1. Nile Technical Training center is the one of the Professional Technical Training center located on the Capital city
Kathmandu of Nepal. The primary objective of the center was to develop the skill of general workers on different
technical skills for recruitment to Middle East, since years of experience, we have good infrastructure, materials and
the trade testing manual which is highly appreciate by the foreign companies. We have deployed more than 10,000
trained skilled candidates who had gone to Middle East in different companies.
We had GCC experienced trainer as well as technicians for each categories, we not only test the trade but also
encourage being better skill then they score in test.
Currently we are doing the trade test & training on ( Mason : Block/Plaster/Tile/Marble , Carpenter : Finishing/
Shutting / Polishing , Steel Fixture , Plumbing , Electrician ,Welder :1G to 6G , Scaffolding , Insulator
,Painter : Wall Painter/Spray Painter ,Alminium Fabricator, Gypsum Board.
Some Basic Features of our Training Center:
License Copy: Sample copy of Training & Trade test Certificate:
Training & Testing Module:
Mason:
2. Training & Testing System
-Basic masonry materials, tools, techniques, and safety precautions
-Learn to Handle tools used on masonry.
-Learn the Measurement & Measuring tools used in Masonry.
-Learn About the Mortar equipment used in Masonry.
-Learn How to use power tools used in Masonry ( Masonry Saws ,Splitters,Grinders and drills &
powder actuated tools )
- Learn about the power equipment used in Masonry (Mortar Mixure,Masonry
Pump,Vibrator,Hydraulic Pump etc )
-Learn about lifting equipment used in Masonary ( Mounted and Portable Hoists )
-Learning calculation of distances and areas common in masonry work, describes the information found
on residential construction drawings, and reviews the role of specifications, standards, and codes
Performance Tasks
• Properly use the following personal protective equipment: (Face shield/Protective lenses/Hearing
protection/Respirator)
• Properly use the following personal protective equipment: (Safety harness /Connector/ Anchorage
device)
• Demonstrate the proper use of a rule.
• Demonstrate the proper use of a level.
• Use the correct procedures for fueling and
Starting a mixer.
• Assemble and disassemble tubular frame scaffold.
• Use a mason’s rule to measure a space and verify its squareness.
• Use a rule to measure fractional dimensions.
• Locate information on construction drawings.
• Finishing of his work
Training Will be design for 30 days, 8 hours per day for Raw people. if they already have work
experience and in our trade test if they get below 70% on practical and theoretical , then we
refer them 15 days training.
3. Carpentry:
Training & Trade Testing
Finishing Carpentry / Polishing
-Basic Carpentry materials, tools, techniques, and safety precautions
-Learn to Handle tools used on Carpentry.
-Learn the Measurement & Measuring tools used in Carpentary.
-Learn About the wood sizes and cutting shapes .
-Material Handling and manual sharping them.
-Joint knowledge in different location of carpentry
Shutting Carpentry
-Basic Carpentry materials, tools, techniques, and safety precautions
-Carry out general demolition of minor building structures
-Carry out setting out
-Carry out levelling operations
-Work effectively and sustainably in the construction industry
-Carry out measurements and calculations
-Read and interpret plans and specifications
-Carry out excavation
-Use explosive power tools
-Construction and erection of frames, trusses, eaves and roofs field of work
-Install and replace windows and doors
-Frame and fit wet area fixtures
-Install lining, panelling and moulding
-Construct timber external stairs
-Formwork construction field of work (Construct, erect and dismantle formwork for stairs and ramps/ Erect and
dismantle formwork to suspended slabs, columns, beams and walls/Erect and dismantle jump form
formwork/Erect and dismantle slip form formwork
-Assemble partitions,Install exterior cladding and curtain walling
Steel Fixure :
Steel fixture Training & Trade test Module
4. -Basic Steel Fixture materials, tools, techniques, and safety precautions
-Learn to Handle tools used on Steel Fixture.
-Learn the Measurement & Measuring tools used in Steel Fixture.
-Learn About the rod sizes and cutting shapes.
-Cut and bend materials using oxy-LPG equipment
-Place and fix reinforcement materials
-Arc weld reinforcement steel
-Machine cut reinforcement materials
-Splice and anchor using mechanical methods
-Carry out monostrand,multistrand and stressbar post-tensioning.
Plumbing and Pipe fitting:
Plumbing Training & Trade Test
-Basic Plumbing and Pipe fitting materials, tools, techniques, and safety precautions
-Learn to Handle tools used on Plumbing and Pipe fitting.
-Learn the Measurement & Measuring tools used in Plumbing and Pipe fitting.
-Learn About the cutting erecting the pipe.
-Threading & Fitting
-PVC Joint PPR Joint and GI Joint System
-Leckages Control System
-Map Reading and Understanding
-Pipefitting, welding and steamfitting
-Assembling and testing pipe joints and systems
-Tanks, pumps and plumbing maintenance
-Gas and arc welding and cutting
-Refrigeration, heating and air conditioning tools, materials and fundamentals
5. Painter ( Wall / Spray ):
Training Module of Wall & Spray Painter
-Basic Painting materials, tools, techniques, and safety precautions
-Learn to Handle tools used on Painting.
-Learn the Measurement & Measuring tools used in Wall & Spray Painter.
-Basic knowledge of color and putting system.
-Spray machine operation and control
Scaffolding:
Scaffolding Training and Trade Testing Module
-Basic Scaffolding materials, tools, techniques, and safety precautions
-Learn to Handle tools used on Scaffolding.
-Learn the Leveling & Material used in Scaffolding.
-Material Handling and estimating
-Tower Management System
-Scaffolding types and its features
-Scaffolding areas and general information of workstations .
6. Electrician:
Training Module for Electrician ( House Wiring )
-Basic Electrical materials, tools, techniques, and safety precautions
-Learn to Handle tools used on Electrician.
-Learn the Map Reading and Understanding the symbols and signals.
- Map Drawing, understanding and troubleshooting
-Underground pipe expansion system
-DB Box Input output system
-Voltmeter and Ampere meter checking and maintaining system
-Switch & Power Box Installation and Troubleshooting
-Power Control Management System
-Basic 3 Phase knowledge
7. Aluminum Fabricator:
Aluminum Fabricator Training
-Basic Fabrication materials, tools, techniques, and safety precautions
-Learn to Handle tools used on Fabrication.
-Learn the Map Reading and Understanding the symbols.
-Material Knowledge
-Section Knowledge ( Door & Window Partition etc )
-Glass & Net Fitting
-Basic knowledge of Steel Fabrication too
Insulator:
Aluminum Fabricator Training
-Basic Insulator materials, tools, techniques, and safety precautions
-Learn to Handle tools used on Insulation.
-Learn the Map Reading and Drawings
-Material Knowledge
-Glass wool cutting practice
-Glass & Net Fitting
-Bent cutting system ( 90 Degree , Branch Bent Support , T Etc )
-Cutting and Fitting
Some more Pictures of our training Center:
Office :
9. Our All the Training Module are One month ,8 hours per day / 15 Days ,8 hours per day , Except public
holiday . As necessary we expand their training period until they score the adequate performance.
