Caterpillar Cat D8T TRACK-TYPE TRACTOR Dozer Bulldozer (Prefix FMC) Service Repair Manual Instant Download.pdf

Service Repair Manual
Models
D8T TRACK-TYPE TRACTOR

Shutdown SIS
Previous Screen
Product: TRACK-TYPE TRACTOR
Model: D8T TRACK-TYPE TRACTOR FMC
Configuration: D8T TRACK-TYPE TRACTOR FMC00001-UP (MACHINE) POWERED BY C15 Engine
Disassembly and Assembly
D8T Track-Type Tractor Power Train
Media Number -UENR1388-02 Publication Date -01/03/2016 Date Updated -09/03/2016
i07232517
Final Drive Planetary Carrier (In Chassis) - Remove and
Install
SMCS - 4092-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Description Qty
A 3B-2968 Bolt 3
B 439-3939 Link Bracket As 1
C 439-3938 Link Bracket 1
1. Rotate the final drive until the drain plug is at the bottom.
2. Drain the final drive oil. Refer to Operation and Maintenance Manual, "Final Drive -
Change" for the correct draining and filling procedures.
3. Remove the outer axle. Refer to Disassembly and Assembly, "Axle - Remove and Install".
1/4
D8T TRACK-TYPE TRACTOR FMC00001-UP (MACHINE) POWERED BY C15 E...
2020/1/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

Illustration 1 g06321307
Note: Tooling (A) must be installed to a depth of 25 mm (1.0 inch) to hold the planetary
carrier.
4. Remove three equally spaced bolts (1) and install Tooling (A).
5. Remove the remaining bolts (1).
6. Position outer planetary carrier (2) away from the hub allowing enough room to install
Tooling (B).
7. Install Tooling (B) and a suitable lifting device to outer planetary carrier (2). The weight of
outer planetary carrier (2) is approximately 124 kg (273 lb).
8. Remove Tooling (A).
Note: Inner planetary carrier and sun gear (3) are to stay in the hub while outer planetary
carrier (2) is being removed.
9. Use a suitable pry bar at the bottom of outer planetary carrier (2) to help keep outer
planetary carrier (2) aligned straight with the hub during the removal process.
10. Remove outer planetary carrier (2).
2/4
2020/1/16

11. Remove O-ring seal (4) from outer planetary carrier (2).
12. Attach Tooling (C) to inner planetary carrier and sun gear (3). The weight of inner planetary
carrier and sun gear (3) is approximately 52 kg (115 lb).
13. Use a suitable pry bar in the center of inner planetary carrier and sun gear (3) to help keep
inner planetary carrier and sun gear (3) aligned straight with the hub during the removal
process.
14. Remove inner planetary carrier and sun gear (3).
3/4
2020/1/16

15. Remove thrust ring (5) and O-ring seal (6).
16. Remove lip seal (7).
Installation Procedure
1. Install outer planetary carrier (2) and inner planetary carrier and sun gear (3) in the reverse
order of removal.
a. Install lip seal (7) in the direction indicated in Illustration 7 towards the center of the
machine.
b. Lubricate the lip of lip seal (7) with lubricant being sealed.
c. Tighten bolts (1) to a torque of 430 ± 60 N·m (320 ± 45 lb ft).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jan 16 09:18:16 UTC+0800 2020
4/4
2020/1/16

Shutdown SIS
Previous Screen
i07232534
Final Drive, Steering Planetary, and Brake (Right Side) -
Remove and Install
SMCS - 4050-010-RI; 4132-010-RI
Removal Procedure
Table 1
Required Tools
A
142-6893 Adjustable Hook Gp 1
142-1666 Bracket As 1
1D-4615 Bolt 3
2J-3506 Full Nut 3
5P-8248 Washer 6
B - SAE 30 -
Start By:
a. Separate the track.
b. Remove the axles.
1/3
2020/1/16

Typical Example
1. Attach a suitable lifting device to Tooling (A).
2. Remove seven bolts (1) and install Tooling (A) to final drive, steering planetary, and brake
(2). The weight of final drive, steering planetary, and brake (2) is approximately 794 kg
(1750 lb).
Note: Bolts (4) hold the final drive, the planetary assembly, and the brake together.
3. Remove bolts (3) and (5). Do not remove bolts (4).
2/3
2020/1/16

Typical Example
4. Remove final drive, steering planetary, and brake (2).
5. Remove O-ring seals (6) and O-ring seal (7) from final drive, steering planetary, and brake
(2).
Installation Procedure
1. Install final drive, steering planetary, and brake (2) in the reverse order of removal.
a. Tighten bolts (3) to a torque of 800 ± 90 N·m (590 ± 66 lb ft).
b. Lubricate the washer faces, the nut faces, the faces for bolts (1), and the threads for
bolts (1) with Tooling (B).
c. Tighten bolts (1) to a torque of 300 ± 50 N·m (220 ± 37 lb ft). Then, tighten bolts (1)
for another 120° ± 5°.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jan 16 09:19:15 UTC+0800 2020
3/3
2020/1/16

Shutdown SIS
Previous Screen
i07232577
Steering Planetary and Brake - Disassemble
SMCS - 4132-015
Disassembly Procedure
Table 1
Required Tools
A 439-3940 Bracket As 3
B 1P-0520 Driver Group 1
C -
Forcing Bolts
3/8 by 16
3
Start By:
a. Remove the right side final drive, the planetary group, and the brake.
1/16
2020/1/16

2/16
2020/1/16

1. Remove bolts (1) that hold the planetary assembly and brake (2) to final drive (3).
2. Install Tooling (C). Tighten Tooling (C) evenly to remove planetary assembly and brake (2)
from final drive (3). Remove Tooling (C).
3/16
2020/1/16

3. Attach Tooling (A) and a suitable lifting device to planetary assembly and brake (2). The
weight of planetary assembly and brake (2) is approximately 136 kg (300 lb). Remove
planetary assembly and brake (2) from final drive (3).
4/16
2020/1/16

Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
4. Remove bolts (4).
5. Remove ring gear (5) from housing (6).
5/16
2020/1/16

6. Remove friction discs and brake plates (7) from housing (6).
6/16
2020/1/16

7. Remove bolts (8) and remove thrust disc (9) from housing (6).
7/16
2020/1/16

8. Use Tooling (B) and a suitable press to remove planetary carrier (11) from housing (6).
Note: Do not allow carrier (11) to fall when planetary carrier (11) is pressed from housing
(6).
Note: If a shim pack is present between the plate (9) and planetary carrier (11). Reuse the
same shim pack during assembly only if reusing the same planetary carrier (11). If a new
planetary carrier (11) is being used the shim pack should be discarded.
9. Remove bearing cone (10) (not shown) from housing (6).
8/16
2020/1/16

10. Remove ring (14) from planetary carrier (12).
11. Remove bolts (15).
12. Remove slinger (13) from planetary carrier (12).
13. If necessary, remove bearing cone (16) from planetary carrier (12).
Note: Bearing cone (16) will be destroyed during removal.
9/16
2020/1/16

14. Push pin (18) into shaft (17).
10/16
D8T TRACK-TYPE TRACTOR FMC00001-UP (MACHINE) POWERED BY C15...
2020/1/16

15. Remove shaft (17), gear (20), discs (22), and bearings (21) from planetary carrier (12).
16. Remove pin (18) from shaft (17).
17. Repeat Steps 14 through 16 for the two remaining planetary gears.
18. Remove ring gear (19) from planetary carrier (12).
11/16
2020/1/16

Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
19. Remove bolts (25) from housing (6).
20. Remove retainer (23) from piston (24).
12/16
2020/1/16

Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading

21. If necessary, remove bearing cups (26) from retainer (23).
22. Remove seal ring (27) from retainer (23).
13/16
2020/1/16

Caterpillar Cat D8T TRACK-TYPE TRACTOR Dozer Bulldozer (Prefix FMC) Service Repair Manual Instant Download.pdf

Recommended

Recommended

More Related Content

More from iudjkskmmd

More from iudjkskmmd (20)

Recently uploaded

Recently uploaded (20)

Caterpillar Cat D8T TRACK-TYPE TRACTOR Dozer Bulldozer (Prefix FMC) Service Repair Manual Instant Download.pdf