service repair manual

1. 2008 SUSPENSION
Front Suspension - Equinox & Torrent
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
REPAIR INSTRUCTIONS
STABILIZER SHAFT REPLACEMENT
Removal Procedure
1. Position the front wheels in the straight ahead position.
2. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .
3. Remove the front tire and wheels. Refer to Tire and Wheel Removal and Installation .
Application
Specification
Metric English
Brake Hose Bracket Bolt 15 N.m 11 lb ft
Lower Ball Joint to Control Arm Bolt and Nut 68 N.m 50 lb ft
Lower Ball Joint Stud Nut 40 N.m 30 lb ft
Lower Control Arm to Frame Front Bolt and Nut 150 N.m +150° 110 lb ft +150°
Lower Control Arm to Frame Rear Bolt and Nut 70 N.m 52 lb ft
Lower Control Arm Rear Bushing Nut 150 N.m 111 lb ft
Outer Tie Rod End Nut 25 N.m + 90° rotation 18 lb ft + 90° rotation
Stabilizer Shaft Insulator Clamp Bolt 50 N.m 37 lb ft
Stabilizer Shaft to Link Nut 75 N.m 55 lb ft
Stabilizer Shaft Link to Strut Nut 85 N.m 63 lb ft
Strut Assembly Shaft Nut 70 N.m 52 lb ft
Strut Upper Mount Nut 25 N.m 18 lb ft
Strut to Steering Knuckle Bolt and Nut 185 N.m 136 lb ft
Tie Rod Retention Nut 60 N.m 44 lb ft
Wheel Bearing/Hub Mounting Bolt 130 N.m 96 lb ft
Wheel Drive Shaft Nut 205 N.m 157 lb ft
2008 Chevrolet Equinox LS
2008 SUSPENSION Front Suspension - Equinox & Torrent
2008 Chevrolet Equinox LS
2008 SUSPENSION Front Suspension - Equinox & Torrent
Microsoft
Friday, August 07, 2009 10:09:14 AM Page 1 © 2005 Mitchell Repair Information Company, LLC.
Microsoft
Friday, August 07, 2009 10:09:18 AM Page 1 © 2005 Mitchell Repair Information Company, LLC.

2. Fig. 1: View Of Stabilizer Link & Stabilizer Shaft
Courtesy of GENERAL MOTORS CORP.
4. Remove the stabilizer shaft links. Refer to Stabilizer Shaft Link Replacement.
5. Remove the steering gear assembly. Refer to Steering Gear Replacement (EPS) or Steering Gear
Replacement (HPS) .
6. Rotate the left and right steering knuckle all the way forward.
IMPORTANT: In the following service procedure, it is not necessary to completely
remove the outer tie rod end from the steering rack. Relocate the outer tie
rod end to the side and support if necessary.
2008 Chevrolet Equinox LS
2008 SUSPENSION Front Suspension - Equinox & Torrent
Microsoft
Friday, August 07, 2009 10:09:14 AM Page 2 © 2005 Mitchell Repair Information Company, LLC.

3. Fig. 2: Identifying Stabilizer Bar Clamp-To-Cradle Bolts
Courtesy of GENERAL MOTORS CORP.
7. Remove the stabilizer shaft clamp to cradle bolts.
8. Remove the stabilizer shaft clamps and bushings from the stabilizer bar.
IMPORTANT: In the following service procedure, it is NOT necessary to remove the
2008 Chevrolet Equinox LS
2008 SUSPENSION Front Suspension - Equinox & Torrent
Microsoft
Friday, August 07, 2009 10:09:14 AM Page 3 © 2005 Mitchell Repair Information Company, LLC.

4. 9. Remove the catalytic convertor from the exhaust manifold. Refer to Catalytic Converter Replacement
(LNJ) .
10. Using a jack stand, raise the front of the catalytic convertor until just touches the floor panel
11. Remove the stabilizer shaft from the vehicle through the left wheel opening.
Installation Procedure
1. Install the stabilizer shaft to the vehicle through the left wheel opening.
catalytic convertor from the vehicle. Just remove it from the exhaust
manifold.
IMPORTANT: Take care not to catch the transmission shift cable or left wheel house
plastic trim when removing the stabilizer bar.
IMPORTANT: It may be necessary to rotate the stabilizer shaft 180° while removing it
from the vehicle.
IMPORTANT: Take care not to catch the transmission shift cable or left wheel house
plastic trim when installing the stabilizer shaft.
2008 Chevrolet Equinox LS
2008 SUSPENSION Front Suspension - Equinox & Torrent
Microsoft
Friday, August 07, 2009 10:09:14 AM Page 4 © 2005 Mitchell Repair Information Company, LLC.

5. Fig. 3: Identifying Stabilizer Bar Clamp-To-Cradle Bolts
Courtesy of GENERAL MOTORS CORP.
2. Install the stabilizer shaft clamps and bushings to the stabilizer bar.
NOTE: Refer to Fastener Notice .
2008 Chevrolet Equinox LS
2008 SUSPENSION Front Suspension - Equinox & Torrent
Microsoft
Friday, August 07, 2009 10:09:14 AM Page 5 © 2005 Mitchell Repair Information Company, LLC.

6. 3. Install the stabilizer shaft clamp bolts.
Tighten: Tighten the bolts to 50 N.m (37 lb ft).
Fig. 4: View Of Stabilizer Link & Stabilizer Shaft
Courtesy of GENERAL MOTORS CORP.
4. Install the stabilizer shaft links. Refer to Stabilizer Shaft Link Replacement
5. Install the steering gear assembly. Refer to Steering Gear Replacement (EPS) or Steering Gear
Replacement (HPS) .
6. Remove the jack stand from the catalytic convertor.
2008 Chevrolet Equinox LS
2008 SUSPENSION Front Suspension - Equinox & Torrent
Microsoft
Friday, August 07, 2009 10:09:14 AM Page 6 © 2005 Mitchell Repair Information Company, LLC.

7. 7. Install the catalytic convertor to the exhaust manifold. Refer to Catalytic Converter Replacement
(LNJ) .
8. Install the front tire and wheels. Refer to Tire and Wheel Removal and Installation .
9. Lower the vehicle.
STABILIZER SHAFT LINK REPLACEMENT
Fig. 5: View Of Stabilizer Shaft Link
Courtesy of GENERAL MOTORS CORP.
Callout Component Name
Preliminary Procedures
1. Raise the vehicle. Refer to Lifting and Jacking the Vehicle .
2. Remove the front wheel and tire assembly. Refer to Tire and Wheel Removal and Installation .
2008 Chevrolet Equinox LS
2008 SUSPENSION Front Suspension - Equinox & Torrent
Microsoft
Friday, August 07, 2009 10:09:14 AM Page 7 © 2005 Mitchell Repair Information Company, LLC.

8. STABILIZER SHAFT INSULATOR REPLACEMENT
Fig. 6: View Of Stabilizer Shaft Insulator, Clamp & Bolts
Courtesy of GENERAL MOTORS CORP.
1
Stabilizer Shaft Link Ball Stud Nut (Qty: 2)
Tip: Use the proper size allen wrench to keep the stabilizer link ball stud from rotate while
removing or installing the nut.
Tighten: 65 N.m (48 lb ft).
NOTE:
Refer to Fastener Notice .
2 Stabilizer Shaft Link
Callout Component Name
Preliminary Procedures
1. Raise the vehicle. Refer to Lifting and Jacking the Vehicle .
2008 Chevrolet Equinox LS
2008 SUSPENSION Front Suspension - Equinox & Torrent
Microsoft
Friday, August 07, 2009 10:09:14 AM Page 8 © 2005 Mitchell Repair Information Company, LLC.

9. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

10. LOWER CONTROL ARM BALL JOINT REPLACEMENT
Removal Procedure
2. Remove the front wheel and tire assemblies. Refer to Tire and Wheel Removal and Installation .
1
Stabilizer Shaft Insulator Bolt (Qty: 2)
Tighten: 50 N.m (37 lb ft).
NOTE:
Refer to Fastener Notice .
2 Stabilizer Shaft Insulator Clamp (Qty: 2)
3 Stabilizer Shaft Insulator (Qty: 2)
2008 Chevrolet Equinox LS
2008 SUSPENSION Front Suspension - Equinox & Torrent
Microsoft
Friday, August 07, 2009 10:09:14 AM Page 9 © 2005 Mitchell Repair Information Company, LLC.

11. Fig. 7: Identifying Drill Bit
Courtesy of GENERAL MOTORS CORP.
1. Remove the lower control arm. Refer to Lower Control Arm Replacement.
2. Place the control arm in a vise or suitable holding device.
3. Remove the ball joint rivets using the following procedure.
1. Drill through the rivets using a 8 mm (5/16 in) drill bit.
2. Enlarge the hole using a 12 mm (31/64 in) drill bit.
3. Remove any remaining burs from the control arm.
4. Remove the ball joint from the control arm. Note the position of the ball joint for reassembly.
Installation Procedure
2008 Chevrolet Equinox LS
2008 SUSPENSION Front Suspension - Equinox & Torrent
Microsoft
Friday, August 07, 2009 10:09:14 AM Page 10 © 2005 Mitchell Repair Information Company, LLC.

12. Fig. 8: View Of Ball Joint & Control Arm
Courtesy of GENERAL MOTORS CORP.
1. Install the ball joint to the control arm as previously noted.
IMPORTANT: The control arm must be clean and free of debris.
NOTE: Refer to Fastener Notice .
IMPORTANT:  Only use hardware provided with the new ball joint.
 The bolts must be installed with the bolt head on top of the ball joint.
2008 Chevrolet Equinox LS
2008 SUSPENSION Front Suspension - Equinox & Torrent
Microsoft
Friday, August 07, 2009 10:09:14 AM Page 11 © 2005 Mitchell Repair Information Company, LLC.

13. 2. Install the ball joint to control arm bolts.
Tighten: Tighten the bolts and nuts to 68 N.m (50 lb ft).
3. Install the lower control arm. Refer to Lower Control Arm Replacement.
FRONT WHEEL BEARING AND HUB REPLACEMENT
Removal Procedure
Fig. 9: View Of Front Brake Rotor
Courtesy of GENERAL MOTORS CORP.
2008 Chevrolet Equinox LS
2008 SUSPENSION Front Suspension - Equinox & Torrent
Microsoft
Friday, August 07, 2009 10:09:14 AM Page 12 © 2005 Mitchell Repair Information Company, LLC.