RELAM LFS 12F Certification: Building Components Acceptance Report (BCAR) 1278 :This is the original RELAM LFS grade by Lamco Forest Products now called grade 12F and the engineering /design values .
Cheap Rate ➥8448380779 ▻Call Girls In Iffco Chowk Gurgaon
Certification for RELAM LFS original grade by Lamco Forest Products now called grade 12F
1. PFS Corporation
2402 Daniels Street
Madison, WI 53718 Telephone: (608) 221-3361 Fax: (608) 221-0180
BUILDING COMPONENT ACCEPTANCE REPORT NO. 1278
1. TYPE OF ACCEPTANCE
Original Date of Acceptance 6/26/02 Revision Date 9/21/06
2. IDENTIFICATION
Manufacturer LAMCO Forest Products, Inc. Telephone No. 418 679-2647
Address 760 Chemin de la Moraine, St-Félicien (Québec) Canada G8K 0A1 – Mill 628
Name of Inspection Agency PFS Corporation – 2402 Daniels Street – Madison, WI 53718
3. DOCUMENTS SUBMITTED
Calculations and/or Test Data (Date Stamped 2003/03/02 )
Barlow Engineering, PC report w/Appendix B dated 2003/05/29 Sheets 1 thru 104
(RELAM® - STRUCTURAL COMPONENTS, RELAM – LFS® (LAMINATED FLOOR SYSTEM) and
RELAM – LFS® RIMBOARD up to 14”depth)
Calculations and/or Test Data (Date Stamped 2006/08/28 )
PFS Report LC 06-221 (16” depth Rimboard only) Sheets 1 thru 3
PFS Report LC 06-222 (16” depth Rimboard only) Sheets 1 thru 2
Quality Assurance Manual (Date Stamped 2006/08/29 )
QC Manual – USA Edition Sections 1 thru 11.0
4. DESCRIPTION OF BUILDING COMPONENT
See attached design value page and two American – two Canadian PFS Certificates of Conformance
Relam® components are edge laminated and finger-jointed black spruce and jack pine up to 24 feet
length. Available in depths up to 16-in. and thickness of 1-1/4 up to 1-1/2. Made using an adhesive
(NER-165, CCMC 12905R) intended for structural use where high resistance to moisture is required in
roof, wall and floor subjected to sustained loadings such as live or snow loads.
5. APPLICABLE CODES OR STANDARDS LAMCO RELAM® and RELAM-LFS® products bearing the PFS
mark are listed by the PFS Corporation to ASTM D 5456-99a (Evaluation of Structural Composite Lumber
Products as referenced in Model Codes) for use in HUD manufactured homes, modular buildings,
and conventional site built construction. RELAM LFS® RIMBOARD has not been tested for 16” to ASTM
D 5456. Hence, no design values
6. LIMITATIONS OF ACCEPTANCE (IF ANY) Holes or notches using criteria for solid sawn lumber per
NDS or as substantiated by engineering calculations verified by a registered professional engineer
using the criteria for solid sawn lumber.
This is a Building Code Acceptance Only. For building components to be certified, an
accepted concurrent QA Program is also required.
Prepared By: Reviewed By:
Robert Gorleski
Field Service Representative
Date Signed: 9/21/06
James A. Rothman, P.E.
Sr. Vice President – Q.C.
Date Signed: 9/21/06
g:BCAR – 1278
rev. 9/21/06
2. LISTING BY BUILDING COMPONENT ACCEPTANCE REPORT (BCAR)
Manufactured building components are listed by Building Component Acceptance Report (BCAR). The
identification of fabricator, documents submitted for acceptance, description of building component,
applicable codes or standards, and limitation of acceptance are contained in the report. The report
number identified in the PFS Listing Directory is the BCAR Acceptance Number.
The presence of the PFS trademark as shown below is identification of a listed building component.
The promulgation of the BCAR is contingent upon the manufacturer entering into a contract with PFS for
follow-up quality control service and product listing. Under the Trademark License Agreement with PFS the
manufacturer of a building component submits documents to PFS for review and acceptance. Upon final
PFS acceptance, a BCAR is issued and the manufacturer is authorized to attach labels or other authorized
evidences of the PFS trademark to his building component which is found by him to be in compliance with
the PFS BCAR. Representatives of PFS perform periodic inspections and/or tests of the component at the
factory or from time to time elsewhere. Failure to comply with this Agreement may result in withdrawal of the
PFS trademark.
JAR:at
8/18/94
rev. 8/27/02 kt
3. BUILDING COMPONENT ACCEPTANCE REPORT
THICKNESS DEPTH
FLEXURAL
BENDING
STRENGTH
Fb
1
TENSION
PARALLEL
TO GRAIN
Ft
1,2
SHEAR
PARALLEL
TO GRAIN
Fv
1
COMPRESSION
PERPENDICULAR
TO GRAIN
Fc┴
1
COMPRESSION
PARALLEL
TO GRAIN
Fc//
1
21
/2 2,300
31
/2 2,150
41
/2 1,600
51
/2 1,600
61
/2 1,450
THICKNESS DEPTH
FLEXURAL
BENDING
STRENGTH
Fb
1
TENSION
PARALLEL
TO GRAIN
Ft
1,2
SHEAR
PARALLEL
TO GRAIN
Fv
1
COMPRESSION
PERPENDICULAR
TO GRAIN
Fc┴
1
COMPRESSION
PARALLEL
TO GRAIN
Fc//
1
71
/4 1,450
81
/4 1,250
91
/4 - 91
/2 1,250
101
/4 to 14 1,250
THICKNESS DEPTH
FLEXURAL
BENDING
STRENGTH
Fb
1
TENSION
PARALLEL
TO GRAIN
Ft
1,2
SHEAR
PARALLEL
TO GRAIN
Fv
1
COMPRESSION
PERPENDICULAR
TO GRAIN
Fc┴
1
COMPRESSION
PARALLEL
TO GRAIN
Fc//
1
MODULUS
OF
ELASTICITY
E1
× 106
VERTICAL
LOAD
TRANSFER
CAPACITY
LATERAL LOAD
TRANSFER
CAPACITY
91
/4 - 91
/2
10 ¼ - 117
/8
12 ¼ - 14
16 -- -- -- -- -- --
SPAN : When Relam-LFS
®
Rimboard is used as a beam / header or to span openings, calculate allowable span using values listed herein.
NOTES 1. Not adjusted for end use.
2. The listed value of Ft is for a length of 24-inches or less. For up to 24-feet lengths, calculate allowable tensile
stress Ft' at Length L, using: Ft' = (24 / L)0.15 × Ft, where L = Length of member and Ft = listed value herein.
3. Acceptable for use as rafters, beams, headers, studs, columns, wall plates, joists, rimboard and wood trusses.
James A. Rothman, P.E.
Sr. Vice President - Q.C.
PFS Corporation
No
1278
Prepared by
Date
425 1,600 1,5
POUND PER SQUARE INCH - PSI
11
/4
and
11
/2
1,250 1,300 135
INCHES
RELAM - LFS ®
(LAMINATED FLOOR SYSTEM)
RELAM - LFS ®
RIMBOARD
1,300 135 425 1,600
PLF
1,5
1,600
MODULUS OF ELASTICITY
E1
× 106
POUND PER SQUARE INCH - PSI
17
/16
to
11
/2
1,300 135
17
/16
to
11
/2
425
LAMCO FOREST PRODUCTS
Listed Engineered Products 3
2,560 260
RELAM ®
- STRUCTURAL COMPONENTS
MODULUS OF ELASTICITY
E1
× 106
INCHES POUND PER SQUARE INCH - PSI
1,6
INCHES
9/21/06
4. BUILDING COMPONENT ACCEPTANCE REPORT NO1278
Certificate of
Conformance
LAMCO Forest Products, Inc.
Québec, Canada
This certifies that “Relam® & Relam-LFS® – Structural Components” bearing the PFS trademark
as listed in PFS BCAR 1278 has been manufactured under a quality assurance program
accepted by PFS and evaluated using ASTM D 5456 Standard Specification for Evaluation of
Structural Composite Lumber Products as referenced in the 2003 International Building Code®
(IBC) Section 2303.1.9 for Structural Composite Lumber.
For PFS Corporation
This product bears this certification mark –
the PFS mark of quality James A. Rothman, P.E.
Sr. Vice President – Quality Control
5. BUILDING COMPONENT ACCEPTANCE REPORT NO1278
Certificate of
Conformance
LAMCO Forest Products, Inc.
Québec, Canada
This certifies that “Relam-LFS® Engineered Rimboard” bearing the PFS trademark as listed
in PFS BCAR 1278 has been manufactured under a quality assurance program accepted
by PFS for compliance to ICC-ES Acceptance Criteria for Rim Board Products (AC124) as
referenced by ICC-ES under the 2003 International Building Code® (IBC).
For PFS Corporation
This product bears this certification mark –
the PFS mark of quality James A. Rothman, P.E.
Sr. Vice President – Quality Control
6. BUILDING COMPONENT ACCEPTANCE REPORT NO1278
Certificate of
Conformance
LAMCO Forest Products, Inc.
Québec, Canada
This certifies that “Relam® & Relam-LFS® – Structural Components” bearing the PFS
trademark as listed in PFS BCAR 1278 has been manufactured under a quality assurance
program accepted by PFS and evaluated using ASTM D 5456 Standard Specification for
Evaluation of Structural Composite Lumber Products as accepted in Appendix A of the
National Building Code of Canada (NBC).
For PFS Corporation
This product bears this certification mark –
the PFS mark of quality James A. Rothman, P.E.
Sr. Vice President – Quality Control
7. BUILDING COMPONENT ACCEPTANCE REPORT NO1278
Certificate of
Conformance
LAMCO Forest Products, Inc.
Québec, Canada
This certifies that “Relam-LFS® Engineered Rimboard” bearing the PFS trademark as listed
in PFS BCAR 1278 has been manufactured under a quality assurance program accepted
by PFS for compliance to ICC-ES Acceptance Criteria for Rim Board Products (AC124) as
accepted in Appendix A of the National Building Code of Canada (NBC).
For PFS Corporation
This product bears this certification mark –
the PFS mark of quality James A. Rothman, P.E.
Sr. Vice President – Quality Control