This service repair manual provides instructions for removing and installing inlet and exhaust valve seals on models 311C and 311C U excavators. The document describes the required tools and provides a step-by-step procedure for removing the old seals and installing new ones. It also includes guidelines for cleaning parts and contains illustrations supporting the instructions.
The document provides instructions for removing and installing valve stem seals, engine oil filter base, and engine oil cooler on Caterpillar 3064 and 3066 engines. The removal procedures describe using tools to remove old parts and inspecting components. The installation procedures describe cleaning parts, applying oil, and securing components with bolts and washers.
Caterpillar Cat 311C U Excavator (Prefix CKE) Service Repair Manual (CKE00001...tuzhiyou2
The document provides instructions for removing and installing valve stem seals, engine oil filter bases, and engine oil coolers on Caterpillar 3064 and 3066 engines. The procedures describe using various tools to remove old parts and install new seals, filters, and coolers, checking for wear and contaminants, and ensuring proper lubrication. Safety notices are included to handle fluids and contain contaminants properly.
Caterpillar Cat 311C U Excavator (Prefix CKE) Service Repair Manual (CKE00001...qfyc504378
The document provides instructions for removing and installing valve stem seals, engine oil filter bases, engine oil coolers, and disassembling and assembling engine oil coolers on Caterpillar 3064 and 3066 engines. The procedures describe using various tools to remove old parts and install new parts, checking components for wear or damage, and ensuring parts are clean to prevent contamination. Cautions are provided regarding containing fluids, collecting waste, and preventing rapid wear from contaminants.
The document provides instructions for removing and installing valve stem seals, engine oil filter bases, engine oil coolers, and disassembling and assembling engine oil coolers on Caterpillar 3064 and 3066 engines. The procedures describe using various tools to remove old parts and install new parts, checking components for wear or damage, and ensuring parts are clean to prevent contamination. Safety notices are provided regarding containing fluids, collecting waste, and preventing contact with hot oil or components.
The document provides instructions for removing and installing valve stem seals, engine oil filter base, and engine oil cooler on Caterpillar 3064 and 3066 engines. The removal procedures describe using tools to remove old parts and inspecting components. The installation procedures describe cleaning parts, applying oil, and securing components with bolts and washers.
Caterpillar Cat 311C U Excavator (Prefix CKE) Service Repair Manual (CKE00001...lituo39419496
The document provides instructions for removing and installing valve stem seals, engine oil filter base, and engine oil cooler on Caterpillar 3064 and 3066 engines. The removal procedures describe using tools to remove old parts and inspecting components. The installation procedures describe cleaning parts, applying oil, and securing components with bolts and washers.
Caterpillar Cat 312D2 L Excavator (Prefix EAB) Service Repair Manual (EAB0000...tuzhiyou2
1) The document provides instructions for installing the rocker shaft and pushrods on a Caterpillar 3054C engine. It describes cleaning and lubricating the parts, compressing the springs using a tool, and tightening the screws in a specific sequence.
2) The instructions then describe removing the cylinder head, which requires draining fluids and removing other engine components first. Dowel pins must be aligned during installation.
3) Reinstalling the cylinder head requires cleaning, torquing bolts in a sequence, and refilling fluids. New gaskets are also replaced.
1) The document provides instructions for installing the rocker shaft and pushrods on a Caterpillar 3054C engine. It describes cleaning and lubricating the parts, compressing the springs using a tool, and tightening the screws in a specific sequence.
2) The instructions then describe removing the cylinder head, which requires draining fluids and removing other engine components first. Dowel pins must be aligned during installation.
3) Reinstalling the cylinder head requires cleaning, torquing bolts in a sequence, and refilling fluids. Tools are used to install and correctly torque the bolts.
The document provides instructions for removing and installing valve stem seals, engine oil filter base, and engine oil cooler on Caterpillar 3064 and 3066 engines. The removal procedures describe using tools to remove old parts and inspecting components. The installation procedures describe cleaning parts, applying oil, and securing components with bolts and washers.
Caterpillar Cat 311C U Excavator (Prefix CKE) Service Repair Manual (CKE00001...tuzhiyou2
The document provides instructions for removing and installing valve stem seals, engine oil filter bases, and engine oil coolers on Caterpillar 3064 and 3066 engines. The procedures describe using various tools to remove old parts and install new seals, filters, and coolers, checking for wear and contaminants, and ensuring proper lubrication. Safety notices are included to handle fluids and contain contaminants properly.
Caterpillar Cat 311C U Excavator (Prefix CKE) Service Repair Manual (CKE00001...qfyc504378
The document provides instructions for removing and installing valve stem seals, engine oil filter bases, engine oil coolers, and disassembling and assembling engine oil coolers on Caterpillar 3064 and 3066 engines. The procedures describe using various tools to remove old parts and install new parts, checking components for wear or damage, and ensuring parts are clean to prevent contamination. Cautions are provided regarding containing fluids, collecting waste, and preventing rapid wear from contaminants.
The document provides instructions for removing and installing valve stem seals, engine oil filter bases, engine oil coolers, and disassembling and assembling engine oil coolers on Caterpillar 3064 and 3066 engines. The procedures describe using various tools to remove old parts and install new parts, checking components for wear or damage, and ensuring parts are clean to prevent contamination. Safety notices are provided regarding containing fluids, collecting waste, and preventing contact with hot oil or components.
The document provides instructions for removing and installing valve stem seals, engine oil filter base, and engine oil cooler on Caterpillar 3064 and 3066 engines. The removal procedures describe using tools to remove old parts and inspecting components. The installation procedures describe cleaning parts, applying oil, and securing components with bolts and washers.
Caterpillar Cat 311C U Excavator (Prefix CKE) Service Repair Manual (CKE00001...lituo39419496
The document provides instructions for removing and installing valve stem seals, engine oil filter base, and engine oil cooler on Caterpillar 3064 and 3066 engines. The removal procedures describe using tools to remove old parts and inspecting components. The installation procedures describe cleaning parts, applying oil, and securing components with bolts and washers.
Caterpillar Cat 312D2 L Excavator (Prefix EAB) Service Repair Manual (EAB0000...tuzhiyou2
1) The document provides instructions for installing the rocker shaft and pushrods on a Caterpillar 3054C engine. It describes cleaning and lubricating the parts, compressing the springs using a tool, and tightening the screws in a specific sequence.
2) The instructions then describe removing the cylinder head, which requires draining fluids and removing other engine components first. Dowel pins must be aligned during installation.
3) Reinstalling the cylinder head requires cleaning, torquing bolts in a sequence, and refilling fluids. New gaskets are also replaced.
1) The document provides instructions for installing the rocker shaft and pushrods on a Caterpillar 3054C engine. It describes cleaning and lubricating the parts, compressing the springs using a tool, and tightening the screws in a specific sequence.
2) The instructions then describe removing the cylinder head, which requires draining fluids and removing other engine components first. Dowel pins must be aligned during installation.
3) Reinstalling the cylinder head requires cleaning, torquing bolts in a sequence, and refilling fluids. Tools are used to install and correctly torque the bolts.
Caterpillar Cat W345B Series II Material Handler (Prefix CDY) Service Repair ...paws21610697
This document provides assembly instructions for a swing drive on a W345B Series II wheeled excavator. It includes a list of required tools and 40 steps to assemble the various components of the swing drive, such as bearings, seals, gears, and housings. Special attention is given to cleaning parts, applying lubricants, and torquing bolts to the specified values. The instructions also cover installing the assembled swing drive into the excavator's main frame.
1. Remove the fuel injection pump housing and governor from the engine as a single unit using lifting sling and hoist. Disconnect all connecting lines and tubes.
2. Disassemble the fuel injection pump housing by removing the retaining ring, filter base, tubes and other attached components.
3. Inspect all seals and gaskets, replacing any that are damaged, to prepare the housing for assembly.
This document provides installation instructions for removing and installing an axle shaft on the steering axle of an M325D Material Handler excavator. It is a 15 step process that includes draining fluids, removing bolts and pins, lifting out heavy components using lifting devices, replacing seals and bushings, and reinstalling components in reverse order. Special tools are required and Loctite threadlocker is used on reinstallation.
Caterpillar Cat M325D L MH EXCAVATOR (Prefix KAY) Service Repair Manual (KAY0...paws21610697
This document provides installation instructions for separating an upper frame from an undercarriage frame on an excavator. It outlines 33 steps including removing components like the stick, front and rear drive shafts, swivel, and left boom cylinder. It instructs using tools and lifting devices to reposition pins and plates to separate the frames while supporting heavy components weighing up to 500 pounds. Proper identification of hose and tube assemblies is noted for reinstallation.
Caterpillar Cat M325D L MH EXCAVATOR (Prefix KAY) Service Repair Manual (KAY0...paws21610697
This document provides instructions for disassembling and assembling the swing drive of an M325D L Material Handler excavator. It lists the required tools and presents a 31 step disassembly procedure and a 29 step assembly procedure. The procedures involve removing and installing various components of the swing drive like gears, shafts, bearings, seals and housings. Precautions are provided regarding cleanliness and safety.
The document provides instructions for disassembling the front and rear final drive carriers, hubs, and brakes of an M320 excavator. The 28 step procedure describes how to remove components like planetary carriers, sun gears, ring gears, brake pistons, bearings, and seals. Tools required include retaining ring pliers, pullers, wrenches, and hammers. Safety notices are provided to release hydraulic pressure and contain fluids before disassembly.
This document provides instructions for disassembling and assembling the rear axle carrier, hubs, and brakes of an M318F wheeled excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for removing components like the carrier housing, planetary gears, and brake discs, and installing components like the thrust washer, carrier gear, and retaining rings. The instructions aim to properly remove and replace these components while containing fluids and following safety procedures.
This document provides instructions for disassembling and assembling the rear axle carrier, hubs, and brakes of an M317F wheeled excavator. The disassembly procedure involves removing 23 components including carrier housing, planetary gears, thrust washers, retaining rings, and hub. The assembly procedure provides steps to install 23 components in reverse order and includes checking brake clearance and installing seals and bearings. Tools required include retaining ring pliers, drivers, spanners, pry bars, pullers, and torque wrenches.
The document provides instructions for removing and installing various components on a M317D2 Wheeled Excavator, including:
- Removing the swing gear and bearing by lifting it out after removing bolts and spacers.
- Installing the swing gear and bearing by positioning it with lifting tools, then installing bolts and spacers.
- Removing the hydraulic oil filter by taking off the cover, O-ring, and retainer, then removing the filter.
- Installing the hydraulic oil filter by reversing the removal steps.
- Removing the hydraulic tank by draining it, disconnecting hoses and fittings, and lifting it off after removing bolts.
- Installing the hydraulic tank by
The document provides instructions for disassembling and assembling the main hydraulic pump of a M317D2 Wheeled Excavator. It lists 34 steps for disassembly, removing components like pistons, springs, seals and bearings. It then lists 36 steps for assembly, replacing components and using various tools to set dimensions and install retaining rings, seals and bearings. Precision is required to mark positions of parts and reinstall components in their original orientation for proper function.
This document provides instructions for disassembling and assembling a swing drive on a wheeled excavator model M316D. The removal procedure involves releasing hydraulic pressure, removing hoses and bolts, and using lifting tools to remove the swing drive assembly. The disassembly procedure then describes using various tools to remove retaining rings, plates, discs, seals, gears, and other internal components. The assembly procedure outlines cleaning and lubricating parts, and using tools to reinstall components in reverse order, taking care to properly seat bearings and tighten nuts to the specified torques.
The document provides instructions for disassembling the front and rear axles of an M315F wheeled excavator. It lists required tools and presents a 23 step procedure for removing components like carrier housings, planetary gears, bearings, seals, and hubs. Detailed illustrations accompany each step to show how to properly disassemble parts. Safety notices are included to handle fluids and springs safely during the process.
The document provides disassembly and assembly instructions for the travel motor of an M312 excavator. It lists 44 steps to disassemble the travel motor and its components. These include removing covers, gaskets, seals, valves, springs, pins, and other parts. It then lists the assembly steps in reverse order, noting to replace all seals and gaskets, apply oil, and ensure cleanliness during assembly.
Caterpillar Cat M312 Excavator (Prefix 6TL) Service Repair Manual (6TL00001-0...paws21610697
This document provides the disassembly and assembly procedures for the swing drive of an M312 excavator. The disassembly procedure involves 28 steps to remove components such as the swing brake assembly, discs, plates, piston, seals, shaft, gears, bearings, and housing. The assembly procedure involves 17 steps and requires various tools to install components in the reverse order of disassembly while applying lubricant and ensuring proper torque specifications are achieved.
This document provides instructions for removing and installing engine oil filter bases and related components on Caterpillar 3304B and 3306B engines. The procedures describe removing the oil filter, oil filter base, gaskets and O-rings. Instructions are provided for disassembling the oil filter base by removing covers, bolts, springs and plungers. Reassembly and installation steps are also outlined. Tools required are listed for each procedure. Precautions are noted to keep parts clean and contain fluids.
Caterpillar Cat D250E II Articulated Truck (Prefix 4PS) Service Repair Manual...paws21610697
The document provides instructions for disassembling and assembling the piston pump used for steering on a D250E II Articulated Truck. The disassembly procedure involves removing 21 individual parts from the pump housing. The assembly procedure instructs assembling the 21 parts in the reverse order, applying lubrication and torque specifications as needed. Tools required include various drivers, pliers, and lubricants.
The document provides instructions for disassembling and assembling the governor of an articulated truck. It lists 57 steps to disassemble the front and rear housings of the governor. Tools required include a governor repair fixture, retaining ring pliers, pin punch, clevis driver, and legs to mount the rear housing. Cautions are provided regarding cleaning parts and containing fluids during maintenance.
The document provides instructions for disassembling and assembling a Type I governor used in Caterpillar 3114, 3116, and 3126 engines. It describes 35 steps to disassemble the governor front housing and 19 additional steps to disassemble the rear housing. Various parts are inspected for wear or damage during disassembly. Cleaning and replacement parts are also discussed. Tools required are listed.
The document provides instructions for removing and installing various engine components on a Caterpillar 3408 industrial engine, including the oil cooler, oil filter base, oil bypass valves, engine oil cooler/lines, aftercooler, and turbocharger. The procedures describe removing bolts, hoses, seals, and other parts, cleaning components, applying sealant, and reinstalling parts in reverse order.
The document provides instructions for removing and installing wheel spindles on Caterpillar articulated dump trucks. It describes removing the wheels, bearings, and seals before removing the brake shoes. It then details removing pins and springs to separate the brake shoes from the spider. Reinstallation follows the reverse order. Instructions are also given for disassembling and assembling suspension cylinders.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Caterpillar Cat W345B Series II Material Handler (Prefix CDY) Service Repair ...paws21610697
This document provides assembly instructions for a swing drive on a W345B Series II wheeled excavator. It includes a list of required tools and 40 steps to assemble the various components of the swing drive, such as bearings, seals, gears, and housings. Special attention is given to cleaning parts, applying lubricants, and torquing bolts to the specified values. The instructions also cover installing the assembled swing drive into the excavator's main frame.
1. Remove the fuel injection pump housing and governor from the engine as a single unit using lifting sling and hoist. Disconnect all connecting lines and tubes.
2. Disassemble the fuel injection pump housing by removing the retaining ring, filter base, tubes and other attached components.
3. Inspect all seals and gaskets, replacing any that are damaged, to prepare the housing for assembly.
This document provides installation instructions for removing and installing an axle shaft on the steering axle of an M325D Material Handler excavator. It is a 15 step process that includes draining fluids, removing bolts and pins, lifting out heavy components using lifting devices, replacing seals and bushings, and reinstalling components in reverse order. Special tools are required and Loctite threadlocker is used on reinstallation.
Caterpillar Cat M325D L MH EXCAVATOR (Prefix KAY) Service Repair Manual (KAY0...paws21610697
This document provides installation instructions for separating an upper frame from an undercarriage frame on an excavator. It outlines 33 steps including removing components like the stick, front and rear drive shafts, swivel, and left boom cylinder. It instructs using tools and lifting devices to reposition pins and plates to separate the frames while supporting heavy components weighing up to 500 pounds. Proper identification of hose and tube assemblies is noted for reinstallation.
Caterpillar Cat M325D L MH EXCAVATOR (Prefix KAY) Service Repair Manual (KAY0...paws21610697
This document provides instructions for disassembling and assembling the swing drive of an M325D L Material Handler excavator. It lists the required tools and presents a 31 step disassembly procedure and a 29 step assembly procedure. The procedures involve removing and installing various components of the swing drive like gears, shafts, bearings, seals and housings. Precautions are provided regarding cleanliness and safety.
The document provides instructions for disassembling the front and rear final drive carriers, hubs, and brakes of an M320 excavator. The 28 step procedure describes how to remove components like planetary carriers, sun gears, ring gears, brake pistons, bearings, and seals. Tools required include retaining ring pliers, pullers, wrenches, and hammers. Safety notices are provided to release hydraulic pressure and contain fluids before disassembly.
This document provides instructions for disassembling and assembling the rear axle carrier, hubs, and brakes of an M318F wheeled excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for removing components like the carrier housing, planetary gears, and brake discs, and installing components like the thrust washer, carrier gear, and retaining rings. The instructions aim to properly remove and replace these components while containing fluids and following safety procedures.
This document provides instructions for disassembling and assembling the rear axle carrier, hubs, and brakes of an M317F wheeled excavator. The disassembly procedure involves removing 23 components including carrier housing, planetary gears, thrust washers, retaining rings, and hub. The assembly procedure provides steps to install 23 components in reverse order and includes checking brake clearance and installing seals and bearings. Tools required include retaining ring pliers, drivers, spanners, pry bars, pullers, and torque wrenches.
The document provides instructions for removing and installing various components on a M317D2 Wheeled Excavator, including:
- Removing the swing gear and bearing by lifting it out after removing bolts and spacers.
- Installing the swing gear and bearing by positioning it with lifting tools, then installing bolts and spacers.
- Removing the hydraulic oil filter by taking off the cover, O-ring, and retainer, then removing the filter.
- Installing the hydraulic oil filter by reversing the removal steps.
- Removing the hydraulic tank by draining it, disconnecting hoses and fittings, and lifting it off after removing bolts.
- Installing the hydraulic tank by
The document provides instructions for disassembling and assembling the main hydraulic pump of a M317D2 Wheeled Excavator. It lists 34 steps for disassembly, removing components like pistons, springs, seals and bearings. It then lists 36 steps for assembly, replacing components and using various tools to set dimensions and install retaining rings, seals and bearings. Precision is required to mark positions of parts and reinstall components in their original orientation for proper function.
This document provides instructions for disassembling and assembling a swing drive on a wheeled excavator model M316D. The removal procedure involves releasing hydraulic pressure, removing hoses and bolts, and using lifting tools to remove the swing drive assembly. The disassembly procedure then describes using various tools to remove retaining rings, plates, discs, seals, gears, and other internal components. The assembly procedure outlines cleaning and lubricating parts, and using tools to reinstall components in reverse order, taking care to properly seat bearings and tighten nuts to the specified torques.
The document provides instructions for disassembling the front and rear axles of an M315F wheeled excavator. It lists required tools and presents a 23 step procedure for removing components like carrier housings, planetary gears, bearings, seals, and hubs. Detailed illustrations accompany each step to show how to properly disassemble parts. Safety notices are included to handle fluids and springs safely during the process.
The document provides disassembly and assembly instructions for the travel motor of an M312 excavator. It lists 44 steps to disassemble the travel motor and its components. These include removing covers, gaskets, seals, valves, springs, pins, and other parts. It then lists the assembly steps in reverse order, noting to replace all seals and gaskets, apply oil, and ensure cleanliness during assembly.
Caterpillar Cat M312 Excavator (Prefix 6TL) Service Repair Manual (6TL00001-0...paws21610697
This document provides the disassembly and assembly procedures for the swing drive of an M312 excavator. The disassembly procedure involves 28 steps to remove components such as the swing brake assembly, discs, plates, piston, seals, shaft, gears, bearings, and housing. The assembly procedure involves 17 steps and requires various tools to install components in the reverse order of disassembly while applying lubricant and ensuring proper torque specifications are achieved.
This document provides instructions for removing and installing engine oil filter bases and related components on Caterpillar 3304B and 3306B engines. The procedures describe removing the oil filter, oil filter base, gaskets and O-rings. Instructions are provided for disassembling the oil filter base by removing covers, bolts, springs and plungers. Reassembly and installation steps are also outlined. Tools required are listed for each procedure. Precautions are noted to keep parts clean and contain fluids.
Caterpillar Cat D250E II Articulated Truck (Prefix 4PS) Service Repair Manual...paws21610697
The document provides instructions for disassembling and assembling the piston pump used for steering on a D250E II Articulated Truck. The disassembly procedure involves removing 21 individual parts from the pump housing. The assembly procedure instructs assembling the 21 parts in the reverse order, applying lubrication and torque specifications as needed. Tools required include various drivers, pliers, and lubricants.
The document provides instructions for disassembling and assembling the governor of an articulated truck. It lists 57 steps to disassemble the front and rear housings of the governor. Tools required include a governor repair fixture, retaining ring pliers, pin punch, clevis driver, and legs to mount the rear housing. Cautions are provided regarding cleaning parts and containing fluids during maintenance.
The document provides instructions for disassembling and assembling a Type I governor used in Caterpillar 3114, 3116, and 3126 engines. It describes 35 steps to disassemble the governor front housing and 19 additional steps to disassemble the rear housing. Various parts are inspected for wear or damage during disassembly. Cleaning and replacement parts are also discussed. Tools required are listed.
The document provides instructions for removing and installing various engine components on a Caterpillar 3408 industrial engine, including the oil cooler, oil filter base, oil bypass valves, engine oil cooler/lines, aftercooler, and turbocharger. The procedures describe removing bolts, hoses, seals, and other parts, cleaning components, applying sealant, and reinstalling parts in reverse order.
The document provides instructions for removing and installing wheel spindles on Caterpillar articulated dump trucks. It describes removing the wheels, bearings, and seals before removing the brake shoes. It then details removing pins and springs to separate the brake shoes from the spider. Reinstallation follows the reverse order. Instructions are also given for disassembling and assembling suspension cylinders.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 311C EXCAVATOR CKE
Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01150941
Inlet and Exhaust Valve Seals - Remove and Install
SMCS - 1104-010-SA
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-1720 Seal Pick 1
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00610601
Illustration 2 g00610605
1. Use Tool (A) to remove valve stem seal (1) from the inlet and exhaust valve guide.
Illustration 1 shows the removal of the valve stem seal, when the valve guide (2) is removed
from cylinder head (4) .
Illustration 2 shows the removal of the valve stem seal, while the valve guide (2) is installed
in cylinder head (4) .
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 5P-1720 Seal Pick 1
NOTICE
Keep all parts clean from contaminants.
2/4
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Contaminants may cause rapid wear and shortened component life.
Note: Do not apply any oil or sealant to the mating surface of the valve seal that comes into
contact with the valve guide. When the valve seal is installed, coat the surface of the valve stem
with engine oil in order to ensure initial lubrication of the seal lip.
Illustration 3 g00610601
Illustration 4 g00610605
1. Place the new valve stem seal in position on the valve guide.
2. Use Tool (A) to assist in installing the new valve stem seal.
Illustration 3 shows the installation of the valve stem seal, when the valve guide (2) is
removed from the cylinder head (4) .
Illustration 4 shows the installation of the valve stem seal, while the valve guide (2) is
installed in the cylinder head (4) .
Note: After the valve stem seal is installed on the valve guide, ensure that the seal is
properly installed in the groove of the valve guide.
3/4
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. End By: Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Nov 10 22:19:02 UTC+0800 2020
4/4
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 311C EXCAVATOR CKE
Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01565892
Engine Oil Filter Base - Remove
SMCS - 1306-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench Assembly 1
Hot oil and components can cause personal injury.
Do not allow hot oil or components to contact skin.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
1/3
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00813775
Illustration 2 g00813789
1. Use Tool (A) and remove oil filter (2) from engine oil filter base (3) .
2. Remove the bolts (1) and washers from the engine oil filter base (3) .
3. Remove engine oil filter base (3) from the engine.
2/3
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. 4. Check the condition of O-ring seals (4). Replace the O-ring seals, if the O-ring seals are
worn or damaged.
Illustration 3 g00813823
5. If necessary, remove eight bolts (6) and the washers in order to remove plate (5) from the
engine.
6. Check the condition of gasket (not shown). Replace the gasket, if the gasket is worn or
damaged.
7. Check engine oil filter base (3) and plate (5) for clogging and cracks. Replace damaged
components with replacement parts.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Nov 10 22:19:58 UTC+0800 2020
3/3
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 311C EXCAVATOR CKE
Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01565969
Engine Oil Filter Base - Install
SMCS - 1306-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00813823
1. Secure gasket and plate (5) to the cylinder block with eight bolts (6) .
1/2
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 2 g00813789
2. Check the condition of O-ring seals (4). Replace the O-ring seals, if the O-ring seals are
damaged.
Note: Coat all of the O-ring seals with clean engine oil prior to installation.
3. Install the O-ring seals (4) on engine oil filter base (3) .
Illustration 3 g00813775
4. Secure engine oil filter base (3) to the plate (5) with four bolts (1) and the washers.
5. Install the engine oil filter (2) to the engine oil filter base (3) .
Note: Follow the installation procedure on the engine oil filter in order to install the engine
oil filter on the engine oil filter base.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Nov 10 22:20:54 UTC+0800 2020
2/2
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 311C EXCAVATOR CKE
Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615275
Engine Oil Cooler - Remove
SMCS - 1378-011
Removal Procedure
Start By:
A. Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump
- Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/2
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 1 g00611319
1. If necessary, remove bolt (1) and the washer from the cylinder head.
2. Remove oil tube assembly (dipstick) (2) from the cylinder block.
3. Check O-ring seal (3) (not shown) for wear or damage. Replace the O-ring seal, if the O-
ring seal is worn or damaged.
Illustration 2 g00611320
4. Remove bolts (4) and the washers that secure the oil cooler to the engine cylinder block.
The 3066 Engine has 24 bolts and washers while the 3064 Engine has 16 bolts and washers.
5. Remove engine oil cooler (5) and gasket (6) (not shown) from the engine cylinder block.
Check the gasket for wear or damage. Replace the gasket, if the gasket is worn or damaged.
Note: Check the oil cooler cover for cracks. Replace the cover, if the cover is cracked.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Nov 10 22:21:49 UTC+0800 2020
2/2
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 311C EXCAVATOR CKE
Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01152039
Engine Oil Cooler - Disassemble
SMCS - 1378-015
Disassembly Procedure
Start By:
A. Remove the oil cooler. Refer to Disassembly and Assembly, "Engine Oil Cooler - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/3
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 1 g00618921
Illustration 2 g00611507
1. Remove four nuts (1) and the washers from the oil cooler core (3) .
2. Remove oil cooler core (3) from oil cooler cover (2) .
Note: Check the engine oil cooler core for cracks, clogging, and ruptures.
3. Remove two gaskets (4) from the oil cooler core. Check the gasket for wear or damage.
Replace the gaskets, if necessary.
2/3
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 311C EXCAVATOR CKE
Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01152137
Engine Oil Cooler - Assemble
SMCS - 1378-016
Assembly Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 1 g00618921
Illustration 2 g00611507
1. Install two gaskets (4) onto the oil cooler core (3) .
2. Install the oil cooler cover (2) onto the oil cooler core (3) .
3. Install four nuts (1) and the washers, which secure the oil cooler core to the oil cooler cover.
4. Tighten the four nuts (1) .
End By: Install the oil cooler. Refer to Disassembly and Assembly, "Engine Oil Cooler - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Nov 10 22:23:41 UTC+0800 2020
2/2
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 311C EXCAVATOR CKE
Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615279
Engine Oil Cooler - Install
SMCS - 1378-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00611320
1. Install engine oil cooler (5) and new gasket (6) (not shown). Ensure that all mating surfaces
are clean. Install bolts (4) and washers in order to secure the engine oil cooler to the engine
cylinder block. The 3066 Engine has 24 bolts and washers while the 3064 Engine has 16
bolts and washers.
1/2
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 2 g00611319
2. Install oil tube assembly (dipstick) (2) into the cylinder block.
Note: Apply clean engine oil to the O-ring seal (3) (not shown) before installation.
3. Install bolt (1) and the washer into the cylinder head.
End By: Install the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection
Pump - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Nov 10 22:24:37 UTC+0800 2020
2/2
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 311C EXCAVATOR CKE
Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615285
Engine Oil Relief Valve - Remove and Install
SMCS - 1315-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00607236
1/3
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 2 g00607247
1. Remove threaded plug (1) and the shim (2) for the engine oil relief valve from the right side
of the cylinder block.
2. Remove the spring (3) and spring seat (4) from the cylinder block.
Note: Check the spring seat (4) and the valve seat for an abnormal contact pattern. Inspect the
spring (3) for weakness or damage. If necessary, replace the engine oil relief valve with a new
part.
Note: Check the cylinder block for oil passages that are clogged.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 3 g00607247
Illustration 4 g00607236
1. Install spring seat (4) and spring (3) in the cylinder block.
2. Install shim (2) and threaded plug (1) in the cylinder block.
3. Tighten threaded plug (1) of the engine oil relief valve to a torque of 49 ± 5 N·m (36 ± 4 lb
ft).
Note: Test the opening pressure for the engine oil relief valve. The opening pressure for the
relief valve is 343 ± 20 kPa (50 ± 3 psi). Make adjustments by shimming, if necessary.
For more information, refer to Specifications, "Engine Oil Relief Valve".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Nov 10 22:25:33 UTC+0800 2020
3/3
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 311C EXCAVATOR CKE
Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615293
Engine Oil Bypass Valve - Remove and Install
SMCS - 1306-010-BV
Removal Procedure
Start By:
A. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00607679
1/3
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 2 g00607688
1. Remove threaded plug (1) for the engine oil bypass valve from the cylinder block (2) .
2. Remove shim (3) from the cylinder block (2) .
3. Remove spring (4) from the cylinder block (2) .
4. Remove spring seat (5) from the cylinder block (2) .
Note: Check the spring seat (5) and the valve seat for an abnormal contact pattern. Inspect the
spring (4) for weakness or damage. If necessary, replace the engine oil bypass valve with a new
part.
Note: Check the cylinder block (2) for oil passages that are clogged.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 3 g00607688
Illustration 4 g00607679
1. Install spring seat (5) (not shown) and spring (4) in the cylinder block (2) .
2. Install shim (3) and threaded plug (1) in the cylinder block (2) .
3. Tighten the threaded plug (1) to a torque of 69 ± 5 N·m (51 ± 4 lb ft).
Note: Test the opening pressure for the engine oil relief valve. The opening pressure for the
relief valve is 981 ± 98 kPa (142 ± 14 psi). Make adjustments by shimming, if necessary.
For information on testing the engine oil relief valve, refer to Testing and Adjusting, "Lubrication
System".
For more information, refer to Specifications, "Engine Oil Bypass Valve".
End By: Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan -
Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Nov 10 22:26:28 UTC+0800 2020
3/3
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 311C EXCAVATOR CKE
Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01146335
Engine Oil Pump - Remove
SMCS - 1304-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2320 Combination Puller 1
B 1P-0510 Driver Group 1
Start By:
A. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
1/5
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Thank you very much
for your reading.
Please click here to buy
After you pay.
Then, you can
download the complete
manual instantly.
No waiting.
27. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00607826
Note: Illustration 1 does not show that the front housing is removed from the cylinder
block.
1. Remove bolt (1) from the cover (2) .
2. Remove cover (2) for the engine oil pump from the front housing. Check gasket (3) (not
shown) for damage or wear. Replace the gasket, if the gasket is worn or damaged.
Illustration 2 g00607770
2/5
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. 3. Remove driven gear (4) for the oil pump. Pull the gear straight out of the front housing (5)
(slip fit).
Illustration 3 g00607857
4. Position the front housing on a work bench in order to remove the oil pump gear from the
rear of the housing.
5. Use Tool (A) to remove oil pump gear (6) from the front housing.
Illustration 4 g00607885
6. Position the front housing on a work bench in order to remove the drive gear from the front
of the housing.
7. Remove drive gear (7) from the front housing.
3/5
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...