The document provides instructions for removing and installing a fuel injection pump and governor from a Caterpillar 277D Multi Terrain Loader. It describes 17 steps to disassemble the components, including using specific tools to remove gears, bearings, springs, levers and other parts. Similarly, it lists 18 steps for reassembling and installing the pump and governor, noting torque specifications for certain bolts and nuts. Safety cautions are also provided throughout the procedures.
Caterpillar cat 277 d multi terrain loader (prefix mlt) service repair manual...ufjjskekkmde
This document provides instructions for disassembling and assembling the fuel injection pump and governor for a 277D Multi Terrain Loader with a C3.3B engine. The disassembly procedure involves removing 17 parts including the governor housing assembly, shaft, springs, and bearings. The assembly procedure instructs installing these 17 parts in reverse order and provides torque specifications for nuts and bolts. Tools including an injection pump gear puller and bearing puller are required. Cleanliness of fuel system components is emphasized.
Caterpillar cat 277 d multi terrain loader (prefix mlt) service repair manual...jjskefkskemik
This document provides instructions for disassembling and assembling the fuel injection pump and governor for a 277D Multi Terrain Loader with a C3.3B engine. The disassembly procedure involves removing 17 parts including the governor housing assembly, shaft, springs, and bearings. The assembly procedure instructs installing these 17 parts in reverse order and provides torque specifications for nuts and bolts. Tools including an injection pump gear puller and bearing puller are required.
Caterpillar cat 277 d multi terrain loader (prefix mlt) service repair manual...fujsjfkkskefsme
This document provides instructions for disassembling and assembling the fuel injection pump and governor for a 277D Multi Terrain Loader with a C3.3B engine. The disassembly procedure involves removing 17 parts including the governor housing assembly, shaft, springs, and bearings. The assembly procedure instructs installing these 17 parts in reverse order and provides torque specifications for nuts and bolts. Tools including an injection pump gear puller and bearing puller are required.
Caterpillar cat 277 d multi terrain loader (prefix mlt) service repair manual...ufjjdkskemmd
This document provides instructions for disassembling and assembling the fuel injection pump and governor for a 277D Multi Terrain Loader with a C3.3B engine. The disassembly procedure involves removing 17 parts including the governor housing assembly, shaft, springs, and bearings. The assembly procedure instructs installing these 17 parts in reverse order and provides torque specifications for nuts and bolts. Tools including an injection pump gear puller and bearing puller are required.
Caterpillar cat 287 d multi terrain loader (prefix tlk) service repair manual...fhshefjjskefkem
The document provides instructions for disassembling and assembling the fuel injection pump and governor for a 287D Multi Terrain Loader with a C3.3B engine. It describes removing 17 parts including the governor housing, fuel camshaft, bearings and gears. It then describes assembling the components in the reverse order, noting to apply oil and torque bolts and nuts to the specified values. The document also includes instructions for installing the fuel injection pump and governor on the engine, attaching lines and covers.
Caterpillar cat 287 d multi terrain loader (prefix tlk) service repair manual...ufjjjskkmsmed
The document provides instructions for disassembling and assembling the fuel injection pump and governor for a 287D Multi Terrain Loader with a C3.3B engine. It describes removing 17 parts including the governor housing, fuel camshaft, bearings and gears. It then describes assembling the parts in the reverse order, noting to apply oil and torque bolts and nuts to the specified values. A separate section provides instructions for installing the fuel injection pump and governor on the engine, attaching lines and covers.
Caterpillar cat 287 d multi terrain loader (prefix tlk) service repair manual...fjjskekskem
The document provides instructions for disassembling and assembling the fuel injection pump and governor of a Caterpillar C3.3B engine. It describes 17 steps for disassembly, including using tools to remove gears, shafts, springs, levers and other components. It then describes 18 steps for assembly, providing details on installing components in the reverse order and specifying torque values for fasteners. The overall procedure involves precisely disassembling and reassembling the intricate parts of the fuel injection pump and governor system.
Caterpillar cat 287 d multi terrain loader (prefix tlk) service repair manual...ujfjdkkmsme
The document provides instructions for disassembling and assembling the fuel injection pump and governor for a 287D Multi Terrain Loader with a C3.3B engine. It describes 17 steps for disassembly, including removing bolts, shafts, springs, seals and other components. It then describes 18 steps for assembly, including installing bearings, seals, springs and other components and tightening to the specified torques. The fuel injection pump and governor installation procedure is also provided, with 7 steps including installing seals, nuts and sensors.
Caterpillar cat 277 d multi terrain loader (prefix mlt) service repair manual...ufjjskekkmde
This document provides instructions for disassembling and assembling the fuel injection pump and governor for a 277D Multi Terrain Loader with a C3.3B engine. The disassembly procedure involves removing 17 parts including the governor housing assembly, shaft, springs, and bearings. The assembly procedure instructs installing these 17 parts in reverse order and provides torque specifications for nuts and bolts. Tools including an injection pump gear puller and bearing puller are required. Cleanliness of fuel system components is emphasized.
Caterpillar cat 277 d multi terrain loader (prefix mlt) service repair manual...jjskefkskemik
This document provides instructions for disassembling and assembling the fuel injection pump and governor for a 277D Multi Terrain Loader with a C3.3B engine. The disassembly procedure involves removing 17 parts including the governor housing assembly, shaft, springs, and bearings. The assembly procedure instructs installing these 17 parts in reverse order and provides torque specifications for nuts and bolts. Tools including an injection pump gear puller and bearing puller are required.
Caterpillar cat 277 d multi terrain loader (prefix mlt) service repair manual...fujsjfkkskefsme
This document provides instructions for disassembling and assembling the fuel injection pump and governor for a 277D Multi Terrain Loader with a C3.3B engine. The disassembly procedure involves removing 17 parts including the governor housing assembly, shaft, springs, and bearings. The assembly procedure instructs installing these 17 parts in reverse order and provides torque specifications for nuts and bolts. Tools including an injection pump gear puller and bearing puller are required.
Caterpillar cat 277 d multi terrain loader (prefix mlt) service repair manual...ufjjdkskemmd
This document provides instructions for disassembling and assembling the fuel injection pump and governor for a 277D Multi Terrain Loader with a C3.3B engine. The disassembly procedure involves removing 17 parts including the governor housing assembly, shaft, springs, and bearings. The assembly procedure instructs installing these 17 parts in reverse order and provides torque specifications for nuts and bolts. Tools including an injection pump gear puller and bearing puller are required.
Caterpillar cat 287 d multi terrain loader (prefix tlk) service repair manual...fhshefjjskefkem
The document provides instructions for disassembling and assembling the fuel injection pump and governor for a 287D Multi Terrain Loader with a C3.3B engine. It describes removing 17 parts including the governor housing, fuel camshaft, bearings and gears. It then describes assembling the components in the reverse order, noting to apply oil and torque bolts and nuts to the specified values. The document also includes instructions for installing the fuel injection pump and governor on the engine, attaching lines and covers.
Caterpillar cat 287 d multi terrain loader (prefix tlk) service repair manual...ufjjjskkmsmed
The document provides instructions for disassembling and assembling the fuel injection pump and governor for a 287D Multi Terrain Loader with a C3.3B engine. It describes removing 17 parts including the governor housing, fuel camshaft, bearings and gears. It then describes assembling the parts in the reverse order, noting to apply oil and torque bolts and nuts to the specified values. A separate section provides instructions for installing the fuel injection pump and governor on the engine, attaching lines and covers.
Caterpillar cat 287 d multi terrain loader (prefix tlk) service repair manual...fjjskekskem
The document provides instructions for disassembling and assembling the fuel injection pump and governor of a Caterpillar C3.3B engine. It describes 17 steps for disassembly, including using tools to remove gears, shafts, springs, levers and other components. It then describes 18 steps for assembly, providing details on installing components in the reverse order and specifying torque values for fasteners. The overall procedure involves precisely disassembling and reassembling the intricate parts of the fuel injection pump and governor system.
Caterpillar cat 287 d multi terrain loader (prefix tlk) service repair manual...ujfjdkkmsme
The document provides instructions for disassembling and assembling the fuel injection pump and governor for a 287D Multi Terrain Loader with a C3.3B engine. It describes 17 steps for disassembly, including removing bolts, shafts, springs, seals and other components. It then describes 18 steps for assembly, including installing bearings, seals, springs and other components and tightening to the specified torques. The fuel injection pump and governor installation procedure is also provided, with 7 steps including installing seals, nuts and sensors.
Caterpillar cat 287 d multi terrain loader (prefix tlk) service repair manual...fujsjefskekfksem
The document provides instructions for disassembling and assembling the fuel injection pump and governor for a 287D Multi Terrain Loader with a C3.3B engine. It describes removing 17 parts including the governor housing, fuel camshaft, bearings and gears. It then describes assembling the components in the reverse order, noting to apply oil and torque bolts and nuts to the specified values. The document also includes instructions for installing the fuel injection pump and governor on the engine, attaching lines and covers.
Caterpillar Cat 287D MULTI TERRAIN LOADER (Prefix TLK) Service Repair Manual ...tengtui535
The document provides instructions for disassembling and assembling the fuel injection pump and governor for a 287D Multi Terrain Loader with a C3.3B engine. It describes removing 17 parts including the governor housing assembly, shaft, springs, and bearings. It then describes assembling the parts in reverse order, noting torque specifications for nuts and bolts. The goal is to remove the fuel injection pump and governor from the engine.
Caterpillar Cat 287D MULTI TERRAIN LOADER (Prefix TLK) Service Repair Manual ...f8seodkdmdmed3
The document provides instructions for disassembling and assembling the fuel injection pump and governor for a 287D Multi Terrain Loader with a C3.3B engine. It describes removing 17 parts including the governor housing assembly, shaft, springs, and bearings. It then describes assembling the components in reverse order, noting specific torque specifications for nuts and bolts. The purpose is to repair or replace parts in the fuel injection pump and governor assembly.
Caterpillar Cat 287D MULTI TERRAIN LOADER (Prefix TLK) Service Repair Manual ...f8usejkdmmd8i
The document provides instructions for disassembling and assembling the fuel injection pump and governor of a Caterpillar C3.3B engine. It describes 17 steps for disassembly, including removing bolts, shafts, springs, and bearings. It then describes 18 steps for assembly, including pressing bearings onto shafts, installing springs, weights, and housings, and tightening components to specified torques. A separate section details installing the fuel injection pump and governor onto the engine, attaching brackets and fittings.
Caterpillar Cat 287D MULTI TERRAIN LOADER (Prefix TLK) Service Repair Manual ...gongfuao7509
The document provides instructions for disassembling and assembling the fuel injection pump and governor for a Caterpillar 287D Multi Terrain Loader. It describes 17 steps for disassembly, including removing the governor housing assembly, shaft, spring, and other internal parts. It then describes 18 steps for assembly, including installing bearings on the fuel camshaft, positioning internal parts, and installing the governor housing assembly. Finally, it provides instructions for installing the fuel injection pump and governor on the engine, including attaching nuts and connecting wiring.
Caterpillar Cat 287D MULTI TERRAIN LOADER (Prefix TLK) Service Repair Manual ...ze6074xunong
The document provides instructions for disassembling and assembling the fuel injection pump and governor of a Caterpillar C3.3B engine. It describes 17 steps for disassembly, including removing bolts, shafts, springs, and bearings. It then describes 18 steps for assembly, including pressing bearings onto shafts, installing springs, weights, and plates, and tightening bolts and nuts to specified torques. Finally, it lists the procedure for installing the fuel injection pump and governor onto the engine, including applying oil and tightening nuts.
Caterpillar Cat 287D MULTI TERRAIN LOADER (Prefix TLK) Service Repair Manual ...jfkksemmdmd
The document provides instructions for disassembling and assembling the fuel injection pump and governor for a Caterpillar 287D Multi Terrain Loader. The disassembly procedure involves removing 17 parts from the fuel injection pump and governor assembly including the governor housing, stop solenoid, governor lever, speed control lever, governor sleeve, governor weights, gear, retaining plates, fuel camshaft, bearings and more. Corresponding assembly instructions are also provided to reinstall the removed components in reverse order.
This document provides instructions for removing and installing a fuel injection pump on a 246D Skid Steer Loader powered by a C3.3B engine. The procedure involves disconnecting fuel lines, removing mounting nuts and bolts, and extracting the pump. When installing, new gasket shims are used and bolts are tightened to the specified torques. Cleanliness of all fuel system components is emphasized to prevent contamination.
This document provides instructions for removing and installing a fuel injection pump on a 246D Skid Steer Loader powered by a C3.3B engine. The procedure involves disconnecting fuel lines, removing mounting nuts and bolts, and extracting the pump. When installing, new gasket shims are used and bolts are tightened to the specified torques. Cleanliness of all fuel system components is emphasized to prevent contamination.
The document provides instructions for disassembling and assembling the fuel injection pump and governor of a 246D Skid Steer Loader. It describes 17 steps to disassemble the components, including using specific tools to remove gears, bearings, springs and other parts. It then describes 18 steps for reassembling the components in reverse order, noting specific torque specifications. The final section describes 7 steps for removing and reinstalling the entire fuel injection pump.
The document provides instructions for disassembling and assembling the fuel injection pump and governor of a 246D Skid Steer Loader. It describes 17 steps to disassemble the components, including using specific tools to remove gears, bearings, springs and other parts. It then describes 18 steps for reassembling the components in reverse order, noting specific torque specifications. The final section describes 7 steps for removing and reinstalling the entire fuel injection pump.
This document provides instructions for removing and installing a fuel injection pump on a 246D Skid Steer Loader powered by a C3.3B engine. The procedure involves disconnecting fuel lines, removing mounting nuts and bolts, and extracting the pump. When installing, new gasket shims are used and bolts are tightened to the specified torques. Cleanliness of all fuel system components is emphasized to prevent contamination.
This document provides instructions for removing and installing a fuel injection pump on a 246D Skid Steer Loader powered by a C3.3B engine. The procedure involves disconnecting fuel lines, removing mounting nuts and bolts, and carefully withdrawing the pump. New gasket shims and bolts are installed when reinstalling the pump. Cleanliness of all fuel system components is emphasized.
The document provides instructions for disassembling and assembling the fuel injection pump and governor of a 246D Skid Steer Loader. It describes 17 steps to disassemble the components, including using specific tools to remove gears, shafts, springs, and bearings. It then describes 18 steps for reassembling the components in reverse order, noting specific torque specifications. The purpose is to repair or replace parts of the fuel injection pump and governor system.
This document provides instructions for removing and installing a fuel injection pump on a 246D Skid Steer Loader powered by a C3.3B engine. The procedure involves disconnecting fuel lines, removing mounting nuts and bolts, and extracting the pump. When installing, new gasket shims must be used and cleanliness of all components is critical. Bolts and nuts are tightened to specified torques once the pump is positioned in the housing.
The document provides instructions for disassembling and assembling the fuel injection pump and governor of a 246D Skid Steer Loader. It describes 17 steps to disassemble the components, including using various tools to remove gears, shafts, springs, and bearings. It then describes 18 steps for reassembling the components in reverse order, noting specific torque specifications. The purpose is to repair or replace parts of the fuel injection pump and governor system.
The document provides instructions for removing and installing various powertrain components on a 745C articulated truck, including:
1) Removing and installing the torque converter, which requires using lifting tools and weighs approximately 95 kg.
2) Removing and installing the transmission scavenge pump, which involves disconnecting hoses and removing mounting bolts.
3) Removing and installing the transmission oil filter, which requires releasing system pressure and removing mounting bolts and harnesses.
This document provides instructions for removing and installing the front suspension frame on a 745 Articulated Truck. The removal procedure involves disconnecting hydraulic lines, removing mounting bolts, and using lifting equipment to remove the heavy frame component. The installation procedure is the reverse of removal, and includes priming bearings with grease, tightening bolts to the specified torque values, and reconnecting hydraulic lines. Safety precautions are provided regarding working under heavy components and relieving hydraulic pressure.
This document provides instructions for removing and installing various diesel exhaust fluid (DEF) system components on a Caterpillar 730C Ejector Articulated Truck. It includes procedures for the DEF tank, pump, injector, electronic control module, heater coolant solenoid valve, and fuel solenoid valve. The document contains illustrations and torque specifications for each component. Safety and installation notes are also provided.
This document provides instructions for removing and disassembling the engine and torque converter from a Caterpillar 730C Ejector Articulated Truck. It describes disconnecting wiring harnesses, hoses, brackets, and removing bolts to detach the engine. It then outlines steps to disassemble the torque converter including removing housing, bearings, plates, and seals. The instructions are detailed with illustrations and cautions for safe removal of pressurized components.
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly due to its weight.
This document provides instructions for servicing the grapple arch cylinder on a 527 Track Skidder. It describes how to remove the cylinder by disconnecting hoses, removing retaining pins, and lifting it from the arch. It then details how to disassemble the cylinder by removing seals and bearings. The assembly process is outlined as well, including installing new seals and bearings and reattaching the cylinder to the arch using retaining pins.
More Related Content
Similar to Caterpillar Cat 277D MULTI TERRAIN LOADER (Prefix MLT) Service Repair Manual (MLT00001 and up).pdf
Caterpillar cat 287 d multi terrain loader (prefix tlk) service repair manual...fujsjefskekfksem
The document provides instructions for disassembling and assembling the fuel injection pump and governor for a 287D Multi Terrain Loader with a C3.3B engine. It describes removing 17 parts including the governor housing, fuel camshaft, bearings and gears. It then describes assembling the components in the reverse order, noting to apply oil and torque bolts and nuts to the specified values. The document also includes instructions for installing the fuel injection pump and governor on the engine, attaching lines and covers.
Caterpillar Cat 287D MULTI TERRAIN LOADER (Prefix TLK) Service Repair Manual ...tengtui535
The document provides instructions for disassembling and assembling the fuel injection pump and governor for a 287D Multi Terrain Loader with a C3.3B engine. It describes removing 17 parts including the governor housing assembly, shaft, springs, and bearings. It then describes assembling the parts in reverse order, noting torque specifications for nuts and bolts. The goal is to remove the fuel injection pump and governor from the engine.
Caterpillar Cat 287D MULTI TERRAIN LOADER (Prefix TLK) Service Repair Manual ...f8seodkdmdmed3
The document provides instructions for disassembling and assembling the fuel injection pump and governor for a 287D Multi Terrain Loader with a C3.3B engine. It describes removing 17 parts including the governor housing assembly, shaft, springs, and bearings. It then describes assembling the components in reverse order, noting specific torque specifications for nuts and bolts. The purpose is to repair or replace parts in the fuel injection pump and governor assembly.
Caterpillar Cat 287D MULTI TERRAIN LOADER (Prefix TLK) Service Repair Manual ...f8usejkdmmd8i
The document provides instructions for disassembling and assembling the fuel injection pump and governor of a Caterpillar C3.3B engine. It describes 17 steps for disassembly, including removing bolts, shafts, springs, and bearings. It then describes 18 steps for assembly, including pressing bearings onto shafts, installing springs, weights, and housings, and tightening components to specified torques. A separate section details installing the fuel injection pump and governor onto the engine, attaching brackets and fittings.
Caterpillar Cat 287D MULTI TERRAIN LOADER (Prefix TLK) Service Repair Manual ...gongfuao7509
The document provides instructions for disassembling and assembling the fuel injection pump and governor for a Caterpillar 287D Multi Terrain Loader. It describes 17 steps for disassembly, including removing the governor housing assembly, shaft, spring, and other internal parts. It then describes 18 steps for assembly, including installing bearings on the fuel camshaft, positioning internal parts, and installing the governor housing assembly. Finally, it provides instructions for installing the fuel injection pump and governor on the engine, including attaching nuts and connecting wiring.
Caterpillar Cat 287D MULTI TERRAIN LOADER (Prefix TLK) Service Repair Manual ...ze6074xunong
The document provides instructions for disassembling and assembling the fuel injection pump and governor of a Caterpillar C3.3B engine. It describes 17 steps for disassembly, including removing bolts, shafts, springs, and bearings. It then describes 18 steps for assembly, including pressing bearings onto shafts, installing springs, weights, and plates, and tightening bolts and nuts to specified torques. Finally, it lists the procedure for installing the fuel injection pump and governor onto the engine, including applying oil and tightening nuts.
Caterpillar Cat 287D MULTI TERRAIN LOADER (Prefix TLK) Service Repair Manual ...jfkksemmdmd
The document provides instructions for disassembling and assembling the fuel injection pump and governor for a Caterpillar 287D Multi Terrain Loader. The disassembly procedure involves removing 17 parts from the fuel injection pump and governor assembly including the governor housing, stop solenoid, governor lever, speed control lever, governor sleeve, governor weights, gear, retaining plates, fuel camshaft, bearings and more. Corresponding assembly instructions are also provided to reinstall the removed components in reverse order.
This document provides instructions for removing and installing a fuel injection pump on a 246D Skid Steer Loader powered by a C3.3B engine. The procedure involves disconnecting fuel lines, removing mounting nuts and bolts, and extracting the pump. When installing, new gasket shims are used and bolts are tightened to the specified torques. Cleanliness of all fuel system components is emphasized to prevent contamination.
This document provides instructions for removing and installing a fuel injection pump on a 246D Skid Steer Loader powered by a C3.3B engine. The procedure involves disconnecting fuel lines, removing mounting nuts and bolts, and extracting the pump. When installing, new gasket shims are used and bolts are tightened to the specified torques. Cleanliness of all fuel system components is emphasized to prevent contamination.
The document provides instructions for disassembling and assembling the fuel injection pump and governor of a 246D Skid Steer Loader. It describes 17 steps to disassemble the components, including using specific tools to remove gears, bearings, springs and other parts. It then describes 18 steps for reassembling the components in reverse order, noting specific torque specifications. The final section describes 7 steps for removing and reinstalling the entire fuel injection pump.
The document provides instructions for disassembling and assembling the fuel injection pump and governor of a 246D Skid Steer Loader. It describes 17 steps to disassemble the components, including using specific tools to remove gears, bearings, springs and other parts. It then describes 18 steps for reassembling the components in reverse order, noting specific torque specifications. The final section describes 7 steps for removing and reinstalling the entire fuel injection pump.
This document provides instructions for removing and installing a fuel injection pump on a 246D Skid Steer Loader powered by a C3.3B engine. The procedure involves disconnecting fuel lines, removing mounting nuts and bolts, and extracting the pump. When installing, new gasket shims are used and bolts are tightened to the specified torques. Cleanliness of all fuel system components is emphasized to prevent contamination.
This document provides instructions for removing and installing a fuel injection pump on a 246D Skid Steer Loader powered by a C3.3B engine. The procedure involves disconnecting fuel lines, removing mounting nuts and bolts, and carefully withdrawing the pump. New gasket shims and bolts are installed when reinstalling the pump. Cleanliness of all fuel system components is emphasized.
The document provides instructions for disassembling and assembling the fuel injection pump and governor of a 246D Skid Steer Loader. It describes 17 steps to disassemble the components, including using specific tools to remove gears, shafts, springs, and bearings. It then describes 18 steps for reassembling the components in reverse order, noting specific torque specifications. The purpose is to repair or replace parts of the fuel injection pump and governor system.
This document provides instructions for removing and installing a fuel injection pump on a 246D Skid Steer Loader powered by a C3.3B engine. The procedure involves disconnecting fuel lines, removing mounting nuts and bolts, and extracting the pump. When installing, new gasket shims must be used and cleanliness of all components is critical. Bolts and nuts are tightened to specified torques once the pump is positioned in the housing.
The document provides instructions for disassembling and assembling the fuel injection pump and governor of a 246D Skid Steer Loader. It describes 17 steps to disassemble the components, including using various tools to remove gears, shafts, springs, and bearings. It then describes 18 steps for reassembling the components in reverse order, noting specific torque specifications. The purpose is to repair or replace parts of the fuel injection pump and governor system.
Similar to Caterpillar Cat 277D MULTI TERRAIN LOADER (Prefix MLT) Service Repair Manual (MLT00001 and up).pdf (16)
The document provides instructions for removing and installing various powertrain components on a 745C articulated truck, including:
1) Removing and installing the torque converter, which requires using lifting tools and weighs approximately 95 kg.
2) Removing and installing the transmission scavenge pump, which involves disconnecting hoses and removing mounting bolts.
3) Removing and installing the transmission oil filter, which requires releasing system pressure and removing mounting bolts and harnesses.
This document provides instructions for removing and installing the front suspension frame on a 745 Articulated Truck. The removal procedure involves disconnecting hydraulic lines, removing mounting bolts, and using lifting equipment to remove the heavy frame component. The installation procedure is the reverse of removal, and includes priming bearings with grease, tightening bolts to the specified torque values, and reconnecting hydraulic lines. Safety precautions are provided regarding working under heavy components and relieving hydraulic pressure.
This document provides instructions for removing and installing various diesel exhaust fluid (DEF) system components on a Caterpillar 730C Ejector Articulated Truck. It includes procedures for the DEF tank, pump, injector, electronic control module, heater coolant solenoid valve, and fuel solenoid valve. The document contains illustrations and torque specifications for each component. Safety and installation notes are also provided.
This document provides instructions for removing and disassembling the engine and torque converter from a Caterpillar 730C Ejector Articulated Truck. It describes disconnecting wiring harnesses, hoses, brackets, and removing bolts to detach the engine. It then outlines steps to disassemble the torque converter including removing housing, bearings, plates, and seals. The instructions are detailed with illustrations and cautions for safe removal of pressurized components.
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly due to its weight.
This document provides instructions for servicing the grapple arch cylinder on a 527 Track Skidder. It describes how to remove the cylinder by disconnecting hoses, removing retaining pins, and lifting it from the arch. It then details how to disassemble the cylinder by removing seals and bearings. The assembly process is outlined as well, including installing new seals and bearings and reattaching the cylinder to the arch using retaining pins.
This document provides instructions for removing the transmission from a 432F2 backhoe loader. It describes:
1) Placing jack stands under the front and rear of the loader to lift it 1270 mm off the ground for access.
2) Draining the transmission oil per the operation manual before removal.
3) Removing mounting bolts, brackets, and other hardware to separate the transmission from the loader.
This document provides instructions for removing and installing the flywheel housing and crankshaft front seal on a 3054 engine. It outlines the required tools and safety precautions, and gives a step-by-step process including supporting the engine, removing mounting bolts, lifting the housing off with links, cleaning surfaces, and torquing bolts to specified values. It also describes removing the crankshaft front seal by drilling holes and pulling it out, and installing the new seal by lubricating the lip and pressing it into place.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and safety precautions. The removal procedure involves first removing the electric starting motor and flywheel. For engines with a 14-bolt housing, the housing is then removed by taking out bolts and removing the housing and gasket from dowels in the cylinder block. For engines with a 10-bolt housing, the one-piece housing assembly is removed after loosening bolts in sequence. The installation procedure provides instructions for cleaning parts, placing the housing and seal over a tool, and tightening bolts to the specified torque.
This document provides instructions for removing and installing fuel injection nozzles and inlet and exhaust valve springs on a Caterpillar 3054 engine. The fuel injection nozzle removal procedure involves removing fuel lines, loosening a threaded nut, and removing the nozzle and seat washer. Installation requires cleaning threads, installing a new seat washer, applying anti-seize compound, and tightening the nut. The valve spring procedure requires using a compressor tool to compress springs, removing keepers and retainers, and replacing springs in the reverse order. Tools and torque specifications are provided.
This document provides instructions for removing and installing fuel injection nozzles and fuel injection pumps on a Caterpillar 3054 engine. It describes the required tools and safety precautions. The procedures include removing fuel lines, loosening nuts, removing nozzles and pumps, and installing new seals and washers. Precise positioning and torque specifications are noted to maintain proper timing.
The document provides instructions for removing and installing a hydraulic tank on a 420F backhoe loader. The removal procedure involves:
1. Disconnecting hoses from the hydraulic tank assembly
2. Disconnecting clamps on hoses connected to the tank
3. Removing bolts to detach the tank from the vehicle
4. Removing additional components like a strainer and gauge from the tank. The installation procedure is the reverse of removal.
The document provides instructions for removing and installing a tie rod on the front steering of a 420D backhoe loader. It lists the required tool as a transmission repair stand and instructs the user to first remove the front axle from the machine. Safety precautions are provided to release hydraulic pressure before servicing. Detailed steps are then outlined to remove the tie rod from the axle and install a new one.
This document provides instructions for disassembling and assembling components of a 320C excavator travel motor. The summary is:
1. The travel motor disassembly procedure involves removing bolts, seals, springs, plates, and pistons from the motor housing.
2. Cleaning and applying identification marks to components is important to prevent contamination and ensure correct reassembly.
3. Tools are required to remove some components, including link brackets, slide hammers, bearing pullers, and crossblocks.
This document provides instructions for removing and disassembling the water pump on a Caterpillar 320C excavator engine. The key steps include:
1. Draining the coolant and removing the V-belts.
2. Removing four bolts to separate the water pump, pulley, and O-ring from the engine.
3. Heating the water pump to 80°C to make disassembly easier, then removing four bolts and the pulley from the pump housing.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
Caterpillar Cat 320C L Excavator (Prefix JTG) Service Repair Manual (JTG00001...f8usjejkdmmd
The documents provide instructions for servicing the travel motor of a 320C excavator, including removing and installing the counterbalance valve, removing and disassembling the travel motor, and assembling the travel motor. The documents describe each step in detail and include illustrations to identify the relevant components. Proper cleaning, containment of fluids, and replacement of O-rings are emphasized throughout.
Caterpillar Cat 320C L Excavator (Prefix MAB) Service Repair Manual (MAB00001...f8usjejkdmmd
This document provides instructions for disassembling a recoil spring assembly. It begins by removing the front idler and recoil spring assembly from the machine. A specialized recoil spring bench tool is then used to disassemble the recoil spring. The spring is under high tension and special precautions are required when handling it. The tool supports the spring and allows the retaining nut to be safely removed with a hydraulic cylinder, releasing the compressed spring.
The documents provide instructions for servicing components of a 320C excavator, including installing a counterbalance valve, removing and disassembling the travel motor, and assembling the travel motor. The documents describe cleaning parts and containing fluids, detail the required tools, and outline the step-by-step processes for installing, removing, and disassembling/assembling various components while taking appropriate safety precautions.
Caterpillar Cat 320C L Excavator (Prefix DBG) Service Repair Manual (DBG00001...f8usjejkdmmd
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
2. Shutdown SIS
Previous Screen
Product: MULTI TERRAIN LOADER
Model: 277D MULTI TERRAIN LOADER MLT
Configuration: 277D Multi Terrain Loader MLT00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
C2.6 and C3.3B Engines for Caterpillar Built Machines
Media Number -UENR0137-11 Publication Date -01/08/2015 Date Updated -12/07/2018
i05242439
Fuel Injection Pump and Governor - Disassemble
SMCS - 1286-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
390-1150 Injection Pump Gear Puller 1
154-6360 Bolt 1
B 8H-0663 Bearing Puller 1
Start By:
a. Remove fuel injection pump and governor.
Illustration 1 g02805638
1/6
277D Multi Terrain Loader MLT00001-UP (MACHINE) POWERED BY C3.3B Engi...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. 1. Inspect fuel injection pump and governor (1).
2. Remove tube (2).
Illustration 2 g02805639
3. Use suitable blocking and position the fuel injection pump and governor. Remove bolts (4)
and remove governor housing assembly (3).
4. Remove two bolts (4B) and remove stop solenoid (4A). Replace o-ring if necessary.
Illustration 3 g02805640
5. Remove and inspect O-ring seal (5) from governor housing assembly (3). If necessary,
replace O-ring seal (5) with new.
6. Remove shaft (6) and spring (7) from governor housing assembly (3). Remove governor
lever (8).
2/6
277D Multi Terrain Loader MLT00001-UP (MACHINE) POWERED BY C3.3B Engi...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 4 g02805641
7. Remove pin (10) from governor lever assembly (12).
8. Remove speed control lever (9) and spring (11) from governor lever assembly (12).
9. Remove spring (13) and remove governor lever assembly (12) with the O-ring seals.
Illustration 5 g02805656
Illustration 6 g02805658
10. Remove governor sleeve (13) and nut (16). Remove governor weights (15).
3/6
277D Multi Terrain Loader MLT00001-UP (MACHINE) POWERED BY C3.3B Engi...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 7 g02805660
Illustration 8 g02805696
11. Remove nut (17) from gear (18).
Note: Nut (17) has reverse threads.
12. Use Tooling (A) to remove gear (18).
Illustration 9 g02805716
13. Remove bolts (19) and retaining plate (20).
14. Remove fuel camshaft (24) from the housing assembly.
4/6
277D Multi Terrain Loader MLT00001-UP (MACHINE) POWERED BY C3.3B Engi...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 15. Remove screws (21) and retaining plate (22). If necessary, replace key (23) with new.
Illustration 10 g02805762
Illustration 11 g02805764
Illustration 12 g02805765
16. Use a suitable press and Tooling (B) to remove bearing (25) from fuel camshaft (24) and
ring (27).
17. Use a suitable press and Tooling (B) to remove bearing (26) from fuel camshaft (24).
5/6
277D Multi Terrain Loader MLT00001-UP (MACHINE) POWERED BY C3.3B Engi...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Shutdown SIS
Previous Screen
Product: MULTI TERRAIN LOADER
Model: 277D MULTI TERRAIN LOADER MLT
Configuration: 277D Multi Terrain Loader MLT00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
C2.6 and C3.3B Engines for Caterpillar Built Machines
Media Number -UENR0137-11 Publication Date -01/08/2015 Date Updated -12/07/2018
i05242445
Fuel Injection Pump and Governor - Assemble
SMCS - 1286-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
390-1150 Injection Pump Gear Puller 1
154-6360 Bolt 1
B 8H-0663 Bearing Puller 1
Note: Refer to Specification UENR0995 "Engine Design" for non-specified engine Torque
Values.
Illustration 1 g02805765
1/6
277D Multi Terrain Loader MLT00001-UP (MACHINE) POWERED BY C3.3B Engi...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 2 g02807019
Illustration 3 g02807020
1. Use Tooling (B) and a suitable press to install bearings (26) onto fuel camshaft (24).
2. Position ring (27). Use Tooling (B) and a suitable press to install bearings (25) onto fuel
camshaft (24).
Illustration 4 g02805716
3. If necessary, replace key (23) with new. Position retaining plate (22) and install screws (21).
Tighten screws (21) to a torque of 3.9 to 4.2 N·m (34.5 to 37.4 lb in).
2/6
277D Multi Terrain Loader MLT00001-UP (MACHINE) POWERED BY C3.3B Engi...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 4. Position fuel camshaft (24) in the housing assembly.
5. Position retaining plate (20) and install bolts (19). Tighten bolts (19) to a torque of
10 to 11 N·m (87 to 100 lb in).
Illustration 5 g02805660
6. Install gear (18).
7. Install nut (17) to gear (18).
8. For the C3.3B Tighten nut (17) to a torque of 138 to 156 N·m (102 to 115 lb ft).
9. For the C2.6 Tighten nut (17) to a torque of 93 to 102 N·m (69 to 75 lb ft).
Illustration 6 g02805658
3/6
277D Multi Terrain Loader MLT00001-UP (MACHINE) POWERED BY C3.3B Engi...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 7 g02805656
10. Position governor weights (15) and install nut (16). Tighten nut (16) to a torque of
63 to 72 N·m (47 to 53 lb ft). Install governor sleeve (14).
Illustration 8 g02805641
Note: Apply engine oil to all internal parts of governor.
11. Install O-ring seals on governor lever assembly (13). Position governor lever assembly (13)
into the governor housing and install spring (12).
12. Install spring (11) and speed control lever (9) on governor lever assembly (13).
13. Install pin (10) into governor lever assembly (13).
4/6
277D Multi Terrain Loader MLT00001-UP (MACHINE) POWERED BY C3.3B Engi...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 9 g02805640
14. Position governor lever (8). Install shaft (6) and spring (7) in governor housing assembly
(3).
15. If necessary, replace O-ring seal (5) with new. Install O-ring seal (5) in governor housing
assembly (3).
Illustration 10 g02805639
16. Use a suitable blocking to support the fuel injection pump and governor. Position governor
housing assembly (3) and install bolts (4). Tighten bolts (4) to a torque of 10 to 11 N·m
(87 to 100 lb in).
Illustration 11 g02805638
17. Inspect fuel injection pump and governor (1) for installation.
18. Install tube (2).
End By:
a. Install fuel injection pump and governor.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Mon Nov 4 08:39:14 UTC+0800 2019
5/6
277D Multi Terrain Loader MLT00001-UP (MACHINE) POWERED BY C3.3B Engi...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 1 g03177762
1. If necessary, install studs (10) and remove cover (11).
Illustration 2 g03177759
2. Install the O-ring seal on fuel injection pump and governor (9). Position fuel injection pump
and governor (9) onto the flywheel housing.
3. Install three nuts (8) to fuel injection pump and governor (9). Tighten nuts (8) to a torque of
18 to 20 N·m (159 ± 177 lb in).
Illustration 3 g03177783
3/4
277D Multi Terrain Loader MLT00001-UP (MACHINE) POWERED BY C3.3B Engi...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. 4. Apply engine oil to threads and torque fitting (7) to a torque of 16 to 19 N·m (12 to 14 lb ft).
5. Install engine oil pressure sensor (6) and connect the wiring harness assembly. Tighten the
engine oil pressure sensor (6) to a torque of 15 to 19 N·m (11 to 14 lb ft).
Illustration 4 g02804519
6. Position bracket (3) and install two nuts (4) and two bolts (5).
Illustration 5 g02804516
7. Check the timing marks and install the O-ring seal and oil plug cap (1). Install the O-ring
seal and cover (2) on flywheel housing (3).
End By:
a. Install the fuel injection lines.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Nov 4 08:40:14 UTC+0800 2019
4/4
277D Multi Terrain Loader MLT00001-UP (MACHINE) POWERED BY C3.3B Engi...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: MULTI TERRAIN LOADER
Model: 277D MULTI TERRAIN LOADER MLT
Configuration: 277D Multi Terrain Loader MLT00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
C2.6 and C3.3B Engines for Caterpillar Built Machines
Media Number -UENR0137-11 Publication Date -01/08/2015 Date Updated -12/07/2018
i05242455
Fuel Injection Pump - Remove and Install
SMCS - 1251-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 390-1150 Injection Pump Gear Puller 1
Start By:
a. Remove fuel injection line.
Note: Refer to Specification UENR0995 "Engine Design" for non-specified engine Torque
Values.
1. Turn the fuel supply to the OFF position.
2. Turn the battery disconnect switch to the OFF position.
1/5
277D Multi Terrain Loader MLT00001-UP (MACHINE) POWERED BY C3.3B Engi...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 1 g02781037
3. Disconnect hose assembly (2) from fuel injection pump (1).
4. Remove sight cover (3) from fuel injection pump (1).
Illustration 2 g02874459
5. Remove the shutoff solenoid and cover (1A). Install Tooling (A) to hold back the governor
control arm and assist removing the spring (5) and nut (4).
Illustration 3 g02781105
6. Disconnect spring (5) and attach a thin wire to spring (5). Remove nut (4). Position the lever
off the stud.
Personal injury can result from parts and/or covers under spring
pressure.
Spring force will be released when covers are removed.
Be prepared to hold spring loaded covers as the bolts are loosened.
2/5
277D Multi Terrain Loader MLT00001-UP (MACHINE) POWERED BY C3.3B Engi...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. 7. Remove two nuts (6) and four bolts (7) from fuel injection pump (1). The fuel injection
pump (1) is spring loaded.
8. Carefully remove fuel injection pump (1) from the fuel injection pump housing.
Illustration 4 g02781040
9. Remove gasket shims (8).
10. If necessary, remove studs (9) from the fuel injection pump housing.
11. To secure the spring from falling inside the housing use wire (10).
12. Clean fuel injection pump (1) and the area around the fuel injection pump. Ensure that the
area is free from contamination before beginning installation.
Installation Procedure
NOTICE
Refer to System Operation, Testing and Adjusting, "Cleanliness of
Fuel System Components" for detailed information on the standards of
cleanliness that must be observed during ALL work on the fuel system.
3/5
277D Multi Terrain Loader MLT00001-UP (MACHINE) POWERED BY C3.3B Engi...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 5 g02781040
1. Keep wire (10) secure to the spring to prevent falling into the housing.
2. If necessary, install studs (9) into the fuel injection pump housing.
3. Position new gasket shims (8) onto the fuel injection pump housing.
Note: When you disassemble or replace, make sure that you use the same number of new
gasket shims with the same thickness.
Illustration 6 g02781105
4. Carefully install fuel injection pump (1) into the fuel injection pump housing .
5. Install four new bolts (7) into fuel injection pump (1). Install two nuts (6) into fuel injection
pump (1). Tighten bolts (7) to a torque of 24 to 27 N·m (214 to 240 lb in). Tighten nuts (6)
to a torque of 18 to 20 N·m (159 to 178 lb in).
4/5
277D Multi Terrain Loader MLT00001-UP (MACHINE) POWERED BY C3.3B Engi...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 7 g02781722
6. Position the lever on the stud. Install nut (4) to hold the lever in place. Tighten nut (4) to a
torque of 3 to 4 N·m (26 to 36 lb in).
7. Connect spring (5) with the thin wire.
Illustration 8 g02781037
8. Install sight cover (3).
9. Connect hose assembly (2) to fuel injection pump (1).
10. Turn the fuel supply to the ON position.
11. Turn the battery disconnect switch to the ON position.
12. After replacement of the fuel injection pump, the fuel injection pump must be calibrated.
Refer to System Operation, Testing and Adjusting, "Fuel Injection Timing - Check".
End By:
a. Install fuel injection lines.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Nov 4 08:41:13 UTC+0800 2019
5/5
277D Multi Terrain Loader MLT00001-UP (MACHINE) POWERED BY C3.3B Engi...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
20. Illustration 1 g02782212
1. Disconnect hose assembly (2) from turbocharger (1).
2. Remove tube assembly (3) from turbocharger (1).
3. Remove bolt (4) and the four lower bolts. Remove tube assemblies (5) and the gasket and
the O-ring seal.
Illustration 2 g02782214
4. Remove five bolts (7) and housing (8) and the gasket.
5. Remove four nuts (6) and turbocharger (1) and the gasket.
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite C5A 1
3/5
277D Multi Terrain Loader MLT00001-UP (MACHINE) POWERED BY C3.3B Engi...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 3 g02782214
1. If necessary, install new gaskets.
2. Position the gasket and install turbocharger (1) on the exhaust manifold.
3. Position the gasket and install housing (8) on the turbocharger (1) and install three bolts (7)
to align turbocharger (1).
4. Apply Tooling (A) to three nuts (6) and install three nuts (6) on turbocharger (1). Tighten
three nuts (6) and remove three bolts (7) and housing (8).
5. Apply Tooling (A) to one nut (6) and install one nut (6) on turbocharger (1). Tighten one
nut (6).
6. Position the gasket and housing (8). Apply Tooling (A) on bolts (7) and install five bolts (7)
and tighten.
Illustration 4 g02782212
7. Position tube assemblies (5) and the gasket and the O-ring seal and install four lower bolts
and bolt (4). Tighten bolt (4) to a torque of 16.0 ± 19.0 N·m (11.80 ± 14.01 lb ft).
8. Position tube assembly (3) on turbocharger (1) and install the clamps.
9. Connect hose assembly (2) on turbocharger (1).
Mon Nov 4 08:42:12 UTC+0800 2019
4/5
277D Multi Terrain Loader MLT00001-UP (MACHINE) POWERED BY C3.3B Engi...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Note: Refer to Specification UENR0995 "Engine Design" for non-specified engine Torque
Values.
Illustration 1 g02770916
1. Remove two locknuts (4) and six bolts (3).
2. Remove exhaust manifold (1) and the gasket.
3. If necessary, remove studs (2) and (5).
Installation Procedure
1. Install exhaust manifold (1) in the reverse order of removal.
a. If necessary, apply Tooling (A) on the threads of studs (5) and (2).
b. Apply Tooling (A) on the threads of locknuts (4) and the threads of bolts (3).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Nov 4 08:43:11 UTC+0800 2019
3/3
277D Multi Terrain Loader MLT00001-UP (MACHINE) POWERED BY C3.3B Engi...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...