The document provides instructions for disassembling and assembling a piston pump. It lists 34 steps for disassembling the pump, removing components like the piston, valve, plates, seals and bearings. It then lists 32 steps for reassembling the pump, replacing worn parts and ensuring proper torque of fasteners. Cleanliness is emphasized throughout to prevent contamination. Tools including snap ring pliers are required.
Caterpillar Cat 304.5 Mini Hydraulic Excavator (Prefix ANR) Service Repair Ma...tuzhiyou2
The document provides instructions for installing a piston pump on a 304.5 Mini Hydraulic Excavator. It outlines 31 steps to assemble the pump, including installing bearings, seals, plates, blocks, springs, rings and screws. Cleanliness is emphasized throughout the assembly process to prevent contaminants from entering the system. The pump is then installed on the excavator by referring to the installation procedure.
Caterpillar Cat 304.5 Mini Hydraulic Excavator (Prefix ANR) Service Repair Ma...qfyc504378
The document provides instructions for installing a piston pump on a 304.5 Mini Hydraulic Excavator. It outlines 31 steps to assemble the pump, including installing bearings, seals, plates, blocks, springs, rings and screws. Cleanliness is emphasized throughout the assembly process to prevent contaminants from entering the system. The pump is then installed on the excavator by referring to the installation procedure.
Caterpillar Cat 304.5 Mini Hydraulic Excavator (Prefix ANR) Service Repair Ma...lituo39419496
The document provides instructions for disassembling and assembling the piston pump of a 304.5 Mini Hydraulic Excavator. It lists 35 steps to disassemble the pump by removing components like the piston, pump head, springs, and seals. It then lists 32 steps for reassembling the pump by reversing the disassembly process and installing new seals and O-rings. Cleanliness is emphasized throughout to prevent contaminants from entering the system.
Caterpillar Cat 304.5 Mini Hydraulic Excavator (Prefix WAK) Service Repair Ma...jdjkskmikdkmd
This document provides instructions for removing a swing motor from a 304.5 Mini Hydraulic Excavator. The instructions involve releasing hydraulic system pressure, removing the cab and seat, disconnecting linkages from the left console, and removing bolts to detach the right console. Identification marks should be placed on all lines, hoses, wires and tubes before removal to aid reinstallation.
Caterpillar cat 304.5 mini hydraulic excavator (prefix wak) service repair ma...cdfvvv1
The document provides instructions for disassembling and assembling the swivel on a 304.5 Mini Hydraulic Excavator. The disassembly procedure involves removing 15 fittings and components from the swivel housing including seals, rings, and a flange. The assembly procedure instructs to clean parts, apply oil, and install the components in reverse order, replacing seals and rings as needed. Tools required include retaining ring pliers.
Caterpillar Cat 304.5 Mini Hydraulic Excavator (Prefix WAK) Service Repair Ma...yan77xunhao
This document provides instructions for removing a swing motor from a 304.5 Mini Hydraulic Excavator. The instructions involve releasing hydraulic system pressure, removing the cab and seat, disconnecting linkages from the left console, and removing bolts to detach the right console. Identification marks should be placed on all lines, hoses, wires and tubes before removal to aid reinstallation.
Caterpillar cat 304.5 mini hydraulic excavator (prefix wak) service repair ma...fikskkdmmd1
This document provides instructions for removing a swing motor from a 304.5 Mini Hydraulic Excavator. The steps include releasing hydraulic system pressure, removing the cab and seat, disconnecting linkages from the left console, and removing bolts to detach the right console. Identification marks should be placed on all lines, hoses, wires and tubes before removal to aid reinstallation.
Caterpillar cat 304.5 mini hydraulic excavator (prefix wak) service repair ma...fjskekfseik
This document provides instructions for removing the swing motor from a 304.5 Mini Hydraulic Excavator. The instructions include releasing hydraulic system pressure, removing the cab and seat, disconnecting linkages from the left console, and removing bolts to separate the right console to access the swing motor for removal. Proper containment of fluids and marking of disconnected lines and fittings is emphasized.
Caterpillar Cat 304.5 Mini Hydraulic Excavator (Prefix ANR) Service Repair Ma...tuzhiyou2
The document provides instructions for installing a piston pump on a 304.5 Mini Hydraulic Excavator. It outlines 31 steps to assemble the pump, including installing bearings, seals, plates, blocks, springs, rings and screws. Cleanliness is emphasized throughout the assembly process to prevent contaminants from entering the system. The pump is then installed on the excavator by referring to the installation procedure.
Caterpillar Cat 304.5 Mini Hydraulic Excavator (Prefix ANR) Service Repair Ma...qfyc504378
The document provides instructions for installing a piston pump on a 304.5 Mini Hydraulic Excavator. It outlines 31 steps to assemble the pump, including installing bearings, seals, plates, blocks, springs, rings and screws. Cleanliness is emphasized throughout the assembly process to prevent contaminants from entering the system. The pump is then installed on the excavator by referring to the installation procedure.
Caterpillar Cat 304.5 Mini Hydraulic Excavator (Prefix ANR) Service Repair Ma...lituo39419496
The document provides instructions for disassembling and assembling the piston pump of a 304.5 Mini Hydraulic Excavator. It lists 35 steps to disassemble the pump by removing components like the piston, pump head, springs, and seals. It then lists 32 steps for reassembling the pump by reversing the disassembly process and installing new seals and O-rings. Cleanliness is emphasized throughout to prevent contaminants from entering the system.
Caterpillar Cat 304.5 Mini Hydraulic Excavator (Prefix WAK) Service Repair Ma...jdjkskmikdkmd
This document provides instructions for removing a swing motor from a 304.5 Mini Hydraulic Excavator. The instructions involve releasing hydraulic system pressure, removing the cab and seat, disconnecting linkages from the left console, and removing bolts to detach the right console. Identification marks should be placed on all lines, hoses, wires and tubes before removal to aid reinstallation.
Caterpillar cat 304.5 mini hydraulic excavator (prefix wak) service repair ma...cdfvvv1
The document provides instructions for disassembling and assembling the swivel on a 304.5 Mini Hydraulic Excavator. The disassembly procedure involves removing 15 fittings and components from the swivel housing including seals, rings, and a flange. The assembly procedure instructs to clean parts, apply oil, and install the components in reverse order, replacing seals and rings as needed. Tools required include retaining ring pliers.
Caterpillar Cat 304.5 Mini Hydraulic Excavator (Prefix WAK) Service Repair Ma...yan77xunhao
This document provides instructions for removing a swing motor from a 304.5 Mini Hydraulic Excavator. The instructions involve releasing hydraulic system pressure, removing the cab and seat, disconnecting linkages from the left console, and removing bolts to detach the right console. Identification marks should be placed on all lines, hoses, wires and tubes before removal to aid reinstallation.
Caterpillar cat 304.5 mini hydraulic excavator (prefix wak) service repair ma...fikskkdmmd1
This document provides instructions for removing a swing motor from a 304.5 Mini Hydraulic Excavator. The steps include releasing hydraulic system pressure, removing the cab and seat, disconnecting linkages from the left console, and removing bolts to detach the right console. Identification marks should be placed on all lines, hoses, wires and tubes before removal to aid reinstallation.
Caterpillar cat 304.5 mini hydraulic excavator (prefix wak) service repair ma...fjskekfseik
This document provides instructions for removing the swing motor from a 304.5 Mini Hydraulic Excavator. The instructions include releasing hydraulic system pressure, removing the cab and seat, disconnecting linkages from the left console, and removing bolts to separate the right console to access the swing motor for removal. Proper containment of fluids and marking of disconnected lines and fittings is emphasized.
Caterpillar cat 305 cr mini hydraulic excavator (prefix dsa) service repair m...cdfvvv1
The document provides instructions for removing and disassembling the travel motor from a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing the track and final drive sprocket. Disassembly involves removing plates, barrels, pistons, springs, gears and other components using various tools. Detailed steps and illustrations are provided to label parts and ensure correct reassembly.
Caterpillar Cat 305CR Mini Hydraulic Excavator (Prefix DSA) Service Repair Ma...jdjkskmikdkmd
The document provides instructions for removing and disassembling the travel motor from a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing the track and final drive sprocket. Disassembly involves marking parts, draining oil, removing plates, barrels and pistons. O-rings, seals, gears and other internal components are also dismantled from the motor housing. Detailed illustrations accompany each step for complete disassembly of the travel motor.
Caterpillar Cat 305CR Mini Hydraulic Excavator (Prefix DSA) Service Repair Ma...paws21610697
The document provides instructions for removing and assembling the travel motor on a 305CR Mini Hydraulic Excavator. It details 27 steps to disassemble the travel motor involving removing plates, barrels, pistons, gears, seals, and other components. It then lists 27 steps for reassembling the travel motor, applying sealant and torque specifications where needed and noting the importance of cleanliness during assembly.
Caterpillar Cat 305CR Mini Hydraulic Excavator (Prefix DSA) Service Repair Ma...uddksemd8ud
The document provides instructions for removing and disassembling the travel motor from a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing the track and final drive sprocket. Disassembly involves marking parts, draining oil, removing plates, barrels and pistons. O-rings, seals, gears and other internal components are also dismantled from the motor housing. Detailed illustrations accompany each step for complete disassembly of the travel motor.
Caterpillar Cat 305CR Mini Hydraulic Excavator (Prefix DSA) Service Repair Ma...f7djidksmd3e
The document provides instructions for removing and disassembling the travel motor from a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing the track and final drive sprocket. Disassembly involves marking parts, draining oil, removing plates, barrels and pistons. O-rings, seals, gears and other internal components are also dismantled from the motor housing. Detailed illustrations accompany each step for complete disassembly of the travel motor.
Caterpillar cat 305 cr mini hydraulic excavator (prefix dsa) service repair m...fikskkdmmd1
The document provides instructions for removing and disassembling the travel motor from a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing the track and final drive sprocket. Disassembly involves removing plates, barrels, pistons, springs, gears and other components using various tools. Detailed steps and illustrations are provided to label parts and ensure correct reassembly.
Caterpillar Cat 305CR Mini Hydraulic Excavator (Prefix DSA) Service Repair Ma...yan77xunhao
The document provides instructions for removing and assembling the travel motor on a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing tracks and sprockets, and then disconnecting hoses and removing bolts to take the travel motor off the undercarriage frame. Disassembly of the travel motor includes removing plates, barrels, pistons, gears, shafts, seals and other components. Reassembly follows the reverse order and notes to replace seals, apply oil, and ensure cleanliness.
Caterpillar Cat 305CR Mini Hydraulic Excavator (Prefix DSA) Service Repair Ma...f8usiedkdmm
The document provides instructions for removing and disassembling the travel motor from a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing the track and final drive sprocket. Disassembly involves marking parts, draining oil, removing plates, barrels and pistons. Multiple gears, shafts, seals and other internal components are then dismantled from the travel motor housing.
Caterpillar cat 272 c skid steer loader (prefix red) service repair manual (r...fjjskewerkskem
This document provides disassembly instructions for a piston pump on a 272C skid steer loader. It lists 37 steps to completely disassemble the pump, including removing components like the head assembly, piston assemblies, barrel assembly, shaft assembly, and seals. Special care must be taken when removing springs and releasing spring pressure to avoid injury. Required tools include drivers, pliers, and bearing pullers.
Caterpillar cat 272 c skid steer loader (prefix red) service repair manual (r...fjskkddmmmse
This document provides disassembly instructions for a piston pump on a 272C skid steer loader. It lists 37 steps to fully disassemble the pump, including removing components like the head assembly, piston assemblies, barrel assembly, shaft assembly, and seals. Special care must be taken when removing springs and releasing spring pressure to avoid injury. Required tools include drivers, pliers, and bearing pullers.
Caterpillar cat 272 c skid steer loader (prefix red) service repair manual (r...ufjjsjekdkemme
This document provides disassembly instructions for a piston pump in a 272C skid steer loader. It lists 37 steps to completely disassemble the pump, including removing components like the head assembly, piston assemblies, barrel assembly, shaft assembly, and seals. Special care must be taken when removing springs and releasing spring pressure to avoid injury. Required tools include drivers, pliers, and bearing pullers.
Caterpillar cat 305 cr mini hydraulic excavator (prefix dsa) service repair m...fjskekfseik
The document provides instructions for removing and disassembling the travel motor from a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing the track and final drive sprocket. Disassembly involves marking parts, draining oil, removing plates, barrels and pistons. Multiple gears, shafts, seals and other internal components are then dismantled from the travel motor housing.
Caterpillar Cat W345B Series II Material Handler (Prefix CDY) Service Repair ...paws21610697
This document provides assembly instructions for a swing drive on a W345B Series II wheeled excavator. It includes a list of required tools and 40 steps to assemble the various components of the swing drive, such as bearings, seals, gears, and housings. Special attention is given to cleaning parts, applying lubricants, and torquing bolts to the specified values. The instructions also cover installing the assembled swing drive into the excavator's main frame.
1. Remove the fuel injection pump housing and governor from the engine as a single unit using lifting sling and hoist. Disconnect all connecting lines and tubes.
2. Disassemble the fuel injection pump housing by removing the retaining ring, filter base, tubes and other attached components.
3. Inspect all seals and gaskets, replacing any that are damaged, to prepare the housing for assembly.
This document provides installation instructions for removing and installing an axle shaft on the steering axle of an M325D Material Handler excavator. It is a 15 step process that includes draining fluids, removing bolts and pins, lifting out heavy components using lifting devices, replacing seals and bushings, and reinstalling components in reverse order. Special tools are required and Loctite threadlocker is used on reinstallation.
Caterpillar Cat M325D L MH EXCAVATOR (Prefix KAY) Service Repair Manual (KAY0...paws21610697
This document provides installation instructions for separating an upper frame from an undercarriage frame on an excavator. It outlines 33 steps including removing components like the stick, front and rear drive shafts, swivel, and left boom cylinder. It instructs using tools and lifting devices to reposition pins and plates to separate the frames while supporting heavy components weighing up to 500 pounds. Proper identification of hose and tube assemblies is noted for reinstallation.
Caterpillar Cat M325D L MH EXCAVATOR (Prefix KAY) Service Repair Manual (KAY0...paws21610697
This document provides instructions for disassembling and assembling the swing drive of an M325D L Material Handler excavator. It lists the required tools and presents a 31 step disassembly procedure and a 29 step assembly procedure. The procedures involve removing and installing various components of the swing drive like gears, shafts, bearings, seals and housings. Precautions are provided regarding cleanliness and safety.
The document provides instructions for disassembling the front and rear final drive carriers, hubs, and brakes of an M320 excavator. The 28 step procedure describes how to remove components like planetary carriers, sun gears, ring gears, brake pistons, bearings, and seals. Tools required include retaining ring pliers, pullers, wrenches, and hammers. Safety notices are provided to release hydraulic pressure and contain fluids before disassembly.
This document provides instructions for disassembling and assembling the rear axle carrier, hubs, and brakes of an M318F wheeled excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for removing components like the carrier housing, planetary gears, and brake discs, and installing components like the thrust washer, carrier gear, and retaining rings. The instructions aim to properly remove and replace these components while containing fluids and following safety procedures.
This document provides instructions for disassembling and assembling the rear axle carrier, hubs, and brakes of an M317F wheeled excavator. The disassembly procedure involves removing 23 components including carrier housing, planetary gears, thrust washers, retaining rings, and hub. The assembly procedure provides steps to install 23 components in reverse order and includes checking brake clearance and installing seals and bearings. Tools required include retaining ring pliers, drivers, spanners, pry bars, pullers, and torque wrenches.
The document provides instructions for removing and installing various components on a M317D2 Wheeled Excavator, including:
- Removing the swing gear and bearing by lifting it out after removing bolts and spacers.
- Installing the swing gear and bearing by positioning it with lifting tools, then installing bolts and spacers.
- Removing the hydraulic oil filter by taking off the cover, O-ring, and retainer, then removing the filter.
- Installing the hydraulic oil filter by reversing the removal steps.
- Removing the hydraulic tank by draining it, disconnecting hoses and fittings, and lifting it off after removing bolts.
- Installing the hydraulic tank by
The document provides instructions for disassembling and assembling the main hydraulic pump of a M317D2 Wheeled Excavator. It lists 34 steps for disassembly, removing components like pistons, springs, seals and bearings. It then lists 36 steps for assembly, replacing components and using various tools to set dimensions and install retaining rings, seals and bearings. Precision is required to mark positions of parts and reinstall components in their original orientation for proper function.
More Related Content
Similar to Caterpillar Cat 304.5 Mini Hydraulic Excavator (Prefix ANR) Service Repair Manual (ANR00001 and up).pdf
Caterpillar cat 305 cr mini hydraulic excavator (prefix dsa) service repair m...cdfvvv1
The document provides instructions for removing and disassembling the travel motor from a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing the track and final drive sprocket. Disassembly involves removing plates, barrels, pistons, springs, gears and other components using various tools. Detailed steps and illustrations are provided to label parts and ensure correct reassembly.
Caterpillar Cat 305CR Mini Hydraulic Excavator (Prefix DSA) Service Repair Ma...jdjkskmikdkmd
The document provides instructions for removing and disassembling the travel motor from a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing the track and final drive sprocket. Disassembly involves marking parts, draining oil, removing plates, barrels and pistons. O-rings, seals, gears and other internal components are also dismantled from the motor housing. Detailed illustrations accompany each step for complete disassembly of the travel motor.
Caterpillar Cat 305CR Mini Hydraulic Excavator (Prefix DSA) Service Repair Ma...paws21610697
The document provides instructions for removing and assembling the travel motor on a 305CR Mini Hydraulic Excavator. It details 27 steps to disassemble the travel motor involving removing plates, barrels, pistons, gears, seals, and other components. It then lists 27 steps for reassembling the travel motor, applying sealant and torque specifications where needed and noting the importance of cleanliness during assembly.
Caterpillar Cat 305CR Mini Hydraulic Excavator (Prefix DSA) Service Repair Ma...uddksemd8ud
The document provides instructions for removing and disassembling the travel motor from a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing the track and final drive sprocket. Disassembly involves marking parts, draining oil, removing plates, barrels and pistons. O-rings, seals, gears and other internal components are also dismantled from the motor housing. Detailed illustrations accompany each step for complete disassembly of the travel motor.
Caterpillar Cat 305CR Mini Hydraulic Excavator (Prefix DSA) Service Repair Ma...f7djidksmd3e
The document provides instructions for removing and disassembling the travel motor from a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing the track and final drive sprocket. Disassembly involves marking parts, draining oil, removing plates, barrels and pistons. O-rings, seals, gears and other internal components are also dismantled from the motor housing. Detailed illustrations accompany each step for complete disassembly of the travel motor.
Caterpillar cat 305 cr mini hydraulic excavator (prefix dsa) service repair m...fikskkdmmd1
The document provides instructions for removing and disassembling the travel motor from a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing the track and final drive sprocket. Disassembly involves removing plates, barrels, pistons, springs, gears and other components using various tools. Detailed steps and illustrations are provided to label parts and ensure correct reassembly.
Caterpillar Cat 305CR Mini Hydraulic Excavator (Prefix DSA) Service Repair Ma...yan77xunhao
The document provides instructions for removing and assembling the travel motor on a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing tracks and sprockets, and then disconnecting hoses and removing bolts to take the travel motor off the undercarriage frame. Disassembly of the travel motor includes removing plates, barrels, pistons, gears, shafts, seals and other components. Reassembly follows the reverse order and notes to replace seals, apply oil, and ensure cleanliness.
Caterpillar Cat 305CR Mini Hydraulic Excavator (Prefix DSA) Service Repair Ma...f8usiedkdmm
The document provides instructions for removing and disassembling the travel motor from a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing the track and final drive sprocket. Disassembly involves marking parts, draining oil, removing plates, barrels and pistons. Multiple gears, shafts, seals and other internal components are then dismantled from the travel motor housing.
Caterpillar cat 272 c skid steer loader (prefix red) service repair manual (r...fjjskewerkskem
This document provides disassembly instructions for a piston pump on a 272C skid steer loader. It lists 37 steps to completely disassemble the pump, including removing components like the head assembly, piston assemblies, barrel assembly, shaft assembly, and seals. Special care must be taken when removing springs and releasing spring pressure to avoid injury. Required tools include drivers, pliers, and bearing pullers.
Caterpillar cat 272 c skid steer loader (prefix red) service repair manual (r...fjskkddmmmse
This document provides disassembly instructions for a piston pump on a 272C skid steer loader. It lists 37 steps to fully disassemble the pump, including removing components like the head assembly, piston assemblies, barrel assembly, shaft assembly, and seals. Special care must be taken when removing springs and releasing spring pressure to avoid injury. Required tools include drivers, pliers, and bearing pullers.
Caterpillar cat 272 c skid steer loader (prefix red) service repair manual (r...ufjjsjekdkemme
This document provides disassembly instructions for a piston pump in a 272C skid steer loader. It lists 37 steps to completely disassemble the pump, including removing components like the head assembly, piston assemblies, barrel assembly, shaft assembly, and seals. Special care must be taken when removing springs and releasing spring pressure to avoid injury. Required tools include drivers, pliers, and bearing pullers.
Caterpillar cat 305 cr mini hydraulic excavator (prefix dsa) service repair m...fjskekfseik
The document provides instructions for removing and disassembling the travel motor from a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing the track and final drive sprocket. Disassembly involves marking parts, draining oil, removing plates, barrels and pistons. Multiple gears, shafts, seals and other internal components are then dismantled from the travel motor housing.
Similar to Caterpillar Cat 304.5 Mini Hydraulic Excavator (Prefix ANR) Service Repair Manual (ANR00001 and up).pdf (12)
Caterpillar Cat W345B Series II Material Handler (Prefix CDY) Service Repair ...paws21610697
This document provides assembly instructions for a swing drive on a W345B Series II wheeled excavator. It includes a list of required tools and 40 steps to assemble the various components of the swing drive, such as bearings, seals, gears, and housings. Special attention is given to cleaning parts, applying lubricants, and torquing bolts to the specified values. The instructions also cover installing the assembled swing drive into the excavator's main frame.
1. Remove the fuel injection pump housing and governor from the engine as a single unit using lifting sling and hoist. Disconnect all connecting lines and tubes.
2. Disassemble the fuel injection pump housing by removing the retaining ring, filter base, tubes and other attached components.
3. Inspect all seals and gaskets, replacing any that are damaged, to prepare the housing for assembly.
This document provides installation instructions for removing and installing an axle shaft on the steering axle of an M325D Material Handler excavator. It is a 15 step process that includes draining fluids, removing bolts and pins, lifting out heavy components using lifting devices, replacing seals and bushings, and reinstalling components in reverse order. Special tools are required and Loctite threadlocker is used on reinstallation.
Caterpillar Cat M325D L MH EXCAVATOR (Prefix KAY) Service Repair Manual (KAY0...paws21610697
This document provides installation instructions for separating an upper frame from an undercarriage frame on an excavator. It outlines 33 steps including removing components like the stick, front and rear drive shafts, swivel, and left boom cylinder. It instructs using tools and lifting devices to reposition pins and plates to separate the frames while supporting heavy components weighing up to 500 pounds. Proper identification of hose and tube assemblies is noted for reinstallation.
Caterpillar Cat M325D L MH EXCAVATOR (Prefix KAY) Service Repair Manual (KAY0...paws21610697
This document provides instructions for disassembling and assembling the swing drive of an M325D L Material Handler excavator. It lists the required tools and presents a 31 step disassembly procedure and a 29 step assembly procedure. The procedures involve removing and installing various components of the swing drive like gears, shafts, bearings, seals and housings. Precautions are provided regarding cleanliness and safety.
The document provides instructions for disassembling the front and rear final drive carriers, hubs, and brakes of an M320 excavator. The 28 step procedure describes how to remove components like planetary carriers, sun gears, ring gears, brake pistons, bearings, and seals. Tools required include retaining ring pliers, pullers, wrenches, and hammers. Safety notices are provided to release hydraulic pressure and contain fluids before disassembly.
This document provides instructions for disassembling and assembling the rear axle carrier, hubs, and brakes of an M318F wheeled excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for removing components like the carrier housing, planetary gears, and brake discs, and installing components like the thrust washer, carrier gear, and retaining rings. The instructions aim to properly remove and replace these components while containing fluids and following safety procedures.
This document provides instructions for disassembling and assembling the rear axle carrier, hubs, and brakes of an M317F wheeled excavator. The disassembly procedure involves removing 23 components including carrier housing, planetary gears, thrust washers, retaining rings, and hub. The assembly procedure provides steps to install 23 components in reverse order and includes checking brake clearance and installing seals and bearings. Tools required include retaining ring pliers, drivers, spanners, pry bars, pullers, and torque wrenches.
The document provides instructions for removing and installing various components on a M317D2 Wheeled Excavator, including:
- Removing the swing gear and bearing by lifting it out after removing bolts and spacers.
- Installing the swing gear and bearing by positioning it with lifting tools, then installing bolts and spacers.
- Removing the hydraulic oil filter by taking off the cover, O-ring, and retainer, then removing the filter.
- Installing the hydraulic oil filter by reversing the removal steps.
- Removing the hydraulic tank by draining it, disconnecting hoses and fittings, and lifting it off after removing bolts.
- Installing the hydraulic tank by
The document provides instructions for disassembling and assembling the main hydraulic pump of a M317D2 Wheeled Excavator. It lists 34 steps for disassembly, removing components like pistons, springs, seals and bearings. It then lists 36 steps for assembly, replacing components and using various tools to set dimensions and install retaining rings, seals and bearings. Precision is required to mark positions of parts and reinstall components in their original orientation for proper function.
This document provides instructions for disassembling and assembling a swing drive on a wheeled excavator model M316D. The removal procedure involves releasing hydraulic pressure, removing hoses and bolts, and using lifting tools to remove the swing drive assembly. The disassembly procedure then describes using various tools to remove retaining rings, plates, discs, seals, gears, and other internal components. The assembly procedure outlines cleaning and lubricating parts, and using tools to reinstall components in reverse order, taking care to properly seat bearings and tighten nuts to the specified torques.
The document provides instructions for disassembling the front and rear axles of an M315F wheeled excavator. It lists required tools and presents a 23 step procedure for removing components like carrier housings, planetary gears, bearings, seals, and hubs. Detailed illustrations accompany each step to show how to properly disassemble parts. Safety notices are included to handle fluids and springs safely during the process.
The document provides disassembly and assembly instructions for the travel motor of an M312 excavator. It lists 44 steps to disassemble the travel motor and its components. These include removing covers, gaskets, seals, valves, springs, pins, and other parts. It then lists the assembly steps in reverse order, noting to replace all seals and gaskets, apply oil, and ensure cleanliness during assembly.
Caterpillar Cat M312 Excavator (Prefix 6TL) Service Repair Manual (6TL00001-0...paws21610697
This document provides the disassembly and assembly procedures for the swing drive of an M312 excavator. The disassembly procedure involves 28 steps to remove components such as the swing brake assembly, discs, plates, piston, seals, shaft, gears, bearings, and housing. The assembly procedure involves 17 steps and requires various tools to install components in the reverse order of disassembly while applying lubricant and ensuring proper torque specifications are achieved.
This document provides instructions for removing and installing engine oil filter bases and related components on Caterpillar 3304B and 3306B engines. The procedures describe removing the oil filter, oil filter base, gaskets and O-rings. Instructions are provided for disassembling the oil filter base by removing covers, bolts, springs and plungers. Reassembly and installation steps are also outlined. Tools required are listed for each procedure. Precautions are noted to keep parts clean and contain fluids.
Caterpillar Cat D250E II Articulated Truck (Prefix 4PS) Service Repair Manual...paws21610697
The document provides instructions for disassembling and assembling the piston pump used for steering on a D250E II Articulated Truck. The disassembly procedure involves removing 21 individual parts from the pump housing. The assembly procedure instructs assembling the 21 parts in the reverse order, applying lubrication and torque specifications as needed. Tools required include various drivers, pliers, and lubricants.
The document provides instructions for disassembling and assembling the governor of an articulated truck. It lists 57 steps to disassemble the front and rear housings of the governor. Tools required include a governor repair fixture, retaining ring pliers, pin punch, clevis driver, and legs to mount the rear housing. Cautions are provided regarding cleaning parts and containing fluids during maintenance.
The document provides instructions for disassembling and assembling a Type I governor used in Caterpillar 3114, 3116, and 3126 engines. It describes 35 steps to disassemble the governor front housing and 19 additional steps to disassemble the rear housing. Various parts are inspected for wear or damage during disassembly. Cleaning and replacement parts are also discussed. Tools required are listed.
The document provides instructions for removing and installing various engine components on a Caterpillar 3408 industrial engine, including the oil cooler, oil filter base, oil bypass valves, engine oil cooler/lines, aftercooler, and turbocharger. The procedures describe removing bolts, hoses, seals, and other parts, cleaning components, applying sealant, and reinstalling parts in reverse order.
The document provides instructions for removing and installing wheel spindles on Caterpillar articulated dump trucks. It describes removing the wheels, bearings, and seals before removing the brake shoes. It then details removing pins and springs to separate the brake shoes from the spider. Reinstallation follows the reverse order. Instructions are also given for disassembling and assembling suspension cylinders.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
2. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 304.5 MINI HYD EXCAVATOR ANR
Configuration: 304.5 Mini Hydraulic Excavator ANR00001-UP (MACHINE) POWERED BY 3024 Engine
Disassembly and Assembly
304.5 Mini Hydraulic Excavator Machine Systems
Media Number -RENR3548-04 Publication Date -01/08/2008 Date Updated -18/08/2008
i01368358
Piston Pump - Disassemble
SMCS - 5070-015
Disassembly Procedure
Table 1
REQUIRED TOOLS
Tool Part Number Part Description Qty
A 1P-1857 Snap Ring Pliers 1
B 1P-1859 Snap Ring Pliers 1
Start By:
A. Remove the piston pump. Refer to Disassembly and Assembly, "Piston Pump - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/9
304.5 Mini Hydraulic Excavator ANR00001-UP (MACHINE) POWERED BY 3024 E...
2020/2/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Note: Put identification marks on the pump and on all lines for installation purposes. Plug all
lines. This will help to prevent fluid loss and this helps to keep contaminants from entering the
system.
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
Illustration 1 g00722015
1. Remove allen head screw (1) .
2. Remove hub (2) from the shaft.
Illustration 2 g00721949
3. Remove collar (3) from the pump head.
4. Remove coupling (4) from the pump head.
5. Remove O-ring (5) from the pump head.
Note: Do not remove large allen head screw on valve (7).
2/9
304.5 Mini Hydraulic Excavator ANR00001-UP (MACHINE) POWERED BY 3024 E...
2020/2/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g00722021
6. Remove two allen head screws (6) from the valve.
7. Remove valve (7) .
Illustration 4 g00722028
Illustration 5 g00722037
3/9
304.5 Mini Hydraulic Excavator ANR00001-UP (MACHINE) POWERED BY 3024 E...
2020/2/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 8. Remove piston (8) from the pump head.
9. Remove O-ring (9) from piston (8) .
Note: One allen head screw (10) is longer than the other three allen head screws.
Illustration 6 g00722043
10. Remove four allen head screws (10) .
11. Remove pump head (11) from the pump body.
Illustration 7 g00722051
12. Rotate the pump head to the other side.
13. Remove O-ring (12) from the pump head.
14. Remove four O-rings (13) from the pump head.
15. Remove plate (14) from the pump head.
4/9
304.5 Mini Hydraulic Excavator ANR00001-UP (MACHINE) POWERED BY 3024 E...
2020/2/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 8 g00722064
16. Remove two allen head screws (15) from the piston block.
17. Remove piston block (16) from the pump head.
Illustration 9 g00722086
18. Remove O-rings (17), (18), and (19) from the piston block.
Illustration 10 g00722089
5/9
304.5 Mini Hydraulic Excavator ANR00001-UP (MACHINE) POWERED BY 3024 E...
2020/2/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 19. Remove springs (20) and (21) from the pump body.
20. Use Tooling (A) to remove snap ring (22) .
21. Remove pump rotating group (23) from the shaft.
Illustration 11 g00722106
22. Remove spring retainer (24) from the swashplate.
Illustration 12 g00722113
23. Remove four allen head screws (25) from plate (26) .
24. Remove plate (26) from the pump body.
6/9
304.5 Mini Hydraulic Excavator ANR00001-UP (MACHINE) POWERED BY 3024 E...
2020/2/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 13 g00722120
25. Rotate plate (26) to the other side.
26. Remove O-ring (27) from the plate.
Illustration 14 g00722384
27. Remove valve assembly (28) from the pump body.
7/9
304.5 Mini Hydraulic Excavator ANR00001-UP (MACHINE) POWERED BY 3024 E...
2020/2/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 15 g00722149
28. Use Tooling (B) to remove snap ring (29) from the pump body.
29. Remove plate (30) from shaft (31) .
30. Remove shaft (31) from the pump body.
Illustration 16 g00722209
31. Rotate plate (30) to the other side.
32. Remove O-ring (32) from the plate.
33. Remove O-ring seal (33) from the plate.
8/9
304.5 Mini Hydraulic Excavator ANR00001-UP (MACHINE) POWERED BY 3024 E...
2020/2/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 17 g00722214
34. Use Tooling (A) to remove two snap rings (34) from shaft (31) .
35. Remove bearing (35) from shaft (31) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Feb 21 23:29:23 UTC+0800 2020
9/9
304.5 Mini Hydraulic Excavator ANR00001-UP (MACHINE) POWERED BY 3024 E...
2020/2/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 304.5 MINI HYD EXCAVATOR ANR
Configuration: 304.5 Mini Hydraulic Excavator ANR00001-UP (MACHINE) POWERED BY 3024 Engine
Disassembly and Assembly
304.5 Mini Hydraulic Excavator Machine Systems
Media Number -RENR3548-04 Publication Date -01/08/2008 Date Updated -18/08/2008
i01369293
Piston Pump - Assemble
SMCS - 5070-016
Assembly Procedure
Table 1
REQUIRED TOOLS
Tool Part Number Part Description Qty
A 1P-1857 Snap Ring Pliers 1
B 1P-1859 Snap Ring Pliers 1
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Note: Cleanliness is an important factor. Before the assembly procedure, the interior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
1/9
304.5 Mini Hydraulic Excavator ANR00001-UP (MACHINE) POWERED BY 3024 E...
2020/2/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 1 g00722214
1. Install bearing (35) onto shaft (31) .
2. Use Tooling (A) to install two snap rings (34) onto shaft (31) .
Illustration 2 g00722209
3. Install a new O-ring seal (33) into plate (30) .
4. Install a new O-ring (32) to plate (30) .
2/9
304.5 Mini Hydraulic Excavator ANR00001-UP (MACHINE) POWERED BY 3024 E...
2020/2/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 3 g00722149
5. Position shaft assembly (31) into the pump housing.
6. Install plate (30) onto shaft (31) and the pump housing.
7. Use Tooling (B) to install snap ring (29) onto shaft (31) .
Illustration 4 g00722384
8. Install valve assembly (28) to the pump body.
3/9
304.5 Mini Hydraulic Excavator ANR00001-UP (MACHINE) POWERED BY 3024 E...
2020/2/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 5 g00722120
9. Install a new O-ring (27) to plate (26) .
Illustration 6 g00722113
10. Place plate (26) to the pump housing.
11. Install four allen head screws (25) to plate (26). Tighten the allen head screws to a torque of
12 ± 3 N·m (9 ± 2 lb ft).
4/9
304.5 Mini Hydraulic Excavator ANR00001-UP (MACHINE) POWERED BY 3024 E...
2020/2/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 7 g00722106
12. Place spring retainer (24) to the swashplate.
Illustration 8 g00722089
13. Install pump rotating group (23) onto the shaft.
14. Use Tooling (A) to install snap ring (22) onto the shaft.
15. Install springs (21) and (20) into the pump housing.
Illustration 9 g00722086
16. Install new O-rings (17) , (18), and (19) onto the piston block.
5/9
304.5 Mini Hydraulic Excavator ANR00001-UP (MACHINE) POWERED BY 3024 E...
2020/2/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 10 g00722064
17. Place piston block (16) on the pump head.
18. Install two allen head screws (15) to piston block (16) .
Illustration 11 g00722051
19. Install plate (14) to the pump head.
20. Install four new O-rings (13) to the pump head.
21. Install a new O-ring (12) to the pump head.
6/9
304.5 Mini Hydraulic Excavator ANR00001-UP (MACHINE) POWERED BY 3024 E...
2020/2/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 12 g00722043
22. Place pump head (11) onto the pump body.
23. Install four allen head screws (10) to pump head (11). Tighten the allen head screws to a
torque of 55 ± 14 N·m (41 ± 10 lb ft).
Illustration 13 g00722037
Illustration 14 g00722028
7/9
304.5 Mini Hydraulic Excavator ANR00001-UP (MACHINE) POWERED BY 3024 E...
2020/2/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. 24. Install a new O-ring (9) onto piston (8) .
25. Install piston (8) into the pump head.
Illustration 15 g00722021
26. Place valve (7) on the pump head.
27. Install two allen head screws (6) to the valve.
Illustration 16 g00721949
28. Install a new O-ring (5) to the pump head.
29. Install coupling (4) into the pump head.
30. Install collar (3) into the pump head.
8/9
304.5 Mini Hydraulic Excavator ANR00001-UP (MACHINE) POWERED BY 3024 E...
2020/2/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 17 g00722015
31. Install hub (2) onto the shaft.
32. Install allen head screw (1) to hub (2). Hub (2) must be installed against the shoulder of the
shaft. Tighten the allen head screw to a torque of 49 ± 9 N·m (36 ± 7 lb ft).
End By: Install the piston pump. Refer to Disassembly and Assembly, "Piston Pump - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Feb 21 23:30:20 UTC+0800 2020
9/9
304.5 Mini Hydraulic Excavator ANR00001-UP (MACHINE) POWERED BY 3024 E...
2020/2/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 304.5 MINI HYD EXCAVATOR ANR
Configuration: 304.5 Mini Hydraulic Excavator ANR00001-UP (MACHINE) POWERED BY 3024 Engine
Disassembly and Assembly
304.5 Mini Hydraulic Excavator Machine Systems
Media Number -RENR3548-04 Publication Date -01/08/2008 Date Updated -18/08/2008
i01348698
Piston Pump - Install
SMCS - 5070-012
Installation Procedure
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/6
304.5 Mini Hydraulic Excavator ANR00001-UP (MACHINE) POWERED BY 3024 E...
2020/2/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
22. Illustration 1 g00711747
1. Use a suitable lifting device to support the piston pump (10) in place. Weight of the piston
pump is 27 kg (60 lb).
Illustration 2 g00711740
2. Install the piston pump to the engine with a suitable lifting device.
3. Install washers and two bolts (9).
2/6
304.5 Mini Hydraulic Excavator ANR00001-UP (MACHINE) POWERED BY 3024 E...
2020/2/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 3 g00711728
Illustration 4 g00711880
4. Install a new O-ring (8) .
5. Install washers and four bolts (7) .
Illustration 5 g00711727
6. Connect lines (5) and (6) to the piston pump.
3/6
304.5 Mini Hydraulic Excavator ANR00001-UP (MACHINE) POWERED BY 3024 E...
2020/2/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 6 g00711725
7. Position left rear support assembly (4) .
8. Install washers and four bolts (3) .
Illustration 7 g00711720
Illustration 8 g00711712
4/6
304.5 Mini Hydraulic Excavator ANR00001-UP (MACHINE) POWERED BY 3024 E...
2020/2/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...