Cunico manufactures high quality Cartridge Valves for Submarine, Aircraft and Carrier Rocket Launcher. Valve Cartridges are Interchangeable within each Valve Body.
Systematic Review of JSATS Passage and Survival Data at Bonneville and The Da...Bishes Rayamajhi
Systematic Review of JSATS
Passage and Survival Data at
Bonneville and The Dalles Dams
during Alternate Turbine and
Spillbay Operations from 2008-
2012
NLC is a single-circuit or dual-circuit chiller charged with R410a gas. It has directly coupled plug fans with an EC inverter motor to ensure the quietest possible machine operation, scroll compressors with a high yield and low electricity absorption, a plate heat exchanger and a copper/aluminium coil. The machine cools water to supply the distribution system that is usually connected to fan coil type terminals. In addition, NLC can also produce domestic hot water if it is fitted with a desuperheater or total recovery system, so it's ideal for residential and commercial contexts. It can be equipped with a hydronic kit (system side) including an expansion tank, safety valve (water side) and drain valve.
Systematic Review of JSATS Passage and Survival Data at Bonneville and The Da...Bishes Rayamajhi
Systematic Review of JSATS
Passage and Survival Data at
Bonneville and The Dalles Dams
during Alternate Turbine and
Spillbay Operations from 2008-
2012
NLC is a single-circuit or dual-circuit chiller charged with R410a gas. It has directly coupled plug fans with an EC inverter motor to ensure the quietest possible machine operation, scroll compressors with a high yield and low electricity absorption, a plate heat exchanger and a copper/aluminium coil. The machine cools water to supply the distribution system that is usually connected to fan coil type terminals. In addition, NLC can also produce domestic hot water if it is fitted with a desuperheater or total recovery system, so it's ideal for residential and commercial contexts. It can be equipped with a hydronic kit (system side) including an expansion tank, safety valve (water side) and drain valve.
Alfa Labal - Pump Handbook
The handbook includes all the necessary information for the correct selection and successful application of the Alfa Laval ranges of Centrifugal,Liquid Ring and Rotary Lobe Pumps.
Service Solahart Jakarta Barat Pemanas Air Solar Water Heater Tenaga Matahari Solahart ahli
Dalam rangka untuk memastikan layanan terbaik dan saran, Solahart pemanas air tenaga surya dan sistem tenaga surya hanya tersedia melalui Expert Solahart lokal Anda. Dan dengan cakupan seluruh Australia ada satu tidak jauh dari Anda. Cari ahli terdekat Anda di sini.
Semua ahli kami dilatih dan memenuhi syarat untuk menilai rumah Anda atau bisnis dan penggunaan energi Anda. Konsultasi surya GRATIS kami menjamin Anda mendapatkan solusi terbaik mutlak surya untuk situasi Anda. Buku gratis di rumah surya kutipan di sini.
Tidak hanya installer sistem tenaga surya kita diakreditasi oleh Dewan Energi Bersih, mereka juga dilatih oleh Solahart untuk memastikan bahwa setiap instalasi dilakukan sesuai dengan standar instalasi kami yang ketat dan hanya komponen yang ditentukan oleh Solahart digunakan untuk memastikan kinerja dan keamanan sistem tenaga surya Solahart Anda.
Alfa Labal - Pump Handbook
The handbook includes all the necessary information for the correct selection and successful application of the Alfa Laval ranges of Centrifugal,Liquid Ring and Rotary Lobe Pumps.
Service Solahart Jakarta Barat Pemanas Air Solar Water Heater Tenaga Matahari Solahart ahli
Dalam rangka untuk memastikan layanan terbaik dan saran, Solahart pemanas air tenaga surya dan sistem tenaga surya hanya tersedia melalui Expert Solahart lokal Anda. Dan dengan cakupan seluruh Australia ada satu tidak jauh dari Anda. Cari ahli terdekat Anda di sini.
Semua ahli kami dilatih dan memenuhi syarat untuk menilai rumah Anda atau bisnis dan penggunaan energi Anda. Konsultasi surya GRATIS kami menjamin Anda mendapatkan solusi terbaik mutlak surya untuk situasi Anda. Buku gratis di rumah surya kutipan di sini.
Tidak hanya installer sistem tenaga surya kita diakreditasi oleh Dewan Energi Bersih, mereka juga dilatih oleh Solahart untuk memastikan bahwa setiap instalasi dilakukan sesuai dengan standar instalasi kami yang ketat dan hanya komponen yang ditentukan oleh Solahart digunakan untuk memastikan kinerja dan keamanan sistem tenaga surya Solahart Anda.
MATHEMATICS BRIDGE COURSE (TEN DAYS PLANNER) (FOR CLASS XI STUDENTS GOING TO ...PinkySharma900491
Class khatm kaam kaam karne kk kabhi uske kk innings evening karni nnod ennu Tak add djdhejs a Nissan s isme sniff kaam GCC bagg GB g ghan HD smart karmathtaa Niven ken many bhej kaam karne Nissan kaam kaam Karo kaam lal mam cell pal xoxo
Building a Raspberry Pi Robot with Dot NET 8, Blazor and SignalR - Slides Onl...Peter Gallagher
In this session delivered at Leeds IoT, I talk about how you can control a 3D printed Robot Arm with a Raspberry Pi, .NET 8, Blazor and SignalR.
I also show how you can use a Unity app on an Meta Quest 3 to control the arm VR too.
You can find the GitHub repo and workshop instructions here;
https://bit.ly/dotnetrobotgithub
1. 801 Stop Valve 802 Check (Non-Return)
Valve
803-Screw Down Non-Return
Valve
806 Actuated Stop Valve
Normally Closed
807 Actuated Stop Valve
Normally Open
813 Relief Valve 814 Filter
818 Pressure Reducer
828 Back Pressure
Regulator (Spring Loaded)
CARTRIDGE VALVES
Different Valve Cartridges (Interchangeable within each Valve Body)
817 Dome Pressure
Regulator
810 Flushing Adapter
www.dynamiccontrols.co.uk www.cunicocorp.com
Sizes
Valve
Body Size Est. Weight Pipe Size Cv
A2 3Kg/6.6lbs NB15 – ½” 6
B3 6Kg/13.2lbs NB20 – ¾” 18
C4 15Kg/33lbs NB25 – 1” 36
D5 39Kg/87lbs NB32 – 1 ¼” 55
E6 63Kg/138lbs NB40 1 ½” 140
G7 98Kg/216lbs NB50 – 2” 250
H8 101Kg/232lbs NB65 – 2 ½” 250
J9 101Kg/232lbs NB80 – 3” 250
821 Electrically
Actuated Valve
Advantages
Reduce Construction & Life-cycle Costs
• Body is integral part of platform for lifetime.
• Cartridge can be replaced, in-line, within minutes,
• Valve seat is part of removable cartridge
• Twelve different cartbody size.
• Reduction in spares/inventory…not necessary to
inventory valve body's….
ridges (interchangeable) within each valve • End
connections-butt weld/socket weld/screwed.
SUBMARINE-AIRCRAFT CARRIER-ROCKET LAUNCH
Forged valve body
12
Materials: 70/30 CuNi, Stainless Steel, Monel
Working Pressure
• Operating Pressure:
280 Bar/4000 psi
• 400 Bar/6000 psi
1 2 3 4 5
6
7
8 9
10 11 12
1 of 27
MARKETS
Cartridge Valve
Forged Body
Rev 7/31/14
2. “APPLICATIONS”
Rev. 7/31/14
CARTRIDGE VALVES
SUBMARINE-AIRCRAFT CARRIER-ROCKET LAUNCH
“Submarine Systems, Nuclear and Diesel Electric, where the full Range of Cartridge valves are fitted”
AIR
AVBS = Aux Vent & Blow System
BIB = Built in Breathing System & Hood Inflation System
DDS = Diesel Air Start System
EBA = Emergency Air Breathing System
FAS = Firing Air Systems
HPA = High Pressure Air System
HPB = High Pressure Blow System
MLO = Main Lub Oil System
WHA = Weapons Handling System
DQA = Divers Quality Breathing Air System
CO2
CDR = Carbon Dioxide Removal System
HYDROGEN
LPE = Electrolyser System
METHANOL
GM = Gas Mgmt Plant System
NITROGEN
HPDHR System
N = Nitrogen System
PC = Primary Circuit
OPG = Valve OP & Gas System
WM = Water Mist System
WATER
E = Emergency Core Cooling System
FT = Feed Transfer System
H&C = Hot & Cold Domestic System
PCD = Primary Coolant Discharge System
PCM = Primary Coolant Make-up System
PCS = Primary Coolant Sampling System
PSW = Primary Shield Water System
RCFW = RCFW Cooling System
EBS = Emergency Blow System
OIL
EHP = External Hydraulic Power Plant
EHS = External Hydraulics Systems
HTS = Hydraulic Oil Fill & Transfer System
HDS = Hydroplane & Steering Control System
HHP = Hydroplane & Steering Gear
Hydraulic Power Plant
MHP = Main Hydraulic Power Plant
HS = Main Hydraulic System
SP = Secondary Propulsion System
WH = Weapons Handling System
HFI = Hydraulic Fire Isolation
www.dynamiccontrols.co.uk www.cunicocorp.com
2 of 27
3. NO. OF VALVES PER TOTAL NO. DATE OF
SUBMARINES/SHIPS SUBMARINE VALVES COMMISSION
CARTRIDGE VALVE POPULATION
U.K.
U.S.A.
• SWIFTSURE- SSN
• VANGUARD - SSBN
• TRAFALGAR- SSN
• ASTUTE- SSN
• SEAWOLF- SSN
• VIRGINIA- SSN
1st Commissioned: 1973
1st Commissioned: 1993
1st Commissioned: 1985
1st Commissioned: 2010
5 Boats Confirmed
1st Commissioned: 1997
1st Commissioned: 2004
18 Boats Confirmed
5 980 4,900
4 2,067 8,268
7 1,750 12,250
5 1,860 9,310
3 4 12
18 4 72
CANADA • VICTORIA- SS
4 1,260 5,040
formerly Upholder (UK):
1st Commissioned: 1986
Victoria (Canada) Commissioned: 2000
SPAIN • S-80 CLASS- SS
4 580 1st to be Commissioned 2013
FRANCE • BARRACUDA- SSN
4 1,250 1st to be Commissioned : Expected in 2017
INSTALLED BASE
3 of 27
4. INDIA • ROCKET LAUNCH
• OFFSHORE PATROL VESSEL
NETHERLANDS
SPAIN
• M-CLASS FRIGATES
• PROJECT 17
• AIRCRAFT CARRIER
1st Commissioned : 1991
1st Commissioned : 2010
1st to be Commissioned:
Expected in 2014
1st Commissioned : 2009
7 925 6,475
1 360
3 486 1,458
8 95 760
INDIA
1 1,842
NO. OF VALVES PER TOTAL NO. DATE OF
SUBMARINES/SHIPS SUBMARINE VALVES COMMISSION
INSTALLED BASE
• OHIO REPLACEMNT
PROGRAM(ORP)—SSBN
U.S.A.
Future Request “To be Determined”
• OHIO REPLACEMNT
PROGRAM(ORP)—SSBN
Future Request “To be Determined”
U.K.
4 of 27
5. • AIRCRAFT CARRIER-CVN 78
1st to be
Commissioned:
Expected in 2015
1 680
NO. OF VALVES PER TOTAL NO. DATE OF
SUBMARINES/SHIPS SUBMARINE VALVES COMMISSIONINSTALLED BASE
U.S.A.
• AIRCRAFT CARRIER-CVN 79
1 680
5 of 27
No. of
Submarines/Ships
Total No. of Valves
• Submarines 54 41,682
• Aircraft Carriers/
Naval Surface Ships
21 10,413
• Rocket Launch 1 1,842
TOTAL INSTALLED BASE
TOTAL 76 53,937
Rev. 7/31/14
6.
VALVE TECHNICAL DATA SHEET
STOP VALVE 801
280 Bar 4000 psi
Technical Data
Design Specification Based on NES 375/ MIL-V-24109
Working Pressure 280 Bar / 4000 psi
Working Temperature Min –20ºC/-4ºF Max 120ºC/250ºF
Medium Air, Nitrogen, Helium, Oxygen. Hydraulic Fluid.
Quality Assurance Level En 10204, 3.1b also Full traceability – MIC Level 1
Cleaning TP102, Oxygen cleaning to MIL-STD-1330
Hydrostatic Test 420 Bar / 6000psi (High pressure and low pressure sides)
Airtight Test 308 Bar/ 3400psi
Shock Qualification MIL-S-901D
Vibration Qualification MIL-STD-167-1
Leakage Class Bubble Tight as per ANSI Class VI
Housing Material 70/30 Copper Nickel to NES 780 Pt2, class 1/ASTM B151
Main Cartridge Components Material Nickel aluminium bronze to NES 833 part 2 /ASTM B150
Seals Material HNBR/ Fluorocarbon
Seat Material PEEK virgin FL350
Nuts/Studs Material Stainless Steel NES 862/ASME 194/ASME 193 MIL-S-1222
Handwheel Material Aluminium/Stainless Steel
Connection Type Cartridge flanged to housing or manifold.
Housing welded or screwed (to be specified)
OVERALL DIMENSIONS (CARTRIDGE AND HOUSING)
Product
Designation
Estimated
Weight
Pipe Size
Cv
A
(mm/ins)
B
(mm/ins)
C
(mm/ins)
D
(mm/ins)
H
(mm/ins)
L
(mm/ins)
801-A2 2Kg/4.4lbs NB15/½” 6 75/2.95 28/1.1 125/4.9 64/2.5 97/3.8 215/8.46
801-B3 4Kg/8.8lbs NB20/¾” 18 95/3.7 29/1.14 145/5.71 86/3.39 16/0.63 228/8.98
801-C4 10Kg/22lbs NB25/1” 36 105/4.1 39/1.54 190/7.48 112/4.41 155/6.1 254/10.0
801-D5 26Kg/58lbs NB32/1¼” 55 115/4.5 44/1.73 250/9.84 137/5.39 180/7.09 280/11.0
801-E6 42Kg/92lbs NB40/1½” 140 180/7.1 50/1.97 285/11.22 175/6.89 230/9.06 304/12.0
801-G7 65Kg/143lbs NB50/2” 250 148/5.83 122/4.8 420/16.54 275/10.83 368/14.49 368/14.5
801-H8 65Kg/143lbs NB75/2.5” 250 148/5.83 122/4.8 420/16.54 275/10.83 368/14.49 368/14.5
PRODUCT OPTIONS
Stainless Steel bodies and cartridges for a wider range of
fluids such as Water, Steam, Oxygen, & Nitric Acid
Additional leak testing for valves to be used with Helium
Limit switches for confirmation of operation
Stainless Steel cartridges in manifolds for 280 bar systems Viton seals for operation at higher temperatures
sales@dynamiccontrols.co.uk T: +44 (0) 161 633 3933 sales@cunicocorp.com T: 562 733 4633
Rev. 7/31/14
6 of 27
7.
VALVE TECHNICAL DATA SHEET
STOP VALVE 801
400 Bar 6000 psi
Technical Data
Design Specification Based on NES 375/ MIL-V-24109
Working Pressure 400 Bar / 6000 psi
Working Temperature Min –20ºC/-4ºF Max 120ºC/250ºF
Medium Air, Nitrogen, Helium, Oxygen. Hydraulic Fluid.
Quality Assurance Level En 10204, 3.1b also Full traceability – MIC Level 1
Cleaning TP102, Oxygen cleaning to MIL-STD-1330
Hydrostatic Test 600 Bar / 9000psi (High pressure and low pressure sides)
Airtight Test 440 Bar/ 6600psi
Shock Qualification MIL-S-901D
Vibration Qualification MIL-STD-167-1
Leakage Class Bubble Tight as per ANSI Class VI
Housing Material 70/30 Copper Nickel to NES 780 Pt2, class 1/ASTM B151
Main Cartridge Components Material Nickel aluminium bronze to NES 833 part 2 /ASTM B150
Seals Material HNBR/ Fluorocarbon
Seat Material PEEK virgin FL350
Nuts/Studs Material Stainless Steel NES 862/ASME 194/ASME 193 MIL-S-1222
Handwheel Material Aluminium/Stainless Steel
Connection Type Cartridge flanged to housing or manifold.
Housing welded or screwed (to be specified)
OVERALL DIMENSIONS (CARTRIDGE AND HOUSING)
Product
Designation
Estimated
Weight
Pipe Size
Cv
A
(mm/ins)
B
(mm/ins)
C
(mm/ins)
D
(mm/ins)
H
(mm/ins)
L
(mm/ins)
801-A2 2Kg/4.4lbs NB15/½” 6 75/2.95 28/1.1 125/4.9 64/2.5 97/3.8 215/8.46
801-B3 4Kg/8.8lbs NB20/¾” 18 95/3.7 29/1.14 145/5.71 86/3.39 16/0.63 228/8.98
801-C4 10Kg/22lbs NB25/1” 36 105/4.1 39/1.54 190/7.48 112/4.41 155/6.1 254/10.0
801-D5 26Kg/58lbs NB32/1¼” 55 115/4.5 44/1.73 250/9.84 137/5.39 180/7.09 280/11.0
801-E6 42Kg/92lbs NB40/1½” 140 180/7.1 50/1.97 285/11.22 175/6.89 230/9.06 304/12.0
801-G7 65Kg/143lbs NB50/2” 250 148/5.83 122/4.8 420/16.54 275/10.83 368/14.49 368/14.5
801-H8 65Kg/143lbs NB75/2.5” 250 148/5.83 122/4.8 420/16.54 275/10.83 368/14.49 368/14.5
PRODUCT OPTIONS
Stainless Steel bodies and cartridges for a wider range of
fluids such as Water, Steam, Oxygen, & Nitric Acid
Additional leak testing for valves to be used with Helium
Limit switches for confirmation of operation
Stainless Steel cartridges in manifolds for 400 bar systems Viton seals for operation at higher temperatures
sales@dynamiccontrols.co.uk T: +44 (0) 161 633 3933 sales@cunicocorp.com T: 562 733 4633
Rev. 7/31/14
7 of 27
8.
VALVE TECHNICAL DATA SHEET
CHECK VALVE 802
280 Bar 4000 psi
Technical Data
Design Specification Based on NES 375/ MIL-V-24109
Working Pressure 280 Bar / 4000 psi
Working Temperature Min –20ºC/-4ºF Max 120ºC/250ºF
Medium Air, Nitrogen, Helium, Oxygen. Hydraulic Fluid.
Quality Assurance Level En 10204, 3.1b also Full traceability – MIC Level 1
Cleaning TP102, Oxygen cleaning to MIL-STD-1330
Hydrostatic Test 420 Bar / 6000psi (High pressure and low pressure sides)
Airtight Test 308 Bar/ 3400psi
Shock Qualification MIL-S-901D
Vibration Qualification MIL-STD-167-1
Leakage Class Bubble Tight as per ANSI Class VI
Lift Pressure & Seating Pressure 0.5 bar (7.5 psi)
Housing Material 70/30 Copper Nickel to NES 780 Pt2, class 1/ASTM B151
Main Cartridge Components Material Nickel aluminium bronze to NES 833 part 2 /ASTM B150
Seals Material HNBR/ Fluorocarbon
Seat Material PEEK virgin FL350
Nuts/Studs Material Stainless Steel NES 862/ASME 194/ASME 193 MIL-S-1222
Connection Type Cartridge flanged to housing or manifold.
Housing welded or screwed (to be specified)
OVERALL DIMENSIONS (CARTRIDGE AND HOUSING)
Product
Designation
Estimated
Weight
Pipe Size
Cv
A
(mm/ins)
B
(mm/ins)
C
(mm/ins)
D
(mm/ins)
H
(mm/ins)
L
(mm/ins)
802-A2 1.3Kg/2.9lbs NB15/½” 5 80/3.5 19/0.75 90/3.54 64/2.52 80/3.15 215/8.46
802-B3 3.4Kg/7.5lbs NB20/¾” 16 105/413 19/0.75 110/4.33 86/3.39 95/6.81 228/8.98
802-C4 8.4Kg/18.5lb NB25/1” 35 145/5.71 23/0.91 135/5.31 112/4.41 120/4.72 254/10.0
802-D5 16.4Kg/36lbs NB32/1¼” 52 170/6.69 30/1.18 165/6.5 137/5.39 160/6.3 280/11.0
802-E6 39Kg/86lbs NB40/1½” 130 185/7.28 50/1.97 215/8.46 175/6.89 200/7.87 304/12.0
802-G7 65Kg/143lbs NB50/2” 235 164/6.46 115/4.53 251/9.88 275/10.83 368/14.49 368/14.5
PRODUCT OPTIONS
Stainless Steel bodies and cartridges for a wider range of
fluids such as Water, Steam, Oxygen, & Nitric Acid
Additional leak testing for valves to be used with Helium
Limit switches for confirmation of operation
Stainless Steel cartridges in manifolds for 280 bar systems Viton seals for operation at higher temperatures
sales@dynamiccontrols.co.uk T: +44 (0) 161 633 3933 sales@cunicocorp.com T: 562 733 4633
Rev. 7/31/14
8 of 27
9.
VALVE TECHNICAL DATA SHEET
CHECK VALVE 802
400 Bar 6000 psi
Technical Data
Design Specification Based on NES 375/ Mil-V-24109
Working Pressure 400 Bar / 6000 psi
Working Temperature Min –20ºC/-4ºF Max 120ºC/250ºF
Medium Air, Nitrogen, Helium, Oxygen. Hydraulic Fluid.
Quality Assurance Level En 10204, 3.1b also Full traceability – MIC Level 1
Cleaning TP102, Oxygen cleaning to MIL-STD-1330
Hydrostatic Test 600 Bar / 9000psi (High pressure and low pressure sides)
Airtight Test 440 Bar/ 6600psi
Shock Qualification MIL-S-901D
Vibration Qualification MIL-STD-167-1
Leakage Class Bubble Tight as per ANSI Class VI
Lift and seating pressure 0.5 bar (7.5 psi)
Housing Material 70/30 Copper Nickel to NES 780 Pt2, class 1/ASTM B151
Main Cartridge Components Material Nickel aluminium bronze to NES 833 part 2 /ASTM B150
Seals Material HNBR/ Fluorocarbon
Seat Material PEEK virgin FL350
Nuts/Studs Material Stainless Steel NES 862/ASME 194/ASME 193 MIL-S-1222
Connection Type Cartridge flanged to housing or manifold.
Housing welded or screwed (to be specified)
OVERALL DIMENSIONS (CARTRIDGE AND HOUSING)
Product
Designation
Estimated
Weight
Pipe Size
Cv
A
(mm/ins)
B
(mm/ins)
C
(mm/ins)
D
(mm/ins)
H
(mm/ins)
L
(mm/ins)
802-A2 1.3Kg/2.9lbs NB15/½” 5 80/3.5 19/0.75 90/3.54 64/2.52 80/3.15 215/8.46
802-B3 3.4Kg/7.5lbs NB20/¾” 16 105/413 19/0.75 110/4.33 86/3.39 95/6.81 228/8.98
802-C4 8.4Kg/18.5lb NB25/1” 35 145/5.71 23/0.91 135/5.31 112/4.41 120/4.72 254/10.0
802-D5 16.4Kg/36lbs NB32/1¼” 52 170/6.69 30/1.18 165/6.5 137/5.39 160/6.3 280/11.0
802-E6 39Kg/86lbs NB40/1½” 130 185/7.28 50/1.97 215/8.46 175/6.89 200/7.87 304/12.0
802-G7 65Kg/143lbs NB50/2” 235 164/6.46 115/4.53 251/9.88 275/10.83 368/14.49 368/14.5
PRODUCT OPTIONS
Stainless Steel bodies and cartridges for a wider range of
fluids such as Water, Steam, Oxygen, & Nitric Acid
Additional leak testing for valves to be used with Helium
Limit switches for confirmation of operation
Stainless Steel cartridges in manifolds for 400 bar systems Viton seals for operation at higher temperatures
sales@dynamiccontrols.co.uk T: +44 (0) 161 633 3933 sales@cunicocorp.com T: 562 733 4633
Rev. 7/31/14
9 of 27
10.
VALVE TECHNICAL DATA SHEET
SCREW DOWN NON-RETURN VALVE 803
280 Bar 4000 psi
Technical Data
Design Specification Based on NES 375/ MIL-V-24109
Working Pressure 280 Bar / 4000 psi
Working Temperature Min –20ºC/-4ºF Max 120ºC/250ºF
Medium Air, Nitrogen, Helium, Oxygen. Hydraulic Fluid.
Quality Assurance Level En 10204, 3.1b also Full traceability – MIC Level 1
Cleaning TP102, Oxygen cleaning to MIL-STD-1330
Hydrostatic Test 420 Bar / 6000psi (High pressure and low pressure sides)
Airtight Test 308 Bar/ 3400psi
Shock Qualification MIL-S-901D
Vibration Qualification MIL-STD-167-1
Leakage Class Bubble Tight as per ANSI Class VI
Housing Material 70/30 Copper Nickel to NES 780 Pt2, class 1/ASTM B151
Main Cartridge Components Material Nickel aluminium bronze to NES 833 part 2 /ASTM B150
Seals Material HNBR/ Fluorocarbon
Seat Material PEEK virgin FL350
Nuts/Studs Material Stainless Steel NES 862/ASME 194/ASME 193 MIL-S-1222
Handwheel Material Aluminium/Stainless Steel
Connection Type Cartridge flanged to housing or manifold.
Housing welded or screwed (to be specified)
OVERALL DIMENSIONS (CARTRIDGE AND HOUSING)
Product
Designation
Estimated
Weight
Pipe Size
Cv
A
(mm/ins)
B
(mm/ins)
C
(mm/ins)
D
(mm/ins)
H
(mm/ins)
L
(mm/ins)
803-A2 2Kg/4.4lbs NB15/½” 5 75/2.95 28/1.1 125/4.9 64/2.5 97/3.8 215/8.46
803-B3 4Kg/8.8lbs NB20/¾” 16 95/3.7 29/1.14 145/5.71 86/3.39 16/0.63 228/8.98
803-C4 10Kg/22lbs NB25/1” 35 105/4.1 39/1.54 190/7.48 112/4.41 155/6.1 254/10.0
803-D5 26Kg/58lbs NB32/1¼” 52 115/4.5 44/1.73 250/9.84 137/5.39 180/7.09 280/11.0
803-E6 42Kg/92lbs NB40/1½” 130 180/7.1 50/1.97 285/11.22 175/6.89 230/9.06 304/12.0
803-G7 65Kg/143lbs NB50/2” 235 148/5.83 122/4.8 420/16.54 275/10.83 368/14.49 368/14.5
PRODUCT OPTIONS
Stainless Steel bodies and cartridges for a wider range of
fluids such as Water, Steam, Oxygen, & Nitric Acid
Additional leak testing for valves to be used with Helium
Stainless Steel cartridges in manifolds for 280 bar systems Viton seals for operation at higher temperatures
sales@dynamiccontrols.co.uk T: +44 (0) 161 633 3933 sales@cunicocorp.com T: 562 733 4633
Rev. 7/31/14
10 of 27
11.
VALVE TECHNICAL DATA SHEET
SCREW DOWN NON-RETURN VALVE 803
400 Bar 6000 psi
Technical Data
Design Specification Based on NES 375/ MIL-V-24109
Working Pressure 400 Bar / 6000 psi
Working Temperature Min –20ºC/-4ºF Max 120ºC/250ºF
Medium Air, Nitrogen, Helium, Oxygen. Hydraulic Fluid.
Quality Assurance Level En 10204, 3.1b also Full traceability – MIC Level 1
Cleaning TP102, Oxygen cleaning to MIL-STD-1330
Hydrostatic Test 600 Bar / 9000psi (High pressure and low pressure sides)
Airtight Test 440 Bar/ 6600psi
Shock Qualification MIL-S-901D
Vibration Qualification MIL-STD-167-1
Leakage Class Bubble Tight as per ANSI Class VI
Housing Material 70/30 Copper Nickel to NES 780 Pt2, class 1/ASTM B151
Main Cartridge Components Material Nickel aluminium bronze to NES 833 part 2 /ASTM B150
Seals Material HNBR/ Fluorocarbon
Seat Material PEEK virgin FL350
Nuts/Studs Material Stainless Steel NES 862/ASME 194/ASME 193 MIL-S-1222
Handwheel Material Aluminium/Stainless Steel
Connection Type Cartridge flanged to housing or manifold.
Housing welded or screwed (to be specified)
OVERALL DIMENSIONS (CARTRIDGE AND HOUSING)
Product
Designation
Estimated
Weight
Pipe Size
Cv
A
(mm/ins)
B
(mm/ins)
C
(mm/ins)
D
(mm/ins)
H
(mm/ins)
L
(mm/ins)
803-A2 2Kg/4.4lbs NB15/½” 5 75/2.95 28/1.1 125/4.9 64/2.5 97/3.8 215/8.46
803-B3 4Kg/8.8lbs NB20/¾” 16 95/3.7 29/1.14 145/5.71 86/3.39 16/0.63 228/8.98
803-C4 10Kg/22lbs NB25/1” 35 105/4.1 39/1.54 190/7.48 112/4.41 155/6.1 254/10.0
803-D5 26Kg/58lbs NB32/1¼” 52 115/4.5 44/1.73 250/9.84 137/5.39 180/7.09 280/11.0
803-E6 42Kg/92lbs NB40/1½” 130 180/7.1 50/1.97 285/11.22 175/6.89 230/9.06 304/12.0
803-G7 65Kg/143lbs NB50/2” 235 148/5.83 122/4.8 420/16.54 275/10.83 368/14.49 368/14.5
PRODUCT OPTIONS
Stainless Steel bodies and cartridges for a wider range of
fluids such as Water, Steam, Oxygen, & Nitric Acid
Additional leak testing for valves to be used with Helium
Stainless Steel cartridges in manifolds for 400 bar systems Viton seals for operation at higher temperatures
sales@dynamiccontrols.co.uk T: +44 (0) 161 633 3933 sales@cunicocorp.com T: 562 733 4633
Rev. 7/31/14
11 of 27
12.
VALVE TECHNICAL DATA SHEET
NORMALLY CLOSED AIR ATUATED STOP VALVE 806
280 Bar 4000 psi
Technical Data
Design Specification Based on NES 375/ MIL-V-24109
Working Pressure 280 Bar / 4000 psi
Working Temperature Min –20ºC/-4ºF Max 120ºC/250ºF
Medium Air, Nitrogen, Helium, Oxygen. Hydraulic Fluid.
Quality Assurance Level En 10204, 3.1b also Full traceability – MIC Level 1
Cleaning TP102, Oxygen cleaning to MIL-STD-1330
Hydrostatic Test 420 Bar / 6000psi (High pressure and low pressure sides)
Airtight Test 308 Bar/ 3400psi
Shock Qualification MIL-S-901D
Vibration Qualification MIL-STD-167-1
Leakage Class Bubble Tight as per ANSI Class VI
Housing Material 70/30 Copper Nickel to NES 780 Pt2, class 1/ASTM B151
Main Cartridge Components Material Nickel aluminium bronze to NES 833 part 2 /ASTM B150
Seals Material HNBR/ Fluorocarbon
Seat Material PEEK virgin FL350
Nuts/Studs Material Stainless Steel NES 862/ASME 194/ASME 193 MIL-S-1222
Actuator Type Single Acting Spring Return, Direct Mount Piston
Actuator Action Air to Open
Actuator Pressure 6 bar/100 psi maximum
Response Time Up to 25 NB <2sec to open, < 3sec to close
Above 25NB <5 sec to open <7sec to close
OVERALL DIMENSIONS (CARTRIDGE AND HOUSING)
Product
Designation
Estimated
Weight
Pipe Size
Cv
A
(mm/ins)
B
(mm/ins)
C
(mm/ins)
D
(mm/ins)
H
(mm/ins)
L
(mm/ins)
806-A2 3Kg/6.6lbs NB15/½” 6 5/0.2 90/3.5 325/12.8 102/4.0 250/9.8 215/8.46
806-B3 6Kg/13.2lbs NB20/¾” 18 38/1.5 135/5.3 384/15.1 116/4.6 275/10.8 228/8.98
806-C4 15Kg/33lbs NB25/1” 36 14/0.6 150/5.9 480/18.9 130/5.1 350/13.8 254/10.0
806-D5 39Kg/87lbs NB32/1¼” 55 15/0.6 140/5.5 540/21.3 180/7.1 400/15.8 280/11.0
806-E6 63Kg/138lbs NB40/1½” 140 25/1 224/8.8 676/26.7 210/8.3 490/19.3 304/12.0
806-G7 98Kg/216lbs NB50/2” 250 30/1.2 310/12.2 825/32.5 270/10.6 650/25.6 368/14.5
PRODUCT OPTIONS
Stainless Steel bodies and cartridges for a wider range of
fluids such as Water, Steam, Oxygen, & Nitric Acid
Additional leak testing for valves to be used with Helium
Limit switches for confirmation of operation
12 of 27
sales@dynamiccontrols.co.uk T: +44 (0) 161 633 3933 sales@cunicocorp.com T: 562 733 4633
Rev. 7/31/14
13.
VALVE TECHNICAL DATA SHEET
NORMALLY CLOSED AIR ATUATED STOP VALVE 806
400 Bar 6000 psi
Technical Data
Design Specification Based on NES 375/ MIL-V-24109
Working Pressure 400 Bar / 6000 psi
Working Temperature Min –20ºC/-4ºF Max 120ºC/250ºF
Medium Air, Nitrogen, Helium, Oxygen. Hydraulic Fluid.
Quality Assurance Level En 10204, 3.1b also Full traceability – MIC Level 1
Cleaning TP102, Oxygen cleaning to MIL-STD-1330
Hydrostatic Test 600 Bar / 9000psi (High pressure and low pressure sides)
Airtight Test 440 Bar/ 6600psi
Shock Qualification MIL-S-901D
Vibration Qualification MIL-STD-167-1
Leakage Class Bubble Tight as per ANSI Class VI
Housing Material 70/30 Copper Nickel to NES 780 Pt2, class 1/ASTM B151
Main Cartridge Components Material Nickel aluminium bronze to NES 833 part 2 /ASTM B150
Seals Material HNBR/ Fluorocarbon
Seat Material PEEK virgin FL350
Nuts/Studs Material Stainless Steel NES 862/ASME 194/ASME 193 MIL-S-1222
Actuator Type Single Acting Spring Return, Direct Mount Piston
Actuator Action Air to Open
Actuator Pressure 6 bar/100 psi maximum
Response Time Up to 25 NB <2sec to open, < 3sec to close
Above 25NB <5 sec to open <7sec to close
OVERALL DIMENSIONS (CARTRIDGE AND HOUSING)
Product
Designation
Estimated
Weight
Pipe Size
Cv
A
(mm/ins)
B
(mm/ins)
C
(mm/ins)
D
(mm/ins)
H
(mm/ins)
L
(mm/ins)
806-A2 3Kg/6.6lbs NB15/½” 6 5/0.2 90/3.5 325/12.8 102/4.0 250/9.8 215/8.46
806-B3 6Kg/13.2lbs NB20/¾” 18 38/1.5 135/5.3 384/15.1 116/4.6 275/10.8 228/8.98
806-C4 15Kg/33lbs NB25/1” 36 14/0.6 150/5.9 480/18.9 130/5.1 350/13.8 254/10.0
806-D5 39Kg/87lbs NB32/1¼” 55 15/0.6 140/5.5 540/21.3 180/7.1 400/15.8 280/11.0
806-E6 63Kg/138lbs NB40/1½” 140 25/1 224/8.8 676/26.7 210/8.3 490/19.3 304/12.0
806-G7 98Kg/216lbs NB50/2” 250 30/1.2 310/12.2 825/32.5 270/10.6 650/25.6 368/14.5
PRODUCT OPTIONS
Stainless Steel bodies and cartridges for a wider range of
fluids such as Water, Steam, Oxygen, & Nitric Acid
Additional leak testing for valves to be used with Helium
Limit switches for confirmation of operation
13 of 27
sales@dynamiccontrols.co.uk T: +44 (0) 161 633 3933 sales@cunicocorp.com T: 562 733 4633
Rev. 7/31/14
14.
VALVE TECHNICAL DATA SHEET
NORMALLY OPEN AIR ATUATED STOP VALVE 807
280 Bar 4000 psi
Technical Data
Design Specification Based on NES 375/ MIL-V-24109
Working Pressure 280 Bar / 4000 psi
Working Temperature Min –20ºC/-4ºF Max 120ºC/250ºF
Medium Air, Nitrogen, Helium, Oxygen. Hydraulic Fluid.
Quality Assurance Level En 10204, 3.1b also Full traceability – MIC Level 1
Cleaning TP102, Oxygen cleaning to MIL-STD-1330
Hydrostatic Test 420 Bar / 6000psi (High pressure and low pressure sides)
Airtight Test 308 Bar/ 3400psi
Shock Qualification MIL-S-901D
Vibration Qualification MIL-STD-167-1
Leakage Class Bubble Tight as per ANSI Class VI
Housing Material 70/30 Copper Nickel to NES 780 Pt2, class 1/ASTM B151
Main Cartridge Components Material Nickel aluminium bronze to NES 833 part 2 /ASTM B150
Seals Material HNBR/ Fluorocarbon
Seat Material PEEK virgin FL350
Nuts/Studs Material Stainless Steel NES 862/ASME 194/ASME 193 MIL-S-1222
Actuator Type Single Acting Spring Return, Direct Mount Piston
Actuator Action Air to Close
Actuator Pressure 6 bar/100 psi maximum
Response Time Up to 25 NB <2sec to close, < 3sec to open
Above 25NB <5 sec to close <7sec to open
OVERALL DIMENSIONS (CARTRIDGE AND HOUSING)
Product
Designation
Estimated
Weight
Pipe Size
Cv
A
(mm/ins)
B
(mm/ins)
C
(mm/ins)
D
(mm/ins)
H
(mm/ins)
L
(mm/ins)
807-A2 3Kg/6.6lbs NB15/½” 6 5/0.2 90/3.5 325/12.8 102/4.0 250/9.8 215/8.46
807-B3 6Kg/13.2lbs NB20/¾” 18 38/1.5 135/5.3 384/15.1 116/4.6 275/10.8 228/8.98
807-C4 15Kg/33lbs NB25/1” 36 14/0.6 150/5.9 480/18.9 130/5.1 350/13.8 254/10.0
807-D5 39Kg/87lbs NB32/1¼” 55 15/0.6 140/5.5 540/21.3 180/7.1 400/15.8 280/11.0
807-E6 63Kg/138lbs NB40/1½” 140 25/1 224/8.8 676/26.7 210/8.3 490/19.3 304/12.0
807-G7 98Kg/216lbs NB50/2” 250 30/1.2 310/12.2 825/32.5 270/10.6 650/25.6 368/14.5
PRODUCT OPTIONS
Stainless Steel bodies and cartridges for a wider range of
fluids such as Water, Steam, Oxygen, & Nitric Acid
Additional leak testing for valves to be used with Helium
Limit switches for confirmation of operation
14 of 27
sales@dynamiccontrols.co.uk T: +44 (0) 161 633 3933 sales@cunicocorp.com T: 562 733 4633
Rev. 7/31/14
15.
VALVE TECHNICAL DATA SHEET
NORMALLY OPEN AIR ATUATED STOP VALVE 807
400 Bar 6000 psi
Technical Data
Design Specification Based on NES 375/ MIL-V-24109
Working Pressure 400 Bar / 6000 psi
Working Temperature Min –20ºC/-4ºF Max 120ºC/250ºF
Medium Air, Nitrogen, Helium, Oxygen. Hydraulic Fluid.
Quality Assurance Level En 10204, 3.1b also Full traceability – MIC Level 1
Cleaning TP102, Oxygen cleaning to MIL-STD-1330
Hydrostatic Test 600 Bar / 9000psi (High pressure and low pressure sides)
Airtight Test 440 Bar/ 6600psi
Shock Qualification MIL-S-901D
Vibration Qualification MIL-STD-167-1
Leakage Class Bubble Tight as per ANSI Class VI
Housing Material 70/30 Copper Nickel to NES 780 Pt2, class 1/ASTM B151
Main Cartridge Components Material Nickel aluminium bronze to NES 833 part 2 /ASTM B150
Seals Material HNBR/ Fluorocarbon
Seat Material PEEK virgin FL350
Nuts/Studs Material Stainless Steel NES 862/ASME 194/ASME 193 MIL-S-1222
Actuator Type Single Acting Spring Return, Direct Mount Piston
Actuator Action Air to Close
Actuator Pressure 6 bar/100 psi maximum
Response Time Up to 25 NB <2sec to close, < 3sec to open
Above 25NB <5 sec to close <7sec to open
OVERALL DIMENSIONS (CARTRIDGE AND HOUSING)
Product
Designation
Estimated
Weight
Pipe Size
Cv
A
(mm/ins)
B
(mm/ins)
C
(mm/ins)
D
(mm/ins)
H
(mm/ins)
L
(mm/ins)
807-A2 3Kg/6.6lbs NB15/½” 6 5/0.2 90/3.5 325/12.8 102/4.0 250/9.8 215/8.46
807-B3 6Kg/13.2lbs NB20/¾” 18 38/1.5 135/5.3 384/15.1 116/4.6 275/10.8 228/8.98
807-C4 15Kg/33lbs NB25/1” 36 14/0.6 150/5.9 480/18.9 130/5.1 350/13.8 254/10.0
807-D5 39Kg/87lbs NB32/1¼” 55 15/0.6 140/5.5 540/21.3 180/7.1 400/15.8 280/11.0
807-E6 63Kg/138lbs NB40/1½” 140 25/1 224/8.8 676/26.7 210/8.3 490/19.3 304/12.0
807-G7 98Kg/216lbs NB50/2” 250 30/1.2 310/12.2 825/32.5 270/10.6 650/25.6 368/14.5
PRODUCT OPTIONS
Stainless Steel bodies and cartridges for a wider range of
fluids such as Water, Steam, Oxygen, & Nitric Acid
Additional leak testing for valves to be used with Helium
Limit switches for confirmation of operation
sales@dynamiccontrols.co.uk T: +44 (0) 161 633 3933 sales@cunicocorp.com T: 562 733 4633
Rev. 7/31/14
15 of 27
16.
VALVE TECHNICAL DATA SHEET
FLUSHING ADAPTOR 810
280 Bar 4000 psi
Technical Data
Design Specification Based on NES 375
Working Pressure 280 Bar / 4000 psi
Working Temperature Min –20ºC/-4ºF Max 120ºC/250ºF
Medium Air, Nitrogen, Helium, Oxygen. Hydraulic Fluid.
Quality Assurance Level En 10204, 3.1b also Full traceability – MIC Level 1
Cleaning TP102, Oxygen cleaning to MIL-STD-1330
Hydrostatic Test 420 Bar / 6000psi
Porting Arrangement To facilitate different flow directions
Shock Qualification Not Required
Vibration Qualification Not Required
Leakage Class Not Applicable
Housing Material 70/30 Copper Nickel to NES 780 Pt2, class 1/ASTM B151
Main Cartridge Components Material Nickel aluminium bronze to NES 833 part 2 /ASTM B150, Aluminium
Seals Material HNBR/ Fluorocarbon
Seat Material Not Applicable
Nuts/Studs Material Stainless Steel NES 862/ASME 194/ASME 193 MIL-S-1222
Connection Type Cartridge flanged to housing or manifold.
Housing welded or screwed (to be specified)
OVERALL DIMENSIONS (CARTRIDGE AND HOUSING)
Product
Designation
Estimated
Weight
Pipe Size
Cv
A
(mm/ins)
B
(mm/ins)
C
(mm/ins)
D
(mm/ins)
H
(mm/ins)
L
(mm/ins)
810-A2 1.3Kg/2.9lbs NB15/½” 5 80/3.5 19/0.75 90/3.54 64/2.52 80/3.15 215/8.46
810-B3 3.4Kg/7.5lbs NB20/¾” 16 105/413 19/0.75 110/4.33 86/3.39 95/6.81 228/8.98
810-C4 8.4Kg/18.5lb NB25/1” 35 145/5.71 23/0.91 135/5.31 112/4.41 120/4.72 254/10.0
810-D5 16.4Kg/36lbs NB32/1¼” 52 170/6.69 30/1.18 165/6.5 137/5.39 160/6.3 280/11.0
810-E6 39Kg/86lbs NB40/1½” 130 185/7.28 50/1.97 215/8.46 175/6.89 200/7.87 304/12.0
810-G7 65Kg/143lbs NB50/2” 235 164/6.46 115/4.53 251/9.88 275/10.83 368/14.49 368/14.5
PRODUCT OPTIONS
Stainless Steel bodies and cartridges for a wider range of
fluids such as Water, Steam, Oxygen, & Nitric Acid
Stainless Steel cartridges in manifolds for 280 bar systems Viton seals for operation at higher temperatures
sales@dynamiccontrols.co.uk T: +44 (0) 161 633 3933 sales@cunicocorp.com T: 562 733 4633
Rev. 7/31/14
16 of 27
17.
VALVE TECHNICAL DATA SHEET
FLUSHING ADAPTOR 810
400 Bar 6000 psi
Technical Data
Design Specification Based on NES 375
Working Pressure 400 Bar / 6000 psi
Working Temperature Min –20ºC/-4ºF Max 120ºC/250ºF
Medium Air, Nitrogen, Helium, Oxygen. Hydraulic Fluid.
Quality Assurance Level En 10204, 3.1b also Full traceability – MIC Level 1
Cleaning TP102, Oxygen cleaning to MIL-STD-1330
Hydrostatic Test 600 Bar / 9000psi
Porting Arrangement To facilitate different flow directions
Shock Qualification Not Required
Vibration Qualification Not Required
Leakage Class Not Applicable
Housing Material 70/30 Copper Nickel to NES 780 Pt2, class 1/ASTM B151
Main Cartridge Components Material Nickel aluminium bronze to NES 833 part 2 /ASTM B150, Aluminium
Seals Material HNBR/ Fluorocarbon
Seat Material Not Applicable
Nuts/Studs Material Stainless Steel NES 862/ASME 194/ASME 193 MIL-S-1222
Connection Type Cartridge flanged to housing or manifold.
Housing welded or screwed (to be specified)
OVERALL DIMENSIONS (CARTRIDGE AND HOUSING)
Product
Designation
Estimated
Weight
Pipe Size
Cv
A
(mm/ins)
B
(mm/ins)
C
(mm/ins)
D
(mm/ins)
H
(mm/ins)
L
(mm/ins)
810-A2 1.3Kg/2.9lbs NB15/½” 5 80/3.5 19/0.75 90/3.54 64/2.52 80/3.15 215/8.46
810-B3 3.4Kg/7.5lbs NB20/¾” 16 105/413 19/0.75 110/4.33 86/3.39 95/6.81 228/8.98
810-C4 8.4Kg/18.5lb NB25/1” 35 145/5.71 23/0.91 135/5.31 112/4.41 120/4.72 254/10.0
810-D5 16.4Kg/36lbs NB32/1¼” 52 170/6.69 30/1.18 165/6.5 137/5.39 160/6.3 280/11.0
810-E6 39Kg/86lbs NB40/1½” 130 185/7.28 50/1.97 215/8.46 175/6.89 200/7.87 304/12.0
810-G7 65Kg/143lbs NB50/2” 235 164/6.46 115/4.53 251/9.88 275/10.83 368/14.49 368/14.5
PRODUCT OPTIONS
Stainless Steel bodies and cartridges for a wider range of
fluids such as Water, Steam, Oxygen, & Nitric Acid
Stainless Steel cartridges in manifolds for 400 bar systems Viton seals for operation at higher temperatures
sales@dynamiccontrols.co.uk T: +44 (0) 161 633 3933 sales@cunicocorp.com T: 562 733 4633
Rev. 7/31/14
17 of 27
18.
VALVE TECHNICAL DATA SHEET
RELIEF VALVE 813
280 Bar 4000 psi
Technical Data
Design Specification Based on NES 375/ MIL-V-22549
Working Pressure 280 Bar / 4000 psi
Working Temperature Min –20ºC/-4ºF Max 120ºC/250ºF
Medium Air, Nitrogen, Helium, Oxygen. Hydraulic Fluid.
Quality Assurance Level En 10204, 3.1b also Full traceability – MIC Level 1
Cleaning TP102, Oxygen cleaning to MIL-STD-1330
Hydrostatic Test 420 Bar / 6000psi (High pressure and low pressure sides)
Ranges Available 8 bands ranging form 1 bar (7.5 psi) to 370 bar (5365 psi)
Shock Qualification MIL-S-901D
Vibration Qualification MIL-STD-167-1
Maximum Accumulation Pressure >7 bar set point: Set point plus 10%, <7 bar Set point: 2 bar
Minimum Re-seat Pressure >7 bar set point: Set point minus 10%, <7 bar Set point: 2 bar
Housing Material 70/30 Copper Nickel to NES 780 Pt2, class 1/ASTM B151
Main Cartridge Components Material Nickel aluminium bronze to NES 833 part 2 /ASTM B150
Seals Material HNBR/ Fluorocarbon
Seat Material PEEK virgin FL350
Nuts/Studs Material Stainless Steel NES 862/ASME 194/ASME 193 MIL-S-1222
Connection Type Cartridge flanged to housing or manifold.
Housing welded or screwed (to be specified)
OVERALL DIMENSIONS (CARTRIDGE AND HOUSING)
Product
Designation
Estimated
Weight
Pipe Size
Kdr
A
(mm/ins)
B
(mm/ins)
C
(mm/ins)
D
(mm/ins)
H
(mm/ins)
L
(mm/ins)
813-A2 4Kg/8.8lbs NB15/½” 0.46 20/0.79 110/4.33 125/4.9 60/2.36 240/9.45 215/8.46
813-B3 7Kg/15.4lbs NB20/¾” 0.39 28/1.1 118/4.65 145/5.71 73/2.87 250/9.84 228/8.98
813-C4 12Kg/26.4lbs NB25/1” 0.31 35/1.38 125/4.92 190/7.48 89/3.5 332/13.07 254/10.0
813-D5 30Kg/66lbs NB32/1¼” 0.28 75/2.95 165/6.5 250/9.84 109/4.29 414/16.3 280/11.0
813-E6 52Kg/115lbs NB40/1½” 0.24 130/5.12 220/8.66 285/11.22 140/5.51 554/21.81 304/12.0
813-G7 75Kg/165lbs NB50/2” 0.24 192/7.56 282/11.1 420/16.54 200/7.87 705/27.76 368/14.5
PRODUCT OPTIONS
Stainless Steel bodies and cartridges for a wider range of
fluids such as Water, Steam, Oxygen, & Nitric Acid
Stainless Steel cartridges in manifolds for 280 bar systems Viton seals for operation at higher temperatures
sales@dynamiccontrols.co.uk T: +44 (0) 161 633 3933 sales@cunicocorp.com T: 562 733 4633
Rev. 7/31/14
18 of 27
19.
VALVE TECHNICAL DATA SHEET
RELIEF VALVE 813
400 Bar 6000 psi
Technical Data
Design Specification Based on NES 375/ Mil-V-22549
Working Pressure 400 Bar / 6000 psi
Working Temperature Min –20ºC/-4ºF Max 120ºC/250ºF
Medium Air, Nitrogen, Helium, Oxygen. Hydraulic Fluid.
Quality Assurance Level En 10204, 3.1b also Full traceability – MIC Level 1
Cleaning TP102, Oxygen cleaning to MIL-STD-1330
Hydrostatic Test 600 Bar / 9000psi (High pressure and low pressure sides)
Ranges Available 8 bands ranging form 1 bar (7.5 psi) to 370 bar (5365 psi)
Shock Qualification MIL-S-901D
Vibration Qualification MIL-STD-167-1
Maximum Accumulation Pressure >7 bar set point: Set point plus 10%, <7 bar Set point: 2 bar
Minimum Re-seat Pressure >7 bar set point: Set point minus 10%, <7 bar Set point: 2 bar
Housing Material 70/30 Copper Nickel to NES 780 Pt2, class 1/ASTM B151
Main Cartridge Components Material Nickel aluminium bronze to NES 833 part 2 /ASTM B150
Seals Material HNBR/ Fluorocarbon
Seat Material PEEK virgin FL350
Nuts/Studs Material Stainless Steel NES 862/ASME 194/ASME 193 MIL-S-1222
Connection Type Cartridge flanged to housing or manifold.
Housing welded or screwed (to be specified)
OVERALL DIMENSIONS (CARTRIDGE AND HOUSING)
Product
Designation
Estimated
Weight
Pipe Size
Kdr
A
(mm/ins)
B
(mm/ins)
C
(mm/ins)
D
(mm/ins)
H
(mm/ins)
L
(mm/ins)
813-A2 4Kg/8.8lbs NB15/½” 0.46 20/0.79 110/4.33 125/4.9 60/2.36 240/9.45 215/8.46
813-B3 7Kg/15.4lbs NB20/¾” 0.39 28/1.1 118/4.65 145/5.71 73/2.87 250/9.84 228/8.98
813-C4 12Kg/26.4lbs NB25/1” 0.31 35/1.38 125/4.92 190/7.48 89/3.5 332/13.07 254/10.0
813-D5 30Kg/66lbs NB32/1¼” 0.28 75/2.95 165/6.5 250/9.84 109/4.29 414/16.3 280/11.0
813-E6 52Kg/115lbs NB40/1½” 0.24 130/5.12 220/8.66 285/11.22 140/5.51 554/21.81 304/12.0
813-G7 75Kg/165lbs NB50/2” 0.24 192/7.56 282/11.1 420/16.54 200/7.87 705/27.76 368/14.5
PRODUCT OPTIONS
Stainless Steel bodies and cartridges for a wider range of
fluids such as Water, Steam, Oxygen, & Nitric Acid
Stainless Steel cartridges in manifolds for 400 bar systems Viton seals for operation at higher temperatures
sales@dynamiccontrols.co.uk T: +44 (0) 161 633 3933 sales@cunicocorp.com T: 562 733 4633
Rev. 7/31/14
19 of 27
20.
VALVE TECHNICAL DATA SHEET
FILTER VALVE 814
280 Bar 4000 psi
Technical Data
Design Specification Based on NES 375/ Mil-F-8815
Working Pressure 280 Bar / 4000 psi
Working Temperature Min –20ºC/-4ºF Max 120ºC/250ºF
Medium Air, Nitrogen, Helium, Hydraulic Fluid.
Quality Assurance Level En 10204, 3.1b also Full traceability – MIC Level 1
Cleaning TP102, Oxygen cleaning to MIL-STD-1330
Hydrostatic Test 420 Bar / 6000psi (High pressure and low pressure sides)
Filtration Range 6 bands ranging for 10μ to 250μ absolute
Shock Qualification MIL-S-901D
Vibration Qualification MIL-STD-167-1
Maximum ΔP at rated flow 0.1 kg/cm2
Filter Mesh Minimum Surface Area 500% of Inlet Pipe Area
Housing Material 70/30 Copper Nickel to NES 780 Pt2, class 1/ASTM B151
Main Cartridge Components Material Nickel aluminium bronze to NES 833 part 2 /ASTM B150
Seals Material HNBR/ Fluorocarbon
Seat Material Not Applicable
Nuts/Studs Material Stainless Steel NES 862/ASME 194/ASME 193 MIL-S-1222
Handwheel Material Not Applicable
Connection Type Cartridge flanged to housing or manifold.
Housing welded or screwed (to be specified)
OVERALL DIMENSIONS (CARTRIDGE AND HOUSING)
Product
Designation
Estimated
Weight
Pipe Size
Cv
A
(mm/ins)
B
(mm/ins)
C
(mm/ins)
D
(mm/ins)
H
(mm/ins)
L
(mm/ins)
814-A2 1.3Kg/2.9lbs NB15/½” N/A 80/3.5 19/0.75 90/3.54 64/2.52 80/3.15 215/8.46
814-B3 3.4Kg/7.5lbs NB20/¾” N/A 105/413 19/0.75 110/4.33 86/3.39 95/6.81 228/8.98
814-C4 8.4Kg/18.5lb NB25/1” N/A 145/5.71 23/0.91 135/5.31 112/4.41 120/4.72 254/10.0
814-D5 16.4Kg/36lbs NB32/1¼” N/A 170/6.69 30/1.18 165/6.5 137/5.39 160/6.3 280/11.0
814-E6 39Kg/86lbs NB40/1½” N/A 185/7.28 50/1.97 215/8.46 175/6.89 200/7.87 304/12.0
814-G7 65Kg/143lbs NB50/2” N/A 164/6.46 115/4.53 251/9.88 275/10.83 368/14.49 368/14.5
PRODUCT OPTIONS
Stainless Steel bodies and cartridges for a wider range of
fluids such as Water, Steam, & Nitric Acid
Stainless Steel cartridges in manifolds for 280 bar systems Viton seals for operation at higher temperatures
20 of 27
sales@dynamiccontrols.co.uk T: +44 (0) 161 633 3933 sales@cunicocorp.com T: 562 733 4633
Rev. 7/31/14
21.
VALVE TECHNICAL DATA SHEET
FILTER VALVE 814
400 Bar 6000 psi
Technical Data
Design Specification Based on NES 375/ MIL-F-8815
Working Pressure 400 Bar / 6000 psi
Working Temperature Min –20ºC/-4ºF Max 120ºC/250ºF
Medium Air, Nitrogen, Helium, Hydraulic Fluid.
Quality Assurance Level En 10204, 3.1b also Full traceability – MIC Level 1
Cleaning TP102, Oxygen cleaning to MIL-STD-1330
Hydrostatic Test 600 Bar / 9000psi (High pressure and low pressure sides)
Filtration Range 6 bands ranging for 10μ to 250μ absolute
Shock Qualification MIL-S-901D
Vibration Qualification MIL-STD-167-1
Maximum ΔP at rated flow 0.1 kg/cm2
Filter Mesh Minimum Surface Area 500% of Inlet Pipe Area
Housing Material 70/30 Copper Nickel to NES 780 Pt2, class 1/ASTM B151
Main Cartridge Components Material Nickel aluminium bronze to NES 833 part 2 /ASTM B150
Seals Material HNBR/ Fluorocarbon
Seat Material Not Applicable
Nuts/Studs Material Stainless Steel NES 862/ASME 194/ASME 193 MIL-S-1222
Handwheel Material Not Applicable
Connection Type Cartridge flanged to housing or manifold.
Housing welded or screwed (to be specified)
OVERALL DIMENSIONS (CARTRIDGE AND HOUSING)
Product
Designation
Estimated
Weight
Pipe Size
Cv
A
(mm/ins)
B
(mm/ins)
C
(mm/ins)
D
(mm/ins)
H
(mm/ins)
L
(mm/ins)
814-A2 1.3Kg/2.9lbs NB15/½” N/A 80/3.5 19/0.75 90/3.54 64/2.52 80/3.15 215/8.46
814-B3 3.4Kg/7.5lbs NB20/¾” N/A 105/413 19/0.75 110/4.33 86/3.39 95/6.81 228/8.98
814-C4 8.4Kg/18.5lb NB25/1” N/A 145/5.71 23/0.91 135/5.31 112/4.41 120/4.72 254/10.0
814-D5 16.4Kg/36lbs NB32/1¼” N/A 170/6.69 30/1.18 165/6.5 137/5.39 160/6.3 280/11.0
814-E6 39Kg/86lbs NB40/1½” N/A 185/7.28 50/1.97 215/8.46 175/6.89 200/7.87 304/12.0
814-G7 65Kg/143lbs NB50/2” N/A 164/6.46 115/4.53 251/9.88 275/10.83 368/14.49 368/14.5
PRODUCT OPTIONS
Stainless Steel bodies and cartridges for a wider range of
fluids such as Water, Steam, & Nitric Acid
Stainless Steel cartridges in manifolds for 400 bar systems Viton seals for operation at higher temperatures
21 of 27
sales@dynamiccontrols.co.uk T: +44 (0) 161 633 3933 sales@cunicocorp.com T: 562 733 4633
Rev. 7/31/14
22.
VALVE TECHNICAL DATA SHEET
DOME LOADED PRESSURE REGULATOR 817
280 Bar 4000 psi
Technical Data
Design Specification Based on NES 375/ MIL-V-2961
Working Pressure 280 Bar / 4000 psi
Working Temperature Min –20ºC/-4ºF Max 120ºC/250ºF
Medium Air, Nitrogen, Helium, Oxygen. Hydraulic Fluid.
Quality Assurance Level En 10204, 3.1b also Full traceability – MIC Level 1
Cleaning TP102, Oxygen cleaning to MIL-STD-1330
Hydrostatic Test 420 Bar / 6000psi (High pressure and low pressure sides)
Dome Setting 1:1 Ratio with set pressure
Shock Qualification MIL-S-901D
Vibration Qualification MIL-STD-167-1
Maximum Lock-up Pressure >7 bar set point: Set point plus 10%, <7 bar Set point: 2 bar
Minimum Droop Pressure >7 bar set point: Set point minus 10%, <7 bar Set point: 2 bar
Housing Material 70/30 Copper Nickel to NES 780 Pt2, class 1/ASTM B151
Main Cartridge Components Material Nickel aluminium bronze to NES 833 part 2 /ASTM B150
Seals Material HNBR/ Fluorocarbon
Seat Material PEEK virgin FL350
Nuts/Studs Material Stainless Steel NES 862/ASME 194/ASME 193 MIL-S-1222
Connection Type Cartridge flanged to housing or manifold.
Housing welded or screwed (to be specified)
OVERALL DIMENSIONS (CARTRIDGE AND HOUSING)
Product
Designation
Estimated
Weight
Pipe Size
Cv
A
(mm/ins)
B
(mm/ins)
C
(mm/ins)
D
(mm/ins)
H
(mm/ins)
L
(mm/ins)
817-A2 4Kg/8.8lbs NB15/½” 1.5 26/1.02 63/2.48 125/4.9 75/2.95 225/8.86 215/8.46
817-B3 7Kg/15.4lbs NB20/¾” 4 35/1.38 105/4.13 145/5.71 113/4.45 295/11.61 228/8.98
817-C4 12Kg/26.4lbs NB25/1” 7 77.3.03 124/4.88 190/7.48 140/5.51 310/12.2 254/10.0
817-D5 30Kg/66lbs NB32/1¼” 12 103/4.06 150/5.91 250/9.84 178/7.0 375/14.76 280/11.0
817-E6 52Kg/115lbs NB40/1½” 25 149/5.87 196/7.72 285/11.22 230/9.06 490/19.29 304/12.0
817-G7 75Kg/165lbs NB50/2” 46 200/7.87 248/9.76 420/16.54 350/13.78 620/20.41 368/14.5
PRODUCT OPTIONS
Stainless Steel bodies and cartridges for a wider range of
fluids such as Water, Steam, Oxygen, & Nitric Acid
Stainless Steel cartridges in manifolds for 280 bar systems Viton seals for operation at higher temperatures
sales@dynamiccontrols.co.uk T: +44 (0) 161 633 3933 sales@cunicocorp.com T: 562 733 4633
Rev. 7/31/14
22 of 27
23.
VALVE TECHNICAL DATA SHEET
DOME LOADED PRESSURE REGULATOR 817
400 Bar 6000 psi
Technical Data
Design Specification Based on NES 375/ MIL-V-2961
Working Pressure 400 Bar / 6000 psi
Working Temperature Min –20ºC/-4ºF Max 120ºC/250ºF
Medium Air, Nitrogen, Helium, Oxygen. Hydraulic Fluid.
Quality Assurance Level En 10204, 3.1b also Full traceability – MIC Level 1
Cleaning TP102, Oxygen cleaning to MIL-STD-1330
Hydrostatic Test 600 Bar / 9000psi (High pressure and low pressure sides)
Dome setting 1:1 Ratio with set pressure
Shock Qualification MIL-S-901D
Vibration Qualification MIL-STD-167-1
Maximum Lock-up Pressure >7 bar set point: Set point plus 10%, <7 bar Set point: 2 bar
Minimum Droop Pressure >7 bar set point: Set point minus 10%, <7 bar Set point: 2 bar
Housing Material 70/30 Copper Nickel to NES 780 Pt2, class 1/ASTM B151
Main Cartridge Components Material Nickel aluminium bronze to NES 833 part 2 /ASTM B150
Seals Material HNBR/ Fluorocarbon
Seat Material PEEK virgin FL350
Nuts/Studs Material Stainless Steel NES 862/ASME 194/ASME 193 MIL-S-1222
Connection Type Cartridge flanged to housing or manifold.
Housing welded or screwed (to be specified)
OVERALL DIMENSIONS (CARTRIDGE AND HOUSING)
Product
Designation
Estimated
Weight
Pipe Size
Cv
A
(mm/ins)
B
(mm/ins)
C
(mm/ins)
D
(mm/ins)
H
(mm/ins)
L
(mm/ins)
817-A2 4Kg/8.8lbs NB15/½” 1.5 26/1.02 63/2.48 125/4.9 75/2.95 225/8.86 215/8.46
817-B3 7Kg/15.4lbs NB20/¾” 4 35/1.38 105/4.13 145/5.71 113/4.45 295/11.61 228/8.98
817-C4 12Kg/26.4lbs NB25/1” 7 77.3.03 124/4.88 190/7.48 140/5.51 310/12.2 254/10.0
817-D5 30Kg/66lbs NB32/1¼” 12 103/4.06 150/5.91 250/9.84 178/7.0 375/14.76 280/11.0
817-E6 52Kg/115lbs NB40/1½” 25 149/5.87 196/7.72 285/11.22 230/9.06 490/19.29 304/12.0
817-G7 75Kg/165lbs NB50/2” 46 200/7.87 248/9.76 420/16.54 350/13.78 620/20.41 368/14.5
PRODUCT OPTIONS
Stainless Steel bodies and cartridges for a wider range of
fluids such as Water, Steam, Oxygen, & Nitric Acid
Stainless Steel cartridges in manifolds for 400 bar systems Viton seals for operation at higher temperatures
sales@dynamiccontrols.co.uk T: +44 (0) 161 633 3933 sales@cunicocorp.com T: 562 733 4633
Rev. 7/31/14
23 of 27
24.
VALVE TECHNICAL DATA SHEET
SPRING LOADED PRESSURE REGULATOR 818
280 Bar 4000 psi
Technical Data
Design Specification Based on NES 375/ MIL-V-2961
Working Pressure 280 Bar / 4000 psi
Working Temperature Min –20ºC/-4ºF Max 120ºC/250ºF
Medium Air, Nitrogen, Helium, Oxygen. Hydraulic Fluid.
Quality Assurance Level En 10204, 3.1b also Full traceability – MIC Level 1
Cleaning TP102, Oxygen cleaning to MIL-STD-1330
Hydrostatic Test 420 Bar / 6000psi (High pressure and low pressure sides)
Ranges Available 8 bands ranging form 1 bar (7.5 psi) to 370 bar (5365 psi)
Shock Qualification MIL-S-901D
Vibration Qualification MIL-STD-167-1
Maximum Lock-up Pressure >7 bar set point: Set point plus 10%, <7 bar Set point: 2 bar
Minimum Droop Pressure >7 bar set point: Set point minus 10%, <7 bar Set point: 2 bar
Housing Material 70/30 Copper Nickel to NES 780 Pt2, class 1/ASTM B151
Main Cartridge Components Material Nickel aluminium bronze to NES 833 part 2 /ASTM B150
Seals Material HNBR/ Fluorocarbon
Seat Material PEEK virgin FL350
Nuts/Studs Material Stainless Steel NES 862/ASME 194/ASME 193 MIL-S-1222
Connection Type Cartridge flanged to housing or manifold.
Housing welded or screwed (to be specified)
OVERALL DIMENSIONS (CARTRIDGE AND HOUSING)
Product
Designation
Estimated
Weight
Pipe Size
Cv
A
(mm/ins)
B
(mm/ins)
C
(mm/ins)
D
(mm/ins)
H
(mm/ins)
L
(mm/ins)
818-A2 4Kg/8.8lbs NB15/½” 1.5 20/0.79 110/4.33 125/4.9 60/2.36 240/9.45 215/8.46
818-B3 7Kg/15.4lbs NB20/¾” 4 28/1.1 118/4.65 145/5.71 73/2.87 250/9.84 228/8.98
818-C4 12Kg/26.4lbs NB25/1” 7 35/1.38 125/4.92 190/7.48 89/3.5 332/13.07 254/10.0
818-D5 30Kg/66lbs NB32/1¼” 12 75/2.95 165/6.5 250/9.84 109/4.29 414/16.3 280/11.0
818-E6 52Kg/115lbs NB40/1½” 25 130/5.12 220/8.66 285/11.22 140/5.51 554/21.81 304/12.0
818-G7 75Kg/165lbs NB50/2” 46 192/7.56 282/11.1 420/16.54 200/7.87 705/27.76 368/14.5
PRODUCT OPTIONS
Stainless Steel bodies and cartridges for a wider range of
fluids such as Water, Steam, Oxygen, & Nitric Acid
Stainless Steel cartridges in manifolds for 280 bar systems Viton seals for operation at higher temperatures
sales@dynamiccontrols.co.uk T: +44 (0) 161 633 3933 sales@cunicocorp.com T: 562 733 4633
Rev. 7/31/14
24 of 27
25.
VALVE TECHNICAL DATA SHEET
SPRING LOADED PRESSURE REGULATOR 818
400 Bar 6000 psi
Technical Data
Design Specification Based on NES 375/ MIL-V-2961
Working Pressure 400 Bar / 6000 psi
Working Temperature Min –20ºC/-4ºF Max 120ºC/250ºF
Medium Air, Nitrogen, Helium, Oxygen. Hydraulic Fluid.
Quality Assurance Level En 10204, 3.1b also Full traceability – MIC Level 1
Cleaning TP102, Oxygen cleaning to MIL-STD-1330
Hydrostatic Test 600 Bar / 9000psi (High pressure and low pressure sides)
Ranges Available 8 bands ranging form 1 bar (7.5 psi) to 370 bar (5365 psi)
Shock Qualification MIL-S-901D
Vibration Qualification MIL-STD-167-1
Maximum Lock-up Pressure >7 bar set point: Set point plus 10%, <7 bar Set point: 2 bar
Minimum Droop Pressure >7 bar set point: Set point minus 10%, <7 bar Set point: 2 bar
Housing Material 70/30 Copper Nickel to NES 780 Pt2, class 1/ASTM B151
Main Cartridge Components Material Nickel aluminium bronze to NES 833 part 2 /ASTM B150
Seals Material HNBR/ Fluorocarbon
Seat Material PEEK virgin FL350
Nuts/Studs Material Stainless Steel NES 862/ASME 194/ASME 193 MIL-S-1222
Connection Type Cartridge flanged to housing or manifold.
Housing welded or screwed (to be specified)
OVERALL DIMENSIONS (CARTRIDGE AND HOUSING)
Product
Designation
Estimated
Weight
Pipe Size
Cv
A
(mm/ins)
B
(mm/ins)
C
(mm/ins)
D
(mm/ins)
H
(mm/ins)
L
(mm/ins)
818-A2 4Kg/8.8lbs NB15/½” 1.5 20/0.79 110/4.33 125/4.9 60/2.36 240/9.45 215/8.46
818-B3 7Kg/15.4lbs NB20/¾” 4 28/1.1 118/4.65 145/5.71 73/2.87 250/9.84 228/8.98
818-C4 12Kg/26.4lbs NB25/1” 7 35/1.38 125/4.92 190/7.48 89/3.5 332/13.07 254/10.0
818-D5 30Kg/66lbs NB32/1¼” 12 75/2.95 165/6.5 250/9.84 109/4.29 414/16.3 280/11.0
818-E6 52Kg/115lbs NB40/1½” 25 130/5.12 220/8.66 285/11.22 140/5.51 554/21.81 304/12.0
818-G7 75Kg/165lbs NB50/2” 46 192/7.56 282/11.1 420/16.54 200/7.87 705/27.76 368/14.5
PRODUCT OPTIONS
Stainless Steel bodies and cartridges for a wider range of
fluids such as Water, Steam, Oxygen, & Nitric Acid
Stainless Steel cartridges in manifolds for 400 bar systems Viton seals for operation at higher temperatures
sales@dynamiccontrols.co.uk T: +44 (0) 161 633 3933 sales@cunicocorp.com T: 562 733 4633
Rev. 7/31/14
25 of 27
26.
VALVE TECHNICAL DATA SHEET
ELECTRICALLY ACTUATED STOP VALVE 821
280 Bar 4000 psi
Technical Data
Design Specification Based on NES 375/ MIL-V-24109
Working Pressure 280 Bar / 4000 psi
Working Temperature Min –20ºC/-4ºF Max 120ºC/250ºF
Medium Air, Nitrogen, Helium, Oxygen. Hydraulic Fluid.
Quality Assurance Level En 10204, 3.1b also Full traceability – MIC Level 1
Cleaning TP102, Oxygen cleaning to MIL-STD-1330
Hydrostatic Test 420 Bar / 6000psi (High pressure and low pressure sides)
Airtight Test 308 Bar/ 3400psi
Shock Qualification MIL-S-901D
Vibration Qualification MIL-STD-167-1
Leakage Class Bubble Tight as per ANSI Class VI
Housing Material 70/30 Copper Nickel to NES 780 Pt2, class 1/ASTM B151
Main Cartridge Components Material Nickel aluminium bronze to NES 833 part 2 /ASTM B150
Seals Material HNBR/ Fluorocarbon
Seat Material PEEK virgin FL350
Nuts/Studs Material Stainless Steel NES 862/ASME 194/ASME 193 MIL-S-1222
Handwheel Material Not Applicable
Connection Type Cartridge flanged to housing or manifold.
Housing welded or screwed (to be specified)
OVERALL DIMENSIONS (CARTRIDGE AND HOUSING)
Product
Designation
Estimated
Weight
Pipe Size
Cv
A
(mm/ins)
B
(mm/ins)
C
(mm/ins)
D
(mm/ins)
H
(mm/ins)
L
(mm/ins)
821-A2 4Kg/8.8lbs NB15/½” 6 21/0.8 97/3.8 295/11.6 64/2.5 287/11.3 215/8.46
821-B3 6.5Kg/14.3lb NB20/¾” 18 29/1.1 81/3.2 343/13.5 86/3.39 321/12.7 228/8.98
821-C4 11Kg/24.2lbs NB25/1” 36 70/2.8 85/3.3 370/24.7 112/4.41 342/13.5 254/10.0
821-D5 NB 32/ 1¼" On Request
821-E6 NB 40/ 1½" On Request
821-G7 NB 50/ 2" On Request
PRODUCT OPTIONS
Stainless Steel bodies and cartridges for a wider range of
fluids such as Water, Steam, Oxygen, & Nitric Acid
Actuator voltage: 24v DC, 110v AC, 240v AC
Provided with Manual Override Facility
Stainless Steel cartridges in manifolds for 280 bar systems Position Indicator Switches Provided
sales@dynamiccontrols.co.uk T: +44 (0) 161 633 3933 sales@cunicocorp.com T: 562 733 4633
Rev. 7/31/14
26 of 27
27. The Cartridge Principal
• Housings can be installed at a different time to that of the
cartridge valve.
• The housing becomes a permanent integral part of the
system.
• Each housing will accept the full range of cartridges only
the size of the cartridge being the limiting factor.
Cartridge Housing
• Each cartridge valve is fully retractable from the
housing
• All parts are fully accessible including the seat and
plug for easy maintenance.
• Seat construction is such that replacement is by a
simple one- touch clip arrangement.
Cartridge Stop Valve
• Cleaning and pressure testing of the system is
easily carried out before the installation of the
cartridge valve by the use of specially designed
flushing adapters and blanking covers.
• Common components have been used throughout
the entire range of cartridge valves ensuring that
the spares requirements are minimized.
Housing with Flushing
• The fastening of the cartridge to the housing has
been so arranged to ensure that the orientation of the
valve is always positioned correctly.
• The oblique (45° angle) pattern design gives a similar
flow characteristic to that of a full flow ball valve, yet
sealing is equivalent to that of a plug valve.
Housing and Cartridge Assembly
27 of 27
Rev. 7/31/14