The document provides instructions for disassembling and assembling the fuel injection pump and governor of a 246D Skid Steer Loader. It describes 17 steps to disassemble the components, including using specific tools to remove gears, shafts, springs, and bearings. It then describes 18 steps for reassembling the components in reverse order, noting specific torque specifications. The purpose is to repair or replace parts of the fuel injection pump and governor system.
Caterpillar cat 246 d skid steer loader (prefix hmr) service repair manual (h...fjjsefkkertsemme
This document provides instructions for removing and installing a fuel injection pump on a 246D Skid Steer Loader powered by a C3.3B engine. The procedure involves disconnecting fuel lines, removing mounting bolts and nuts, and cleaning components. When installing, new gasket shims are used and bolts are tightened to the specified torques. Special care must be taken when removing the spring-loaded fuel injection pump.
Caterpillar cat 246 d skid steer loader (prefix hmr) service repair manual (h...fjsjkseikdmme
This document provides instructions for removing and installing a fuel injection pump on a 246D Skid Steer Loader powered by a C3.3B engine. The steps include disconnecting the fuel line, removing the sight cover and solenoid. Nuts and bolts are removed to take off the pump which is spring loaded. Gasket shims and studs if needed are installed before reinstalling the pump, lever, spring and sight cover. Cleanliness of fuel system components is emphasized.
Caterpillar cat 246 d skid steer loader (prefix hmr) service repair manual (h...fjjsefkksemm
The document provides instructions for removing and installing a fuel injection pump on a 246D Skid Steer Loader powered by a C3.3B engine. It describes:
1) Disconnecting the fuel line and removing the sight cover from the fuel injection pump.
2) Using a special tool to hold the governor control arm while removing the spring and nut.
3) Positioning the lever and removing additional parts from the pump.
4) Reversing the removal steps for installation, ensuring proper torque of fasteners.
The document provides instructions for disassembling and assembling a fuel injection pump and governor for a 246D Skid Steer Loader. The disassembly procedure involves removing 17 parts including the governor housing assembly, shaft, spring, and fuel camshaft. The assembly procedure instructs installing these 17 parts in reverse order and provides torque specifications for nuts and bolts. Additionally, the document describes removing and installing the entire fuel injection pump, removing fuel lines, and cleaning parts.
The document provides instructions for disassembling and assembling a fuel injection pump and governor for a 246D Skid Steer Loader. The disassembly procedure involves removing 17 parts including the governor housing assembly, shaft, spring, and fuel camshaft. The assembly procedure instructs installing these 17 parts in reverse order and provides torque specifications for nuts and bolts. Additionally, the document describes removing and installing the entire fuel injection pump, removing fuel lines, and cleaning parts.
The document provides instructions for disassembling and assembling a fuel injection pump and governor for a 246D Skid Steer Loader. The disassembly procedure involves removing 17 parts including the governor housing assembly, shaft, spring, and fuel camshaft. The assembly procedure instructs installing these 17 parts in reverse order and provides torque specifications for nuts and bolts. Additionally, the document describes removing and installing the entire fuel injection pump, removing fuel lines, and cleaning parts.
1) The document provides instructions for disassembling and assembling the fuel injection pump and governor for a 242D Skid Steer Loader.
2) The disassembly procedure involves removing 17 parts including the governor housing assembly, shaft, springs, and fuel camshaft.
3) The assembly procedure instructs installing the parts in reverse order and provides torque specifications for tightening bolts and nuts.
This document provides instructions for disassembling and assembling the fuel injection pump and governor for a 242D Skid Steer Loader. The disassembly process involves removing 17 parts from the fuel injection pump and governor assembly including bolts, seals, shafts, springs, levers and gears. The assembly process describes installing these 17 parts in reverse order and provides torque specifications for certain bolts and nuts. Tools including an injection pump gear puller and bearing puller are required.
Caterpillar cat 246 d skid steer loader (prefix hmr) service repair manual (h...fjjsefkkertsemme
This document provides instructions for removing and installing a fuel injection pump on a 246D Skid Steer Loader powered by a C3.3B engine. The procedure involves disconnecting fuel lines, removing mounting bolts and nuts, and cleaning components. When installing, new gasket shims are used and bolts are tightened to the specified torques. Special care must be taken when removing the spring-loaded fuel injection pump.
Caterpillar cat 246 d skid steer loader (prefix hmr) service repair manual (h...fjsjkseikdmme
This document provides instructions for removing and installing a fuel injection pump on a 246D Skid Steer Loader powered by a C3.3B engine. The steps include disconnecting the fuel line, removing the sight cover and solenoid. Nuts and bolts are removed to take off the pump which is spring loaded. Gasket shims and studs if needed are installed before reinstalling the pump, lever, spring and sight cover. Cleanliness of fuel system components is emphasized.
Caterpillar cat 246 d skid steer loader (prefix hmr) service repair manual (h...fjjsefkksemm
The document provides instructions for removing and installing a fuel injection pump on a 246D Skid Steer Loader powered by a C3.3B engine. It describes:
1) Disconnecting the fuel line and removing the sight cover from the fuel injection pump.
2) Using a special tool to hold the governor control arm while removing the spring and nut.
3) Positioning the lever and removing additional parts from the pump.
4) Reversing the removal steps for installation, ensuring proper torque of fasteners.
The document provides instructions for disassembling and assembling a fuel injection pump and governor for a 246D Skid Steer Loader. The disassembly procedure involves removing 17 parts including the governor housing assembly, shaft, spring, and fuel camshaft. The assembly procedure instructs installing these 17 parts in reverse order and provides torque specifications for nuts and bolts. Additionally, the document describes removing and installing the entire fuel injection pump, removing fuel lines, and cleaning parts.
The document provides instructions for disassembling and assembling a fuel injection pump and governor for a 246D Skid Steer Loader. The disassembly procedure involves removing 17 parts including the governor housing assembly, shaft, spring, and fuel camshaft. The assembly procedure instructs installing these 17 parts in reverse order and provides torque specifications for nuts and bolts. Additionally, the document describes removing and installing the entire fuel injection pump, removing fuel lines, and cleaning parts.
The document provides instructions for disassembling and assembling a fuel injection pump and governor for a 246D Skid Steer Loader. The disassembly procedure involves removing 17 parts including the governor housing assembly, shaft, spring, and fuel camshaft. The assembly procedure instructs installing these 17 parts in reverse order and provides torque specifications for nuts and bolts. Additionally, the document describes removing and installing the entire fuel injection pump, removing fuel lines, and cleaning parts.
1) The document provides instructions for disassembling and assembling the fuel injection pump and governor for a 242D Skid Steer Loader.
2) The disassembly procedure involves removing 17 parts including the governor housing assembly, shaft, springs, and fuel camshaft.
3) The assembly procedure instructs installing the parts in reverse order and provides torque specifications for tightening bolts and nuts.
This document provides instructions for disassembling and assembling the fuel injection pump and governor for a 242D Skid Steer Loader. The disassembly process involves removing 17 parts from the fuel injection pump and governor assembly including bolts, seals, shafts, springs, levers and gears. The assembly process describes installing these 17 parts in reverse order and provides torque specifications for certain bolts and nuts. Tools including an injection pump gear puller and bearing puller are required.
Caterpillar Cat 320D L Excavator (Prefix PHX) Service Repair Manual (PHX00001...f7usueijdkdmm3e
The document provides instructions for removing and installing a flywheel on a Caterpillar 320D L excavator. It describes using various tools to remove components like the muffler, flywheel housing, and crankshaft rear seal prior to removing the flywheel. The flywheel removal procedure involves using a link bracket and forcing bolts to lift the 50 kg flywheel out of the housing. Reinstallation follows the reverse process, and technicians are advised to clean parts and check for proper installation.
Caterpillar Cat 322C FM EXCAVATOR (Prefix C3R) Service Repair Manual (C3R0000...f7usueijdkdmm3e
The document provides instructions for removing and installing a unit injector hydraulic pump on a 322C FM EXCAVATOR C3R powered by a 3126B engine. The removal procedure involves disconnecting hoses and lines, removing bolts, and taking off the pump. The installation procedure specifies lubricating seals, installing bolts, reconnecting lines and hoses, and ensuring connections are secure. Separate sections provide instructions for disassembling and assembling a turbocharger on the same engine model.
This document provides instructions for removing and installing a flywheel housing on a 416C Backhoe Loader with a 3054 engine. It describes using lifting brackets and removing mounting bolts to detach the housing. Cleaning surfaces and replacing seals is emphasized. Diagrams illustrate the component locations and tooling. Proper safety practices like fluid containment are noted.
This document provides instructions for removing the crankshaft front seal from a Caterpillar C6.4 engine. The procedure involves using a slide hammer puller tool to remove the seal from the front of the crankshaft. Technicians are advised to keep all parts clean and contain fluids properly during repair work. Removal of the seal prepares the engine for further disassembly or repair of crankshaft components.
This document provides instructions for removing and installing the flywheel housing on a Caterpillar 3054 engine. The removal procedure involves removing mounting bolts from the top and bottom of the housing and using lifting tools to detach the housing from the cylinder block. The installation procedure specifies cleaning parts, placing the housing in position, and tightening mounting bolts to specified torques. Tools and safety precautions are also listed.
This document provides instructions for removing and installing exhaust manifolds and inlet manifolds on Caterpillar 3054 engines. It describes the removal and installation procedures for both Type 1/9RM and Type 2/7BJ engines. The procedures involve removing bolts and nuts, inspecting and replacing gaskets if needed, and reinstalling components in the reverse order of removal while keeping parts clean from contaminants. Diagrams illustrate the components and numbered steps in the procedures.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix MY2) Service Repair ...f7usueijdkdmm3e
The document provides instructions for servicing components of a 308E2CR Mini Hydraulic Excavator engine. It includes procedures for removing and installing components like the exhaust gas recirculation valve, fumes disposal filter, exhaust manifold, and diesel particulate filter. Safety precautions are provided, and the work is to be done in the specified order while applying any recommended lubricants to bolts or studs.
This document provides instructions for removing and installing an engine from a 420F2 backhoe loader. It outlines 19 steps to remove the engine, which includes draining fluids, disconnecting various components like hoses and electrical connections, and removing mounting hardware. It then describes 19 steps to install the engine in reverse order, including filling fluids and reconnecting all components. The document is part of a service repair manual and focuses on a specific model, engine, and component.
This document provides instructions for removing and installing an engine in a 420F2 backhoe loader. It outlines 17 steps for removing the engine, which include disconnecting wiring harnesses, hoses, and other components. It then outlines 17 steps for installing the new engine, which involve connecting all the removed components in reverse order. Tools required include a hydraulic jack and load leveling beam to lift the heavy engine. Safety notices are provided to keep components clean and contain fluids.
The document provides instructions for removing and installing a crankshaft rear seal on a Caterpillar 3054C engine. It describes using guide bolts and a link bracket to support the flywheel during removal. The crankshaft rear seal is non-serviceable and must be replaced with the housing assembly. The new seal assembly is installed with a plastic sleeve to protect the seal lip and set screws are used to secure it to the cylinder block.
The document provides instructions for removing and installing a flywheel housing on a 422E Backhoe Loader. Key steps include:
1. Removing the flywheel, bolts, and lifting the housing off the engine block using lifting devices.
2. Inspecting the crankshaft rear seal for leaks before installing a cleaned housing with dowels and bolts, checking alignment with a dial indicator.
3. Reinstalling the flywheel to complete the process.
The document provides instructions for removing and installing a flywheel housing on a 320D L excavator. The removal procedure involves using a link bracket and lifting device to remove the flywheel housing after removing bolts and washers. The installation procedure instructs to clean parts, apply retaining compound, and use the link bracket to reinstall the flywheel housing and check that the oil seal is correctly installed.
This service repair manual provides instructions for installing an engine on a 416F2 Backhoe Loader. It details 17 steps for installing the engine, including attaching the engine to a lifting device, aligning and bolting components like the bell housing and flywheel, installing engine mounts and panels, connecting wiring harnesses and lines, and filling fluids. The manual also provides supplemental documents for removing and installing additional engine components like the fuel pump, fuel lines, and fuel injector nozzles.
This document provides instructions for removing and installing various engine components on a Caterpillar 3054C engine, including:
- Lifters can be removed and installed using a telescoping magnet, ensuring they are replaced in the original location.
- The camshaft can be removed after other components and installed after cleaning, taking care not to damage lobes or bearings.
- Camshaft bearings are removed and installed using a special tool, aligning the oil hole with the cylinder block.
- The engine oil pan is removed after draining oil, then cleaned and reinstalled using new gaskets and sealant. Proper support of heavy parts is advised.
Caterpillar Cat 307 EXCAVATOR (Prefix 2WM) Service Repair Manual (2WM00001-00...f7usueijdkdmm3e
This document provides instructions for removing and installing pistons, connecting rods, and connecting rod bearings on a 307 excavator. The summary is:
1) Remove the cylinder head, engine oil pump, and piston cooling jets to access the connecting rods. Rotate the crankshaft to position the pistons for removal.
2) Remove the connecting rod caps, bolts or nuts, and bearings to separate the connecting rods from the pistons. Push the pistons and rods out of the cylinder block.
3) Clean all components thoroughly before disassembling and assembling. Lubricate parts with clean engine oil during installation.
This document provides instructions for removing and installing various engine components on a 246 Skid Steer Loader, including:
- Removing and installing the turbocharger
- Removing and installing the exhaust manifold
- Removing the inlet manifold
- Installing the inlet manifold
- Removing and installing inlet and exhaust valve springs
The document includes illustrations and multistep procedures for each component, with notices about keeping parts clean and containing fluids.
This document provides instructions for servicing components of a 246D Skid Steer Loader powered by a C3.3B engine. It includes procedures for removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures note important steps like ensuring parts are clean, applying lubricants, using the proper tools, and torquing fasteners to the specified values. Cautions are also provided regarding containing fluids and proper fluid disposal.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix TMX) Service Repair ...f7usueijdkdmm3e
The document provides instructions for removing and installing various engine components on a 308E2CR Mini Hydraulic Excavator including the crankshaft front seal, idler gear, housing (front), and valve mechanism cover. The procedures include draining fluids, loosening bolts, using specialized tools, cleaning surfaces, applying sealant, and tightening bolts to specified torques.
This document provides instructions for removing and installing exhaust manifolds, inlet and exhaust valves, and inlet and exhaust valve springs on Caterpillar 249D compact track loaders. The procedures describe using various tools to compress springs, remove bolts and nuts, and install new gaskets. Safety notices are included to warn technicians to keep parts clean, plug openings, and wear protective equipment when working with compressed springs.
This service repair manual provides instructions for removing and installing the fuel injection pump on Caterpillar 3054 engines. The document outlines the required tools and steps to:
1) Remove the fuel injection pump by loosening locking screws, aligning timing holes, and removing mounting bolts and nuts.
2) Install the fuel injection pump by checking and installing o-rings, aligning timing marks, inserting timing pins, and tightening mounting hardware while ensuring proper timing.
3) The process involves precautions like keeping parts clean, containing fluids, and setting the engine to top dead center for timing.
Caterpillar Cat 320D L Excavator (Prefix PHX) Service Repair Manual (PHX00001...f7usueijdkdmm3e
The document provides instructions for removing and installing a flywheel on a Caterpillar 320D L excavator. It describes using various tools to remove components like the muffler, flywheel housing, and crankshaft rear seal prior to removing the flywheel. The flywheel removal procedure involves using a link bracket and forcing bolts to lift the 50 kg flywheel out of the housing. Reinstallation follows the reverse process, and technicians are advised to clean parts and check for proper installation.
Caterpillar Cat 322C FM EXCAVATOR (Prefix C3R) Service Repair Manual (C3R0000...f7usueijdkdmm3e
The document provides instructions for removing and installing a unit injector hydraulic pump on a 322C FM EXCAVATOR C3R powered by a 3126B engine. The removal procedure involves disconnecting hoses and lines, removing bolts, and taking off the pump. The installation procedure specifies lubricating seals, installing bolts, reconnecting lines and hoses, and ensuring connections are secure. Separate sections provide instructions for disassembling and assembling a turbocharger on the same engine model.
This document provides instructions for removing and installing a flywheel housing on a 416C Backhoe Loader with a 3054 engine. It describes using lifting brackets and removing mounting bolts to detach the housing. Cleaning surfaces and replacing seals is emphasized. Diagrams illustrate the component locations and tooling. Proper safety practices like fluid containment are noted.
This document provides instructions for removing the crankshaft front seal from a Caterpillar C6.4 engine. The procedure involves using a slide hammer puller tool to remove the seal from the front of the crankshaft. Technicians are advised to keep all parts clean and contain fluids properly during repair work. Removal of the seal prepares the engine for further disassembly or repair of crankshaft components.
This document provides instructions for removing and installing the flywheel housing on a Caterpillar 3054 engine. The removal procedure involves removing mounting bolts from the top and bottom of the housing and using lifting tools to detach the housing from the cylinder block. The installation procedure specifies cleaning parts, placing the housing in position, and tightening mounting bolts to specified torques. Tools and safety precautions are also listed.
This document provides instructions for removing and installing exhaust manifolds and inlet manifolds on Caterpillar 3054 engines. It describes the removal and installation procedures for both Type 1/9RM and Type 2/7BJ engines. The procedures involve removing bolts and nuts, inspecting and replacing gaskets if needed, and reinstalling components in the reverse order of removal while keeping parts clean from contaminants. Diagrams illustrate the components and numbered steps in the procedures.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix MY2) Service Repair ...f7usueijdkdmm3e
The document provides instructions for servicing components of a 308E2CR Mini Hydraulic Excavator engine. It includes procedures for removing and installing components like the exhaust gas recirculation valve, fumes disposal filter, exhaust manifold, and diesel particulate filter. Safety precautions are provided, and the work is to be done in the specified order while applying any recommended lubricants to bolts or studs.
This document provides instructions for removing and installing an engine from a 420F2 backhoe loader. It outlines 19 steps to remove the engine, which includes draining fluids, disconnecting various components like hoses and electrical connections, and removing mounting hardware. It then describes 19 steps to install the engine in reverse order, including filling fluids and reconnecting all components. The document is part of a service repair manual and focuses on a specific model, engine, and component.
This document provides instructions for removing and installing an engine in a 420F2 backhoe loader. It outlines 17 steps for removing the engine, which include disconnecting wiring harnesses, hoses, and other components. It then outlines 17 steps for installing the new engine, which involve connecting all the removed components in reverse order. Tools required include a hydraulic jack and load leveling beam to lift the heavy engine. Safety notices are provided to keep components clean and contain fluids.
The document provides instructions for removing and installing a crankshaft rear seal on a Caterpillar 3054C engine. It describes using guide bolts and a link bracket to support the flywheel during removal. The crankshaft rear seal is non-serviceable and must be replaced with the housing assembly. The new seal assembly is installed with a plastic sleeve to protect the seal lip and set screws are used to secure it to the cylinder block.
The document provides instructions for removing and installing a flywheel housing on a 422E Backhoe Loader. Key steps include:
1. Removing the flywheel, bolts, and lifting the housing off the engine block using lifting devices.
2. Inspecting the crankshaft rear seal for leaks before installing a cleaned housing with dowels and bolts, checking alignment with a dial indicator.
3. Reinstalling the flywheel to complete the process.
The document provides instructions for removing and installing a flywheel housing on a 320D L excavator. The removal procedure involves using a link bracket and lifting device to remove the flywheel housing after removing bolts and washers. The installation procedure instructs to clean parts, apply retaining compound, and use the link bracket to reinstall the flywheel housing and check that the oil seal is correctly installed.
This service repair manual provides instructions for installing an engine on a 416F2 Backhoe Loader. It details 17 steps for installing the engine, including attaching the engine to a lifting device, aligning and bolting components like the bell housing and flywheel, installing engine mounts and panels, connecting wiring harnesses and lines, and filling fluids. The manual also provides supplemental documents for removing and installing additional engine components like the fuel pump, fuel lines, and fuel injector nozzles.
This document provides instructions for removing and installing various engine components on a Caterpillar 3054C engine, including:
- Lifters can be removed and installed using a telescoping magnet, ensuring they are replaced in the original location.
- The camshaft can be removed after other components and installed after cleaning, taking care not to damage lobes or bearings.
- Camshaft bearings are removed and installed using a special tool, aligning the oil hole with the cylinder block.
- The engine oil pan is removed after draining oil, then cleaned and reinstalled using new gaskets and sealant. Proper support of heavy parts is advised.
Caterpillar Cat 307 EXCAVATOR (Prefix 2WM) Service Repair Manual (2WM00001-00...f7usueijdkdmm3e
This document provides instructions for removing and installing pistons, connecting rods, and connecting rod bearings on a 307 excavator. The summary is:
1) Remove the cylinder head, engine oil pump, and piston cooling jets to access the connecting rods. Rotate the crankshaft to position the pistons for removal.
2) Remove the connecting rod caps, bolts or nuts, and bearings to separate the connecting rods from the pistons. Push the pistons and rods out of the cylinder block.
3) Clean all components thoroughly before disassembling and assembling. Lubricate parts with clean engine oil during installation.
This document provides instructions for removing and installing various engine components on a 246 Skid Steer Loader, including:
- Removing and installing the turbocharger
- Removing and installing the exhaust manifold
- Removing the inlet manifold
- Installing the inlet manifold
- Removing and installing inlet and exhaust valve springs
The document includes illustrations and multistep procedures for each component, with notices about keeping parts clean and containing fluids.
This document provides instructions for servicing components of a 246D Skid Steer Loader powered by a C3.3B engine. It includes procedures for removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures note important steps like ensuring parts are clean, applying lubricants, using the proper tools, and torquing fasteners to the specified values. Cautions are also provided regarding containing fluids and proper fluid disposal.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix TMX) Service Repair ...f7usueijdkdmm3e
The document provides instructions for removing and installing various engine components on a 308E2CR Mini Hydraulic Excavator including the crankshaft front seal, idler gear, housing (front), and valve mechanism cover. The procedures include draining fluids, loosening bolts, using specialized tools, cleaning surfaces, applying sealant, and tightening bolts to specified torques.
This document provides instructions for removing and installing exhaust manifolds, inlet and exhaust valves, and inlet and exhaust valve springs on Caterpillar 249D compact track loaders. The procedures describe using various tools to compress springs, remove bolts and nuts, and install new gaskets. Safety notices are included to warn technicians to keep parts clean, plug openings, and wear protective equipment when working with compressed springs.
This service repair manual provides instructions for removing and installing the fuel injection pump on Caterpillar 3054 engines. The document outlines the required tools and steps to:
1) Remove the fuel injection pump by loosening locking screws, aligning timing holes, and removing mounting bolts and nuts.
2) Install the fuel injection pump by checking and installing o-rings, aligning timing marks, inserting timing pins, and tightening mounting hardware while ensuring proper timing.
3) The process involves precautions like keeping parts clean, containing fluids, and setting the engine to top dead center for timing.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Real-time driver monitoring is one of the easiest ways to make fleet management efficient as well as seamless. Connected vehicle solutions such as fleet GPS trackers and associated software help businesses in several ways. Refer to the post below for more details.
2. Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 246D SKID STEER LOADER HMR
Configuration: 246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
C2.6 and C3.3B Engines for Caterpillar Built Machines
Media Number -UENR0137-11 Publication Date -01/08/2015 Date Updated -12/07/2018
i05242439
Fuel Injection Pump and Governor - Disassemble
SMCS - 1286-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
390-1150 Injection Pump Gear Puller 1
154-6360 Bolt 1
B 8H-0663 Bearing Puller 1
Start By:
a. Remove fuel injection pump and governor.
Illustration 1 g02805638
1/6
246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. 1. Inspect fuel injection pump and governor (1).
2. Remove tube (2).
Illustration 2 g02805639
3. Use suitable blocking and position the fuel injection pump and governor. Remove bolts (4)
and remove governor housing assembly (3).
4. Remove two bolts (4B) and remove stop solenoid (4A). Replace o-ring if necessary.
Illustration 3 g02805640
5. Remove and inspect O-ring seal (5) from governor housing assembly (3). If necessary,
replace O-ring seal (5) with new.
6. Remove shaft (6) and spring (7) from governor housing assembly (3). Remove governor
lever (8).
2/6
246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 4 g02805641
7. Remove pin (10) from governor lever assembly (12).
8. Remove speed control lever (9) and spring (11) from governor lever assembly (12).
9. Remove spring (13) and remove governor lever assembly (12) with the O-ring seals.
Illustration 5 g02805656
Illustration 6 g02805658
10. Remove governor sleeve (13) and nut (16). Remove governor weights (15).
3/6
246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 7 g02805660
Illustration 8 g02805696
11. Remove nut (17) from gear (18).
Note: Nut (17) has reverse threads.
12. Use Tooling (A) to remove gear (18).
Illustration 9 g02805716
13. Remove bolts (19) and retaining plate (20).
14. Remove fuel camshaft (24) from the housing assembly.
4/6
246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 15. Remove screws (21) and retaining plate (22). If necessary, replace key (23) with new.
Illustration 10 g02805762
Illustration 11 g02805764
Illustration 12 g02805765
16. Use a suitable press and Tooling (B) to remove bearing (25) from fuel camshaft (24) and
ring (27).
17. Use a suitable press and Tooling (B) to remove bearing (26) from fuel camshaft (24).
5/6
246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 246D SKID STEER LOADER HMR
Configuration: 246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
C2.6 and C3.3B Engines for Caterpillar Built Machines
Media Number -UENR0137-11 Publication Date -01/08/2015 Date Updated -12/07/2018
i05242445
Fuel Injection Pump and Governor - Assemble
SMCS - 1286-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
390-1150 Injection Pump Gear Puller 1
154-6360 Bolt 1
B 8H-0663 Bearing Puller 1
Note: Refer to Specification UENR0995 "Engine Design" for non-specified engine Torque
Values.
Illustration 1 g02805765
1/6
246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 2 g02807019
Illustration 3 g02807020
1. Use Tooling (B) and a suitable press to install bearings (26) onto fuel camshaft (24).
2. Position ring (27). Use Tooling (B) and a suitable press to install bearings (25) onto fuel
camshaft (24).
Illustration 4 g02805716
3. If necessary, replace key (23) with new. Position retaining plate (22) and install screws (21).
Tighten screws (21) to a torque of 3.9 to 4.2 N·m (34.5 to 37.4 lb in).
2/6
246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 4. Position fuel camshaft (24) in the housing assembly.
5. Position retaining plate (20) and install bolts (19). Tighten bolts (19) to a torque of
10 to 11 N·m (87 to 100 lb in).
Illustration 5 g02805660
6. Install gear (18).
7. Install nut (17) to gear (18).
8. For the C3.3B Tighten nut (17) to a torque of 138 to 156 N·m (102 to 115 lb ft).
9. For the C2.6 Tighten nut (17) to a torque of 93 to 102 N·m (69 to 75 lb ft).
Illustration 6 g02805658
3/6
246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 7 g02805656
10. Position governor weights (15) and install nut (16). Tighten nut (16) to a torque of
63 to 72 N·m (47 to 53 lb ft). Install governor sleeve (14).
Illustration 8 g02805641
Note: Apply engine oil to all internal parts of governor.
11. Install O-ring seals on governor lever assembly (13). Position governor lever assembly (13)
into the governor housing and install spring (12).
12. Install spring (11) and speed control lever (9) on governor lever assembly (13).
13. Install pin (10) into governor lever assembly (13).
4/6
246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 9 g02805640
14. Position governor lever (8). Install shaft (6) and spring (7) in governor housing assembly
(3).
15. If necessary, replace O-ring seal (5) with new. Install O-ring seal (5) in governor housing
assembly (3).
Illustration 10 g02805639
16. Use a suitable blocking to support the fuel injection pump and governor. Position governor
housing assembly (3) and install bolts (4). Tighten bolts (4) to a torque of 10 to 11 N·m
(87 to 100 lb in).
Illustration 11 g02805638
17. Inspect fuel injection pump and governor (1) for installation.
18. Install tube (2).
End By:
a. Install fuel injection pump and governor.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Mon Nov 11 23:39:45 UTC+0800 2019
5/6
246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 1 g03177762
1. If necessary, install studs (10) and remove cover (11).
Illustration 2 g03177759
2. Install the O-ring seal on fuel injection pump and governor (9). Position fuel injection pump
and governor (9) onto the flywheel housing.
3. Install three nuts (8) to fuel injection pump and governor (9). Tighten nuts (8) to a torque of
18 to 20 N·m (159 ± 177 lb in).
Illustration 3 g03177783
3/4
246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. 4. Apply engine oil to threads and torque fitting (7) to a torque of 16 to 19 N·m (12 to 14 lb ft).
5. Install engine oil pressure sensor (6) and connect the wiring harness assembly. Tighten the
engine oil pressure sensor (6) to a torque of 15 to 19 N·m (11 to 14 lb ft).
Illustration 4 g02804519
6. Position bracket (3) and install two nuts (4) and two bolts (5).
Illustration 5 g02804516
7. Check the timing marks and install the O-ring seal and oil plug cap (1). Install the O-ring
seal and cover (2) on flywheel housing (3).
End By:
a. Install the fuel injection lines.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Nov 11 23:40:41 UTC+0800 2019
4/4
246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 246D SKID STEER LOADER HMR
Configuration: 246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
C2.6 and C3.3B Engines for Caterpillar Built Machines
Media Number -UENR0137-11 Publication Date -01/08/2015 Date Updated -12/07/2018
i05242455
Fuel Injection Pump - Remove and Install
SMCS - 1251-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 390-1150 Injection Pump Gear Puller 1
Start By:
a. Remove fuel injection line.
Note: Refer to Specification UENR0995 "Engine Design" for non-specified engine Torque
Values.
1. Turn the fuel supply to the OFF position.
2. Turn the battery disconnect switch to the OFF position.
1/5
246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 1 g02781037
3. Disconnect hose assembly (2) from fuel injection pump (1).
4. Remove sight cover (3) from fuel injection pump (1).
Illustration 2 g02874459
5. Remove the shutoff solenoid and cover (1A). Install Tooling (A) to hold back the governor
control arm and assist removing the spring (5) and nut (4).
Illustration 3 g02781105
6. Disconnect spring (5) and attach a thin wire to spring (5). Remove nut (4). Position the lever
off the stud.
Personal injury can result from parts and/or covers under spring
pressure.
Spring force will be released when covers are removed.
Be prepared to hold spring loaded covers as the bolts are loosened.
2/5
246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. 7. Remove two nuts (6) and four bolts (7) from fuel injection pump (1). The fuel injection
pump (1) is spring loaded.
8. Carefully remove fuel injection pump (1) from the fuel injection pump housing.
Illustration 4 g02781040
9. Remove gasket shims (8).
10. If necessary, remove studs (9) from the fuel injection pump housing.
11. To secure the spring from falling inside the housing use wire (10).
12. Clean fuel injection pump (1) and the area around the fuel injection pump. Ensure that the
area is free from contamination before beginning installation.
Installation Procedure
NOTICE
Refer to System Operation, Testing and Adjusting, "Cleanliness of
Fuel System Components" for detailed information on the standards of
cleanliness that must be observed during ALL work on the fuel system.
3/5
246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 5 g02781040
1. Keep wire (10) secure to the spring to prevent falling into the housing.
2. If necessary, install studs (9) into the fuel injection pump housing.
3. Position new gasket shims (8) onto the fuel injection pump housing.
Note: When you disassemble or replace, make sure that you use the same number of new
gasket shims with the same thickness.
Illustration 6 g02781105
4. Carefully install fuel injection pump (1) into the fuel injection pump housing .
5. Install four new bolts (7) into fuel injection pump (1). Install two nuts (6) into fuel injection
pump (1). Tighten bolts (7) to a torque of 24 to 27 N·m (214 to 240 lb in). Tighten nuts (6)
to a torque of 18 to 20 N·m (159 to 178 lb in).
4/5
246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 7 g02781722
6. Position the lever on the stud. Install nut (4) to hold the lever in place. Tighten nut (4) to a
torque of 3 to 4 N·m (26 to 36 lb in).
7. Connect spring (5) with the thin wire.
Illustration 8 g02781037
8. Install sight cover (3).
9. Connect hose assembly (2) to fuel injection pump (1).
10. Turn the fuel supply to the ON position.
11. Turn the battery disconnect switch to the ON position.
12. After replacement of the fuel injection pump, the fuel injection pump must be calibrated.
Refer to System Operation, Testing and Adjusting, "Fuel Injection Timing - Check".
End By:
a. Install fuel injection lines.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Nov 11 23:41:37 UTC+0800 2019
5/5
246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 1 g02782212
1. Disconnect hose assembly (2) from turbocharger (1).
2. Remove tube assembly (3) from turbocharger (1).
3. Remove bolt (4) and the four lower bolts. Remove tube assemblies (5) and the gasket and
the O-ring seal.
Illustration 2 g02782214
4. Remove five bolts (7) and housing (8) and the gasket.
5. Remove four nuts (6) and turbocharger (1) and the gasket.
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite C5A 1
3/5
246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 3 g02782214
1. If necessary, install new gaskets.
2. Position the gasket and install turbocharger (1) on the exhaust manifold.
3. Position the gasket and install housing (8) on the turbocharger (1) and install three bolts (7)
to align turbocharger (1).
4. Apply Tooling (A) to three nuts (6) and install three nuts (6) on turbocharger (1). Tighten
three nuts (6) and remove three bolts (7) and housing (8).
5. Apply Tooling (A) to one nut (6) and install one nut (6) on turbocharger (1). Tighten one
nut (6).
6. Position the gasket and housing (8). Apply Tooling (A) on bolts (7) and install five bolts (7)
and tighten.
Illustration 4 g02782212
7. Position tube assemblies (5) and the gasket and the O-ring seal and install four lower bolts
and bolt (4). Tighten bolt (4) to a torque of 16.0 ± 19.0 N·m (11.80 ± 14.01 lb ft).
8. Position tube assembly (3) on turbocharger (1) and install the clamps.
9. Connect hose assembly (2) on turbocharger (1).
Mon Nov 11 23:42:32 UTC+0800 2019
4/5
246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 246D SKID STEER LOADER HMR
Configuration: 246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
C2.6 and C3.3B Engines for Caterpillar Built Machines
Media Number -UENR0137-11 Publication Date -01/08/2015 Date Updated -12/07/2018
i05242491
Inlet and Exhaust Valve Springs - Remove and Install
SMCS - 1108-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
7F-4292 Valve Spring Compressor 1
9U-6144 Adapter 1
Start By:
a. Remove the rocker shaft and push rod.
Note: Refer to Specification UENR0995 "Engine Design" for non-specified engine Torque
Values.
Note: The following procedure should be adopted in order to remove the valve springs when the
cylinder head is installed to the engine. Refer to Disassembly and Assembly, "Inlet and Exhaust
Valves - Remove and Install" for the procedure to remove the valve springs from a cylinder head
that has been removed from the engine.
Note: Ensure that the appropriate piston is at top dead center before the valve spring is removed.
Failure to ensure that the piston is at top dead center may allow the valve to drop into the cylinder
bore.
1/4
246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 1 g02799356
Illustration 2 g02725099
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
NOTICE
Ensure that the valve spring is compressed squarely or damage to the
valve stem may occur.
2/4
246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. 1. Follow Step 1.a through Step 1.d in order to position the appropriate piston at top dead
center.
a. Install Tooling (A) in position on the cylinder head in order to compress a valve
spring (4) for the appropriate piston.
b. Use Tooling (A) in order to compress valve spring (4) and open the valve slightly.
Note: Do not compress the spring so that valve spring retainer (3) touches the valve
stem seal.
c. Rotate the crankshaft carefully, until the piston touches the valve.
Note: Do not use excessive force to turn the crankshaft. The use of force can result in
bent valve stems.
d. Continue to rotate the crankshaft and gradually release the pressure on Tooling (A)
until the piston is at the top dead center position. The valve is now held in a position
that allows the valve spring to be safely removed.
Note: If all valve springs require replacement, the procedure can be carried out on two
cylinders at the same time. The procedure can be carried out on the following pairs of
cylinders. 1 with 4 and 2 with 3. Ensure that all of the valve springs are installed before
changing from one pair of cylinders to another pair of cylinders.
NOTICE
Do not turn the crankshaft while the valve springs are removed.
2. Remove valve cap (1). Apply sufficient pressure to Tooling (A) in order to allow removal of
valve keepers (2).
Note: Do not compress the spring so that valve spring retainer (3) touches the valve stem
seal.
3. Slowly release pressure on Tooling (A).
4. Remove valve spring retainer (3) and remove valve spring (4).
3/4
246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 3 g02725101
5. Remove Tooling (A).
6. Remove valve stem seals (5).
7. Repeat Step 2 through Step 5 in order to remove the remaining valve springs from the
appropriate cylinder.
Installation Procedure
1. Install the inlet and exhaust valve springs (4) in the reverse order of removal.
Illustration 4 g02862476
a. Install valve springs with the smaller pitch end (6) downward on cylinder head side.
b. Inspect valve springs (4) for damage and for the correct length. Refer to
Specifications, "Cylinder Head Valves " for further information.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Nov 11 23:45:20 UTC+0800 2019
4/4
246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 246D SKID STEER LOADER HMR
Configuration: 246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
C2.6 and C3.3B Engines for Caterpillar Built Machines
Media Number -UENR0137-11 Publication Date -01/08/2015 Date Updated -12/07/2018
i05242493
Inlet and Exhaust Valves - Remove and Install
SMCS - 1105-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1
Start By:
a. Remove cylinder head.
Note: Refer to Specification UENR0995 "Engine Design" for non-specified engine Torque
Values.
1. Clean the bottom mating surface of the cylinder head. Check the depth of the valves below
the face of the cylinder head before the valve springs are removed. Refer to Specifications,
"Cylinder Head Valves" for the correct dimensions.
2. Place a temporary identification mark on the heads of the valves in order to identify the
correct position.
3. Use a suitable lifting device to position the cylinder head with the valve springs upward.
The weight of the cylinder head is approximately 23 kg (51 lb).
1/3
246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...