Deflagration Flame Arresters are fire safety devices used to protect stored or process media from deflagrations. A deflagration flame arrester can be used on the top of a tank in certain conditions, as an in-line safety device where combustible gases are transported through low pressure pipe lines.
The Williams & Davis Series 2000D is a classic 2-pass, dry-back horizontal firetube boiler that offers high efficiency, flexibility, reliability, safety and ease of operation. The Dryback design provides full access to boiler tubes, tube sheet, and furnace for ease of maintenance and includes single rear tube sheet construction, which reduces tube sheet stresses. Series 2000D provides high flue gas velocities and low stack temperatures to maximize its performance. All units are factory fire tested and shipped as an integrated package, ready for quick connection to utilities.
Groth Corporation's Pressure/Vacuum Relief Valves, Pressure Relief Valves, Vacuum Relief Valves, Pilot Operated Valves, Flame and Detonation Arresters, Emergency Relief Valves, Waste Gas Burners, Pressure Regulators and more have been protecting refineries, chemical processing plants and facilities with atmospheric, fixed-roof storage tanks for more than 50 years.
Flame control products for industrial fluid operationsCTi Controltech
Groth Corporation's Pressure/Vacuum Relief Valves, Pressure Relief Valves, Vacuum Relief Valves, Pilot Operated Valves, Flame and Detonation Arresters, Emergency Relief Valves, Waste Gas Burners, Pressure Regulators and more have been protecting refineries, chemical processing plants and facilities with atmospheric, fixed-roof storage tanks for more than 50 years.
Tuning forks, with their stable resonant frequency, have been applied in numerous ways throughout many years. A modern application in industrial process control is the vibrating tuning fork level switch.The Jerguson Series 200 is a single point level switch which may be installed in any position in a pipe or vessel to detect the presence of a liquid.
The Series 200 employs a tuning fork style probe which vibrates at its natural frequency when in air. A piezoelectric crystal-system
is used to create a 1100 Hz vibration in the tuning fork. As the
tuning fork is covered by a liquid or slurry, a corresponding
shift occurs in the vibrating frequency of the tuning fork. This
shift is being monitored continuously and once a present threshold is exceeded, the output changes status.
Deflagration Flame Arresters are fire safety devices used to protect stored or process media from deflagrations. A deflagration flame arrester can be used on the top of a tank in certain conditions, as an in-line safety device where combustible gases are transported through low pressure pipe lines.
The Williams & Davis Series 2000D is a classic 2-pass, dry-back horizontal firetube boiler that offers high efficiency, flexibility, reliability, safety and ease of operation. The Dryback design provides full access to boiler tubes, tube sheet, and furnace for ease of maintenance and includes single rear tube sheet construction, which reduces tube sheet stresses. Series 2000D provides high flue gas velocities and low stack temperatures to maximize its performance. All units are factory fire tested and shipped as an integrated package, ready for quick connection to utilities.
Groth Corporation's Pressure/Vacuum Relief Valves, Pressure Relief Valves, Vacuum Relief Valves, Pilot Operated Valves, Flame and Detonation Arresters, Emergency Relief Valves, Waste Gas Burners, Pressure Regulators and more have been protecting refineries, chemical processing plants and facilities with atmospheric, fixed-roof storage tanks for more than 50 years.
Flame control products for industrial fluid operationsCTi Controltech
Groth Corporation's Pressure/Vacuum Relief Valves, Pressure Relief Valves, Vacuum Relief Valves, Pilot Operated Valves, Flame and Detonation Arresters, Emergency Relief Valves, Waste Gas Burners, Pressure Regulators and more have been protecting refineries, chemical processing plants and facilities with atmospheric, fixed-roof storage tanks for more than 50 years.
Tuning forks, with their stable resonant frequency, have been applied in numerous ways throughout many years. A modern application in industrial process control is the vibrating tuning fork level switch.The Jerguson Series 200 is a single point level switch which may be installed in any position in a pipe or vessel to detect the presence of a liquid.
The Series 200 employs a tuning fork style probe which vibrates at its natural frequency when in air. A piezoelectric crystal-system
is used to create a 1100 Hz vibration in the tuning fork. As the
tuning fork is covered by a liquid or slurry, a corresponding
shift occurs in the vibrating frequency of the tuning fork. This
shift is being monitored continuously and once a present threshold is exceeded, the output changes status.
Atomac valves provide bubble-tight shutoff, low maintenance, no-leak stem seals and the safety assurance of a blowout-proof stem assembly. LIned ball valves deliver high levels of corrosion resistance.
Rupture Disc Products For Industrial Process SafetyCTi Controltech
Built on years of research and development, the HPX® and SANITRX HPX® Rupture Discs (bursting discs) are high precision pressure relieving devices that protect personnel, equipment and the environment. The versatility of the HPX® product family offers pressure protection for a wide range of applications in many processing industries, including: chemical, oil and gas, food, beverage, pharmaceutical, biotech, pulp and paper, power and more.
From its beginnings in 1966, Kammer valves have been engineered and manufactured for specific answers to tough applications. Although, more than half of all Kammer valves are custom designed, custom applications often do not require additional time or cost due to the versatility and interchangeability of the Kammer design.
Specifically Designed for any industry that must obtain pressure or level transmitter readings on tanks and vessels. Valves are designed to ASME B16.34 and feature minimal dead space, preventing build-up. Purge ports and optional milled flats enable Clean In Place and drainage without process interruption.
Bolt pattern accommodates standard industry ANSI 150# flanged connections and retrofits to knife gate patterns. Hardware configuration allows separate bolting of valve to tank and transmitter to valve as an additional safety measure for hazardous media.
Kammer valves are designed to handle a wide range of service conditions: pressures from vacuum to 4000 bar and temperatures from minus 269 degrees C to plus 400 degrees C. Body materials include all common stainless steels, in addition to plastics and exotic alloys.
Strainers arrest pipeline debris such as scale, rust, jointing compound and weld metal in pipelines, protecting equipment and processes. This tutorial considers the range of strainer and filter types in use and how to size and select them for different applications.
Cash Valve provides highly engineered pressure regulating and back pressure valves along with cost effective custom packages for OEM engineered applications for industrial and commercial customers who require mechanical control of pressure.
Cash Valve provides product from cryogenic through high temperature for Steam, Air, Gas, and Liquid applications meeting tight shut-off and extended service life. Cash Valve provides code certifications that meet various global standards such as PED, TPED, and Chinese as well as non-code requirements.
Flowserve, under their Valtek brand, developed a control valve that combines a number of useful design features. The MaxFlo 4 is an eccentric rotary plug valve intended for fluid control operations. The valve has some attractive design features.
Combining Rupture Discs and Safety Relief ValvesCTi Controltech
Isolating a relief or safety valve from the process media through the installation of a rupture disc upstream of the valve inlet will eliminate exposure of the costly valve to effects of the media.
Measuring level of liquid in a tank or vessel can be accomplished in a number of ways, all of which require some arrangement of instrumentation to either infer the liquid level from the measurement of a related physical property, or directly deliver the liquid level visually using a scaled gauge arrangement. One indirect method of level measurement is the bubbler method, so named because it employs a purging gas that continually vents from the bottom of a tube extending into a tank of liquid. Through a simple apparatus, the level of a liquid can be inferred by the amount a back pressure exerted upon the gas flowing through the tube.
These instruments are what will be required to build a level measurement apparatus that uses the bubbler method.
The ISV product line includes valve sizes ranging form 1/4" to 56" in pressure classes through 2500 and up to 10,000 psig working pressures with a large selection of body materials and trims.
Pipeline, Oil & Gas Service Ball Valves
API 6D and API 608, API 607 Firesafe with NACE compliance
2 & 3 piece trunion mounted ball valves
2 & 3 piece floating ball valves
Industrial Floating Ball Valves
API 608 / ASME B16.34, API 607 Firesafe with NACE compliance
2 & 3 piece flanged, SW, BW and NPT
Uni-body NPT
2 & 3 piece NPT industrial valves
Historically electric actuators had never been deemed 'capable' in industrial applications. Not capable as they could not take the ambient temperatures of those application environments, they did not have the speed, they were not 'robust', they did not have the Fail-Safe capability, or if they did have all these attributes the cost was prohibitive. The ILEA series of industrial linear electric actuators overcomes previous weaknesses in electric valve actuators.
Typical Soft Technologies is one of the leading Software Company located in Chennai that offers best Quality projects and training to all customers.
We also deliver all the finest Projects at many Students, Companies. Our Computer Courses Provides best future for the Students. If you want any of our projects & Courses, then contact us.
dmin@typical.in
044-43555140, 093443 99926.
Atomac valves provide bubble-tight shutoff, low maintenance, no-leak stem seals and the safety assurance of a blowout-proof stem assembly. LIned ball valves deliver high levels of corrosion resistance.
Rupture Disc Products For Industrial Process SafetyCTi Controltech
Built on years of research and development, the HPX® and SANITRX HPX® Rupture Discs (bursting discs) are high precision pressure relieving devices that protect personnel, equipment and the environment. The versatility of the HPX® product family offers pressure protection for a wide range of applications in many processing industries, including: chemical, oil and gas, food, beverage, pharmaceutical, biotech, pulp and paper, power and more.
From its beginnings in 1966, Kammer valves have been engineered and manufactured for specific answers to tough applications. Although, more than half of all Kammer valves are custom designed, custom applications often do not require additional time or cost due to the versatility and interchangeability of the Kammer design.
Specifically Designed for any industry that must obtain pressure or level transmitter readings on tanks and vessels. Valves are designed to ASME B16.34 and feature minimal dead space, preventing build-up. Purge ports and optional milled flats enable Clean In Place and drainage without process interruption.
Bolt pattern accommodates standard industry ANSI 150# flanged connections and retrofits to knife gate patterns. Hardware configuration allows separate bolting of valve to tank and transmitter to valve as an additional safety measure for hazardous media.
Kammer valves are designed to handle a wide range of service conditions: pressures from vacuum to 4000 bar and temperatures from minus 269 degrees C to plus 400 degrees C. Body materials include all common stainless steels, in addition to plastics and exotic alloys.
Strainers arrest pipeline debris such as scale, rust, jointing compound and weld metal in pipelines, protecting equipment and processes. This tutorial considers the range of strainer and filter types in use and how to size and select them for different applications.
Cash Valve provides highly engineered pressure regulating and back pressure valves along with cost effective custom packages for OEM engineered applications for industrial and commercial customers who require mechanical control of pressure.
Cash Valve provides product from cryogenic through high temperature for Steam, Air, Gas, and Liquid applications meeting tight shut-off and extended service life. Cash Valve provides code certifications that meet various global standards such as PED, TPED, and Chinese as well as non-code requirements.
Flowserve, under their Valtek brand, developed a control valve that combines a number of useful design features. The MaxFlo 4 is an eccentric rotary plug valve intended for fluid control operations. The valve has some attractive design features.
Combining Rupture Discs and Safety Relief ValvesCTi Controltech
Isolating a relief or safety valve from the process media through the installation of a rupture disc upstream of the valve inlet will eliminate exposure of the costly valve to effects of the media.
Measuring level of liquid in a tank or vessel can be accomplished in a number of ways, all of which require some arrangement of instrumentation to either infer the liquid level from the measurement of a related physical property, or directly deliver the liquid level visually using a scaled gauge arrangement. One indirect method of level measurement is the bubbler method, so named because it employs a purging gas that continually vents from the bottom of a tube extending into a tank of liquid. Through a simple apparatus, the level of a liquid can be inferred by the amount a back pressure exerted upon the gas flowing through the tube.
These instruments are what will be required to build a level measurement apparatus that uses the bubbler method.
The ISV product line includes valve sizes ranging form 1/4" to 56" in pressure classes through 2500 and up to 10,000 psig working pressures with a large selection of body materials and trims.
Pipeline, Oil & Gas Service Ball Valves
API 6D and API 608, API 607 Firesafe with NACE compliance
2 & 3 piece trunion mounted ball valves
2 & 3 piece floating ball valves
Industrial Floating Ball Valves
API 608 / ASME B16.34, API 607 Firesafe with NACE compliance
2 & 3 piece flanged, SW, BW and NPT
Uni-body NPT
2 & 3 piece NPT industrial valves
Historically electric actuators had never been deemed 'capable' in industrial applications. Not capable as they could not take the ambient temperatures of those application environments, they did not have the speed, they were not 'robust', they did not have the Fail-Safe capability, or if they did have all these attributes the cost was prohibitive. The ILEA series of industrial linear electric actuators overcomes previous weaknesses in electric valve actuators.
Typical Soft Technologies is one of the leading Software Company located in Chennai that offers best Quality projects and training to all customers.
We also deliver all the finest Projects at many Students, Companies. Our Computer Courses Provides best future for the Students. If you want any of our projects & Courses, then contact us.
dmin@typical.in
044-43555140, 093443 99926.
Verbetertrajecten dienstverlening in Apeldoorn (piet stoop)KING
Presentatie gehouden tijdens de inleiding van de praktijkmiddag dienstverlening van KING in Apeldoorn in februari 2014. Door Apeldoorn – Piet Stoop. Om dienstverlening te verbeteren werken gemeenten vaak aan verschillende facetten in de dienstverlening. Zo combineert de gemeente Apeldoorn bijvoorbeeld gesprekstechnieken voor een warm contactmoment met procesoptimalisatie.
Field-portable, light-duty, industrial,
single-chamber blast machines rated
at 125 psi working pressure. Model 1028,
holds 1/2 cubic foot of media (50 lbs
expendable, mineral abrasive). This unit
is equipped with MSV abrasive metering
valve.
Parker Balston is a division of Parker Hannifin, world’s leading diversified manufacturer of motion and control technologies and systems. Balston manufacturers industrial filters and filtration technology, replacement filter elements, compressed air dryers, nitrogen generators, and compressed air microbial detection.
WOM Cementing and Circulating hose loops utilize the combination of WOM’s swivel joint flexibility and hose design for easy connection and storage for transportation.
Integral Connections, Integral Connections Oilfield Equipment - WOM Groupwomgroup
WOM Group provides Well Service Solutions including integral connections. All Integral Connections are subjected to controlled heat-treat processes to help integrity.
The Variable Area flowmeter is an instrument for metering the flowrate of liquids and gases in a pipeline. It includes a vertically oriented conical tube, whose diameter is larg- er at the top than at the bottom, through which the fluid flows upward and in which a vertically moving float is positioned.
A Control Valve is the most commonly used
final control element used to regulate fluid flow in
a process. In a process, normally it is the only
controllable element residing in the loop.
Ø This is a device used to modulate flow of
process fluid in pipe lines by creating a variable
area in the flow path.
Ø The flow path is varied with respect to the
control signal received from the controller
towards the required flow modulation.
development of main headings and gate roads with the use of road heading and bolter miners has paramount importance for effective production from a Longwall mine
Monitrol is a turn-key fluid control system including a globe style control valve, a variety of built in sensors for Flow, Pressure and Temperature, a High Precision Electric Actuator, along with controller and an easy to use Touch Screen interface. Monitrol can manage up to three variables (sensors), simultaneously with its control logic. Flexibility allows the control logic in Monitrol to be bypassed if that is desired. A Building Management System can still maintain all control and just make use of the sensor information if that is desired. A full range of I/O signals, feedback and modbus TCP communications are standard.
Integrated control valve, sensors, actuator, and controller
6 cu-ft-contractor
1. Description 6 Cu Ft
Field portable, high-production, single
chamber blast machine, rated at 150 psi,
(for one operator). Holds 6 cubic feet of
Contractor
blast media. Equipped with Millennium
pneumatic remote controls and Quantum
Blast Machine
manual metering valve.
T ECHNICAL D ATA S HEET
Stock No. 21610
Note: For safe, efficient blasting, read
and follow the owner's manual and seek
training for everyone who will use this
equipment.
Purpose
High-performance blast cleaning
system removes corrosion, mill scale, and
coatings from most surfaces. Produces a
uniform surface texture, and creates a
surface profile to increase bonding for
coatings. See related literature for
additional applications. Machine holds 6
cubic feet of abrasive for up to 30
minutes of continuous blasting at 100 psi
with standard No. 6 nozzle (3/8-inch
orifice).
Requirements for Operation
• Clean, dry, compressed air of
sufficient volume to maintain desired
pressure at the nozzle. See Air
Consumption Chart in Blast Off 2
booklet.
• Maximum working pressure 150 psi
• Minimum pressure 30 psi needed to
operate OSHA-required remote control
valves
• NIOSH-approved supplied-air
respirator
• Grade D breathing-air supply as
defined by the Compressed Gas Advantages • Central hookup point for blast hose and
Association Commodity Specification: remote controls
• Rated for 150-psi maximum working
G-7.1 (www.cganet.com) • Weather-resistant storage area holds
pressure
• Abrasive blast media - consult abrasive manuals, paperwork and small parts
• 11/2-inch Millennium valve provides
supplier for appropriate media for your
application
unrestricted air flow Approvals and Certifications
• Quantum metering valve maintains Blast machine pressure vessel built to
smooth, consistent flow, adjustment American Society of Mechanical
Description of Operation knob allows precise control of Engineers (ASME) code for 150-psi
media flow working pressure. Vessel is hydro-
The operator controls blasting from a
• 11/4-inch piping allows up to 50 statically tested and National Board
remote control handle at the nozzle.
percent increase in air flow, when certified.
Pressing the handle starts blasting,
compared to standard 1-inch piping
releasing it stops blasting. The blast Remote control system complies with
• 29-inch width fits through standard
machine contains abrasive and meters it OSHA regulation 1910.244 (b).
doorways
into the compressed air stream.
• Four-wheel integral cart for ease of
moving
• Robust handles act as skid for loading
machine into pickup or trailer and
protect valves and piping from damage
