This document provides assembly instructions for a transmission in a 140M 2 motor grader. It lists required tools and parts and provides step-by-step instructions with accompanying illustrations. Some key steps include installing bearings and seals, assembling clutch components like plates and discs, and using lifting devices to position heavy transmission components. Cleanliness is emphasized throughout assembly.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
What Does the Active Steering Malfunction Warning Mean for Your BMWTanner Motors
Discover the reasons why your BMW’s Active Steering malfunction warning might come on. From electrical glitches to mechanical failures and software anomalies, addressing these promptly with professional inspection and maintenance ensures continued safety and performance on the road, maintaining the integrity of your driving experience.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
2. Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 140M 2 MOTOR GRADER M9D
Configuration: 140M Series 2 Motor Grader M9D00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
12M Series 2, 140M Series 2 and 160M Series 2 Motor Graders Power Train
Media Number -KENR8899-03 Publication Date -01/05/2017 Date Updated -18/05/2017
i06933343
Transmission - Assemble
SMCS - 3002-016; 3030-016; 3159-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 3
B 422-8733 Jack Stand Gp 3
C 1U-9202 Lever Puller Hoist 1
D 1P-1863 Retaining Ring Pliers 1
E 308-3470 Jack Stand Gp 2
F 140-7742 Sleeve 1
H FT-2769 Table 1
J 4C-8156 Lifting Fixture 1
L
9U-7480 Compressing Tube 1
8T-4133 Nut 1
8T-4224 Hard Washer 1
-
Threaded Rod
M10 - 1.5 by 460mm
1
N 2P-8312 Retaining Ring Pliers 1
R 189-0408 Shackle As 1
1/44
140M Series 2 Motor Grader M9D00001-UP (MACHINE) POWERED BY C9.3 Engi...
2020/1/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. 3E-3882 Eyebolt 1
T 4C-4030 Loctite 242 Thread Locker 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning
fluid. Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be
deposited on the parts which may cause trouble. Inspect all parts. If any parts are worn or
damaged, use new parts for replacement. Dirt and other contaminants can damage the precision
component. Perform assembly procedures on a clean work surface. Keep components covered and
protected always.
Note: Lubricate all seal rings and O-ring seals prior to assembly.
Note: Check the O-ring seals, and the seals for wear or for damage. Replace the components, if
necessary.
Note: Remove old anaerobic sealant from the bottom of the blind tapped holes in housing (237)
before assembling.
Illustration 1 g01389210
This Illustration is viewed from the bottom.
1. Install filter (246) and O-ring seal (245). Position cover (244) and install bolts (243).
Tighten bolts (243) to a torque of 28 ± 7 N·m (21 ± 5 lb ft).
2/44
140M Series 2 Motor Grader M9D00001-UP (MACHINE) POWERED BY C9.3 Engi...
2020/1/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 2 g01389019
2. Position plate (241) and install bolts (242). Tighten bolts (242) to a torque of 12 ± 3 N·m
(106 ± 27 lb in).
3. Lower the temperature of bearing outer races (240), (239), and (238). Install bearing outer
races (240), (239), and (238) into housing (237).
Illustration 3 g01389010
4. Install the O-ring seals and covers (236) onto housing (49). Tighten the bolts for covers
(236) to a torque of 28 ± 7 N·m (21 ± 5 lb ft). Install the O-ring seals and covers (235) onto
housing (49). Tighten the bolts for covers (235) to a torque of 28 ± 7 N·m (21 ± 5 lb ft).
3/44
140M Series 2 Motor Grader M9D00001-UP (MACHINE) POWERED BY C9.3 Engi...
2020/1/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 4 g01394193
5. Lower the temperature of races (234) and races (233) . Install races (234) and races (233)
into housing (49).
Illustration 5 g01394189
6. Install O-ring seal (232).
4/44
140M Series 2 Motor Grader M9D00001-UP (MACHINE) POWERED BY C9.3 Engi...
2020/1/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 6 g01394188
7. Raise the temperature of bearing (231). Install bearing (231). Install retaining ring (230).
Illustration 7 g01394185
8. Install gear (229).
9. Install retaining ring (228).
Illustration 8 g01394184
10. Install retainer (227). Install bearing (226). Install retaining ring (225).
5/44
140M Series 2 Motor Grader M9D00001-UP (MACHINE) POWERED BY C9.3 Engi...
2020/1/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 9 g01394180
11. Install gear (224). Install bolts (223). Tighten bolts (223) to a torque of 28 ± 7 N·m
(21 ± 5 lb ft).
Illustration 10 g01394236
12. Use two people to position shaft assembly (130) onto Tooling (H). The weight of input shaft
assembly (130) is approximately 25 kg (55 lb). Use suitable blocking to support input shaft
assembly (130). Install retaining ring (222) (not shown) onto input shaft assembly (130).
Install gear (221). Raise the temperature of inner bearing (220). Install inner bearing (220)
onto input shaft assembly (130).
Illustration 11 g01394368
13. Use a suitable lifting device to position input shaft assembly (130) to housing (237). The
weight of input shaft assembly (130) is approximately 23 kg (50 lb). Use Tooling (N) to
install retaining ring (219) onto input shaft assembly (130). Install ring seal (218).
6/44
140M Series 2 Motor Grader M9D00001-UP (MACHINE) POWERED BY C9.3 Engi...
2020/1/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 12 g01388797
Illustration 13 g01394379
14. Install seal rings (217) and (216) onto piston (215).
Illustration 14 g01388786
15. Install piston (215) and valve assembly (214) onto clutch assembly (174).
7/44
140M Series 2 Motor Grader M9D00001-UP (MACHINE) POWERED BY C9.3 Engi...
2020/1/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 15 g01388754
16. Install friction discs (213) and clutch plates (212) onto clutch assembly (174). Install friction
disc (211), spring (210), and hub assembly (207) onto clutch assembly (174).
Illustration 16 g01388732
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
17. Use Tooling (L) to compress hub assembly (207). Install two half rings (209) (not shown)
and lock rings (208) onto clutch assembly (174).
8/44
140M Series 2 Motor Grader M9D00001-UP (MACHINE) POWERED BY C9.3 Engi...
2020/1/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 17 g01388726
18. Position washer (205) to clutch assembly (174). Apply Tooling (T) to screws (206). Install
screws (206). Tighten screws (206) to a torque of 12 ± 3 N·m (106 ± 27 lb in).
Illustration 18 g01388685
19. Install thrust disc (204) and roller bearing assembly (203) onto clutch assembly (174).
Illustration 19 g01388678
20. Install gear assembly (202), thrust disc (201), thrust disc (200), and thrust race (199) onto
clutch assembly (174). Raise the temperature of inner bearing (198). Install inner bearing
(198) onto clutch assembly (174).
9/44
140M Series 2 Motor Grader M9D00001-UP (MACHINE) POWERED BY C9.3 Engi...
2020/1/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. 21. Use a suitable lifting device to turn over clutch assembly (174) onto Tooling (H). The
weight of clutch assembly (174) is approximately 43 kg (95 lb).
Illustration 20 g01388663
Illustration 21 g01394424
22. Install seal rings (196) and (197) onto piston (195).
Illustration 22 g01388653
23. Install piston (195) and valve assembly (194) onto clutch assembly (174).
10/44
140M Series 2 Motor Grader M9D00001-UP (MACHINE) POWERED BY C9.3 En...
2020/1/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 23 g01388635
24. Install friction discs (191), clutch plates (192), friction discs (193), spring (190), and hub
assembly (187) onto clutch assembly (174).
Illustration 24 g01388624
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
25. Use Tooling (L) to compress hub assembly (187). Install two half rings (189) (not shown)
and lock rings (188).
11/44
140M Series 2 Motor Grader M9D00001-UP (MACHINE) POWERED BY C9.3 En...
2020/1/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 25 g01388618
26. Position washer (185) to clutch assembly (174). Apply Tooling (T) to screws (186). Install
screws (186). Tighten screws (186) to a torque of 12 ± 3 N·m (106 ± 27 lb in).
Illustration 26 g01388614
27. Install thrust disc (184) and roller bearing assembly (183) onto clutch assembly (174).
Illustration 27 g01388597
28. Install gear assembly (182), thrust disc (181), and thrust disc (180) onto clutch assembly
(174). Raise the temperature of inner bearing (179). Install inner bearing (179) onto clutch
assembly (174).
12/44
140M Series 2 Motor Grader M9D00001-UP (MACHINE) POWERED BY C9.3 En...
2020/1/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 28 g01394545
29. Attach Tooling (R) and a suitable lifting device to clutch assembly (174). The weight of
clutch assembly (174) is approximately 64 kg (140 lb). Use Tooling (R) and the suitable
lifting device to install clutch assembly (174) to housing (237).
Illustration 29 g01388581
30. Install O-ring seals (177) and seal rings (178) onto seal carrier (176).
Illustration 30 g01388568
31. Position seal carrier (176) onto clutch assembly (174). Install bolts (175). Tighten bolts
(175) to a torque of 55 ± 10 N·m (41 ± 7 lb ft).
13/44
140M Series 2 Motor Grader M9D00001-UP (MACHINE) POWERED BY C9.3 En...
2020/1/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 31 g01388470
Illustration 32 g01394550
32. Install seal rings (173) and (172) onto piston (171).
Illustration 33 g01388335
33. Install piston (171) and valve assembly (170) onto clutch assembly (135).
14/44
140M Series 2 Motor Grader M9D00001-UP (MACHINE) POWERED BY C9.3 En...
2020/1/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 34 g01388330
34. Install friction discs (169), clutch plates (168), friction disc (167), spring (166), and hub
assembly (163) onto clutch assembly (135).
Illustration 35 g01388324
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
35. Use Tooling (L) to compress hub assembly (163). Install two half rings (165) (not shown)
and lock rings (164).
15/44
140M Series 2 Motor Grader M9D00001-UP (MACHINE) POWERED BY C9.3 En...
2020/1/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 36 g01388320
36. Position washer (162) to clutch assembly (135). Apply Tooling (T) to screws (161). Tighten
screws (161) to a torque of 12 ± 3 N·m (106 ± 27 lb in).
Illustration 37 g01388296
37. Install thrust disc (160) and roller bearing (159) onto clutch assembly (135).
Illustration 38 g01388277
38. Install gear assembly (158). thrust disc (157), thrust disc (156), and thrust race (155) onto
clutch assembly (135). Raise the temperature of inner bearing (154). Install inner bearing
(154) onto clutch assembly (135).
16/44
140M Series 2 Motor Grader M9D00001-UP (MACHINE) POWERED BY C9.3 En...
2020/1/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
20. 39. Use a suitable lifting device to turn over clutch assembly (135) onto Tooling (H). The
weight of clutch assembly (135) is approximately 41 kg (90 lb).
Illustration 39 g01388246
Illustration 40 g01394572
40. Install seal rings (153) and (152) onto piston (151).
Illustration 41 g01394574
41. Install piston (151) and wave spring (150) onto clutch assembly (135).
17/44
140M Series 2 Motor Grader M9D00001-UP (MACHINE) POWERED BY C9.3 En...
2020/1/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 42 g01388240
42. Install clutch plates (149), friction discs (148), and hub assembly (145).
Illustration 43 g01388208
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
43. Use Tooling (L) to compress hub assembly (145). Install two half rings (147) (not shown)
and lock rings (146).
18/44
140M Series 2 Motor Grader M9D00001-UP (MACHINE) POWERED BY C9.3 En...
2020/1/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 44 g01388185
44. Lower the temperature of bearing (144). Install bearing (144) into gear assembly (141).
Illustration 45 g01388168
45. Install washer (143), thrust disc (142), gear assembly (141), thrust disc (140), and spacer
(139) onto clutch assembly (135).
19/44
140M Series 2 Motor Grader M9D00001-UP (MACHINE) POWERED BY C9.3 En...
2020/1/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 46 g01394607
46. Install gear (138) and spacer (137) onto clutch assembly (135). Raise the temperature of
inner bearing (136). Install inner bearing (136).
Illustration 47 g01394616
47. Attach Tooling (R) and a suitable lifting device to clutch assembly (135). The weight of
clutch assembly (135) is approximately 61 kg (135 lb). Use Tooling (R) and the suitable
lifting device to install clutch assembly (135) into housing (237).
Illustration 48 g01394625
48. Install O-ring seals (134) and seal rings (133) onto seal carrier (132).
20/44
140M Series 2 Motor Grader M9D00001-UP (MACHINE) POWERED BY C9.3 En...
2020/1/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...