The document provides instructions for disassembling and assembling components of a track-type tractor's power train. It describes in detail how to disassemble a torque converter by removing its various plates, discs, bearings, and seals. It then explains how to assemble the torque converter by reversing the removal steps. Additionally, it outlines how to separate the transmission and bevel gears from the rest of the tractor and how to reconnect them.
2. Shutdown SIS
Previous Screen
Product: TRACK-TYPE TRACTOR
Model: D6N LGP TRACK-TYPE TRACTOR SGG
Configuration: D6N XL, LGP TRACK-TYPE TRACTOR SGG00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
D6N Track-Type Tractor Power Train
Media Number -UENR4080-03 Publication Date -01/09/2015 Date Updated -31/07/2018
i07021596
Torque Converter - Disassemble
SMCS - 3101-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8T-4172 Bolt 2
B 1P-0510 Driver Gp 1
C 8H-0663 Bearing Puller Gp 1
Start By:
a. Remove the torque converter.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
1/9
D6N XL, LGP TRACK-TYPE TRACTOR SGG00001-UP (MACHINE) POWERED ...
2021/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Note: Cleanliness is an important factor. Before the disassembly procedure, ensure that the
exterior of the component is clean to prevent dirt from entering the internal mechanism. Dirt and
contaminants can damage the precision components.
Illustration 1 g03862684
1. Place the torque converter assembly on suitable cribbing. Remove bolts (1).
Illustration 2 g03862695
2. Install Tooling (A). Tighten Tooling (A) to separate housing assembly (2) and impeller
assembly (3).
2/9
D6N XL, LGP TRACK-TYPE TRACTOR SGG00001-UP (MACHINE) POWERED ...
2021/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g06195011
Illustration 4 g03862702
3. Remove spline plate (4) and reaction plate (4A).
Note: Note the orientation of the discs.
4. Remove piston (5), separator plate (6A), and friction disc (6).
3/9
D6N XL, LGP TRACK-TYPE TRACTOR SGG00001-UP (MACHINE) POWERED ...
2021/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 5 g03862896
5. Remove spline plate (7) and converter turbine (8) as a unit.
Illustration 6 g03862904
6. Remove bearing (9). Remove bolts (10). Remove spline plate (7) from converter turbine (8).
4/9
D6N XL, LGP TRACK-TYPE TRACTOR SGG00001-UP (MACHINE) POWERED ...
2021/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 14 g03863284
13. Use a suitable press to remove shaft assembly (22) from carrier assembly (23).
Illustration 15 g03863336
14. Remove seals (24) from shaft assembly (22).
Illustration 16 g03863327
15. Use Tooling (B) and a suitable press to remove bearing (25) (not shown) from carrier
assembly (23).
8/9
D6N XL, LGP TRACK-TYPE TRACTOR SGG00001-UP (MACHINE) POWERED ...
2021/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 17 g03863346
16. Remove lip seal (26), retaining ring (27), and shaft assembly (28) from stator assembly (29).
Illustration 18 g03863398
17. Use Tooling (C) and a suitable press to remove bearing (30) from shaft assembly (28).
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Nov 26 12:12:10 UTC+0800 2021
9/9
D6N XL, LGP TRACK-TYPE TRACTOR SGG00001-UP (MACHINE) POWERED ...
2021/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: TRACK-TYPE TRACTOR
Model: D6N LGP TRACK-TYPE TRACTOR SGG
Configuration: D6N XL, LGP TRACK-TYPE TRACTOR SGG00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
D6N Track-Type Tractor Power Train
Media Number -UENR4080-03 Publication Date -01/09/2015 Date Updated -31/07/2018
i07004929
Torque Converter - Assemble
SMCS - 3101-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
B 1P-0510 Driver Gp 1
D - Loctite 536 Low Break Loose Pipe Sealant 1
E 330-9910 Adapter Frame 1
Illustration 1 g03865788
1. Use a suitable press to install bearing (30) onto shaft assembly (28).
1/9
D6N XL, LGP TRACK-TYPE TRACTOR SGG00001-UP (MACHINE) POWERED ...
2021/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 2 g03865683
2. Apply Tooling (D) to the bore and install lip seal (26) into stator assembly (29) within ±
0.63 mm (0.025 inch) of the surface. Install shaft assembly (28) into stator assembly (29).
Install retaining ring (27).
Illustration 3 g03865190
3. Use Tooling (B) and a suitable press to install bearing (25) into carrier assembly (23).
2/9
D6N XL, LGP TRACK-TYPE TRACTOR SGG00001-UP (MACHINE) POWERED ...
2021/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 4 g03863336
4. Install seals (24) into shaft assembly (22).
Illustration 5 g03865589
5. Use a suitable press to install shaft assembly (22) into carrier assembly (23).
Illustration 6 g03863260
6. Install retaining ring (21) onto shaft (22).
3/9
D6N XL, LGP TRACK-TYPE TRACTOR SGG00001-UP (MACHINE) POWERED ...
2021/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 7 g03865524
7. Use Tooling (E) and a suitable press to install stator assembly (29) and carrier assembly
(23) onto shaft assembly (28).
Illustration 8 g03865591
4/9
D6N XL, LGP TRACK-TYPE TRACTOR SGG00001-UP (MACHINE) POWERED ...
2021/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 12 g06194934
10. Raise the temperature of stator (12) to 135° C (275° F).
11. Lower the temperature of cam (15A) to −40° C (−40° F). Install cam (15A) into stator (12)
with impeller side marking up as shown in illustration 11.
12. Install inner race (15).
13. Install rollers (16) and springs (17).
Note: Install springs (17) in larger side of the cam pocket with maximum number of loops
towards outside as shown in Illustration 12.
Illustration 13 g06194935
14. Install thrust washer (14) and retaining ring (13).
6/9
D6N XL, LGP TRACK-TYPE TRACTOR SGG00001-UP (MACHINE) POWERED ...
2021/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 16 g06195011
17. Install converter turbine (8) and spline plate (7) as a unit into the housing assembly.
18. Install reaction plate (4A) and spline plate (4).
19. Install friction disc (6) and separator plate (6A).
Illustration 17 g06194936
20. Install piston (5) into housing assembly (2).
8/9
D6N XL, LGP TRACK-TYPE TRACTOR SGG00001-UP (MACHINE) POWERED ...
2021/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 18 g03865618
21. Install housing assembly (2) onto impeller assembly (3). Install bolts (1). Tighten bolts (1)
to a torque of 60 ± 7 N·m (44 ± 5 lb ft).
End By:
a. Install the torque converter.
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Nov 26 12:13:06 UTC+0800 2021
9/9
D6N XL, LGP TRACK-TYPE TRACTOR SGG00001-UP (MACHINE) POWERED ...
2021/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Shutdown SIS
Previous Screen
Product: TRACK-TYPE TRACTOR
Model: D6N LGP TRACK-TYPE TRACTOR SGG
Configuration: D6N XL, LGP TRACK-TYPE TRACTOR SGG00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
D6N Track-Type Tractor Power Train
Media Number -UENR4080-03 Publication Date -01/09/2015 Date Updated -31/07/2018
i06237845
Transmission and Bevel Gears - Separate and Connect
SMCS - 3010-029
Separation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 439-3940 Link Bracket 2
Start By:
a. Remove the transmission and bevel gears.
Illustration 1 g02559163
1. Position transmission and bevel gears (1) on Tooling (A).
1/3
D6N XL, LGP TRACK-TYPE TRACTOR SGG00001-UP (MACHINE) POWERED ...
2021/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 5 g02560156
5. Remove bevel and transfer gears (5). The weight of bevel and transfer gears (5) is
approximately 249 kg (550 lb).
Connection Procedure
1. Install bevel gears (5) and transmission in the reverse order of removal.
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Nov 26 12:14:02 UTC+0800 2021
3/3
D6N XL, LGP TRACK-TYPE TRACTOR SGG00001-UP (MACHINE) POWERED ...
2021/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Shutdown SIS
Previous Screen
Product: TRACK-TYPE TRACTOR
Model: D6N LGP TRACK-TYPE TRACTOR SGG
Configuration: D6N XL, LGP TRACK-TYPE TRACTOR SGG00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
D6N Track-Type Tractor Power Train
Media Number -UENR4080-03 Publication Date -01/09/2015 Date Updated -31/07/2018
i04670350
Bevel and Transfer Gears - Disassemble
SMCS - 3011-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 5F-7343 Bearing Puller Gp 1
C 8T-2839 Spanner Wrench 1
Start By:
a. Separate the transmission and bevel gears. Refer to Disassembly and Assembly,
"Transmission and Bevel Gears - Separate".
1/13
D6N XL, LGP TRACK-TYPE TRACTOR SGG00001-UP (MACHINE) POWERED ...
2021/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 5 g00954584
6. Remove bolts (8). Use two bolts (8) in order to remove cage (9).
7. Remove shims (10).
Illustration 6 g00994151
8. Remove O-ring seal (12), seal (11), bearing (14), and bearing cup (13) from cage (9).
4/13
D6N XL, LGP TRACK-TYPE TRACTOR SGG00001-UP (MACHINE) POWERED ...
2021/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 7 g00994324
9. Remove bolts (15), cover (16), and shims (17).
Illustration 8 g00954587
10. Remove bolts (18). Use two bolts (18) in order to remove cover (19). Tighten bolts (18)
evenly and remove cover (19).
5/13
D6N XL, LGP TRACK-TYPE TRACTOR SGG00001-UP (MACHINE) POWERED ...
2021/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Illustration 9 g00994154
11. If necessary, remove dowels (20) and bearing cup (21) from cover (19).
Illustration 10 g00954590
Note: Gears (22) and (23) must be removed from the case assembly at the same time.
12. Remove gear (22) and gear (23) from the case assembly.
6/13
D6N XL, LGP TRACK-TYPE TRACTOR SGG00001-UP (MACHINE) POWERED ...
2021/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. Illustration 11 g00954593
Note: Bearing cones (24) must be destroyed in order to remove the cones from the gear.
13. Remove bearing cones (24) from gear (22).
Illustration 12 g00994158
14. Remove bolt (25) and retainer (26) from gear (23).
7/13
D6N XL, LGP TRACK-TYPE TRACTOR SGG00001-UP (MACHINE) POWERED ...
2021/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
30. Illustration 13 g00954591
15. Use Tooling (B) and a suitable press in order to remove bearing cone (27) from gear (28).
Illustration 14 g00994331
16. Use a suitable press in order to remove bearing cone (29) from gear (28) and from gear (23).
8/13
D6N XL, LGP TRACK-TYPE TRACTOR SGG00001-UP (MACHINE) POWERED ...
2021/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
31. Illustration 15 g00954857
17. Remove bearing cups (30) from case (31).
Illustration 16 g00994147
18. Bend the tab on lock ring (33) away from nut (32).
9/13
D6N XL, LGP TRACK-TYPE TRACTOR SGG00001-UP (MACHINE) POWERED ...
2021/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
32. Note: Use a new lock ring (33) during assembly.
19. Use Tooling (C) in order to remove nut (32).
20. Remove washer (34) and bearing cone (34A).
Illustration 17 g01233575
21. Attach a suitable lifting device to shaft assembly (35). The weight of shaft assembly (35) is
approximately 39 kg (86 lb).
22. Remove shaft assembly (35).
Illustration 18 g00954861
23. Remove bolts (36) and gear (37).
10/13
D6N XL, LGP TRACK-TYPE TRACTOR SGG00001-UP (MACHINE) POWERE...
2021/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
33. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
34. Illustration 19 g00954863
24. Remove the race and roller bearing (38) from shaft assembly (35).
Illustration 20 g00994148
25. Remove bolts (39), cage (40), and shims (41).
11/13
D6N XL, LGP TRACK-TYPE TRACTOR SGG00001-UP (MACHINE) POWERE...
2021/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
35. Illustration 21 g00994149
26. Remove bearing cone (46), bearing cups (45) and (42), and carrier (44).
27. Remove rings (43) from carrier (44).
Illustration 22 g00994563
28. Remove bearing cup (47) from case (31).
12/13
D6N XL, LGP TRACK-TYPE TRACTOR SGG00001-UP (MACHINE) POWERE...
2021/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...