PHH
Configuration: 312D & 312D L Excavators PHH00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02742697
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
B 1P-0510 Driver Group 1
Start By:
a. Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor- Remove and Install".
b. Remove the flywheel and ring gear. Refer to Disassembly and Assembly, "Flywheel -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
312D & 312D L Excavators PHH00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 1 g01374571
1. Install Tooling (A), and a suitable lifting device onto flywheel housing (3).
2. Remove bolts (2) and the washers that secure flywheel housing (3) to the cylinder block.
3. Remove flywheel housing (3). The weight of flywheel (3) is approximately 29 kg (65 lb).
4. Remove gasket (1) (not shown).
Illustration 2 g01374572
5. Use Tooling (B) in order to remove the oil seal (4) (not shown).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
B 1P-0510 Driver Group 1
NOTICE
2/4
312D & 312D L Excavators PHH00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 3 g01374614
1. Use Tooling (B) in order to install the oil seal (4) (not shown).
Illustration 4 g01374571
2. Check the condition of two dowels (not shown). If dowels are damaged, use new parts for
replacement.
3. Clean old gasket (1) (not shown) from the mating surfaces of the cylinder block and the
flywheel housing. Install a new gasket on the cylinder block.
4. Place flywheel housing (3) in position on the cylinder block.
5. Install the washers and bolts (2) in order to secure flywheel housing (3) to the cylinder
block.
6. Remove Tooling (A).
End By:
3/4
312D & 312D L Excavators PHH00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
b. Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor- Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue May 26 08:32:05 UTC+0800 2020
4/4
312D & 312D L Excavators PHH00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D EXCAVATOR PHH
Configuration: 312D & 312D L Excavators PHH00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i06790404
Crankshaft Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2321 Combination Puller 1
B 6V-9120 Socket(1)
1
(1)
Tooling (B) is a 46 mm socket.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Remove the belt. Refer to Operation and Maintenance Manual, "Belt -
Inspect/Adjust/Replace".
1/4
312D & 312D L Excavators PHH00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 1 g00604778
2. Use Tooling (B) in order to remove nut (1) and washer (2) from the threaded end of the
crankshaft.
Illustration 2 g00604784
3. Use Tooling (A) in order to remove crankshaft pulley (3) from the engine.
2/4
312D & 312D L Excavators PHH00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 3 g00604792
4. If it is necessary to remove wear sleeve (4) from crankshaft pulley (3), use a suitable
hammer and a suitable chisel. Hold the suitable chisel at right angles to the surface of the
wear sleeve. Tap the wear sleeve in three places. You can remove the wear sleeve once the
tension is released.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
B 6V-9120 Socket(1)
1
C 1P-0510 Driver Gp 1
(1)
Tooling (B) is a 46 mm socket.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Raise the temperature of the wear sleeve. Use Tooling (C) in order to install the wear sleeve
onto the crankshaft pulley.
3/4
312D & 312D L Excavators PHH00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 4 g01377941
2. Ensure that baffle plate (5) is oriented, as shown.
Illustration 5 g00604778
3. Position crankshaft pulley (3) onto the engine.
4. Install washer (2) and nut (1). Use Tooling (B) in order to tighten nut (1) to a torque of
707.5 ± 57.5 N·m (522 ± 42 lb ft).
5. Install the belt. Refer to Operation and Maintenance Manual, "Belt -
Inspect/Adjust/Replace".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue May 26 08:33:05 UTC+0800 2020
4/4
312D & 312D L Excavators PHH00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D EXCAVATOR PHH
Configuration: 312D & 312D L Excavators PHH00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02742689
Crankshaft Front Seal - Remove
SMCS - 1160-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
Start By:
a. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/2
312D & 312D L Excavators PHH00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00529162
Typical Example
1. Drill three evenly spaced 3.0 mm (0.12 inch) holes in crankshaft front seal (1).
2. Use Tooling (A) in order to remove crankshaft front seal (1). Remove the seal evenly by
alternating the position of Tooling (A) from hole to hole.
Note: Do not damage the flange of the crankshaft during the removal process for the
crankshaft front seal.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue May 26 08:34:04 UTC+0800 2020
2/2
312D & 312D L Excavators PHH00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D EXCAVATOR PHH
Configuration: 312D & 312D L Excavators PHH00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02742692
Crankshaft Front Seal - Install
SMCS - 1160-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6180 Front Seal Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
312D & 312D L Excavators PHH00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 1 g00612743
Typical Example
1. Clean the faces of all the mating parts. Apply a thin coat of clean engine oil to a new
crankshaft front seal.
2. Use Tooling (A) in order to install new crankshaft front seal (1) in the front housing.
3. Remove Tooling (A) and check crankshaft front seal (1) for correct installation.
4. Apply clean engine oil to the face of the crankshaft pulley that will be in contact with the
new crankshaft front seal.
End By:
a. Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue May 26 08:35:03 UTC+0800 2020
2/2
312D & 312D L Excavators PHH00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D EXCAVATOR PHH
Configuration: 312D & 312D L Excavators PHH00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02742863
Gear Group (Front) - Remove - Idler Gear Only
SMCS - 1206-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6148 Idler Shaft Puller 1
B 1P-0510 Driver Group 1
Start By:
a. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/4
312D & 312D L Excavators PHH00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01374732
(1) Fuel injection pump drive gear
(2) Idler gear
(3) Camshaft gear
(4) Crankshaft gear
Note: The No. 1 cylinder is at the top center position when these marks are in alignment.
Note: Ensure that the marks on the timing gears are in alignment.
2/4
312D & 312D L Excavators PHH00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Illustration 2 g01374789
1. Remove idler gear bolt (5) and the washer from the idler gear shaft .
2. Remove thrust plate (6) from the idler gear shaft.
Illustration 3 g01374793
3. Remove idler gear (2) from the idler gear shaft.
Illustration 4 g01374804
4. If necessary, use Tooling (B) and a suitable press in order to remove bushing (7) (not
shown) from idler gear (2).
3/4
312D & 312D L Excavators PHH00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...