This service repair manual provides instructions for removing and installing various engine components on a 262D Skid Steer Loader with a C3.3B engine, including the engine oil pump, water pump, water temperature regulator, flywheel, crankshaft rear seal and wear sleeve. The procedures provide detailed steps and illustrations for each component removal and installation, noting any required tools and torque specifications. Safety and maintenance tips are also provided throughout.
Caterpillar cat 262 d skid steer loader (prefix kts) service repair manual (k...fjjkekfksemmm
This document provides instructions for removing and installing various engine components on a 262D Skid Steer Loader, including:
- Engine oil pump removal and installation procedures involving removing covers and rotors.
- Water pump removal by taking off bolts and pulley, and installing a new gasket.
- Removing the water temperature regulator by disconnecting hoses and bolts.
- Flywheel removal using lifting tools after removing bolts, and inspecting components.
- Crankshaft rear seal and wear sleeve removal after positioning the engine at top dead center.
Caterpillar cat 262 d skid steer loader (prefix kts) service repair manual (k...fusjejedrfjskekem
This document provides instructions for removing and installing various engine components on a 262D Skid Steer Loader with a C3.3B engine, including:
- Removing and installing the engine oil pump
- Removing and installing the water pump
- Removing and installing the water temperature regulator
- Removing and installing the flywheel
- Removing the crankshaft rear seal, wear sleeve, and crankshaft gear
- Installing the crankshaft rear seal, wear sleeve, and crankshaft gear
The instructions provide detailed steps for each procedure, including illustrations of the components. Safety notices are included to handle fluids properly and keep parts clean from contaminants.
Caterpillar cat 262 d skid steer loader (prefix kts) service repair manual (k...fjsjkseikdmme
This document provides instructions for removing and installing various engine components on a 262D Skid Steer Loader, including:
- Engine oil pump removal and installation procedures involving removing covers and rotors.
- Water pump removal by taking off bolts and pulley, and installing a new gasket.
- Removing the water temperature regulator by disconnecting hoses and bolts.
- Flywheel removal using lifting tools after removing bolts, and inspecting components. Proper installation also covered.
- Crankshaft rear seal and wear sleeve removal after placing the engine at top dead center.
Caterpillar cat 262 d skid steer loader (prefix kts) service repair manual (k...fujsjfkkskemme
This document provides instructions for removing and installing various engine components on a 262D Skid Steer Loader with a C3.3B engine, including:
- Removing and installing the engine oil pump
- Removing and installing the water pump
- Removing and installing the water temperature regulator
- Removing and installing the flywheel
- Removing the crankshaft rear seal, wear sleeve, and crankshaft gear
- Installing the crankshaft rear seal, wear sleeve, and crankshaft gear
The document provides detailed step-by-step instructions with illustrations for each procedure, and notes on cleaning, inspection, and replacement of parts. Safety notices are also included.
This document provides instructions for removing and installing various engine components on a 262D Skid Steer Loader including the engine oil pump, water pump, water temperature regulator, flywheel, crankshaft rear seal and wear sleeve, and crankshaft gear. The procedures describe removing components, inspecting parts for wear or damage, cleaning components, and installing components in the reverse order of removal while applying specified torques. Safety notices are included to contain fluids and warn of heated parts.
This document provides instructions for removing and installing various engine components on a 262D Skid Steer Loader including the engine oil pump, water pump, water temperature regulator, flywheel, crankshaft rear seal and wear sleeve, and crankshaft gear. The procedures describe removing components, inspecting parts for wear or damage, cleaning components, and installing components in the reverse order of removal while applying the correct torque specifications. Safety notices are provided to contain fluids, wear protective equipment, and keep parts clean from contaminants.
This document provides instructions for removing and installing various engine components on a 262D Skid Steer Loader including the engine oil pump, water pump, water temperature regulator, flywheel, crankshaft rear seal and wear sleeve, and crankshaft gear. The procedures describe removing components, inspecting parts for wear or damage, cleaning components, and installing components in the reverse order of removal while applying the correct torque to fasteners. Safety notices are provided to contain fluids and wear protective equipment when handling heated parts.
Caterpillar cat 262 d skid steer loader (prefix aj7) service repair manual (a...fujsjfkkskemme
This document provides instructions for removing and installing various engine components on a 262D Skid Steer Loader with a C3.3B engine, including:
1. Removing and installing the flywheel, which involves using guide tools and lifting equipment due to its weight of approximately 30 kg.
2. Removing the crankshaft rear seal and wear sleeve, which requires placing the engine at top dead center and using screwdrivers and chisels.
3. Installing the crankshaft rear seal and wear sleeve, which involves using a driver tool and press.
4. Removing and installing the flywheel housing, which requires guide tools, link brackets, and lifting equipment due to its
Caterpillar cat 262 d skid steer loader (prefix kts) service repair manual (k...fjjkekfksemmm
This document provides instructions for removing and installing various engine components on a 262D Skid Steer Loader, including:
- Engine oil pump removal and installation procedures involving removing covers and rotors.
- Water pump removal by taking off bolts and pulley, and installing a new gasket.
- Removing the water temperature regulator by disconnecting hoses and bolts.
- Flywheel removal using lifting tools after removing bolts, and inspecting components.
- Crankshaft rear seal and wear sleeve removal after positioning the engine at top dead center.
Caterpillar cat 262 d skid steer loader (prefix kts) service repair manual (k...fusjejedrfjskekem
This document provides instructions for removing and installing various engine components on a 262D Skid Steer Loader with a C3.3B engine, including:
- Removing and installing the engine oil pump
- Removing and installing the water pump
- Removing and installing the water temperature regulator
- Removing and installing the flywheel
- Removing the crankshaft rear seal, wear sleeve, and crankshaft gear
- Installing the crankshaft rear seal, wear sleeve, and crankshaft gear
The instructions provide detailed steps for each procedure, including illustrations of the components. Safety notices are included to handle fluids properly and keep parts clean from contaminants.
Caterpillar cat 262 d skid steer loader (prefix kts) service repair manual (k...fjsjkseikdmme
This document provides instructions for removing and installing various engine components on a 262D Skid Steer Loader, including:
- Engine oil pump removal and installation procedures involving removing covers and rotors.
- Water pump removal by taking off bolts and pulley, and installing a new gasket.
- Removing the water temperature regulator by disconnecting hoses and bolts.
- Flywheel removal using lifting tools after removing bolts, and inspecting components. Proper installation also covered.
- Crankshaft rear seal and wear sleeve removal after placing the engine at top dead center.
Caterpillar cat 262 d skid steer loader (prefix kts) service repair manual (k...fujsjfkkskemme
This document provides instructions for removing and installing various engine components on a 262D Skid Steer Loader with a C3.3B engine, including:
- Removing and installing the engine oil pump
- Removing and installing the water pump
- Removing and installing the water temperature regulator
- Removing and installing the flywheel
- Removing the crankshaft rear seal, wear sleeve, and crankshaft gear
- Installing the crankshaft rear seal, wear sleeve, and crankshaft gear
The document provides detailed step-by-step instructions with illustrations for each procedure, and notes on cleaning, inspection, and replacement of parts. Safety notices are also included.
This document provides instructions for removing and installing various engine components on a 262D Skid Steer Loader including the engine oil pump, water pump, water temperature regulator, flywheel, crankshaft rear seal and wear sleeve, and crankshaft gear. The procedures describe removing components, inspecting parts for wear or damage, cleaning components, and installing components in the reverse order of removal while applying specified torques. Safety notices are included to contain fluids and warn of heated parts.
This document provides instructions for removing and installing various engine components on a 262D Skid Steer Loader including the engine oil pump, water pump, water temperature regulator, flywheel, crankshaft rear seal and wear sleeve, and crankshaft gear. The procedures describe removing components, inspecting parts for wear or damage, cleaning components, and installing components in the reverse order of removal while applying the correct torque specifications. Safety notices are provided to contain fluids, wear protective equipment, and keep parts clean from contaminants.
This document provides instructions for removing and installing various engine components on a 262D Skid Steer Loader including the engine oil pump, water pump, water temperature regulator, flywheel, crankshaft rear seal and wear sleeve, and crankshaft gear. The procedures describe removing components, inspecting parts for wear or damage, cleaning components, and installing components in the reverse order of removal while applying the correct torque to fasteners. Safety notices are provided to contain fluids and wear protective equipment when handling heated parts.
Caterpillar cat 262 d skid steer loader (prefix aj7) service repair manual (a...fujsjfkkskemme
This document provides instructions for removing and installing various engine components on a 262D Skid Steer Loader with a C3.3B engine, including:
1. Removing and installing the flywheel, which involves using guide tools and lifting equipment due to its weight of approximately 30 kg.
2. Removing the crankshaft rear seal and wear sleeve, which requires placing the engine at top dead center and using screwdrivers and chisels.
3. Installing the crankshaft rear seal and wear sleeve, which involves using a driver tool and press.
4. Removing and installing the flywheel housing, which requires guide tools, link brackets, and lifting equipment due to its
Caterpillar cat 262 d skid steer loader (prefix aj7) service repair manual (a...fjsjkseikdmme
This document provides instructions for removing and installing various engine components on a 262D Skid Steer Loader with a C3.3B engine, including:
1. Removing and installing the flywheel, which involves using guide studs and link brackets to lift the flywheel and torquing bolts to a specified range.
2. Removing and installing the crankshaft rear seal and wear sleeve, which involves using a driver and press to install the sleeve and seal.
3. Removing and installing the flywheel housing, which involves using guide studs and link brackets to lift the housing, applying liquid gasket, and torquing bolts to a specified range.
4. Removing
Caterpillar cat 262 d skid steer loader (prefix aj7) service repair manual (a...fjjkekfksemmm
This document provides instructions for servicing components of a 262D Skid Steer Loader engine. It describes removing and installing the flywheel, crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, and crankshaft front seal. The procedures include using various tools to remove bolts and seals, inspecting parts for wear, applying sealant or oil, and tightening bolts to the specified torque values. Safety notices are included to keep parts clean and contain fluids during repair.
Caterpillar cat 262 d skid steer loader (prefix aj7) service repair manual (a...fusjejedrfjskekem
This document provides instructions for removing and installing various engine components on a 262D Skid Steer Loader with a C3.3B engine, including:
1. Removing and installing the flywheel, which involves using guide studs and link brackets to lift the flywheel and torquing bolts to a specified range.
2. Removing and installing the crankshaft rear seal and wear sleeve, which involves using a driver and press to install the sleeve and seal.
3. Removing and installing the flywheel housing, which involves using guide studs and link brackets to lift the housing, applying liquid gasket, and torquing bolts to a specified range.
4. Removing
This document provides instructions for servicing components related to the crankshaft on a Caterpillar C3.3B engine, including:
1. Removing and installing the flywheel, which involves using guide studs and lifting equipment due to its weight of approximately 30 kg.
2. Removing the crankshaft rear seal, crankshaft gear, and wear sleeve, and inspecting these components for wear and damage.
3. Installing the crankshaft rear seal, crankshaft gear, and wear sleeve, which requires aligning gears and using a press and driver tool.
4. Removing and installing the flywheel housing, which connects the upper and lower
This document provides instructions for servicing components related to the crankshaft on a Caterpillar C3.3B engine, including:
1. Removing and installing the flywheel, which involves using guide studs and lifting equipment due to its weight of approximately 30 kg.
2. Removing the crankshaft rear seal, crankshaft gear, and wear sleeve, and inspecting these components for wear and damage.
3. Installing the crankshaft rear seal, crankshaft gear, and wear sleeve, which requires aligning gears and using a press and driver tool.
4. Removing and installing the flywheel housing, which connects the upper and lower
This document provides instructions for removing and installing various engine components on a 262D Skid Steer Loader with a C3.3B engine, including:
1. Removing the flywheel by using guide studs and link brackets to lift it off after removing bolts.
2. Removing the crankshaft rear seal and wear sleeve by using screwdrivers and chisels after placing the engine at top dead center.
3. Installing the crankshaft rear seal and wear sleeve using a driver and press to insert the wear sleeve before installing the seal.
This document provides instructions for servicing components related to the crankshaft on a Caterpillar C3.3B engine, including:
1. Removing and installing the flywheel, which involves using guide studs and lifting equipment due to its weight of approximately 30 kg.
2. Removing the crankshaft rear seal, crankshaft gear, and wear sleeve, and inspecting these components for wear and damage.
3. Installing the crankshaft rear seal, crankshaft gear, and wear sleeve, which requires aligning gears and using a press and driver tool.
4. Removing and installing the flywheel housing, which connects the upper and lower
This document provides instructions for servicing components related to the crankshaft on a Caterpillar C3.3B engine, including:
1. Removing and installing the flywheel, which involves using guide studs and lifting equipment due to its weight of approximately 30 kg.
2. Removing the crankshaft rear seal, crankshaft gear, and wear sleeve, and inspecting these components for wear and damage.
3. Installing the crankshaft rear seal, crankshaft gear, and wear sleeve, which requires aligning gears and using a press and driver tool.
4. Removing and installing the flywheel housing, which mounts to the cylinder block
This document provides instructions for servicing components related to the crankshaft on a Caterpillar C3.3B engine, including:
1. Removing and installing the flywheel, which involves using guide studs and lifting equipment due to its weight of approximately 30 kg.
2. Removing the crankshaft rear seal and wear sleeve, which protects the crankshaft, as well as removing and installing the crankshaft gear.
3. Removing and installing the flywheel housing, which houses the crankshaft and requires special tools due to its weight of approximately 25 kg.
4. Procedures for removing and installing the crankshaft pulley and
This document provides instructions for removing and installing various engine components on a 262D Skid Steer Loader with a C3.3B engine, including:
1. Removing the flywheel by using guide studs and link brackets to lift it off after removing bolts.
2. Removing the crankshaft rear seal and wear sleeve using screwdrivers and chisels.
3. Installing the crankshaft rear seal and wear sleeve using driver tools and presses to insert the new components.
4. Removing the flywheel housing by first removing the flywheel and rear seal, then taking out bolts and lifting the housing off using guide studs and link brackets.
This document provides instructions for servicing components related to the crankshaft on a Caterpillar C3.3B engine, including:
1. Removing and installing the flywheel, which involves using guide studs and lifting equipment due to its weight of approximately 30 kg.
2. Removing the crankshaft rear seal, crankshaft gear, and wear sleeve, and inspecting these components for wear and damage.
3. Installing the crankshaft rear seal, crankshaft gear, and wear sleeve, which requires aligning gears and using a press and driver tool.
4. Removing and installing the flywheel housing, which mounts to the cylinder block
This document provides instructions for servicing components related to the crankshaft on a Caterpillar C3.3B engine, including:
1. Removing and installing the flywheel, which involves using guide studs and lifting equipment due to its weight of approximately 30 kg.
2. Removing the crankshaft rear seal, crankshaft gear, and wear sleeve, and inspecting these components for wear and damage.
3. Installing the crankshaft rear seal, crankshaft gear, and wear sleeve, which requires aligning gears and using a press and driver tool.
4. Removing and installing the flywheel housing, which mounts to the cylinder block
This document provides instructions for servicing components related to the crankshaft on a Caterpillar C3.3B engine, including:
1. Removing and installing the flywheel, which involves using guide studs and lifting equipment due to its weight of approximately 30 kg.
2. Removing the crankshaft rear seal, crankshaft gear, and wear sleeve, and inspecting these components for wear and damage.
3. Installing the crankshaft rear seal, crankshaft gear, and wear sleeve, which requires aligning gears and using a press and driver tool.
4. Removing and installing the flywheel housing, which connects the upper and lower
This document provides instructions for servicing components related to the crankshaft on a Caterpillar C3.3B engine, including:
1. Removing and installing the flywheel, which involves using guide studs and lifting equipment due to its weight of approximately 30 kg.
2. Removing the crankshaft rear seal and wear sleeve, which protects the crankshaft, as well as removing and installing the crankshaft gear.
3. Removing and installing the flywheel housing, which houses the crankshaft and requires special tools due to its weight of approximately 25 kg.
4. Procedures for removing and installing the crankshaft pulley and
This document provides instructions for removing and installing various engine components on a 262D Skid Steer Loader with a C3.3B engine, including:
1. Removing the flywheel by using guide studs and link brackets to lift it off after removing bolts.
2. Removing the crankshaft rear seal and wear sleeve using screwdrivers and chisels.
3. Removing the flywheel housing by first removing the flywheel, rear seal, and bolts, then lifting it off using guide studs and link brackets.
4. Procedures for installing the removed components are also provided in reverse order.
Caterpillar Cat 160M Motor Grader (Prefix D9T) Service Repair Manual (D9T0000...f7useijdkdmdm
This document provides disassembly instructions for the transmission of a 160M Motor Grader. It lists over 50 steps to fully disassemble the transmission along with required tools. These steps include removing components like the transmission housing, clutch assemblies, gears, seals, pistons, and sensors. Diagrams are provided to illustrate where each component is located and how to remove it. Precautions are mentioned regarding fluid containment and releasing spring forces when disassembling parts.
Caterpillar Cat 307D Mini Hydraulic Excavator (Prefix DSG) Service Repair Man...f7useijdkdmdm
The document provides instructions for removing and installing various engine components on a 307D Mini Hydraulic Excavator including the fuel filter and water separator base, engine oil filter and oil filter base, and air cleaner. The procedures describe draining fluids, disconnecting hoses, removing bolts and filters, cleaning parts, applying oil, and reinstalling components in the reverse order of removal. Safety precautions are provided to prevent injury and contain fluids.
Caterpillar Cat 307E2 Mini Hydraulic Excavator (Prefix KC9) Service Repair Ma...f7useijdkdmdm
The document provides instructions for removing and installing various components of a 307E2 Mini Hydraulic Excavator engine, including the fuel manifold, fuel injection lines, fuel injection pump, electronic unit injector, turbocharger, and exhaust gas recirculation valve. Safety precautions are provided, such as wearing protective equipment when draining fluids and precautions for high pressure fuel lines. The procedures note removing retaining bolts, clamps, and hoses and reinstalling components in the reverse order.
The document provides instructions for removing and installing the valve mechanism cover on a Caterpillar 3054 diesel engine. The removal procedure involves loosening the breather hose clamp, removing three nuts and washers to detach the valve cover, and removing seals from the valve cover and oil filler cap. The installation procedure involves replacing any seals and gaskets, placing the valve cover into position, and securing it with three nuts, washers, and tightening the breather hose clamp. Safety notices are provided to keep parts clean and contain fluids.
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar C4.4 engine. To remove the flywheel, two guide bolts must be inserted and bolts removed using a lifting device due to the flywheel's weight of approximately 71 kg. To install the flywheel, a lifting device is also used to position the flywheel onto the guide bolts before installing and tightening the bolts. Removing the crankshaft rear seal involves using a socket to remove torx screws, while installing the new seal requires aligning its locators with the cylinder block holes and tightening screws in a specific sequence.
This document provides instructions for installing an engine in a 420F2 backhoe loader. It outlines 17 steps for installing the engine, connecting various components like the transmission, alternator, and fuel system. Tools required are listed. Photos illustrate each step, and safety notices are included.
This document provides instructions for removing and installing an engine from a 420F2 backhoe loader. It outlines 19 steps to remove the engine, which includes draining fluids, disconnecting wiring harnesses, removing mounting hardware, and lifting the engine out. It then describes 19 steps to install the engine in reverse order, including lowering the engine into place, reconnecting wiring, refilling fluids, and reinstalling ancillary components. The purpose is to provide technicians with a procedure to safely remove and reinstall the engine.
More Related Content
Similar to Caterpillar Cat 262D Skid Steer Loader (Prefix KTS) Service Repair Manual (KTS00001 and up).pdf
Caterpillar cat 262 d skid steer loader (prefix aj7) service repair manual (a...fjsjkseikdmme
This document provides instructions for removing and installing various engine components on a 262D Skid Steer Loader with a C3.3B engine, including:
1. Removing and installing the flywheel, which involves using guide studs and link brackets to lift the flywheel and torquing bolts to a specified range.
2. Removing and installing the crankshaft rear seal and wear sleeve, which involves using a driver and press to install the sleeve and seal.
3. Removing and installing the flywheel housing, which involves using guide studs and link brackets to lift the housing, applying liquid gasket, and torquing bolts to a specified range.
4. Removing
Caterpillar cat 262 d skid steer loader (prefix aj7) service repair manual (a...fjjkekfksemmm
This document provides instructions for servicing components of a 262D Skid Steer Loader engine. It describes removing and installing the flywheel, crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, and crankshaft front seal. The procedures include using various tools to remove bolts and seals, inspecting parts for wear, applying sealant or oil, and tightening bolts to the specified torque values. Safety notices are included to keep parts clean and contain fluids during repair.
Caterpillar cat 262 d skid steer loader (prefix aj7) service repair manual (a...fusjejedrfjskekem
This document provides instructions for removing and installing various engine components on a 262D Skid Steer Loader with a C3.3B engine, including:
1. Removing and installing the flywheel, which involves using guide studs and link brackets to lift the flywheel and torquing bolts to a specified range.
2. Removing and installing the crankshaft rear seal and wear sleeve, which involves using a driver and press to install the sleeve and seal.
3. Removing and installing the flywheel housing, which involves using guide studs and link brackets to lift the housing, applying liquid gasket, and torquing bolts to a specified range.
4. Removing
This document provides instructions for servicing components related to the crankshaft on a Caterpillar C3.3B engine, including:
1. Removing and installing the flywheel, which involves using guide studs and lifting equipment due to its weight of approximately 30 kg.
2. Removing the crankshaft rear seal, crankshaft gear, and wear sleeve, and inspecting these components for wear and damage.
3. Installing the crankshaft rear seal, crankshaft gear, and wear sleeve, which requires aligning gears and using a press and driver tool.
4. Removing and installing the flywheel housing, which connects the upper and lower
This document provides instructions for servicing components related to the crankshaft on a Caterpillar C3.3B engine, including:
1. Removing and installing the flywheel, which involves using guide studs and lifting equipment due to its weight of approximately 30 kg.
2. Removing the crankshaft rear seal, crankshaft gear, and wear sleeve, and inspecting these components for wear and damage.
3. Installing the crankshaft rear seal, crankshaft gear, and wear sleeve, which requires aligning gears and using a press and driver tool.
4. Removing and installing the flywheel housing, which connects the upper and lower
This document provides instructions for removing and installing various engine components on a 262D Skid Steer Loader with a C3.3B engine, including:
1. Removing the flywheel by using guide studs and link brackets to lift it off after removing bolts.
2. Removing the crankshaft rear seal and wear sleeve by using screwdrivers and chisels after placing the engine at top dead center.
3. Installing the crankshaft rear seal and wear sleeve using a driver and press to insert the wear sleeve before installing the seal.
This document provides instructions for servicing components related to the crankshaft on a Caterpillar C3.3B engine, including:
1. Removing and installing the flywheel, which involves using guide studs and lifting equipment due to its weight of approximately 30 kg.
2. Removing the crankshaft rear seal, crankshaft gear, and wear sleeve, and inspecting these components for wear and damage.
3. Installing the crankshaft rear seal, crankshaft gear, and wear sleeve, which requires aligning gears and using a press and driver tool.
4. Removing and installing the flywheel housing, which connects the upper and lower
This document provides instructions for servicing components related to the crankshaft on a Caterpillar C3.3B engine, including:
1. Removing and installing the flywheel, which involves using guide studs and lifting equipment due to its weight of approximately 30 kg.
2. Removing the crankshaft rear seal, crankshaft gear, and wear sleeve, and inspecting these components for wear and damage.
3. Installing the crankshaft rear seal, crankshaft gear, and wear sleeve, which requires aligning gears and using a press and driver tool.
4. Removing and installing the flywheel housing, which mounts to the cylinder block
This document provides instructions for servicing components related to the crankshaft on a Caterpillar C3.3B engine, including:
1. Removing and installing the flywheel, which involves using guide studs and lifting equipment due to its weight of approximately 30 kg.
2. Removing the crankshaft rear seal and wear sleeve, which protects the crankshaft, as well as removing and installing the crankshaft gear.
3. Removing and installing the flywheel housing, which houses the crankshaft and requires special tools due to its weight of approximately 25 kg.
4. Procedures for removing and installing the crankshaft pulley and
This document provides instructions for removing and installing various engine components on a 262D Skid Steer Loader with a C3.3B engine, including:
1. Removing the flywheel by using guide studs and link brackets to lift it off after removing bolts.
2. Removing the crankshaft rear seal and wear sleeve using screwdrivers and chisels.
3. Installing the crankshaft rear seal and wear sleeve using driver tools and presses to insert the new components.
4. Removing the flywheel housing by first removing the flywheel and rear seal, then taking out bolts and lifting the housing off using guide studs and link brackets.
This document provides instructions for servicing components related to the crankshaft on a Caterpillar C3.3B engine, including:
1. Removing and installing the flywheel, which involves using guide studs and lifting equipment due to its weight of approximately 30 kg.
2. Removing the crankshaft rear seal, crankshaft gear, and wear sleeve, and inspecting these components for wear and damage.
3. Installing the crankshaft rear seal, crankshaft gear, and wear sleeve, which requires aligning gears and using a press and driver tool.
4. Removing and installing the flywheel housing, which mounts to the cylinder block
This document provides instructions for servicing components related to the crankshaft on a Caterpillar C3.3B engine, including:
1. Removing and installing the flywheel, which involves using guide studs and lifting equipment due to its weight of approximately 30 kg.
2. Removing the crankshaft rear seal, crankshaft gear, and wear sleeve, and inspecting these components for wear and damage.
3. Installing the crankshaft rear seal, crankshaft gear, and wear sleeve, which requires aligning gears and using a press and driver tool.
4. Removing and installing the flywheel housing, which mounts to the cylinder block
This document provides instructions for servicing components related to the crankshaft on a Caterpillar C3.3B engine, including:
1. Removing and installing the flywheel, which involves using guide studs and lifting equipment due to its weight of approximately 30 kg.
2. Removing the crankshaft rear seal, crankshaft gear, and wear sleeve, and inspecting these components for wear and damage.
3. Installing the crankshaft rear seal, crankshaft gear, and wear sleeve, which requires aligning gears and using a press and driver tool.
4. Removing and installing the flywheel housing, which connects the upper and lower
This document provides instructions for servicing components related to the crankshaft on a Caterpillar C3.3B engine, including:
1. Removing and installing the flywheel, which involves using guide studs and lifting equipment due to its weight of approximately 30 kg.
2. Removing the crankshaft rear seal and wear sleeve, which protects the crankshaft, as well as removing and installing the crankshaft gear.
3. Removing and installing the flywheel housing, which houses the crankshaft and requires special tools due to its weight of approximately 25 kg.
4. Procedures for removing and installing the crankshaft pulley and
This document provides instructions for removing and installing various engine components on a 262D Skid Steer Loader with a C3.3B engine, including:
1. Removing the flywheel by using guide studs and link brackets to lift it off after removing bolts.
2. Removing the crankshaft rear seal and wear sleeve using screwdrivers and chisels.
3. Removing the flywheel housing by first removing the flywheel, rear seal, and bolts, then lifting it off using guide studs and link brackets.
4. Procedures for installing the removed components are also provided in reverse order.
Similar to Caterpillar Cat 262D Skid Steer Loader (Prefix KTS) Service Repair Manual (KTS00001 and up).pdf (15)
Caterpillar Cat 160M Motor Grader (Prefix D9T) Service Repair Manual (D9T0000...f7useijdkdmdm
This document provides disassembly instructions for the transmission of a 160M Motor Grader. It lists over 50 steps to fully disassemble the transmission along with required tools. These steps include removing components like the transmission housing, clutch assemblies, gears, seals, pistons, and sensors. Diagrams are provided to illustrate where each component is located and how to remove it. Precautions are mentioned regarding fluid containment and releasing spring forces when disassembling parts.
Caterpillar Cat 307D Mini Hydraulic Excavator (Prefix DSG) Service Repair Man...f7useijdkdmdm
The document provides instructions for removing and installing various engine components on a 307D Mini Hydraulic Excavator including the fuel filter and water separator base, engine oil filter and oil filter base, and air cleaner. The procedures describe draining fluids, disconnecting hoses, removing bolts and filters, cleaning parts, applying oil, and reinstalling components in the reverse order of removal. Safety precautions are provided to prevent injury and contain fluids.
Caterpillar Cat 307E2 Mini Hydraulic Excavator (Prefix KC9) Service Repair Ma...f7useijdkdmdm
The document provides instructions for removing and installing various components of a 307E2 Mini Hydraulic Excavator engine, including the fuel manifold, fuel injection lines, fuel injection pump, electronic unit injector, turbocharger, and exhaust gas recirculation valve. Safety precautions are provided, such as wearing protective equipment when draining fluids and precautions for high pressure fuel lines. The procedures note removing retaining bolts, clamps, and hoses and reinstalling components in the reverse order.
The document provides instructions for removing and installing the valve mechanism cover on a Caterpillar 3054 diesel engine. The removal procedure involves loosening the breather hose clamp, removing three nuts and washers to detach the valve cover, and removing seals from the valve cover and oil filler cap. The installation procedure involves replacing any seals and gaskets, placing the valve cover into position, and securing it with three nuts, washers, and tightening the breather hose clamp. Safety notices are provided to keep parts clean and contain fluids.
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar C4.4 engine. To remove the flywheel, two guide bolts must be inserted and bolts removed using a lifting device due to the flywheel's weight of approximately 71 kg. To install the flywheel, a lifting device is also used to position the flywheel onto the guide bolts before installing and tightening the bolts. Removing the crankshaft rear seal involves using a socket to remove torx screws, while installing the new seal requires aligning its locators with the cylinder block holes and tightening screws in a specific sequence.
This document provides instructions for installing an engine in a 420F2 backhoe loader. It outlines 17 steps for installing the engine, connecting various components like the transmission, alternator, and fuel system. Tools required are listed. Photos illustrate each step, and safety notices are included.
This document provides instructions for removing and installing an engine from a 420F2 backhoe loader. It outlines 19 steps to remove the engine, which includes draining fluids, disconnecting wiring harnesses, removing mounting hardware, and lifting the engine out. It then describes 19 steps to install the engine in reverse order, including lowering the engine into place, reconnecting wiring, refilling fluids, and reinstalling ancillary components. The purpose is to provide technicians with a procedure to safely remove and reinstall the engine.
This document provides instructions for removing and installing the flywheel, crankshaft rear seal, and crankshaft wear sleeve on a Caterpillar 3054C engine. The removal procedure for the flywheel involves using guide bolts and a link bracket to support the flywheel weight before removing all setscrews. The crankshaft rear seal housing assembly must be replaced as a unit if removed. A plastic sleeve is used to protect the crankshaft rear seal during installation. A puller and spacer are used to remove the crankshaft wear sleeve, which is used to reclaim a worn crankshaft seal surface.
This document provides instructions for installing an engine on a 416F2 Backhoe Loader. It describes attaching lifting equipment to the engine, aligning and bolting the bell housing and flywheel, installing engine mounts and accessories like the alternator, air conditioning compressor and fuel system components. The 17 step procedure includes attaching hoses, wiring harnesses and filling fluids before installing remaining panels and covers.
This document provides instructions for removing and installing various engine components on a Caterpillar 3054C engine, including:
- Lifters can be removed and installed using a telescoping magnet. Proper identification and lubrication is required.
- Camshaft removal requires removing the rocker shaft assembly, pushrods, and front housing first. The camshaft is then carefully removed and installed.
- Camshaft bearings are removed and installed using a special tool, ensuring the oil hole is properly aligned during installation.
- Piston cooling jets are accessed by first removing the engine oil pan and then removing a setscrew to access the assembly.
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader. It describes removing the flywheel by taking out bolts and using guide bolts and lifting equipment due to the flywheel's weight of approximately 155 pounds. For installing the flywheel, the instructions specify cleaning components, heating the ring gear, lifting the flywheel into place, and tightening bolts to the specified torque. Removing the crankshaft rear seal involves using a socket to remove screws, while installing requires aligning and pressing the new seal onto the crankshaft flange and torquing screws to the specified value.
The document provides instructions for installing a flywheel and crankshaft rear seal on a Caterpillar 3054C engine. It describes cleaning and preparing the components, heating the ring gear to install it on the flywheel, installing guide bolts and lifting brackets to position the flywheel, and tightening the bolts to specification. It also explains that the crankshaft rear seal is replaced as an assembly, including inserting a plastic sleeve to protect the seal during installation and tightening setscrews to secure the assembly.
1. The document provides assembly instructions for the transmission of a 416D Backhoe Loader.
2. It describes assembling the transmission in major components and then assembling the components together.
3. Cleanliness is important during assembly and all parts should be cleaned and inspected before assembly, applying a light film of transmission oil to components.
This document provides instructions for removing and installing the flywheel housing on a Caterpillar 3054 engine. The removal procedure involves removing mounting bolts from the top and bottom of the housing and using lifting tools to detach the housing from the cylinder block. The installation procedure specifies cleaning parts, placing the housing in position, and tightening mounting bolts to secure the housing. Tools required include link brackets for lifting.
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It includes removal and installation procedures with lists of required tools and illustrations showing the step-by-step processes. The instructions cover both engines with a 14 bolt housing assembly and engines with a 10 bolt housing assembly.
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to remove the flywheel using a lifting device and remove the bolts and bearing housing. To install the flywheel, it describes heating the flywheel ring gear, positioning the flywheel and tightening the bolts. It also provides instructions for removing and installing the crankshaft rear seal, which involves removing housing bolts and installing the seal using a press and installer tool.
This document provides instructions for removing and installing a flywheel housing on a 416C Backhoe Loader with a 3054 engine. It describes using lifting brackets and removing mounting bolts to detach the housing. Cleaning surfaces and replacing seals is emphasized. Diagrams illustrate the housing and bolt locations. Proper safety procedures and required tools are also outlined.
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and multi-step processes for both removal and installation. Removal of the flywheel requires using a lifting device to remove bolts and separate the flywheel. Installation requires heating, positioning, and torquing components in the correct order.
This document provides instructions for removing and installing a crankshaft rear seal on a Caterpillar 3054 engine. It describes the necessary tools and parts, safety precautions, and step-by-step procedures for both removing the old seal and installing the new one. The procedures are separated into sections for engines with a 14-bolt housing assembly versus a 10-bolt housing assembly. Precise instructions are given for lubricating parts, inserting the seal, aligning components, and tightening bolts to the specified torque.
This document provides instructions for removing the crankshaft front seal from a Caterpillar 3054 engine. The steps are:
1. Use a drill bit to drill out the spot welds securing the seal retainer.
2. Remove the retainer, crankshaft front seal, and gasket from the front cover.
3. Inspect the front cover dowels and replace if needed before installing the new seal.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 262D SKID STEER LOADER KTS
Configuration: 262D Skid Steer Loader KTS00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
C2.6 and C3.3B Engines for Caterpillar Built Machines
Media Number -UENR0137-11 Publication Date -01/08/2015 Date Updated -12/07/2018
i05242520
Engine Oil Pump - Remove and Install
SMCS - 1304-010
Removal Procedure
Start By:
a. Remove the front housing.
Note: Refer to Specification UENR0995 "Engine Design" for non-specified engine Torque
Values.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
1/4
262D Skid Steer Loader KTS00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g02788686
1. Remove screws (2) and cover (1).
Illustration 2 g02788689
2. Remove inner rotor (4) from outer rotor (3).
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 129-1967 White Grease 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/4
262D Skid Steer Loader KTS00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. NOTICE
If any part of the engine oil pump is worn or damaged, the complete
assembly of the engine oil pump must be replaced.
1. Ensure that all components of the engine oil pump are clean and free from wear and
damage.
Illustration 3 g02788689
2. Position outer rotor (3) into the pump body. Check the clearance between outer rotor (3) and
the pump body.
3. Install inner rotor (4) into outer rotor (3). Check the clearance between the lobes of outer
rotor (3) and inner rotor (4).
Illustration 4 g02788686
4. Position a strip of Plastigage onto the outer rotor face with Tooling (A). Position cover (1)
and install screws (2) and torque. Remove cover (1) and check clearance between the rotor
and cover (1).
5. Position cover (1) and install screws (2). Tighten screws (2) to a torque of 8 to 9 N·m
(70 to 83 lb in).
3/4
262D Skid Steer Loader KTS00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. End By:
a. Install the front housing.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Nov 17 23:38:42 UTC+0800 2019
4/4
262D Skid Steer Loader KTS00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 262D SKID STEER LOADER KTS
Configuration: 262D Skid Steer Loader KTS00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
C2.6 and C3.3B Engines for Caterpillar Built Machines
Media Number -UENR0137-11 Publication Date -01/08/2015 Date Updated -12/07/2018
i05242522
Water Pump - Remove and Install
SMCS - 1361-011; 1361-012
Removal Procedure
Start By:
a. Remove the v-belts.
Note: Refer to Specification UENR0995 "Engine Design" for non-specified engine Torque
Values.
1. Refer to Operation and Maintenance Manual, "Coolant - Change" for the proper draining
and filling procedures.
Illustration 1 g02794283
2. Remove bolts (2) and remove pulley (1).
1/2
262D Skid Steer Loader KTS00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 2 g02794286
3. Remove bolts (4).
4. Remove water pump (3) and discard the gasket. Install a new gasket upon installation.
Installation Procedure
1. Install water pump (3) in the reverse order of removal.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Nov 17 23:39:41 UTC+0800 2019
2/2
262D Skid Steer Loader KTS00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Dispose of all fluids according to local regulations and mandates.
1. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the
correct draining procedure.
Note: Coolant only needs drained to below the water temperature regulator.
Illustration 1 g02794379
2. Disconnect hose assembly (1).
3. Remove bolts (2) from the water temperature regulator housing . Remove water temperature
regulator elbow (3).
Illustration 2 g02794381
3/4
262D Skid Steer Loader KTS00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 3 g02794385
4. Remove gasket (5) and remove water temperature regulator (4) from the water temperature
regulator housing.
Note: Note the orientation of the water temperature regulator elbow.
Installation Procedure
1. Install water temperature regulator (4) in the reverse order of removal.
a. Check the water temperature regulator for correct operation. Refer to System
Operation, Testing and Adjusting, "Water Temperature Regulator - Test" for the
correct procedure to test the water temperature regulator. If any components of the
water temperature regulator housing are worn or damaged, the complete assembly
must be replaced.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Nov 17 23:40:41 UTC+0800 2019
4/4
262D Skid Steer Loader KTS00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g02794543
1. Remove two bolts (2) from flywheel (1).
Illustration 2 g02798921
2. Install Tooling (A) into the crankshaft.
3. Install Tooling (B) and a suitable lifting device on flywheel (1). The weight of flywheel (1)
is approximately 30 kg (66 lb).
4. Remove remaining bolts (2).
5. Remove flywheel (1) from the cylinder block.
3/6
262D Skid Steer Loader KTS00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 3 g02798923
6. Inspect flywheel (1) and the ring gear (3) for wear and damage. Replace any worn
components or damaged components.
7. If necessary, remove the flywheel ring gear (3), follow Step 7.a through Step 7.b.
a. Place the flywheel assembly on a suitable support.
b. Use a hammer and a punch in order to remove ring gear (3) from flywheel (1). If
necessary, a torch may be needed to heat ring gear (3).
Note: Identify the orientation of the teeth on the flywheel ring gear (3).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A -
Guide Stud
M12 - 1.25 by 100 mm
2
B 138-7573 Link Bracket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
4/6
262D Skid Steer Loader KTS00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 4 g02798923
Always wear protective gloves when handling parts that have been
heated.
1. If flywheel ring gear (3) was removed, follow Step 1.a through Step 1.c in order to install
ring gear (3) to flywheel (1).
a. Identify the orientation of teeth on new ring gear (3).
Note: The chamfered side of ring gear teeth must face toward the starting motor when
the flywheel is installed. This position will ensure the correct engagement of the
starting motor.
b. Raise heat of flywheel ring gear (3) in an oven to a maximum temperature of 250 °C
(482 °F) prior to installation.
Note: Do not use a torch to heat the ring gear.
c. Ensure that the orientation of ring gear (3) is correct and quickly install the ring gear
onto flywheel (1).
5/6
262D Skid Steer Loader KTS00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 5 g02798921
2. Install Tooling (B) and a suitable lifting device on flywheel (1). The weight of flywheel (1)
is approximately 30 kg (66 lb).
3. Install Tooling (A) into the crankshaft.
4. Use the lifting device to position flywheel (1) onto Tooling (A).
5. Install bolts (2) to flywheel (1).
6. Remove Tooling (A).
Illustration 6 g02794543
7. Install remaining bolts (2) to flywheel (1). Apply engine oil to bolts. Tighten bolts (2) to a
torque of 98 to 107 N·m (72 to 80 lb ft).
8. Check the run out of the flywheel. Refer to Specifications, "Flywheel" for further
information.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Nov 17 23:41:40 UTC+0800 2019
6/6
262D Skid Steer Loader KTS00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 262D SKID STEER LOADER KTS
Configuration: 262D Skid Steer Loader KTS00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
C2.6 and C3.3B Engines for Caterpillar Built Machines
Media Number -UENR0137-11 Publication Date -01/08/2015 Date Updated -12/07/2018
i05242540
Crankshaft Rear Seal and Wear Sleeve - Remove - Includes
Crankshaft Gear
SMCS - 1161-011; 7558-011
Removal Procedure
Start By:
a. Remove the flywheel.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Place the engine at top dead center.
1/2
262D Skid Steer Loader KTS00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 1 g02799897
2. Use a screw driver to remove rear seal (1).
Illustration 2 g02799899
3. Check the alignment of crankshaft gear (2) and camshaft gear (3). Remove crankshaft gear
(2) and ring seal.
Illustration 3 g02799901
4. Place crankshaft gear (2) with wear sleeve (4) in a suitable vice. Remove wear sleeve (4)
with a suitable chisel.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Nov 17 23:42:39 UTC+0800 2019
2/2
262D Skid Steer Loader KTS00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 262D SKID STEER LOADER KTS
Configuration: 262D Skid Steer Loader KTS00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
C2.6 and C3.3B Engines for Caterpillar Built Machines
Media Number -UENR0137-11 Publication Date -01/08/2015 Date Updated -12/07/2018
i05242547
Crankshaft Rear Seal and Wear Sleeve - Install - Includes
Crankshaft Gear
SMCS - 1161-012; 7558-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
390-1146 Crankshaft Rear Seal and Wear Sleeve Driver(1)
1
423-9665 Crank shaft Rear Seal and Wear Sleeve Driver(2)
1
(1)
Used for the C3.3B
(2)
Used for the C2.6
Note: Refer to Specification UENR0995 "Engine Design" for non-specified engine Torque
Values.
1/2
262D Skid Steer Loader KTS00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 1 g02800138
1. Place wear sleeve (4) on crankshaft gear (2). Position Tooling (A). Use a suitable press and
install wear sleeve (4).
Illustration 2 g02799899
2. Align crankshaft gear (2) with camshaft gear (3). Install crankshaft gear (2) into the
flywheel housing.
Illustration 3 g02800140
3. Apply clean engine oil on the lip of crankshaft rear seal (1). Use Tooling (A) in order to
install crankshaft rear seal (1).
End By:
a. Install the flywheel.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Nov 17 23:43:38 UTC+0800 2019
2/2
262D Skid Steer Loader KTS00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 262D SKID STEER LOADER KTS
Configuration: 262D Skid Steer Loader KTS00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
C2.6 and C3.3B Engines for Caterpillar Built Machines
Media Number -UENR0137-11 Publication Date -01/08/2015 Date Updated -12/07/2018
i05242551
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Stud
M12 x 1.25 by 100 mm
2
B 138-7575 Link Brackets 2
Start By:
a. Remove the flywheel.
b. Remove the rear crankshaft seal.
Note: Refer to Specification UENR0995 "Engine Design" for non-specified engine Torque
Values.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
262D Skid Steer Loader KTS00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 1 g02794824
1. Remove two bolts (3) from flywheel housing (1).
2. Install Tooling (A) into flywheel housing (1).
3. Install Tooling (B). Install a suitable lifting device to flywheel housing (1). The weight of
flywheel housing (1) is approximately 25 kg (55 lb).
4. Remove remaining six bolts (3) and 8 bolts (2) from flywheel housing (1).
5. Remove flywheel housing (1) from the cylinder block.
Illustration 2 g02794825
6. Remove bearing (4).
7. Remove the gasket (5).
8. If necessary, remove the dowels from the cylinder block.
Installation Procedure
1. Install flywheel housing (1) in the reverse order of removal.
2/3
262D Skid Steer Loader KTS00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
21. Illustration 3 g02863884
a. Install liquid gasket to the seam between the lower crankcase section (7) and the
upper crankcase section (6).
b. For the C3.3B tighten 8 bolts (3) and 8 bolts (2) to a torque of 103 to 117 N·m
(76 to 87 lb ft).
c. For the C2.6 tighten 8 bolts (3) and 8 bolts (2) to a torque of 78 to 90 N·m
(58 to 66 lb ft).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Nov 17 23:44:38 UTC+0800 2019
3/3
262D Skid Steer Loader KTS00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 262D SKID STEER LOADER KTS
Configuration: 262D Skid Steer Loader KTS00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
C2.6 and C3.3B Engines for Caterpillar Built Machines
Media Number -UENR0137-11 Publication Date -01/08/2015 Date Updated -12/07/2018
i05242553
Crankshaft Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Start By:
a. Remove the v-belt.
Note: Refer to Specification UENR0995 "Engine Design" for non-specified engine Torque
Values.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
262D Skid Steer Loader KTS00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...