This document provides an overview and instructions for operating the BITUMAT B2, an automatic welder used to weld modified bitumen roofing sheets. The 7-section guide includes details on the product, operating instructions, resources, parts list, accessories, related products, and service support. Key aspects covered are the machine's controls and settings, power needs, how to prepare surfaces and test welds, and proper operating and shutdown procedures. Maintaining a clean machine is emphasized for maximizing performance and life.
Z-Series heated-roll flatwork ironers are designed to maximize productivity and quality for on-premise laundries. The ironers can finish linens in one pass without dryer conditioning and do not require messy wax application and removal. The ironers feature increased processing speeds over previous models of 40-50% and new burner systems for greater efficiency. Z-Series ironers are also durable, ergonomic, and include safety features.
This document discusses bitumen welding tools from Leister, including the BITUMAT hot-air welding machine. The BITUMAT allows for fast, safe, and clean welding of bitumen sheets using hot air rather than hazardous propane gas burners. It has consistent results, easy operation, high speed, adjustable settings, and enhanced safety features. The document also briefly mentions the TRIAC PID and TRIAC S hand tools and some accessories for bitumen welding.
Z-Series heated-roll flatwork ironers are designed to maximize productivity and quality for on-premise laundries. The ironers can finish linens in one pass without dryer conditioning and do not require messy wax application and removal. The ironers feature increased processing speeds over previous models of 40-50% and new burner systems for greater efficiency. Z-Series ironers are also durable, ergonomic, and include safety features.
This document discusses bitumen welding tools from Leister, including the BITUMAT hot-air welding machine. The BITUMAT allows for fast, safe, and clean welding of bitumen sheets using hot air rather than hazardous propane gas burners. It has consistent results, easy operation, high speed, adjustable settings, and enhanced safety features. The document also briefly mentions the TRIAC PID and TRIAC S hand tools and some accessories for bitumen welding.
This document provides specifications for a Cummins diesel generator set model SC240. It has a prime power rating of 220 kVA and standby power rating of 240 kVA. Key specifications include an 8.3L, 6-cylinder Cummins engine producing 200 kW of prime power. The generator has a Leroy Somer or Stamford alternator and is controlled by a ComAp AMF20 control panel. Standard features include a soundproof and weatherproof enclosure. Optional features include low fuel and battery monitoring, an automatic transfer switch, and a trailer mount.
1) The document describes a patented heat generator that meets European regulations. It includes a combustion chamber, fluid mixing chamber, safety devices, and electrical control panel.
2) An "ECOMIX" burner that meets gas directives is also described, including electronic flame control, gas valves, and modulating gas/air control.
3) Accessories for the system like radiating belts, flues, software, and installation materials are also listed.
This document summarizes the specifications of a diesel generator composed of a Cummins engine and Stamford alternator. The generator has a power output of 375-413 KVA at 50Hz. It features an automatic start function, optional weatherproof and soundproof canopy, and overspeed, overload and low oil pressure protections. The control panel is a Deep Sea DSE702 module that allows for engine control and generator protection functions.
This document provides specifications for a diesel generator composed of a Cummins engine and Leroy Somer alternator. The generator has a power output of 150-163 KVA at 50Hz and outputs 400/230V. It features an automatic start, optional weatherproof canopy, integrated steel base, and overspeed protection. The control panel is a Deep Sea DSE702 module that provides engine control and generator protection functions.
The document describes the manufacturing process of 500 MW turbo generator stator winding bars at BHEL Haridwar. It discusses the 8 blocks involved in manufacturing including the electrical machine block, fabrication block, and coil & insulation manufacturing block. Within the coil & insulation block, it details the various sections for assembling, winding stator bars, impregnation, and testing the completed bars including tan delta and high voltage tests before the bars are installed in the generator. It provides key technical specifications for the 500 MW turbo generators.
This document summarizes the specifications of a diesel generator including:
- Output of 440V/220V, 60Hz three phase power from a Cummins engine and STAMFORD alternator
- Standard features include an electric starter, water cooling, 8 hour fuel tank, and optional soundproofing
- Precise voltage regulation within ±0.5% under all load conditions
- High quality components including the engine, alternator, cooling system, electrical system, and exhaust
This document provides specifications for a Doosan SDO388 diesel generating set with an industrial range. It has a prime power rating of 347kVA and standby power rating of 388kVA. The set is powered by a Doosan P126TI-II engine that produces 307kW of prime power and 342kW of standby power. It has a Leroy Somer LSA46.2VL12 or Stamford HCI444D alternator. The generating set has a base mounted control panel and provides 480V/277V, 60Hz three phase power. It also includes standard features such as an auto start system, 8-hour run time fuel tank, and soundproof and weatherproof
This document summarizes the specifications of a diesel generator including:
- Output of 440V/220V, 60Hz three phase power from a Cummins engine and Leroy somer alternator
- Standard features include an electric starter, water cooling, 8 hour fuel tank, and optional weatherproof canopy
- Technical specifications include voltage regulation within ±0.5%, frequency adjustable from 0-100% load, and low frequency undulation
This document provides specifications for a diesel generating set model SC1000 powered by a Cummins engine. The generator set has a prime power rating of 900kVA/720kW and standby power rating of 1000kVA/800kW. Key specifications include an 1800rpm Cummins KTA38-G2 diesel engine, Leroy Somer or Stamford brushless alternator, 24V electric start, radiator cooling system, and a ComAp AMF20 control panel. Standard features include automatic mains failure protection, engine monitoring and protection, and voltage regulation within ±0.5%.
The Rittal Aisle Containment System is increasingly being deployed in Data Centres where the average power demand of each
cabinet exceeds 5kW. Effectively using roof panels and slideable doors at each end of the row which ‘contains’ the air within
the aisle. This prevents the cold and the hot air mixing which increases the capacity of the overall system to approx
10 kW per cabinet. The other benefit is that because the cold air is now being delivered directly to the server, the cold aisle air
temperature can be raised, this means the CRAC or Inline cooling (LCP Inline) system is a lot more energy efficient which
results in long-term energy cost savings.
Cold and hot air cannot mix, warm air does not flow into the cold aisle
The system can be operated with a much higher extracted air temperature.
Standard air circulation cooling units are operated at an optimum thermal efficency level
Key Components for Aisle Containment
The key components of containment (same for both hot aisle and cold aisle) system are very simple. Firstly you need to specify
the containment dimensions and secondly the cooling system required.
The containment system is made up of roof panels and end doors. The roof panels bridge across the aisle between the racks
and the aisle and doors then close off the aisle. The roof sections are specified on the width of the aisle and the width
of the rack that they need to be secured to. The end doors quite simply match the height of the rack.
The cooling system for cold aisle and hot aisle can either be CRAC or Inline cooling, both have their advantages and limitations.
With the focus on efficiency and energy savings, we recommend you to contact our specialist sales team to
specify and advise the best cooling solution not only for your application but also for your long term business needs
Este documento describe conceptos relacionados con anualidades y amortizaciones. Explica qué son las anualidades, los elementos que las componen como plazo, renta e intervalo de pago. Luego detalla cómo calcular el monto y valor actual de una anualidad, así como también la renta en función de estos valores. Por último, presenta ejemplos numéricos para ilustrar cómo aplicar estas fórmulas.
El documento habla sobre la importancia de los valores cívicos y la responsabilidad en la escuela. Se enfatiza el respeto a los demás, la tolerancia, ser buen compañero y cumplir con las obligaciones. También se menciona la importancia de aprender y aprobar, así como seguir las reglas durante las excursiones y hacerle caso a los profesores.
EnvisionTEC is a manufacturer of 3D printers and photosensitive resins for dental applications. They offer various 3D printer models suited for different needs, including orthodontic models, surgical guides, dentures, and more. The document provides specifications for their printer lines including build size, resolution, materials compatibility, and other details. It emphasizes the digital workflow and integration with dental CAD software for an end-to-end solution in dental labs and offices.
El documento resume los principales géneros y formatos de programación en la televisión actual, incluyendo ficción, telenovelas, series, películas, talk shows, informativos, deportes, concursos y programas infantiles. Explica que los géneros se mezclan y la programación se planifica pensando en las franjas horarias y audiencias objetivo. También habla sobre la importancia de la ficción serializada y las bibliotecas de contenido que constituyen la identidad de los canales.
This document provides an overview of OpenStack, an open-source cloud computing platform. It discusses OpenStack's components, development process using Gerrit, and integration testing. It also covers using Windows as a guest operating system in OpenStack with Hyper-V, including Windows Cloud-Init tools and supported Windows versions. Key OpenStack components that support Windows like Nova, Neutron, Cinder, and Manila are summarized.
Este documento describe la historia y prácticas de los phreakers. Los phreakers son personas con amplios conocimientos en telecomunicaciones que realizan actividades no autorizadas con teléfonos, como interceptar llamadas usando dispositivos como las "cajas azules" que generan tonos para engañar a los sistemas telefónicos. El documento analiza el origen de la palabra phreak y las técnicas usadas por los phreakers desde los años 70 hasta la actualidad cuando se adaptaron a la tecnología digital.
Jornada benefica de salud, deporte y culturaMetalLube
En nombre de la AFAD, aprovecho la oportunidad para anunciarle la celebración de ésta Jornada de Salud, Deporte y Cultura, animándole a asistir y participar en las actividades programadas, agradeciendo a patrocinadores, participantes y asistentes su implicación y apoyo con nuestra asociación, en la lucha contra las adicciones con la promoción del deporte y la salud.
This document provides specifications for a Cummins diesel generator set model SC240. It has a prime power rating of 220 kVA and standby power rating of 240 kVA. Key specifications include an 8.3L, 6-cylinder Cummins engine producing 200 kW of prime power. The generator has a Leroy Somer or Stamford alternator and is controlled by a ComAp AMF20 control panel. Standard features include a soundproof and weatherproof enclosure. Optional features include low fuel and battery monitoring, an automatic transfer switch, and a trailer mount.
1) The document describes a patented heat generator that meets European regulations. It includes a combustion chamber, fluid mixing chamber, safety devices, and electrical control panel.
2) An "ECOMIX" burner that meets gas directives is also described, including electronic flame control, gas valves, and modulating gas/air control.
3) Accessories for the system like radiating belts, flues, software, and installation materials are also listed.
This document summarizes the specifications of a diesel generator composed of a Cummins engine and Stamford alternator. The generator has a power output of 375-413 KVA at 50Hz. It features an automatic start function, optional weatherproof and soundproof canopy, and overspeed, overload and low oil pressure protections. The control panel is a Deep Sea DSE702 module that allows for engine control and generator protection functions.
This document provides specifications for a diesel generator composed of a Cummins engine and Leroy Somer alternator. The generator has a power output of 150-163 KVA at 50Hz and outputs 400/230V. It features an automatic start, optional weatherproof canopy, integrated steel base, and overspeed protection. The control panel is a Deep Sea DSE702 module that provides engine control and generator protection functions.
The document describes the manufacturing process of 500 MW turbo generator stator winding bars at BHEL Haridwar. It discusses the 8 blocks involved in manufacturing including the electrical machine block, fabrication block, and coil & insulation manufacturing block. Within the coil & insulation block, it details the various sections for assembling, winding stator bars, impregnation, and testing the completed bars including tan delta and high voltage tests before the bars are installed in the generator. It provides key technical specifications for the 500 MW turbo generators.
This document summarizes the specifications of a diesel generator including:
- Output of 440V/220V, 60Hz three phase power from a Cummins engine and STAMFORD alternator
- Standard features include an electric starter, water cooling, 8 hour fuel tank, and optional soundproofing
- Precise voltage regulation within ±0.5% under all load conditions
- High quality components including the engine, alternator, cooling system, electrical system, and exhaust
This document provides specifications for a Doosan SDO388 diesel generating set with an industrial range. It has a prime power rating of 347kVA and standby power rating of 388kVA. The set is powered by a Doosan P126TI-II engine that produces 307kW of prime power and 342kW of standby power. It has a Leroy Somer LSA46.2VL12 or Stamford HCI444D alternator. The generating set has a base mounted control panel and provides 480V/277V, 60Hz three phase power. It also includes standard features such as an auto start system, 8-hour run time fuel tank, and soundproof and weatherproof
This document summarizes the specifications of a diesel generator including:
- Output of 440V/220V, 60Hz three phase power from a Cummins engine and Leroy somer alternator
- Standard features include an electric starter, water cooling, 8 hour fuel tank, and optional weatherproof canopy
- Technical specifications include voltage regulation within ±0.5%, frequency adjustable from 0-100% load, and low frequency undulation
This document provides specifications for a diesel generating set model SC1000 powered by a Cummins engine. The generator set has a prime power rating of 900kVA/720kW and standby power rating of 1000kVA/800kW. Key specifications include an 1800rpm Cummins KTA38-G2 diesel engine, Leroy Somer or Stamford brushless alternator, 24V electric start, radiator cooling system, and a ComAp AMF20 control panel. Standard features include automatic mains failure protection, engine monitoring and protection, and voltage regulation within ±0.5%.
The Rittal Aisle Containment System is increasingly being deployed in Data Centres where the average power demand of each
cabinet exceeds 5kW. Effectively using roof panels and slideable doors at each end of the row which ‘contains’ the air within
the aisle. This prevents the cold and the hot air mixing which increases the capacity of the overall system to approx
10 kW per cabinet. The other benefit is that because the cold air is now being delivered directly to the server, the cold aisle air
temperature can be raised, this means the CRAC or Inline cooling (LCP Inline) system is a lot more energy efficient which
results in long-term energy cost savings.
Cold and hot air cannot mix, warm air does not flow into the cold aisle
The system can be operated with a much higher extracted air temperature.
Standard air circulation cooling units are operated at an optimum thermal efficency level
Key Components for Aisle Containment
The key components of containment (same for both hot aisle and cold aisle) system are very simple. Firstly you need to specify
the containment dimensions and secondly the cooling system required.
The containment system is made up of roof panels and end doors. The roof panels bridge across the aisle between the racks
and the aisle and doors then close off the aisle. The roof sections are specified on the width of the aisle and the width
of the rack that they need to be secured to. The end doors quite simply match the height of the rack.
The cooling system for cold aisle and hot aisle can either be CRAC or Inline cooling, both have their advantages and limitations.
With the focus on efficiency and energy savings, we recommend you to contact our specialist sales team to
specify and advise the best cooling solution not only for your application but also for your long term business needs
Este documento describe conceptos relacionados con anualidades y amortizaciones. Explica qué son las anualidades, los elementos que las componen como plazo, renta e intervalo de pago. Luego detalla cómo calcular el monto y valor actual de una anualidad, así como también la renta en función de estos valores. Por último, presenta ejemplos numéricos para ilustrar cómo aplicar estas fórmulas.
El documento habla sobre la importancia de los valores cívicos y la responsabilidad en la escuela. Se enfatiza el respeto a los demás, la tolerancia, ser buen compañero y cumplir con las obligaciones. También se menciona la importancia de aprender y aprobar, así como seguir las reglas durante las excursiones y hacerle caso a los profesores.
EnvisionTEC is a manufacturer of 3D printers and photosensitive resins for dental applications. They offer various 3D printer models suited for different needs, including orthodontic models, surgical guides, dentures, and more. The document provides specifications for their printer lines including build size, resolution, materials compatibility, and other details. It emphasizes the digital workflow and integration with dental CAD software for an end-to-end solution in dental labs and offices.
El documento resume los principales géneros y formatos de programación en la televisión actual, incluyendo ficción, telenovelas, series, películas, talk shows, informativos, deportes, concursos y programas infantiles. Explica que los géneros se mezclan y la programación se planifica pensando en las franjas horarias y audiencias objetivo. También habla sobre la importancia de la ficción serializada y las bibliotecas de contenido que constituyen la identidad de los canales.
This document provides an overview of OpenStack, an open-source cloud computing platform. It discusses OpenStack's components, development process using Gerrit, and integration testing. It also covers using Windows as a guest operating system in OpenStack with Hyper-V, including Windows Cloud-Init tools and supported Windows versions. Key OpenStack components that support Windows like Nova, Neutron, Cinder, and Manila are summarized.
Este documento describe la historia y prácticas de los phreakers. Los phreakers son personas con amplios conocimientos en telecomunicaciones que realizan actividades no autorizadas con teléfonos, como interceptar llamadas usando dispositivos como las "cajas azules" que generan tonos para engañar a los sistemas telefónicos. El documento analiza el origen de la palabra phreak y las técnicas usadas por los phreakers desde los años 70 hasta la actualidad cuando se adaptaron a la tecnología digital.
Jornada benefica de salud, deporte y culturaMetalLube
En nombre de la AFAD, aprovecho la oportunidad para anunciarle la celebración de ésta Jornada de Salud, Deporte y Cultura, animándole a asistir y participar en las actividades programadas, agradeciendo a patrocinadores, participantes y asistentes su implicación y apoyo con nuestra asociación, en la lucha contra las adicciones con la promoción del deporte y la salud.
Este es un articulo que analiza el impacto de las ideas de Disney fundador del fenómeno recreativo Disneylandia y cómo esta idea se convirtió en el paradigma de diseño de las grandes creativas. Se discute los aspectos positivos y negativos de esta nueva doctrina de diseño urbanístico.
Introduction to JVM languages and Fantom (very brief)Jonathan Holloway
JVM languages provide more expressiveness and help modernize programming languages. Fantom is a JVM language that compiles to JVM, CLR, and JavaScript. It is a multi-paradigm language that supports object-oriented, functional, static and dynamic typing. Fantom aims to reduce boilerplate code through features like mixins, concise accessors, null-safe fields, and closures. It also provides actor-based concurrency and foreign function interfaces.
Bhushan Salgar is seeking employment as an IT Manager or Project Leader with over 12 years of experience in the IT industry. He has extensive experience successfully implementing several SAP ERP projects in India and internationally. He is skilled in areas such as project planning, data warehouse design, software development, and user training. Some of his key projects involved implementing SAP systems, migrating applications to new database versions, and designing and developing data warehouses.
Este documento describe un proyecto para crear una base de datos abierta de las rutas de transporte público en la Ciudad de México a través de la participación ciudadana y el uso estratégico de la tecnología. Un equipo formado por el gobierno y organizaciones civiles realizó una prueba piloto mapeando rutas en dos estaciones de autobuses y desarrolló una herramienta tecnológica. El objetivo final es publicar los datos mapeados para mejorar la toma de decisiones y políticas públicas relacionadas con la
iMeeting: implementación de instrumentos financieros (Jeremie)Agencia IDEA
El documento describe la experiencia de implementación del Fondo Jeremie Andalucía, un instrumento financiero creado para abordar las brechas de financiación de las empresas en Andalucía. El fondo movilizó 185 millones de euros para apoyar proyectos empresariales a través de intermediarios financieros. Se explican los desafíos de cambiar la mentalidad del sector público y privado para adoptar este nuevo modelo de financiación basado en instrumentos financieros en lugar de subvenciones. El fondo ha logrado aprobar 550 proyectos con una in
Registro fotográfico y clasificación de las antenas del estado laraArgimiro Gutierrez
El documento presenta información sobre 8 sistemas de antenas parabólicas y de radiofrecuencia ubicadas en Venezuela. Para cada sistema se proporciona la frecuencia de operación, ubicación, coordenadas geográficas y la empresa propietaria. Los sistemas son usados para recibir y transmitir señales de radio, telefonía y televisión.
Estrategia de gestión sostenible del territorio rural remurpe sansalvadorDuriel Pérez Román
El documento describe la estrategia de gestión sostenible del territorio rural en el distrito de San Salvador. El distrito tiene altos niveles de pobreza y carece de servicios básicos como agua potable y saneamiento. La estrategia incluye inversiones en obras de infraestructura de agua y saneamiento, educación sanitaria y capacitación para lograr la participación comunitaria y sostenibilidad de los servicios.
El documento es un examen final sobre el lenguaje de programación Pascal. Contiene preguntas sobre la definición de Pascal, los parámetros utilizados, los ciclos comunes como for, y las funciones de texto.
1. DIKE, Abogados SCP ofrece una amplia gama de servicios legales y de asesoría empresarial de forma integral a través de Internet, cubriendo derecho mercantil, fiscal, laboral, civil y penal.
2. El bufete está formado por un equipo de especialistas en cada área del derecho que ofrecen un trato personalizado y soluciones efectivas a empresas, autónomos y particulares de forma remota a través de Internet y teléfono.
3. El objetivo es aprovechar las ventajas de Internet para prestar la mayor
Este documento presenta el certificado de eficiencia energética de un edificio existente. Incluye la identificación del edificio, los datos del técnico certificador, la calificación energética obtenida y cuatro anexos que describen las características energéticas del edificio, la calificación energética detallada, recomendaciones para la mejora de la eficiencia y las pruebas realizadas por el técnico certificador.
Stands built for international exhibitorssukanya13
The document discusses the benefits of exercise for mental health. Regular physical activity can help reduce anxiety and depression and improve mood and cognitive function. Exercise causes chemical changes in the brain that may help protect against mental illness and improve symptoms.
This document provides instructions for building a permanent magnet generator (PMG) in 3 sentences or less:
The document outlines the materials, tools, and steps required to construct a PMG, including constructing jigs and molds for winding coils and positioning magnets, building the stator and rotor assemblies, and testing and connecting the PMG to produce electricity from wind or water power. Detailed diagrams and explanations are provided for each part and construction process to enable someone to build their own small-scale renewable energy generator. Safety precautions are also noted, as the magnets in the PMG can become loose and damage the device if not properly assembled and operated.
The document provides safety rules, start up procedures, specifications, and operating instructions for a CNC wire-cut machine. It details ensuring safety, wearing proper protective equipment, starting the machine correctly, setting parameters like wire tension and feed, and basic maintenance after use. Edge finding and center finding functions are described to accurately set up and position workpieces.
This document summarizes the specifications of a welding generator. It is a double-function machine that can weld and generate power. It uses a YANMAR engine and produces stable welds. The generator provides single or three-phase AC power and has features like adjustable welding current, low noise, and safety mechanisms. Specifications include voltage, power output, engine details, fuel capacity, and dimensions for various models from 10.7kW to 40.8kW.
This document provides information on LG's commercial air conditioner solutions, focusing on their smart inverter single central air conditioning (CAC) units. It highlights key benefits including energy savings of up to 22% compared to constant speed models, intelligent features like human detection and wireless control via LG ThinQ, and reliability elements such as corrosion resistance. A variety of indoor unit types are also presented, including 1 way and 4 way ceiling cassette units, ceiling concealed duct units, and floor standing units. Product lineups by capacity are shown, ranging from 9,000 to 60,000 BTU for single phase units and 30,000 to 100,000 BTU for 3 phase units.
Applimotion ho series_slotless_motors_datasheetElectromate
The document introduces the HO series NEMA 23 brushless motors from Applimotion for precision direct drive applications. The motors feature a large through hole, NEMA 23 mounting flange, high performance magnets, and optional windings. They provide sinusoidal torque curves, high resolution encoders up to 29 million counts per revolution, and are designed to replace geared mechanical stages for better accuracy and reliability. Key specifications for motor model 63-B-44-A are listed.
This document provides an erection manual for a 500 MW steam turbine (KWU design) produced by Bharat Heavy Electricals Limited (BHEL). It includes technical data on the turbine specifications, construction details, operating parameters including steam pressures, speeds, temperatures and limitations. The manual aims to establish uniform erection practices to improve quality and reduce time and costs for site erection activities. Various instruction sheets provide guidelines on handling, erection sequence, procedures, grouting, piping and other critical activities.
This document provides specifications for a SMI2500 diesel generating set powered by a Mitsubishi engine. It can generate 2273 kVA of prime power or 2500 kVA of standby power. The set consists of a 4-stroke, 16-cylinder Mitsubishi engine coupled to a Leroy Somer or Stamford alternator. It has a base control panel and optional features include soundproofing, low fuel alarms, and an automatic transfer switch. Standard voltages are 480/277V at 60Hz but other voltages are available.
Focus on SMT machine manufacturing&offering comprehensive solution in bulk LED assemble.Provide high quality replacement parts.Machine installation,repair,maintenance,Pre-sales and after sales service.
This document provides technical data for the erection of a 500 MW steam turbine from KWU design. It includes specifications for the turbine construction including cylinders, valves, speeds, pressures, temperatures, and limitations. Key details include it being a three cylinder reheat condensing turbine with 17 reaction stages in the high pressure cylinder and 12 reaction stages per flow in the double flow intermediate pressure cylinder. The rated steam conditions and permissible operating values are also provided.
MULTI V 5 Catalogue_Small[20231107_182247769].pdfAnkitavaghela5
LG has been a leading manufacturer of air conditioners since 1968 in Korea and globally. It produces efficient and high-quality products across various categories through R&D and manufacturing facilities in India. LG offers comprehensive training and tools to support HVAC professionals and provides customized solutions for different customer needs including energy efficiency, space utilization, and smart building capabilities.
The document describes an inverter based welding machine company called S.R. ELECTRICAL Co. It lists 13 different inverter welding machine models for arc, TIG, and plasma cutting welding. It provides details on the specifications, features, and parameters of some of the machine models including the ARC series inverter DC arc welding machines, WS inverter DC TIG welding machines, and NBC inverter CO2 gas shielded welding machines. The machines listed use IGBT or MOSFET inverter technology and have features like compact design, energy efficiency, and protective circuits for safe operation.
This document provides parts lists and operating instructions for the KBM-28U inverted portable plate edge bevelling machine. It can produce bevel angles from 22.5 to 55 degrees and has adjustable components to accommodate different bevel sizes. The document outlines machine specifications, safety guidelines for lifting and electrical connections, maintenance procedures, and parts breakdown diagrams to support operation and repairs.
Find out more about Infineon on our Homepage: www.infineon.com
Power semiconductors play a key role to produce energy from renewable sources.
In wind turbines, power semiconductors are used to convert power and to couple
the generator with the grid. Find out here more about Solutions for Wind Energy Sysytems powered by Infineon.
This document provides information on various antenna rotators and controllers from Hy-Gain. It describes the key specifications of the Tailtwister T2X and HDR-300A rotators, including their wind load capacity, turning power, brake power, and other technical details. It also provides ordering information and prices for the rotators, as well as for various digital controllers like the DCU-1, DCU-2, and DCU-3 that can be used with the rotators. Additional rotators and controllers described include the HAM-IV, AR-40, CD-45II, and replacement parts.
This document introduces the HO series NEMA 23 brushless motors from Applimotion for direct drive rotary applications. The motors have a large through hole, NEMA 23 mounting flange, and high performance magnets. They offer high resolution encoder options, sinusoidal torque curves, and are designed to replace geared mechanical stages for better accuracy and reliability. Key specifications are provided for motor torque, speed, current, resistance, weight and dimensions.
Dr. Mike Brumm - Owner's Manual For Your Your Hog BarnJohn Blue
Owner's Manual For Your Your Hog Barn - Dr. Mike Brumm - Brumm Swine Consultancy, Inc., Minnesota, from the 2013 Missouri Pork Expo, February 13 - 14, 2013, Columbia, MO, USA.
More presentations at http://www.swinecast.com/2013-missouri-pork-expo
The ePropelled SG6000 starter generator is designed for UAV applications. It has a slim, lightweight design with active air cooling that allows it to operate up to 180°C. It uses a patent-pending bearingless mounting system and has high power density. Specifications include a diameter of 7.32 inches, weight of 5.4 pounds, and peak power output of 8% below its rated maximum continuous power for 5 minutes. It requires consistent airflow of at least 2m/s to maintain performance levels.
The document provides technical specifications for erecting a 500 MW steam turbine from KWU design, including:
- It is a three cylinder reheat condensing turbine with a single flow HP turbine, double flow IP turbine, and double flow LP turbine.
- It has main stop and control valves, reheat stop and control valves, and extraction swing check valves.
- The rated speed is 50.0 revolutions per second and the maximum under valve wide open condition is 524.2 MW.
4. Product Details
Leisterʼs BITUMAT B2 is designed to weld modified bitumen
roofing sheets (SBS, APP).
This automatic welder is safer than traditional welding
torches because it uses hot air to heat the bitumen, not an
open flame, decreasing the risk of fire.
It is also more efficient because it only requires one
operator—unlike open-flame torches where two operators
are needed—helping to keep your workforce more
productive.
The BITUMAT B2 is the only bitumen welder that makes granular-to-granular welding
possible. The BITUMAT B2 produces so much heat that the bitumen liquifies, melting the
granular surface into the material before the two pieces are firmly pressed together to create
a strong weld.
4 888-785-4485
5. Call for a Quote
888-785-4485
Product
Details
The BITUMAT B2 offers the following features and
benefits:
• Flame-free welding of modified bitumen.
• Peel and shear strengths up to 3 times stronger than
flame welding.
• Easy control of hot-air volume.
• High working speed.
• Air dam to contain and centralize hot air over the
weld.
• Adjustable guide bar to prevent back strain.
• Requires only one operator.
No matter the thickness, type of surface finish, operator or weather conditions, the
BITUMAT B2 produces consistent, repeatable seam welds on any modified bitumen roofing
system.
5 888-785-4485
6. Call for a Quote
888-785-4485
Product
Details
Voltage V~ 230
Power consumption W 6,700
Temperature oF 68 - 1,202
Speed ft./min. 2.6 - 39.4
Noise Emission LpA dB 73
Size (L x W x H) in. 27.2 x 19.3 x 13
88.2
Weight lbs.
(with cord)
The table to the right shows the Approval mark
BITUMAT B2 specifications.
Protection class I
140.436—3 in. nozzle
Order number
138.386—4 in. nozzle
6 888-785-4485
7. Product
Details
Device Overview
1. Power supply cord 18. Power cord holder
2. Housing 19. Guide roller
3. Main power switch 20. Adjusting screw—Guide roller
4. Drive switch 21. Adjusting sleeve
5. Speed knob 22. Replacement drive roller
6. Temperature knob 23. Screw-on additional weight
7. Welding nozzle 24. Screw for welding nozzle adjustment
8. Hot-air blower (ELECTRON) 25. Scraper
9. Tool holder 26. Screw for scraper
10. Locking lever 27. Holder for replacement drive roller
11. Transport roller 28. Carry handle
12. Scale for tool adjustment 29. Screw for adjusting sleeve
13. Drive roller 30. Fastening screw for welding nozzle
14. Fastening screw 31. Stainless steel wire brush
15. Lower guide bar 32. Knob for air volume
16. Clamping lever—Upper guide bar 33. Upper guide bar
17. Clamping screw—Lower guide bar
7 888-785-4485
9. Operating Instructions
This section offers an overview of the
BITUMAT B2ʼs controls and settings, and
instructions on how to properly set up and
operate the automatic welder.
Prior to starting, read through the
manufacturerʼs warnings and cautions listed
on page 60. If you have any questions or
need clarification, please contact IHSʼ
authorized Leister service center at
888-785-4485.
9 888-785-4485
10. Operating
Instructions
Controls
Welding Temperature—Red Dial—Controls the heat output on a 1-to-10 scale—all
temperatures are approximates. Settings 9 and 10 should only be used on material 180
mils or thicker.
Setting 0 1 2 3 4 5 6 7 8 9 10
°F Ambient 185 298 411 524 637 750 863 979 1,092 1,201
* Assumes air volume is set to maximum.
Welding Speed—Black Dial—Controls the speed of the machine on a 1-to-8 scale—all
speeds are approximates and based on attainable speeds while welding.
Setting 1 2 3 4 5 6 7 8
ft./min. 2.6 6.2 9.8 13.4 17 20.62 24.2 27.8
* The BITUMAT B2 is capable of reaching speeds of 39 ft./min., but tops out between 27 and 30 ft./min. during the welding process. In ideal welding
conditions, speed should be set to approximately 17 ft./min. to ensure adequate heat is applied to the seam.
10
23 888-785-4485
11. Operating
Instructions
Drive Switch—Black Switch—Activates the drive motor, which
moves the machine forward.
Power Switch—Orange Dial with Yellow Base—Turns the machine
on and off.
Air Volume—Black Dial on the Back of the Hot-Air Blower—
Controls the amount of air blowing through the heat gun. Air volume
setting ranges between 100% (maximum) and 75% (minimum).
NOTE: If the temperature is higher than setting 8, air volume must be
set to maximum, otherwise you run the risk of overheating the machine.
Pressure—Drive roller, silver weight and replacement drive roller
located at the front of the machine—Applies joining force to the
heated bitumen seam.
11 888-785-4485
12. Operating
Instructions
Power Needs
Generator (minimum requirements)
For the BITUMAT B2 to function properly, it • 6,700 watts, continuous power
needs to have a consistent, adequate power • 230 volts
source. Following are power requirements for • 30 amps
generators, wall outlets and extension cords. • Single phase
Wall Outlet (minimum requirements)
• 6700 watts
• 230 volts
• 30 amps
• Single phase
Extension Cord
• 10-3 gauge wire or lower
• 100-foot cord length (maximum)
12
23 888-785-4485
13. Operating
Instructions
How to Prepare the Surface and Machine
1. Clean the overlapped bitumen sheets of debris and
contaminants, like moisture, grease and oil.
NOTE: When welding granular-to-granular sheets with the
BITUMAT B2, you do not need to degranulate.
2. Set the guide bar to a comfortable position.
• Lower Guide Bar Clamping Screw—Adjusts Guide Bar
Angle—Loosen the clamping screw and tilt the guide bar
back to the desired position, and then retighten.
• Upper Guide Bar Clamping Lever—Lengthens or Shortens Clamping
Clamping
Lever
Guide Bar—Release the clamping lever and move the guide Screw
bar up or down to the desired height.
13
23 888-785-4485
14. Operating
Instructions
3. With an aerosol can of silicone, spray any part of the
machine that may be exposed to splattering bitumen,
including:
• Hot-air blower
• Nozzle tube (not the flat nozzle end)
• Undercarriage
• Drive roller
• Air dam and guide wheels
• Hot-air blower slide bar
This silicone will serve as a buffer between the melted bitumen
and the machineʼs surfaces, making it easier to clean. Make
sure to complete step before turning the machine on, as
the aerosol spray is flammable.
14 888-785-4485
15. Operating
Instructions
4. Plug the power cord into the power source outlet.
5. Snap the cord clip onto the cord holder to ensure the cord doesnʼt get entangled in
the machine.
6. Turn the machine on with the power switch.
7. Using the temperature, speed and air volume dials, configure the BITUMAT B2
according to the jobʼs requirements (see pg. 10 and 11 for settings).
Power Main Control
Cord Clip Switch Settings
15
22 888-785-4485
16. Operating
Instructions
NOTE: The BITUMAT B2 will take approximately 3-4
minutes to reach the proper welding temperature.
8. After the welder has warmed up, run a test weld (see
pg. 17 for details) on scrap material to make sure the
temperature, speed and air-volume settings are
properly configured for the job.
9. If the test weld does not meet your standards, make
any necessary adjustments to the machineʼs settings
before moving on.
16 888-785-4485
17. Operating
Instructions
How to Test Weld Quality
BITUMAT B2 heat output can be affected by an improper
balance of temperature, speed, air volume and pressure, as well
as external factors, such as moisture, humidity, ambient
temperature and direct sunlight.
For this reason, before every use, always run a test weld on
scrap material to make sure you have the proper settings. To
perform a test weld:
1. Cut two, 10-foot strips of bitumen sheeting.
2. With the configured and warmed-up BITUMAT B2, weld the
two strips together.
(conʼt on next page)
17
22 888-785-4485
18. Operating
Instructions
A good weld should produce a bead of bitumen along the edge of the seam.
3. Using a hook-blade, cut three-to-five 2-inch strips perpendicular to the seam. Strips should
be cut from the beginning, middle and end of the test weld to ensure quality throughout.
4. As soon as the bitumen surface over the seam weld is the same temperature as the rest of
the material surface, tear the strips apart.
A quality weld should reveal the scrim, or netting, of the bitumen material.
Hook Blade
Bitumen Bead Test Strips
Bitumen Scrim
18
22
23 888-785-4485
19. Operating
Instructions
(Instructions continued from pg. 16)
10. When satisfied with the test weld, position your
properly configured BITUMAT B2 on top of the
bitumen seam.
Guide Roller
• Swing the guide roller down and align it with the
seam edge.
• Align the drive roller with the seam edge, but
place it approximately 3/8-inch off the edge. This
will help to keep the roller clean.
3/8 in. Gap
19
22
23 888-785-4485
20. Operating
Instructions
11. Stand in the welding position—behind
the BITUMAT B2 with the guide bar Not Engaged
directly in front of you.
12. Engage the lifting device (see pg. 27 for
details) by pushing the handle away Push Handle
from you. This will pick the drive roller Away
up off the bitumen sheet. Engaged
13. Turn on the drive switch to start the drive roller. The machine
will not begin moving as long as the lifting wheel is engaged.
20
22
23 888-785-4485
21. Operating
Instructions
14. Pull up on the locking lever, lower the hot-air blower, and slide the nozzle between
the overlapped bitumen.
Lowered Blower
Nozzle
Locking Lever
15. Count to three and then pull back on the lifting wheel Pull Back
lever. The machine will begin moving right away, so make
sure to have a firm grip on the guide bar.
21
22
23 888-785-4485
22. Operating
Instructions
16. Guide the BITUMAT B2 along the seam edge using
the guide bar.
NOTES:
• Do not push or pull the machine. Simply steer it so
the guide roller tracks the seam edge.
• Remember to keep the drive roller approximately 3/8-
inch off the seam edge to avoid melted bitumen
sticking to it.
• Keep the nozzle completely between the overlapped
bitumen. If the nozzleʼs air holes are exposed they
will spray melted bitumen on the machine, material
surface, and potentially your clothes and skin.
22
23 888-785-4485
23. Operating
Instructions
17. At the end of the weld, immediately pull up on the locking lever, slide the hot-air
blower away from the machine, and then swivel it up into locked position.
Pull Locking Slide Hot-Air
Lever Blower Out
Swivel Up
Turn Off Drive Roller
18. Press in the drive switch to stop the drive roller.
22
23 888-785-4485
24. Operating
Instructions
How to Shut Down the BITUMAT B2
When your job is complete, follow these simple instructions to turn off the machine.
1. Turn the temperature dial to 0 and turn the air volume dial to maximum. The airflow
will gradually cool down the heating element, which will help to keep it in peak
working condition.
Turn Clockwise
Turn to 0 to Maximum
24
22
23 888-785-4485
25. Operating
Instructions
How to Shut Down the BITUMAT B2
2. While the heating element is cooling, but the nozzle is still hot, use a stainless steel
wire brush and scrape off any melted-on bitumen (see instructions on pg. 37). Be sure
to wear gloves and goggles.
NOTE: This is an important step because a buildup of
bitumen on the nozzle can restrict airflow (see image at
right), which will impact the machineʼs performance and
cause it to overheat.
3. Wipe any splattered bitumen off the BITUMAT B2 with a
rag and silicone spray.
4. Once clean, re-silicone all moving parts to keep them
lubricated. Clogged Nozzle
The key to maximizing the life of your welder is to keep it as clean as possible.
25
22
23 888-785-4485
26. Operating
Instructions
How to Shut Down the BITUMAT B2
5. Once the machine is blowing cool air (approximately 3-5 minutes), it
is safe to power it off using the main power switch.
6. Unplug the machine from the power source.
7. Move the BITUMAT B2 safely into its storage case.
Turn Power Off
Store Machine
In Case
26
22
23 888-785-4485
27. Operating
Instructions
About the Lifting Device
The BITUMAT B2 Lifting Device raises the drive roller off
the bitumen material. This important feature serves two
purposes:
• Allows the drive roller time to get up to speed once Lifting Device
started, instead of it gradually speeding up during a weld.
• Removes the machine weight from the seam edge, so
you can easily slide the nozzle between the material.
27
22
23 888-785-4485
29. Resources
This section provides maintenance tips and how-tos that will
help you keep your BITUMAT B2 in proper working order, and
prolong the life of the machine.
• How To: Change a heating element (pg. 30)
• How To: Change a nozzle (pg. 32)
• How To: Change the drive roller (pg. 34)
• How To: Clean a nozzle (pg. 37)
• How To: Clean a drive roller (pg. 38)
• How To: Install a lifting device (pg. 39)
• Troubleshoot: Poor weld quality (pg. 41)
WARNING: Do not perform any maintenance on the BITUMAT B2 while it is plugged in,
unless otherwise noted.
29 888-785-4485
30. Resources:
How To
Loosen Cheese-
Change a Heating Element Head Screws
Over time and with frequent use, the BITUMAT B2ʼs heating
element will wear down and possibly break. When this occurs, it
needs to be replaced.
Following are simple steps to replace your BITUMAT B2 heating
element. (See pg. 53 for the heating element order number.) Pull Off
Nozzle
NOTE: Allow the BITUMAT B2 nozzle to cool before starting this
process.
1. Remove the four cheese-head screws that hold the nozzle to
the hot-air blower.
2. Pull the nozzle away from the handle.
30 888-785-4485
31. Resources:
How To
3. Slide the mica tube off the element. Slide Mica
4. Unscrew the grounding ring from the handle and slide it off the Tube Off
heating element.
5. Wiggle the heating element back and forth until it comes off.
6. Attach the new element by aligning the three pins with the three
sockets of the handle base. The element only attaches one way.
7. Reassemble the hot-air blower.
Unscrew Remove
Grounding Ring Element
Align Reassemble the
Element Pins Hot-Air Blower
31 888-785-4485
32. Resources:
How To
Loosen Cheese-
Head Screws
Change a Nozzle
Remove
Nozzles can get clogged with bitumen, dent or break, Nozzle
rendering them ineffective or useless. Following are
instructions on how to remove a nozzle and attach a
new one.
To remove a nozzle:
1. Unscrew the four cheese-head screws that
connect the handle to the nozzle.
2. Slide the nozzle over the mica tube and off the
hot-air blower.
32 888-785-4485
33. Resources:
How To
To attach a new nozzle:
1. Align the nozzle so that the flat base that slides between the bitumen sheets lays flat
against the ground when the hot-air blower is lowered.
2. Slide the new nozzle over the mica tube and align the holes with the screw holes on
the handle.
3. Insert and tighten the four cheese-head screws.
Slide Nozzle Tighten Cheese-
Lay Nozzle Flat
Over Mica Tube Head Screws
33 888-785-4485
34. Resources:
How To
Change the Drive Roller Unscrew Weight
As the BITUMAT B2 welds a bitumen seam, there is a good chance
that the drive roller will be exposed to melted bitumen (For cleaning
instructions see pg. 38). If this builds up, it can cause the wheel to
lay unevenly against the material surface leading to a poor weld.
The BITUMAT B2 comes with a spare drive roller, which is Remove Extra
stored under the circular weight at the front of the machine Drive Roller
(opposite the guide bar). To attach this new drive roller, follow these
instructions:
1. Unscrew the weight from the front of the machine.
2. Pull the new guide roller out of its holder. Lay Machine Flat
3. Place the welder on its side so that the hot-air blower faces up.
34 888-785-4485
35. Resources:
How To
4. Unscrew the brass fastening screw by turning counter-
clockwise, and remove.
5. Pull the air dam off the deflector roller.
6. Pull the drive roller up and off the machine, and then pull the air
dam off the roller.
7. Lay the air dam into the groove of the new drive roller.
Unscrew Brass
8. Align the new drive roller with the post on the machine, and slide Fastening Screw
it into position.
Lay Air Dam in Slide Drive Roller
Groove Into Position
Remove Drive
Pull Off Air Dam Roller
35 888-785-4485
36. Resources:
How To
9. Pull the air dam back over the deflector roller and make sure it lies completely in
the groove.
10. Insert the brass fastening screw through the middle of the drive roller and tighten
until snug.
11. Make sure the air dam aligns with the two guide rollers, and then flip the
machine back into the proper position.
Pull Air Dam Onto Insert Fastening
Deflector Roller Screw
Align Air Dam with
Guide Wheels
36 888-785-4485
37. Resources:
How To
Clean a Nozzle
It is important to clean the BITUMAT B2 nozzle after every
use to avoid bitumen buildup that restricts airflow. Buildup can
cause the machine to overheat, damaging the heating element.
To clean the nozzle, use a stainless steel or brass wire brush,
and in a motion away from your body scrape the excess bitumen Safety
off. Recommendations:
Make sure the nozzle is still hot while you do this because the • Hold the hot-air blowerʼs green
handle with your free hand to
bitumen will be more difficult to scrape away if it has had time to secure it in place while scraping.
cool and solidify. • Wear protective gloves and
safety glasses.
Continue until you can see that all the air holes are clear of • Make sure the blower is turned
off so that loose bitumen pieces
blockages. At least once a week, hold up the nozzle to a light
are not blown into the air.
source and check that light is showing through all air holes.
37
38
40
41
42 888-785-4485
38. Resources:
How To
Remove Fastening
Clean a Drive Roller Screw
Built-up bitumen can cause the drive roller to lay unevenly against the
material surface, leading to a poor weld. For this reason, itʼs important
to clean your drive roller after each use. To do so:
1. Unscrew the brass fastening screw and pull it away from the drive
roller. Wipe Off Bitumen
2. Pull the drive roller off the machine.
Reinstall
3. Spray silicone onto the drive roller and a clean rag. Fastening Screw
4. Wipe away the bitumen using the rag.
5. Once clean, coat the drive roller with a layer of silicone to help keep
it clean.
6. Reinstall the drive roller and secure it in place with the fastening
screw.
38
40 888-785-4485
39. Resources:
How To
Install a Lifting Device
The lifting device—equipped on all BITUMAT B2ʼs sold in the US—is attached to the
drive wheel scraper. With frequent use, there may be times where you need to take off
the device for cleaning. To do so, follow these instructions:
1. Unscrew and remove the weight and extra drive roller from the front of the machine.
2. Unscrew and remove the lifting device bracket from the side of the machine.
3. Flip the machine on its side with the hot-air blower facing up.
4. Remove the two fastening screws securing the scraper to the bottom of the machine.
Unscrew Lifting
Device Bracket
Flip Machine On Loosen Fastening
Unscrew Weight Its Side Screw
39
38
40 888-785-4485
40. Resources:
How To
To reinstall the lifting device, follow the steps on the previous page
in reverse order.
When going through the reinstallation process, keep the following
tips in mind:
• Put the BITUMAT B2 on top of a secure, flat surface, and let
the front end overhang the edge slightly. This offers greater
access to hard-to-reach areas. Insufficient Space
• As you tighten the fastening screws of the scraper, pull the
scraper toward you. If the scraper is too far back when it is
secured, it will rub against the drive roller, causing undue
stress on the motor.
NOTE: The space between the drive roller and scraper should be
the thickness of a dime.
38
40 888-785-4485
41. Resources:
Troubleshooting
Poor Weld Quality
There are a number of variables that can impact a BITUMAT B2ʼs welding performance.
Below are three things you can check while on a roof. If none of these resolve the welding
issue, contact IHSʼ authorized service center.
To resolve poor welding quality:
1. Check that the temperature, speed and air-volume settings are properly configured. If any
of these are off for the material or the environment, your seam quality will suffer.
Note: The amount of air blowing through the heating element will have an inverse affect on
heat output, limiting how hot the BITUMAT B2 can get.
2. Make sure the welding nozzle is free of melted bitumen and debris, which can restrict
airflow. If you discover any blockages, scrape them away with a stainless steel or brass
wire brush (see pg. 37 for details).
41
38
40 888-785-4485
42. Resources:
Troubleshooting
3. Make sure the machine is receiving the proper power supply (see pg. 12 for details) by
checking (in order) the power source, extension cord, and then machine power cord.
• First, check that the power source is producing enough power. Use an AC
voltage tester with prong probes, and make sure to wear insulated gloves. If the
power doesnʼt meet the machine requirements, below are some tips to resolve the
issue. (Click here for a complete blog post on the topic.)
Generator Wall Outlets
Contact your distributor •Invest in a generator to ensure you have a consistent power
or the manufacturer to source from job site to job site.
troubleshoot the issue •Purchase a buck-boost transformer, which can help to
and determine the maintain consistent power output.
appropriate fix. •Contact a certified electrician to examine the electrical system.
He or she may be able to safely boost power output.
42
38
40 888-785-4485
43. Resources:
Troubleshooting
• If the power source checks out, next test the
extension cord. Use the voltage tester to test the
cord outlet that the machine plugs into. If there is a
problem detected, youʼll need to purchase a new
cord.
• Lastly, check that the BITUMAT B2ʼs power cord
is not frayed, cut or sliced. If it is, it will need to
be replaced by an authorized Leister technician.
After youʼve ruled out all these variables, if your machine is still welding poorly youʼll need
to send it to an authorized Leister service center for support.
43
38
40 888-785-4485
45. Parts List
Visit:
IHShotair.com/B2-Parts-1 to
view the full-sized diagram
of the BITUMAT B2 with part
numbers.
See page 50 for a parts
diagram of the
standard ELECTRON hot
air blower, which is the
heat source for the
BITUMAT B2.
45 888-785-4485
46. Call for a Quote
888-785-4485
Parts List
Pos Order No. Qty Part Name Pos Order No. Qty Part Name
1 107.073 1 Undercarriage (complete) 20 125.739 1 Base weight
2 104.266 2 Rollpin spring ø 4 x 20 mm 20 100.871 2 Cheese head screw M8 x 20 mm
3 100.142 2 Thread forming fillister head screw M5 x 12 mm 20 125.793 1 Pressure roller retainer
4 100.124 2 Spring ring M5 5.35/9.2/1.2 mm 20 138.877 1 Centering nut
5 100.173 2 Torsional protection disk 24 138.136 1 Threaded rod
6 104.268 1 Internal retaining ring ø 52 mm 25 113.898 1 Hexagon nut M12/0.5d mm
7 108.115 1 Driving axle 26 138.135 1 Weight
8 106.811 1 Parallel key 6 x 6 x 22 mm 27 114.113 1 Roller chain 8 x 1/8 in. x 408 mm (39 ft. 5 in./min.)
9 107.085 1 Chain adjuster 27 110.553 1 Chain joint 8 x 3 mm
10 102.241 1 Washer M4 4.3/12/1 mm 28 106.731 2 Cheese head screw M6 x 16 mm
11 107.733 1 Spring washer M4 4.3/8/0.5 mm 29 100.951 2 Washer M6 6.4/12/1.6 mm
12 106.732 2 Cheese head screw M4 x 20 mm 30 137.918 1 Wiper
13 101.008 1 Spring ring M4 4.25/7.6/0.9 mm 31 107.714 1 Hinge (complete)
14 116.003 1 Set screw M6 x 8 mm 32 104.234 1 Hexagon set screw M4 x 10 mm
15 127.575 1 Spacer shaft 33 100.945 2 Slotted pan head screw M6 x 16 mm
16 137.895 2 Pressure roller 100 mm with shoulder 34 137.899 1 Guide shaft (complete)
16 137.896 2 Pressure roller 75 mm with shoulder 35 121.619 1 Shoulder bolt M5 x 8 mm
16 140.229 2 Pressure roller 100 mm without shoulder 36 114.500 1 Pillow block
16 140.228 2 Pressure roller 75 mm without shoulder 37 100.356 1 External retaining ring ø 14 mm
17 138.148 1 Fastening screw, brass 38 102.408 2 Countersunk screw M6 x 20 mm
18 101.113 2 Cheese head screw M6 x 20 mm 39 107.053 2 Retaining disk
19 100.299 13 Fillister head screw M4 x 10 mm 40 107.052 1 Bearing bush
46 888-785-4485
47. Call for a Quote
888-785-4485
Parts List
Pos Order No. Qty Part Name Pos Order No. Qty Part Name
41 107.092 1 Axle suspension 60 100.374 1 Locking nut M5, hexagon
42 107.953 1 Spiral pin ø 5 x 30 mm 61 126.895 1 Roller
43 137.894 1 Transportation axle 62 115.198 1 Fitted shoulder screw M6 x 8 mm, with socket head
44 100.341 2 External retaining ring ø 15 mm 63 137.696 1 Guiding bar bottom
45 107.074 1 Rocker (complete) 64 101.113 2 Cheese head screw M6 x 20 mm
46 125.621 1 Flange sleeve 65 140.933 1 Clamping lever M8 x 25 mm
47 107.069 1 Deflection roller (complete) 66 100.424 1 Cheese head screw M5 x 16 mm
48 107.042 1 Collar screw 67 126.597 1 Cable fixation clip Ø 12.5 mm
49 104.224 1 Round belt 68 130.275 1 Snap hook
50 140.125 1 Electron BITUMAT B2 69 137.843 1 Guiding bar upper part (complete)
51 100.909 1 Retaining ring 120 x 8 mm 70 138.817 1 Hand brush, stainless
52 100.442 4 Cheese head screw M4 x 16 mm 71 100.977 1 Set screw M6 x 12 mm
53 102.047 1 Gasket ø 60/83 x 2 mm 72 108.221 1 Pressure spring ø 1.25 x ø 6.3 x 25 mm
54 126.239 1 Grounding ring 140.489 1 Carrier box BITUMAT B2, 750 x 555 x 450 mm, green
55 126.386 1 Heating element type 38C2, 230V / 6500W 200 108.120 2 Pinch roller
55 126.594 1 Heating element type 38C2, 400V / 6500W 201 107.071 2 Pinch roll (complete)
56 102.046 1 Mica tube ø 56.5 x 155 mm 202 107.093 2 Rubber ring ø 74/92 x 40 mm
57 138.047 1 BITUMAT B2 Nozzle 100 mm 300 138.328 1 Guide roller (complete)
57 138.048 1 BITUMAT B2 Nozzle 75 mm 301 104.263 1 Springy thrust piece M8 x 16 mm
58 103.361 1 External retaining ring ø 8 mm 302 100.299 2 Fillister head screw M4 x 10 mm
59 138.152 1 Air scoop 100 mm (complete) 303 140.219 1 Mounting plate guide roller
59 138.150 1 Air scoop 75 mm (complete) 304 100.351 1 Shim ring 8/14/0.5 mm
47 888-785-4485
48. Call for a Quote
888-785-4485
Parts List
Pos Order No. Qty Part Name Pos Order No. Qty Part Name
305 126.945 1 Rocker (complete) 508 104.262 2 Circlip for shaft ø 8 mm
306 107.730 1 Hexagon nut M10/0.8d 600 125.985 1 Drive unit 39 ft. 5 in./min.
307 107.079 1 Axle 601 101.060 1 External retaining ring ø 12 mm
308 107.703 1 Guide roller (complete) 602 127.419 1 Chain wheel 39 ft. 5 in./min. 11 mm wide
309 100.976 1 Hexalobular socket pan head screw M5 x 12 mm 603 135.440 1 Planetary gear set (complete), 195:1
310 103.519 1 Cheese head screw M8 x 30 mm 604 107.061 1 Gear support
311 124.298 1 Countersunk screw M4 x 10 mm 605 114.109 1 Motor support 39 ft. 5 in./min.
400 115.427 1 Tool holder (complete) 606 100.142 4 Thread forming fillister head screw M5 x 12 mm
401 100.906 1 Tool holder 607 114.112 1 Toothed belt 5/16 in., 39 ft. 5 in./min.
402 115.426 2 Flange sleeve ø 20/28/35 x 20 mm 608 100.429 2 Carbon brush 5 x 6 x 14 mm with lead (230/200V)
403 100.362 1 Rollpin spring ø 3 x 20 mm 609 128.907 1 Motor DCS 52/33, 230V, 12 m
404 100.361 1 Pressure spring 610 112.503 1 Cheese head screw M4 x 40 mm
405 100.359 1 Trigger 611 103.782 2 Cheese head screw M4 x 60 mm
406 100.360 1 Lock pin 612 126.017 1 Temperature resistant wire AWG20 x 145 mm
500 140.232 2 Holding-down roller (complete) 613 126.018 1 Temperature resistant wire AWG20 x 180mm
501 100.299 2 Fillister head screw M4 x 10 mm 700 141.671 1 Lift up device for BITUMAT B2
502 138.468 2 Safety cover (complete) 700 140.476 1 Lift up device for BITUMAT B2 (complete)
503 107.056 2 U-profile 701 141.465 1 Lift up device holder
504 107.077 2 Holding-down roller 702 141.463 1 Lift up device wiper
505 104.267 2 Rollpin spring ø 8 x 20 mm 703 100.299 2 Fillister head screw M4 x 10 mm
506 127.778 2 Compressing spring 704 101.008 2 Spring ring M4 4.25/7.6/0.9 mm
507 107.055 2 Guide pillar 705 141.470 1 Lift up device lever
48 888-785-4485
49. Call for a Quote
888-785-4485
Parts List
Pos Order No. Qty Part Name
706 101.060 1 External retaining ring ø 12 mm
707 101.154 2 External retaining ring ø 10 mm
708 114.316 2 Washer M10 10.5/20/2 mm
709 141.438 1 Lift up device role
710 128.743 1 Handle
711 141.485 1 Stop angle (complete)
49 888-785-4485
50. Parts List
Standard on each
BITUMAT B2 is an
ELECTRON hot air
blower—the machineʼs
main heat source.
Visit:
IHShotair.com/B2-Parts-2
to see a full-sized parts
diagram of the
ELECTRON.
50 888-785-4485
51. Call for a Quote
888-785-4485
Parts List
Pos Order No. Qty Part Name Pos Order No. Qty Part Name
301 100.299 6 Fillister head screw M4 x 10 mm 323 125.458 1 Mounting ring for nozzle
302 100.032 1 Company label 75 x 22 mm 324 100.528 1 Warning label "Hot surface"
303 140.134 1 ELECTRON enclosure 325 127.548 1 Temperature resistant wire 1.5 mm2 x 1100 mm, yellow
304 101.237 1 O-ring ø 75.92 x ø 1.78 mm 326 126.383 1 Temperature resistant wire 1.5 mm2 X 1100 mm, white
305 101.252 1 Rubber ring without cams 327 126.382 1 Temperature resistant wire 1.5 mm2 x 1100 mm, black
306 140.126 1 Fixing clip 328 115.831 2 Temperature resistant wire AWG20 x 1 m, white
307 113.578 1 Hexagon counternut M16 x 1.5 mm 329 126.384 1 Temperature resistant wire AWG20 x 1100 mm. red
308 113.577 1 Cable screw fitting M16 x 1.5, NW 12, straight, black 330 126.385 1 Temperature resistant wire AWG20 x 1100 mm, blue
309 107.753 1 Cable sleeve NW 12, black, 450 mm 331 117.823 2 Silicon tube ø 8 x 0.5 x 100 mm
310 100.186 2 Thread forming fillister head screw M4 x 8 mm 332 100.151 1 Cord fastener 85 x 22 mm
311 113.712 1 Motor 54/25 KS, 230V 333 107.687 4 End sleeve, 0.5 mm2, white
312 113.720 2 Brushholder for KL/KS-Motor 334 110.808 2 End sleeve, 1.5 mm2, red
313 114.785 2 Carbon brush 5 x 6 x 16 mm for KL/KS-Motor (230/200V) 335 107.686 1 End sleeve, 2.5 mm2, blue
314 101.251 1 Steel hub 336 127.455 1 Threaded hose coupling, angled, M20 x 1.5 mm
315 104.064 1 Turbine housing lower part (complete) 337 113.569 1 Hexagon counternut M20 x 1.5 mm
316 100.284 3 Thread forming fillister head countersunk screw M4 x 14 mm 338 102.215 1 Electronic circuit board DS 85, 240/230/200V
317 107.591 1 Turbine 339 102.233 1 Potentiometer 100 kOhm
318 107.762 1 Distributor (complete) 340 100.450 1 Potentiometer knob black
319 107.592 1 Turbine 341 140.178 1 Insulating paper
320 100.287 1 Hexagon nut M5/0.5d mm 342 140.275 1 Adhesive company label
321 126.258 1 Turbine housing upper part 3 sockets, photo IC 343 107.175 4 Shrink sleeve 1/8 in. x 14 mm, black
322 101.269 4 Fillister head countersunk screw M3.5 x 8 mm 344 125.757 1 Photo IC
51 888-785-4485
53. Call for a Quote
888-785-4485
Accessories
Each of the following BITUMAT B2 accessories can be purchased separately.
(All items featured below are included with the purchase of a BITUMAT B2, except for the pressure roller.)
Bitumen-Nozzle Wooden Storage Case Heating Element Drive Roller
Order No: 138.048—75 mm Robust case 28.35 x 18.5 x 230V; 6700W Order No: 137.895—80 mm
Order No: 138.047—100 mm 17.7 inches Order No: 126.386 Order No: 137.896—100 mm
Order No: 140.489
Lifting Device Stainless Steel Wire Brush Pressure Roller (not included)
Order No: 140.476—75 mm Order No: 138.817 One-arm, silicon pressure roller
with ball bearings
Order No: 140.160—40 mm
53 888-785-4485
55. Call for a Quote
888-785-4485
Related Products
Leister offers a variety of other welding machines designed for specific roofing
applications. To learn more about any of the following products, please contact IHS at
888-785-4485 or info@ihshotair.com.
The Leister VARIMAT V2 offers the fastest welding speeds of
polymer roofing membranes on the market—up to 39 feet per
minute—and its slim design allows for welding in gaps as
narrow as 4.33 inches. While designed for flat commercial and
industrial roofs, the VARIMAT V2ʼs motor is strong enough to
weld at inclines up to 30 degrees.
The UNIROOF E is a compact roofing membrane welder for PVC,
TPO, ECB, EPDM and CSPE. Its small design makes it ideal for
edge work and hard-to-reach areas.
55 888-785-4485
56. Call for a Quote
888-785-4485
Related
Products
The TRIAC DRIVE is a semi-automatic welding machine designed for
use in conjunction with the TRIAC S or TRIAC PID hot-air hand tools.
It can produce high-quality welding on thermoplastics, and is ideal for
use on high-pitched roofs, parapet walls, vertical walls and special
flashing details.
Contact IHS to learn more about any of these Leister
products—888-785-4485 or info@ihshotair.com.
56 888-785-4485
58. World-Class Leister Authorized
Service & Support
IHS is an authorized master distributor and certified Leister
service and repair center. We offer a state-of-the-art facility Service Center
and the experienced technicians needed to quickly 888-785-4485
troubleshoot, diagnose and repair your Leister equipment to info@ihshotair.com
like-new condition. www.IHShotair.com
As part of our world-class service, we offer:
• Live Video Chat—Connect with us from the job site. We can set up live video chats
with you and your tools and remotely see what you see, quickly troubleshoot issues,
and then recommend quick fixes or next steps.
• Arranged Pick Up and Delivery—IHS will arrange for your BITUMAT B2 to be picked
up and dropped off after it has been serviced, saving you money in costly shipping
fees.
58 888-785-4485
59. World-Class Leister
Service & Support
• Expertise—Certified technicians employed full time for immediate troubleshooting
support.
• Equipment—State-of-the-art instrumentation and tools to run diagnostic tests, make
repairs and recalibrate settings.
• Preventative Maintenance—With each repair, we also perform any necessary
preventative maintenance to prolong the life of your tool and help avoid future
breakdowns.
• Inventory—We stock of tools and parts onsite to streamline order shipment and repairs.
• Rentals—Rent a replacement tool while IHS repairs your broken one and avoid costly
downtime.
If you have questions about your BITUMAT B2, or are in need of
service and support, please contact us.
59 888-785-4485
60. Warnings and Cautions
WARNINGS CAUTIONS
• Rated voltage stated on the device must correspond
• It is dangerous to open the BITUMAT B2 casing while
to the power voltage—N 61000-3-11; Zmax = 0.105 Ω
the machine is plugged in because electrified
+ j 0.066 Ω. If necessary, consult an electrician.
components and connections are exposed. Unplug the
machine before opening it. • In case of a power failure, unplug the machine and set
the main power switch to 0.
• Incorrect use of the hot-air welder can cause a fire, and
is an explosion hazard around combustable materials • For personal protection, we strongly recommend the
BITUMAT B2 be connected to an RCCB (Residual
and gasses.
Current Circuit Breaker) before operation.
• Do not touch a hot welding nozzle, as they can cause
burns. Allow it to cool first. • The tool must be operated under supervision. Hot air
can ignite flammable material that is not in view.
• Do not point the hot airflow in the direction of people or
animals. • The machine should only be used by qualified
specialists or under their supervision. Children are not
• Connect the tool to a power source with a grounding
authorized to use this device.
conductor. Any faults of the grounded conductor inside
or outside the tools are dangerous. • Protect the device from exposure to damp or wet
areas.
• Only use extension cords that are grounded.
• When lifting the BITUMAT B2 by hand, use the
carrying handle and top of the guide bar.
60 888-785-4485
61. About IHS
Industrial Heat Sources (IHS) is one of four certified U.S.
master distributors of Leister roofing products, meaning
you can trust us to deliver quality, direct-the-from-
manufacturer hot-air equipment at the best possible
prices.
We work with customers across a variety of industries,
including: roofing, process heat, industrial
fabrics, flooring, civil engineering and plastic fabrication.
In addition, we offer unmatched service and support at
our state-of-the-art facility, as well as through our service
center network across the Midwest and Northeast
regions, giving you quick access to trained Leister
technicians.
61 888-785-4485
62. Connect with Us
For more resources on the BITUMAT B2 and other Leister tools, and tips for roofing and
industrial-heat applications, visit our blog at IHShotair.com/hot-air-tools-blog, or connect
with us on:
@IHShotair
YouTube.com/user/IHShotair
Facebook.com/IHShotair
62 888-785-4485
63. Disclaimer
Information is intended as a guide only and should be used by individuals familiar with the
Leister BITUMAT B2ʼs features, functionality and parts. IHS is not responsible for injury or
equipment damage that may result from operator negligence.
Prior to setting up, operating or performing maintenance on your Leister BITUMAT B2, be
sure to read through all safety warnings and cautions contained within the product
operating manual. If you have any questions, need assistance or would like a product
demo, contact the IHS service center at 888-785-4485.
63 888-785-4485