Successfully reported this slideshow.
We use your LinkedIn profile and activity data to personalize ads and to show you more relevant ads. You can change your ad preferences anytime.

Teradek 6.2.3 release_notes

886 views

Published on

Teradek Cube firmware notes

Published in: Devices & Hardware
  • Be the first to comment

  • Be the first to like this

Teradek 6.2.3 release_notes

  1. 1. Teradek Cube/Brik Firmware Version 6.2.3 Release Notes page 1 of 9New Features • NoneChanges • NoneBug Fixes • De-interlacer was not being enabled for SD resolutions • Fixed audio issues and video bitrate spikes while streaming static content • HLS was not working on newer Cube models • Fixed an audio clicking issue with BRIK. Requires FPGA version 3 • Proxy recording file durations were shorter than original clipsSupport forum: http://forum.teradek.com email: support@teradek.com phone: 888-941-2111
  2. 2. Teradek Cube/Brik Firmware Version 6.2.3 Release Notes page 2 of 9New Features – 6.2.1 • NoneChanges – 6.2.1 • The Original Livestream option can now be found under Live Internet Streaming settings • Moved less commonly used encoder and decoder controls to advanced settings • Encoder now restarts when resolution is changed in Live Internet Streaming mode to prevent issues with web-based players • Various Transport Stream changes/improvementsBug Fixes – 6.2.1 • Proxy recording did not work when audio was disabled • Stream Settings page did not load under IE8 • Cubes paired with Case used the wrong button mode by default • RTMP auto-start failed in some cases • RTMP status would sometimes be displayed incorrectly on OLED display • Network Configuration page incorrectly handled blank password fields • iOS6 users could not log into web UI through TeraCentral appSupport forum: http://forum.teradek.com email: support@teradek.com phone: 888-941-2111
  3. 3. Teradek Cube/Brik Firmware Version 6.2.3 Release Notes page 3 of 9New Features – 6.2.0 • Added native support for Ustream • Added native support for the New Livestream • Added additional encoder resolutions (480x270, 640x360, 854x480, 1024x576) • Expanded front panel menus to include Stream Settings, Device Settings, Bonding, and additional Network Configuration options • Added support for Link • Added Bonding page for Link/Bond configuration • Port-Based bitrate limits added for Link/Bond (requires Bond 6.2 firmware) • Port-Based primary/backup settings added for Link/Bond (requires Bond 6.2 firmware)Changes – 6.2.0 • Allow scanning for wireless networks from the front panel while in Master Mode • Assorted minor changes to web UI labels/options for consistency • Increased maximum string length for RTMP URLs • Added auto mode for Adaptive frame rate and removed minimum frame rate and priority options from web UI • USB or SD media is mounted sooner on boot upBug Fixes – 6.2.0 • RTMP status was sometimes incorrect on Broadcast LED • No front panel indication when a factory reset is initialized by the reset button • Network Configuration page incorrectly handled blank password fieldsSupport forum: http://forum.teradek.com email: support@teradek.com phone: 888-941-2111
  4. 4. Teradek Cube/Brik Firmware Version 6.2.3 Release Notes page 4 of 9New Features – 6.1.6 • Added options to disable front panel and USB support to improve performance with ZiXi streamingChanges – 6.1.6 • ZiXi configuration page updates – added instructions to pages • Remove ZiXi cloud server option (no longer valid)Bug Fixes – 6.1.6 • RTMP auto-start sometimes failed on device boot up • Blank fields in Bond custom modem configuration did not apply correctlySupport forum: http://forum.teradek.com email: support@teradek.com phone: 888-941-2111
  5. 5. Teradek Cube/Brik Firmware Version 6.2.3 Release Notes page 5 of 9New Features – 6.1.5 • NoneChanges – 6.1.5 • Encoding profile restricted to Main or lower for Livestream mode • Removed timer from front panel when broadcastingBug Fixes – 6.1.5 • Fixed issues with long-term RTMP broadcasting • Bond universal license did not work correctlySupport forum: http://forum.teradek.com email: support@teradek.com phone: 888-941-2111
  6. 6. Teradek Cube/Brik Firmware Version 6.2.3 Release Notes page 6 of 9New Features – 6.1.3 • Add ‘Ignore Audio Phase’ to the Device Settings page. Enable to improve compatibility with RED Epic/Scarlet and Arri Alexa SDI audio • Add option to set DHCP range in Master mode • Add support for new firmware detection and one-click installation • Add encoding frame structure optionChanges – 6.1.3 • Bonding and Quickview RTP Push features can be enabled with universal licenses • Warning appears if no recovery image is detected • Modem preset defaults to disabled on CubeBug Fixes – 6.1.3 • RTMP broadcasts no longer restart after a short time • RTMP stream audio now compatible with Livestream recordings • Improved audio when streaming RTMP to mobile devices • Fixed Brik SD-SDI support • HDMI encoders no longer hang at boot up • Fixed Decoder Settings page compatibility with IE 8Support forum: http://forum.teradek.com email: support@teradek.com phone: 888-941-2111
  7. 7. Teradek Cube/Brik Firmware Version 6.2.3 Release Notes page 7 of 9New Features – 6.1.2 • Added audio sample rate settings for the Cube DecodersBug Fixes – 6.1.2 • Fixed Setup Wizard on Cube 5xx models • Fixed issue with Cube connecting to unsecured wireless networks • Fixed intermittent freezing startup issues on Cube EncodersSupport forum: http://forum.teradek.com email: support@teradek.com phone: 888-941-2111
  8. 8. Teradek Cube/Brik Firmware Version 6.2.3 Release Notes page 8 of 9New Features – 6.1.1 • MPEG-TS Demo License is available upon request.Bug Fixes – 6.1.1 • Transport stream server port unable to be configured on decoders • Framerate would not encode above 30 fps unless factory reset was performed • Updated wireless settings webpage for older Cubes • Fixed issues with using Vodafone modem • Fixed DSLR mode for Cube 255 • Updated Bond custom modem settings webpage to work with Bond 5.3.2 • Updated Cube custom modem webpage • Fixed Master Mode password being changed each time the webpage is applied • LCD menu now shows currently selected WiFi channel • Fixed Decoder setup and Output setup on Decoder LCD in which the settings were not being appliedSupport forum: http://forum.teradek.com email: support@teradek.com phone: 888-941-2111
  9. 9. Teradek Cube/Brik Firmware Version 6.2.3 Release Notes page 9 of 9New Features – 6.1.0 • Added USB and SD card recording • Added ZiXi integration • Added ‘Auto’ setting for the encoder output resolution • Added support for Brik productChanges – 6.1.0 • Deinterlacer option moved to Device Settings page • Changed Encoder Settings page layout • Decoder reconnection improvements in Automatic mode • Improved special character support for various configuration optionsBug Fixes – 6.1.0 • Proxy recording missed stop signals • Clip names now use correct camera position when used with RED cameras • Recorded files used baseline profile only • Recorded file headers were incompatible with some players • Recording status on front panel display was sometimes out of sync with actual status • Encoder failed to start when output resolution scaled to SD or below • Decoder became unresponsive when idle for long periods • Fixed Hexadecimal password configuration for WEP secured Wifi networksSupport forum: http://forum.teradek.com email: support@teradek.com phone: 888-941-2111
  10. 10. Teradek Cube/Brik Firmware Version 6.2.3 Release Notes page 9 of 9New Features – 6.1.0 • Added USB and SD card recording • Added ZiXi integration • Added ‘Auto’ setting for the encoder output resolution • Added support for Brik productChanges – 6.1.0 • Deinterlacer option moved to Device Settings page • Changed Encoder Settings page layout • Decoder reconnection improvements in Automatic mode • Improved special character support for various configuration optionsBug Fixes – 6.1.0 • Proxy recording missed stop signals • Clip names now use correct camera position when used with RED cameras • Recorded files used baseline profile only • Recorded file headers were incompatible with some players • Recording status on front panel display was sometimes out of sync with actual status • Encoder failed to start when output resolution scaled to SD or below • Decoder became unresponsive when idle for long periods • Fixed Hexadecimal password configuration for WEP secured Wifi networksSupport forum: http://forum.teradek.com email: support@teradek.com phone: 888-941-2111

×