The documents provide instructions for removing and installing various components on a 301.8 Mini Hydraulic Excavator, including the blade, bucket, bucket linkage, and bucket cylinder. The procedures describe disconnecting hoses, removing bolts and pins, lifting components, and installing components in the reverse order of removal while taking safety precautions for working with pressurized hydraulic systems.
Caterpillar cat 301.6 mini hydraulic excavator (prefix my6) service repair ma...fjsjekdmmeme
The document provides instructions for disassembling and assembling a blade cylinder for a 301.6 Mini Hydraulic Excavator. The disassembly procedure involves removing seals and other components from both ends of the cylinder. The assembly procedure describes installing the components in reverse order and applying the appropriate torque to fasteners. Separate sections also describe removing and installing the excavator's blade and bucket.
Caterpillar cat 301.6 mini hydraulic excavator (prefix my6) service repair ma...fjskekfseik
The document provides instructions for disassembling and assembling a blade cylinder for a 301.6 Mini Hydraulic Excavator. The disassembly procedure involves removing seals and other components from both ends of the cylinder. The assembly procedure describes installing the components in reverse order and applying the appropriate torque to fasteners. Separate sections also describe removing and installing the excavator's blade and bucket.
Caterpillar Cat 301.6 Mini Hydraulic Excavator (Prefix MY6) Service Repair Ma...udjkskdmmd
The document provides instructions for removing and installing a bucket on a 301.6 Mini Hydraulic Excavator. The removal procedure involves lowering the bucket to the ground, removing retainer bolts, and removing pins from the bucket linkage and stick to detach the bucket. The installation procedure is the reverse of removal, positioning the stick over the bucket and installing pins and retainer bolts.
Caterpillar cat 301.6 mini hydraulic excavator (prefix my6) service repair ma...fikskkdmmd1
The document provides instructions for disassembling and assembling a blade cylinder for a 301.6 Mini Hydraulic Excavator. The disassembly procedure involves removing seals and other components from both ends of the cylinder. The assembly procedure describes installing the components in reverse order and applying the appropriate torque to fasteners. Separate sections also describe removing and installing the excavator's blade and bucket.
Caterpillar Cat 301.6 Mini Hydraulic Excavator (Prefix MY6) Service Repair Ma...yan77xunhao
The document provides instructions for removing and installing a bucket on a 301.6 Mini Hydraulic Excavator. The removal procedure involves lowering the bucket to the ground, removing retainer bolts and pins connecting the bucket to the linkage and stick, and removing the bucket. The installation procedure is the reverse of removal, positioning the stick over the bucket and installing the pins and retainer bolts.
Caterpillar cat 301.7 cr mini hydraulic excavator (prefix jh7) service repair...fjskekfseik
The document provides instructions for disassembling and assembling the boom cylinder of a Caterpillar 301.7CR Mini Hydraulic Excavator. The disassembly procedure involves removing seals and internal components from both ends of the cylinder. The assembly procedure describes installing seals and components in the reverse order of disassembly. Tools required include a cylinder repair bench, spanner wrenches, and sockets. Safety precautions are provided regarding hydraulic pressure during disassembly.
Caterpillar cat 301.7 cr mini hydraulic excavator (prefix jh7) service repair...fjsjekdmmeme
The document provides instructions for disassembling and assembling the boom cylinder of a Caterpillar 301.7CR Mini Hydraulic Excavator. The disassembly procedure involves removing seals and internal components from both ends of the cylinder. The assembly procedure describes installing these components in reverse order. Separate sections also describe removing and installing the entire boom and boom swing cylinder. Safety precautions are provided regarding hydraulic pressure during maintenance.
Caterpillar cat 301.7 cr mini hydraulic excavator (prefix jh7) service repair...fikskkdmmd1
The document provides instructions for disassembling and assembling the boom cylinder of a 301.7CR mini hydraulic excavator. The disassembly procedure involves removing seals and mounting the cylinder in a repair bench tool to access internal components like the piston. Items like seals, bushings, and O-rings are then removed. The assembly procedure reverses these steps, providing details on installing individual parts and tightening to the specified torques. Tools required include a cylinder repair bench, spanner wrenches, and sockets.
Caterpillar cat 301.6 mini hydraulic excavator (prefix my6) service repair ma...fjsjekdmmeme
The document provides instructions for disassembling and assembling a blade cylinder for a 301.6 Mini Hydraulic Excavator. The disassembly procedure involves removing seals and other components from both ends of the cylinder. The assembly procedure describes installing the components in reverse order and applying the appropriate torque to fasteners. Separate sections also describe removing and installing the excavator's blade and bucket.
Caterpillar cat 301.6 mini hydraulic excavator (prefix my6) service repair ma...fjskekfseik
The document provides instructions for disassembling and assembling a blade cylinder for a 301.6 Mini Hydraulic Excavator. The disassembly procedure involves removing seals and other components from both ends of the cylinder. The assembly procedure describes installing the components in reverse order and applying the appropriate torque to fasteners. Separate sections also describe removing and installing the excavator's blade and bucket.
Caterpillar Cat 301.6 Mini Hydraulic Excavator (Prefix MY6) Service Repair Ma...udjkskdmmd
The document provides instructions for removing and installing a bucket on a 301.6 Mini Hydraulic Excavator. The removal procedure involves lowering the bucket to the ground, removing retainer bolts, and removing pins from the bucket linkage and stick to detach the bucket. The installation procedure is the reverse of removal, positioning the stick over the bucket and installing pins and retainer bolts.
Caterpillar cat 301.6 mini hydraulic excavator (prefix my6) service repair ma...fikskkdmmd1
The document provides instructions for disassembling and assembling a blade cylinder for a 301.6 Mini Hydraulic Excavator. The disassembly procedure involves removing seals and other components from both ends of the cylinder. The assembly procedure describes installing the components in reverse order and applying the appropriate torque to fasteners. Separate sections also describe removing and installing the excavator's blade and bucket.
Caterpillar Cat 301.6 Mini Hydraulic Excavator (Prefix MY6) Service Repair Ma...yan77xunhao
The document provides instructions for removing and installing a bucket on a 301.6 Mini Hydraulic Excavator. The removal procedure involves lowering the bucket to the ground, removing retainer bolts and pins connecting the bucket to the linkage and stick, and removing the bucket. The installation procedure is the reverse of removal, positioning the stick over the bucket and installing the pins and retainer bolts.
Caterpillar cat 301.7 cr mini hydraulic excavator (prefix jh7) service repair...fjskekfseik
The document provides instructions for disassembling and assembling the boom cylinder of a Caterpillar 301.7CR Mini Hydraulic Excavator. The disassembly procedure involves removing seals and internal components from both ends of the cylinder. The assembly procedure describes installing seals and components in the reverse order of disassembly. Tools required include a cylinder repair bench, spanner wrenches, and sockets. Safety precautions are provided regarding hydraulic pressure during disassembly.
Caterpillar cat 301.7 cr mini hydraulic excavator (prefix jh7) service repair...fjsjekdmmeme
The document provides instructions for disassembling and assembling the boom cylinder of a Caterpillar 301.7CR Mini Hydraulic Excavator. The disassembly procedure involves removing seals and internal components from both ends of the cylinder. The assembly procedure describes installing these components in reverse order. Separate sections also describe removing and installing the entire boom and boom swing cylinder. Safety precautions are provided regarding hydraulic pressure during maintenance.
Caterpillar cat 301.7 cr mini hydraulic excavator (prefix jh7) service repair...fikskkdmmd1
The document provides instructions for disassembling and assembling the boom cylinder of a 301.7CR mini hydraulic excavator. The disassembly procedure involves removing seals and mounting the cylinder in a repair bench tool to access internal components like the piston. Items like seals, bushings, and O-rings are then removed. The assembly procedure reverses these steps, providing details on installing individual parts and tightening to the specified torques. Tools required include a cylinder repair bench, spanner wrenches, and sockets.
Caterpillar Cat W345B Series II Material Handler (Prefix CDY) Service Repair ...paws21610697
This document provides assembly instructions for a swing drive on a W345B Series II wheeled excavator. It includes a list of required tools and 40 steps to assemble the various components of the swing drive, such as bearings, seals, gears, and housings. Special attention is given to cleaning parts, applying lubricants, and torquing bolts to the specified values. The instructions also cover installing the assembled swing drive into the excavator's main frame.
1. Remove the fuel injection pump housing and governor from the engine as a single unit using lifting sling and hoist. Disconnect all connecting lines and tubes.
2. Disassemble the fuel injection pump housing by removing the retaining ring, filter base, tubes and other attached components.
3. Inspect all seals and gaskets, replacing any that are damaged, to prepare the housing for assembly.
This document provides installation instructions for removing and installing an axle shaft on the steering axle of an M325D Material Handler excavator. It is a 15 step process that includes draining fluids, removing bolts and pins, lifting out heavy components using lifting devices, replacing seals and bushings, and reinstalling components in reverse order. Special tools are required and Loctite threadlocker is used on reinstallation.
Caterpillar Cat M325D L MH EXCAVATOR (Prefix KAY) Service Repair Manual (KAY0...paws21610697
This document provides installation instructions for separating an upper frame from an undercarriage frame on an excavator. It outlines 33 steps including removing components like the stick, front and rear drive shafts, swivel, and left boom cylinder. It instructs using tools and lifting devices to reposition pins and plates to separate the frames while supporting heavy components weighing up to 500 pounds. Proper identification of hose and tube assemblies is noted for reinstallation.
Caterpillar Cat M325D L MH EXCAVATOR (Prefix KAY) Service Repair Manual (KAY0...paws21610697
This document provides instructions for disassembling and assembling the swing drive of an M325D L Material Handler excavator. It lists the required tools and presents a 31 step disassembly procedure and a 29 step assembly procedure. The procedures involve removing and installing various components of the swing drive like gears, shafts, bearings, seals and housings. Precautions are provided regarding cleanliness and safety.
The document provides instructions for disassembling the front and rear final drive carriers, hubs, and brakes of an M320 excavator. The 28 step procedure describes how to remove components like planetary carriers, sun gears, ring gears, brake pistons, bearings, and seals. Tools required include retaining ring pliers, pullers, wrenches, and hammers. Safety notices are provided to release hydraulic pressure and contain fluids before disassembly.
This document provides instructions for disassembling and assembling the rear axle carrier, hubs, and brakes of an M318F wheeled excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for removing components like the carrier housing, planetary gears, and brake discs, and installing components like the thrust washer, carrier gear, and retaining rings. The instructions aim to properly remove and replace these components while containing fluids and following safety procedures.
This document provides instructions for disassembling and assembling the rear axle carrier, hubs, and brakes of an M317F wheeled excavator. The disassembly procedure involves removing 23 components including carrier housing, planetary gears, thrust washers, retaining rings, and hub. The assembly procedure provides steps to install 23 components in reverse order and includes checking brake clearance and installing seals and bearings. Tools required include retaining ring pliers, drivers, spanners, pry bars, pullers, and torque wrenches.
The document provides instructions for removing and installing various components on a M317D2 Wheeled Excavator, including:
- Removing the swing gear and bearing by lifting it out after removing bolts and spacers.
- Installing the swing gear and bearing by positioning it with lifting tools, then installing bolts and spacers.
- Removing the hydraulic oil filter by taking off the cover, O-ring, and retainer, then removing the filter.
- Installing the hydraulic oil filter by reversing the removal steps.
- Removing the hydraulic tank by draining it, disconnecting hoses and fittings, and lifting it off after removing bolts.
- Installing the hydraulic tank by
The document provides instructions for disassembling and assembling the main hydraulic pump of a M317D2 Wheeled Excavator. It lists 34 steps for disassembly, removing components like pistons, springs, seals and bearings. It then lists 36 steps for assembly, replacing components and using various tools to set dimensions and install retaining rings, seals and bearings. Precision is required to mark positions of parts and reinstall components in their original orientation for proper function.
This document provides instructions for disassembling and assembling a swing drive on a wheeled excavator model M316D. The removal procedure involves releasing hydraulic pressure, removing hoses and bolts, and using lifting tools to remove the swing drive assembly. The disassembly procedure then describes using various tools to remove retaining rings, plates, discs, seals, gears, and other internal components. The assembly procedure outlines cleaning and lubricating parts, and using tools to reinstall components in reverse order, taking care to properly seat bearings and tighten nuts to the specified torques.
The document provides instructions for disassembling the front and rear axles of an M315F wheeled excavator. It lists required tools and presents a 23 step procedure for removing components like carrier housings, planetary gears, bearings, seals, and hubs. Detailed illustrations accompany each step to show how to properly disassemble parts. Safety notices are included to handle fluids and springs safely during the process.
The document provides disassembly and assembly instructions for the travel motor of an M312 excavator. It lists 44 steps to disassemble the travel motor and its components. These include removing covers, gaskets, seals, valves, springs, pins, and other parts. It then lists the assembly steps in reverse order, noting to replace all seals and gaskets, apply oil, and ensure cleanliness during assembly.
Caterpillar Cat M312 Excavator (Prefix 6TL) Service Repair Manual (6TL00001-0...paws21610697
This document provides the disassembly and assembly procedures for the swing drive of an M312 excavator. The disassembly procedure involves 28 steps to remove components such as the swing brake assembly, discs, plates, piston, seals, shaft, gears, bearings, and housing. The assembly procedure involves 17 steps and requires various tools to install components in the reverse order of disassembly while applying lubricant and ensuring proper torque specifications are achieved.
This document provides instructions for removing and installing engine oil filter bases and related components on Caterpillar 3304B and 3306B engines. The procedures describe removing the oil filter, oil filter base, gaskets and O-rings. Instructions are provided for disassembling the oil filter base by removing covers, bolts, springs and plungers. Reassembly and installation steps are also outlined. Tools required are listed for each procedure. Precautions are noted to keep parts clean and contain fluids.
Caterpillar Cat D250E II Articulated Truck (Prefix 4PS) Service Repair Manual...paws21610697
The document provides instructions for disassembling and assembling the piston pump used for steering on a D250E II Articulated Truck. The disassembly procedure involves removing 21 individual parts from the pump housing. The assembly procedure instructs assembling the 21 parts in the reverse order, applying lubrication and torque specifications as needed. Tools required include various drivers, pliers, and lubricants.
The document provides instructions for disassembling and assembling the governor of an articulated truck. It lists 57 steps to disassemble the front and rear housings of the governor. Tools required include a governor repair fixture, retaining ring pliers, pin punch, clevis driver, and legs to mount the rear housing. Cautions are provided regarding cleaning parts and containing fluids during maintenance.
The document provides instructions for disassembling and assembling a Type I governor used in Caterpillar 3114, 3116, and 3126 engines. It describes 35 steps to disassemble the governor front housing and 19 additional steps to disassemble the rear housing. Various parts are inspected for wear or damage during disassembly. Cleaning and replacement parts are also discussed. Tools required are listed.
The document provides instructions for removing and installing various engine components on a Caterpillar 3408 industrial engine, including the oil cooler, oil filter base, oil bypass valves, engine oil cooler/lines, aftercooler, and turbocharger. The procedures describe removing bolts, hoses, seals, and other parts, cleaning components, applying sealant, and reinstalling parts in reverse order.
The document provides instructions for removing and installing wheel spindles on Caterpillar articulated dump trucks. It describes removing the wheels, bearings, and seals before removing the brake shoes. It then details removing pins and springs to separate the brake shoes from the spider. Reinstallation follows the reverse order. Instructions are also given for disassembling and assembling suspension cylinders.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Caterpillar Cat W345B Series II Material Handler (Prefix CDY) Service Repair ...paws21610697
This document provides assembly instructions for a swing drive on a W345B Series II wheeled excavator. It includes a list of required tools and 40 steps to assemble the various components of the swing drive, such as bearings, seals, gears, and housings. Special attention is given to cleaning parts, applying lubricants, and torquing bolts to the specified values. The instructions also cover installing the assembled swing drive into the excavator's main frame.
1. Remove the fuel injection pump housing and governor from the engine as a single unit using lifting sling and hoist. Disconnect all connecting lines and tubes.
2. Disassemble the fuel injection pump housing by removing the retaining ring, filter base, tubes and other attached components.
3. Inspect all seals and gaskets, replacing any that are damaged, to prepare the housing for assembly.
This document provides installation instructions for removing and installing an axle shaft on the steering axle of an M325D Material Handler excavator. It is a 15 step process that includes draining fluids, removing bolts and pins, lifting out heavy components using lifting devices, replacing seals and bushings, and reinstalling components in reverse order. Special tools are required and Loctite threadlocker is used on reinstallation.
Caterpillar Cat M325D L MH EXCAVATOR (Prefix KAY) Service Repair Manual (KAY0...paws21610697
This document provides installation instructions for separating an upper frame from an undercarriage frame on an excavator. It outlines 33 steps including removing components like the stick, front and rear drive shafts, swivel, and left boom cylinder. It instructs using tools and lifting devices to reposition pins and plates to separate the frames while supporting heavy components weighing up to 500 pounds. Proper identification of hose and tube assemblies is noted for reinstallation.
Caterpillar Cat M325D L MH EXCAVATOR (Prefix KAY) Service Repair Manual (KAY0...paws21610697
This document provides instructions for disassembling and assembling the swing drive of an M325D L Material Handler excavator. It lists the required tools and presents a 31 step disassembly procedure and a 29 step assembly procedure. The procedures involve removing and installing various components of the swing drive like gears, shafts, bearings, seals and housings. Precautions are provided regarding cleanliness and safety.
The document provides instructions for disassembling the front and rear final drive carriers, hubs, and brakes of an M320 excavator. The 28 step procedure describes how to remove components like planetary carriers, sun gears, ring gears, brake pistons, bearings, and seals. Tools required include retaining ring pliers, pullers, wrenches, and hammers. Safety notices are provided to release hydraulic pressure and contain fluids before disassembly.
This document provides instructions for disassembling and assembling the rear axle carrier, hubs, and brakes of an M318F wheeled excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for removing components like the carrier housing, planetary gears, and brake discs, and installing components like the thrust washer, carrier gear, and retaining rings. The instructions aim to properly remove and replace these components while containing fluids and following safety procedures.
This document provides instructions for disassembling and assembling the rear axle carrier, hubs, and brakes of an M317F wheeled excavator. The disassembly procedure involves removing 23 components including carrier housing, planetary gears, thrust washers, retaining rings, and hub. The assembly procedure provides steps to install 23 components in reverse order and includes checking brake clearance and installing seals and bearings. Tools required include retaining ring pliers, drivers, spanners, pry bars, pullers, and torque wrenches.
The document provides instructions for removing and installing various components on a M317D2 Wheeled Excavator, including:
- Removing the swing gear and bearing by lifting it out after removing bolts and spacers.
- Installing the swing gear and bearing by positioning it with lifting tools, then installing bolts and spacers.
- Removing the hydraulic oil filter by taking off the cover, O-ring, and retainer, then removing the filter.
- Installing the hydraulic oil filter by reversing the removal steps.
- Removing the hydraulic tank by draining it, disconnecting hoses and fittings, and lifting it off after removing bolts.
- Installing the hydraulic tank by
The document provides instructions for disassembling and assembling the main hydraulic pump of a M317D2 Wheeled Excavator. It lists 34 steps for disassembly, removing components like pistons, springs, seals and bearings. It then lists 36 steps for assembly, replacing components and using various tools to set dimensions and install retaining rings, seals and bearings. Precision is required to mark positions of parts and reinstall components in their original orientation for proper function.
This document provides instructions for disassembling and assembling a swing drive on a wheeled excavator model M316D. The removal procedure involves releasing hydraulic pressure, removing hoses and bolts, and using lifting tools to remove the swing drive assembly. The disassembly procedure then describes using various tools to remove retaining rings, plates, discs, seals, gears, and other internal components. The assembly procedure outlines cleaning and lubricating parts, and using tools to reinstall components in reverse order, taking care to properly seat bearings and tighten nuts to the specified torques.
The document provides instructions for disassembling the front and rear axles of an M315F wheeled excavator. It lists required tools and presents a 23 step procedure for removing components like carrier housings, planetary gears, bearings, seals, and hubs. Detailed illustrations accompany each step to show how to properly disassemble parts. Safety notices are included to handle fluids and springs safely during the process.
The document provides disassembly and assembly instructions for the travel motor of an M312 excavator. It lists 44 steps to disassemble the travel motor and its components. These include removing covers, gaskets, seals, valves, springs, pins, and other parts. It then lists the assembly steps in reverse order, noting to replace all seals and gaskets, apply oil, and ensure cleanliness during assembly.
Caterpillar Cat M312 Excavator (Prefix 6TL) Service Repair Manual (6TL00001-0...paws21610697
This document provides the disassembly and assembly procedures for the swing drive of an M312 excavator. The disassembly procedure involves 28 steps to remove components such as the swing brake assembly, discs, plates, piston, seals, shaft, gears, bearings, and housing. The assembly procedure involves 17 steps and requires various tools to install components in the reverse order of disassembly while applying lubricant and ensuring proper torque specifications are achieved.
This document provides instructions for removing and installing engine oil filter bases and related components on Caterpillar 3304B and 3306B engines. The procedures describe removing the oil filter, oil filter base, gaskets and O-rings. Instructions are provided for disassembling the oil filter base by removing covers, bolts, springs and plungers. Reassembly and installation steps are also outlined. Tools required are listed for each procedure. Precautions are noted to keep parts clean and contain fluids.
Caterpillar Cat D250E II Articulated Truck (Prefix 4PS) Service Repair Manual...paws21610697
The document provides instructions for disassembling and assembling the piston pump used for steering on a D250E II Articulated Truck. The disassembly procedure involves removing 21 individual parts from the pump housing. The assembly procedure instructs assembling the 21 parts in the reverse order, applying lubrication and torque specifications as needed. Tools required include various drivers, pliers, and lubricants.
The document provides instructions for disassembling and assembling the governor of an articulated truck. It lists 57 steps to disassemble the front and rear housings of the governor. Tools required include a governor repair fixture, retaining ring pliers, pin punch, clevis driver, and legs to mount the rear housing. Cautions are provided regarding cleaning parts and containing fluids during maintenance.
The document provides instructions for disassembling and assembling a Type I governor used in Caterpillar 3114, 3116, and 3126 engines. It describes 35 steps to disassemble the governor front housing and 19 additional steps to disassemble the rear housing. Various parts are inspected for wear or damage during disassembly. Cleaning and replacement parts are also discussed. Tools required are listed.
The document provides instructions for removing and installing various engine components on a Caterpillar 3408 industrial engine, including the oil cooler, oil filter base, oil bypass valves, engine oil cooler/lines, aftercooler, and turbocharger. The procedures describe removing bolts, hoses, seals, and other parts, cleaning components, applying sealant, and reinstalling parts in reverse order.
The document provides instructions for removing and installing wheel spindles on Caterpillar articulated dump trucks. It describes removing the wheels, bearings, and seals before removing the brake shoes. It then details removing pins and springs to separate the brake shoes from the spider. Reinstallation follows the reverse order. Instructions are also given for disassembling and assembling suspension cylinders.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
2. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 301.8 MINI HYD EXCAVATOR H8X
Configuration: 301.8 Mini Hydraulic Excavator H8X00001-UP (MACHINE) POWERED BY C1.1 Engine
Disassembly and Assembly
301.5,301.6,301.7,301.8,302 Mini Hydraulic Excavator Machine Systems
Media Number -M0092231-00 Publication Date -01/09/2018 Date Updated -11/09/2018
i07366569
Blade Cylinder - Assemble
SMCS - 7562-016-BG
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 152-4251 Cylinder Repair Bench 1
B 1P-2853 Spanner Wrench 1
C 280-2060 Offset Spanner Wrench 1
D
8H-8539 1 5/8" Socket 1
5P-3588 Adapter 1
Illustration 1 g06295667
1/6
301.8 Mini Hydraulic Excavator H8X00001-UP (MACHINE) POWERED BY C1.1 E...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. 1. Install seal (16) and spacer (17).
Illustration 2 g06295654
2. Install O-ring seal and backup ring (14). Install O-ring seal (15).
Illustration 3 g06295640
Illustration 4 g06295645
3. Install bushing (10). Install O-ring seal (13). Install inner seal (12), and outer seal (11).
2/6
301.8 Mini Hydraulic Excavator H8X00001-UP (MACHINE) POWERED BY C1.1 E...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Illustration 5 g06296653
4. Install cylinder nut (6) onto rod end (9). Apply oil on seals and rod end for assembly.
Illustration 6 g06295422
Illustration 7 g06295757
5. Mount the rod end onto Tooling (A).
Install piston (8). Use Tooling (D) to tighten piston (8). Tighten piston (8) to a torque of
400 ± 20 N·m (295 ± 15 lb ft).
3/6
301.8 Mini Hydraulic Excavator H8X00001-UP (MACHINE) POWERED BY C1.1 E...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. Install ball and set screw (7). Tighten set screw (7) to a torque of 17 ± 2 N·m
(150 ± 18 lb in). Stake set screw in place once torque is applied.
Illustration 8 g06319794
Illustration 9 g06295798
6. Mount barrel end of cylinder (5) on Tooling (A).
Align barrel assembly (5) and the rod assembly for installation. Apply hydraulic oil inside
barrel assembly and on piston (8).
Install the piston and rod assembly inside the barrel assembly.
4/6
301.8 Mini Hydraulic Excavator H8X00001-UP (MACHINE) POWERED BY C1.1 E...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Illustration 10 g06295383
Illustration 11 g06295820
7. Install cylinder nut (6) into barrel assembly (5). Apply hydraulic oil to seals before
installation.
Use Tooling (C) to tighten cylinder nut (6) to a torque of 226 N·m (167 lb ft).
Illustration 12 g06295269
Illustration 13 g06295274
5/6
301.8 Mini Hydraulic Excavator H8X00001-UP (MACHINE) POWERED BY C1.1 E...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. 8. Install seals (1) into barrel end of blade cylinder (2). Install seals (3) into rod end of blade
cylinder (4).
End By:
a. Install blade cylinder.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Mar 8 19:44:15 UTC+0800 2020
6/6
301.8 Mini Hydraulic Excavator H8X00001-UP (MACHINE) POWERED BY C1.1 E...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 301.8 MINI HYD EXCAVATOR H8X
Configuration: 301.8 Mini Hydraulic Excavator H8X00001-UP (MACHINE) POWERED BY C1.1 Engine
Disassembly and Assembly
301.5,301.6,301.7,301.8,302 Mini Hydraulic Excavator Machine Systems
Media Number -M0092231-00 Publication Date -01/09/2018 Date Updated -11/09/2018
i07397606
Blade - Remove and Install
SMCS - 6060-010
Removal Procedure
Start By:
a. Remove blade cylinder
Illustration 1 g06310423
1. Place suitable blocking under blade assembly. Remove bolts (1) and pin assemblies (2).
1/2
301.8 Mini Hydraulic Excavator H8X00001-UP (MACHINE) POWERED BY C1.1 E...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Illustration 2 g06310444
Illustration 3 g06310445
2. Attach strap and a suitable lifting device around blade assembly (3). The weight of blade
assembly (3) is approximately 68 kg (150 lb). Remove blade assembly (3).
Installation Procedure
1. Install blade assembly (3) in the reverse order of removal.
End By:
a. Install blade cylinder
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Mar 8 19:45:12 UTC+0800 2020
2/2
301.8 Mini Hydraulic Excavator H8X00001-UP (MACHINE) POWERED BY C1.1 E...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 301.8 MINI HYD EXCAVATOR H8X
Configuration: 301.8 Mini Hydraulic Excavator H8X00001-UP (MACHINE) POWERED BY C1.1 Engine
Disassembly and Assembly
301.5,301.6,301.7,301.8,302 Mini Hydraulic Excavator Machine Systems
Media Number -M0092231-00 Publication Date -01/09/2018 Date Updated -11/09/2018
i07394729
Bucket - Remove and Install
SMCS - 6001-010; 6101-010
Removal Procedure
1. Lower bucket to the ground.
Illustration 1 g06306012
1. Remove retainer bolts (1).
1/3
301.8 Mini Hydraulic Excavator H8X00001-UP (MACHINE) POWERED BY C1.1 E...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Illustration 2 g06306014
2. Remove pins (2) from bucket linkage and stick. Remove bucket (3).
Installation Procedure
Illustration 3 g06306014
1. Position the stick over the bucket (3). Install pins (2) through the bucket linkage and the
stick.
Illustration 4 g06306012
2/3
301.8 Mini Hydraulic Excavator H8X00001-UP (MACHINE) POWERED BY C1.1 E...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. 2. Install retainer bolts (1). Place two nuts on the retainer bolts (1) to lock in place.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Mar 8 19:46:09 UTC+0800 2020
3/3
301.8 Mini Hydraulic Excavator H8X00001-UP (MACHINE) POWERED BY C1.1 E...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 301.8 MINI HYD EXCAVATOR H8X
Configuration: 301.8 Mini Hydraulic Excavator H8X00001-UP (MACHINE) POWERED BY C1.1 Engine
Disassembly and Assembly
301.5,301.6,301.7,301.8,302 Mini Hydraulic Excavator Machine Systems
Media Number -M0092231-00 Publication Date -01/09/2018 Date Updated -11/09/2018
i07390177
Bucket - Remove
SMCS - 6101-011
Removal Procedure
1. Lower bucket to the ground.
Illustration 1 g06306012
1. Remove retainer bolts (1).
1/3
301.8 Mini Hydraulic Excavator H8X00001-UP (MACHINE) POWERED BY C1.1 E...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Illustration 2 g06306014
2. Remove pins (2) from bucket linkage and stick. Remove bucket (3).
Installation Procedure
Illustration 3 g06306014
1. Position the stick over the bucket (3). Install pins (2) through the bucket linkage and the
stick.
Illustration 4 g06306012
2/3
301.8 Mini Hydraulic Excavator H8X00001-UP (MACHINE) POWERED BY C1.1 E...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. 2. Install retainer bolts (1). Place two nuts on the retainer bolts (1) to lock in place.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Mar 8 19:47:06 UTC+0800 2020
3/3
301.8 Mini Hydraulic Excavator H8X00001-UP (MACHINE) POWERED BY C1.1 E...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 301.8 MINI HYD EXCAVATOR H8X
Configuration: 301.8 Mini Hydraulic Excavator H8X00001-UP (MACHINE) POWERED BY C1.1 Engine
Disassembly and Assembly
301.5,301.6,301.7,301.8,302 Mini Hydraulic Excavator Machine Systems
Media Number -M0092231-00 Publication Date -01/09/2018 Date Updated -11/09/2018
i07394736
Bucket Linkage - Remove and Install
SMCS - 6513-010
Removal Procedure
Start By:
a. Remove Bucket
Illustration 1 g06306848
1. Remove retainer bolts (1).
1/3
301.8 Mini Hydraulic Excavator H8X00001-UP (MACHINE) POWERED BY C1.1 E...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Illustration 2 g06306893
2. Remove pin (2). Remove link assembly (3).
Illustration 3 g06306899
3. Remove pin (4) and links (5).
Installation Procedure
Illustration 4 g06306899
1. Install links (5) and pin (4) on the stick.
2/3
301.8 Mini Hydraulic Excavator H8X00001-UP (MACHINE) POWERED BY C1.1 E...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
19. Illustration 5 g06306893
2. Position link assembly (3) along with pin (2) along with the cylinder, on the stick.
Illustration 6 g06306848
3. Install retainer bolts (1). Use 2 nuts to lock retainer bolts (1) in place.
End By:
a. Install Bucket
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Mar 8 19:48:02 UTC+0800 2020
3/3
301.8 Mini Hydraulic Excavator H8X00001-UP (MACHINE) POWERED BY C1.1 E...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 301.8 MINI HYD EXCAVATOR H8X
Configuration: 301.8 Mini Hydraulic Excavator H8X00001-UP (MACHINE) POWERED BY C1.1 Engine
Disassembly and Assembly
301.5,301.6,301.7,301.8,302 Mini Hydraulic Excavator Machine Systems
Media Number -M0092231-00 Publication Date -01/09/2018 Date Updated -11/09/2018
i07394846
Bucket Cylinder - Remove and Install
SMCS - 5457-010-G1
Removal Procedure
Start By:
a. Disconnect Bucket Linkage
b. Relieve System Pressure
Cylinders equipped with lock valves can remain pressurized for very
long periods of time, even with the hoses removed.
Failure to relieve pressure before removing a lock valve or
disassembling a cylinder can result in personal injury or death.
Ensure all pressure is relieved before removing a lock valve or
disassembling a cylinder.
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
1/3
301.8 Mini Hydraulic Excavator H8X00001-UP (MACHINE) POWERED BY C1.1 E...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
Illustration 1 g06306937
Illustration 2 g06306978
1. Disconnect hose assemblies (1) from bucket cylinder (2). Remove clamps (3).
2/3
301.8 Mini Hydraulic Excavator H8X00001-UP (MACHINE) POWERED BY C1.1 E...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Illustration 3 g06306982
2. Remove bolt (4), pin assembly (5), and bucket cylinder (2).
Installation Procedure
Illustration 4 g06306982
1. Position bucket cylinder (2) in place on the stick. Install pin assembly (5) and bolt (4).
Illustration 5 g06306937
2. Attach hose assemblies (2) to bucket cylinder (2).
End By:
a. Connect the bucket linkage assembly.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Mar 8 19:48:59 UTC+0800 2020
3/3
301.8 Mini Hydraulic Excavator H8X00001-UP (MACHINE) POWERED BY C1.1 E...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...