2. Machine Description (Information)
TSDP
General Description
Information:-
• is used to obtain information that is captured by the system. The
following information can be obtained:-
• Event Log - series if events taken place in the machine during
auto run including machine warnings and errors, in
chronological order.
• MIS Display - information about the product that is being
processed in the machine and measurements of machine
performance.
• Temperature - real time temperature reading as measured by
the thermocouples in the Turn Table and Mould Chase for
example.
• State Chart - real time state (active/inactive) of each module
and their sub modules.
2
Carsem Confidential A member of the Hong Leong Group
3. Machine Description (Information)
TSDP
General Description (cont.)
• Debug Log - time-based log of hardware changes,
commands/event executing and completed to facilitate the
debugging. The log is password protected and accessed only
by ASM service personnel.
• MIS Display - real time input-output (IO) state from the sensor
and solenoid IO port.
• About - information about the system software version number,
year of issue and the machine configuration.
3
Carsem Confidential A member of the Hong Leong Group
4. Machine Description (Information)
TSDP
Information (Event Log)
The Event Log
page appears
when
is pressed.
4
Carsem Confidential A member of the Hong Leong Group
5. Machine Description (Information)
TSDP
Information (Event Log) (cont.)
Saves the displayed
Event Log page as an image file (GIF,
BIP or JPEG) into a storage media (e.g.
diskette).
Erases the entire
Event Log data. This command is
password protected.
Key in password
when this virtual
keyboard appears
on screen
Displays the top ten Configure your top
ten events here
events in descending order. You can
also configure the top ten events of
your choice here.
5
Carsem Confidential A member of the Hong Leong Group
6. Machine Description (Diagnostics)
TSDP
Information (Event Log) (cont.)
Prints the Event Log to a
printer (note: a printer must first be
connected).
Saves the entire Event Log in
selected filter option into a storage
media.
Saves the Top Ten Event Log
in selected filter option into a storage
media.
Captures events according to
the date and level selected.
Displays the events in Pareto
Chart form.
6
Carsem Confidential A member of the Hong Leong Group
7. Machine Description (Information)
TSDP
Information (Event Log) (cont.)
Event identification Date, time and Event classification Event level (e.g.
number given for location of the (e.g. Operation, Warning, Minor
each captured described event Event, Warning, Warning, Major
event. occurrence as well Error). Warning, Fatal
as its code. Warning).
7
Carsem Confidential A member of the Hong Leong Group
8. Machine Description (Information)
TSDP
Information (Event Log) (cont.)
Scroll up one
page.
Scroll up one
event.
Scroll down one
event.
Scroll up one
page.
8
Carsem Confidential A member of the Hong Leong Group
9. Machine Description (Information)
TSDP
Information (MIS Display)
The MIS Display
information is in
minutes. The
machine
performance
measurement may
differ from our
method of
measurement. For
example, the MTBF
measurement here
is based on
machine errors that
are not resolved
within 6 minutes.
Our measurement
is machine
breakdown that
requires assistance
by technicians.
9
Carsem Confidential A member of the Hong Leong Group
10. Machine Description (Information)
TSDP
Information (MIS Display) (cont.)
Product currently
processed by the
machine
Start time and date
when measurements
are taken
Number of machine
errors assisted within
6 minutes
Number of machine
errors assisted
beyond 6 minutes
Total time available
after the last reset
Total time machine is
in auto run mode
Mean Time Between
Assists
= Total Productive
Time / Assists
Mean Time Between
Failures
= Total Productive
Time / Failures 10
Carsem Confidential A member of the Hong Leong Group
11. Machine Description (Information)
TSDP
Information (MIS Display) (cont.)
Total time of all
productive time, non-
productive time, dry
cycle runs, melamine
cleaning and idle time
Total time of all error
stoppages and all
machine stoppages
Number of operation
cycles within Total
Productive Time
Number of units per
lead frame x number
of lead frames per
shot x Total Product
Cycles
Total Units Output /
Total Productive Time
Total Productive Time
/ Total Equipment
Time
Resets to start
with a new
time and date 11
Carsem Confidential A member of the Hong Leong Group
12. Machine Description (Information)
TSDP
Information (Temperature)
The temperature is feedbacked by the temperature controller to the PC and displayed on the
monitor. The frequency of the feedback is programmed by ASM, so there will be a time lag
between the temperature that is is detected by the thermocouple and that is displayed on the
screen. All modules and sub-modules like the Turn Table and Mould Chases that use heating
elements with their temperatures monitored by the system will have their temperatures
displayed here.
12
Carsem Confidential A member of the Hong Leong Group
13. Machine Description (Information)
TSDP
Information (IO Port State)
The IO Port State
displays all the
sensors and
solenoids input-
output ports
active/inactive
states. This is
important when we
want to find out
whether the input
devices are
working properly
when we
troubleshoot the
machine.
Green means
active while red
means inactive.
13
Carsem Confidential A member of the Hong Leong Group
14. Machine Description (Information)
TSDP
Information (About)
The information in About allows the user to find out whether the system is using the latest
software version. ASM provides software upgrade from time to time (when they have made
some improvements in the system or the software). It is also accessed to find out the
machine configuration of the system like whether it is using magazines for input and output,
whether vision systems are used and at which location, the number of presses in the system,
etc.
14
Carsem Confidential A member of the Hong Leong Group
