This document provides instructions for removing and installing a flywheel housing on a 416C Backhoe Loader with a 3054 engine. It describes using lifting brackets and removing mounting bolts to detach the housing. Cleaning surfaces and replacing seals is emphasized. Diagrams illustrate the housing and bolt locations. Proper safety procedures and required tools are also outlined.
Caterpillar cat 416 c backhoe loader (prefix 1xr) service repair manual (1xr0...fjjkskekfsmem
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel by installing a lifting tool, removing bolts, and lifting it off.
2) Install the flywheel by heating and positioning the ring gear, installing the flywheel with a lifting tool and bolts, and tightening.
3) Remove the crankshaft rear seal by removing housing bolts and hardware.
4) Install the crankshaft rear seal by pressing in the seal, lubricating, positioning the housing, and replacing bolts.
Caterpillar cat 416 c backhoe loader (prefix 1xr) service repair manual (1xr0...fjskekskkemm
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves removing mounting bolts from the top and bottom of the housing and lifting it away using lifting brackets. The installation procedure specifies cleaning mating surfaces, positioning the housing on dowels in the cylinder block, and installing mounting bolts while supporting the housing. Tools required include lifting brackets and bolts of the appropriate size. Safety notices are provided to keep parts clean and contain fluids.
Caterpillar cat 416 c backhoe loader (prefix 1xr) service repair manual (1xr0...jskefksmemwe
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It includes:
- Tools and parts needed for the job.
- Step-by-step instructions for removing the flywheel using a lifting device and removing bolts, then removing the crankshaft rear seal, gasket and housing.
- Instructions for installing the crankshaft rear seal using a press, lubricating the seal and crankshaft, and reinstalling the housing and bolts.
Caterpillar cat 416 c backhoe loader (prefix 1xr) service repair manual (1xr0...fjsjejfksekmme
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It includes:
- Tools and parts needed for the job.
- Step-by-step instructions for removing the flywheel using a lifting device and removing bolts, then removing the crankshaft rear seal, gasket and housing.
- Instructions for installing the crankshaft rear seal using a press, lubricating the seal and crankshaft, and reinstalling the housing and bolts.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the housing, which include removing mounting bolts from the top and sides of the housing and lifting it off using lifting brackets. Reinstallation involves cleaning mating surfaces, placing the housing on the cylinder block, and reinstalling the mounting bolts with the specified torque. Instructions are also provided for removing and installing the crankshaft rear seal and flywheel.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves removing mounting bolts from the top and sides of the housing using lifting tools. The installation procedure specifies cleaning mating surfaces, placing the housing on dowels in the cylinder block, and installing mounting bolts with the specified torque. Tools required include link brackets and a soft faced hammer.
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and multi-step processes for both removal and installation. Removal of the flywheel requires using a lifting device to remove bolts and separate the flywheel. Installation requires heating, positioning, and torquing components in the correct order.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the housing, which include removing mounting bolts from the top and sides of the housing and lifting it off using lifting brackets. Reinstallation involves cleaning mating surfaces, placing the housing on the cylinder block, and reinstalling the mounting bolts with the specified torque. Instructions are also provided for removing and installing the crankshaft rear seal and flywheel.
Caterpillar cat 416 c backhoe loader (prefix 1xr) service repair manual (1xr0...fjjkskekfsmem
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel by installing a lifting tool, removing bolts, and lifting it off.
2) Install the flywheel by heating and positioning the ring gear, installing the flywheel with a lifting tool and bolts, and tightening.
3) Remove the crankshaft rear seal by removing housing bolts and hardware.
4) Install the crankshaft rear seal by pressing in the seal, lubricating, positioning the housing, and replacing bolts.
Caterpillar cat 416 c backhoe loader (prefix 1xr) service repair manual (1xr0...fjskekskkemm
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves removing mounting bolts from the top and bottom of the housing and lifting it away using lifting brackets. The installation procedure specifies cleaning mating surfaces, positioning the housing on dowels in the cylinder block, and installing mounting bolts while supporting the housing. Tools required include lifting brackets and bolts of the appropriate size. Safety notices are provided to keep parts clean and contain fluids.
Caterpillar cat 416 c backhoe loader (prefix 1xr) service repair manual (1xr0...jskefksmemwe
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It includes:
- Tools and parts needed for the job.
- Step-by-step instructions for removing the flywheel using a lifting device and removing bolts, then removing the crankshaft rear seal, gasket and housing.
- Instructions for installing the crankshaft rear seal using a press, lubricating the seal and crankshaft, and reinstalling the housing and bolts.
Caterpillar cat 416 c backhoe loader (prefix 1xr) service repair manual (1xr0...fjsjejfksekmme
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It includes:
- Tools and parts needed for the job.
- Step-by-step instructions for removing the flywheel using a lifting device and removing bolts, then removing the crankshaft rear seal, gasket and housing.
- Instructions for installing the crankshaft rear seal using a press, lubricating the seal and crankshaft, and reinstalling the housing and bolts.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the housing, which include removing mounting bolts from the top and sides of the housing and lifting it off using lifting brackets. Reinstallation involves cleaning mating surfaces, placing the housing on the cylinder block, and reinstalling the mounting bolts with the specified torque. Instructions are also provided for removing and installing the crankshaft rear seal and flywheel.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves removing mounting bolts from the top and sides of the housing using lifting tools. The installation procedure specifies cleaning mating surfaces, placing the housing on dowels in the cylinder block, and installing mounting bolts with the specified torque. Tools required include link brackets and a soft faced hammer.
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and multi-step processes for both removal and installation. Removal of the flywheel requires using a lifting device to remove bolts and separate the flywheel. Installation requires heating, positioning, and torquing components in the correct order.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the housing, which include removing mounting bolts from the top and sides of the housing and lifting it off using lifting brackets. Reinstallation involves cleaning mating surfaces, placing the housing on the cylinder block, and reinstalling the mounting bolts with the specified torque. Instructions are also provided for removing and installing the crankshaft rear seal and flywheel.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves removing mounting bolts from the top and sides of the housing using lifting tools. The installation procedure specifies cleaning mating surfaces, placing the housing on dowels in the cylinder block, and tightening mounting bolts to specified torques. Tools, safety precautions, and references to other repair procedures are also listed.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the housing, which include removing mounting bolts from the top and sides of the housing and lifting it off using lifting brackets. Reinstallation involves cleaning mating surfaces, placing the housing on the cylinder block, and reinstalling the mounting bolts with the specified torque. Instructions are also provided for removing and installing the crankshaft rear seal and flywheel.
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and multi-step processes for both removal and installation. Removal of the flywheel requires using a lifting device to remove bolts and separate the flywheel. Installation requires heating, positioning, and torquing components in the correct order.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the housing, which include removing mounting bolts from the top and sides of the housing and lifting it off using lifting brackets. Reinstallation involves cleaning mating surfaces, placing the housing on the cylinder block, and reinstalling the mounting bolts with the specified torque. Instructions are also provided for removing and installing the crankshaft rear seal and flywheel.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the housing, which include removing mounting bolts from the top and sides of the housing and lifting it off using lifting brackets. Reinstallation involves cleaning mating surfaces, placing the housing on the cylinder block, and reinstalling the mounting bolts with the specified torque. Instructions are also provided for removing and installing the crankshaft rear seal and flywheel.
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and multi-step processes for both removal and installation. Removal of the flywheel requires using a lifting device to remove bolts and separate the flywheel. Installation requires heating, positioning, and torquing components in the correct order.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the housing, which include removing mounting bolts from the top and sides of the housing and lifting it off using lifting brackets. Reinstallation involves cleaning mating surfaces, placing the housing on the cylinder block, and reinstalling the mounting bolts with the specified torque. Instructions are also provided for removing and installing the crankshaft rear seal and flywheel.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves removing mounting bolts from the top and sides of the housing using lifting tools. The installation procedure specifies cleaning mating surfaces, placing the housing on dowels in the cylinder block, and tightening mounting bolts to specified torques. Tools, safety precautions, and references to other repair procedures are also listed.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves removing mounting bolts from the top and sides of the housing using lifting tools. The installation procedure specifies cleaning mating surfaces, placing the housing on dowels in the cylinder block, and tightening mounting bolts to specified torques. Tools, safety precautions, and references to other repair procedures are also listed.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and sides of the housing, attaching lifting tools to the housing, and using hammers to separate the housing from the cylinder block. The installation procedure specifies cleaning mating surfaces and inserting a new felt seal if needed before placing the housing on dowels and bolts and tightening to the specified torque. Tools including link brackets and lifting devices are listed.
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the step-by-step procedures for both removal and installation. The instructions include illustrations showing the specific engine components and numbering the steps in the process. It provides details for engines that have both a 14 bolt housing assembly and a 10 bolt housing assembly.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools to the housing, and using hammers to separate the housing from the cylinder block. The installation procedure specifies cleaning mating surfaces and inserting a new felt seal if needed before placing the housing on the cylinder block and securing it with mounting bolts. Tools including link brackets and lifting devices are listed.
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the step-by-step procedures for both removal and installation. The instructions include illustrations showing the specific engine components and numbering the steps in the process. It provides details for engines that have both a 14 bolt housing assembly and a 10 bolt housing assembly.
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to remove the flywheel using a lifting device and remove the bolts and bearing housing. To install the flywheel, it describes heating the flywheel ring gear, positioning the flywheel and tightening the bolts. It also provides instructions for removing and installing the crankshaft rear seal, which involves removing housing bolts and installing the seal using a press and installer tool.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools to the housing, and using hammers to separate the housing from the cylinder block. The installation procedure specifies cleaning mating surfaces and inserting a new felt seal if needed before placing the housing on the cylinder block and securing it with mounting bolts. Tools including link brackets and lifting devices are listed.
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the step-by-step procedures for both removal and installation. The instructions include illustrations showing the specific engine components and numbering the steps in the process. It provides details for engines that have both a 14 bolt housing assembly and a 10 bolt housing assembly.
Caterpillar Cat 160M Motor Grader (Prefix D9T) Service Repair Manual (D9T0000...f7useijdkdmdm
This document provides disassembly instructions for the transmission of a 160M Motor Grader. It lists over 50 steps to fully disassemble the transmission along with required tools. These steps include removing components like the transmission housing, clutch assemblies, gears, seals, pistons, and sensors. Diagrams are provided to illustrate where each component is located and how to remove it. Precautions are mentioned regarding fluid containment and releasing spring forces when disassembling parts.
Caterpillar Cat 307D Mini Hydraulic Excavator (Prefix DSG) Service Repair Man...f7useijdkdmdm
The document provides instructions for removing and installing various engine components on a 307D Mini Hydraulic Excavator including the fuel filter and water separator base, engine oil filter and oil filter base, and air cleaner. The procedures describe draining fluids, disconnecting hoses, removing bolts and filters, cleaning parts, applying oil, and reinstalling components in the reverse order of removal. Safety precautions are provided to prevent injury and contain fluids.
Caterpillar Cat 307E2 Mini Hydraulic Excavator (Prefix KC9) Service Repair Ma...f7useijdkdmdm
The document provides instructions for removing and installing various components of a 307E2 Mini Hydraulic Excavator engine, including the fuel manifold, fuel injection lines, fuel injection pump, electronic unit injector, turbocharger, and exhaust gas recirculation valve. Safety precautions are provided, such as wearing protective equipment when draining fluids and precautions for high pressure fuel lines. The procedures note removing retaining bolts, clamps, and hoses and reinstalling components in the reverse order.
The document provides instructions for removing and installing the valve mechanism cover on a Caterpillar 3054 diesel engine. The removal procedure involves loosening the breather hose clamp, removing three nuts and washers to detach the valve cover, and removing seals from the valve cover and oil filler cap. The installation procedure involves replacing any seals and gaskets, placing the valve cover into position, and securing it with three nuts, washers, and tightening the breather hose clamp. Safety notices are provided to keep parts clean and contain fluids.
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar C4.4 engine. To remove the flywheel, two guide bolts must be inserted and bolts removed using a lifting device due to the flywheel's weight of approximately 71 kg. To install the flywheel, a lifting device is also used to position the flywheel onto the guide bolts before installing and tightening the bolts. Removing the crankshaft rear seal involves using a socket to remove torx screws, while installing the new seal requires aligning its locators with the cylinder block holes and tightening screws in a specific sequence.
This document provides instructions for installing an engine in a 420F2 backhoe loader. It outlines 17 steps for installing the engine, connecting various components like the transmission, alternator, and fuel system. Tools required are listed. Photos illustrate each step, and safety notices are included.
More Related Content
Similar to Caterpillar Cat 416C Backhoe Loader (Prefix 1XR) Service Repair Manual (1XR02250-02261).pdf
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves removing mounting bolts from the top and sides of the housing using lifting tools. The installation procedure specifies cleaning mating surfaces, placing the housing on dowels in the cylinder block, and tightening mounting bolts to specified torques. Tools, safety precautions, and references to other repair procedures are also listed.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the housing, which include removing mounting bolts from the top and sides of the housing and lifting it off using lifting brackets. Reinstallation involves cleaning mating surfaces, placing the housing on the cylinder block, and reinstalling the mounting bolts with the specified torque. Instructions are also provided for removing and installing the crankshaft rear seal and flywheel.
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and multi-step processes for both removal and installation. Removal of the flywheel requires using a lifting device to remove bolts and separate the flywheel. Installation requires heating, positioning, and torquing components in the correct order.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the housing, which include removing mounting bolts from the top and sides of the housing and lifting it off using lifting brackets. Reinstallation involves cleaning mating surfaces, placing the housing on the cylinder block, and reinstalling the mounting bolts with the specified torque. Instructions are also provided for removing and installing the crankshaft rear seal and flywheel.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the housing, which include removing mounting bolts from the top and sides of the housing and lifting it off using lifting brackets. Reinstallation involves cleaning mating surfaces, placing the housing on the cylinder block, and reinstalling the mounting bolts with the specified torque. Instructions are also provided for removing and installing the crankshaft rear seal and flywheel.
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and multi-step processes for both removal and installation. Removal of the flywheel requires using a lifting device to remove bolts and separate the flywheel. Installation requires heating, positioning, and torquing components in the correct order.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the housing, which include removing mounting bolts from the top and sides of the housing and lifting it off using lifting brackets. Reinstallation involves cleaning mating surfaces, placing the housing on the cylinder block, and reinstalling the mounting bolts with the specified torque. Instructions are also provided for removing and installing the crankshaft rear seal and flywheel.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves removing mounting bolts from the top and sides of the housing using lifting tools. The installation procedure specifies cleaning mating surfaces, placing the housing on dowels in the cylinder block, and tightening mounting bolts to specified torques. Tools, safety precautions, and references to other repair procedures are also listed.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves removing mounting bolts from the top and sides of the housing using lifting tools. The installation procedure specifies cleaning mating surfaces, placing the housing on dowels in the cylinder block, and tightening mounting bolts to specified torques. Tools, safety precautions, and references to other repair procedures are also listed.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and sides of the housing, attaching lifting tools to the housing, and using hammers to separate the housing from the cylinder block. The installation procedure specifies cleaning mating surfaces and inserting a new felt seal if needed before placing the housing on dowels and bolts and tightening to the specified torque. Tools including link brackets and lifting devices are listed.
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the step-by-step procedures for both removal and installation. The instructions include illustrations showing the specific engine components and numbering the steps in the process. It provides details for engines that have both a 14 bolt housing assembly and a 10 bolt housing assembly.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools to the housing, and using hammers to separate the housing from the cylinder block. The installation procedure specifies cleaning mating surfaces and inserting a new felt seal if needed before placing the housing on the cylinder block and securing it with mounting bolts. Tools including link brackets and lifting devices are listed.
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the step-by-step procedures for both removal and installation. The instructions include illustrations showing the specific engine components and numbering the steps in the process. It provides details for engines that have both a 14 bolt housing assembly and a 10 bolt housing assembly.
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to remove the flywheel using a lifting device and remove the bolts and bearing housing. To install the flywheel, it describes heating the flywheel ring gear, positioning the flywheel and tightening the bolts. It also provides instructions for removing and installing the crankshaft rear seal, which involves removing housing bolts and installing the seal using a press and installer tool.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools to the housing, and using hammers to separate the housing from the cylinder block. The installation procedure specifies cleaning mating surfaces and inserting a new felt seal if needed before placing the housing on the cylinder block and securing it with mounting bolts. Tools including link brackets and lifting devices are listed.
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the step-by-step procedures for both removal and installation. The instructions include illustrations showing the specific engine components and numbering the steps in the process. It provides details for engines that have both a 14 bolt housing assembly and a 10 bolt housing assembly.
Similar to Caterpillar Cat 416C Backhoe Loader (Prefix 1XR) Service Repair Manual (1XR02250-02261).pdf (16)
Caterpillar Cat 160M Motor Grader (Prefix D9T) Service Repair Manual (D9T0000...f7useijdkdmdm
This document provides disassembly instructions for the transmission of a 160M Motor Grader. It lists over 50 steps to fully disassemble the transmission along with required tools. These steps include removing components like the transmission housing, clutch assemblies, gears, seals, pistons, and sensors. Diagrams are provided to illustrate where each component is located and how to remove it. Precautions are mentioned regarding fluid containment and releasing spring forces when disassembling parts.
Caterpillar Cat 307D Mini Hydraulic Excavator (Prefix DSG) Service Repair Man...f7useijdkdmdm
The document provides instructions for removing and installing various engine components on a 307D Mini Hydraulic Excavator including the fuel filter and water separator base, engine oil filter and oil filter base, and air cleaner. The procedures describe draining fluids, disconnecting hoses, removing bolts and filters, cleaning parts, applying oil, and reinstalling components in the reverse order of removal. Safety precautions are provided to prevent injury and contain fluids.
Caterpillar Cat 307E2 Mini Hydraulic Excavator (Prefix KC9) Service Repair Ma...f7useijdkdmdm
The document provides instructions for removing and installing various components of a 307E2 Mini Hydraulic Excavator engine, including the fuel manifold, fuel injection lines, fuel injection pump, electronic unit injector, turbocharger, and exhaust gas recirculation valve. Safety precautions are provided, such as wearing protective equipment when draining fluids and precautions for high pressure fuel lines. The procedures note removing retaining bolts, clamps, and hoses and reinstalling components in the reverse order.
The document provides instructions for removing and installing the valve mechanism cover on a Caterpillar 3054 diesel engine. The removal procedure involves loosening the breather hose clamp, removing three nuts and washers to detach the valve cover, and removing seals from the valve cover and oil filler cap. The installation procedure involves replacing any seals and gaskets, placing the valve cover into position, and securing it with three nuts, washers, and tightening the breather hose clamp. Safety notices are provided to keep parts clean and contain fluids.
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar C4.4 engine. To remove the flywheel, two guide bolts must be inserted and bolts removed using a lifting device due to the flywheel's weight of approximately 71 kg. To install the flywheel, a lifting device is also used to position the flywheel onto the guide bolts before installing and tightening the bolts. Removing the crankshaft rear seal involves using a socket to remove torx screws, while installing the new seal requires aligning its locators with the cylinder block holes and tightening screws in a specific sequence.
This document provides instructions for installing an engine in a 420F2 backhoe loader. It outlines 17 steps for installing the engine, connecting various components like the transmission, alternator, and fuel system. Tools required are listed. Photos illustrate each step, and safety notices are included.
This document provides instructions for removing and installing an engine from a 420F2 backhoe loader. It outlines 19 steps to remove the engine, which includes draining fluids, disconnecting wiring harnesses, removing mounting hardware, and lifting the engine out. It then describes 19 steps to install the engine in reverse order, including lowering the engine into place, reconnecting wiring, refilling fluids, and reinstalling ancillary components. The purpose is to provide technicians with a procedure to safely remove and reinstall the engine.
This document provides instructions for removing and installing the flywheel, crankshaft rear seal, and crankshaft wear sleeve on a Caterpillar 3054C engine. The removal procedure for the flywheel involves using guide bolts and a link bracket to support the flywheel weight before removing all setscrews. The crankshaft rear seal housing assembly must be replaced as a unit if removed. A plastic sleeve is used to protect the crankshaft rear seal during installation. A puller and spacer are used to remove the crankshaft wear sleeve, which is used to reclaim a worn crankshaft seal surface.
This document provides instructions for installing an engine on a 416F2 Backhoe Loader. It describes attaching lifting equipment to the engine, aligning and bolting the bell housing and flywheel, installing engine mounts and accessories like the alternator, air conditioning compressor and fuel system components. The 17 step procedure includes attaching hoses, wiring harnesses and filling fluids before installing remaining panels and covers.
This document provides instructions for removing and installing various engine components on a Caterpillar 3054C engine, including:
- Lifters can be removed and installed using a telescoping magnet. Proper identification and lubrication is required.
- Camshaft removal requires removing the rocker shaft assembly, pushrods, and front housing first. The camshaft is then carefully removed and installed.
- Camshaft bearings are removed and installed using a special tool, ensuring the oil hole is properly aligned during installation.
- Piston cooling jets are accessed by first removing the engine oil pan and then removing a setscrew to access the assembly.
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader. It describes removing the flywheel by taking out bolts and using guide bolts and lifting equipment due to the flywheel's weight of approximately 155 pounds. For installing the flywheel, the instructions specify cleaning components, heating the ring gear, lifting the flywheel into place, and tightening bolts to the specified torque. Removing the crankshaft rear seal involves using a socket to remove screws, while installing requires aligning and pressing the new seal onto the crankshaft flange and torquing screws to the specified value.
The document provides instructions for installing a flywheel and crankshaft rear seal on a Caterpillar 3054C engine. It describes cleaning and preparing the components, heating the ring gear to install it on the flywheel, installing guide bolts and lifting brackets to position the flywheel, and tightening the bolts to specification. It also explains that the crankshaft rear seal is replaced as an assembly, including inserting a plastic sleeve to protect the seal during installation and tightening setscrews to secure the assembly.
1. The document provides assembly instructions for the transmission of a 416D Backhoe Loader.
2. It describes assembling the transmission in major components and then assembling the components together.
3. Cleanliness is important during assembly and all parts should be cleaned and inspected before assembly, applying a light film of transmission oil to components.
This document provides instructions for removing and installing the flywheel housing on a Caterpillar 3054 engine. The removal procedure involves removing mounting bolts from the top and bottom of the housing and using lifting tools to detach the housing from the cylinder block. The installation procedure specifies cleaning parts, placing the housing in position, and tightening mounting bolts to secure the housing. Tools required include link brackets for lifting.
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It includes removal and installation procedures with lists of required tools and illustrations showing the step-by-step processes. The instructions cover both engines with a 14 bolt housing assembly and engines with a 10 bolt housing assembly.
This document provides instructions for removing and installing a crankshaft rear seal on a Caterpillar 3054 engine. It describes the necessary tools and parts, safety precautions, and step-by-step procedures for both removing the old seal and installing the new one. The procedures are separated into sections for engines with a 14-bolt housing assembly versus a 10-bolt housing assembly. Precise instructions are given for lubricating parts, inserting the seal, aligning components, and tightening bolts to the specified torque.
This document provides instructions for removing the crankshaft front seal from a Caterpillar 3054 engine. The steps are:
1. Use a drill bit to drill out the spot welds securing the seal retainer.
2. Remove the retainer, crankshaft front seal, and gasket from the front cover.
3. Inspect the front cover dowels and replace if needed before installing the new seal.
This document provides instructions for removing and installing a crankshaft pulley on a Caterpillar 3054 engine. It describes using a puller tool to remove the pulley and pressing the pulley onto the crankshaft during installation. Tightening specifications and safety notices are also included.
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and multi-step processes for both removal and installation. For the flywheel, it details removing bolts and lifting the flywheel off. For the crankshaft rear seal, it differentiates between engines with 14-bolt and 10-bolt housings and removing or installing the seal and housing. Precautions are provided regarding cleanliness and proper torque specifications.
Caterpillar Cat 329D L Excavator (Prefix DTZ) Service Repair Manual (DTZ00001...f7useijdkdmdm
This document provides instructions for removing and installing the water temperature regulator on a Caterpillar C7 engine. It describes:
1. Draining the engine coolant below the level of the water temperature regulator.
2. Disconnecting the hose from the regulator cover by loosening the clamp.
3. Removing the bolts securing the regulator housing and removing the housing to access the internal components.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
2. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 416C BACKHOE LOADER 1XR
Configuration: 416C Backhoe Loader Center Pivot, Parallel Lift 1XR02250-02261 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i04406238
Flywheel - Remove
SMCS - 1156-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
416C Backhoe Loader Center Pivot, Parallel Lift 1XR02250-02261 (MACHINE) PO...
2019/12/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00546794
Typical Example. Different lifting device shown than what is called out in the Table.
Illustration 2 g00546793
1. Install Tool (A) and a suitable lifting device on flywheel (1) .
2. Remove bolts (3) and bearing housing (4) .
3. Remove six bolts (2) and the washers from the flywheel.
Note: The 3054 and 3056 marine engines used several bolt patterns to attach the flywheel to
the crankshaft. There are drilled holes that are not used in the crankshaft and in the
flywheel.
4. Use the suitable lifting device in order to remove flywheel (1) . The weight of flywheel (1)
and the flywheel ring gear is 53 kg (120 lb).
5. If removal of the flywheel ring gear is necessary, place an index mark on the chamfer of the
flywheel ring gear for the installation process.
Illustration 3 g00546795
2/3
416C Backhoe Loader Center Pivot, Parallel Lift 1XR02250-02261 (MACHINE) PO...
2019/12/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 6. Use a hammer and a punch in order to remove flywheel ring gear (5) from flywheel (1) .
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Dec 30 17:40:31 UTC+0800 2019
3/3
416C Backhoe Loader Center Pivot, Parallel Lift 1XR02250-02261 (MACHINE) PO...
2019/12/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 416C BACKHOE LOADER 1XR
Configuration: 416C Backhoe Loader Center Pivot, Parallel Lift 1XR02250-02261 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i04406239
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
Always wear protective gloves when handling parts that have been
heated.
1/2
416C Backhoe Loader Center Pivot, Parallel Lift 1XR02250-02261 (MACHINE) PO...
2019/12/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 1 g00803517
Typical Example. Different Lifting device shown than what is called out in the table.
1. If flywheel ring gear (5) was removed, heat flywheel ring gear (5) to a temperature of 250 °
C (480 °F).
Note: Do not use a torch to heat the flywheel ring gear.
2. Install flywheel ring gear (5) on flywheel (1) .
Note: Ensure that the chamfer of the flywheel ring gear is in the correct position on the
flywheel.
3. Install Tool (A) and a suitable lifting device on flywheel (1) and position flywheel (1) in the
flywheel housing. The weight of flywheel (1) and flywheel ring gear (5) is 53 kg (120 lb).
Illustration 2 g00546793
4. Install six bolts (2) and the washers that hold flywheel (1) in position. Tighten the bolts to a
torque of 105 N·m (77 lb ft).
5. Put bearing housing (4) in position on the flywheel. Install four bolts (3) that fasten bearing
housing (4) to the flywheel.
6. Refer to the Specifications Module, "Flywheel" topic for information on inspecting the
flywheel.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Dec 30 17:41:27 UTC+0800 2019
2/2
416C Backhoe Loader Center Pivot, Parallel Lift 1XR02250-02261 (MACHINE) PO...
2019/12/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 416C BACKHOE LOADER 1XR
Configuration: 416C Backhoe Loader Center Pivot, Parallel Lift 1XR02250-02261 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01741403
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/3
416C Backhoe Loader Center Pivot, Parallel Lift 1XR02250-02261 (MACHINE) PO...
2019/12/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Engines with 14 Bolt Housing Assembly
Illustration 1 g00632744
The flywheel housing has been removed for photographic purposes only.
1. Remove bolts (1) from housing (3).
2. Remove socket head bolts (2) from housing (3).
3. Remove the crankshaft rear seal, the gasket, and housing (3) from the dowels in the cylinder
block.
Engines with 10 Bolt Housing Assembly
Note: The 10 bolt housing assembly is manufactured as a one-piece assembly. The 10 bolt
housing assembly is NOT adaptable to engines that have the 14 bolt housing assembly.
Illustration 2 g00830867
2/3
416C Backhoe Loader Center Pivot, Parallel Lift 1XR02250-02261 (MACHINE) PO...
2019/12/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 1. Remove the bolts in reverse order of the numbered sequence. Refer to Illustration 2.
2. Remove the one-piece housing assembly from the cylinder block.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Dec 30 17:42:24 UTC+0800 2019
3/3
416C Backhoe Loader Center Pivot, Parallel Lift 1XR02250-02261 (MACHINE) PO...
2019/12/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 416C BACKHOE LOADER 1XR
Configuration: 416C Backhoe Loader Center Pivot, Parallel Lift 1XR02250-02261 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01605362
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
9U-6205 Rear Seal Installer 1
1P-0510 Driver Group 1
B FT-2806 Alignment Tool 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Engines with 14 Bolt Housing Assembly
1. Inspect the condition of the gasket. Replace the gasket, if necessary.
2. Clean the areas of the parts that will contact each other.
1/4
416C Backhoe Loader Center Pivot, Parallel Lift 1XR02250-02261 (MACHINE) PO...
2019/12/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 1 g00541839
3. Use Tool (A) and a suitable press to install the crankshaft rear seal into the housing. Make
sure that you install the seal to the correct depth in the housing. Refer to Specifications,
"Crankshaft Seals" for additional information.
4. Lubricate the crankshaft flange and the lip of the crankshaft rear seal with clean engine oil.
5. Install Tool (A) onto the crankshaft flange.
6. Put the new gasket for the housing in position on the dowels in the cylinder block.
Illustration 2 g00606404
7. Carefully place housing (3) and crankshaft rear seal (4) over Tool (A) .
8. Position housing (3) on the dowels in the cylinder block.
9. Remove Tool (A) .
2/4
416C Backhoe Loader Center Pivot, Parallel Lift 1XR02250-02261 (MACHINE) PO...
2019/12/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 3 g00606340
The flywheel housing has been removed for photographic purposes only.
10. Install bolts (1) and socket head bolts (2) that fasten housing (3) to the cylinder block.
11. Tighten all of the bolts to a torque of 22 N·m (16 lb ft).
Engines with 10 Bolt Housing Assembly
Note: The 10 bolt housing assembly is manufactured as a one-piece assembly. The 10 bolt
housing assembly is NOT adaptable to engines that have the 14 bolt housing assembly.
1. Ensure that all parts and surfaces of the engine block are clean and free from oil, grease, and
dirt.
Illustration 4 g00831176
3/4
416C Backhoe Loader Center Pivot, Parallel Lift 1XR02250-02261 (MACHINE) PO...
2019/12/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Note: The crankshaft rear seal is lubricated. There is no need to lubricate the seal or the
crankshaft flange before installation.
2. Place housing assembly (3) on crankshaft flange (1) until the housing assembly contacts the
cylinder block face. Plastic sleeve (2) will push out of the housing assembly. Discard the
plastic sleeve after the housing assembly is installed.
3. Place Tool (B) over housing assembly (3). This will center the housing assembly onto the
crankshaft flange.
Illustration 5 g00830867
4. Install the bolts with Tool (B) in position in order to fasten housing assembly (3) to the
cylinder block. Tighten bolts 1 and 2 to a torque of 22 N·m (16 lb ft).
5. Remove Tool (B). Tighten the remaining bolts in sequence to a torque of 22 N·m (16 lb ft).
End By: Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Dec 30 17:43:21 UTC+0800 2019
4/4
416C Backhoe Loader Center Pivot, Parallel Lift 1XR02250-02261 (MACHINE) PO...
2019/12/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 416C BACKHOE LOADER 1XR
Configuration: 416C Backhoe Loader Center Pivot, Parallel Lift 1XR02250-02261 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01741450
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
Start By:
a. Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install".
b. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
1/4
416C Backhoe Loader Center Pivot, Parallel Lift 1XR02250-02261 (MACHINE) PO...
2019/12/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Support the engine with blocks or with a suitable lifting device on a flat level surface.
Illustration 1 g00541891
Typical example
2. Remove mounting bolts (1) from the top of flywheel housing (2).
Illustration 2 g00541892
Typical example
3. Attach Tooling (A) and a suitable lifting device to flywheel housing (2).
4. Remove mounting bolts (3) that attach the flywheel housing to the cylinder block.
2/4
416C Backhoe Loader Center Pivot, Parallel Lift 1XR02250-02261 (MACHINE) PO...
2019/12/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
17. 5. Remove flywheel housing (2). If necessary, hit flywheel housing (2) with a soft faced
hammer in order to separate flywheel housing (2) from the cylinder block. The weight of
flywheel housing (2) is approximately 32 kg (70 lb).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean the rear face of the cylinder block and the mating surface of the flywheel housing.
Inspect the felt seal on the rear flange of the engine oil pan. Replace the felt seal, if
necessary. Inspect the dowels in the cylinder block that align the flywheel housing. Replace
the dowels, if necessary.
Illustration 3 g00541892
2. Use Tooling (A) and a suitable lifting device to position flywheel housing (2) on the dowels
that are on the cylinder block. The weight of flywheel housing (2) is approximately 32 kg
(70 lb).
3. Install mounting bolts (3).
3/4
416C Backhoe Loader Center Pivot, Parallel Lift 1XR02250-02261 (MACHINE) PO...
2019/12/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 4 g00541891
Typical example
4. Install mounting bolts (1) that attach flywheel housing (2) to the cylinder block.
Tighten the bolts for an aluminum flywheel housing to a torque of 70 N·m (52 lb ft).
Tighten the cast iron flywheel housing bolts to the following torque:
M10 "8.8" ... 44 N·m (33 lb ft)
M10 "10.9" ... 63 N·m (46 lb ft)
M12 "8.8" ... 75 N·m (55 lb ft)
M12 "10.9" ... 115 N·m (85 lb ft)
5. Remove Tooling (A) from the flywheel housing.
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
b. Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Dec 30 17:44:18 UTC+0800 2019
4/4
416C Backhoe Loader Center Pivot, Parallel Lift 1XR02250-02261 (MACHINE) PO...
2019/12/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 416C BACKHOE LOADER 1XR
Configuration: 416C Backhoe Loader Center Pivot, Parallel Lift 1XR02250-02261 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01461242
Crankshaft Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Start By:
A. Remove the V-Belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
Illustration 1 g00553762
Typical example
1. Remove three bolts (2) that hold thrust block (3) in position.
2. Remove thrust block (3) from the end of the crankshaft. The thrust block holds the
crankshaft pulley in position on the end of the crankshaft.
3. Remove crankshaft pulley (1) from the engine.
1/2
416C Backhoe Loader Center Pivot, Parallel Lift 1XR02250-02261 (MACHINE) PO...
2019/12/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...