Brief Talk on Static Routing Configuration Experiment Leading Cisco networking products distributor-3anetwork.com

1. Brief Talk on Static Routing Configuration Experiment
Our aim is to communicate between these four routes on this experiment, that is to say, can ping
each other.
We can see that, when all of the Routers are connected together, the same network segment
can visit each other, but how can we make the routing between different network segments that
can also access each other? That is static routing configuration. Someone may ask why not use the
dynamic routing protocol? Yes, when there are too many devices we would certainly consider
giving priority to the use of dynamic routing protocol configuration, because it would be more
convenient. However, we are now doing experiment just to master the skill. Here is the each
routing configurations for your reference.
All routes are using the "NM-4A / S" Interface
Router1
Router>en / / Enter into privilege mode
Router#conf t / / Enter into configuration mode
Router(config)#int s1/0 // Enter into the S1/0 router ports
Router(config-if)#ip add 192.168.1.1 255.255.255.0 // Configure the ip address to s1 / 0 port
Router(config-if)#clock rate 64000 // Configure the clock to 64000
Router(config-if)#no sh // Start the port
Router(config-if)#exit // Exit the s1 / 0 port
Router(config)#ip route 192.168.2.0 255.255.255.0 192.168.1.2 //Configure static routing
table for the router
Router(config)#ip route 192.168.3.0 255.255.255.0 192.168.1.2 // Configure static routing table
for the router
1

2. Router(config)#exit //Exit the configuration mode
Router2
Router>en
Router#conf t
Router(config)#int s1/0
Router(config-if)#ip add 192.168.1.2 255.255.255.0
Router(config-if)#clock rate 64000
Router(config-if)#no sh
Router(config-if)#exit
Router(config)#int s1/1
Router(config-if)#:ip add 192.168.2.1 255.255.255.0
Router(config-if)#:clock rate 64000
Router(config-if)#no sh
Router(config-if)#exit
Router(config)#ip route 192.168.3.0 255.255.255.0 192.168.2.2
Router(config)#exit
Router3
Router>en
Router#conf t
Router(config)#int s1/1
Router(config-if)#ip add 192.168.2.2 255.255.255.0
Router(config-if)#clock rate 64000
Router(config-if)#no sh
Router(config-if)#exit
Router(config)#int s1/0
Router(config-if)#ip add 192.168.3.1 255.255.255.0
Router(config-if)#clock rate 64000
Router(config-if)#no sh
Router(config-if)#exit
Router(config)#ip route 192.168.1.0 255.255.255.0 192.168.2.1
Router(config)#exit
Router4
Router>en
Router#conf t
Router(config)#int s1/0
Router(config-if)#ip add 192.168.3.1 255.255.255.0
Router(config-if)#clock rate 64000
2

3. Router(config-if)#no sh
Router(config-if)#exit
Router(config)#ip route 192.168.1.0 255.255.255.0 192.168.3.1
Router(config)#ip route 192.168.2.0 255.255.255.0 192.168.3.1
Router(config)#exit
After the completion of the final configuration, our four routers can visit each other. Now, our
experiment is basically completed.
More related:
About Configuring Cisco Router 2901 / Port Forwarding
See detailed Memory Configuration on Cisco 3925 Router
Stacking – WS-C3750G-24TS and X-series
Cisco 1941 vwic 2 port combine
More Cisco products and Reviews you can visit: http://www.3anetwork.com/blog
3Anetwork.com is a world leading Cisco networking products wholesaler, we wholesale
original new Cisco networking equipments, including Cisco Catalyst switches, Cisco
routers, Cisco firewalls, Cisco wireless products, Cisco modules and interface cards
products at competitive price and ship to worldwide.
Our website: http://www.3anetwork.com
Telephone: +852-3069-7733
Email: info@3Anetwork.com
Address: 23/F Lucky Plaza, 315-321 Lockhart Road, Wanchai, Hongkong
3