This document provides instructions for removing and installing valve stem seals on Caterpillar 320, 320L, and 320N track-type excavators. The procedure involves using a seal pick tool to remove the old seals from the valve guides and install new seals. Technicians are instructed to keep all parts clean and coat the new seals with engine oil during installation.
The document provides assembly instructions for installing a swing gear and bearing on an excavator. It lists required tools and parts. The procedure involves cleaning the swing gear and bearing, applying lubricant and sealant, lifting it into position using links, and securing it with bolts torqued to specification. Inner and outer dust seals are installed in seal grooves before completing reassembly of the undercarriage frame.
The document provides instructions for removing and installing a fuel injection pump on a 320DL excavator with a C6.4 engine. It describes:
1) Removing components like hoses, tubes, brackets and gears to access the fuel injection pump.
2) Using identification marks and tooling to properly align gears during removal and installation.
3) Cleaning components thoroughly before installation to prevent contamination.
4) Installing the fuel injection pump by reversing the removal steps and ensuring proper torque of fasteners.
Caterpillar cat 320 d ln excavator (prefix wbn) service repair manual (wbn000...fkjsekksmem
This document provides the procedure for removing and installing inlet and exhaust valve springs on a Caterpillar 320D LN excavator with a C6.4 engine. It describes using special tools to compress the valve springs and rotate the crankshaft to position the piston for safe removal and installation of the springs. Proper cleaning and inspection of parts is emphasized to prevent damage and wear. The process involves removing keepers and other components to access the springs which must be replaced in matched pairs per cylinder.
Caterpillar cat 329 dl mobile hyd power unit excavator (prefix j8d) service r...ifse9diodkdk
The document provides instructions for disassembling the final drive of a 329DL Mobile Hydraulic Power Unit. It lists required tools and describes a 37 step process involving removing housing, gears, carriers, shafts, seals, and other components. Cleanliness is important to prevent dirt from entering during reassembly. Weights of removed parts are provided to assist with lifting.
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. Key steps include:
1. Using tooling to compress the valve spring and rotate the crankshaft to allow the piston to hold the valve open while the spring is removed.
2. Removing the valve keepers and spring retainer to access the valve spring.
3. Reversing the process to install new valve springs, making sure to complete installation on pairs of cylinders before moving to the next pair.
Caterpillar cat 323 e l excavator (prefix yrp) service repair manual (yrp0000...fjskefkemms
This document provides instructions for servicing the final drive of excavator models 323E L, 323E LN, and 323E SA. It includes procedures for disassembling and removing components like the final drive, carrier assembly, ring gears, and seals. It also provides instructions for reassembling these components, including installing seals, bearings, and gears, and using shims to set proper bearing preload. Bolts and seals must be tightened to the specified torques.
The document provides instructions for removing and installing various engine components on a Caterpillar 330D2 excavator, including the engine oil pump, water pump, water temperature regulator, and flywheel. The procedures note required tools and safety precautions. Components must be clean and free of damage, with replacement of worn parts. Proper torque values are specified for reinstallation of components.
Caterpillar cat 320 d l excavator (prefix kgf) service repair manual (kgf0000...fkjsekksmem
This document provides instructions for disassembling and assembling the travel motor of a 320D L excavator. The disassembly process includes 27 steps to remove components like the head, fittings, seals, brake piston, plates, and barrel assembly. The assembly section outlines 13 steps including installing seals, keys, cam plate, springs, and piston shoe assemblies back into the barrel assembly and body of the travel motor. Special care must be taken to align parts properly and not allow components to separate during disassembly and assembly.
The document provides assembly instructions for installing a swing gear and bearing on an excavator. It lists required tools and parts. The procedure involves cleaning the swing gear and bearing, applying lubricant and sealant, lifting it into position using links, and securing it with bolts torqued to specification. Inner and outer dust seals are installed in seal grooves before completing reassembly of the undercarriage frame.
The document provides instructions for removing and installing a fuel injection pump on a 320DL excavator with a C6.4 engine. It describes:
1) Removing components like hoses, tubes, brackets and gears to access the fuel injection pump.
2) Using identification marks and tooling to properly align gears during removal and installation.
3) Cleaning components thoroughly before installation to prevent contamination.
4) Installing the fuel injection pump by reversing the removal steps and ensuring proper torque of fasteners.
Caterpillar cat 320 d ln excavator (prefix wbn) service repair manual (wbn000...fkjsekksmem
This document provides the procedure for removing and installing inlet and exhaust valve springs on a Caterpillar 320D LN excavator with a C6.4 engine. It describes using special tools to compress the valve springs and rotate the crankshaft to position the piston for safe removal and installation of the springs. Proper cleaning and inspection of parts is emphasized to prevent damage and wear. The process involves removing keepers and other components to access the springs which must be replaced in matched pairs per cylinder.
Caterpillar cat 329 dl mobile hyd power unit excavator (prefix j8d) service r...ifse9diodkdk
The document provides instructions for disassembling the final drive of a 329DL Mobile Hydraulic Power Unit. It lists required tools and describes a 37 step process involving removing housing, gears, carriers, shafts, seals, and other components. Cleanliness is important to prevent dirt from entering during reassembly. Weights of removed parts are provided to assist with lifting.
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. Key steps include:
1. Using tooling to compress the valve spring and rotate the crankshaft to allow the piston to hold the valve open while the spring is removed.
2. Removing the valve keepers and spring retainer to access the valve spring.
3. Reversing the process to install new valve springs, making sure to complete installation on pairs of cylinders before moving to the next pair.
Caterpillar cat 323 e l excavator (prefix yrp) service repair manual (yrp0000...fjskefkemms
This document provides instructions for servicing the final drive of excavator models 323E L, 323E LN, and 323E SA. It includes procedures for disassembling and removing components like the final drive, carrier assembly, ring gears, and seals. It also provides instructions for reassembling these components, including installing seals, bearings, and gears, and using shims to set proper bearing preload. Bolts and seals must be tightened to the specified torques.
The document provides instructions for removing and installing various engine components on a Caterpillar 330D2 excavator, including the engine oil pump, water pump, water temperature regulator, and flywheel. The procedures note required tools and safety precautions. Components must be clean and free of damage, with replacement of worn parts. Proper torque values are specified for reinstallation of components.
Caterpillar cat 320 d l excavator (prefix kgf) service repair manual (kgf0000...fkjsekksmem
This document provides instructions for disassembling and assembling the travel motor of a 320D L excavator. The disassembly process includes 27 steps to remove components like the head, fittings, seals, brake piston, plates, and barrel assembly. The assembly section outlines 13 steps including installing seals, keys, cam plate, springs, and piston shoe assemblies back into the barrel assembly and body of the travel motor. Special care must be taken to align parts properly and not allow components to separate during disassembly and assembly.
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 320 excavator models. It describes the required tools and gives a step-by-step process including removing clips and pins, sliding tubes, and removing/installing parts like the governor, linkage, and seals using special tools. References are provided for more information on governors and linkage inspection procedures.
Caterpillar cat 336 e hvg excavator (prefix rbs) service repair manual (rbs00...f8isoeidkdk
The document provides instructions for installing a rear power take-off (RPTO) on a C9.3 engine. The procedure involves installing various components like a bearing, thrust washer, dowels, adapter assembly, idler gear and shaft. Tools like guide studs and driver groups are required. Torque specifications and the correct sequence are important to properly install the RPTO.
Caterpillar cat 323 e l excavator (prefix rap) service repair manual (rap0000...fjskefkemms
The document provides instructions for servicing the final drive of excavator models 323E L, 323E LN, and 323E SA. It includes steps to disassemble and remove the final drive components, such as the carrier assembly, ring gears, planetary gears, and seals. It also provides instructions for assembling the final drive, including pressing bearings into place, determining the correct shim thickness, installing seals and pins, and reassembling the carrier assembly. Tools required include lifting devices, presses, seal installers, and other specialized tools. Proper torque values and procedures are specified for reinstalling components.
Caterpillar cat 320 d lrr excavator (prefix hjc) service repair manual (hjc00...fjkskedmme
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes the required tools and multi-step procedures for removal and installation, which include removing other engine components, using specialty tools to remove the guides and seats, cleaning parts, and ensuring proper installation height or alignment. Safety notices are provided to keep parts clean and contain fluids properly during the process.
Caterpillar cat 323 d l excavator (prefix cwg) service repair manual (cwg0000...fjskksmem
The document provides instructions for removing and installing the crankshaft on a Caterpillar C6.4 engine. To remove the crankshaft, the front housing, rear seal, flywheel housing and oil pan must first be removed. Then the connecting rod caps, main bearing caps and pistons can be taken off to allow removal of the crankshaft. Installation follows the reverse order, with care taken to clean parts and apply specified torques. End play must be checked after installation is complete.
Caterpillar cat 329 e l excavator (prefix rld) service repair manual (rld0000...fikkskmmdm
This document provides instructions for disassembling and assembling a travel motor. It lists the required tools and gives step-by-step instructions to remove components like the head, brake piston, rotating assembly, seals and bearings. The assembly section then lists the components and provides the reverse steps to reinstall components and ensure proper alignment using tools and lubricants.
Caterpillar cat 329 e excavator (prefix k2l) service repair manual (k2l00001 ...fikkskmmdm
This document provides instructions for disassembling and assembling the travel motor of a 329E Mobile Hydraulic Power Unit. It lists 28 steps for disassembly, removing components like the head, brake piston, rotating assembly, and seals. It then lists 23 steps for assembly, reinstalling those components in reverse order while noting proper lubrication and alignment of parts. Tools required are also listed.
Caterpillar cat 320 d lrr excavator (prefix tae) service repair manual (tae00...fjsekdmmeed
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D LRR excavator engine. It describes using special tools to compress the valve springs, rotate the crankshaft, and remove the springs and related components. The installation section gives steps for cleaning, lubricating, and reinstalling the springs and seals in the proper order. Removal and installation of valve guides is also outlined.
Caterpillar cat 330 d2 l excavator (prefix szk) service repair manual (szk000...fjskkksmemm
This document provides instructions for disassembling and assembling the final drive of an excavator model 330D2 L. The disassembly process involves removing over 30 individual components in a specific sequence. This includes removing gears, shafts, bearings, seals, and housing components. The assembly process reverses the disassembly steps and provides details on cleaning, lubricating, and setting proper bearing preloads using shims. Special tools are required for tasks like installing dual-cone seals.
This document provides instructions for removing and installing various engine components on a Caterpillar 330 L excavator, including:
1. The cylinder head removal procedure involves removing fuel injection lines, exhaust manifold, rocker shaft and pushrods, and bolts holding the head to the cylinder block.
2. Installing the cylinder head requires cleaning surfaces, installing gaskets and bolts, adjusting valves, and reinstalling other removed components.
3. Removal of the spacer plate requires removing seals and installing a new gasket, while installation requires cleaning and installing the plate with new seals.
Caterpillar cat 330 b excavator (prefix 2rr) service repair manual (2rr00001 ...hfjsekekmmd
This document provides instructions for removing and reassembling the final drives on an excavator model 330B. The summary is:
1. The final drive is disassembled by removing components like the ring gear, carrier assemblies, planetary gears, and seals.
2. To reassemble, components are cleaned and seals/bearings installed before refitting parts like the carrier assemblies, ring gear and sprockets.
3. Precise measurements are taken to determine the correct shim thickness for installing the gear to achieve proper bearing preload.
Caterpillar cat 318 e l excavator (prefix dzf) service repair manual (dzf0000...fjskekdmjekm
The document provides instructions for removing and installing a crankshaft timing ring on a C4.4 engine. It describes:
1) Removing the crankshaft first according to a separate procedure.
2) Cleaning the crankshaft timing ring and inspecting it for wear or damage, replacing if needed.
3) Lubricating and installing the timing ring on the crankshaft, ensuring it is seated properly.
Caterpillar cat 330 c fm excavator (prefix b4n) service repair manual (b4n000...fjsjekdmmeme
This document provides instructions for servicing components of a Caterpillar 330C FM Excavator engine, including:
- Installing the cylinder head, which involves positioning a new gasket, attaching lifting tools to the head, applying anti-seize compound, and tightening bolts in a specific sequence.
- Removing and installing the camshaft, which requires removing other parts first like the rocker arm and front cover, then using hooks to position lifters and removing/installing the camshaft.
- Removing and installing the camshaft gear by first removing the camshaft, pressing it off the gear, heating the gear, and pressing it back onto the camshaft
Caterpillar cat 330 c l excavator (prefix jnk) service repair manual (jnk0000...hhjsekmdmm
The document provides installation instructions for a gear pump used in the fan drive of an excavator. It outlines 20 steps to assemble the piston motor that drives the hydraulic fan. These include pressing bearings onto shafts, installing springs, O-rings, seals, and housing components in the proper order and orientation. Precautions are given to ensure cleanliness and prevent injury from parts under pressure.
Caterpillar cat 16 g motor grader (prefix 93u) service repair manual (93u0267...fjsekdmmeed
This document provides instructions for removing and installing rocker shaft assemblies, push rods, valve lifters, and related components on a 3406C diesel engine. The key steps include:
1. Removing the valve covers, fuel lines, rocker shaft assemblies, push rods, and valve lifters. Identification marks should be made on removed parts.
2. Cleaning and lubricating replacement parts as needed before installation. Parts should be installed in their original locations when possible.
3. Installing the valve lifters, push rods, rocker shaft assemblies, fuel lines, adjusting the valves, and replacing the valve covers. Torque specifications and safety notices are provided throughout.
Caterpillar cat 390 f excavator (prefix hng) service repair manual (hng00001 ...fjskefksemer
This document provides instructions for removing and installing the front gear group of a C18 engine. The removal procedure involves removing 14 bolts, plates, gears and seals. Special care must be taken to mark gear orientations and not turn the crankshaft during removal. The installation procedure describes cleaning components, applying thread lock compound, installing 14 gears, plates and seals in the correct order and orientation, and adjusting backlash between gears. Proper removal and installation is important to avoid engine damage.
Caterpillar cat 330 c excavator (prefix gag) service repair manual (gag00001 ...hfjsekekmmd
1) The document provides instructions for disassembling and assembling the travel motor of a 330C excavator.
2) It describes 28 steps to disassemble the travel motor by removing components like the head, springs, plates, and seals.
3) It then describes 28 steps for reassembling the travel motor, placing components back in the reverse order and noting alignment and torque specifications.
Caterpillar cat 966 c wheel loader (prefix 18b) service repair manual (18b012...fjsjjekdkme
This document provides instructions for installing a fuel injection pump housing and governor on a Caterpillar 3306 engine. The steps include:
1. Ensuring the number 1 piston is at top center position for timing.
2. Installing alignment tools in the flywheel housing.
3. Checking valve timing and turning the flywheel until the number 1 piston is at the correct position.
4. Installing the fuel injection pump housing and governor according to the assembly procedure.
This document provides instructions for installing a flywheel and removing and installing a wet back end flywheel housing on a Caterpillar 320 GC excavator. It describes using guide studs and lifting devices to position the heavy flywheel and housing. Torque specifications and tightening sequences are given for installing mounting bolts. Replacing seals, gaskets and dowels is also covered.
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. The procedure involves using specialty tools to compress the valve springs so that the valves, springs, and related components can be safely accessed and removed or installed one piston at a time. Proper tool use and safety precautions are emphasized to avoid injury from released spring forces.
The document provides instructions for removing the fuel injection pump from a Caterpillar 320D L excavator with a C6.4 engine. It lists the required tools and safety notices, then gives a step-by-step procedure involving disconnecting fuel lines and harness assemblies, removing mounting hardware, and taking off the pump while keeping identification marks aligned for installation. Cleanliness is emphasized throughout to prevent contaminants from entering the system.
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 320 excavator models. It describes the required tools and gives a step-by-step process including removing clips and pins, sliding tubes, and removing/installing parts like the governor, linkage, and seals using special tools. References are provided for more information on governors and linkage inspection procedures.
Caterpillar cat 336 e hvg excavator (prefix rbs) service repair manual (rbs00...f8isoeidkdk
The document provides instructions for installing a rear power take-off (RPTO) on a C9.3 engine. The procedure involves installing various components like a bearing, thrust washer, dowels, adapter assembly, idler gear and shaft. Tools like guide studs and driver groups are required. Torque specifications and the correct sequence are important to properly install the RPTO.
Caterpillar cat 323 e l excavator (prefix rap) service repair manual (rap0000...fjskefkemms
The document provides instructions for servicing the final drive of excavator models 323E L, 323E LN, and 323E SA. It includes steps to disassemble and remove the final drive components, such as the carrier assembly, ring gears, planetary gears, and seals. It also provides instructions for assembling the final drive, including pressing bearings into place, determining the correct shim thickness, installing seals and pins, and reassembling the carrier assembly. Tools required include lifting devices, presses, seal installers, and other specialized tools. Proper torque values and procedures are specified for reinstalling components.
Caterpillar cat 320 d lrr excavator (prefix hjc) service repair manual (hjc00...fjkskedmme
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes the required tools and multi-step procedures for removal and installation, which include removing other engine components, using specialty tools to remove the guides and seats, cleaning parts, and ensuring proper installation height or alignment. Safety notices are provided to keep parts clean and contain fluids properly during the process.
Caterpillar cat 323 d l excavator (prefix cwg) service repair manual (cwg0000...fjskksmem
The document provides instructions for removing and installing the crankshaft on a Caterpillar C6.4 engine. To remove the crankshaft, the front housing, rear seal, flywheel housing and oil pan must first be removed. Then the connecting rod caps, main bearing caps and pistons can be taken off to allow removal of the crankshaft. Installation follows the reverse order, with care taken to clean parts and apply specified torques. End play must be checked after installation is complete.
Caterpillar cat 329 e l excavator (prefix rld) service repair manual (rld0000...fikkskmmdm
This document provides instructions for disassembling and assembling a travel motor. It lists the required tools and gives step-by-step instructions to remove components like the head, brake piston, rotating assembly, seals and bearings. The assembly section then lists the components and provides the reverse steps to reinstall components and ensure proper alignment using tools and lubricants.
Caterpillar cat 329 e excavator (prefix k2l) service repair manual (k2l00001 ...fikkskmmdm
This document provides instructions for disassembling and assembling the travel motor of a 329E Mobile Hydraulic Power Unit. It lists 28 steps for disassembly, removing components like the head, brake piston, rotating assembly, and seals. It then lists 23 steps for assembly, reinstalling those components in reverse order while noting proper lubrication and alignment of parts. Tools required are also listed.
Caterpillar cat 320 d lrr excavator (prefix tae) service repair manual (tae00...fjsekdmmeed
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D LRR excavator engine. It describes using special tools to compress the valve springs, rotate the crankshaft, and remove the springs and related components. The installation section gives steps for cleaning, lubricating, and reinstalling the springs and seals in the proper order. Removal and installation of valve guides is also outlined.
Caterpillar cat 330 d2 l excavator (prefix szk) service repair manual (szk000...fjskkksmemm
This document provides instructions for disassembling and assembling the final drive of an excavator model 330D2 L. The disassembly process involves removing over 30 individual components in a specific sequence. This includes removing gears, shafts, bearings, seals, and housing components. The assembly process reverses the disassembly steps and provides details on cleaning, lubricating, and setting proper bearing preloads using shims. Special tools are required for tasks like installing dual-cone seals.
This document provides instructions for removing and installing various engine components on a Caterpillar 330 L excavator, including:
1. The cylinder head removal procedure involves removing fuel injection lines, exhaust manifold, rocker shaft and pushrods, and bolts holding the head to the cylinder block.
2. Installing the cylinder head requires cleaning surfaces, installing gaskets and bolts, adjusting valves, and reinstalling other removed components.
3. Removal of the spacer plate requires removing seals and installing a new gasket, while installation requires cleaning and installing the plate with new seals.
Caterpillar cat 330 b excavator (prefix 2rr) service repair manual (2rr00001 ...hfjsekekmmd
This document provides instructions for removing and reassembling the final drives on an excavator model 330B. The summary is:
1. The final drive is disassembled by removing components like the ring gear, carrier assemblies, planetary gears, and seals.
2. To reassemble, components are cleaned and seals/bearings installed before refitting parts like the carrier assemblies, ring gear and sprockets.
3. Precise measurements are taken to determine the correct shim thickness for installing the gear to achieve proper bearing preload.
Caterpillar cat 318 e l excavator (prefix dzf) service repair manual (dzf0000...fjskekdmjekm
The document provides instructions for removing and installing a crankshaft timing ring on a C4.4 engine. It describes:
1) Removing the crankshaft first according to a separate procedure.
2) Cleaning the crankshaft timing ring and inspecting it for wear or damage, replacing if needed.
3) Lubricating and installing the timing ring on the crankshaft, ensuring it is seated properly.
Caterpillar cat 330 c fm excavator (prefix b4n) service repair manual (b4n000...fjsjekdmmeme
This document provides instructions for servicing components of a Caterpillar 330C FM Excavator engine, including:
- Installing the cylinder head, which involves positioning a new gasket, attaching lifting tools to the head, applying anti-seize compound, and tightening bolts in a specific sequence.
- Removing and installing the camshaft, which requires removing other parts first like the rocker arm and front cover, then using hooks to position lifters and removing/installing the camshaft.
- Removing and installing the camshaft gear by first removing the camshaft, pressing it off the gear, heating the gear, and pressing it back onto the camshaft
Caterpillar cat 330 c l excavator (prefix jnk) service repair manual (jnk0000...hhjsekmdmm
The document provides installation instructions for a gear pump used in the fan drive of an excavator. It outlines 20 steps to assemble the piston motor that drives the hydraulic fan. These include pressing bearings onto shafts, installing springs, O-rings, seals, and housing components in the proper order and orientation. Precautions are given to ensure cleanliness and prevent injury from parts under pressure.
Caterpillar cat 16 g motor grader (prefix 93u) service repair manual (93u0267...fjsekdmmeed
This document provides instructions for removing and installing rocker shaft assemblies, push rods, valve lifters, and related components on a 3406C diesel engine. The key steps include:
1. Removing the valve covers, fuel lines, rocker shaft assemblies, push rods, and valve lifters. Identification marks should be made on removed parts.
2. Cleaning and lubricating replacement parts as needed before installation. Parts should be installed in their original locations when possible.
3. Installing the valve lifters, push rods, rocker shaft assemblies, fuel lines, adjusting the valves, and replacing the valve covers. Torque specifications and safety notices are provided throughout.
Caterpillar cat 390 f excavator (prefix hng) service repair manual (hng00001 ...fjskefksemer
This document provides instructions for removing and installing the front gear group of a C18 engine. The removal procedure involves removing 14 bolts, plates, gears and seals. Special care must be taken to mark gear orientations and not turn the crankshaft during removal. The installation procedure describes cleaning components, applying thread lock compound, installing 14 gears, plates and seals in the correct order and orientation, and adjusting backlash between gears. Proper removal and installation is important to avoid engine damage.
Caterpillar cat 330 c excavator (prefix gag) service repair manual (gag00001 ...hfjsekekmmd
1) The document provides instructions for disassembling and assembling the travel motor of a 330C excavator.
2) It describes 28 steps to disassemble the travel motor by removing components like the head, springs, plates, and seals.
3) It then describes 28 steps for reassembling the travel motor, placing components back in the reverse order and noting alignment and torque specifications.
Caterpillar cat 966 c wheel loader (prefix 18b) service repair manual (18b012...fjsjjekdkme
This document provides instructions for installing a fuel injection pump housing and governor on a Caterpillar 3306 engine. The steps include:
1. Ensuring the number 1 piston is at top center position for timing.
2. Installing alignment tools in the flywheel housing.
3. Checking valve timing and turning the flywheel until the number 1 piston is at the correct position.
4. Installing the fuel injection pump housing and governor according to the assembly procedure.
This document provides instructions for installing a flywheel and removing and installing a wet back end flywheel housing on a Caterpillar 320 GC excavator. It describes using guide studs and lifting devices to position the heavy flywheel and housing. Torque specifications and tightening sequences are given for installing mounting bolts. Replacing seals, gaskets and dowels is also covered.
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. The procedure involves using specialty tools to compress the valve springs so that the valves, springs, and related components can be safely accessed and removed or installed one piston at a time. Proper tool use and safety precautions are emphasized to avoid injury from released spring forces.
The document provides instructions for removing the fuel injection pump from a Caterpillar 320D L excavator with a C6.4 engine. It lists the required tools and safety notices, then gives a step-by-step procedure involving disconnecting fuel lines and harness assemblies, removing mounting hardware, and taking off the pump while keeping identification marks aligned for installation. Cleanliness is emphasized throughout to prevent contaminants from entering the system.
Caterpillar cat 320 l track type excavator (prefix 2dl) service repair manual...ddkkddm
This document provides instructions for installing and removing various engine components on Caterpillar 320, 320L, and 320N track-type excavators, including:
- Removing and installing inlet and exhaust valve seals
- Removing the engine oil filter base
- Installing the engine oil filter base
- Removing the engine oil cooler
- Disassembling the engine oil cooler
- Reassembling the engine oil cooler
- Installing the engine oil cooler
The summaries provide the main steps and components involved in each procedure.
This document provides instructions for connecting a separated track on a 320D LN excavator. It describes using hydraulic tools and pins to lift the track into position and connect the master pin. Cleanliness is important to prevent dirt from entering during reassembly. The track must be positioned correctly and tools are needed if the pin cannot be manually installed.
Caterpillar cat 320 d2 l excavator (prefix gba) service repair manual (gba000...ddkkddm
This document provides instructions for removing the fuel injector from a Caterpillar 320D2 excavator engine. It lists the required tools which include a fuel injector puller and capping kit. The procedure involves disconnecting fuel lines from the injector, plugging the injector, removing mounting bolts and clamps, and using a puller tool to remove the fuel injector from the engine. Care must be taken to contain any fluids and ensure all parts are clean.
Caterpillar cat 320 d2 l excavator (prefix dnp) service repair manual (dnp000...ddkkddm
The document provides instructions for assembling and installing the swing drive on a 320D2 excavator. It describes 22 steps to assemble components like bearings, gears, housings and seals. The final step is to install the assembled swing drive and refer to other instructions for installing the swing motor.
This document provides instructions for removing the fuel injector from a Caterpillar 320D2 excavator engine. It lists the required tools which include a fuel injector puller and capping kit. The procedure involves disconnecting fuel lines from the injector, plugging the injector, removing mounting bolts and clamps, and using a puller tool to remove the fuel injector from the engine. Care must be taken to contain any fluids and ensure all parts are clean.
The document provides instructions for assembling and installing the swing drive on a 320D2 excavator. It describes 22 steps to assemble components like bearings, gears, housings and seals. The final step is to install the assembled swing drive and refer to other instructions for installing the swing motor.
Caterpillar cat 320 d ln excavator (prefix wbn) service repair manual (wbn000...ddkkddm
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D LN excavator with a C6.4 engine. It describes the required tools and safety precautions, and gives a step-by-step process for compressing the valve springs, removing old parts, and installing new parts in their proper positions and orientations. The document also provides specifications for inspecting valve components to ensure proper dimensions are met.
Caterpillar cat 320 d l excavator (prefix kgf) service repair manual (kgf0000...ddkkddm
This document provides instructions for disassembling and assembling the travel motor of a 320D L excavator. The disassembly process includes 27 steps to remove components like the head, fittings, seals, brake piston, plates, and barrel assembly. The assembly section outlines 13 steps including installing seals, keys, cam plate, springs, and piston shoe assemblies back into the barrel assembly and body of the travel motor. Special notices are provided regarding alignment marks, pressing components, and engaging the cam plate during assembly.
Caterpillar cat 320 d l excavator (prefix dhk) service repair manual (dhk0000...ddkkddm
This document provides instructions for removing and installing a boom cylinder on a 320D excavator. It includes:
1) Detailed steps to remove the boom cylinder such as releasing hydraulic pressure, removing mounting bolts and pins, and lifting the cylinder off the machine.
2) Information on required tools and torque specifications for reassembly.
3) The installation procedure which reverses the removal steps such as lifting the cylinder back into place, reinstalling pins and bolts, and reconnecting hydraulic lines.
Safety precautions are provided to relieve hydraulic pressure before disassembling cylinders. Torque specifications are included for correct reassembly.
Caterpillar cat 320 d l excavator (prefix a9f) service repair manual (a9f0000...ddkkddm
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. The procedure involves using specialty tools to compress the valve springs so that the valves, springs, and related components can be safely accessed and removed or installed one at a time. Proper cleaning and inspection of parts is emphasized to prevent premature wear. The work must be done with the pistons positioned correctly to avoid parts falling into the cylinders.
Caterpillar cat 320 d excavator (prefix kgf) service repair manual (kgf00001 ...ddkkddm
This document provides instructions for disassembling and assembling the travel motor of a 320D L Excavator. The disassembly process includes 27 steps to remove components like the head, fittings, seals, brake piston, plates, and barrel assembly. The assembly section outlines 13 steps including installing seals, keys, cam plate, springs, and piston shoe assemblies back into the barrel assembly and travel motor body. Special care must be taken to align parts and not allow components to separate during disassembly and assembly.
Caterpillar cat 320 d excavator (prefix dhk) service repair manual (dhk00001 ...ddkkddm
This document provides instructions for removing and installing the boom cylinder on a 320D and 320D L excavator. The procedure involves releasing hydraulic pressure, removing attachment points, and using lifting devices to maneuver the heavy cylinder. Special tools are required to remove pins connecting the cylinder. Torque specifications are provided for reinstallation. Safety precautions are described, such as relieving pressure before disassembly to avoid injury.
Caterpillar cat 320 track type excavator (prefix 2 dl) service repair manual ...ddkkddm
This document provides instructions for removing and installing valve stem seals on Caterpillar 320, 320L, and 320N track-type excavators. The procedure involves using a seal pick tool to remove the old seals from the valve guides and install new seals. Technicians are instructed to keep all parts clean and coat the new seals with engine oil during installation.
Caterpillar cat 320 s excavator (prefix 4 zj) service repair manual (4zj00460...ddkkddm
1. The document provides instructions for removing and installing final drives on 320-series excavators. It describes disconnecting hydraulic lines, removing mounting bolts, and using lifting tools to remove the final drives from the excavator.
2. Detailed steps are given for disassembling the final drives, including removing gears, carriers, seals, and other components. Alignment marks should be made for reassembly.
3. Reassembly involves cleaning parts, applying threadlock and lubricant, and torquing bolts to specification. Seals and bearings must be installed correctly to prevent damage.
Caterpillar cat 320 s excavator (prefix 3 xk) service repair manual (3xk00822...ddkkddm
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 320 excavator models. It describes the required tools and gives a step-by-step process including removing clips and pins, sliding tubes, and removing/installing parts like the governor, linkage, and seals using special tools. References are provided for more information on governors and linkage inspection procedures.
Caterpillar cat 320 n excavator (prefix 4 zj) service repair manual (4zj00460...ddkkddm
1. The document provides instructions for removing and installing final drives on 320-series excavators. It describes disconnecting hydraulic lines, removing mounting bolts, and using hoists to lift heavy components like the final drive, ring gear, and carrier assemblies.
2. Detailed steps are given for disassembling the final drive components, including removing planetary gears, sun gears, and thrust washers. Special tools and alignment marks are used to aid reassembly.
3. Reassembly involves cleaning components, applying threadlock and anti-seize compound, and adjusting bearing preload with shims to achieve the correct specifications. Duo-Cone seals must be installed without damage to provide sealing between housings.
Caterpillar cat 320 n excavator (prefix 3 xk) service repair manual (3xk00822...ddkkddm
This document provides instructions for removing and installing a fuel injection control linkage on Caterpillar 320 excavator models. The removal procedure involves taking out the rocker shaft and pushrods, then removing clips and a clevis pin connecting the governor to the linkage. Installation requires reattaching the linkage with bolts and setting brackets, then inserting the clevis pin and clip using special tools. Compressing injector springs with another tool is also part of the installation process.
Caterpillar cat 320 l excavator (prefix 4 zj) service repair manual (4zj00460...ddkkddm
This document provides instructions for removing and installing final drives on 320-series excavators. It outlines the steps to release hydraulic pressure, remove the final drive housing, and disassemble/reassemble the internal components. The process involves removing 20 bolts, hydraulic lines, and using lifting tools to maneuver heavy internal parts like carriers, gears, and housings weighing up to 82 kg. Proper cleaning, lubrication, and torque specifications are noted to ensure correct reassembly.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320-A EXCAVATOR 2DL
Configuration: 320, 320L & 320N TRACK-TYPE EXCAVATORS 2DL00214-UP (MACHINE) POWERED BY 3066 ENGINE
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01150941
Inlet and Exhaust Valve Seals - Remove and Install
SMCS - 1104-010-SA
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-1720 Seal Pick 1
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4(W)
w
2019/12/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
3. Illustration 1 g00610601
Illustration 2 g00610605
1. Use Tool (A) to remove valve stem seal (1) from the inlet and exhaust valve guide.
Illustration 1 shows the removal of the valve stem seal, when the valve guide (2) is removed
from cylinder head (4) .
Illustration 2 shows the removal of the valve stem seal, while the valve guide (2) is installed
in cylinder head (4) .
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 5P-1720 Seal Pick 1
NOTICE
Keep all parts clean from contaminants.
2/4(W)
w
2019/12/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
4. Contaminants may cause rapid wear and shortened component life.
Note: Do not apply any oil or sealant to the mating surface of the valve seal that comes into
contact with the valve guide. When the valve seal is installed, coat the surface of the valve stem
with engine oil in order to ensure initial lubrication of the seal lip.
Illustration 3 g00610601
Illustration 4 g00610605
1. Place the new valve stem seal in position on the valve guide.
2. Use Tool (A) to assist in installing the new valve stem seal.
Illustration 3 shows the installation of the valve stem seal, when the valve guide (2) is
removed from the cylinder head (4) .
Illustration 4 shows the installation of the valve stem seal, while the valve guide (2) is
installed in the cylinder head (4) .
Note: After the valve stem seal is installed on the valve guide, ensure that the seal is
properly installed in the groove of the valve guide.
3/4(W)
w
2019/12/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
5. End By: Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Dec 21 17:29:16 UTC+0800 2019
4/4(W)
w
2019/12/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320-A EXCAVATOR 2DL
Configuration: 320, 320L & 320N TRACK-TYPE EXCAVATORS 2DL00214-UP (MACHINE) POWERED BY 3066 ENGINE
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01565892
Engine Oil Filter Base - Remove
SMCS - 1306-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench Assembly 1
Hot oil and components can cause personal injury.
Do not allow hot oil or components to contact skin.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
1/3(W)
w
2019/12/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
7. Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00813775
Illustration 2 g00813789
1. Use Tool (A) and remove oil filter (2) from engine oil filter base (3) .
2. Remove the bolts (1) and washers from the engine oil filter base (3) .
3. Remove engine oil filter base (3) from the engine.
2/3(W)
w
2019/12/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
8. 4. Check the condition of O-ring seals (4). Replace the O-ring seals, if the O-ring seals are
worn or damaged.
Illustration 3 g00813823
5. If necessary, remove eight bolts (6) and the washers in order to remove plate (5) from the
engine.
6. Check the condition of gasket (not shown). Replace the gasket, if the gasket is worn or
damaged.
7. Check engine oil filter base (3) and plate (5) for clogging and cracks. Replace damaged
components with replacement parts.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Dec 21 17:30:12 UTC+0800 2019
3/3(W)
w
2019/12/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
9. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320-A EXCAVATOR 2DL
Configuration: 320, 320L & 320N TRACK-TYPE EXCAVATORS 2DL00214-UP (MACHINE) POWERED BY 3066 ENGINE
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01565969
Engine Oil Filter Base - Install
SMCS - 1306-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00813823
1. Secure gasket and plate (5) to the cylinder block with eight bolts (6) .
1/2(W)
w
2019/12/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
10. Illustration 2 g00813789
2. Check the condition of O-ring seals (4). Replace the O-ring seals, if the O-ring seals are
damaged.
Note: Coat all of the O-ring seals with clean engine oil prior to installation.
3. Install the O-ring seals (4) on engine oil filter base (3) .
Illustration 3 g00813775
4. Secure engine oil filter base (3) to the plate (5) with four bolts (1) and the washers.
5. Install the engine oil filter (2) to the engine oil filter base (3) .
Note: Follow the installation procedure on the engine oil filter in order to install the engine
oil filter on the engine oil filter base.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Dec 21 17:31:08 UTC+0800 2019
2/2(W)
w
2019/12/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320-A EXCAVATOR 2DL
Configuration: 320, 320L & 320N TRACK-TYPE EXCAVATORS 2DL00214-UP (MACHINE) POWERED BY 3066 ENGINE
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615275
Engine Oil Cooler - Remove
SMCS - 1378-011
Removal Procedure
Start By:
A. Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump
- Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/2(W)
w
2019/12/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
12. Illustration 1 g00611319
1. If necessary, remove bolt (1) and the washer from the cylinder head.
2. Remove oil tube assembly (dipstick) (2) from the cylinder block.
3. Check O-ring seal (3) (not shown) for wear or damage. Replace the O-ring seal, if the O-
ring seal is worn or damaged.
Illustration 2 g00611320
4. Remove bolts (4) and the washers that secure the oil cooler to the engine cylinder block.
The 3066 Engine has 24 bolts and washers while the 3064 Engine has 16 bolts and washers.
5. Remove engine oil cooler (5) and gasket (6) (not shown) from the engine cylinder block.
Check the gasket for wear or damage. Replace the gasket, if the gasket is worn or damaged.
Note: Check the oil cooler cover for cracks. Replace the cover, if the cover is cracked.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Dec 21 17:32:04 UTC+0800 2019
2/2(W)
w
2019/12/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320-A EXCAVATOR 2DL
Configuration: 320, 320L & 320N TRACK-TYPE EXCAVATORS 2DL00214-UP (MACHINE) POWERED BY 3066 ENGINE
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01152039
Engine Oil Cooler - Disassemble
SMCS - 1378-015
Disassembly Procedure
Start By:
A. Remove the oil cooler. Refer to Disassembly and Assembly, "Engine Oil Cooler - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/3(W)
w
2019/12/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
14. Illustration 1 g00618921
Illustration 2 g00611507
1. Remove four nuts (1) and the washers from the oil cooler core (3) .
2. Remove oil cooler core (3) from oil cooler cover (2) .
Note: Check the engine oil cooler core for cracks, clogging, and ruptures.
3. Remove two gaskets (4) from the oil cooler core. Check the gasket for wear or damage.
Replace the gaskets, if necessary.
2/3(W)
w
2019/12/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320-A EXCAVATOR 2DL
Configuration: 320, 320L & 320N TRACK-TYPE EXCAVATORS 2DL00214-UP (MACHINE) POWERED BY 3066 ENGINE
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01152137
Engine Oil Cooler - Assemble
SMCS - 1378-016
Assembly Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2(W)
w
2019/12/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
16. Illustration 1 g00618921
Illustration 2 g00611507
1. Install two gaskets (4) onto the oil cooler core (3) .
2. Install the oil cooler cover (2) onto the oil cooler core (3) .
3. Install four nuts (1) and the washers, which secure the oil cooler core to the oil cooler cover.
4. Tighten the four nuts (1) .
End By: Install the oil cooler. Refer to Disassembly and Assembly, "Engine Oil Cooler - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Dec 21 17:33:55 UTC+0800 2019
2/2(W)
w
2019/12/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320-A EXCAVATOR 2DL
Configuration: 320, 320L & 320N TRACK-TYPE EXCAVATORS 2DL00214-UP (MACHINE) POWERED BY 3066 ENGINE
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615279
Engine Oil Cooler - Install
SMCS - 1378-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00611320
1. Install engine oil cooler (5) and new gasket (6) (not shown). Ensure that all mating surfaces
are clean. Install bolts (4) and washers in order to secure the engine oil cooler to the engine
cylinder block. The 3066 Engine has 24 bolts and washers while the 3064 Engine has 16
bolts and washers.
1/2(W)
w
2019/12/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
18. Illustration 2 g00611319
2. Install oil tube assembly (dipstick) (2) into the cylinder block.
Note: Apply clean engine oil to the O-ring seal (3) (not shown) before installation.
3. Install bolt (1) and the washer into the cylinder head.
End By: Install the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection
Pump - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Dec 21 17:34:51 UTC+0800 2019
2/2(W)
w
2019/12/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
19. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320-A EXCAVATOR 2DL
Configuration: 320, 320L & 320N TRACK-TYPE EXCAVATORS 2DL00214-UP (MACHINE) POWERED BY 3066 ENGINE
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615285
Engine Oil Relief Valve - Remove and Install
SMCS - 1315-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00607236
1/3(W)
w
2019/12/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
21. Illustration 2 g00607247
1. Remove threaded plug (1) and the shim (2) for the engine oil relief valve from the right side
of the cylinder block.
2. Remove the spring (3) and spring seat (4) from the cylinder block.
Note: Check the spring seat (4) and the valve seat for an abnormal contact pattern. Inspect the
spring (3) for weakness or damage. If necessary, replace the engine oil relief valve with a new
part.
Note: Check the cylinder block for oil passages that are clogged.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3(W)
w
2019/12/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
22. Illustration 3 g00607247
Illustration 4 g00607236
1. Install spring seat (4) and spring (3) in the cylinder block.
2. Install shim (2) and threaded plug (1) in the cylinder block.
3. Tighten threaded plug (1) of the engine oil relief valve to a torque of 49 ± 5 N·m (36 ± 4 lb
ft).
Note: Test the opening pressure for the engine oil relief valve. The opening pressure for the
relief valve is 343 ± 20 kPa (50 ± 3 psi). Make adjustments by shimming, if necessary.
For more information, refer to Specifications, "Engine Oil Relief Valve".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Dec 21 17:35:47 UTC+0800 2019
3/3(W)
w
2019/12/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...