The documents provide instructions for servicing components of a Caterpillar 3306 engine used in a 235 excavator, including:
1) Procedures for removing and installing the automatic timing advance, which involves aligning gears, removing bolts and plates, and using support tools.
2) Disassembling the automatic timing advance unit by removing screws, plates, springs, weights and seals.
3) Reassembling the automatic timing advance unit by installing seals, gears, slides, weights, springs and plates.
The document provides instructions for servicing components of a Caterpillar 3306 engine, including:
1) Procedures for removing and installing the fuel ratio control and fuel shutoff solenoid.
2) Steps for removing the automatic timing advance unit, including using alignment marks and tools to ensure proper timing.
3) Disassembly and assembly instructions for the automatic timing advance unit, involving removing springs, weights, seals and gears.
The document provides instructions for servicing components of a Caterpillar 3306 engine, including:
- Installing the fuel ratio control and connecting fuel lines.
- Removing and installing the fuel shutoff solenoid, applying thread lock compound.
- Removing the automatic timing advance using turning tools to align camshaft gears and pistons, and installing a spacer.
- Disassembling the automatic timing advance unit by removing screws, springs, weights and seals.
- Assembling the automatic timing advance unit and installing seals, springs, weights and screws.
- Installing the automatic timing advance using turning tools to align pins and torquing bolts, and reinstalling
The document provides instructions for servicing components of a Caterpillar 3306 engine, including:
1) Procedures for removing and installing the fuel ratio control and fuel shutoff solenoid.
2) Steps for removing the automatic timing advance unit, including using alignment marks and tools to ensure proper timing.
3) Disassembly and assembly instructions for the automatic timing advance unit, involving removing springs, weights, seals and gears.
The document provides instructions for servicing components of a Caterpillar 3306 engine, including:
- Installing the fuel ratio control and connecting fuel lines.
- Removing and installing the fuel shutoff solenoid, applying thread lock compound.
- Removing the automatic timing advance using turning tools to align camshaft gears and pistons, and installing a spacer.
- Disassembling the automatic timing advance unit by removing screws, springs, weights and seals.
- Assembling the automatic timing advance unit and installing seals, springs, weights and screws.
- Installing the automatic timing advance using turning tools to align pins and torquing bolts, and reinstalling
This service repair manual provides instructions for removing and installing the exhaust manifold and inlet/exhaust valves on a Caterpillar 3306 engine. It details the necessary tools and steps, including:
1) Removing the exhaust manifold by taking off nuts and bolts, fuel lines, and gaskets.
2) Installing a new exhaust manifold by positioning gaskets and bolts and tightening to the specified torque.
3) Removing inlet/exhaust valves using a valve spring compressor and identifying valves.
4) Installing new valves by lubricating, positioning springs and keepers, and ensuring proper installation.
This service repair manual provides instructions for removing and installing the exhaust manifold and inlet/exhaust valves on a Caterpillar 3306 engine. It details the necessary tools and steps, including:
1) Removing the exhaust manifold by taking off nuts and bolts, fuel lines, and gaskets.
2) Installing a new exhaust manifold by positioning gaskets and bolts and tightening to the specified torque.
3) Removing inlet/exhaust valves using a valve spring compressor and identifying valves.
4) Installing new valves by lubricating, positioning springs and keepers, and ensuring proper installation.
This service repair manual provides instructions for removing and installing the exhaust manifold and inlet/exhaust valves on a Caterpillar 3306 engine. It details the necessary tools and procedures, including:
1) Removing the exhaust manifold by taking off nuts and bolts, fuel lines, and gaskets.
2) Installing a new exhaust manifold by positioning gaskets and bolts and tightening to the specified torques.
3) Removing inlet/exhaust valves by compressing springs and removing retainers.
4) Installing new valves by lubricating, positioning springs and installing retainers.
The document provides instructions for removing an engine oil filter base from a Caterpillar 3306 engine. It describes the following steps:
1. Drain the engine oil and remove the oil filter.
2. Remove the bolts securing the oil filter base and remove the base.
3. Clean any debris from the mounting surface before installing a new base.
The instructions are part of a service repair manual for a Caterpillar 235 excavator and focus on properly removing the engine oil filter base.
The document provides instructions for servicing components of a Caterpillar 3306 engine, including:
1) Procedures for removing and installing the fuel ratio control and fuel shutoff solenoid.
2) Steps for removing the automatic timing advance unit, including using alignment marks and tools to ensure proper timing.
3) Disassembly and assembly instructions for the automatic timing advance unit, involving removing springs, weights, seals and gears.
The document provides instructions for servicing components of a Caterpillar 3306 engine, including:
- Installing the fuel ratio control and connecting fuel lines.
- Removing and installing the fuel shutoff solenoid, applying thread lock compound.
- Removing the automatic timing advance using turning tools to align camshaft gears and pistons, and installing a spacer.
- Disassembling the automatic timing advance unit by removing screws, springs, weights and seals.
- Assembling the automatic timing advance unit and installing seals, springs, weights and screws.
- Installing the automatic timing advance using turning tools to align pins and torquing bolts, and reinstalling
The document provides instructions for servicing components of a Caterpillar 3306 engine, including:
1) Procedures for removing and installing the fuel ratio control and fuel shutoff solenoid.
2) Steps for removing the automatic timing advance unit, including using alignment marks and tools to ensure proper timing.
3) Disassembly and assembly instructions for the automatic timing advance unit, involving removing springs, weights, seals and gears.
The document provides instructions for servicing components of a Caterpillar 3306 engine, including:
- Installing the fuel ratio control and connecting fuel lines.
- Removing and installing the fuel shutoff solenoid, applying thread lock compound.
- Removing the automatic timing advance using turning tools to align camshaft gears and pistons, and installing a spacer.
- Disassembling the automatic timing advance unit by removing screws, springs, weights and seals.
- Assembling the automatic timing advance unit and installing seals, springs, weights and screws.
- Installing the automatic timing advance using turning tools to align pins and torquing bolts, and reinstalling
This service repair manual provides instructions for removing and installing the exhaust manifold and inlet/exhaust valves on a Caterpillar 3306 engine. It details the necessary tools and steps, including:
1) Removing the exhaust manifold by taking off nuts and bolts, fuel lines, and gaskets.
2) Installing a new exhaust manifold by positioning gaskets and bolts and tightening to the specified torque.
3) Removing inlet/exhaust valves using a valve spring compressor and identifying valves.
4) Installing new valves by lubricating, positioning springs and keepers, and ensuring proper installation.
This service repair manual provides instructions for removing and installing the exhaust manifold and inlet/exhaust valves on a Caterpillar 3306 engine. It details the necessary tools and steps, including:
1) Removing the exhaust manifold by taking off nuts and bolts, fuel lines, and gaskets.
2) Installing a new exhaust manifold by positioning gaskets and bolts and tightening to the specified torque.
3) Removing inlet/exhaust valves using a valve spring compressor and identifying valves.
4) Installing new valves by lubricating, positioning springs and keepers, and ensuring proper installation.
This service repair manual provides instructions for removing and installing the exhaust manifold and inlet/exhaust valves on a Caterpillar 3306 engine. It details the necessary tools and procedures, including:
1) Removing the exhaust manifold by taking off nuts and bolts, fuel lines, and gaskets.
2) Installing a new exhaust manifold by positioning gaskets and bolts and tightening to the specified torques.
3) Removing inlet/exhaust valves by compressing springs and removing retainers.
4) Installing new valves by lubricating, positioning springs and installing retainers.
The document provides instructions for removing an engine oil filter base from a Caterpillar 3306 engine. It describes the following steps:
1. Drain the engine oil and remove the oil filter.
2. Remove the bolts securing the oil filter base and remove the base.
3. Clean any debris from the mounting surface before installing a new base.
The instructions are part of a service repair manual for a Caterpillar 235 excavator and focus on properly removing the engine oil filter base.
This document provides instructions for removing and installing various engine components on a Caterpillar 3306 engine, including:
- Exhaust manifold removal which involves removing nuts and bolts, fuel lines, and the manifold itself.
- Valve removal requiring use of a valve spring compressor to remove keepers and related parts before removing the valve.
- Valve guide removal and installation using driver tools and ensuring proper height is maintained.
- Valve seat insert removal and installation using extractor tools to press inserts in and out of the cylinder head.
The document provides detailed step-by-step instructions and illustrations for each procedure. Safety notices are included and required tools are listed. Proper cleaning and installation
This document provides instructions for removing and installing an exhaust manifold on a Caterpillar 3306 engine. The procedure involves:
1. Removing the turbocharger, fuel injection lines, exhaust manifold nuts and gaskets.
2. Installing new exhaust manifold gaskets and bolting on the exhaust manifold. Reattaching the fuel lines and installing the turbocharger completes the job.
3. Special tools are required and parts must be kept clean to prevent damage and premature wear. Torque specifications are provided for all fasteners.
Caterpillar cat d25 c articulated dump truck (prefix 9yc) service repair manu...fjkskmmdmme
The document provides instructions for removing, disassembling, assembling, and installing an automatic timing advance unit for a 3306 engine. It includes detailed steps and illustrations. Key steps include using tools to align marks on gears, removing bolts and plates, and ensuring proper installation of seals and springs during assembly. Special care is noted to prevent damage to parts when removing weights and springs.
Caterpillar cat d25 c articulated dump truck (prefix 9yc) service repair manu...fjjskkefksme
The document provides instructions for servicing components of the fuel system for a Caterpillar 3306 engine, including:
1) Installing the fuel ratio control and connecting fuel lines.
2) Removing and installing the fuel shutoff solenoid.
3) Procedures for removing, disassembling, and assembling the automatic timing advance unit.
Caterpillar Cat 235 EXCAVATOR (Prefix 83X) Service Repair Manual (83X00001-00...fjskemmd4r
The document provides instructions for removing and disassembling fuel system components on a Caterpillar 3306 engine, including:
- Removing the fuel priming pump by turning off the fuel supply, removing securing bolts and disconnecting tubes.
- Removing the fuel filter base by turning off the fuel supply, disconnecting lines, and removing bolts and washers.
- Removing the fuel transfer pump by turning off the fuel supply, disconnecting tubes, and removing securing bolts.
- Disassembling the fuel transfer pump by removing springs, seals, valves, piston, sleeve, guide, and housing cover after removing the pump.
Caterpillar Cat 235 EXCAVATOR (Prefix 83X) Service Repair Manual (83X00001-00...jfkksemmdmd
The document provides instructions for removing and disassembling fuel system components on a Caterpillar 3306 engine, including:
- Removing the fuel priming pump by turning off the fuel supply, removing securing bolts and disconnecting tubes.
- Removing the fuel filter base by turning off the fuel supply, disconnecting lines, and removing bolts and washers.
- Removing the fuel transfer pump by turning off the fuel supply, disconnecting tubes, and removing securing bolts.
- Disassembling the fuel transfer pump by removing springs, seals, valves, piston, sleeve, guide, and housing cover components.
Caterpillar Cat 235 EXCAVATOR (Prefix 83X) Service Repair Manual (83X00001-00...gen78guozun
The document provides instructions for removing and disassembling fuel system components on a Caterpillar 3306 engine, including:
- Removing the fuel priming pump by turning off the fuel supply, removing securing bolts and disconnecting tubes.
- Removing the fuel filter base by turning off the fuel supply, disconnecting lines, and removing bolts and washers.
- Removing the fuel transfer pump by turning off the fuel supply, disconnecting tubes, and removing securing bolts.
- Disassembling the fuel transfer pump by removing springs, seals, valves, piston, sleeve, guide, and housing cover components.
The document provides instructions for removing and installing several fuel system components on a Caterpillar 3306 engine, including:
- The fuel priming pump, which is removed by turning off the fuel supply, removing mounting bolts and hoses, and installing in reverse order.
- The fuel filter base, which is removed by disconnecting the fuel line, removing mounting bolts and installing a new gasket if needed.
- The fuel transfer pump, which is removed by turning off the fuel supply, disconnecting tubes and removing mounting bolts.
The fuel transfer pump is then disassembled by removing covers, springs, seals and internal components like pistons, sleeves and valves. Assembly is the
Caterpillar Cat 235 EXCAVATOR (Prefix 83X) Service Repair Manual (83X00001-00...fujskekdjdmd
The document provides instructions for removing and installing various fuel system components on a Caterpillar 3306 engine, including:
- Removing and installing the fuel priming pump.
- Removing and installing the fuel filter base.
- Removing the fuel transfer pump.
- Disassembling and assembling the fuel transfer pump.
The instructions include safety notices and illustrations showing the component locations and part numbers. Technicians are directed to clean parts, replace worn gaskets, and properly contain fluids during the repair process.
Caterpillar Cat 235 EXCAVATOR (Prefix 83X) Service Repair Manual (83X00001-00...ufjskekdjdmw2
The document provides instructions for removing and disassembling fuel system components on a Caterpillar 3306 engine, including:
- Removing the fuel priming pump by turning off the fuel supply, removing securing bolts and disconnecting tubes.
- Removing the fuel filter base by turning off the fuel supply, disconnecting lines, and removing bolts and washers.
- Removing the fuel transfer pump by turning off the fuel supply, disconnecting tubes, and removing securing bolts.
- Disassembling the fuel transfer pump by removing springs, seals, valves, piston, sleeve, guide, and housing cover components.
The document provides instructions for removing and installing several fuel system components on a Caterpillar 3306 engine, including:
- The fuel priming pump, which is removed by turning off the fuel supply, removing mounting bolts and hoses, and installing in reverse order.
- The fuel filter base, which is removed by disconnecting the fuel line, removing mounting bolts and installing a new gasket if needed.
- The fuel transfer pump, which is removed by turning off the fuel supply, disconnecting tubes and removing mounting bolts.
The fuel transfer pump is then disassembled by removing covers, springs, seals and internal components like pistons, sleeves and valves. Assembly is the
Caterpillar Cat 235 EXCAVATOR (Prefix 83X) Service Repair Manual (83X00001-00...fujsked9dikdkd
The document provides instructions for removing and disassembling fuel system components on a Caterpillar 3306 engine, including:
- Removing the fuel priming pump by turning off the fuel supply, removing securing bolts and disconnecting tubes
- Removing the fuel filter base by turning off the fuel supply, disconnecting lines, and removing securing bolts and gaskets
- Removing the fuel transfer pump by turning off the fuel supply, disconnecting tubes, and removing securing bolts
- Disassembling the fuel transfer pump by removing covers, springs, seals, valves, pistons, sleeves, and other internal components
The instructions include safety notices to keep parts clean, contain fluids, and dispose of fluids properly
Caterpillar Cat 277D MULTI TERRAIN LOADER (Prefix NTL) Service Repair Manual ...jfkksemmdmd
This document provides instructions for removing and installing various engine components on a Caterpillar 277D Multi Terrain Loader, including the camshaft gear, engine oil pan, pistons, connecting rods, and related parts. Detailed procedures are given for each component, including required tools and torque specifications. Illustrations are included to supplement the written instructions. Safety notices are also provided to ensure safe handling of fluids.
The document provides instructions for disassembling the piston motor (hydrostatic) on a 279C Compact Track Loader. It lists required tools and outlines 27 steps to fully disassemble the component. Key steps include removing retaining rings, springs, pistons, plates, seals, bearings and other internal parts from the head, barrel assembly and shaft. Safety precautions are provided to prevent injury from parts propelled by released spring forces during disassembly.
This document provides instructions for removing and disassembling the piston pump (hydrostatic) on a 279C2 Compact Track Loader. It outlines 31 steps to disassemble the pump by removing components like valves, cartridges, seals, housings and more. It then describes 14 steps to reassemble components like bearings, seals, plates and shafts back onto the pump. Tools required are also listed.
Caterpillar Cat 277D MULTI TERRAIN LOADER (Prefix FMT) Service Repair Manual ...jfkksemmdmd
The document provides instructions for removing and installing various engine components on a 277D Multi Terrain Loader, including:
1) Removing and installing the diesel particulate filter, which requires disconnecting harness assemblies, removing mounting bolts, and using two people.
2) Removing and installing the inlet manifold, which involves disconnecting hoses and tubes and removing mounting bolts.
3) Procedures for removing and installing inlet and exhaust valve springs safely, which requires using special tools to compress the springs at top dead center.
The document provides instructions for servicing the fuel injection system and governor/camshaft components of a Caterpillar 903C compact wheel loader. It describes procedures for removing and installing fuel injection lines, nozzles, and the governor/camshaft. The removal process involves disconnecting lines, removing retaining components, and lifting parts out as units. Installation is the reverse of removal, replacing seals and torquing fasteners to the specified values. Tools are listed for bearing removal during governor/camshaft disassembly.
Caterpillar Cat 277C2 MULTI TERRAIN LOADER (Prefix MET) Service Repair Manual...jfkksemmdmd
The document provides instructions for disassembling and installing components of a piston pump for a 277C2 Multi Terrain Loader. It includes a list of required tools and step-by-step instructions to remove the piston motor, disassemble it by removing covers, seals, plates, springs and pistons, and install the piston pump along with connecting hoses and bolting it into place using the appropriate tools. Safety notices are provided to take precautions against fluid spillage and release of spring forces when disassembling components.
Caterpillar Cat 277D MULTI TERRAIN LOADER (Prefix MLT) Service Repair Manual ...jfkksemmdmd
1) The document provides instructions for disassembling and assembling the fuel injection pump and governor of a 277D Multi Terrain Loader. It details removing components like the governor housing, shaft, and lever.
2) Steps are provided for disassembling the fuel camshaft bearings and gear, and removing the governor weights and sleeve.
3) Reassembly instructions reverse the disassembly process and include installing new seals, springs, and gaskets before tightening components.
This document provides service information for the travel drive and motor of an E70B excavator. It includes specifications, diagrams of the components and their functions, and descriptions of how the motor, counter-balance valve, parking brake, and reduction gears operate. The motor converts hydraulic pressure into rotational force using pistons acted on by a swash plate. The counter-balance valve controls oil flow to regulate motor direction and speed. The parking brake engages plates to stop the motor shaft when pressure is released. Gears reduce the motor's rotation to turn the excavator tracks.
The document provides instructions for removing and installing the fuel priming pump, fuel filter base, and fuel transfer pump on a Caterpillar EL300 excavator powered by a 3306 engine. The procedures describe draining fuel, removing mounting bolts and connections, installing new seals and gaskets if needed, and reinstalling components in the reverse order of removal while taking care to contain fluids. The fuel transfer pump section also includes instructions for disassembling and assembling the pump components.
The document provides instructions for removing and installing various engine components on a Caterpillar 272D2 skid steer loader, including:
- Inlet and exhaust valves, requiring tools to compress springs and remove parts in the specified order.
- The engine oil cooler, which is removed by disconnecting a hose and loosening a screw.
- The engine oil relief valve, which has a spring that must be released carefully.
- The engine oil pump, removed by taking off cover screws and rotors.
- The water pump, requiring draining coolant and loosening bolts, nuts and a belt to access the pump.
More Related Content
Similar to Caterpillar Cat 235 EXCAVATOR (Prefix 81X) Service Repair Manual (81X00404 and up).pdf
This document provides instructions for removing and installing various engine components on a Caterpillar 3306 engine, including:
- Exhaust manifold removal which involves removing nuts and bolts, fuel lines, and the manifold itself.
- Valve removal requiring use of a valve spring compressor to remove keepers and related parts before removing the valve.
- Valve guide removal and installation using driver tools and ensuring proper height is maintained.
- Valve seat insert removal and installation using extractor tools to press inserts in and out of the cylinder head.
The document provides detailed step-by-step instructions and illustrations for each procedure. Safety notices are included and required tools are listed. Proper cleaning and installation
This document provides instructions for removing and installing an exhaust manifold on a Caterpillar 3306 engine. The procedure involves:
1. Removing the turbocharger, fuel injection lines, exhaust manifold nuts and gaskets.
2. Installing new exhaust manifold gaskets and bolting on the exhaust manifold. Reattaching the fuel lines and installing the turbocharger completes the job.
3. Special tools are required and parts must be kept clean to prevent damage and premature wear. Torque specifications are provided for all fasteners.
Caterpillar cat d25 c articulated dump truck (prefix 9yc) service repair manu...fjkskmmdmme
The document provides instructions for removing, disassembling, assembling, and installing an automatic timing advance unit for a 3306 engine. It includes detailed steps and illustrations. Key steps include using tools to align marks on gears, removing bolts and plates, and ensuring proper installation of seals and springs during assembly. Special care is noted to prevent damage to parts when removing weights and springs.
Caterpillar cat d25 c articulated dump truck (prefix 9yc) service repair manu...fjjskkefksme
The document provides instructions for servicing components of the fuel system for a Caterpillar 3306 engine, including:
1) Installing the fuel ratio control and connecting fuel lines.
2) Removing and installing the fuel shutoff solenoid.
3) Procedures for removing, disassembling, and assembling the automatic timing advance unit.
Caterpillar Cat 235 EXCAVATOR (Prefix 83X) Service Repair Manual (83X00001-00...fjskemmd4r
The document provides instructions for removing and disassembling fuel system components on a Caterpillar 3306 engine, including:
- Removing the fuel priming pump by turning off the fuel supply, removing securing bolts and disconnecting tubes.
- Removing the fuel filter base by turning off the fuel supply, disconnecting lines, and removing bolts and washers.
- Removing the fuel transfer pump by turning off the fuel supply, disconnecting tubes, and removing securing bolts.
- Disassembling the fuel transfer pump by removing springs, seals, valves, piston, sleeve, guide, and housing cover after removing the pump.
Caterpillar Cat 235 EXCAVATOR (Prefix 83X) Service Repair Manual (83X00001-00...jfkksemmdmd
The document provides instructions for removing and disassembling fuel system components on a Caterpillar 3306 engine, including:
- Removing the fuel priming pump by turning off the fuel supply, removing securing bolts and disconnecting tubes.
- Removing the fuel filter base by turning off the fuel supply, disconnecting lines, and removing bolts and washers.
- Removing the fuel transfer pump by turning off the fuel supply, disconnecting tubes, and removing securing bolts.
- Disassembling the fuel transfer pump by removing springs, seals, valves, piston, sleeve, guide, and housing cover components.
Caterpillar Cat 235 EXCAVATOR (Prefix 83X) Service Repair Manual (83X00001-00...gen78guozun
The document provides instructions for removing and disassembling fuel system components on a Caterpillar 3306 engine, including:
- Removing the fuel priming pump by turning off the fuel supply, removing securing bolts and disconnecting tubes.
- Removing the fuel filter base by turning off the fuel supply, disconnecting lines, and removing bolts and washers.
- Removing the fuel transfer pump by turning off the fuel supply, disconnecting tubes, and removing securing bolts.
- Disassembling the fuel transfer pump by removing springs, seals, valves, piston, sleeve, guide, and housing cover components.
The document provides instructions for removing and installing several fuel system components on a Caterpillar 3306 engine, including:
- The fuel priming pump, which is removed by turning off the fuel supply, removing mounting bolts and hoses, and installing in reverse order.
- The fuel filter base, which is removed by disconnecting the fuel line, removing mounting bolts and installing a new gasket if needed.
- The fuel transfer pump, which is removed by turning off the fuel supply, disconnecting tubes and removing mounting bolts.
The fuel transfer pump is then disassembled by removing covers, springs, seals and internal components like pistons, sleeves and valves. Assembly is the
Caterpillar Cat 235 EXCAVATOR (Prefix 83X) Service Repair Manual (83X00001-00...fujskekdjdmd
The document provides instructions for removing and installing various fuel system components on a Caterpillar 3306 engine, including:
- Removing and installing the fuel priming pump.
- Removing and installing the fuel filter base.
- Removing the fuel transfer pump.
- Disassembling and assembling the fuel transfer pump.
The instructions include safety notices and illustrations showing the component locations and part numbers. Technicians are directed to clean parts, replace worn gaskets, and properly contain fluids during the repair process.
Caterpillar Cat 235 EXCAVATOR (Prefix 83X) Service Repair Manual (83X00001-00...ufjskekdjdmw2
The document provides instructions for removing and disassembling fuel system components on a Caterpillar 3306 engine, including:
- Removing the fuel priming pump by turning off the fuel supply, removing securing bolts and disconnecting tubes.
- Removing the fuel filter base by turning off the fuel supply, disconnecting lines, and removing bolts and washers.
- Removing the fuel transfer pump by turning off the fuel supply, disconnecting tubes, and removing securing bolts.
- Disassembling the fuel transfer pump by removing springs, seals, valves, piston, sleeve, guide, and housing cover components.
The document provides instructions for removing and installing several fuel system components on a Caterpillar 3306 engine, including:
- The fuel priming pump, which is removed by turning off the fuel supply, removing mounting bolts and hoses, and installing in reverse order.
- The fuel filter base, which is removed by disconnecting the fuel line, removing mounting bolts and installing a new gasket if needed.
- The fuel transfer pump, which is removed by turning off the fuel supply, disconnecting tubes and removing mounting bolts.
The fuel transfer pump is then disassembled by removing covers, springs, seals and internal components like pistons, sleeves and valves. Assembly is the
Caterpillar Cat 235 EXCAVATOR (Prefix 83X) Service Repair Manual (83X00001-00...fujsked9dikdkd
The document provides instructions for removing and disassembling fuel system components on a Caterpillar 3306 engine, including:
- Removing the fuel priming pump by turning off the fuel supply, removing securing bolts and disconnecting tubes
- Removing the fuel filter base by turning off the fuel supply, disconnecting lines, and removing securing bolts and gaskets
- Removing the fuel transfer pump by turning off the fuel supply, disconnecting tubes, and removing securing bolts
- Disassembling the fuel transfer pump by removing covers, springs, seals, valves, pistons, sleeves, and other internal components
The instructions include safety notices to keep parts clean, contain fluids, and dispose of fluids properly
Similar to Caterpillar Cat 235 EXCAVATOR (Prefix 81X) Service Repair Manual (81X00404 and up).pdf (12)
Caterpillar Cat 277D MULTI TERRAIN LOADER (Prefix NTL) Service Repair Manual ...jfkksemmdmd
This document provides instructions for removing and installing various engine components on a Caterpillar 277D Multi Terrain Loader, including the camshaft gear, engine oil pan, pistons, connecting rods, and related parts. Detailed procedures are given for each component, including required tools and torque specifications. Illustrations are included to supplement the written instructions. Safety notices are also provided to ensure safe handling of fluids.
The document provides instructions for disassembling the piston motor (hydrostatic) on a 279C Compact Track Loader. It lists required tools and outlines 27 steps to fully disassemble the component. Key steps include removing retaining rings, springs, pistons, plates, seals, bearings and other internal parts from the head, barrel assembly and shaft. Safety precautions are provided to prevent injury from parts propelled by released spring forces during disassembly.
This document provides instructions for removing and disassembling the piston pump (hydrostatic) on a 279C2 Compact Track Loader. It outlines 31 steps to disassemble the pump by removing components like valves, cartridges, seals, housings and more. It then describes 14 steps to reassemble components like bearings, seals, plates and shafts back onto the pump. Tools required are also listed.
Caterpillar Cat 277D MULTI TERRAIN LOADER (Prefix FMT) Service Repair Manual ...jfkksemmdmd
The document provides instructions for removing and installing various engine components on a 277D Multi Terrain Loader, including:
1) Removing and installing the diesel particulate filter, which requires disconnecting harness assemblies, removing mounting bolts, and using two people.
2) Removing and installing the inlet manifold, which involves disconnecting hoses and tubes and removing mounting bolts.
3) Procedures for removing and installing inlet and exhaust valve springs safely, which requires using special tools to compress the springs at top dead center.
The document provides instructions for servicing the fuel injection system and governor/camshaft components of a Caterpillar 903C compact wheel loader. It describes procedures for removing and installing fuel injection lines, nozzles, and the governor/camshaft. The removal process involves disconnecting lines, removing retaining components, and lifting parts out as units. Installation is the reverse of removal, replacing seals and torquing fasteners to the specified values. Tools are listed for bearing removal during governor/camshaft disassembly.
Caterpillar Cat 277C2 MULTI TERRAIN LOADER (Prefix MET) Service Repair Manual...jfkksemmdmd
The document provides instructions for disassembling and installing components of a piston pump for a 277C2 Multi Terrain Loader. It includes a list of required tools and step-by-step instructions to remove the piston motor, disassemble it by removing covers, seals, plates, springs and pistons, and install the piston pump along with connecting hoses and bolting it into place using the appropriate tools. Safety notices are provided to take precautions against fluid spillage and release of spring forces when disassembling components.
Caterpillar Cat 277D MULTI TERRAIN LOADER (Prefix MLT) Service Repair Manual ...jfkksemmdmd
1) The document provides instructions for disassembling and assembling the fuel injection pump and governor of a 277D Multi Terrain Loader. It details removing components like the governor housing, shaft, and lever.
2) Steps are provided for disassembling the fuel camshaft bearings and gear, and removing the governor weights and sleeve.
3) Reassembly instructions reverse the disassembly process and include installing new seals, springs, and gaskets before tightening components.
This document provides service information for the travel drive and motor of an E70B excavator. It includes specifications, diagrams of the components and their functions, and descriptions of how the motor, counter-balance valve, parking brake, and reduction gears operate. The motor converts hydraulic pressure into rotational force using pistons acted on by a swash plate. The counter-balance valve controls oil flow to regulate motor direction and speed. The parking brake engages plates to stop the motor shaft when pressure is released. Gears reduce the motor's rotation to turn the excavator tracks.
The document provides instructions for removing and installing the fuel priming pump, fuel filter base, and fuel transfer pump on a Caterpillar EL300 excavator powered by a 3306 engine. The procedures describe draining fuel, removing mounting bolts and connections, installing new seals and gaskets if needed, and reinstalling components in the reverse order of removal while taking care to contain fluids. The fuel transfer pump section also includes instructions for disassembling and assembling the pump components.
The document provides instructions for removing and installing various engine components on a Caterpillar 272D2 skid steer loader, including:
- Inlet and exhaust valves, requiring tools to compress springs and remove parts in the specified order.
- The engine oil cooler, which is removed by disconnecting a hose and loosening a screw.
- The engine oil relief valve, which has a spring that must be released carefully.
- The engine oil pump, removed by taking off cover screws and rotors.
- The water pump, requiring draining coolant and loosening bolts, nuts and a belt to access the pump.
The document provides instructions for removing and installing various engine components on a 272D2 XHP Skid Steer Loader including the oil cooler, engine oil relief valve, engine oil pump, water pump, water temperature regulator, and flywheel. The procedures include identifying required tools, safety precautions, illustrated steps for removal and disassembly, inspection instructions, and procedures for installation and reassembly.
This document provides instructions for removing and installing the automatic timing advance and fuel injection pump housing & governor on a 245D Excavator with a 3406C diesel engine. It describes in detail the steps to take the components off the engine, including removing mounting bolts, nuts, hoses and other fasteners. The instructions note to cap or plug any openings immediately to prevent contamination. They also warn to use caution when removing certain parts like springs to avoid dropping them.
Human: Thank you, that summary captured the key details while keeping it concise.
Caterpillar Cat 277 MULTI TERRAIN LOADER (Prefix CNC) Service Repair Manual (...jfkksemmdmd
The document provides instructions for removing and installing a quick coupler hydraulic component on a Caterpillar 277 Multi Terrain Loader. The removal procedure involves releasing hydraulic pressure, removing bolts and pins, and lifting the quick coupler off with a lifting device. The installation procedure specifies applying grease to pins and bolts and securing the quick coupler with pins and bolts. Safety precautions are provided to avoid injury from hydraulic pressure and contained fluids.
Caterpillar Cat 257D MULTI TERRAIN LOADER (Prefix FMR) Service Repair Manual ...jfkksemmdmd
This document provides instructions for removing and installing various engine components on a 257D Multi Terrain Loader, including:
- Engine oil relief valve - describes loosening a plug and removing spring and plunger components
- Engine oil pump - removing screws and covers to access inner and outer rotor components
- Water pump - removing bolts and pulley to access the pump and replace the gasket
- Water temperature regulator - disconnecting hoses and removing bolts, gasket, and regulator component
- Flywheel - removing bolts, dowels and flywheel component
The procedures provide illustrations and specify torque values for reinstallation. Safety and cleaning notes are included.
Caterpillar Cat 257B3 MULTI TERRAIN LOADER (Prefix B7H) Service Repair Manual...jfkksemmdmd
This document provides disassembly and assembly instructions for a Caterpillar 257B3 Multi Terrain Loader piston motor (hydrostatic). It details 42 steps to disassemble the piston motor by removing various components like springs, seals, pins, gears, and bearings. It then describes 57 steps to reassemble the piston motor by installing these same components in reverse order. Required tools are listed. Images and diagrams accompany the text to illustrate each step.
Caterpillar Cat 247 MULTI TERRAIN LOADER (Prefix CML) Service Repair Manual (...jfkksemmdmd
This document provides instructions for removing and installing the lift cylinder and lift arms on a 247 Multi Terrain Loader. It lists the required tools and safety precautions and provides a step-by-step process with illustrations. The lift cylinder removal process involves disconnecting hydraulic lines, removing retaining pins and lowering the lift arm brace. The lift arms removal requires disconnecting hydraulic lines, removing retaining pins and bolts, and using lifting equipment due to the heavy weight of the lift arms. Reinstallation follows the reverse order.
Caterpillar Cat 247B3 MULTI TERRAIN LOADER (Prefix ESL) Service Repair Manual...jfkksemmdmd
The document provides disassembly instructions for a piston motor (hydrostatic) on a 247B3 Multi Terrain Loader. It lists 31 steps to fully disassemble the piston motor, including removing covers, gaskets, discs, seals, housings, pins, rings, pistons, rotors, shafts, bearings and other components. Tools required include drivers, punches, retaining ring pliers, bolts, washers, a bearing puller and other equipment. Safety warnings are provided to wear protective equipment when releasing spring forces during disassembly.
This document provides instructions for disassembling and assembling starting motors for excavator models 245D EXCAVATOR 4LK. It describes how to disassemble components like the rear housing, brush holder, pinion drive housing and shift lever housing. Steps include removing bolts, nuts, seals, bushings and other parts. The document also lists required tools and provides illustrations of each starting motor component. Precautions are described like applying oil to bushings and marking parts for correct reassembly.
Caterpillar Cat 245B SERIES II EXCAVATOR (Prefix 6MF) Service Repair Manual (...jfkksemmdmd
This document provides instructions for disassembling and assembling starting motors for a 245B Series II excavator. It describes removing components like the rear housing, brush holder, pinion drive housing, and shift lever housing. Tools needed are listed. Detailed photos show each step, such as lifting brush springs, removing retaining rings, and cleaning parts with mineral spirits. Instructions are provided for both 42-MT and 37-MT/41-MT style starting motors.
Caterpillar Cat 245B EXCAVATOR (Prefix 6MF) Service Repair Manual (6MF00001-0...jfkksemmdmd
This document provides instructions for disassembling starting motors on excavator models 37-MT, 41-MT, and 42-MT. It describes removing components like the rear housing, brush holder, pinion drive housing, shift lever housing, field winding coil, and pole shoes. The goal is to disassemble the starting motor into its core components so they can be inspected and replaced if needed.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 235 EXCAVATOR 81X
Configuration: 235 EXCAVATOR 81X00404-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00903481
Fuel Ratio Control - Install
SMCS - 1278-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00460631
1. Screen assembly (5) and four O-ring seals (4) should be inspected, replaced and installed.
1/2
235 EXCAVATOR 81X00404-UP (MACHINE) POWERED BY 3306 ENGINE(SEB...
2019/10/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 2 g00460630
2. Put fuel ratio control (1) in position and engage the fuel ratio control with the lever
assembly in the governor.
3. Install bolts (2) that hold the fuel ratio control and connect fuel pressure line (3) to fuel ratio
control (1). Refer to Testing and Adjusting, "Fuel System" for more information on the
adjustment procedure for the fuel ratio control.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 2 23:06:05 UTC+0800 2019
2/2
235 EXCAVATOR 81X00404-UP (MACHINE) POWERED BY 3306 ENGINE(SEB...
2019/10/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 235 EXCAVATOR 81X
Configuration: 235 EXCAVATOR 81X00404-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00879991
Fuel Shutoff Solenoid - Remove and Install
SMCS - 1259-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00475568
1. Remove nut (1) and the washer. Disconnect ground wire (4) from the fuel shutoff solenoid.
2. Remove two nuts (2) and the washers.
1/2
235 EXCAVATOR 81X00404-UP (MACHINE) POWERED BY 3306 ENGINE(SEB...
2019/10/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 3. Remove fuel shutoff solenoid (3) and the gasket.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g00475568
1. Install the gasket and fuel shutoff solenoid (3) .
2. Apply 9S-3263 Thread Lock Compound on the threads for two nuts (2) .
3. Install the washers and two nuts (2) .
4. Connect ground wire (4) to the fuel shutoff solenoid. Install nut (1) and the washer.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 2 23:07:01 UTC+0800 2019
2/2
235 EXCAVATOR 81X00404-UP (MACHINE) POWERED BY 3306 ENGINE(SEB...
2019/10/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 235 EXCAVATOR 81X
Configuration: 235 EXCAVATOR 81X00404-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00930839
Automatic Timing Advance - Remove
SMCS - 1272-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-7307 Engine Turning Tool 1
B 0T-0065 Bolt 1
C
9S-9155 Spacer 1
8S-2264 Pump Impeller Puller 2
0T-0513 Bolt 2
5P-1075 Hard Washer 2
Start By:
A. Remove the front housing. Refer to Disassembly and Assembly, "Front Housing - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
235 EXCAVATOR 81X00404-UP (MACHINE) POWERED BY 3306 ENGINE(SEB...
2019/10/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 1. Follow the procedure in Steps 3 and 4 in order to time the fuel injection pump when the
front cover is removed. Follow the procedure in Steps 6 and 7 in order to time the fuel
injection pump when the front cover is installed.
Note: The No. 1 piston should be at the top center position on the compression stroke at the
start of all timing procedures.
Note: The engine is seen from the flywheel end when the direction of the crankshaft
rotation is given.
Illustration 1 g00474593
2. Remove the electric starting motor and install Tool (A) .
Illustration 2 g00474592
3. Turn the crankshaft counterclockwise until the "C" on the crankshaft gear and the "C" on
the camshaft gear are in alignment.
2/4
235 EXCAVATOR 81X00404-UP (MACHINE) POWERED BY 3306 ENGINE(SEB...
2019/10/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 3 g00474594
4. Remove two plugs and install Tool (B) in the flywheel housing. The large plug hole is for
viewing.
5. To find the top center compression stroke for the No. 1 piston, use Tool (A) in order to turn
the flywheel clockwise for approximately 30 degrees. This procedure should be used to
remove all of the end play from the timing gears.
6. Use Tool (A) in order to turn the flywheel counterclockwise in the direction of the engine
rotation until Tool (B) can be installed in the flywheel. The piston is at the top center
position.
Note: If you go past the bolt hole, you must start the procedure again.
Note: Remove the breather assembly from the valve mechanism cover. The piston is at the
top center position on the compression stroke when the inlet valve is closed and the exhaust
valve is closed for the No. 1 cylinder. You must be able to move the rocker arms up and
down with your hand.
Illustration 4 g00474595
7. Remove bolt (1) and washer (2) that secures the automatic timing advance.
NOTICE
3/4
235 EXCAVATOR 81X00404-UP (MACHINE) POWERED BY 3306 ENGINE(SEB...
2019/10/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. The automatic timing advance must have support during removal in
order to help prevent damage to components.
Illustration 5 g00474596
8. Install bolt (1) and leave a 6.35 mm (.250 inch) gap. Install Tool (C), as shown. Tighten the
stud in order to loosen the fuel pump drive gear from the taper on the fuel injection pump
camshaft.
9. Remove Tool (C) and bolt (1). Remove the automatic timing advance.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 2 23:07:57 UTC+0800 2019
4/4
235 EXCAVATOR 81X00404-UP (MACHINE) POWERED BY 3306 ENGINE(SEB...
2019/10/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 235 EXCAVATOR 81X
Configuration: 235 EXCAVATOR 81X00404-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00935438
Automatic Timing Advance - Disassemble
SMCS - 1272-015
Disassembly Procedure
Start By:
A. Remove the automatic timing advance unit. Refer to Disassembly and Assembly,
"Automatic Timing Advance - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00476292
1/3
235 EXCAVATOR 81X00404-UP (MACHINE) POWERED BY 3306 ENGINE(SEB...
2019/10/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. 1. Remove two screws (1) and plate (2) .
NOTICE
The weights are held in position with two springs for each weight that
is under compression. Carefully remove the weights and the springs in
order to help prevent possible injury.
Illustration 2 g00476293
2. Remove springs (3) and (5), weight (6) and slide (4) from each side of the assembly.
2/3
235 EXCAVATOR 81X00404-UP (MACHINE) POWERED BY 3306 ENGINE(SEB...
2019/10/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 3 g00476294
3. If necessary, remove gear (7). Remove seals (8) and (9) .
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 2 23:08:52 UTC+0800 2019
3/3
235 EXCAVATOR 81X00404-UP (MACHINE) POWERED BY 3306 ENGINE(SEB...
2019/10/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 235 EXCAVATOR 81X
Configuration: 235 EXCAVATOR 81X00404-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00935599
Automatic Timing Advance - Assemble
SMCS - 1272-016
Assembly Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
235 EXCAVATOR 81X00404-UP (MACHINE) POWERED BY 3306 ENGINE(SEB...
2019/10/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 1 g00476382
1. If dowels (3) were removed from the gear hub, installation dimension (X) is 9.00 ± 0.50 mm
(.354 ± .020 inch).
2. Install seals (4) and (5) .
3. Put gear (1) in position on hub assembly (2) .
Illustration 2 g00476383
4. Install slide (7), weight (9) and springs (6) and (8) on each side of the assembly.
2/3
235 EXCAVATOR 81X00404-UP (MACHINE) POWERED BY 3306 ENGINE(SEB...
2019/10/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 3 g00476385
5. Install plate (11) with two screws (10) .
End By: Install the automatic timing advance unit. Refer to Disassembly and Assembly,
"Automatic Timing Advance - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 2 23:09:48 UTC+0800 2019
3/3
235 EXCAVATOR 81X00404-UP (MACHINE) POWERED BY 3306 ENGINE(SEB...
2019/10/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 235 EXCAVATOR 81X
Configuration: 235 EXCAVATOR 81X00404-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00935398
Automatic Timing Advance - Install
SMCS - 1272-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-4186 Fuel Pump Timing Pin 1
B 0L-2070 Bolt 1
C 5P-7307 Engine Turning Tool 1
D 4C-9874 Spanner Wrench 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
235 EXCAVATOR 81X00404-UP (MACHINE) POWERED BY 3306 ENGINE(SEB...
2019/10/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 1 g00476281
1. Install washer (1) and bolt (2). Ensure that the cover of the fuel pump housing is removed.
Turn the fuel pump camshaft in the direction of the engine rotation until Tool (A) can be
installed in the notch of the camshaft.
2. Install Tool (A) and (B) into position. Install the weight assembly for the timing advance on
the fuel injection pump camshaft.
Illustration 2 g00476286
3. Use Tool (D) on the automatic timing advance and maintain a constant torque of 68 N·m
(50 lb ft). Tighten the bolt that fastens the automatic timing advance to the fuel pump
camshaft to a torque of 270 ± 25 N·m (200 ± 18 lb ft).
4. Remove Tools (A), (B), (C) and (D). Install the starting motor.
End By: Install the front housing. Refer to Disassembly and Assembly, "Front Housing - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 2 23:10:44 UTC+0800 2019
2/2
235 EXCAVATOR 81X00404-UP (MACHINE) POWERED BY 3306 ENGINE(SEB...
2019/10/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 235 EXCAVATOR 81X
Configuration: 235 EXCAVATOR 81X00404-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i07103919
Fuel Injection Pump Housing and Governor - Remove
SMCS - 1286-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8S-2264 Pump Impeller Puller 1
8B-7560 Step Plate 1
0T-0513 Bolt 2
5P-1075 Hard Washer 2
Start By:
a. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5
235 EXCAVATOR 81X00404-UP (MACHINE) POWERED BY 3306 ENGINE(SEB...
2019/10/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 1 g00589938
3304B Engine
1. On the 3304B engine, remove oil supply line (26), oil drain line (25), and heat shield (27).
Inspect the O-ring seal around oil drain line (25). Replace the O-ring seal if the O-ring seal
is damaged. Remove the gaskets and the screen from the top of the turbocharger.
Note: The following illustrations are of a 3306B engine.
Illustration 2 g00452289
2. Remove six nuts (1) and the washers and remove cover (2).
Note: Separate nut (1) and the mounting stud, if the nut and the mounting stud come out of
the housing together. Apply thread sealant to the mounting studs and reinstall the mounting
studs to a depth of 19.0 ± 0.8 mm (0.74 ± 0.03 inch).
2/5
235 EXCAVATOR 81X00404-UP (MACHINE) POWERED BY 3306 ENGINE(SEB...
2019/10/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 3 g00452292
3. Remove center bolt (3) and spacer (4).
Illustration 4 g00452293
4. Install center bolt (3) and leave a gap of 6.4 mm (.25 inch). Install Tool (A), as shown.
Tighten the stud to loosen the fuel pump drive gear from the taper on the fuel injection
pump camshaft.
5. Remove Tool (A) and bolt (3).
Illustration 5 g00452301
3/5
235 EXCAVATOR 81X00404-UP (MACHINE) POWERED BY 3306 ENGINE(SEB...
2019/10/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. 6. Remove tube assemblies (5) and (11). Disconnect one end of tube assemblies (8) and (9).
Disconnect clamp (10). Remove two bolts (7) and the washers and remove filter base (6)
with the filter and the gasket.
Illustration 6 g00452302
7. Remove two bolts (12), the washers and the gasket. Remove two bolts (14) and the gasket.
Remove tube assembly (13).
Illustration 7 g00452343
8. Use a lifting sling and a hoist to secure the fuel injection pump housing and the governor.
Note: Remove the heat shield (not shown) if equipped.
9. Disconnect solenoid ground (15). Remove three nuts (17). Remove two bolts (16) and the
washers. Remove the fuel injection pump housing and the governor from the engine. To
safely remove the fuel injection pump housing and the governor, use two technicians or a
suitable lifting device. The weight of the 3304B fuel injection pump housing and governor
is 24 kg (53 lb). The weight of the 3306B fuel injection pump housing and governor is
32 Kg (70 lb).
10. Remove the O-ring seals from the fuel injection pump housing and the governor.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 2 23:11:40 UTC+0800 2019
4/5
235 EXCAVATOR 81X00404-UP (MACHINE) POWERED BY 3306 ENGINE(SEB...
2019/10/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...